New and Changed Information in this Release
The following table provides an overview of the significant changes made to this configuration guide. The table does not provide an exhaustive list of all the changes made to this guide or all new features in a particular release.
|
Feature |
Description |
Added or Changed in Release |
Where Documented |
|---|---|---|---|
| Configuring Delay Restore on Orphan Ports | Added support to configure Delay Restore on orphan Ports |
7.0(3)I7(1) |
Configuring Delay Restore on an Orphan Port |
| Configuring the Suspension of Orphan Ports | Added support to configure suspension of orphan Ports |
7.0(3)I7(1) |
Configuring the Suspension of Orphan Ports |
|
Support for speed-auto |
Added support for speed-auto as default port speed. |
7.0(3)I7(1) |
|
|
Configuring FHRP Over VXLAN |
Added support for configuring FHRP |
7.0(3)I7(1) |
|
|
HSRP over VXLAN |
Added Support for HSRP over VXLAN |
7.0(3)I7(1) |
|
|
VXLAN EVPN Multihoming |
Added support for VXLAN EVPN Multihoming on Cisco Nexus 3100 Series Switches |
7.0(3)I7(1) |
|
|
Configuring IP-in-IP tunnel decapsulation on directly connected IP addresses |
Added support for configuring IP-in-IP tunnel decapsulation on any directly connected IP addresses. |
7.0(3)I6(1) |
Guidelines and Limitations for IP Tunnelsand Configuring a Tunnel Interface |
|
VXLAN Support |
Added VXLAN support on Cisco Nexus 3232C and 3264Q switches. |
7.0(3)I6(1) |
|
|
IP unnumbered feature support on port channels. |
Added support for IP unnumbered on port channel interfaces |
7.0(3)I6(1) |
|
|
Layer 3 over vPC |
Added support for Layer 3 over vPC |
7.0(3)I5(1) |
|
|
Support for breakout port modes. |
Introduced breakout port modes for the Cisco Nexus 3132Q-V, 31108PC-V, and 31108TC-V switches. |
7.0(3)I4(2) |
|
|
Support for changing VRF membership for an SVI |
Added support for changing VRF membership for an SVI. |
7.0(3)I4(1) |
|
|
Configuring port profiles |
Added support for port profiles. |
7.0(3)I4(1) |
|
|
Configuring VXLAN BGP EVPN |
Added support for configuring VXLAN BGP EVPN. |
7.0(3)I4(1) |
|
|
IPv6 Across a VXLAN EVPN Fabric |
Added support for IPv6 Across a VXLAN EVPN Fabric |
7.0(3)I4(1) |
|
|
IP unnumbered. |
Added support for IP unnumbered command. |
7.0(3)I3(1) |
|
|
Guidelines for configuring ethernet interfaces. |
Added guidelines for configuring ethernet interfaces. |
7.0(3)I2(1) |
|
|
Duplicate ports on VXLAN multicast encapsulation path. |
VXLAN multicast encapsulation path has duplicate ports after reloading the VPC peers. |
7.0(3)I2(1) |
|
|
Configuring the interface breakout when changing the portmode from QSFP to SFP+. |
Added information on configuring the interface breakout when changing the portmode from QSFP to SFP+ |
7.0(3)I2(1) |
|
|
Updated the running-config output for configuring breakout on QSFP ports. |
Configuring breakout on QSFP ports using speed 10000 adds interface breakout module module number port port range map 10g-4x in the running-config output. |
7.0(3)I2(1) |
|
|
Updated output of the sh vpc brief CLI command. |
The output of the sh vpc brief CLI command displays two additional fields, Delay-restore status and Delay-restore SVI status |
7.0(3)I2(1) |
Guidelines and Limitations for vPCs Viewing a Per-VLAN Consistency Status |
|
Support for LACP min-links. |
The maximum value of LACP min-links supported is 16. |
7.0(3)I2(1) |
|
|
Breakout ports are in administratively enabled state after the breakout of the ports into 4x10G mode or the breakin of the ports into 40G mode. |
The breakout ports are in administratively enabled state after the breakout of the ports into 4x10G mode or the breakin of the ports into 40G mode. On upgrade from the earlier releases, the configuration restored takes care of restoring the appropriate administrative state of the ports. |
7.0(3)I2(1) |
|
|
The VLAN/SVI is not removed from the Layer 3 interface table, after the configuration is removed. |
The VLAN/SVI is not removed from the Layer 3 interface table, after the configuration is removed. The VLAN itself should be removed from the Layer 3 interface table. |
7.0(3)I2(1) |
|
|
Setting the LACP rate on the ports |
You can set the LACP rate only on the ports that are administratively down. |
7.0(3)I2(1) |
|
|
VxLAN multicast group scale |
It is recommended that the summation of the number of the multicast groups and the OIFLs to be used in a scaled environment should not exclude 1024 which is the current range of the multicast VXLAN VP. |
7.0(3)I2(1) |
|
|
The regex and source-interface command options. |
Added information on regex and source-interface command options. |
7.0(3)I2(1) |
Feedback