- Preface
- Cisco ONS Documentation Roadmap for Release 9.6.x
- Chapter 1, ACT Commands
- Chapter 2, ALW Commands
- Chapter 3, Apply Commands
- Chapter 4, CANC Commands and Messages
- Chapter 5, CHG Commands
- Chapter 6, CLR Commands
- Chapter 7, CONN Commands
- Chapter 8, COPY Commands
- Chapter 9, DISC Commands
- Chapter 10, DLT Commands
- Chapter 11, ED Commands
- Chapter 12, ENT Commands
- Chapter 13, EX Commands
- Chapter 14, INH Commands
- Chapter 15, INIT Commands
- Chapter 16, OPR Commands
- Chapter 17, REPT Messages
- Chapter 18, RLS Commands
- Chapter 19, RMV Commands
- Chapter 20, RST Commands
- Chapter 21, RTRV Commands
- Chapter 22, SCHED Commands
- Chapter 23, SET Commands
- Chapter 24, SW Commands
- Chapter 25, TST Commands
- Chapter 26, Access Identifiers
- Chapter 27, Conditions
- Chapter 28, Modifiers
CHG Commands
This chapter provides change (CHG) commands for the Cisco ONS 15454, Cisco ONS 15454 M2, and Cisco ONS 15454 M6.
Note
All commands supported on the Cisco ONS 15454 platform are also supported on Cisco ONS 15454 M2 and Cisco ONS 15454 M6 platforms.
5.1 CHG-ACCMD-<MOD_TACC>
(Cisco ONS 15454, ONS 15454 M2, and ONS 15454 M6) The Change Test Access Mode for the DS1, DS3I, E1, E3, STS1, STS12C, STS192C, STS24C, STS3C, STS48C, STS96C, STS6C, STS9C, T1, T3, VT1, or VT2 (CHG-ACCMD-<MOD_TACC>) command changes the test access (TACC) mode for the circuit being tested. This can be a change from monitoring the data to inserting data into the synchronous transport signal (STS). For more information about TACC, refer to the Cisco ONS SDH and Cisco ONS 15600 SONET TL1 Reference Guide. See Table 28-1 for supported modifiers by platform.
Usage Guidelines
This command can only be applied to an existing test access point (TAP) connection.
For this command to be applicable, first create the TAP using the ED-<MOD_PATH> command. Intrusive test access modes are traffic-affecting. If a facility/path is connected to a TAP in an intrusive test access mode, it is forced to go into the Out of Service, Maintenance (OOS-MT) state. The forced transition could be traffic-affecting. The present state of the facility/path is stored by the network element (NE) and is restored when the TAP connection is terminated. Test access connections are dropped automatically if the TL1 session is terminated or is timed out.
Note ● If there is no TAP connection, a DENY error message is returned.
- If a requested condition already exists, a SRCN error message is returned.
- If a requested access configuration is invalid, a SRAC error message is returned.
- If a requested TAP does not exist, a RTEN error message is returned.
Category
Security
Input Format
Input Example
Input Parameters
5.2 CHG-EQPT
(Cisco ONS 15454) The Change Equipment (CHG-EQPT) command performs an in-service upgrade from low density (LD) electrical cards (DS1 [DS1-14, DS1N-14], DS3 [DS3-12, DS3N-12, DS3NE-12], EC1, and DS3XM-6) to high density (HD) electrical cards (DS1/E1-56, DS3/EC1-48, and DS3XM-12).
Usage Guidelines
- For Software Release 6.0 and later, only limited upgrades are supported, such as upgrading one LD DS3-12 card to one HD DS3/EC1-48 card.
- Optical (OC-N) card upgrades and downgrades are supported with the limitations of the MRC-12 and MRC-2.5G-4 cards.
- Compatible equipment types for card upgrade:
– DS-3/DS3-N/DS3-E/DS3N-E to DS3/EC1-48
– DS1-14 and DS1N-14 cards that are provisioned in Slot 1, 2, 3, 15, 16, or 17 should be upgraded to DS1/E1-56.
– DS1-14 and DSN-14 cards that are provisioned in Slot 4, 5, 6, 12, 13, or 14 will fail when upgrading to DS1/E1-56.
– DS3-12, DS3N-12, DS3E-12, and DS3N-12E cards that are provisioned in Slot 1, 2, 3, 15, 16, or 17 can be upgraded to DS3/EC1-48.
– DS3-12, DS3N-12, DS3E-12, and DS3N-12E cards that are provisioned in Slot 4, 5, 6, 12, 13, or 14 will fail when upgrading to DS3/EC1-48.
– Two upgradable cards provisioned in a 1:1 protection group cannot be upgraded.
Category
Security
Input Format
CHG-EQPT:[<TID>]:<AID>:<CTAG>::<EQPTTYPE>:[PPMTYPE=PPMTYPE>],
[PPMNUM=<PPMNUM>],[PORTNUM=<PORTNUM>],[PORTRATE=<PORTRATE>];
Input Example
CHG-EQPT::SLOT-14:1::MRC-2.5G-4:PPMTYPE=PPM-1,PPMNUM=1,PORTNUM=1,
PORTRATE=OC48;
Input Parameters
|
|
|
|---|---|
The source access identifier from the “EQPT” section. |
|
The equipment type to be upgraded. The parameter type is EQUIPMENT_TYPE. |
|
Thermal Multiplex/Demultiplex Passive Unit, spaced at 50 GHz on even grid |
|
Thermal Multiplex/Demultiplex Passive Unit, spaced at 50 GHz on odd grid |
|
(ONS 15454) Optical add/drop multiplexed (OADM) 1 band filter |
|
(ONS 15454) Optical add/drop multiplexed (OADM) 1 channel filter |
|
(ONS 15454) Optical add/drop multiplexed (OADM) 2 channels filter |
|
(ONS 15454) Optical add/drop multiplexed (OADM) 4 bands filter |
|
(ONS 15454) Optical add/drop multiplexed (OADM) 4 channels filter |
|
(ONS 15454) 16 x OC3/OC12/OC48/GIGE and OC192/Trunk ADM 10 Gbps card |
|
The equipment type for FMEC STM1E12 card with 1:3 protection |
|
The passive unit Patch Panel device used to connect up to four 40-SMR2-C cards |
|
(ONS 15454) Monviso 10G (4 * 2.5G) muxponder card with enhanced FEC |
|
(ONS 15454) Cengalo 10G (4 * 2.5G) muxponder with enhanced FEC card |
|
(ONS 15454) Multirate 10Gbps datamux with enhanced dispersion |
|
(ONS 15454) Optical service channel (OSC) with combiner/separator module (SCM) |
|
A 4x10G transponder that is capable to operate with multiple bit rates - 10G FC, 10GE, and OC192/STM64 |
|
(ONS 15454) Skane 10G multirate transponder card with enhanced FEC |
|
Identifies the pluggable port module type. This parameter can take only one value. |
|
Identifies the pluggable port module number. This parameter is an Integer. |
|
Identifies the port number, which is used on the entity port with PPM. This para meter is an integer. |
|
Identifies the port rate, which is used to specify the port rate of the multi-rate card. |
|
Feedback