A Commands

aaa accounting default

[no] aaa accounting default { group <s0> [ <s1> [ <s2> [ <s3> [ <s4> [ <s5> [ <s6> [ <s7> ] ] ] ] ] ] ] [ local1 | none ] | local [ none1 ] | none2 }

Syntax Description

no

(Optional) Negate a command or set its defaults

aaa

Configure aaa functions

accounting

Configure accounting methods

default

Configure default methods

group

Specify server groups to redirect the accounting logs

s0

Server group name

s1

(Optional) Server group name

s2

(Optional) Server group name

s3

(Optional) Server group name

s4

(Optional) Server group name

s5

(Optional) Server group name

s6

(Optional) Server group name

s7

(Optional) Server group name

none

(Optional) No accounting

none1

(Optional) No accounting

none2

No accounting

local

Use local accounting

local1

(Optional) Use local accounting

Command Mode

  • /exec/configure

aaa accounting dot1x default group

[no] aaa accounting dot1x default group <grp_name> +

Syntax Description

aaa

Configure aaa functions

accounting

Configure accounting methods

dot1x

accounting methods for dot1x

default

default aaa methods

grp_name

server group name

Command Mode

  • /exec/configure

aaa accounting onep default group

[no] aaa accounting onep default group <grp_name> +

Syntax Description

aaa

Configure aaa functions

accounting

configure accounting methods

grp_name

server group name

Command Mode

  • /exec/configure

aaa authentication dot1x default group

[no] aaa authentication dot1x default group <grp_name> +

Syntax Description

aaa

Configure aaa functions

authentication

Configure authentication methods

grp_name

server group name

Command Mode

  • /exec/configure

aaa authentication login ascii-authentication

[no] aaa authentication login ascii-authentication

Syntax Description

no

(Optional) Negate a command or set its defaults

aaa

Configure aaa functions

authentication

Configure authentication methods

login

Configure methods for login

ascii-authentication

enable ascii authentication

Command Mode

  • /exec/configure

aaa authentication login console

[no] aaa authentication login console { group <s0> [ { local1 | none | <s1> [ { local1 | none | <s2> [ { local1 | none | <s3> [ { local1 | none | <s4> [ { local1 | none | <s5> [ { local1 | none | <s6> [ { local1 | none | <s7> [ { local1 | none } ] } ] } ] } ] } ] } ] } ] } ] | local | none }

Syntax Description

no

(Optional) Negate a command or set its defaults

aaa

Configure aaa functions

authentication

Configure authentication methods

login

Configure methods for login

console

Configure console methods

group

Specify server groups

s0

Server group name

none

(Optional) No authentication

s1

(Optional) Server group name

none

(Optional) No authentication

s2

(Optional) Server group name

none

(Optional) No authentication

s3

(Optional) Server group name

none

(Optional) No authentication

s4

(Optional) Server group name

none

(Optional) No authentication

s5

(Optional) Server group name

none

(Optional) No authentication

s6

(Optional) Server group name

none

(Optional) No authentication

s7

(Optional) Server group name

none

(Optional) No authentication

local

Use local username authentication

local1

(Optional) Use local username authentication

none

No authentication

Command Mode

  • /exec/configure

aaa authentication login default

[no] aaa authentication login default { group <s0> [ { local1 | none | <s1> [ { local1 | none | <s2> [ { local1 | none | <s3> [ { local1 | none | <s4> [ { local1 | none | <s5> [ { local1 | none | <s6> [ { local1 | none | <s7> [ { local1 | none } ] } ] } ] } ] } ] } ] } ] } ] | local | none }

Syntax Description

no

(Optional) Negate a command or set its defaults

aaa

Configure aaa functions

authentication

Configure authentication methods

login

Configure methods for login

default

Configure default methods

group

Specify server groups

s0

Server group name

none

(Optional) No authentication

s1

(Optional) Server group name

none

(Optional) No authentication

s2

(Optional) Server group name

none

(Optional) No authentication

s3

(Optional) Server group name

none

(Optional) No authentication

s4

(Optional) Server group name

none

(Optional) No authentication

s5

(Optional) Server group name

none

(Optional) No authentication

s6

(Optional) Server group name

none

(Optional) No authentication

s7

(Optional) Server group name

none

(Optional) No authentication

local

Use local username authentication

local1

(Optional) Use local username authentication

none

No authentication

Command Mode

  • /exec/configure

aaa authentication login default fallback error local

[no] aaa authentication login { default | console } fallback error local

Syntax Description

no

(Optional) Negate a command or set its defaults

aaa

Configure aaa functions

authentication

Configure authentication methods

login

Configure methods for login

default

Configure default methods

console

Configure console methods

fallback

Configure fallback behavior

error

Fallback in case all AAA servers configured for remote authentication are unreachable (Authentication error)

local

Fallback to local authentication

Command Mode

  • /exec/configure

aaa authentication login enable

[no] aaa authentication login { mschap | mschapv2 | chap } enable

Syntax Description

no

(Optional) Negate a command or set its defaults

aaa

Configure aaa functions

authentication

Configure authentication methods

login

Configure methods for login

mschap

MSCHAP authentication for login

mschapv2

MSCHAP V2 authentication for login

chap

CHAP authentication for login

enable

enable the authentication for login

Command Mode

  • /exec/configure

aaa authentication login error-enable

[no] aaa authentication login error-enable

Syntax Description

no

(Optional) Negate a command or set its defaults

aaa

Configure aaa functions

authentication

Configure authentication methods

login

Configure methods for login

error-enable

enable display of error message on login failures

Command Mode

  • /exec/configure

aaa authentication login invalid-username-log

[no] aaa authentication login invalid-username-log

Syntax Description

no

(Optional) Negate a command or set its defaults

aaa

Configure aaa functions

authentication

Configure authentication methods

login

Configure methods for login

invalid-username-log

enable invalid username log

Command Mode

  • /exec/configure

aaa authentication login password-aging enable

[no] aaa authentication login password-aging enable

Syntax Description

no

(Optional) Negate a command or set its defaults

aaa

Configure aaa functions

authentication

Configure authentication methods

login

Configure methods for login

password-aging

password-aging authentication for login

enable

enable password-aging notification

Command Mode

  • /exec/configure

aaa authentication onep default group

[no] aaa authentication onep default group <grp_name> +

Syntax Description

aaa

Configure aaa functions

authentication

Configure authentication methods

grp_name

server group name

Command Mode

  • /exec/configure

aaa authentication rejected

[no] aaa authentication rejected

Syntax Description

no

Negate a command or set its defaults

aaa

Configure aaa functions

authentication

Configure authentication methods

rejected

Set max number of fail attempts

Command Mode

  • /exec/configure

aaa authentication rejected in ban

aaa authentication rejected <i1> in <i2> ban <i3>

Syntax Description

aaa

Configure aaa functions

authentication

Configure authentication methods

rejected

Set max number of fail attempts

i1

Fail attempts max value

in

Watch period for fail attempts

i2

Time period in seconds

ban

Block time period

i3

Time period in seconds

Command Mode

  • /exec/configure

aaa authorization commands console

[no] aaa authorization { commands | config-commands } console { group <s0> [ { local | none | <s1> [ { local | none | <s2> [ { local | none | <s3> [ { local | none | <s4> [ { local | none | <s5> [ { local | none | <s6> [ { local | none | <s7> [ { local | none } ] } ] } ] } ] } ] } ] } ] } ] | local | none }

Syntax Description

no

(Optional) Negate a command or set its defaults

aaa

Configure aaa functions

authorization

Configure authorization methods

commands

Authorization for all exec-mode commands

config-commands

Authorization for config commands

console

Configure methods console

group

Specify server groups

s0

Server group name

s1

(Optional) Server group name

s2

(Optional) Server group name

s3

(Optional) Server group name

s4

(Optional) Server group name

s5

(Optional) Server group name

s6

(Optional) Server group name

s7

(Optional) Server group name

local

(Optional) Use local RBACL based authorization

none

(Optional) No authorization

Command Mode

  • /exec/configure

aaa authorization commands default

[no] aaa authorization { commands | config-commands } default { group <s0> [ { local | none | <s1> [ { local | none | <s2> [ { local | none | <s3> [ { local | none | <s4> [ { local | none | <s5> [ { local | none | <s6> [ { local | none | <s7> [ { local | none } ] } ] } ] } ] } ] } ] } ] } ] | local | none }

Syntax Description

no

(Optional) Negate a command or set its defaults

aaa

Configure aaa functions

authorization

Configure authorization methods

commands

Authorization for all exec-mode commands

config-commands

Authorization for config commands

default

Configure default methods

group

Specify server groups

s0

Server group name

s1

(Optional) Server group name

s2

(Optional) Server group name

s3

(Optional) Server group name

s4

(Optional) Server group name

s5

(Optional) Server group name

s6

(Optional) Server group name

s7

(Optional) Server group name

local

(Optional) Use local RBACL based authorization

none

(Optional) No authorization

Command Mode

  • /exec/configure

aaa authorization cts default group

[no] aaa authorization cts default group <grp_name> +

Syntax Description

aaa

Configure aaa functions

authorization

Configure authorization methods

cts

authorization methods for cts

default

default aaa methods

group

server group

grp_name

server group name

Command Mode

  • /exec/configure

aaa authorization ssh default group

[no] aaa authorization { ssh-publickey | ssh-certificate } default { group <s0> [ { local1 | <s1> [ { local1 | <s2> [ { local1 | <s3> [ { local1 | <s4> [ { local1 | <s5> [ { local1 | <s6> [ { local1 | <s7> [ { local1 } ] } ] } ] } ] } ] } ] } ] } ] | local }

Syntax Description

no

(Optional) Negate a command or set its defaults

aaa

Configure aaa functions

authorization

Configure authorization methods

ssh-publickey

Configure ssh publickey

ssh-certificate

Configure ssh certificate

default

Configure default ssh methods

group

Specify server groups

s0

Server group name

s1

(Optional) Server group name

s2

(Optional) Server group name

s3

(Optional) Server group name

s4

(Optional) Server group name

s5

(Optional) Server group name

s6

(Optional) Server group name

s7

(Optional) Server group name

local

Use local username authentication

local1

(Optional) Use local username authentication

Command Mode

  • /exec/configure

aaa bypass-user

[no] aaa bypass-user <s0> { [ accounting ] [ authorization ] | [ authorization ] [ accounting ] }

Syntax Description

no

(Optional) Negate a command or set its defaults

aaa

Configure aaa functions

bypass-user

Configure bypass user

s0

Enter the username

accounting

(Optional) Bypass accounting

authorization

(Optional) Bypass authorization

Command Mode

  • /exec/configure

aaa group server ldap

[no] aaa group server ldap <s0>

Syntax Description

no

(Optional) Negate a command or set its defaults

aaa

Configure aaa functions

group

Configure aaa server group

server

Configure aaa server group

ldap

LDAP server group name

s0

LDAP server group name

Command Mode

  • /exec/configure

aaa group server radius

[no] aaa group server radius <s0>

Syntax Description

no

(Optional) Negate a command or set its defaults

aaa

Configure aaa functions

group

Configure aaa server group

server

Configure aaa server group

radius

RADIUS server group name

s0

RADIUS server group name

Command Mode

  • /exec/configure

aaa group server tacacs

[no] aaa group server tacacs <s0>

Syntax Description

no

(Optional) Negate a command or set its defaults

aaa

Configure aaa functions

group

Configure aaa server group

server

Configure aaa server group

tacacs

TACACS+ server group name

s0

TACACS+ server group name

Command Mode

  • /exec/configure

aaa test-authentication

[no] aaa test-authentication

Syntax Description

no

(Optional) Negate a command or set its defaults

aaa

Configure aaa functions

test-authentication

Test aaa authentication

Command Mode

  • /exec/configure

aaa test-radius-authentication

[no] aaa test-radius-authentication

Syntax Description

no

(Optional) Negate a command or set its defaults

aaa

Configure aaa functions

test-radius-authentication

Test aaa radius authentication

Command Mode

  • /exec/configure

aaa user default-role

[no] aaa user default-role

Syntax Description

no

(Optional) Negate a command or set its defaults

aaa

Configure aaa functions

user

Remotely authenticated user

default-role

Default role assigned by aaa-admin for remote authentication

Command Mode

  • /exec/configure

abort

abort

Syntax Description

abort

Exit region configuration mode, aborting changes

Command Mode

  • /exec/configure/spanning-tree/mst/configuration

abort

abort

Syntax Description

abort

abort itd session

Command Mode

  • /exec/configure/itd-session-device-group

abort

abort

Syntax Description

abort

Abort the current configuration session

Command Mode

  • /exec/configure

abort

abort

Syntax Description

abort

abort plb session

Command Mode

  • /exec/configure/plb-session-device-group

absolute-timeout

{ absolute-timeout <i0> | no absolute-timeout [ <i0> ] }

Syntax Description

no

Negate a command or set its defaults

absolute-timeout

Configure absolute timeout

i0

Enter timeout in minutes, 0 to disable

Command Mode

  • /exec/configure/line

absolute start

{ [ <seqno> ] | no } absolute { start <stime> <sday> <smonth> <syear> [ end <etime> <eday> <emonth> <eyear> ] | end <etime> <eday> <emonth> <eyear> }

Syntax Description

seqno

(Optional) Sequence number

no

Negate a command or set its defaults

absolute

Absolute time and date

start

Starting time and date

stime

Starting time

sday

Day of the month

smonth

Month

syear

Year

end

(Optional) Ending time and date

etime

(Optional) Ending time

eday

(Optional) Day of the month

emonth

(Optional) Month

eyear

(Optional) Year

Command Mode

  • /exec/configure/timerange

accept-lifetime month_a month_b month_c month_d month_e month_f month_g month_h month_i month_j month_k month_l duration infinite month_a month_b month_c month_d month_e month_f month_g month_h month_i month_j month_k month_l

{ { accept-lifetime [ local ] <stime> { month_a | month_b | month_c | month_d | month_e | month_f | month_g | month_h | month_i | month_j | month_k | month_l } <sday> <syear> { duration <dsec> | infinite | <etime> { month_a | month_b | month_c | month_d | month_e | month_f | month_g | month_h | month_i | month_j | month_k | month_l } <eday> <eyear> } } | { no accept-lifetime [ [ local ] <stime> { month_a | month_b | month_c | month_d | month_e | month_f | month_g | month_h | month_i | month_j | month_k | month_l } <sday> <syear> { duration <dsec> | infinite | <etime> { month_a | month_b | month_c | month_d | month_e | month_f | month_g | month_h | month_i | month_j | month_k | month_l } <eday> <eyear> } ] } }

Syntax Description

no

Negate a command or set its defaults

accept-lifetime

Set accept lifetime of key

local

(Optional) Specify time in local timezone

stime

HH:MM:SS Time to start <0-23>:<0-59>:<0-59>

etime

HH:MM:SS Time to end <0-23>:<0-59>:<0-59>

month_a

month_b

month_c

month_d

month_e

month_f

month_g

month_h

month_i

month_j

month_k

month_l

sday

Day of the month to start

eday

Day of the month to end

syear

Year to start

eyear

Year to start

duration

Set key lifetime duration

dsec

Duration in seconds

infinite

Never Expires

Command Mode

  • /exec/configure/keychain-key

access-class

[no] access-class <name> <inout>

Syntax Description

no

(Optional) Negate a command or set its defaults

access-class

Specify IPv4 access control for packets

name

List name

inout

Traffic direction

Command Mode

  • /exec/configure/line

access-class

{ access-class <aclname> } | { no access-class [ <aclname-ignore> ] }

Syntax Description

no

Negate a command or set its defaults

access-class

Filter incoming connections based on ACL

aclname

ACL name

aclname-ignore

(Optional) ACL name

Command Mode

  • /exe/configure/onep/tls

access-list

[no] access-list <acl-name>

Syntax Description

no

(Optional) Negate a command or set its defaults

access-list

ITD access-list name

acl-name

ITD user ACL name

Command Mode

  • /exec/configure/itd

access-list

[no] access-list <acl-name>

Syntax Description

no

(Optional) Negate a command or set its defaults

access-list

Configure access-list for PLB service

acl-name

Access-list name

Command Mode

  • /exec/configure/plb

access vlan

[no] access vlan <vlan>

Syntax Description

no

(Optional) Negate a command or set its defaults

access

access

vlan

vlan

vlan

Vlan

Command Mode

  • /exec/configure/smartc /exec/configure/smartc

action

[no] action { drop [ log ] | forward | redirect <intf> }

Syntax Description

no

(Optional) Negate a command or set its defaults

action

Specify the action clause

drop

Drop matched packets

log

(Optional) Log matched packets

forward

Forward matched packets

redirect

Redirect matched packets to the specified interface(s)

intf

Interface traffic is redirected to

Command Mode

  • /exec/configure/vacl

action

[no] action <label>

Syntax Description

no

Negate a command or set its defaults

action

Configure the actions to be executed

label

Enter the label <num1>[.<num2>] for action order num2 must be 0-9

Command Mode

  • /exec/configure/event-manager-applet

action cli

action <label> cli [ local ] <vsh_cmd>

Syntax Description

action

Configure the actions to be executed

label

Enter the label <num1>[.<num2>] for action order num2 must be 0-9

cli

Configure a VSH CLI action

local

(Optional) Execute the action in the same card on which the event happens

vsh_cmd

Enter the vsh command

Command Mode

  • /exec/configure/event-manager-applet

action counter name value op

action <label> counter name <counter-name> value <counter-value> op <op-val>

Syntax Description

action

Configure the actions to be executed

label

Enter the label <num1>[.<num2>] for action order num2 must be 0-9

counter

Specify the name of the counter

name

Specify the name of the counter

counter-name

Name of the counter

value

Specify the value to be applied to the counter

counter-value

Enter an integer value or a $ prefixed name (parameter substitution)

op

Specify the operator to be applied

op-val

Enter the value of the operator

Command Mode

  • /exec/configure/event-manager-applet

action eem test

action <label> eem test <param>

Syntax Description

action

Configure the actions to be executed

label

Enter the label <num1>[.<num2>] for action order num2 must be 0-9

eem

Event Manager command

test

Do test action

param

Test action parameter (dummy value)

Command Mode

  • /exec/configure/event-manager-applet

action event-default

action <label> event-default

Syntax Description

action

Configure the actions to be executed

label

Enter the label <num1>[.<num2>] for action order num2 must be 0-9

event-default

Do default action for the event

Command Mode

  • /exec/configure/event-manager-applet

action exceptionlog module syserr devid errtype errcode phylayer ports harderror

[no] action <label> exceptionlog module <mod> syserr <syserr> devid <id> errtype <type> errcode <code> phylayer <phy> ports <list> harderror <hard> [ { desc <str> } ]

Syntax Description

no

(Optional) Negate a command or set its defaults

action

Configure the actions to be executed

label

Enter the label <num1>[.<num2>] for action order num2 must be 0-9

exceptionlog

Exception log

module

Enter a module number

mod

Enter module number (integer value) or a $ prefixed parameter name

syserr

Enter syserr

syserr

Enter syserr code (hex value) or a $ prefixed parameter name

devid

Enter device id

id

Enter device id (integer value) or a $ prefixed parameter name

errtype

Enter error type

type

Error error type (integer value) or a $ prefixed parameter name

errcode

Enter error code

code

Enter error code (hex value) or a $ prefixed parameter name

phylayer

Enter phy layer

phy

Enter phy layer (integer value) or a $ prefixed parameter name

ports

Enter failed ports

list

List of ports. Example: 1,3,7-15

harderror

Irrecoverable error?

hard

Error sub-category

desc

(Optional) Enter error description

str

(Optional) Error description

Command Mode

  • /exec/configure/event-manager-applet

action forceshut reset-reason

[no] action <label2> forceshut [ { module { <module> | <mod-str> } | <s0> { <santa-cruz-range> | <santa-cruz-string> } } ] reset-reason <reset_reason_string>

Syntax Description

no

(Optional) Negate a command or set its defaults

action

Configure the actions to be executed

label2

Enter the label <num1>[.<num2>] for action order num2 must be 0-9

forceshut

Force the entire switch to shut down

module

(Optional) Optional. Module to be forced to shut down(optional argument)

module

(Optional) please enter the module number

mod-str

(Optional) Enter the module number (integer value) or a $ prefixed parameter name

s0

(Optional) Optional. Xbar to be forced to shut down(optional argument)

santa-cruz-range

(Optional) please enter the xbar number

santa-cruz-string

(Optional) Enter the xbar number (integer value) or a $ prefixed parameter name

reset-reason

Shut down (with reset-reason)

reset_reason_string

please enter reset_reason_string in quotes

Command Mode

  • /exec/configure/event-manager-applet

action overbudgetshut

[no] action <label> overbudgetshut [ module { <module> | <mod-str> } ]

Syntax Description

no

(Optional) Negate a command or set its defaults

action

Configure the actions to be executed

label

Enter the label <num1>[.<num2>] for action order num2 must be 0-9

overbudgetshut

Shut down the specified LCs due to power over budget

module

(Optional) Optional. Module to be force-shut(optional arg)

module

(Optional) please enter the module number

mod-str

(Optional) Enter the module number (integer value) or a $ prefixed parameter name

Command Mode

  • /exec/configure/event-manager-applet

action policy-default

action <label> policy-default

Syntax Description

action

Configure the actions to be executed

label

Enter the label <num1>[.<num2>] for action order num2 must be 0-9

policy-default

Do default action(s) of the policy being overridden

Command Mode

  • /exec/configure/event-manager-applet

action publish-event sub-system type

action <label> publish-event sub-system <sub-system-id> type <event-type> { [ arg1 <data1> ] [ arg2 <data2> ] [ arg3 <data3> ] [ arg4 <data4> ] }

Syntax Description

action

Configure the actions to be executed

label

Enter the label <num1>[.<num2>] for action order num2 must be 0-9

publish-event

Publish an application specific event

sub-system

Sub-system ID to which the application event belongs

sub-system-id

Sub-system ID value

type

Event type value

event-type

Event type value

arg1

(Optional) User specified data to be passed when the event is published

data1

(Optional) User specified data value

arg2

(Optional) User specified data to be passed when the event is published

data2

(Optional) User specified data value

arg3

(Optional) User specified data to be passed when the event is published

data3

(Optional) User specified data value

arg4

(Optional) User specified data to be passed when the event is published

data4

(Optional) User specified data value

Command Mode

  • /exec/configure/event-manager-applet

action reload

[no] action <label> reload [ module { <module> | <mod-str> } ]

Syntax Description

no

(Optional) Negate a command or set its defaults

action

Configure the actions to be executed

label

Enter the label <num1>[.<num2>] for action order num2 must be 0-9

reload

Reload the system or a specific module

module

(Optional) Reload a specific module

module

(Optional) please enter the module number

mod-str

(Optional) Enter the module number (integer value) or a $ prefixed parameter name

Command Mode

  • /exec/configure/event-manager-applet

action snmp-trap

action <label> snmp-trap [ intdata1 <integer-data1> ] [ intdata2 <integer-data2> ] [ strdata <string-data> ]

Syntax Description

action

Configure the actions to be executed

label

Enter the label <num1>[.<num2>] for action order num2 must be 0-9

snmp-trap

Send

intdata1

(Optional) Enter

integer-data1

(Optional) Integer

intdata2

(Optional) Enter

integer-data2

(Optional) Integer

strdata

(Optional) Enter

string-data

(Optional) String

Command Mode

  • /exec/configure/event-manager-applet

action syslog msg

action <label> syslog [ priority { <prio> | <prio-str> } ] msg <msg-text>

Syntax Description

action

Configure the actions to be executed

label

Enter the label <num1>[.<num2>] for action order num2 must be 0-9

syslog

Generate a syslog message

priority

(Optional) Priority of the syslog message

prio

(Optional) Enter the priority

prio-str

(Optional) Enter a valid $ prefixed name, for parameter substitution

msg

Enter the message for the syslog

msg-text

The message text

Command Mode

  • /exec/configure/event-manager-applet

activate

[no] activate

Syntax Description

no

(Optional) Negate a command or set its defaults

activate

Activate configured virtual service

Command Mode

  • /exec/configure/virt-serv

activate mode-100M

[no] activate mode-100M

Syntax Description

no

(Optional) Negate a command or set its defaults

activate

Activate new mode

mode-100M

Activate mode-100M

Command Mode

  • /exec/configure

activity-timer

{ [ no ] activity-timer <seconds> }

Syntax Description

no

(Optional) Negate a command or set its defaults

activity-timer

Number of seconds where a dynamic-EID is considered active

seconds

Timeout value in seconds

Command Mode

  • /exec/configure/lisp-dynamic-eid /exec/configure/vrf/lisp-dynamic-eid

add cli commands

add cli commands <filename>

Syntax Description

add

add

cli

cli

commands

commands

filename

filename

Command Mode

  • /exec

additional-paths install backup

[no] additional-paths install backup

Syntax Description

no

(Optional) Negate a command or set its defaults

additional-paths

Additional paths configuration

install

Install backup path

backup

Install backup path

Command Mode

  • /exec/configure/router-bgp/router-bgp-af-ipv6 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6 /exec/configure/router-bgp/router-bgp-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv4

additional-paths receive

[no] additional-paths receive

Syntax Description

no

(Optional) Negate a command or set its defaults

additional-paths

Additional paths configuration

receive

Additional paths Receive capability

Command Mode

  • /exec/configure/router-bgp/router-bgp-af /exec/configure/router-bgp/router-bgp-af-ipv4-mvpn /exec/configure/router-bgp/router-bgp-af-ipv6-mvpn /exec/configure/router-bgp/router-bgp-af-vpnv4 /exec/configure/router-bgp/router-bgp-af-vpnv6 /exec/configure/router-bgp/router-bgp-af-ipv4-label /exec/configure/router-bgp/router-bgp-af-ipv6-label /exec/configure/router-bgp/router-bgp-af-l2vpn-evpn

additional-paths selection route-map

[no] additional-paths selection route-map <rmap-name>

Syntax Description

no

(Optional) Negate a command or set its defaults

additional-paths

Additional paths configuration

selection

Additional paths selection

route-map

Route-map for additional paths selection

rmap-name

Route-map name

Command Mode

  • /exec/configure/router-bgp/router-bgp-af /exec/configure/router-bgp/router-bgp-af-vpnv4 /exec/configure/router-bgp/router-bgp-af-vpnv6 /exec/configure/router-bgp/router-bgp-af-ipv6-label /exec/configure/router-bgp/router-bgp-af-ipv4-mvpn /exec/configure/router-bgp/router-bgp-af-ipv6-mvpn /exec/configure/router-bgp/router-bgp-af-ipv4-label /exec/configure/router-bgp/router-bgp-af-l2vpn-evpn

additional-paths send

[no] additional-paths send

Syntax Description

no

(Optional) Negate a command or set its defaults

additional-paths

Additional paths configuration

send

Additional paths Send capability

Command Mode

  • /exec/configure/router-bgp/router-bgp-af /exec/configure/router-bgp/router-bgp-af-vpnv4 /exec/configure/router-bgp/router-bgp-af-vpnv6 /exec/configure/router-bgp/router-bgp-af-ipv6-label /exec/configure/router-bgp/router-bgp-af-ipv4-mvpn /exec/configure/router-bgp/router-bgp-af-ipv6-mvpn /exec/configure/router-bgp/router-bgp-af-ipv4-label /exec/configure/router-bgp/router-bgp-af-l2vpn-evpn

address-family ip address port

[no] { address-family | ip address } <ip4> port <portnum> [ protocol <proto> encoding <encoder> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Set destination IP address

ip

Set destination IPv4 address

address

IP address

port

Set destination port

protocol

(Optional) Set transport protocol

encoding

(Optional) Set encoding format

ip4

Destination IPv4 Address

portnum

Destination port

proto

(Optional)

encoder

(Optional)

Command Mode

  • /exec/configure/telemetry/destination-group

address-family ipv4 labeled-unicast

[no] address-family ipv4 labeled-unicast

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

ipv4

Configure IPv4 address-family

labeled-unicast

Configure labeled unicast sub-address-family

Command Mode

  • /exec/configure/router-bgp

address-family ipv4 labeled-unicast

{ [ no | default ] } address-family ipv4 labeled-unicast

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

address-family

Configure an address-family for peer

ipv4

Configure IPv4 address-family

labeled-unicast

Configure labeled unicast sub-address-family

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor /exec/configure/router-bgp/router-bgp-prefixneighbor

address-family ipv4 mdt

[no] address-family ipv4 mdt

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

ipv4

Configure IPv4 address-family

mdt

Configure Multicast Distribution Tree

Command Mode

  • /exec/configure/router-bgp

address-family ipv4 mdt

{ [ no | default ] } address-family ipv4 mdt

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

address-family

Configure an address-family

ipv4

Configure IPv4 address-family

mdt

Configure Multicast Distribution Tree

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor /exec/configure/router-bgp/router-bgp-prefixneighbor

address-family ipv4 mvpn

[no] address-family ipv4 mvpn

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

ipv4

Configure IPv4 address-family

mvpn

Configure Multicast VPN

Command Mode

  • /exec/configure/router-bgp

address-family ipv4 mvpn

{ [ no | default ] } address-family ipv4 mvpn

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

address-family

Configure an address-family

ipv4

Configure IPv4 address-family

mvpn

Configure Multicast VPN

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor /exec/configure/router-bgp/router-bgp-prefixneighbor

address-family ipv4 unicast

[no] address-family ipv4 { unicast | multicast }

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

ipv4

Configure IPv4 address-family

unicast

Configure unicast address-family

multicast

Configure multicast address-family

Command Mode

  • /exec/configure/router-bgp

address-family ipv4 unicast

[no] address-family ipv4 { unicast | multicast }

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

ipv4

Configure IPv4 address-family

unicast

Configure unicast address-family

multicast

Configure multicast address-family

Command Mode

  • /exec/configure/router-bgp/router-bgp-vrf

address-family ipv4 unicast

{ [ no | default ] } address-family ipv4 { unicast | multicast }

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

address-family

Configure an address-family for peer

ipv4

Configure IPv4 address-family

unicast

Configure Unicast sub-address-family

multicast

Configure Multicast sub-address-family

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor /exec/configure/router-bgp/router-bgp-prefixneighbor

address-family ipv4 unicast

[ no | default ] address-family ipv4 { unicast | multicast }

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

address-family

Configure an address-family for peer

ipv4

Configure IPv4 address-family

unicast

Configure Unicast sub-address-family

multicast

Configure Multicast sub-address-family

Command Mode

  • /exec/configure/router-bgp/router-bgp-vrf-neighbor /exec/configure/router-bgp/router-bgp-vrf-prefixneighbor

address-family ipv4 unicast

[no] { address-family ipv4 unicast }

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure Address Family and its parameters

ipv4

Configure IPv4 Address Family parameters

unicast

Unicast

Command Mode

  • /exec/configure/mpls_static

address-family ipv4 unicast

[no] address-family ipv4 unicast

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

ipv4

Configure IPv4 address-family

unicast

Configure unicast address-family

Command Mode

  • /exec/configure/router-eigrp/router-eigrp-vrf-common

address-family ipv4 unicast

[no] address-family ipv4 unicast

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure address family

ipv4

Configure IPv4 address family

unicast

Configure Unicast address family

Command Mode

  • /exec/configure/vrf

address-family ipv4 unicast

[no] address-family ipv4 unicast

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

ipv4

Configure IPv4 address-family

unicast

Configure unicast address-family

Command Mode

  • /exec/configure/router-isis/router-isis-vrf-common

address-family ipv4 unicast

[no] address-family ipv4 unicast

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

ipv4

Configure IPv4 address-family

unicast

Configure unicast address-family

Command Mode

  • /exec/configure/router-rip

address-family ipv4 unicast

[no] address-family ipv4 unicast

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

ipv4

Configure IPv4 address-family

unicast

Configure unicast address-family

Command Mode

  • /exec/configure/router-rip/router-rip-vrf

address-family ipv6 labeled-unicast

[no] address-family ipv6 labeled-unicast

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

ipv6

Configure IPv6 address-family

labeled-unicast

Configure labeled unicast sub-address-family

Command Mode

  • /exec/configure/router-bgp

address-family ipv6 labeled-unicast

{ [ no | default ] } address-family ipv6 labeled-unicast

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

address-family

Configure an address-family for peer

ipv6

Configure IPv6 address-family

labeled-unicast

Configure labeled unicast sub-address-family

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor /exec/configure/router-bgp/router-bgp-prefixneighbor

address-family ipv6 mvpn

[no] address-family ipv6 mvpn

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

ipv6

Configure IPv6 address-family

mvpn

Configure Multicast VPN

Command Mode

  • /exec/configure/router-bgp

address-family ipv6 mvpn

{ [ no | default ] } address-family ipv6 mvpn

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

address-family

Configure an address-family

ipv6

Configure IPv6 address-family

mvpn

Configure Multicast VPN

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor /exec/configure/router-bgp/router-bgp-prefixneighbor

address-family ipv6 unicast

[no] address-family ipv6 { unicast | multicast }

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

ipv6

Configure IPv6 address-family

unicast

Configure unicast address-family

multicast

Configure multicast address-family

Command Mode

  • /exec/configure/router-bgp

address-family ipv6 unicast

[no] address-family ipv6 { unicast | multicast }

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

ipv6

Configure IPv6 address-family

unicast

Configure unicast address-family

multicast

Configure multicast address-family

Command Mode

  • /exec/configure/router-bgp/router-bgp-vrf

address-family ipv6 unicast

{ [ no | default ] } address-family ipv6 { unicast | multicast }

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

address-family

Configure an address-family for peer

ipv6

Configure IPv6 address-family

unicast

Configure Unicast sub-address-family

multicast

Configure Multicast sub-address-family

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor /exec/configure/router-bgp/router-bgp-prefixneighbor

address-family ipv6 unicast

[ no | default ] address-family ipv6 { unicast | multicast }

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

address-family

Configure an address-family for peer

ipv6

Configure IPv6 address-family

unicast

Configure Unicast sub-address-family

multicast

Configure Multicast sub-address-family

Command Mode

  • /exec/configure/router-bgp/router-bgp-vrf-neighbor /exec/configure/router-bgp/router-bgp-vrf-prefixneighbor

address-family ipv6 unicast

[no] { address-family ipv6 unicast }

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure Address Family and its parameters

ipv6

Configure IPv6 Address Family parameters

unicast

Unicast

Command Mode

  • /exec/configure/mpls_static

address-family ipv6 unicast

[no] address-family ipv6 unicast

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

ipv6

Configure IPv6 address-family

unicast

Configure unicast address-family

Command Mode

  • /exec/configure/router-eigrp/router-eigrp-vrf-common

address-family ipv6 unicast

[no] address-family ipv6 unicast

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure address family

ipv6

Configure IPv6 address family

unicast

Configure Unicast address family

Command Mode

  • /exec/configure/vrf

address-family ipv6 unicast

[no] address-family ipv6 unicast

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

ipv6

Configure IPv6 address-family

unicast

Configure unicast address-family

Command Mode

  • /exec/configure/router-isis/router-isis-vrf-common

address-family ipv6 unicast

[no] address-family ipv6 unicast

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

ipv6

Configure IPv6 address-family

unicast

Configure unicast address-family

Command Mode

  • /exec/configure/router-rip

address-family ipv6 unicast

[no] address-family ipv6 unicast

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

ipv6

Configure IPv6 address-family

unicast

Configure unicast address-family

Command Mode

  • /exec/configure/router-rip/router-rip-vrf

address-family ipv6 unicast

[no] address-family ipv6 unicast

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

ipv6

Configure IPv6 address-family

unicast

Configure IPv6 unicast address-family

Command Mode

  • /exec/configure/router-ospf3

address-family ipv6 unicast

[no] address-family ipv6 unicast

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

ipv6

Configure IPv6 address-family

unicast

Configure IPv6 unicast address-family

Command Mode

  • /exec/configure/router-ospf3/vrf

address-family l2vpn evpn

[no] address-family l2vpn evpn

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

l2vpn

Configure L2VPN address-family

evpn

Configure L2VPN EVPN address-family

Command Mode

  • /exec/configure/router-bgp

address-family l2vpn evpn

{ [ no | default ] } address-family l2vpn evpn

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

address-family

Configure an address-family

l2vpn

Configure L2VPN address-family

evpn

Configure L2VPN EVPN address-family

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor /exec/configure/router-bgp/router-bgp-prefixneighbor

address-family l2vpn vpls

[no] address-family l2vpn vpls

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

l2vpn

Configure L2VPN address-family

vpls

Configure L2VPN VPLS address-family

Command Mode

  • /exec/configure/router-bgp

address-family l2vpn vpls

{ [ no | default ] } address-family l2vpn vpls

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

address-family

Configure an address-family

l2vpn

Configure L2VPN address-family

vpls

Configure L2VPN VPLS address-family

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor /exec/configure/router-bgp/router-bgp-prefixneighbor

address-family link-state

[no] address-family link-state

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

link-state

Configure link-state address-family

Command Mode

  • /exec/configure/router-bgp

address-family link-state

{ [ no | default ] } address-family link-state

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

address-family

Configure an address-family

link-state

Configure link-state address-family

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor /exec/configure/router-bgp/router-bgp-prefixneighbor

address-family vpnv4 unicast

[no] address-family vpnv4 unicast

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

vpnv4

Configure IPv4 VPN address-family

unicast

Configure Unicast sub-address-family

Command Mode

  • /exec/configure/router-bgp

address-family vpnv4 unicast

{ [ no | default ] } address-family vpnv4 unicast

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

address-family

Configure an address-family for peer

vpnv4

Configure IPv4 VPN address-family

unicast

Configure Unicast sub-address-family

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor /exec/configure/router-bgp/router-bgp-prefixneighbor

address-family vpnv6 unicast

[no] address-family vpnv6 unicast

Syntax Description

no

(Optional) Negate a command or set its defaults

address-family

Configure an address-family

vpnv6

Configure IPv6 VPN address-family

unicast

Configure Unicast sub-address-family

Command Mode

  • /exec/configure/router-bgp

address-family vpnv6 unicast

{ [ no | default ] } address-family vpnv6 unicast

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

address-family

Configure an address-family for peer

vpnv6

Configure IPv6 VPN address-family

unicast

Configure Unicast sub-address-family

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor /exec/configure/router-bgp/router-bgp-prefixneighbor

address

[no] address <ip_addr> [ primary ]

Syntax Description

no

(Optional) Negate a command or set its defaults

address

IP Address

primary

(Optional) Primary Address

ip_addr

IPv4 Address

Command Mode

  • /exec/configure/if-eth-any/vrrpv3_ipv4

address

[no] address <ipv6_addr>

Syntax Description

no

(Optional) Negate a command or set its defaults

address

IP Address

Command Mode

  • /exec/configure/if-eth-any/vrrpv3_ipv6

address

[no] address <ip_addr>

Syntax Description

no

(Optional) Negate a command or set its defaults

address

IP Address configuration

ip_addr

IP Address

Command Mode

  • /exec/configure/if-eth-any/vrrs

address

[no] address <ipv6_addr>

Syntax Description

no

(Optional) Negate a command or set its defaults

address

IP Address configuration

Command Mode

  • /exec/configure/if-eth-any/vrrs

address

{ address <ip_address> | no address [ <ip_address> ] }

Syntax Description

no

Negate a command or set its defaults

address

Add an IP address to the vr

ip_address

ip address

Command Mode

  • /exec/configure/if-eth-any/vrrp

address

[no] address <start-ip> <end-ip>

Syntax Description

no

(Optional) Negate a command or set its defaults

address

Address range for the pool

start-ip

Start IP address

end-ip

End IP address

Command Mode

  • /exec/configure/ipnat-pool

address port-number

address { <ipv4-addr> | <ipv6-addr> } port-number <port-number> | no address

Syntax Description

no

Negate a command or set its defaults

address

Configure IPv4 or IPv6 address

ipv4-addr

IPv4 address of the BMP server

port-number

Configure the port for the BMP server

port-number

Port number value

Command Mode

  • /exec/configure/router-bgp/router-bgp-bmp-server

address primary

[no] address <ipv6_addr> primary

Syntax Description

no

(Optional) Negate a command or set its defaults

address

IP Address

primary

Primary Address

Command Mode

  • /exec/configure/if-eth-any/vrrpv3_ipv6

address secondary

[no] address <ip_addr> secondary

Syntax Description

no

(Optional) Negate a command or set its defaults

address

IP Address

secondary

Secondary Address

ip_addr

IPv4 Address

Command Mode

  • /exec/configure/if-eth-any/vrrpv3_ipv4

address secondary

{ address <ip_address> secondary | no address <ip_address> secondary }

Syntax Description

no

Negate a command or set its defaults

address

Add an IP address to the vr

ip_address

ip address

secondary

a virtual IP address without owner

Command Mode

  • /exec/configure/if-eth-any/vrrp

adjacency-check

[no] adjacency-check

Syntax Description

no

(Optional) Negate a command or set its defaults

adjacency-check

Adjacency's protocol support consistency check

Command Mode

  • /exec/configure/router-isis/router-isis-af-common

adjacency-resolve

[no] adjacency-resolve

Syntax Description

no

(Optional) Negate a command or set its defaults

adjacency-resolve

Resolve L3->L2 address for ISIS adjacency

Command Mode

  • /exec/configure/router-isis

advertise-labels

[no] advertise-labels [ vrf { <vrf-name> | <vrf-known-name> } ] [ [ for <pfx-list> [ to <peer-pfx-list> ] ] | [ interface <intf> ] ]

Syntax Description

no

(Optional) Negate a command or set its defaults

advertise-labels

Label advertisements

vrf

(Optional) VRF Routing/Forwarding instance information

vrf-name

(Optional) VPN Routing/Forwarding instance name

vrf-known-name

(Optional) Known VRF name

for

(Optional) Prefix list specifying controls on destination prefixes

pfx-list

(Optional) Name of prefix list

to

(Optional) Prefix list specifying controls on LDP peers

peer-pfx-list

(Optional) Name of prefix list

interface

(Optional) Advertise /32 interface address

intf

(Optional)

Command Mode

  • /exec/configure/ldp

advertise-map exist default advertise-map

{ [ no ] advertise-map <advt-rmap-name> { exist-map | non-exist-map } <cond-rmap-name> } | default advertise-map

Syntax Description

no

(Optional) Negate a command or set its defaults

default

Inherit values from a peer template

advertise-map

Specify route-map for conditional advertisement

exist-map

Condition route-map to advertise only when prefix in condition exists

non-exist-map

Condition route-map to advertise only when prefix in condition does not exist

advt-rmap-name

Route-map name

cond-rmap-name

Route-map name

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label

advertise-pip

[no] advertise-pip

Syntax Description

no

(Optional) Negate a command or set its defaults

advertise-pip

advertise physical ip for type-5 route

Command Mode

  • /exec/configure/router-bgp/router-bgp-af-l2vpn-evpn

advertise-system-mac

[no] advertise-system-mac

Syntax Description

no

(Optional) Negate a command or set its defaults

advertise-system-mac

Advertise extra EVPN RT-2 with system MAC

Command Mode

  • /exec/configure/router-bgp/router-bgp-af-l2vpn-evpn

advertise evpn multicast

[no] advertise evpn multicast

Syntax Description

no

(Optional) Negate a command or set its defaults

advertise

Advertise L2 multicast capability

evpn

evpn

multicast

L2 multicast

Command Mode

  • /exec/configure

advertise l2vpn evpn

[no] advertise l2vpn evpn

Syntax Description

no

(Optional) Negate a command or set its defaults

advertise

Configure advertise for this AF

l2vpn

L2VPN

evpn

EVPN

Command Mode

  • /exec/configure/router-bgp/router-bgp-vrf-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6

advertise virtual-rmac

[no] advertise virtual-rmac

Syntax Description

no

(Optional) Negate a command or set its defaults

advertise

Reachability advertisement

virtual-rmac

Advertise virtual RMAC capability

Command Mode

  • /exec/configure/if-nve

advertisement-interval

[no] advertisement-interval <adv-sec>

Syntax Description

no

(Optional) Negate a command or set its defaults

advertisement-interval

Minimum interval between sending BGP routing updates

adv-sec

Time in seconds

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4 /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6

advertisement-interval

{ advertisement-interval <interval_time> | no advertisement-interval [ <interval_time> ] }

Syntax Description

no

Negate a command or set its defaults

advertisement-interval

Set the time interval between advertisement

interval_time

Time interval (in seconds) between advertisements

Command Mode

  • /exec/configure/if-eth-any/vrrp

afd queue-desired

[no] afd queue-desired <q-desired> { bytes | kbytes | mbytes } [ ecn ]

Syntax Description

no

(Optional) Negate a command or set its defaults

afd

Configure AFD parameters

queue-desired

Specify Queue Desired for AFD

bytes

Bytes

kbytes

Kilo bytes

mbytes

Mega bytes

ecn

(Optional) ECN

Command Mode

  • /exec/configure/policy-map/type/queuing/class

affinity-group

{ affinity-group <affinity_group_id> } | { { no | default } affinity-group [ <affinity_group_id> ] }

Syntax Description

no

Negate a command or set its defaults

default

Inherit values from a peer template

affinity-group

Configure an affinity group

affinity_group_id

Affinity Group ID

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor-sess

affinity-group activate

affinity-group activate <affinity_group_id> | no affinity-group activate [ <affinity_group_id> ]

Syntax Description

no

Negate a command or set its defaults

affinity-group

Configure an affinity group

activate

Activate the affinity group

affinity_group_id

AFFINITY Group ID

Command Mode

  • /exec/configure/router-bgp

affinity

[no] affinity | affinity <hex_value> [ mask <mask_value> ]

Syntax Description

no

Negate a command or set its defaults

affinity

Specify attribute flags for links comprising LSP

hex_value

affinity value

mask

(Optional) mask on desired link attributes

mask_value

(Optional) affinity mask value

Command Mode

  • /exec/configure/te/lsp-attr

affinity

[no] affinity | affinity <value> [ mask <mask-value> ]

Syntax Description

no

Negate a command or set its defaults

affinity

desired link attributes for links comprising tunnel

value

affinity value

mask

(Optional) mask on desired link attributes

mask-value

(Optional) affinity mask value

Command Mode

  • /exec/configure/if-te /exec/configure/tunnel-te/cbts-member

aggregate-address

[no] aggregate-address { <ip-addr> <ip-mask> | <ip-prefix> } [ as-set | summary-only | suppress-map <suppress-rmap> | advertise-map <advertise-rmap> | attribute-map <attribute-rmap> ] +

Syntax Description

no

(Optional) Negate a command or set its defaults

aggregate-address

Configure BGP aggregate prefixes

ip-addr

Aggregate address

ip-mask

Aggregate mask

ip-prefix

Aggregate prefix

summary-only

(Optional) Don't advertise more specifics

as-set

(Optional) Generate AS-SET information

suppress-map

(Optional) Conditionally filter more specific routes

advertise-map

(Optional) Select attribute information from specific routes

attribute-map

(Optional) Set attribute information of aggregate

advertise-rmap

(Optional) Route-map name

suppress-rmap

(Optional) Route-map name

attribute-rmap

(Optional) Route-map name

Command Mode

  • /exec/configure/router-bgp/router-bgp-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv4

aggregate-address

[no] aggregate-address <ipv6-prefix> [ as-set | summary-only | suppress-map <suppress-rmap> | advertise-map <advertise-rmap> | attribute-map <attribute-rmap> ] +

Syntax Description

no

(Optional) Negate a command or set its defaults

aggregate-address

Configure BGP aggregate IPv6 prefixes

as-set

(Optional) Generate AS-SET information

summary-only

(Optional) Don't advertise more specifics

suppress-map

(Optional) Conditionally filter more specific routes

advertise-map

(Optional) Select attribute information from specific routes

attribute-map

(Optional) Set attribute information of aggregate

advertise-rmap

(Optional) Route-map name

suppress-rmap

(Optional) Route-map name

attribute-rmap

(Optional) Route-map name

Command Mode

  • /exec/configure/router-bgp/router-bgp-af-ipv6 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6

alert-group user-def-cmd

[no] alert-group { Configuration | Diagnostic | Environmental | Inventory | License | Linecard-Hardware | Supervisor-Hardware | Syslog-group-port | System | Test } user-def-cmd <s0>

Syntax Description

no

(Optional) Negate a command or set its defaults

alert-group

alert group

user-def-cmd

configure a cli command for an alert group

s0

A valid CLI command

Environmental

Power,fan,temperature related events

Inventory

Inventory status events

License

Events related to licensing

Linecard-Hardware

Linecard related events

Supervisor-Hardware

Supervisor related events

Syslog-group-port

Events related to syslog messages filed by port manager

System

Software related events

Test

User generated test events

Configuration

Events related to Configuration

Diagnostic

Events related to Diagnostic

Command Mode

  • /exec/configure/callhome

allocate-label all

[no] allocate-label { all | route-map <rmap-name> }

Syntax Description

no

(Optional) Negate a command or set its defaults

allocate-label

Configure label allocation for this AF

all

Allocate labels for all routes

route-map

Allocate labels for selected routes

rmap-name

Route-map name

Command Mode

  • /exec/configure/router-bgp/router-bgp-vrf-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6 /exec/configure/router-bgp/router-bgp-af-ipv6 /exec/configure/router-bgp/router-bgp-af-ipv4

allocate-label option-b

[no] allocate-label option-b

Syntax Description

no

(Optional) Negate a command or set its defaults

allocate-label

Allow allocation of labels

option-b

Allow allocation of option B labels

Command Mode

  • /exec/configure/router-bgp/router-bgp-af-vpnv4 /exec/configure/router-bgp/router-bgp-af-vpnv6

allocate1 interface2

allocate1 interface2 { <interface-id> [ force ] | unallocated-interfaces }

Syntax Description

allocate1

Assign interfaces to vdc

interface2

Assign interface range to vdc

interface-id

Assign interface range to vdc

force

(Optional) force

unallocated-interfaces

Best-effort trying to move all interfaces in the unallocated pool into this vdc

Command Mode

  • /exec/configure/vdc

allocate2 fcoe-vlan-range

{ allocate2 fcoe-vlan-range [ <vlan_range> ] [ from vdcs <vdc_names> ] } | { no allocate2 fcoe-vlan-range [ <vlan_range> | { from vdcs <vdc_names> } ] }

Syntax Description

no

Negate a command or set its defaults

allocate2

Assign interfaces to vdc

fcoe-vlan-range

vlans reserved for FCoE

vlan_range

(Optional) vlans reserved for FCoE

from

(Optional) which vdcs will be sharing ports with the FCoE vdc

vdcs

(Optional) which vdcs will be sharing ports with the FCoE vdc

vdc_names

(Optional) which vdcs will be sharing porst with the FCoE vdc

Command Mode

  • /exec/configure/vdc

allocate3 shared interface3

[no] allocate3 shared interface3 <sinterface-id>

Syntax Description

no

(Optional) Negate a command or set its defaults

allocate3

Assign interfaces to vdc

interface3

Assign interface range to vdc

sinterface-id

Assign interface range to vdc

shared

Shared this port using the reserved FCoE vlans

Command Mode

  • /exec/configure/vdc

allow-vni-in-ethertag

[no] allow-vni-in-ethertag

Syntax Description

no

(Optional) Negate a command or set its defaults

allow-vni-in-ethertag

Allow VNI in Ethernet Tag field in EVPN route

Command Mode

  • /exec/configure/router-bgp/router-bgp-af-l2vpn-evpn

allow delete boot-image

[no] allow delete boot-image [ retain ]

Syntax Description

no

(Optional) Negate a command or set its defaults

allow

allow kickstart or system image to be deleted

delete

allow delete or overwrite of image file

boot-image

image file

retain

(Optional) retain this command after reboot

Command Mode

  • /exec

allow feature-set

[no] allow feature-set <fs>

Syntax Description

no

(Optional) Negate a command or set its defaults

allow

Used to change permisions inside a vdc

feature-set

Change which feature-sets the user is able to enable inside the vdc

fs

installed feature-sets

Command Mode

  • /exec/configure/vdc

allowas-in

[ no | default ] allowas-in [ <allowas-in-cnt> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

allowas-in

Accept as-path with my AS present in it

allowas-in-cnt

(Optional) Number of occurrences of AS number, default is 3

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4 /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6 /exec/configure/router-bgp/router-bgp-vrf-neighbor/router-bgp-vrf-neighbor-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-neighbor/router-bgp-vrf-neighbor-af-ipv6 /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-link-state /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn

allowas-in

[ no | default ] allowas-in [ <allowas-in-cnt> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

allowas-in

Accept as-path with my AS present in it

allowas-in-cnt

(Optional) Number of occurrences of AS number, default is 3

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-vpls

allowed-locators

{ [ no ] allowed-locators { <rloc> | <rloc6> } + }

Syntax Description

no

(Optional) Negate a command or set its defaults

allowed-locators

List of locators from LISP site

rloc

IPv4 locator allowed in registered locator-set

Command Mode

  • /exec/configure/lisp-site /exec/configure/vrf/lisp-site

allowed-vlans

allowed-vlans { <allow-vlans> | add <add-vlans> | except <except-vlans> | remove <remove-vlans> | all }

Syntax Description

allowed-vlans

Set list of allowed vlans that can be used for interface configuration

allow-vlans

VLAN ID 1-4094 or range(s) like: 1-5, 10 or 2-5,7-19

add

add VLANs to the current list

add-vlans

VLAN ID 1-4094 or range(s) like: 1-5, 10 or 2-5,7-19

except

all VLANs except the following

except-vlans

VLAN ID 1-4094 or range(s) like: 1-5, 10 or 2-5,7-19

remove

remove VLANs from the current list

remove-vlans

VLAN ID 1-4094 or range(s) like: 1-5, 10 or 2-5,7-19

all

all VLANs

Command Mode

  • /exec/configure/vmt-conn

amt flush-routes

[no] amt flush-routes

Syntax Description

no

(Optional) Negate a command or set its defaults

amt

AMT global configuration commands

flush-routes

Remove routes when restarting AMT

Command Mode

  • /exec/configure /exec/configure/vrf

amt pseudo-interface

{ { amt pseudo-interface <interface> } | { no amt pseudo-interface [ <interface> ] } }

Syntax Description

no

Negate a command or set its defaults

amt

AMT global configuration commands

pseudo-interface

Tunnel to relay for forwarding IGMP/MLD messages

interface

Intername name to used for AMT pseudo interface

Command Mode

  • /exec/configure /exec/configure/vrf

analytics cluster

[no] analytics cluster <clustername> [ vrf <vrfName> ] [ srcIf <src_intf> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

analytics

Feature Analytics

cluster

Analytics cluster

clustername

Cluster name

vrf

(Optional) VRF Name

vrfName

(Optional) VRF name

srcIf

(Optional) Source Interface

src_intf

(Optional) Source Interface

Command Mode

  • /exec/configure

anonymous-id

{ [ no ] anonymous-id <id> }

Syntax Description

anonymous-id

anonymous identity associated with this profile

id

identity name

Command Mode

  • /exec/configure/dot1x-cred

append-after next

append-after <index> { next-address [ loose | strict ] <ipaddr> | exclude-address <ipaddr> }

Syntax Description

append-after

Append additional entry after specified index

index

Previous index number

next-address

Specify the next address in the path

loose

(Optional) Target address is loose

strict

(Optional) Target address is strict

exclude-address

Exclude an address from subsequent partial path segments

ipaddr

Enter IP address (A.B.C.D)

Command Mode

  • /exec/configure/te/expl-path

apply profile

[no] apply profile { <all_conf_profile_name> } [ include-profile <include-profile> ] [ { param-instance <plistinst> | include-instance <plistinst> } + ]

Syntax Description

no

(Optional) Negate a command or set its defaults

apply

Apply a config-profile

profile

Apply a config-profile

all_conf_profile_name

Enter the name of the profile

param-instance

(Optional) Enter the name of the param-instance

plistinst

(Optional) Enter the name of the instance

include-profile

(Optional) Enter the name of the include profile

include-profile

(Optional) Enter the name of the include profile

include-instance

(Optional) Enter the param-instance corresponding to the first included profile

plistinst

(Optional) Enter the name of the include instance

Command Mode

  • /exec/configure

area authentication

[no] area <area-id-ip> authentication [ message-digest ]

Syntax Description

no

(Optional) Negate a command or set its defaults

area

Configure area properties

area-id-ip

Area Id as an integer or ip address

authentication

Enable authentication for the area

message-digest

(Optional) Use message-digest authentication

Command Mode

  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

area authentication

area <area-id-ip> authentication { disable | ipsec spi <spi_id> { md5 <akey> | sha1 <akey> } } | no area <area-id-ip> authentication { disable | ipsec spi <spi_id> }

Syntax Description

no

Negate a command or set its defaults

area

Configure area properties

area-id-ip

Area Id as an integer or ip address

authentication

Enable Authentication

disable

Disable Authentication

ipsec

IPSec

spi

Security Parameter Index

spi_id

SPI Value

md5

Use the MD5 algorithim

akey

Authentication Key

sha1

Use the SHA1 algorithim

akey

Authentication Key

Command Mode

  • /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf

area default-cost

{ { area <area-id-ip> default-cost <cost> } | { no area <area-id-ip> default-cost [ <cost> ] } }

Syntax Description

no

Negate a command or set its defaults

area

Configure area properties

area-id-ip

Area Id as an integer or ip address

default-cost

Specify default-cost for default summary LSA

cost

Cost value

Command Mode

  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

area default-cost

{ { area <area-id-ip> default-cost <cost> } | { no area <area-id-ip> default-cost [ <cost> ] } }

Syntax Description

no

Negate a command or set its defaults

area

Configure area properties

area-id-ip

Area Id as an integer or ip address

default-cost

Specify default-cost for default inter-area-prefix LSA

cost

Cost value

Command Mode

  • /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6

area filter-list route-map in

{ area <area-id-ip> filter-list route-map { <policy-name> | <rtr_pol_name> } { in | out } } | { no area <area-id-ip> filter-list route-map { <policy-name> | <rtr_pol_name> } [ in | out ] }

Syntax Description

no

Negate a command or set its defaults

area

Configure area properties

area-id-ip

Area Id as an integer or ip address

filter-list

Filter prefixes between OSPF areas

route-map

Name of filter policy

policy-name

Route-map name

rtr_pol_name

An existing routing-rules policy

in

Filter networks sent to this area

out

Filter networks sent from this area

Command Mode

  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

area filter-list route-map in

{ area <area-id-ip> filter-list route-map { <policy-name> | <rtr_pol_name> } { in | out } } | { no area <area-id-ip> filter-list route-map { <policy-name> | <rtr_pol_name> } [ in | out ] }

Syntax Description

no

Negate a command or set its defaults

area

Configure area properties

area-id-ip

Area Id as an integer or ip address

filter-list

Filter prefixes between OSPF areas

route-map

Name of filter policy

policy-name

Route-map name

rtr_pol_name

An existing routing-rules policy

in

Filter networks sent to this area

out

Filter networks sent from this area

Command Mode

  • /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6

area nssa

[no] area <area-id-ip> nssa { [ no-summary ] [ no-redistribution ] [ default-information-originate [ route-map <policy-name> ] ] } +

Syntax Description

no

(Optional) Negate a command or set its defaults

area

Configure area properties

area-id-ip

Area Id as an integer or ip address

nssa

Configure area as NSSA

no-summary

(Optional) Do not send summary LSAs into NSSA area

no-redistribution

(Optional) Do not send redistributed LSAs into NSSA area

default-information-originate

(Optional) Originate Type-7 default LSA into NSSA area

route-map

(Optional) Policy to control distribution of default route

policy-name

(Optional) Route-map name

Command Mode

  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

area nssa

[no] area <area-id-ip> nssa { [ no-summary ] [ no-redistribution ] [ default-information-originate [ route-map <policy-name> ] ] } +

Syntax Description

no

(Optional) Negate a command or set its defaults

area

Configure area properties

area-id-ip

Area Id as an integer or ip address

nssa

Configure area as NSSA

no-summary

(Optional) Do not send summary LSAs into NSSA area

no-redistribution

(Optional) Do not send redistributed LSAs into NSSA area

default-information-originate

(Optional) Originate Type-7 default LSA into NSSA area

route-map

(Optional) Policy to control distribution of default route

policy-name

(Optional) Route-map name

Command Mode

  • /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf

area nssa translate type7 always never supress-fa

{ area <area-id-ip> nssa translate type7 { always [ supress-fa ] | never | supress-fa } } | { no area <area-id-ip> nssa translate type7 [ always [ supress-fa ] | never | supress-fa ] }

Syntax Description

no

Negate a command or set its defaults

area

Configure area properties

area-id-ip

Area Id as an integer or ip address

nssa

Configure area as NSSA

translate

Translate LSA

type7

From Type 7 to Type 5

always

Always translate LSAs

never

Never translate LSAs

supress-fa

(Optional) Supress forwarding address in translated LSAs

Command Mode

  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

area nssa translate type7 always never supress-fa

{ area <area-id-ip> nssa translate type7 { always [ supress-fa ] | never | supress-fa } } | { no area <area-id-ip> nssa translate type7 [ always [ supress-fa ] | never | supress-fa ] }

Syntax Description

no

Negate a command or set its defaults

area

Configure area properties

area-id-ip

Area Id as an integer or ip address

nssa

Configure area as NSSA

translate

Translate LSA

type7

From NSSA-external (Type 7) to AS-external (Type 5)

always

Always translate LSAs

never

Never translate LSAs

supress-fa

(Optional) Supress forwarding address in translated LSAs

Command Mode

  • /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf

area range

[no] area <area-id-ip> range { <ip-dest> <ip-mask> | <ip-prefix> } { [ not-advertise ] [ cost <conf-cost> ] } +

Syntax Description

no

(Optional) Negate a command or set its defaults

area

Configure area properties

area-id-ip

Area Id as an integer or ip address

range

Configure an address range for an area

ip-dest

IP prefix format: i.i.i.i

ip-mask

IP network mask format: m.m.m.m

ip-prefix

IP prefix format: x.x.x.x/ml

not-advertise

(Optional) Suppress advertising the specified range

cost

(Optional) Cost to use for range

conf-cost

(Optional) Cost value

Command Mode

  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

area range

[no] area <area-id-ip> range <ipv6-prefix> { [ not-advertise ] [ cost <conf-cost> ] } +

Syntax Description

no

(Optional) Negate a command or set its defaults

area

Configure area properties

area-id-ip

Area Id as an integer or ip address

range

Configure an address range for an area

not-advertise

(Optional) Suppress advertising the specified range

cost

(Optional) Cost to use for range

conf-cost

(Optional) Cost value

Command Mode

  • /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6

area sham-link

[no] area <area-id-ip> sham-link <source-address> <dest-address>

Syntax Description

no

(Optional) Negate a command or set its defaults

area

Configure area properties

area-id-ip

Area Id as an integer or ip address

sham-link

Define a sham link and its parameters

source-address

IP addr associated with sham-link source

dest-address

IP addr associated with sham-link destination

Command Mode

  • /exec/configure/router-ospf/vrf

area stub

[no] area <area-id-ip> stub [ no-summary ]

Syntax Description

no

(Optional) Negate a command or set its defaults

area

Configure area properties

area-id-ip

Area Id as an integer or ip address

stub

Configure area as a stub

no-summary

(Optional) Prevent ABR from sending summary LSAs into stub area

Command Mode

  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

area stub

[no] area <area-id-ip> stub [ no-summary ]

Syntax Description

no

(Optional) Negate a command or set its defaults

area

Configure area properties

area-id-ip

Area Id as an integer or ip address

stub

Configure area as a stub

no-summary

(Optional) Prevent ABR from sending summary LSAs into stub area

Command Mode

  • /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf

area virtual-link

[no] area <area-id-ip> virtual-link <routerid>

Syntax Description

no

(Optional) Negate a command or set its defaults

area

Configure area properties

area-id-ip

Area Id as an integer or ip address

virtual-link

Define a virtual link and its parameters

routerid

Router ID associated with virtual link neighbor

Command Mode

  • /exec/configure/router-ospf

area virtual-link

[no] area <area-id-ip> virtual-link <routerid>

Syntax Description

no

(Optional) Negate a command or set its defaults

area

Configure area properties

area-id-ip

Area Id as an integer or ip address

virtual-link

Define a virtual link and its parameters

routerid

Router ID associated with virtual link neighbor

Command Mode

  • /exec/configure/router-ospf/vrf

area virtual-link

[no] area <area-id-ip> virtual-link <routerid>

Syntax Description

no

(Optional) Negate a command or set its defaults

area

Configure area properties

area-id-ip

Area Id as an integer or ip address

virtual-link

Define a virtual link and its parameters

routerid

Router ID associated with virtual link neighbor

Command Mode

  • /exec/configure/router-ospf3

area virtual-link

[no] area <area-id-ip> virtual-link <routerid>

Syntax Description

no

(Optional) Negate a command or set its defaults

area

Configure area properties

area-id-ip

Area Id as an integer or ip address

virtual-link

Define a virtual link and its parameters

routerid

Router ID associated with virtual link neighbor

Command Mode

  • /exec/configure/router-ospf3/vrf

arp access-list

[no] arp access-list <name>

Syntax Description

no

(Optional) Negate a command or set its defaults

arp

ARP access-list configuration commands

access-list

Configure access list

name

List name

Command Mode

  • /exec/configure

as-format asdot

as-format asdot | no as-format

Syntax Description

no

Negate a command or set its defaults

as-format

Configure the router's Autonomous system number (ASN) notation

asdot

Specifies the Autonomous system number (ASN) notation to asdot format

Command Mode

  • /exec/configure

as-override

[ no | default ] as-override

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

as-override

Override matching AS-number while sending update

Command Mode

  • /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af /exec/configure/router-bgp/router-bgp-vrf-neighbor/router-bgp-vrf-neighbor-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-neighbor/router-bgp-vrf-neighbor-af-ipv6 /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label

attach console module

attach console module <module>

Syntax Description

attach

Connect to a specific linecard

console

Connect to the console

module

Connect to the module console

module

Enter module number

Command Mode

  • /exec

attach module

attach module <module>

Syntax Description

attach

Connect to a specific linecard

module

Module number of the linecard

module

Enter module number

Command Mode

  • /exec

attach module node

attach module <module> node <i0>

Syntax Description

attach

Connect to a specific linecard

module

Module number of the linecard

module

Enter module number

node

Avanti node number on the linecard

i0

Command Mode

  • /exec

attach module port

attach module <module> port <i0>

Syntax Description

attach

Connect to a specific linecard

module

Module number of the linecard

module

Enter module number

port

Port number on the linecard

i0

Command Mode

  • /exec

auth-mechanism plain

[no] auth-mechanism { plain }

Syntax Description

no

(Optional) Negate a command or set its defaults

auth-mechanism

Set the authentication mechanism

plain

Set the authentication mechanism as plain(default)

Command Mode

  • /exec/configure/ldap

authentication-check

[no] authentication-check

Syntax Description

no

(Optional) Negate a command or set its defaults

authentication-check

Check authentication on received LSP/CSNP/PSNP's

Command Mode

  • /exec/configure/otv-isis/otv-isis-vrf-common

authentication-check level-1

[no] authentication-check level-1

Syntax Description

no

(Optional) Negate a command or set its defaults

authentication-check

Check authentication on received LSP/CSNP/PSNP's

level-1

Specify authentication check for level-1 LSP, CSNP and PSNP

Command Mode

  • /exec/configure/router-isis/router-isis-vrf-common

authentication-check level-2

[no] authentication-check level-2

Syntax Description

no

(Optional) Negate a command or set its defaults

authentication-check

Check authentication on received LSP/CSNP/PSNP's

level-2

Specify authentication check for level-2 LSP, CSNP and PSNP

Command Mode

  • /exec/configure/router-isis/router-isis-vrf-common

authentication-key

{ { authentication-key <key> } | { no authentication-key [ <key> ] } }

Syntax Description

no

Negate a command or set its defaults

authentication-key

Configure the authentication key for the virtual-link

key

Authentication key

Command Mode

  • /exec/configure/router-ospf/router-ospf-vlink /exec/configure/router-ospf/vrf/router-ospf-vlink

authentication-key

{ { authentication-key <key> } | { no authentication-key [ <key> ] } }

Syntax Description

no

Negate a command or set its defaults

authentication-key

Configure the authentication key for the sham-link

key

Authentication key

Command Mode

  • /exec/configure/router-ospf/vrf/router-ospf-slink

authentication-key

{ [ no ] authentication-key <key> }

Syntax Description

no

(Optional) Negate a command or set its defaults

authentication-key

Authentication key used by LISP site

key

SHA-1 password

Command Mode

  • /exec/configure/lisp-site /exec/configure/vrf/lisp-site

authentication-type cleartext

{ authentication-type { cleartext | md5 } | no authentication-type [ { cleartext | md5 } ] }

Syntax Description

no

Negate a command or set its defaults

authentication-type

Set authentication type

cleartext

Cleartext

md5

HMAC-MD5

Command Mode

  • /exec/configure/otv-isis/otv-isis-vrf-common

authentication-type cleartext

{ authentication-type { cleartext | md5 } <level> | no authentication-type [ { cleartext | md5 } ] <level> }

Syntax Description

no

Negate a command or set its defaults

authentication-type

Set authentication type

cleartext

Cleartext

md5

HMAC-MD5

level

IS-IS level

Command Mode

  • /exec/configure/router-isis/router-isis-vrf-common

authentication

authentication { { md5 { { key-chain <word-chain> } | { key-string [ encrypted ] <word-string> } } } | { text <word-text> } } | no authentication

Syntax Description

no

Negate a command or set its defaults

authentication

Configure authentication

md5

MD5 authentication

key-chain

MD5 Key-chain authentication

word-chain

MD5 authentication key-chain

key-string

MD5 keyed authentication

encrypted

(Optional) Specifies an encrypted key will follow

word-string

MD5 authentication key

text

Plain text authentication

word-text

Plain text

Command Mode

  • /exec/configure/if-eth-any/glbp

authentication

[no] authentication [ message-digest | null ]

Syntax Description

no

(Optional) Negate a command or set its defaults

authentication

Authentication on the vlink

message-digest

(Optional) Use message-digest authentication

null

(Optional) Use null(disable) authentication

Command Mode

  • /exec/configure/router-ospf/router-ospf-vlink /exec/configure/router-ospf/vrf/router-ospf-vlink

authentication

[no] authentication [ message-digest | null ]

Syntax Description

no

(Optional) Negate a command or set its defaults

authentication

Authentication on the slink

message-digest

(Optional) Use message-digest authentication

null

(Optional) Use null(disable) authentication

Command Mode

  • /exec/configure/router-ospf/vrf/router-ospf-slink

authentication

authentication { [ text ] <secret> | md5 { key-chain <chain-name> | key-string [ 0 | 7 ] <key-name> [ compatibility ] [ timeout <sec> ] } } | no authentication

Syntax Description

no

Negate a command or set its defaults

authentication

Authentication

text

(Optional) Plain text authentication

secret

Plain text authentication string

md5

Use MD5 authentication

key-chain

Set key chain

chain-name

Name of key-chain

key-string

Set key string

0

(Optional) Specifies an UNENCRYPTED key string will follow

7

(Optional) Specifies a HIDDEN key string will follow

key-name

Key string (64 chars max)

compatibility

(Optional) Operate in compatibility mode for MD5 type-7 authentication

timeout

(Optional) Set timeout

sec

(Optional) (0-32767)Timeout until only accepting new key (seconds)

Command Mode

  • /exec/configure/if-eth-any/hsrp_ipv4 /exec/configure/if-eth-any/hsrp_ipv6

authentication

[no] authentication { { key-chain <chain> } | { mode md5 } }

Syntax Description

no

(Optional) Negate a command or set its defaults

authentication

Configures EIGRP authentication subcommands

key-chain

key-chain

chain

name of key-chain

mode

mode

md5

Keyed message digest

Command Mode

  • /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

authentication

authentication { ipsec spi <spi_id> { md5 <akey> | sha1 <akey> } } | no authentication ipsec spi <spi_id>

Syntax Description

no

Negate a command or set its defaults

authentication

Enable Authentication

ipsec

IPSec

spi

Security Parameter Index

spi_id

SPI Value

md5

Use the MD5 algorithim

akey

Authentication Key

sha1

Use the SHA1 algorithim

akey

Authentication Key

Command Mode

  • /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf

authentication

authentication { disable | ipsec spi <spi_id> { md5 <akey> | sha1 <akey> } } | no authentication { disable | ipsec spi <spi_id> }

Syntax Description

no

Negate a command or set its defaults

authentication

Enable Authentication

disable

Disable Authentication

ipsec

IPSec

spi

Security Parameter Index

spi_id

SPI Value

md5

Use the MD5 algorithim

akey

Authentication Key

sha1

Use the SHA1 algorithim

akey

Authentication Key

Command Mode

  • /exec/configure/router-ospf3/router-ospf3-vlink /exec/configure/router-ospf3/vrf/router-ospf3-vlink

authentication bind

[no] authentication { bind-first [ append-with-basedn <s1> ] | compare [ password-attribute <s0> ] }

Syntax Description

no

(Optional) Negate a command or set its defaults

authentication

Set the authentication method

bind-first

Set the authentication method to bind-first

append-with-basedn

(Optional) Change the default value (cn=$userid)

s1

(Optional) append with dn value

compare

Change the default attribute

password-attribute

(Optional) Change the default password attribute (userPassword)

s0

(Optional) password attribute

Command Mode

  • /exec/configure/ldap

authentication challenge

[no] authentication [ neighbor <nbr> ] challenge

Syntax Description

authentication

Configure RSVP neighbor cryptographic authentication

neighbor

(Optional) Configure RSVP neighbor

nbr

(Optional) RSVP Neighbor address

challenge

Perform challenge/response handshake with new RSVP neighbors

Command Mode

  • /exec/configure/ip-rsvp

authentication key-chain

{ authentication key-chain <keychain> } | { no authentication key-chain [ <keychain> ] }

Syntax Description

no

Negate a command or set its defaults

authentication

Authentication on the vlink

key-chain

Authentication password key-chain

keychain

Key-chain name

Command Mode

  • /exec/configure/router-ospf/router-ospf-vlink /exec/configure/router-ospf/vrf/router-ospf-vlink

authentication key-chain

{ authentication key-chain <keychain> } | { no authentication key-chain [ <keychain> ] }

Syntax Description

no

Negate a command or set its defaults

authentication

Authentication on the slink

key-chain

Authentication password key-chain

keychain

Key-chain name

Command Mode

  • /exec/configure/router-ospf/vrf/router-ospf-slink

authentication key-chain

{ authentication key-chain <auth-keychain> | no authentication key-chain [ <auth-keychain> ] }

Syntax Description

no

Negate a command or set its defaults

authentication

Set authentication keychain string

key-chain

Set authentication keychain string

auth-keychain

authentication keychain

Command Mode

  • /exec/configure/otv-isis/otv-isis-vrf-common

authentication key-chain

{ authentication key-chain <auth-keychain> <level> | no authentication key-chain [ <auth-keychain> ] <level> }

Syntax Description

no

Negate a command or set its defaults

authentication

Set authentication keychain string

key-chain

Set authentication keychain string

auth-keychain

authentication keychain

level

IS-IS level

Command Mode

  • /exec/configure/router-isis/router-isis-vrf-common

authentication key-chain

authentication [ neighbor <nbr> ] key-chain <key-chain-name> | no authentication [ neighbor <nbr> ] key-chain

Syntax Description

authentication

Configure RSVP neighbor cryptographic authentication

neighbor

(Optional) Configure RSVP neighbor

nbr

(Optional) RSVP Neighbor address

key-chain

Authentication password key-chain

key-chain-name

Key-chain name

Command Mode

  • /exec/configure/ip-rsvp

authentication lifetime

[no] authentication [ neighbor <nbr> ] lifetime <time>

Syntax Description

authentication

Configure RSVP neighbor cryptographic authentication

neighbor

(Optional) Configure RSVP neighbor

nbr

(Optional) RSVP Neighbor address

lifetime

Maximum lifetime of neighbor authentication state

time

Lifetime value(in seconds)

Command Mode

  • /exec/configure/ip-rsvp

authentication text

{ authentication text <authentication_pwd> | no authentication [ text <authentication_pwd> ] }

Syntax Description

no

Negate a command or set its defaults

authentication

Select authentication method

text

Set the authentication password (8 char max)

authentication_pwd

Command Mode

  • /exec/configure/if-eth-any/vrrp

authentication type md5

[no] authentication [ neighbor <nbr> ] type { md5 | sha-1 }

Syntax Description

authentication

Configure RSVP neighbor cryptographic authentication

neighbor

(Optional) Configure RSVP neighbor

nbr

(Optional) RSVP Neighbor address

type

Type of authentication algorithm

md5

RSA Message Digest 5 hash algorithm (default)

sha-1

NIST Secure Hash Algorithm 1

Command Mode

  • /exec/configure/ip-rsvp

authentication window-size

[no] authentication [ neighbor <nbr> ] window-size <value>

Syntax Description

authentication

Configure RSVP neighbor cryptographic authentication

neighbor

(Optional) Configure RSVP neighbor

nbr

(Optional) RSVP Neighbor address

window-size

Receive window size for authenticated messages

value

Maximum number of messages allowed in receive window

Command Mode

  • /exec/configure/ip-rsvp

auto-bw

[no] auto-bw | auto-bw [ { [ collect-bw | frequency <sec> ] + } | { [ frequency <sec> | min-bw <min-kbps> | max-bw <max-kbps> ] + } ]

Syntax Description

no

Negate a command or set its defaults

auto-bw

Specify automatic bandwidth configuration

collect-bw

(Optional) Just collect bandwidth info

frequency

(Optional) frequency to change LSP bandwidth

sec

(Optional) seconds between applying auto-bw

max-bw

(Optional) Set the maximum bandwidth for auto-bw

max-kbps

(Optional) Maximum bandwidth to apply (kbps)

min-bw

(Optional) Set the minimum bandwidth for auto-bw

min-kbps

(Optional) Minimum bandwidth to apply (kbps)

Command Mode

  • /exec/configure/te/lsp-attr

auto-bw

[no] auto-bw | auto-bw [ { [ collect-bw | frequency <sec> ] + } | { [ frequency <sec> | min-bw <min-kbps> | max-bw <max-kbps> ] + } ]

Syntax Description

no

Negate a command or set its defaults

auto-bw

Specify mpls tunnel should automatically change bw

collect-bw

(Optional) Just collect Bandwidth info on this tunnel

frequency

(Optional) Frequency to change tunnel BW

sec

(Optional) seconds between applying auto-bw

max-bw

(Optional) Set the Maximum Bandwidth for auto-bw on this tunnel

max-kbps

(Optional) Maximum kb/s that tunnel can be auto set to

min-bw

(Optional) Set the Minimum Bandwidth for auto-bw on this tunnel

min-kbps

(Optional) Min kb/s that tunnel can be auto set to

Command Mode

  • /exec/configure/if-te

auto-bw timers frequency

[no] auto-bw timers { frequency } | auto-bw timers { frequency <sec> }

Syntax Description

no

Negate a command or set its defaults

auto-bw

auto-bw parameters

timers

Enable auto-bw timers

frequency

Interval between auto-bw data collection

sec

Seconds between auto-bw data collection

Command Mode

  • /exec/configure/te

auto-cost reference-bandwidth

auto-cost reference-bandwidth { <ref-bw-mbps> [ Mbps ] | <ref-bw-gbps> Gbps } | no auto-cost reference-bandwidth [ <ref-bw-mbps> [ Mbps ] | <ref-bw-gbps> Gbps ]

Syntax Description

no

Negate a command or set its defaults

auto-cost

Calculate OSPF cost according to bandwidth

reference-bandwidth

Reference bandwidth used to assign OSPF cost

Mbps

(Optional) Specify rate in Mbps

Gbps

Specify rate in Gbps

ref-bw-mbps

Rate in Mbps (bandwidth) (Default)

ref-bw-gbps

Rate in Gbps (bandwidth)

Command Mode

  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

auto-cost reference-bandwidth

auto-cost reference-bandwidth { <ref-bw-mbps> [ Mbps ] | <ref-bw-gbps> Gbps } | no auto-cost reference-bandwidth [ <ref-bw-mbps> [ Mbps ] | <ref-bw-gbps> Gbps ]

Syntax Description

no

Negate a command or set its defaults

auto-cost

Calculate OSPFv3 cost according to bandwidth

reference-bandwidth

Reference bandwidth used to assign OSPFv3 cost

Mbps

(Optional) Specify rate in Mbps

Gbps

Specify rate in Gbps

ref-bw-mbps

Rate in Mbps (bandwidth) (Default)

ref-bw-gbps

Rate in Gbps (bandwidth)

Command Mode

  • /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf

auto-recovery

auto-recovery [ reload-delay <time-out> ] | no auto-recovery [ reload-delay <time-out> ]

Syntax Description

no

Negate a command or set its defaults

auto-recovery

vPC settings to enable auto recovery if peer is presumed non-operational

reload-delay

(Optional) Duration to wait before assuming peer dead and restoring vpcs

time-out

(Optional) Time-out for restoring vPC links (in seconds)

Command Mode

  • /exec/configure/vpc-domain

auto-remap-replication-servers

[no] auto-remap-replication-servers

Syntax Description

no

(Optional) Negate a command or set its defaults

auto-remap-replication-servers

Automatically re-map replication servers on every replication server add

Command Mode

  • /exec/configure/if-nve

autonomous-system

{ { autonomous-system <local-as> } | { no autonomous-system [ <local-as> ] } }

Syntax Description

no

Negate a command or set its defaults

autonomous-system

Specify AS number for Address Family

local-as

Local AS number

Command Mode

  • /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

autoroute announce

[no] autoroute announce

Syntax Description

no

(Optional) Negate a command or set its defaults

autoroute

parameters for IGP routing over tunnel

announce

announce tunnel to IGP

Command Mode

  • /exec/configure/if-te

autoroute metric

[no] autoroute metric | autoroute metric { <value> | relative <rel-value> }

Syntax Description

no

Negate a command or set its defaults

autoroute

parameters for IGP routing over tunnel

metric

Specify mpls tunnel metric

value

Set tunnel metric for autoroutes

relative

Adjust tunnel metric for autoroutes relative to IGP

rel-value

Relative metric value

Command Mode

  • /exec/configure/if-te

autostate

[no] autostate

Syntax Description

no

(Optional) Negate a command or set its defaults

autostate

Enable or disable autostate for interface-vlan

Command Mode

  • /exec/configure/if-vlan

autovlan enable

[no] autovlan enable

Syntax Description

no

(Optional) Negate a command or set its defaults

autovlan

Automatic creation/deletion of VLANs

enable

Enable auto creation/deletion of VLANs

Command Mode

  • /exec/configure/vmt-conn

awk

| awk <expr>

Syntax Description

|

Pipe command output to filter

awk

Mini AWK

expr

Edition command (script)

Command Mode

  • /output