This sample configuration allows a VPN Client to access a server on another network through an IPsec tunnel, after the user authentication succeeds.
A PC at 188.8.131.52 brings up the web browser to access content on the server at 10.13.1.98. Since the VPN Client on the PC is configured to go through tunnel end-point 184.108.40.206 to get to the 10.13.1.x network, the IPsec tunnel is built and the PC gets the IP address out of the pool called "ourpool" (since you are doing mode-configuration). The 3640 router requests authentication. After the user enters a username and password (stored on the TACACS+ server at 172.18.124.97), the access list passed down from the server gets added to access list 117.
Note: The ip auth-proxy command was introduced in Cisco IOS® Software Release 12.0.5.T.
There are no specific requirements for this document.
The information in this document is based on these software and hardware versions:
Cisco IOS Software Release 12.0.7.T
Cisco 3640 router (c3640-jo3s56i-mz.121-2.3.T)
Cisco Secure VPN Client 1.0 (shown as 2.0.7 in the IRE client Help > About menu) or Cisco Secure VPN Client 1.1 (shown as 2.1.12 in the IRE client Help > About menu)
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Refer to the Cisco Technical Tips Conventions for more information on document conventions.
In this section, you are presented with the information to configure the features described in this document.
This document uses this network setup:
This document uses this configuration:
|Cisco 3640 Router Configuration|
Current configuration: ! version 12.1 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname carter ! aaa new-model aaa authentication login default group tacacs+ none aaa authorization exec default group tacacs+ none aaa authorization auth-proxy default group tacacs+ enable secret 5 $1$cSvL$F6VxA7kBFAGHvhBbRlNS20 enable password ww ! ip subnet-zero ! ip inspect name myfw cuseeme timeout 3600 ip inspect name myfw ftp timeout 3600 ip inspect name myfw http timeout 3600 ip inspect name myfw rcmd timeout 3600 ip inspect name myfw realaudio timeout 3600 ip inspect name myfw smtp timeout 3600 ip inspect name myfw sqlnet timeout 3600 ip inspect name myfw streamworks timeout 3600 ip inspect name myfw tftp timeout 30 ip inspect name myfw udp timeout 15 ip inspect name myfw tcp timeout 3600 ip inspect name myfw vdolive ip auth-proxy auth-proxy-banner ip auth-proxy auth-cache-time 10 ip auth-proxy name list_a http ip audit notify log ip audit po max-events 100 cns event-service server ! crypto isakmp policy 10 hash md5 authentication pre-share crypto isakmp key cisco1234 address 0.0.0.0 0.0.0.0 crypto isakmp client configuration address-pool local ourpool ! crypto ipsec transform-set mypolicy esp-des esp-md5-hmac ! crypto dynamic-map dyna 10 set transform-set mypolicy ! crypto map test client configuration address initiate crypto map test client configuration address respond crypto map test 5 ipsec-isakmp dynamic dyna ! interface Loopback0 ip address 220.127.116.11 255.255.255.0 ! interface Ethernet0/0 ip address 10.13.1.48 255.255.255.0 ip nat inside ip inspect myfw in ip route-cache policy no ip mroute-cache ip policy route-map nonat no mop enabled ! interface TokenRing0/0 no ip address shutdown ring-speed 16 ! interface Ethernet2/0 ip address 18.104.22.168 255.255.255.0 ip access-group 117 in ip nat outside ip auth-proxy list_a no ip route-cache no ip mroute-cache no mop enabled crypto map test ! interface TokenRing2/0 no ip address shutdown ring-speed 16 ! ip local pool ourpool 10.2.1.1 10.2.1.254 ip nat pool outsidepool 22.214.171.124 126.96.36.199 netmask 255.255.255.0 ip nat inside source route-map rmap pool outsidepool ip classless ip route 0.0.0.0 0.0.0.0 188.8.131.52 ip route 172.18.124.0 255.255.255.0 10.13.1.1 no ip http server ! access-list 110 deny ip 10.13.1.0 0.0.0.255 10.2.1.0 0.0.0.255 access-list 110 permit ip 10.13.1.0 0.0.0.255 any access-list 117 permit esp any any access-list 117 permit udp any any eq isakmp access-list 120 permit ip 10.13.1.0 0.0.0.255 10.2.1.0 0.0.0.255 dialer-list 1 protocol ip permit dialer-list 1 protocol ipx permit route-map rmap permit 10 match ip address 110 ! route-map nonat permit 10 match ip address 120 set ip next-hop 184.108.40.206 ! route-map nonat permit 20 ! tacacs-server host 172.18.124.97 tacacs-server key cisco ! line con 0 transport input none line aux 0 line vty 0 4 password ww ! end
There is currently no verification procedure available for this configuration.
Refer to Troubleshooting Authentication Proxy for troubleshooting information.
Note: Refer to Important Information on Debug Commands before you use debug commands.
The Cisco Support Community is a forum for you to ask and answer questions, share suggestions, and collaborate with your peers.
Refer to Cisco Technical Tips Conventions for information on conventions used in this document.