H Commands

ha-policy single

ha-policy { single-sup <hap-change> | dual-sup <sw-change> } +

Syntax Description

ha-policy

Change HA policy for this VDC

hap-change

Change HA policy for this VDC

single-sup

Change HA policy for this VDC for single-sup situations

dual-sup

Change HA policy for this VDC for dual-sup situations

sw-change

Set hap policy

Command Mode

  • /exec/configure/vdc

ha-stateful

[no] ha-stateful

Syntax Description

no

(Optional) Negate a command or set its defaults

ha-stateful

Enable stateful OSPF HA

Command Mode

  • /exec/configure/router-ospf

hardware access-list lou resource threshold

[no] hardware access-list lou resource threshold <threshold>

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Hardware Internal Information

access-list

Access Control List

lou

LOU

resource

hardware resource

threshold

port expansion threshold

threshold

value of threshold

Command Mode

  • /exec/configure

hardware access-list module

[no] hardware access-list { resource-pooling | resource pooling } module <module-number>

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Show hardware information

access-list

Access Control List

resource-pooling

Enable ACL programming across TCAM banks

resource

hardware resource

pooling

Enable ACL programming across TCAM banks

module

module number

module-number

specify module number

Command Mode

  • /exec/configure

hardware ecmp hash-offset

[no] hardware ecmp hash-offset <value> [ concatenation ]

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Change hardware usage settings

ecmp

ECMP configuration

hash-offset

Configure hash offset

value

Hash offset 0-15 non-concatenate mode, 0-63 concatenate mode

concatenation

(Optional) Configure hash concatenation

Command Mode

  • /exec/configure

hardware ecmp hash-polynomial

hardware ecmp hash-polynomial <poly-type> | no hardware ecmp hash-polynomial

Syntax Description

no

Negate a command or set its defaults

hardware

Change hardware usage settings

ecmp

ECMP configuration

hash-polynomial

Configure hash polynomial

poly-type

Polynomial type

Command Mode

  • /exec/configure

hardware ejector enable

[no] hardware ejector enable

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Hardware Internal Information

ejector

Card ejector functionality

enable

enabled means when both ejectors are open, card is powered down

Command Mode

  • /exec/configure

hardware fan-zone raise-speed

[no] hardware fan-zone <fan_zone_id> raise-speed <speed-to-raise>

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Hardware Internal Information

fan-zone

Fan Zone supported in the switch

fan_zone_id

please enter fan zone id whose speed needs to be increased

raise-speed

Speed to be added for current fan zone speed

speed-to-raise

please enter additional fan speed

Command Mode

  • /exec/configure

hardware forwarding funcstats clear

hardware forwarding funcstats clear

Syntax Description

hardware

Change hardware usage settings

forwarding

Change forwarding related settings

funcstats

Enable/disable funcstats

clear

Clear funcstats information

Command Mode

  • /exec

hardware forwarding funcstats disable

hardware forwarding funcstats disable

Syntax Description

hardware

Change hardware usage settings

forwarding

Change forwarding related settings

funcstats

Enable/disable funcstats

disable

Disable funcstats recording and output

Command Mode

  • /exec

hardware forwarding funcstats enable

hardware forwarding funcstats enable

Syntax Description

hardware

Change hardware usage settings

forwarding

Change forwarding related settings

funcstats

Enable/disable funcstats

enable

Enable funcstats recording and output

Command Mode

  • /exec

hardware forwarding l3 resource route non-deterministic

[no] hardware forwarding l3 resource route non-deterministic

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

hardware information

forwarding

forwarding information

l3

Layer-3

resource

hardware resources

route

TCAM capacity to hold prefixes

non-deterministic

extend upto 1M

Command Mode

  • /exec/configure

hardware forwarding unicast trace

[no] hardware forwarding unicast trace

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Hardware Internal Information

forwarding

Hardware forwarding

unicast

Hardware Unicast forwarding

trace

Debug traces

Command Mode

  • /exec/configure

hardware ip glean throttle

[no] hardware ip glean throttle

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Hardware information

ip

IP

glean

Glean

throttle

Throttle

Command Mode

  • /exec/configure

hardware ip glean throttle maximum

{ hardware ip glean throttle maximum <count> } | { no hardware ip glean throttle maximum }

Syntax Description

no

Negate a command or set its defaults

hardware

Hardware information

ip

IP

glean

Glean

throttle

Throttle

maximum

Maximum number of entries

count

Count

Command Mode

  • /exec/configure

hardware ip glean throttle timeout

{ hardware ip glean throttle timeout <timeout-in-sec> } | { no hardware ip glean throttle timeout }

Syntax Description

no

Negate a command or set its defaults

hardware

Hardware information

ip

IP

glean

Glean

throttle

Throttle

timeout

Timeout

timeout-in-sec

Timeout value in seconds (should be multiple of 30, else will be rounded off to nearest boundary)

Command Mode

  • /exec/configure

hardware module boot-order reverse

[no] hardware module boot-order reverse

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Hardware Internal Information

module

applies on all the modules

boot-order

Configure order of module power-up

reverse

reverse order of module power-up

Command Mode

  • /exec/configure

hardware profile buffer monitor unicast

hardware profile buffer monitor { unicast | multicast } [ internal ] [ sampling <sampling> ] [ threshold <threshold> ] [ interface <intf-num> | sclass <sclass> ] | no hardware profile buffer monitor

Syntax Description

no

Negate a command or set its defaults

hardware

Configure hardware profile buffer monitor settings

profile

profile buffer monitor settings

buffer

Buffer

monitor

buffer monitor

unicast

unicast

multicast

multicast

internal

(Optional) enable buffer monitoring internal mode

sampling

(Optional) sampling interval in nano-seconds

sampling

(Optional) sampling interval in nano-seconds

threshold

(Optional) histogram threshold in Kbytes with 384 Kbytes increment

threshold

(Optional) histogram threshold in Kbytes with 384 Kbytes increment

interface

(Optional) enable buffer monitoring on an interface

intf-num

(Optional) enable buffer monitoring on an interface

sclass

(Optional) enable buffer monitoring on a system class of services

sclass

(Optional) enable buffer monitoring on a system class of services

Command Mode

  • /exec/configure

hardware profile buffer qosgroup threshold

[no] hardware profile buffer qosgroup <groupid> threshold <percentage>

Syntax Description

no

(Optional) Negate the command

hardware

N3500

profile

Profile

buffer

Buffer

qosgroup

Qos-group

groupid

Group-id

threshold

Threshold

percentage

Percentage of maximum usage

Command Mode

  • /exec/configure

hardware profile buffer span-threshold

[no] hardware profile buffer span-threshold <percentage>

Syntax Description

no

(Optional) Negate the command

hardware

N3500

profile

Profile

buffer

Buffer

span-threshold

Span Threshold

percentage

Percentage of maximum usage

Command Mode

  • /exec/configure

hardware profile forwarding-mode

[no] hardware profile forwarding-mode { warp [ lpm-entry <lpm_warp> host-entry <host> l2-entry <l2> mcast-entry <mcst_warp> ] | openflow-hybrid | openflow-only | normal [ lpm-entry <ipv4> mcast-entry <mcst> ] }

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Change hardware usage settings

profile

profile settings

forwarding-mode

Forwarding mode setting

warp

Warp forwarding mode setting

openflow-hybrid

Openflow hybrid forwarding mode setting

openflow-only

Openflow only forwarding mode setting

normal

Normal forwarding mode setting

lpm-entry

(Optional) 4K aligned total IPv4 entries

ipv4

(Optional) 4K aligned total IPv4 entries

mcast-entry

(Optional) 4K aligned total Mcast entries

mcst

(Optional) 4K aligned total Mcast entries

lpm_warp

(Optional) 4K aligned total IPv4 entries

mcst_warp

(Optional) 4K aligned total Mcast entries

host-entry

(Optional) 4K aligned total Host entries

host

(Optional) 4K aligned total Host entries

l2-entry

(Optional) 4K aligned total L2 entries

l2

(Optional) 4K aligned total L2 entries

Command Mode

  • /exec/configure

hardware profile front portmode

hardware profile front portmode <port-mode> | no hardware profile front portmode

Syntax Description

no

Negate a command or set its defaults

hardware

Change hardware usage settings

profile

profile settings

front

port 1 QSFP/SFP+ settings

portmode

QSFP or SFP+

port-mode

Configure QSFP/sfp+ port mode

Command Mode

  • /exec/configure

hardware profile latency monitor

hardware profile latency monitor [ threshold-avg <threshold-avg> ] [ threshold-max <threshold-max> ] [ sampling <sampling> ] | no hardware profile latency monitor

Syntax Description

no

Negate a command or set its defaults

hardware

Configure hardware profile latency monitor settings

profile

profile latency monitor settings

latency

latency

monitor

latency monitor

threshold-avg

(Optional) average latency threshold in nano-seconds

threshold-avg

(Optional) average latency threshold in nano-seconds

threshold-max

(Optional) maximum latency threshold in nano-seconds

threshold-max

(Optional) maximum latency threshold in nano-seconds

sampling

(Optional) sampling interval in seconds

sampling

(Optional) sampling interval in seconds

Command Mode

  • /exec/configure

hardware profile multicast rpf-check-optimization

{ hardware profile multicast rpf-check-optimization } | { no hardware profile multicast rpf-check-optimization }

Syntax Description

no

Negate the command

hardware

Change hardware usage settings

profile

profile settings

multicast

Multicast settings

rpf-check-optimization

RPF Check optimization on Monticello ASIC

Command Mode

  • /exec/configure

hardware profile multicast service-reflect port

{ hardware profile multicast service-reflect port <port-num> } | { no hardware profile multicast service-reflect }

Syntax Description

no

Negate a command or set its defaults

hardware

Change hardware usage settings

profile

profile settings

multicast

Multicast settings

service-reflect

service-reflect settings

port

loopback port

port-num

loopback port-num

Command Mode

  • /exec/configure

hardware profile multicast slow-receiver port

hardware profile multicast slow-receiver port <port> | no hardware profile multicast slow-receiver port <port>

Syntax Description

no

Negate the command

hardware

Change hardware usage settings

profile

Profile

multicast

Multicast settings

slow-receiver

Multicast slow receiver

port

Port

port

Port number

Command Mode

  • /exec/configure

hardware profile multicast syslog-threshold

[no] hardware profile multicast syslog-threshold <percentage>

Syntax Description

no

(Optional) Negate the command

hardware

Change hardware usage settings

profile

profile settings

multicast

Multicast settings

syslog-threshold

MROUTE table syslog threshold

percentage

Percentage (Default is 90)

Command Mode

  • /exec/configure

hardware profile portmode

{ hardware profile portmode <port-mode> [ 2-tuple ] } | no hardware profile portmode

Syntax Description

no

Negate a command or set its defaults

hardware

Change hardware usage settings

profile

profile settings

portmode

QSFP port mode setting

port-mode

Configure QSFP port mode

Command Mode

  • /exec/configure

hardware profile tcam ipv6-sup-tcam match-inner

{ hardware profile tcam ipv6-sup-tcam match-inner } | { no hardware profile tcam ipv6-sup-tcam match-inner }

Syntax Description

no

Negate a command or set its defaults

hardware

Change hardware usage settings

profile

Profile settings

tcam

Configure tcam parameters

ipv6-sup-tcam

IPv6 SUP TCAM parameters

match-inner

match inner payload for tunnel packets

Command Mode

  • /exec/configure

hardware profile tcam region

[no] hardware profile tcam region { <tcam_compat_type> <tcam_compat_size> | ifacl <tcam_compat_size> [ double-wide ] | nat <tcam_compat_size> }

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Hardware Internal Information

profile

profile

tcam

Configure tcam parameters

region

Configure tcam region

ifacl

IPV4 PACL size

nat

NAT size

tcam_compat_type

tcam_compat_size

Enter tcam size

Command Mode

  • /exec/configure

hardware profile tcam syslog-threshold

{ hardware profile tcam syslog-threshold <percentage> } | { no hardware profile tcam syslog-threshold }

Syntax Description

no

Negate a command or set its defaults

hardware

Change hardware usage settings

profile

Profile settings

tcam

Configure tcam parameters

syslog-threshold

TCAMs syslog threshold

percentage

Percentage

Command Mode

  • /exec/configure

hardware profile ucast6 lpm-65-to-127-max-limit

{ hardware profile ucast6 lpm-65-to-127-max-limit <unicast-ent> } | { no hardware profile ucast6 lpm-65-to-127-max-limit }

Syntax Description

no

Negate the command

hardware

Change hardware usage settings

profile

profile settings

ucast6

unicast ipv6 settings

lpm-65-to-127-max-limit

maximum limit for unicast ipv6 lpm-65-to-127 entries, default is 256

unicast-ent

Unicast ipv6 lpm-65-to-127 Table Entries

Command Mode

  • /exec/configure

hardware profile ucast6 max-limit

{ hardware profile ucast6 max-limit <unicast-ent> } | { no hardware profile ucast6 max-limit }

Syntax Description

no

Negate the command

hardware

Change hardware usage settings

profile

profile settings

ucast6

unicast ipv6 settings

max-limit

maximum limit for unicast ipv6 entries

unicast-ent

Unicast ipv6 Table Entries

Command Mode

  • /exec/configure

hardware profile unicast syslog-threshold

{ hardware profile unicast syslog-threshold <percentage> } | { no hardware profile unicast syslog-threshold }

Syntax Description

no

Negate the command

hardware

Change hardware usage settings

profile

profile settings

unicast

Unicast settings

syslog-threshold

Unicast Route table syslog threshold

percentage

Percentage

Command Mode

  • /exec/configure

hardware qos pfc mc-drop

[no] hardware qos pfc mc-drop

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Hardware Internal Information

qos

Configure qos related configuration

pfc

Priority-flow-control specific configuration

mc-drop

Multicast packets are droped in lossless queue

Command Mode

  • /exec/configure

hardware sample-redirect module redirect-interface

hardware sample-redirect module <num> redirect-interface <interface>

Syntax Description

hardware

Change hardware usage settings

sample-redirect

Redirect netflow sampled data

module

Line card module

num

slot number

redirect-interface

Interface for redirecting the traffic

interface

Interface Name

Command Mode

  • /exec

head

| head [ -n <lines> ]

Syntax Description

|

Pipe command output to filter

head

Display first lines

-n

(Optional) modify number of lines (default 10)

lines

(Optional) number of lines to print

Command Mode

  • /output

hello-interval

{ { hello-interval <interval> } | { no hello-interval [ <interval> ] } }

Syntax Description

no

Negate a command or set its defaults

hello-interval

Hello interval

interval

(seconds)

Command Mode

  • /exec/configure/router-ospf/vrf/router-ospf-slink

hello-interval

{ { hello-interval <interval> } | { no hello-interval [ <interval> ] } }

Syntax Description

no

Negate a command or set its defaults

hello-interval

Hello interval

interval

(seconds)

Command Mode

  • /exec/configure/router-ospf/router-ospf-vlink /exec/configure/router-ospf/vrf/router-ospf-vlink

hello-interval

{ { hello-interval <interval> } | { no hello-interval [ <interval> ] } }

Syntax Description

no

Negate a command or set its defaults

hello-interval

Hello interval

interval

(seconds)

Command Mode

  • /exec/configure/router-ospf3/router-ospf3-vlink /exec/configure/router-ospf3/vrf/router-ospf3-vlink

hex

hex <expr>

Syntax Description

hex

calculator with results in decimal format

expr

the expression to compute (integer arithmetics)

Command Mode

  • /exec

history

{ no | default } history { { buckets-kept } | { distributions-of-statistics-kept } | { enhanced [ interval [ <interval-seconds> [ buckets [ <num-buckets> ] ] ] ] } | { filter } | { hours-of-statistics-kept } | { lives-kept } | { statistics-distribution-interval } }

Syntax Description

no

interval

(Optional) buckets

default

Set a command to its defaults

history

History and Distribution Data

buckets-kept

Maximum number of history buckets to collect

distributions-of-statistics-kept

Maximum number of statistics distribution buckets to capture

enhanced

Enable enhanced history collection

interval-seconds

(Optional) Interval in seconds

buckets

(Optional) Number of buckets to collect data

num-buckets

(Optional) Number of buckets

filter

Add operation to History when...

hours-of-statistics-kept

Maximum number of statistics hour groups to capture

lives-kept

Maximum number of history lives to collect

statistics-distribution-interval

Statistics distribution interval size

Command Mode

  • /exec/configure/ip-sla/udp /exec/configure/ip-sla/tcp /exec/configure/ip-sla/icmpEcho

history

history { { buckets-kept <num-buckets-kept> } | { distributions-of-statistics-kept <num-dist-stats> } | { enhanced [ interval [ <interval-seconds> [ buckets [ <num-buckets> ] ] ] ] } | { filter { all | failures | none | overThreshold } } | { hours-of-statistics-kept <num-hours-of-stats> } | { lives-kept <life-size-value> } | { statistics-distribution-interval <dist-interval> } }

Syntax Description

interval

(Optional) buckets

interval-seconds

(Optional) <num-buckets>

life-size-value

<dist-interval>

history

History and Distribution Data

buckets-kept

Maximum number of history buckets to collect

num-buckets-kept

Bucket size value (default 15)

distributions-of-statistics-kept

Maximum number of statistics distribution buckets to capture

num-dist-stats

Distribution bucket size value (default 1)

enhanced

Enable enhanced history collection

buckets

(Optional) Number of buckets to collect data

num-buckets

(Optional) Number of buckets

filter

Add operation to History when...

all

Collect every operation in History

failures

Collect operations that fail in History

none

Shutoff History collection

overThreshold

Collect operations that are over threshold in History

hours-of-statistics-kept

Maximum number of statistics hour groups to capture

num-hours-of-stats

Hour groups size value (default 2)

lives-kept

Maximum number of history lives to collect

statistics-distribution-interval

Statistics distribution interval size

dist-interval

Distribution interval value in msec (default 20ms), Value in usec if precision microsecond is enabled

Command Mode

  • /exec/configure/ip-sla/udp /exec/configure/ip-sla/tcp /exec/configure/ip-sla/icmpEcho

history

{ no | default } history { { buckets-kept } | { distributions-of-statistics-kept } | { filter } | { hours-of-statistics-kept } | { lives-kept } | { statistics-distribution-interval } }

Syntax Description

no

default

Set a command to its defaults

history

History and Distribution Data

buckets-kept

Maximum number of history buckets to collect

distributions-of-statistics-kept

Maximum number of statistics distribution buckets to capture

filter

Add operation to History when...

hours-of-statistics-kept

Maximum number of statistics hour groups to capture

lives-kept

Maximum number of history lives to collect

statistics-distribution-interval

Statistics distribution interval size

Command Mode

  • /exec/configure/ip-sla/dns /exec/configure/ip-sla/fabricPathEcho /exec/configure/ip-sla/http

history

history { { buckets-kept <num-buckets-kept> } | { distributions-of-statistics-kept <num-dist-stats> } | { filter { all | failures | none | overThreshold } } | { hours-of-statistics-kept <num-hours-of-stats> } | { lives-kept <life-size-value> } | { statistics-distribution-interval <dist-interval> } }

Syntax Description

dist-interval

<num-buckets-kept>

num-hours-of-stats

<life-size-value>

distributions-of-statistics-kept

hours-of-statistics-kept

statistics-distribution-interval

history

History and Distribution Data

buckets-kept

Maximum number of history buckets to collect

num-buckets-kept

Bucket size value (default 15)

num-dist-stats

Distribution bucket size value (default 1)

filter

Add operation to History when...

all

Collect every operation in History

failures

Collect operations that fail in History

none

Shutoff History collection

overThreshold

Collect operations that are over threshold in History

hours-of-statistics-kept

Maximum number of statistics hour groups to capture

lives-kept

Maximum number of history lives to collect

life-size-value

Life size value (default 0)

Command Mode

  • /exec/configure/ip-sla/dns /exec/configure/ip-sla/fabricPathEcho /exec/configure/ip-sla/http

history

{ no | default } history { { distributions-of-statistics-kept } | { enhanced [ interval [ <interval-seconds> [ buckets [ <num-buckets> ] ] ] ] } | { hours-of-statistics-kept } | { statistics-distribution-interval } }

Syntax Description

no

interval

(Optional) buckets

distributions-of-statistics-kept

hours-of-statistics-kept

statistics-distribution-interval

default

Set a command to its defaults

history

History and Distribution Data

enhanced

Enable enhanced history collection

interval-seconds

(Optional) Interval in seconds

buckets

(Optional) Number of buckets to collect data

num-buckets

(Optional) Number of buckets

hours-of-statistics-kept

Maximum number of statistics hour groups to capture

Command Mode

  • /exec/configure/ip-sla/jitter

history

history { { distributions-of-statistics-kept <num-dist-stats> } | { enhanced [ interval [ <interval-seconds> [ buckets [ <num-buckets> ] ] ] ] } | { hours-of-statistics-kept <num-hours-of-stats> } | { statistics-distribution-interval <dist-interval> } }

Syntax Description

interval

(Optional) buckets

num-buckets

(Optional) <num-hours-of-stats>

enhanced

hours-of-statistics-kept

history

History and Distribution Data

distributions-of-statistics-kept

Maximum number of statistics distribution buckets to capture

num-dist-stats

Distribution bucket size value (default 1)

interval-seconds

(Optional) Interval in seconds

buckets

(Optional) Number of buckets to collect data

hours-of-statistics-kept

Maximum number of statistics hour groups to capture

num-hours-of-stats

Hour groups size value (default 2)

statistics-distribution-interval

Statistics distribution interval size

dist-interval

Distribution interval value in msec (default 20ms), Value in usec if precision microsecond is enabled

Command Mode

  • /exec/configure/ip-sla/jitter

history buffer

[no] history buffer [ { size [ <onep-historysize> [ purge <historypurge> ] ] } | { purge <historypurge> [ size <onep-historysize> ] } | { session [ <appname-str> ] } ]

Syntax Description

no

(Optional) Negate a command or set its defaults

history

One Platform history trails

buffer

In memory buffering of API history trails

session

(Optional) Session history filter

appname-str

(Optional) Full or partial session name

size

(Optional) History buffer size in bytes

onep-historysize

(Optional) Bytes (default: 32768)

purge

(Optional) Purge the oldest or newest session history

historypurge

(Optional) Purge session history

Command Mode

  • /exec/configure/onep

history syslog

[no] history syslog

Syntax Description

no

(Optional) Negate a command or set its defaults

history

One Platform history trails

syslog

Enable the API history trails to syslog

Command Mode

  • /exec/configure/onep

hold adjacency

hold adjacency <all>

Syntax Description

hold

Hold

adjacency

Display adjacency table

all

Hold all adjcencies

Command Mode

  • /exec

hold ip route

hold ip { route | rnh } [ vrf { <vrf-name> | <vrf-known-name> | <vrf-all> } ] <all>

Syntax Description

hold

Hold

ip

IPv4

route

Hold routing information

rnh

Hold only RNH information

vrf

(Optional) VRF

vrf-name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

vrf-all

(Optional) Display information for all VRFs

all

Hold all routes

Command Mode

  • /exec

hold ipv6 route

hold ipv6 route [ vrf { <vrf-name> | <vrf-known-name> | <vrf-all> } ] <all>

Syntax Description

hold

Hold

ipv6

IPv6

route

Hold routing information

vrf

(Optional) VRF

vrf-name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

vrf-all

(Optional) Display information for all VRFs

all

Hold all routes

Command Mode

  • /exec

hold timeout

hold timeout <timeout_val>

Syntax Description

hold

Hold timer

timeout

timer timeout

timeout_val

timeout duration in seconds

Command Mode

  • /exec/configure/vpc-domain

holdtime

holdtime { infinite | <secs> } | no holdtime

Syntax Description

no

Negate a command or set its defaults

holdtime

LDP session holdtime

infinite

Ignore LDP session holdtime

secs

Holdtime in seconds

Command Mode

  • /exec/configure/ldp

hop-limit maximum

[no] hop-limit maximum <limit>

Syntax Description

no

(Optional) Negate a command or set its defaults

limit

Maximum hop count value allowed

Command Mode

  • /exec/configure/config-ra-guard

hop-limit minimum

[no] hop-limit minimum <limit>

Syntax Description

no

(Optional) Negate a command or set its defaults

limit

Minimum hop count value allowed

Command Mode

  • /exec/configure/config-ra-guard

hop

{ hop <val> } | { no hop }

Syntax Description

no

Negate a command or set its defaults

hop

Configure ngoam hop count

val

Configure ngoam service hop count value

Command Mode

  • /exec/configure/configngoamprofile

host-reachability protocol

[no] host-reachability protocol { bgp | openflow | openflow-ir }

Syntax Description

no

(Optional) Negate a command or set its defaults

host-reachability

Configure host reachability advertisement

protocol

Control protocol to use

bgp

Border Gateway Protocol

openflow

OpenFlow

openflow-ir

OpenFlow-IR

Command Mode

  • /exec/configure/if-nve

host

[no] { host <hostaddr> | <prefix> | <addr> <mask> }

Syntax Description

no

(Optional) Negate a command or set its defaults

host

Host address of the object-group member

hostaddr

A.B.C.D Host address

addr

A.B.C.D Network address of object-group member

mask

A.B.C.D wildcard

prefix

A.B.C.D/nn Network prefix of the object-group member

Command Mode

  • /exec/configure/objgroup

hostname

{ hostname | switchname } <name> | no { hostname | switchname }

Syntax Description

no

Negate a command or set its defaults

hostname

Configure system's host name

switchname

Configure system's host name

name

Enter switchname

Command Mode

  • /exec/configure

hostname dynamic

[no] hostname dynamic

Syntax Description

no

(Optional) Negate a command or set its defaults

hostname

Set dynamic hostname for IS-IS

dynamic

Dynamic hostname

Command Mode

  • /exec/configure/router-isis/router-isis-vrf-common

hostname dynamic

[no] hostname dynamic

Syntax Description

no

(Optional) Negate a command or set its defaults

hostname

Set dynamic hostname for IS-IS

dynamic

Dynamic hostname

Command Mode

  • /exec/configure/otv-isis/otv-isis-vrf-common

hsrp

[no] hsrp <group-id> [ ipv4 ]

Syntax Description

no

(Optional) Negate a command or set its defaults

hsrp

HSRP interface configuration commands

group-id

Group number (0-255 for HSRPv1)

ipv4

(Optional) Configure IP Version 4 group

Command Mode

  • /exec/configure/if-eth-any /exec/configure/if-vlan-common /exec/configure/if-port-channel /exec/configure/if-sub /exec/configure/if-ethernet-all

hsrp anycast

[no] hsrp anycast <id> { ipv4 | ipv6 | both }

Syntax Description

no

(Optional) Negate a command or set its defaults

hsrp

HSRP configuration commands

anycast

Anycast related commands

id

Bundle number

ipv4

Associate IP Version 4 for the bundle

ipv6

Associate IP Version 6 for the bundle

both

Associate IP Version 4 and 6 for the bundle

Command Mode

  • /exec/configure

hsrp delay minimum

hsrp delay { minimum <min-delay> | reload <reload-delay> } + | no hsrp delay [ minimum | reload ]

Syntax Description

no

Negate a command or set its defaults

hsrp

HSRP interface configuration commands

delay

HSRP initialisation delay

minimum

Minimum delay

reload

Delay after reload

min-delay

<0-10000> Delay in seconds

reload-delay

<0-10000> Delay in seconds

Command Mode

  • /exec/configure/if-eth-any /exec/configure/if-vlan-common /exec/configure/if-port-channel /exec/configure/if-sub /exec/configure/if-ethernet-all

hsrp force state vlan

hsrp force state vlan { <vlans> | all }

Syntax Description

hsrp

Hot Standby Router Protocol (HSRP) information

force

Move the HSRP state

state

HSRP state

vlan

HSRP state changes for these vlans

all

Include all HSRP configured VLANs

vlans

VLAN IDs of the VLAN for which state change will affect

Command Mode

  • /exec

hsrp ipv6

[no] hsrp <group-id> ipv6

Syntax Description

no

(Optional) Negate a command or set its defaults

hsrp

HSRP interface configuration commands

group-id

Group number

ipv6

Configure IP Version 6 group

Command Mode

  • /exec/configure/if-eth-any /exec/configure/if-vlan-common /exec/configure/if-port-channel /exec/configure/if-sub /exec/configure/if-ethernet-all

hsrp mac-refresh

hsrp mac-refresh [ <time> ] | no hsrp mac-refresh

Syntax Description

no

Negate a command or set its defaults

hsrp

HSRP interface configuration commands

mac-refresh

Interface mac-refresh time

time

(Optional) Timeout value (0-10000) in sec

Command Mode

  • /exec/configure/if-eth-any /exec/configure/if-vlan-common /exec/configure/if-port-channel /exec/configure/if-sub /exec/configure/if-ethernet-all

hsrp timers extended-hold

[no] hsrp timers extended-hold [ <extended-hold> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

hsrp

HSRP interface configuration commands

timers

Global Timers

extended-hold

Extended Hold

extended-hold

(Optional) Time in seconds

Command Mode

  • /exec/configure

hsrp use-bia

[no] hsrp use-bia [ scope interface ]

Syntax Description

no

(Optional) Negate a command or set its defaults

hsrp

HSRP interface configuration commands

use-bia

HSRP uses interface's burned in address

scope

(Optional) Specify the scope of use-bia

interface

(Optional) Use-bia applies to all groups on this interface or sub-interface

Command Mode

  • /exec/configure/if-eth-any /exec/configure/if-vlan-common /exec/configure/if-port-channel /exec/configure/if-sub /exec/configure/if-ethernet-all

hsrp version 1

hsrp version { 1 | 2 } | no hsrp version

Syntax Description

no

Negate a command or set its defaults

hsrp

HSRP interface configuration commands

version

HSRP version

1

Version 1

2

Version 2

Command Mode

  • /exec/configure/if-eth-any /exec/configure/if-vlan-common /exec/configure/if-port-channel /exec/configure/if-sub /exec/configure/if-ethernet-all

http get

[no] http { get } <WORD> { [ cache { disable | enable } ] [ proxy <proxy-info> ] [ source-ip { <source-ip-hostname> | <source-ip-address> } ] [ source-port <src-port> ] [ version <http-version> ] } +

Syntax Description

no

(Optional)

cache

(Optional) enable

proxy

(Optional) <proxy-info>

source-ip

(Optional) <source-ip-hostname>

source-port

(Optional) <src-port>

version

(Optional) <http-version>

http

HTTP Operation

get

HTTP get operation

WORD

URL

enable

(Optional) enable download of cached entries (default)

disable

(Optional) disable download of cached entries (default)

proxy-info

(Optional) proxy information string

source-ip-hostname

(Optional) source IP hostname, broadcast disallowed

source-ip-address

(Optional) source IP address, broadcast disallowed

src-port

(Optional) Port Number (Recommended port range between 1025-65534)

http-version

(Optional) Supported HTTP versions are '1.0' and '1.1'.

Command Mode

  • /exec/configure/ip-sla

human

| human

Syntax Description

|

Pipe command output to filter

human

output in human format

Command Mode

  • /output

human

| human

Syntax Description

|

Pipe command output to filter

human

output in human format

Command Mode

  • /output

hw-module logging onboard

[no] hw-module logging onboard [ { environmental-history | error-stats | interrupt-stats | module <module> [ { environmental-history | error-stats | interrupt-stats | obfl-logs | cpuhog } ] | obfl-logs | cpuhog } ]

Syntax Description

no

(Optional) Negate a command or set its defaults

hw-module

Enable/Disable OBFL information

logging

Enable/Disable OBFL information

onboard

Enable/Disable OBFL information

environmental-history

(Optional) Enable/Disable OBFL environmental history

error-stats

(Optional) Enable/Disable OBFL error statistics

interrupt-stats

(Optional) Enable/Disable OBFL interrupt statistics

cpuhog

(Optional) Enable/Disable OBFL cpu hog events

module

(Optional) Enable/Disable OBFL information for Module

module

(Optional) Enter module number

obfl-logs

(Optional) Enable/Disable OBFL (boot-uptime/device-version/obfl-history)

Command Mode

  • /exec/configure

hw-module logging onboard

[no] hw-module logging onboard [ { counter-stats | module <module> [ { counter-stats } ] } ]

Syntax Description

no

(Optional) Negate a command or set its defaults

hw-module

Enable/Disable OBFL information

logging

Enable/Disable OBFL information

onboard

Enable/Disable OBFL information

counter-stats

(Optional) Enable/Disable OBFL counter statistics

module

(Optional) Enable/Disable OBFL information for Module

module

(Optional) Enter module number

Command Mode

  • /exec/configure