- Preface
- Cisco ONS Documentation Roadmap for Release 9.6.x
- Chapter 1, ACT Commands
- Chapter 2, ALW Commands
- Chapter 3, Apply Commands
- Chapter 4, CANC Commands and Messages
- Chapter 5, CHG Commands
- Chapter 6, CLR Commands
- Chapter 7, CONN Commands
- Chapter 8, COPY Commands
- Chapter 9, DISC Commands
- Chapter 10, DLT Commands
- Chapter 11, ED Commands
- Chapter 12, ENT Commands
- Chapter 13, EX Commands
- Chapter 14, INH Commands
- Chapter 15, INIT Commands
- Chapter 16, OPR Commands
- Chapter 17, REPT Messages
- Chapter 18, RLS Commands
- Chapter 19, RMV Commands
- Chapter 20, RST Commands
- Chapter 21, RTRV Commands
- Chapter 22, SCHED Commands
- Chapter 23, SET Commands
- Chapter 24, SW Commands
- Chapter 25, TST Commands
- Chapter 26, Access Identifiers
- Chapter 27, Conditions
- Chapter 28, Modifiers
RMV Commands
This chapter provides remove (RMV) commands for the Cisco ONS 15454, Cisco ONS 15454 M2, and Cisco ONS 15454 M6.
Note
All commands supported on the Cisco ONS 15454 platform are also supported on Cisco ONS 15454 M2 and Cisco ONS 15454 M6 platforms.
19.1 RMV-<MOD2>
The Remove 10GFC, 10GIGE, 40GIGE, 100GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, 5GIB, 8GFC, CLNT, D1VIDEO, DS1, DV6000, DVBASI, E1, E3, E4, EC1, ESCON, ETRCLO, ETH, FSTE, G1000, GFPOS, GIGE, HDTV, ISC1, ILK, ISCCOMPAT, ISC3PEER2R, ISC3PEER1G, ISC3PEER2G, OC12, OC192, OC3, OC48, OC768, OCH, OMS, OTS, OTU3, OTU4, POS, STS1, STS12C, STS18C, STS192C, STS24C, STS36C, STS3C, STS48C, STS96C, STS6C, STS9C, T1, T3, VC12, VC3, VT1, VT2, 3GVIDEO, SDSDI, HDSDI, AUTO, OTU1, ISC3STP1G, or ISC3STP2G (RMV-<MOD2>) command removes a facility from service.
Usage Guidelines
The command supports the modifier 3GVIDEO, SDSDI, HDSDI, AUTO, OTU1, ISC3STP1G, and ISC3STP2G.
See Table 28-1 for other supported modifiers by platform.
Category
Security
Input Format
Input Example
Input Parameters
Access identifier from the “ALL” section. The AR-MXP, AR-XP, and AR-XPE cards use the VFAC Access Identifier. |
19.2 RMV-EQPT
(Cisco ONS 15454, ONS 15454 M2, and ONS 15454 M6) The Remove Equipment (RMV-EQPT) command removes equipment from the In Service (IS) state and places it into the Maintenance (MT) state.
Usage Guidelines
This command is only applicable to equipment that is in transition from the IS state to the MT state.
Note This command can be executed only if the equipment is in IS-NR, OOS-AU,MEA or OOS-AU,UEQ state.
Category
Security
Input Format
Input Example
Input Parameters
Access identifier from the “EQPT” section. |
Feedback