RST Commands

This chapter provides restore (RST) commands for the Cisco ONS 15454, Cisco ONS 15454 M2, and Cisco ONS 15454 M6.

note.gif

Noteblank.gif All commands supported on the Cisco ONS 15454 platform are also supported on Cisco ONS 15454 M2 and Cisco ONS 15454 M6 platforms.

20.1 RST-<MOD2>

The Restore 10GFC, 10GIGE, 40GIGE, 100GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, 5GIB, 8GFC, CLNT, D1VIDEO, DS1, DV6000, DVBASI, E1, E3, E4, EC1, ESCON, ETRCLO, ETH, FSTE, G1000, GFPOS, GIGE, HDTV, ISC1, ILK, ISCCOMPAT, ISC3PEER2R, ISC3PEER1G, ISC3PEER2G, OC12, OC192, OC3, OC48, OC768, OCH, OMS, OTS, OTU3, OTU4, POS, STS1, STS12C, STS18C, STS192C, STS24C, STS36C, STS3C, STS48C, STS96C, STS6C, STS9C, T1, T3, VC12, VC3, VT1, VT2, 3GVIDEO, SDSDI, HDSDI, AUTO, OTU1, ISC3STP1G, or ISC3STP2G (RST-<MOD2>) command provisions a facility as In-Service (IS).

 
Usage Guidelines

The command supports the modifier 3GVIDEO, SDSDI, HDSDI, AUTO, OTU1, ISC3STP1G, and ISC3STP2G. See Table 28-1 for supported modifiers by platform.

note.gif

Noteblank.gif This command can only be executed when the port is in the Out of Service and Maintenance (OOS,MT) state.

454a96_rst-4.jpg
Category

Ports

454a96_rst-4.jpg
Security

Maintenance

454a96_rst-4.jpg
Input Format

RST-<MOD2>:[<TID>]:<AID>:<CTAG>::::[<PST>[,<SST>]];

454a96_rst-4.jpg
Input Example

RST-OTU1:ROCCIANERA:VFAC-14-3-1:123::::IS,AINS;

454a96_rst-4.jpg
Input Parameters

<AID>

Access identifier from the “ALL” section. The AR-MXP, AR-XP, and AR-XPE cards use the VFAC Access Identifier.

<PST>

Primary state. Defaults to IS. The parameter type is PST, which indicates the current overall service condition of an entity.
  • IS

In service
  • OOS

Out of service

<SST>

Secondary state. Defaults to AINS. The parameter type is SST, which provides additional information pertaining to PST and PSTQ.
  • AINS

Automatic In-Service
  • DSBLD

Disabled
  • LPBK

Loopback
  • MEA

Mismatch of Equipment
  • MT

Maintenance
  • OOG

Out of Group
  • SWDL

Software Download
  • UAS

Unassigned
  • UEQ

Unequipped

20.2 RST-EQPT

(Cisco ONS 15454, ONS 15454 M2, and ONS 15454 M6) The Restore Equipment (RST-EQPT) command provisions equipment into the IS state from the Maintenance (MT) state.

 
Usage Guidelines

This command is only applicable to equipment that is in transition from the Maintenance state to the In-Service state.

454a96_rst-4.jpg
Category

Equipment

454a96_rst-4.jpg
Security

Maintenance

454a96_rst-4.jpg
Input Format

RST-EQPT:[<TID>]:<AID>:<CTAG>[::];

454a96_rst-4.jpg
Input Example

RST-EQPT:CISCO:SLOT-1:1;

454a96_rst-4.jpg
Input Parameters

<AID>

Access identifier from the “EQPT” section.