CLR Commands

This chapter provides clear (CLR) commands for the Cisco ONS 15454, Cisco ONS 15454 M2, and Cisco ONS 15454 M6.

note.gif

Noteblank.gif All commands supported on the Cisco ONS 15454 platform are also supported on Cisco ONS 15454 M2 and Cisco ONS 15454 M6 platforms.

6.1 CLR-CCDB-CFM

(Cisco ONS 15454) The Clear Continuity Check Message Data Base Connectivity Fault Management (CLR-CCDB-CFM) command clears the continuity check message data base on a given slot.

 
Usage Guidelines

  • This command is applicable only to GE_XP and 10GE_XP cards.
  • The card should be in Layer2 over DMDM mode.

454a96_clr-4.jpg
Category

Equipment

454a96_clr-4.jpg
Security

Provisioning

454a96_clr-4.jpg
Input Format

CLR-CCDB-CFM:[<TID>]:<AID>:<CTAG>;

454a96_clr-4.jpg
Input Example

CLR-CCDB-CFM::SLOT-4:a;

6.2 CLR-COND-SECU

(Cisco ONS 15454, ONS 15454 M2, and ONS 15454 M6) The Clear Security Condition (CLR-COND-SECU) command clears the specified standing condition.

 
Usage Guidelines

In Software Release 6.0 and later, only the INTRUSION-PSWD parameter value is supported.

454a96_clr-4.jpg
Category

Security

454a96_clr-4.jpg
Security

Superuser

454a96_clr-4.jpg
Input Formats

CLR-COND-SECU:[<TID>]::<CTAG>[::<SECUALMTYPE>];

454a96_clr-4.jpg
Input Examples

CLR-COND-SECU:CISCO::123::INTRUSION-PSWD:

454a96_clr-4.jpg
Input Parameters

<SECUALMTYPE>

Secure alarm type. Defaults to INTRUSION-PSWD. The parameter type is security alarm type (SECUALMTYPE).
  • INTRUSION-PSWD

Condition raised after an invalid password is used during login. Condition is raised only if the password is used a specified number of times.

6.3 CLR-MACTABLE

(Cisco ONS 15454, ONS 15454 M2, and ONS 15454 M6) The CLR-MACTABLE command clears the MAC table that has all the learned MAC addresses.

 
Usage Guidelines

The card should be in Layer2 over DMDM mode to clear the MAC address.

454a96_clr-4.jpg
Category

System

454a96_clr-4.jpg
Security

Retrieve

454a96_clr-4.jpg
Input Format

CLR-MACTABLE:[<TID>]:<AID>:<CTAG>;

454a96_clr-4.jpg
Input Example

CLR-MACTABLE::SLOT-2:1;

6.4 CLR-MEPSTATS-CFM

(Cisco ONS 15454) The Clear Maintenance End Point Statistics Connectivity Fault Management (CLR-MEPSTATS-CFM) command clears the maintenance end point statistics.

 
Usage Guidelines

  • This command is applicable only to GE_XP and 10GE_XP cards.
  • The card should be in Layer2 over DMDM mode.

454a96_clr-4.jpg
Category

Equipment

454a96_clr-4.jpg
Security

Provisioning

454a96_clr-4.jpg
Input Format

CLR-MEPSTATS-CFM:[<TID>]:<AID>:<CTAG>;

454a96_clr-4.jpg
Input Example

CLR-MEPSTATS-CFM::SLOT-15:1;