New and Changed Information
Your software release might not support all the features in this document. For the latest caveats and feature information, see the Bug Search Tool at https://tools.cisco.com/bugsearch/ and the release notes for your software release.
|
Feature |
Description |
Changed in Release |
|---|---|---|
|
VDC Resource Limits |
Added support for M3 Series modules. The range for maximum value changed for the limit-resource m6route-mem commands. |
7.3(0)D1(1) |
|
Support for F3 Series modules. |
Added support for F3 Series modules. |
6.2(6) |
|
Cisco Nexus 7710 switch and Cisco Nexus 7718 switch |
Added support for the Cisco Nexus 7710 switch and the Cisco Nexus 7718 switch on the Supervisor 2e module. |
6.2(2) |
|
Supervisor 1 module |
Added support for Admin VDC on Supervisor 1 module. |
6.2(2) |
|
F2e Series module |
Added the ability to enable the F2e Series module (a new configurable VDC module type, independent from and separate to the F2 VDC module type) on the chassis. |
6.2(2) |
|
Switchwide VDC mode |
Added the ability to enable specific line cards in the chassis and prevent others from powering on. |
6.1(3) |
|
Support for F2e Series module |
Added support for F2e Series as part of F2 Series modules. |
6.1(2) |
|
Admin VDC |
Added support for admin VDC. |
6.1(1) |
|
Supervisor modules, Number of VDCs and storage VDCs. |
Added support for the new supervisor modules and the supported number of VDCs. Added support for storage VDCs. |
6.1(1) |
|
CPU Shares |
Added support for CPU shares on a VDC. |
6.1(1) |
|
VDC resource limits |
Added support for M2 Series modules. |
6.1(1) |
|
VDC resource limits |
Added support for F2 Series modules. |
6.0(1) |
|
FCoE |
Added support for storage VDCs and the FCoE feature. |
5.2(1) |
|
MAC addresses |
The default VDC has a MAC address, and subsequent nondefault VDCs that are created are assigned MAC addresses. |
5.2(1) |
|
VDC resource limits |
Added support for M Series modules. |
5.2(1) |
|
N7K-F132XP-15 module |
Added support for the N7K-F132XP-15 module. |
5.1(1) |
|
VDC resource limits |
Added the ability to configure ERSPAN monitor session resource limits. |
5.1(1) |
|
VDC resource limits |
The range for the minimum and maximum values changed for the limit-resource m4route-mem , limit-resource m6route-mem , limit-resource u4route-mem , limit-resource u6route-mem , and limit-resource vrf commands. |
5.0(2) |
|
Restarting VDCs |
The vdc restart command was replaced by the reload vdc command. |
4.2(4) |
|
Suspending and resuming VDCs |
You can suspend and resume nondefault VDCs. |
4.2(1) |
|
Restarting VDCs |
You can restart active nondefault VDCs and nondefault VDCs in the failed state. |
4.2(1) |
|
Reloading VDCs |
You can reload nondefault VDCs. |
4.2(1) |
|
VDC prompt format |
You can change the format of the CLI prompt for nondefault VDCs. |
4.2(1) |
|
VDC boot order |
You can configure the boot order for nondefault VDCs. |
4.2(1) |
|
VDCs and tunnel interfaces |
You can put tunnel interfaces into nondefault VDCs and VRFs. |
4.2(1) |
|
IPv4 and IPv6 unicast route memory resources |
Changed the default value for the maximum limits. |
4.1(2) |
|
Multicast route memory resources |
Added IPv4 and IPv6 multicast route memory resources. |
4.1(2) |
|
Port channel resource |
Changed the default value for the maximum limit. |
4.1(2) |
|
IPv4 unicast route memory resource |
Changed the default maximum value from 256 to 320. |
4.0(2) |
|
IPv6 unicast route memory resource |
Changed the default maximum value from 256 to 192. |
4.0(2) |
Feedback