Feedback
Table Of Contents
Show Commands for Viewing the Configuration
show 802.11 cleanair air-quality summary
show 802.11 cleanair air-quality worst
show 802.11 cleanair device ap
show 802.11 cleanair device type
show advanced backup-controller
show advanced send-disassoc-on-handoff
show ap join stats summary all
show certificate compatibility
show client ccx client-capability
show client ccx last-response-status
show client ccx last-test-status
show client ccx manufacturer-info
show client ccx operating-parameters
show client location-calibration summary
show media-stream group detail
show media-stream group summary
show network multicast mgid detail
show network multicast mgid summary
show nmsp notify-interval summary
show radius rfc3576 statistics
Show Radio Frequency ID Commands
show rogue ap friendly summary
show rogue ap malicious summary
show rogue ap unclassified summary
show wps ap-authentication summary
Configuring Controller Settings
Configure 802.11 Network Commands
Configure 802.11 Public Safety Commands
config 802.11-a antenna extAntGain
config 802.11h powerconstraint
Configure 802.11 11n Support Commands
config 802.11 11nsupport a-mpdu tx priority
config 802.11 11nsupport antenna
config 802.11 11nsupport mcs tx
Configure 802.11 Antenna Commands
config 802.11 antenna diversity
config 802.11 antenna extAntGain
config 802.11 antenna selection
Configure 802.11 cleanair commands
config 802.11 cac video max-bandwidth
config 802.11 cac video roam-bandwidth
config 802.11 cac video tspec-inactivity-timeout
config 802.11 cac voice max-bandwidth
config 802.11 cac voice roam-bandwidth
config 802.11 cac voice tspec-inactivity-timeout
config 802.11 cac voice load-based
config 802.11 cac voice max-calls
config 802.11 cac voice sip bandwidth
config 802.11 cac voice sip codec
config 802.11 cac voice stream-size
config 802.11 l2roam rf-params
Configure Advanced 802.11 Commands
config advanced 802.11 7920VSIEConfig
Configure Advanced 802.11 Channel Commands
config advanced 802.11 channel add
config advanced 802.11 channel cleanair-event
config advanced 802.11 channel cleanair-event
config advanced 802.11 channel dca anchor-time
config advanced 802.11 channel dca chan-width-11n
config advanced 802.11 channel dca interval
config advanced 802.11 channel dca sensitivity
config advanced 802.11 channel foreign
config advanced 802.11 channel load
config advanced 802.11 channel noise
config advanced 802.11 channel outdoor-ap-dca
config advanced 802.11 channel update
Configure Advanced 802.11 Coverage Commands
config advanced 802.11 coverage
config advanced 802.11 coverage exception global
config advanced 802.11 coverage fail-rate
config advanced 802.11 coverage level global
config advanced 802.11 coverage packet-count
config advanced 802.11 coverage rssi-threshold
config advanced 802.11 edca-parameters
config advanced 802.11 factory
config advanced 802.11 group-mode
Configure Advanced 802.11 Logging Commands
config advanced 802.11 logging channel
config advanced 802.11 logging coverage
config advanced 802.11 logging foreign
config advanced 802.11 logging load
config advanced 802.11 logging noise
config advanced 802.11 logging performance
config advanced 802.11 logging txpower
Configure Advanced 802.11 Monitor Commands
config advanced 802.11 monitor channel-list
config advanced 802.11 monitor coverage
config advanced 802.11 monitor load
config advanced 802.11 monitor mode
config advanced 802.11 monitor noise
config advanced 802.11 monitor signal
Configure Advanced 802.11 Profile Commands
config advanced 802.11 profile clients
config advanced 802.11 profile customize
config advanced 802.11 profile foreign
config advanced 802.11 profile noise
config advanced 802.11 profile throughput
config advanced 802.11 profile utilization
config advanced 802.11 receiver
config advanced 802.11 txpower-update
config advanced backup-controller primary
config advanced backup-controller secondary
config advanced client-handoff
Configure Advanced Timers Commands
config advanced timers ap-discovery-timeout
config advanced timers ap-fast-heartbeat
config advanced timers ap-heartbeat-timeout
config advanced timers ap-primary-discovery-timeout
config advanced timers auth-timeout
config advanced timers eap-timeout
config advanced timers eap-identity-request-delay
Configure Access Point Commands
config ap crash-file clear-all
config ap crash-file get-crash-file
config ap crash-file get-radio-core-dump
config ap h-reap radius auth set
config ap logging syslog level
config ap syslog host specific
Configure band-select commands
config band-select cycle-count
config band-select cycle-threshold
config band-select client-rssi
config client ccx clear-reports
config client ccx clear-results
config client ccx default-gw-ping
config client ccx get-client-capability
config client ccx get-manufacturer-info
config client ccx get-operating-parameters
config client ccx get-profiles
config client ccx send-message
config client ccx stats-request
config client ccx test-association
config client ccx test-profile
config client location-calibration
config custom-web ext-webauth-mode
config custom-web ext-webauth-url
config custom-web ext-webserver
config custom-web webauth-type
config guest-lan custom-web ext-webauth-url
config guest-lan custom-web global disable
config guest-lan custom-web login_page
config guest-lan custom-web webauth-type
config guest-lan ingress-interface
config guest-lan mobility anchor
config interface quarantine vlan
config local-auth active-timeout
config local-auth user-credentials
config logging syslog facility
config macfilter mac-delimiter
config macfilter radius-compat
Configure Memory Monitor Commands
config mesh background-scanning
config mesh backhaul dca-channels
config mesh backhaul rate-adapt
config mesh ethernet-bridging vlan-transparent
config mesh secondary-backhaul
Configure Management-User Commands
config mobility group keepalive count
config mobility group keepalive interval
config mobility group multicast-addres
config mobility multicast-mode
config mobility statistics reset
Configure Message Log Level Commands
Configure Media-Stream Commands
config netuser guest-role apply
config netuser guest-role create
config netuser guest-role delete
config netuser guest-role qos data-rate average-data-rate
config netuser guest-role qos data-rate average-realtime-rate
config netuser guest-role qos data-rate burst-data-rate
config netuser guest-role qos data-rate burst-realtime-rate
config netuser maxEapUserLogin
config network allow-old-bridge-aps
config network bridging-shared-secret
config network fast-ssid-change
config network mgmt-via-wireless
config network multicast global
config network multicast igmp snooping
config network multicast igmp timeout
config network multicast mode multicast
config network multicast mode unicast
config network rf-network-name
config network secureweb cipher-option
config nmsp notify-interval measurement
config port multicast appliance
config qos average-realtime-rate
config qos burst-realtime-rate
config qos protocol-type/config qos dot1p-tag
Configure RADIUS Account Commands
config radius acct IPsec authentication
config radius acct IPsec disable
config radius acct IPsec enable
config radius acct IPsec encryption
config radius acct mac-delimiter
config radius acct retransmit-timeout
Configure RADIUS Authentication Server Commands
config radius auth IPsec authentication
config radius auth IPsec disable
config radius auth IPsec encryption
config radius auth mac-delimiter
config radius auth retransmit-timeout
config radius auth server-timeout
config radius aggressive-failover disabled
config radius backward compatibility
config radius callStationIdType
config snmp community accessmode
config snmp trapreceiver create
config snmp trapreceiver delete
Configure Spanning Tree Protocol Commands
config spanningtree port pathcost
config spanningtree port priority
config spanningtree switch bridgepriority
config spanningtree switch forwarddelay
config spanningtree switch hellotime
config spanningtree switch maxage
config spanningtree switch mode
config switchconfig flowcontrol
config switchconfig secret-obfuscation
config trapflags 802.11-Security
config trapflags authentication
Configure Wireless LAN Commands
config wlan channel-scan defer-priority
config wlan channel-scan defer-time
config wlan h-reap learn-ipaddr
config wlan h-reap local-switching
config wlan radius_server overwrite-interface
Configure Wireless LAN Security Commands
config wlan security cond-web-redir
config wlan security IPsec disable
config wlan security IPsec enable
config wlan security IPsec authentication
config wlan security IPsec encryption
config wlan security IPsec config
config wlan security IPsec ike authentication
config wlan security IPsec ike dh-group
config wlan security IPsec ike lifetime
config wlan security IPsec ike phase1
config wlan security IPsec ike contivity
config wlan security splash-page-web-redir
config wlan security static-wep-key authentication
config wlan security static-wep-key disable
config wlan security static-wep-key enable
config wlan security static-wep-key encryption
config wlan security web-passthrough acl
config wlan security web-passthrough disable
config wlan security web-passthrough email-input
config wlan security web-passthrough enable
config wlan security wpa1 disable
config wlan security wpa1 enable
config wlan security wpa1 pre-shared-key
config wlan security wpa2 disable
config wlan security wpa2 enable
config wlan security wpa2 pre-shared-key
config wlan security wpa2 tkip
config wlan security wpa2 wpa-compat
config wps signature frequency
config wps signature mac-frequency
config wps signature quiet-time
capwap ap controller ip address
lwapp ap controller ip address
Clearing Configurations, Logfiles, and Other Actions
clear location statistics rfid
Resetting the System Reboot Time
Uploading and Downloading Files and Configurations
transfer download tftpPktTimeout
transfer download tftpMaxRetries
Installing and Modifying Licenses
debug dot11 mgmt state-machine
CLI Commands
The Cisco Wireless LAN solution command-line interface (CLI) enables operators to connect an ASCII console to the Cisco wireless LAN controller and configure the controller and its associated access points.
This chapter contains the commands available in the Cisco CLI release 7.0. The controllers currently covered are as follows:
•
Cisco 2100, 4400, and 5500 Series Wireless LAN Controllers
•
•
•
This document contains the following sections:
•
•
•
•
•
Show Commands for Viewing the Configuration
To display Cisco wireless LAN controller options and settings, use the show commands.
Show 802.11 Commands
Use the show 802.11 commands to display more detailed 802.11a, 802.11b/g, or other supported 802.11 network settings.
show 802.11
To display basic 802.11a, 802.11b/g, or 802.11h network settings, use the show 802.11 command.
show 802.11{a | b | h}
Syntax Description
a
Specifies the 802.11a network.
b
Specifies the 802.11b/g network.
h
Specifies the 802.11h network.
Defaults
None.
Examples
This example shows to display basic 802.11a network settings:
> show 802.11a802.11a Network.................................. Enabled11nSupport....................................... Enabled802.11a Low Band........................... Enabled802.11a Mid Band........................... Enabled802.11a High Band.......................... Enabled802.11a Operational Rates802.11a 6M Rate.............................. Mandatory802.11a 9M Rate.............................. Supported802.11a 12M Rate............................. Mandatory802.11a 18M Rate............................. Supported802.11a 24M Rate............................. Mandatory802.11a 36M Rate............................. Supported802.11a 48M Rate............................. Supported802.11a 54M Rate............................. Supported802.11n MCS Settings:MCS 0........................................ SupportedMCS 1........................................ SupportedMCS 2........................................ SupportedMCS 3........................................ SupportedMCS 4........................................ SupportedMCS 5........................................ Supported--More-- or (q)uitMCS 6........................................ SupportedMCS 7........................................ SupportedMCS 8........................................ SupportedMCS 9........................................ SupportedMCS 10....................................... SupportedMCS 11....................................... SupportedMCS 12....................................... SupportedMCS 13....................................... SupportedMCS 14....................................... SupportedMCS 15....................................... Supported802.11n Status:A-MPDU Tx:Priority 0............................... EnabledPriority 1............................... DisabledPriority 2............................... DisabledPriority 3............................... DisabledPriority 4............................... DisabledPriority 5............................... DisabledPriority 6............................... DisabledPriority 7............................... DisabledBeacon Interval.................................. 100CF Pollable mandatory............................ DisabledCF Poll Request mandatory........................ Disabled--More-- or (q)uitCFP Period....................................... 4CFP Maximum Duration............................. 60Default Channel.................................. 36Default Tx Power Level........................... 0DTPC Status..................................... EnabledFragmentation Threshold.......................... 2346TI Threshold..................................... -50Legacy Tx Beamforming setting.................... DisabledTraffic Stream Metrics Status.................... EnabledExpedited BW Request Status...................... DisabledWorld Mode....................................... EnabledEDCA profile type................................ default-wmmVoice MAC optimization status.................... DisabledCall Admission Control (CAC) configurationVoice AC:Voice AC - Admission control (ACM)............ DisabledVoice max RF bandwidth........................ 75Voice reserved roaming bandwidth.............. 6Voice load-based CAC mode..................... DisabledVoice tspec inactivity timeout................ DisabledVoice Stream-Size............................. 84000Voice Max-Streams............................. 2Video AC:--More-- or (q)uitVideo AC - Admission control (ACM)............ DisabledVideo max RF bandwidth........................ InfiniteVideo reserved roaming bandwidth.............. 0This example shows how to display basic 802.11h network settings:
> show 802.11h802.11h ......................................... powerconstraint : 0802.11h ......................................... channelswitch : Disable802.11h ......................................... channelswitch mode : 0Related Commands
show ap stats
show ap summary
show client summary
show interface
show network
show network summary
show port
show wlanshow 802.11 cleanair
To display the multicast-direct configuration state, use the show 802.11 cleanair command.
show 802.11{a | b | h} cleanair config
Syntax Description
a
Specifies the 802.11a network.
b
Specifies the 802.11b/g network.
h
Specifies the 802.11h network.
config
Displays the network cleanair configuration.
Defaults
None.
Examples
This example shows how to display the 802.11a cleanair configuration:
> show 802.11a cleanair configClean Air Solution............................... EnabledAir Quality Settings:Air Quality Reporting........................ EnabledAir Quality Reporting Period (min)........... 15Air Quality Alarms........................... EnabledAir Quality Alarm Threshold.................. 35 Interference Device Settings:Interference Device Reporting................ EnabledInterference Device Types:TDD Transmitter.......................... DisabledJammer................................... DisabledContinuous Transmitter................... DisabledDECT-like Phone.......................... DisabledVideo Camera............................. DisabledWiFi Inverted............................ DisabledWiFi Invalid Channel..................... DisabledSuperAG.................................. DisabledRadar.................................... DisabledCanopy................................... DisabledWiMax Mobile............................. DisabledWiMax Fixed.............................. DisabledInterference Device Alarms................... EnabledInterference Device Types Triggering Alarms:TDD Transmitter.......................... DisabledJammer................................... DisabledContinuous Transmitter................... DisabledDECT-like Phone.......................... DisabledVideo Camera............................. DisabledWiFi Inverted............................ DisabledWiFi Invalid Channel..................... DisabledSuperAG.................................. DisabledRadar.................................... DisabledCanopy................................... DisabledWiMax Mobile............................. DisabledWiMax Fixed.............................. Disabled Additional Clean Air Settings:CleanAir Event-driven RRM State.............. EnabledCleanAir Driven RRM Sensitivity.............. MediumCleanAir Persistent Devices state............ DisabledRelated Commands
config 802.11 cleanair alarm
config 802.11 cleanair device
show 802.11 cleanair air-quality summary
show 802.11 cleanair device ap
show 802.11 cleanair device typeshow 802.11 cleanair air-quality summary
To display the air quality summary information for the 802.11 networks, use the
show 802.11 cleanair air-quality summary command.show 802.11{a | b | h} cleanair air-quality summary
Syntax Description
a
Specifies the 802.11a network.
b
Specifies the 802.11b/g network.
h
Specifies the 802.11h network.
summary
Displays a summary of 802.11 radio band air quality information.
Defaults
None.
Examples
This example shows how to display a summary of the air quality information for the 802.11a network:
> show 802.11a cleanair air-quality summaryAQ = Air QualityDFS = Dynamic Frequency SelectionAP Name Channel Avg AQ Min AQ Interferers DFS------------------ ------- ------ ------ ----------- ---CISCO_AP3500 36 95 70 0CISCO_AP3500 40 93 75 0Related Commands
config 802.11 cleanair alarm
config 802.11 cleanair device
show 802.11 cleanair
show 802.11 cleanair device ap
show 802.11 cleanair device typeshow 802.11 cleanair air-quality worst
To display the worst air quality information for the 802.11 networks, use the
show 802.11 cleanair air-quality worst command.show 802.11{a | b | h} cleanair air-quality worst
Syntax Description
a
Specifies the 802.11a network.
b
Specifies the 802.11b/g network.
h
Specifies the 802.11h network.
worst
Displays the worst air quality information for 802.11 networks.
Defaults
None.
Examples
This example shows how to display worst air quality information for the 802.11a network:
> show 802.11a cleanair air-quality worstAQ = Air QualityDFS = Dynamic Frequency SelectionAP Name Channel Avg AQ Min AQ Interferers DFS------------------ ------- ------ ------ ----------- ---CISCO_AP3500 1 83 57 3 5Related Commands
config 802.11 cleanair alarm
config 802.11 cleanair device
show 802.11 cleanair
show 802.11 cleanair device ap
show 802.11 cleanair device typeshow 802.11 cleanair device ap
To display the information of the device access point on the 802.11 radio band, use the show 802.11 cleanair device ap command.
show 802.11{a | b | h} cleanair device ap cisco_ap
Syntax Description
a
Specifies the 802.11a network.
b
Specifies the 802.11b/g network.
h
Specifies the 802.11h network.
cisco_ap
Specified access point name.
Defaults
None.
Examples
This example shows how to display the device access point for the 802.11a network:
> show 802.11a cleanair device ap AP_3500DC = Duty Cycle (%)ISI = Interference Severity Index (1-Low Interference, 100-High Interference)RSSI = Received Signal Strength Index (dBm)DevID = Device IDNo ClusterID DevID Type AP Name ISI RSSI DC Channel--- ------------------ ------ ---------- --------------- ---- ----- ---- -------------1 c2:f7:40:00:00:03 0x8001 DECT phone CISCO_AP3500 1 -43 3 149,153,157,1612 c2:f7:40:00:00:51 0x8002 Radar CISCO_AP3500 1 -81 2 153,157,161,1653 c2:f7:40:00:00:03 0x8005 Canopy CISCO_AP3500 2 -62 2 153,157,161,165Related Commands
config 802.11 cleanair alarm
config 802.11 cleanair device
show 802.11 cleanair
show 802.11 cleanair air-quality summary
show 802.11 cleanair device typeshow 802.11 cleanair device type
To display the information of all the interferers device type detected by a specific access point on the 802.11 radio band, use the show 802.11 cleanair device type command.
show 802.11{a | b | h} cleanair device type device_type
Syntax Description
Defaults
None.
Examples
This example shows how to display the information of all the interferers detected by a specified access point for the 802.11a network:
> show 802.11a cleanair device type CanopyDC = Duty Cycle (%)ISI = Interference Severity Index (1-Low Interference, 100-High Interference)RSSI = Received Signal Strength Index (dBm)DevID = Device IDNo ClusterID DevID Type AP Name ISI RSSI DC Channel--- ------------------ ------ ---------- --------------- ---- ----- ---- -------------1c2:f7:40:00:00:03 0x8005 Canopy CISCO_AP3500 2 -62 2 153,157,161,165show 802.11 media-stream
To display the multicast-direct configuration state, use the show 802.11 media-stream command.
show 802.11{a | b | h} media-stream media-stream name
Syntax Description
a
Specifies the 802.11a network.
b
Specifies the 802.11b/g network.
h
Specifies the 802.11h network.
media_stream_name
Specified media stream name.
Defaults
None.
Examples
This example shows how to display the media-stream configuration:
> show 802.11a media-stream rrcMulticast-direct................................. EnabledBest Effort...................................... DisabledVideo Re-Direct.................................. EnabledMax Allowed Streams.............................. AutoMax Video Bandwidth.............................. 0Max Voice Bandwidth.............................. 75Max Media Bandwidth.............................. 85Min PHY Rate..................................... 6000Related Commands
show 802.11 media-stream
Show Mesh Commands
show media-stream group summary
show aaa auth
To display the configuration settings for the AAA authentication server database, use the show aaa auth command.
show aaa auth
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the configuration settings for the AAA authentication server database:
> show aaa authManagement authentication server order:1............................................ local2............................................ tacacsRelated Commands
config aaa auth
config aaa auth mgmtshow acl
To display the access control lists (ACLs) that are configured on the controller, use the show acl command.
show acl {summary | detailed acl_name}
Syntax Description
summary
Displays a summary of all ACLs configured on the controller.
detailed
Displays detailed information about a specific ACL.
acl_name
ACL name. The name can be up to 32 alphanumeric characters.
Defaults
None.
Examples
This example shows how to display a summary of the access control lists:
> show acl summaryACL Counter Status Enabled-------------------------------------ACL Name Applied------------------------- -----------acl1 Yesacl2 Yesacl3 YesThis example shows how to display the detailed information of the access control lists:
> show acl detailed acl_nameSource Destination Source Port Dest PortI Dir IP Address/Netmask IP Address/Netmask Prot Range Range DSCP Action Counter- --- ------------------ ------------------ ---- --------- --------- ----- ------ -------1 Any 0.0.0.0/0.0.0.0 0.0.0.0/0.0.0.0 Any 0-65535 0-65535 0 Deny 02 In 0.0.0.0/0.0.0.0 200.200.200.0/ 6 80-80 0-65535 Any Permit 0255.255.255.0DenyCounter : 0
Note
Related Commands
clear acl counters
config acl apply
config acl counter
config acl cpu
config acl create
config acl deleteconfig interface acl
config acl rule
show acl cpushow acl cpu
To display the access control lists (ACLs) configured on the central processing unit (CPU), use the show acl cpu command.
show acl cpu
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the access control lists on the CPU:
> show acl cpuCPU Acl Name................................Wireless Traffic............................ DisabledWired Traffic............................... DisabledApplied to NPU.............................. NoRelated Commands
clear acl counters
config acl apply
config acl counter
config acl cpu
config acl create
config acl delete
config acl rule
config interface acl
show aclShow Advanced 802.11 Commands
Use the show advanced 802.11 commands to display more detailed or advanced 802.11a, 802.11b/g, or other supported 802.11 network settings.
show advanced 802.11 channel
To display the automatic channel assignment configuration and statistics, use the show advanced 802.11 channel command.
show advanced 802.11{a | b} channel
Syntax Description
Defaults
None.
Examples
This example shows how to display the automatic channel assignment configuration and statistics:
> show advanced 802.11a channelAutomatic Channel AssignmentChannel Assignment Mode........................ AUTOChannel Update Interval........................ 600 seconds [startup]Anchor time (Hour of the day).................. 0Channel Update Contribution.................... SNI.Channel Assignment Leader...................... 00:1a:6d:dd:1e:40Last Run....................................... 129 seconds agoDCA Sensitivity Level: ...................... STARTUP (5 dB)Channel Energy LevelsMinimum...................................... unknownAverage...................................... unknownMaximum...................................... unknownChannel Dwell TimesMinimum...................................... unknownAverage...................................... unknownMaximum...................................... unknownAuto-RF Allowed Channel List................... 36,40,44,48,52,56,60,64,149,............................................. 153,157,161Auto-RF Unused Channel List.................... 100,104,108,112,116,132,136,............................................. 140,165,190,196DCA Outdoor AP option.......................... EnabledRelated Commands
config advanced 802.11 channel add
config advanced 802.11 channel cleanair-event
config advanced 802.11 channel dca anchor-time
config advanced 802.11 channel dca chan-width-11n
config advanced 802.11 channel dca interval
config advanced 802.11 channel dca sensitivity
config advanced 802.11 channel foreign
config advanced 802.11 channel load
config advanced 802.11 channel noise
config advanced 802.11 channel update
show advanced 802.11 channel
show advanced 802.11 coverage
To display the configuration and statistics for coverage hole detection, use the show advanced 802.11 coverage command.
show advanced 802.11{a | b} coverage
Syntax Description
Defaults
None.
Examples
This example shows how to display the statistics for coverage hole detection:
> show advanced 802.11a coverageCoverage Hole Detection802.11a Coverage Hole Detection Mode........... Enabled802.11a Coverage Voice Packet Count............ 100 packets802.11a Coverage Voice Packet Percentage....... 50%802.11a Coverage Voice RSSI Threshold.......... -80 dBm802.11a Coverage Data Packet Count............. 50 packets802.11a Coverage Data Packet Percentage........ 50%802.11a Coverage Data RSSI Threshold........... -80 dBm802.11a Global coverage exception level........ 25 %802.11a Global client minimum exception lev.... 3 clientsRelated Commands
config advanced 802.11 coverage
config advanced 802.11 coverage exception global
config advanced 802.11 coverage fail-rate
config advanced 802.11 coverage level global
config advanced 802.11 coverage packet-count
config advanced 802.11 coverage rssi-threshold
show advanced 802.11 coverage
show advanced 802.11 group
To display 802.11a or 802.11b Cisco radio RF grouping, use the show advanced 802.11 group command.
show advanced 802.11{a | b} group
Syntax Description
Defaults
None.
Examples
This example shows how to display Cisco radio RF group settings:
> show advanced 802.11a groupRadio RF Grouping802.11a Group Mode................................... AUTO802.11a Group Update Interval........................ 600 seconds802.11a Group Leader................................. xx:xx:xx:xx:xx:xx802.11a Group Member............................... xx:xx:xx:xx:xx:xx802.11a Last Run..................................... 133 seconds agoRelated Commands
config advanced 802.11 group-mode
show advanced 802.11 l2roam
To display 802.11a or 802.11b/g Layer 2 client roaming information, use the show advanced 802.11 l2roam command.
show advanced 802.11{a | b} l2roam {rf-param | statistics mac_address}
Syntax Description
Defaults
None.
Examples
This example shows how to display 802.11b Layer 2 client roaming information, enter this command:
> show advanced 802.11b l2roam rf-paramL2Roam 802.11bg RF Parameters.....................Config Mode.................................. DefaultMinimum RSSI................................. -85Roam Hysteresis.............................. 2Scan Threshold............................... -72Transition time.............................. 5Related Commands
config 802.11 l2roam rf-params
show advanced 802.11 logging
To display 802.11a or 802.11b RF event and performance logging, use the show advanced 802.11 logging command.
show advanced 802.11{a | b} logging
Syntax Description
Defaults
None.
Examples
This example shows how to display 802.11b RF event and performance logging:
> show advanced 802.11b loggingRF Event and Performance LoggingChannel Update Logging......................... OffCoverage Profile Logging....................... OffForeign Profile Logging........................ OffLoad Profile Logging........................... OffNoise Profile Logging.......................... OffPerformance Profile Logging.................... OffTxPower Update Logging......................... OffRelated Commands
config advanced 802.11 logging channel
config advanced 802.11 logging coverage
config advanced 802.11 logging foreign
config advanced 802.11 logging load
config advanced 802.11 logging noise
config advanced 802.11 logging performance
config advanced 802.11 logging txpower
show advanced 802.11 channel
show advanced 802.11 monitor
To display the 802.11a or 802.11b default Cisco radio monitoring, use the show advanced 802.11 monitor command.
show advanced 802.11{a | b} monitor
Syntax Description
Defaults
None.
Examples
This example shows how to display the radio monitoring for the 802.11b network:
> show advanced 802.11b monitorDefault 802.11b AP monitoring802.11b Monitor Mode........................... enable802.11b Monitor Channels....................... Country channels802.11b AP Coverage Interval................... 180 seconds802.11b AP Load Interval....................... 60 seconds802.11b AP Noise Interval...................... 180 seconds802.11b AP Signal Strength Interval............ 60 secondsRelated Commands
config advanced 802.11 monitor load
config advanced 802.11 monitor mode
config advanced 802.11 monitor noise
config advanced 802.11 monitor signal
show advanced 802.11 profile
To display the 802.11a or 802.11b lightweight access point performance profiles, use the show advanced 802.11 profile command.
show advanced 802.11{a | b} profile {global | cisco_ap}
Syntax Description
a
Specifies the 802.11a network.
b
Specifies the 802.11b/g network.
global
Specifies all Cisco lightweight access points.
cisco_ap
Name of a specific Cisco lightweight access point.
Defaults
None.
Examples
This example shows how to display the global configuration and statistics of an 802.11a profile:
> show advanced 802.11a profile globalDefault 802.11a AP performance profiles802.11a Global Interference threshold.............. 10%802.11a Global noise threshold..................... -70 dBm802.11a Global RF utilization threshold............ 80%802.11a Global throughput threshold................ 1000000 bps802.11a Global clients threshold................... 12 clientsThis example shows how to display the configuration and statistics of a specific access point profile:
> show advanced 802.11a profile AP1Cisco AP performance profile not customizedThis response indicates that the performance profile for this lightweight access point is using the global defaults and has not been individually configured.
Related Commands
config advanced 802.11 profile clients
config advanced 802.11 profile customize
config advanced 802.11 profile foreign
config advanced 802.11 profile noiseshow advanced 802.11 receiver
To display the configuration and statistics of the 802.11a or 802.11b receiver, use the show advanced 802.11 receiver command.
show advanced 802.11{a | b} receiver
Syntax Description
Defaults
None.
Examples
This example shows how to display the configuration and statistics of the 802.11a network settings:
> show advanced 802.11a receiver802.11a Receiver SettingsRxStart : Signal Threshold........................... 15RxStart : Signal Lamp Threshold...................... 5RxStart : Preamble Power Threshold................... 2RxReStart : Signal Jump Status......................... EnabledRxReStart : Signal Jump Threshold...................... 10TxStomp : Low RSSI Status.............................. EnabledTxStomp : Low RSSI Threshold........................... 30TxStomp : Wrong BSSID Status........................... EnabledTxStomp : Wrong BSSID Data Only Status................. EnabledRxAbort : Raw Power Drop Status........................ DisabledRxAbort : Raw Power Drop Threshold..................... 10RxAbort : Low RSSI Status.............................. DisabledRxAbort : Low RSSI Threshold........................... 0RxAbort : Wrong BSSID Status........................... DisabledRxAbort : Wrong BSSID Data Only Status................. DisabledRelated Commands
config advanced 802.11 profile clients
show advanced 802.11 summary
To display the 802.11a or 802.11b Cisco lightweight access point name, channel, and transmit level summary, use the show advanced 802.11 summary command.
show advanced 802.11{a | b} summary
Syntax Description
Defaults
None.
Examples
This example shows how to display a summary of the 802.11b access point settings:
> show advanced 802.11b summaryAP Name MAC Address Admin State Operation State Channel TxPower------------ ------------------ ------------ ----------------- ------- --------CJ-1240 00:21:1b:ea:36:60 ENABLED UP 161 1( )CJ-1130 00:1f:ca:cf:b6:60 ENABLED UP 56* 1(*)
Note
Related Commands
config advanced 802.11 7920VSIEConfig
config advanced 802.11 channel add
show advanced 802.11 channelshow advanced 802.11 txpower
To display the 802.11a or 802.11b automatic transmit power assignment, use the show advanced 802.11 txpower command.
show advanced 802.11{a | b} txpower
Syntax Description
Defaults
None.
Examples
This example shows how to display the configuration and statistics of the 802.11b transmit power cost:
> show advanced 802.11b txpowerAutomatic Transmit Power AssignmentTransmit Power Assignment Mode.................. AUTOTransmit Power Update Interval.................. 600 secondsTransmit Power Threshold........................ -65 dBmTransmit Power Neighbor Count................... 3 APsTransmit Power Update Contribution.............. SN.Transmit Power Assignment Leader................ xx:xx:xx:xx:xx:xxLast Run........................................ 384 seconds agoRelated Commands
config advanced 802.11 txpower-update
show advanced backup-controller
To display a list of primary and secondary backup controllers, use the show advanced backup-controller command.
show advanced backup-controller
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the backup controller information:
> show advanced backup-controllerAP primary Backup Controller .................... controller 10.10.10.10AP secondary Backup Controller .................. 0.0.0.0Related Commands
config advanced backup-controller primary
config advanced backup-controller secondaryshow advanced client-handoff
To display the number of automatic client handoffs after retries, use the show advanced client-handoff command.
show advanced client-handoff
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the client auto handoff mode after excessive retries:
> show advanced client-handoffClient auto handoff after retries................ 130Related Commands
config advanced client-handoff
show advanced 802.11 summaryshow advanced dot11-padding
To display the state of over-the-air frame padding on a wireless LAN controller, use the show advanced dot11-padding command.
show advanced dot11-padding
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to view the state of over-the-air frame padding:
> show advanced dot11-paddingdot11-padding.................................... DisabledRelated Commands
config advanced dot11-padding
debug dot11
debug dot11 mgmt interface
debug dot11 mgmt msg
debug dot11 mgmt ssid
debug dot11 mgmt state-machine
debug dot11 mgmt stationshow advanced eap
To display Extensible Authentication Protocol (EAP) settings, use the show advanced eap command.
show advanced eap
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the EAP settings:
> show advanced eapEAP-Identity-Request Timeout (seconds)........... 1EAP-Identity-Request Max Retries................. 20EAP Key-Index for Dynamic WEP.................... 0EAP Max-Login Ignore Identity Response........... enableEAP-Request Timeout (seconds).................... 1EAP-Request Max Retries.......................... 20EAPOL-Key Timeout (milliseconds)................. 1000EAPOL-Key Max Retries............................ 2Related Commands
config advanced eap
config advanced timers eap-identity-request-delay
config advanced timers eap-timeout
show advanced max-1x-sessions
To display the maximum number of simultaneous 802.1X sessions allowed per access point, use the show advanced max-1x-sessions command.
show advanced max-1x-sessions
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the maximum 802.1X sessions per access point:
> show advanced max-1x-sessionsMax 802.1x session per AP at a given time........ 0Related Commands
show advanced probe
To display the number of probes sent to the WLAN controller per access point per client and the probe interval in milliseconds, use the show advanced probe command.
show advanced probe
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the probe settings for the WLAN controller:
> show advanced probeProbe request filtering.......................... Enabled Probes fwd to controller per client per radio.... 12 Probe request rate-limiting interval............. 100 msecRelated Commands
config advanced probe filter
config advanced probe limitshow advanced rate
To display whether control path rate limiting is enabled or disabled, use the show advanced rate command.
show advanced rate
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the switch control path rate limiting mode:
> show advanced rateControl Path Rate Limiting....................... DisabledRelated Commands
config advanced rate
config advanced eapshow advanced send-disassoc-on-handoff
To display whether the WLAN controller disassociates clients after a handoff, use the show advanced send-disassoc-on-handoff command.
show advanced send-disassoc-on-handoff
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the disassociated clients after a handoff:
> show advanced send-disassoc-on-handoffSend Disassociate on Handoff..................... Disabled
show advanced statistics
To display whether or not the Cisco wireless LAN controller port statistics are enabled or disabled, use the show advanced statistics command.
show advanced statistics
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display switch port statistics mode:
> show advanced statisticsSwitch port statistics........................... EnabledRelated Commands
show advanced timers
To display the mobility anchor, authentication response, and rogue access point entry timers, use the show advanced timers command.
show advanced timers
Syntax Description
This command has no arguments or keywords.
Defaults
The defaults are shown in the "Examples" section.
Examples
This example shows how to display the system timers setting:
> show advanced timersAuthentication Response Timeout (seconds)........ 10Rogue Entry Timeout (seconds).................... 1200AP Heart Beat Timeout (seconds).................. 30AP Discovery Timeout (seconds)................... 10AP Local mode Fast Heartbeat (seconds)........... disableAP Hreap mode Fast Heartbeat (seconds)........... disableAP Primary Discovery Timeout (seconds)........... 120Related Commands
config advanced timers ap-discovery-timeout
config advanced timers ap-fast-heartbeat
config advanced timers ap-heartbeat-timeout
config advanced timers ap-primary-discovery-timeout
config advanced timers auth-timeout
config advanced timers eap-identity-request-delay
config advanced timers eap-timeout
Show Access Point Commands
Use the show ap commands to show access point settings.
show ap auto-rf
To display the auto-RF settings for a Cisco lightweight access point, use the show ap auto-rf command.
show ap auto-rf 802.11{a | b} cisco_ap
Syntax Description
a
Specifies the 802.11a network.
b
Specifies the 802.11b/g network.
cisco_ap
Cisco lightweight access point name.
Defaults
None.
Examples
This example shows how to display auto-RF information for an access point:
> show ap auto-rf 802.11a AP1Number Of Slots.................................. 2AP Name.......................................... AP03MAC Address...................................... 00:0b:85:01:18:b7Radio Type..................................... RADIO_TYPE_80211aNoise InformationNoise Profile................................ PASSEDChannel 36................................... -88 dBmChannel 40................................... -86 dBmChannel 44................................... -87 dBmChannel 48................................... -85 dBmChannel 52................................... -84 dBmChannel 56................................... -83 dBmChannel 60................................... -84 dBmChannel 64................................... -85 dBmInterference InformationInterference Profile......................... PASSEDChannel 36................................... -66 dBm @ 1% busyChannel 40................................... -128 dBm @ 0% busyChannel 44................................... -128 dBm @ 0% busyChannel 48................................... -128 dBm @ 0% busyChannel 52................................... -128 dBm @ 0% busyChannel 56................................... -73 dBm @ 1% busyChannel 60................................... -55 dBm @ 1% busyChannel 64................................... -69 dBm @ 1% busyRogue Histogram (20/40_ABOVE/40_BELOW)Channel 36................................... 16/ 0/ 0Channel 40................................... 28/ 0/ 0Channel 44................................... 9/ 0/ 0Channel 48................................... 9/ 0/ 0Channel 52................................... 3/ 0/ 0Channel 56................................... 4/ 0/ 0Channel 60................................... 7/ 1/ 0Channel 64................................... 2/ 0/ 0Load InformationLoad Profile................................. PASSEDReceive Utilization.......................... 0%Transmit Utilization......................... 0%Channel Utilization.......................... 1%Attached Clients............................. 1 clientsCoverage InformationCoverage Profile............................. PASSEDFailed Clients............................... 0 clientsClient Signal StrengthsRSSI -100 dBm................................ 0 clientsRSSI -92 dBm................................ 0 clientsRSSI -84 dBm................................ 0 clientsRSSI -76 dBm................................ 0 clientsRSSI -68 dBm................................ 0 clientsRSSI -60 dBm................................ 0 clientsRSSI -52 dBm................................ 0 clientsClient Signal To Noise RatiosSNR 0 dBm................................. 0 clientsSNR 5 dBm................................. 0 clientsSNR 10 dBm................................. 0 clientsSNR 15 dBm................................. 0 clientsSNR 20 dBm................................. 0 clientsSNR 25 dBm................................. 0 clientsSNR 30 dBm................................. 0 clientsSNR 35 dBm................................. 0 clientsSNR 40 dBm................................. 0 clientsSNR 45 dBm................................. 0 clientsNearby RADsRAD 00:0b:85:01:05:08 slot 0................. -46 dBm on 10.1.30.170RAD 00:0b:85:01:12:65 slot 0................. -24 dBm on 10.1.30.170Channel Assignment InformationCurrent Channel Average Energy............... -86 dBmPrevious Channel Average Energy.............. -75 dBmChannel Change Count......................... 109Last Channel Change Time..................... Wed Sep 29 12:53e:34 2004Recommended Best Channel..................... 44RF Parameter RecommendationsPower Level.................................. 1RTS/CTS Threshold............................ 2347Fragmentation Threshold...................... 2346Antenna Pattern.............................. 0show ap ccx rm
To display an access point's Cisco Client eXtensions (CCX) radio management status information, use the show ap ccx rm command.
show ap ccx rm ap_name status
Syntax Description
ap_name
Specified access point name.
status
Displays the CCX radio management status information for an access point.
Defaults
None.
Examples
This example shows how to display the status of the CCX radio management:
> show ap ccx rm AP1240-21ac statusA RadioChannel Load Request ..................... DisabledNoise Histogram Request .................. DisabledBeacon Request ........................... DisabledFrame Request ............................ DisabledInterval ................................. 60Iteration ................................ 10G RadioChannel Load Request ..................... DisabledNoise Histogram Request .................. DisabledBeacon Request ........................... DisabledFrame Request ............................ DisabledInterval ................................. 60Iteration ................................ 10Related Commands
show ap cdp
To display the Cisco Discovery Protocol (CDP) information for an access point, use the show ap cdp commands.
show ap cdp {all | ap-name cisco_ap | neighbors {all | ap-name cisco_ap | detail cisco_ap}}
Syntax Description
Defaults
None.
Examples
This example shows how to display the CDP status of all access points:
> show ap cdp allAP CDP StateAP Name AP CDP State------------------ ----------SB_RAP1 enableSB_MAP1 enableSB_MAP2 enableSB_MAP3 enableThis example shows how to display the CDP status of a specified access point:
> show ap cdp ap-name SB_RAP1AP CDP StateAP Name AP CDP State------------------ ----------SB_RAP1 enableThis example shows how to display details about all neighbors using CDP:
> show ap cdp neighbors allAP Name AP IP Neighbor Name Neighbor IP Neighbor Port--------- --------------- ------------------ -------------- -------------SB_RAP1 192.168.102.154 sjc14-41a-sw1 192.168.102.2 GigabitEthernet1/0/13SB_RAP1 192.168.102.154 SB_MAP1 192.168.102.137 Virtual-Dot11Radio0SB_MAP1 192.168.102.137 SB_RAP1 192.168.102.154 Virtual-Dot11Radio0SB_MAP1 192.168.102.137 SB_MAP2 192.168.102.138 Virtual-Dot11Radio0SB_MAP2 192.168.102.138 SB_MAP1 192.168.102.137 Virtual-Dot11Radio1SB_MAP2 192.168.102.138 SB_MAP3 192.168.102.139 Virtual-Dot11Radio0SB_MAP3 192.168.102.139 SB_MAP2 192.168.102.138 Virtual-Dot11Radio1This example shows how to display details about a specific neighbor with a specified access point using CDP:
> show ap cdp neighbors ap-name SB_MAP2AP Name AP IP Neighbor Name Neighbor IP Neighbor Port----------- --------------- --------------- -------------- -------------SB_MAP2 192.168.102.138 SB_MAP1 192.168.102.137 Virtual-Dot11Radio1SB_MAP2 192.168.102.138 SB_MAP3 192.168.102.139 Virtual-Dot11Radio0This example shows how to display details about neighbors using CDP:
> show ap cdp neighbors detail SB_MAP2AP Name:SB_MAP2AP IP address:192.168.102.138-------------------------Device ID: SB_MAP1Entry address(es): 192.168.102.137Platform: cisco AIR-LAP1522AG-A-K9 , CapInterface: Virtual-Dot11Radio0, Port ID (outgoing port): Virtual-Dot11Radio1Holdtime : 180 secVersion :Cisco IOS Software, C1520 Software (C1520-K9W8-M), Experimental Version 12.4(20081114:084420) [BLD-v124_18a_ja_throttle.20081114 208] Copyright (c) 1986-2008 byCisco Systems, Inc. Compiled Fri 14-Nov-08 23:08 byadvertisement version: 2-------------------------Device ID: SB_MAP3Entry address(es): 192.168.102.139Platform: cisco AIR-LAP1522AG-A-K9 , Capabilities: Trans-BridgeInterface: Virtual-Dot11Radio1, Port ID (outgoing port): Virtual-Dot11Radio0Holdtime : 180 secVersion :Cisco IOS Software, C1520 Software (C1520-K9W8-M), Experimental Version 12.4(20081114:084420) [BLD-v124_18a_ja_throttle.20081114 208] Copyright (c) 1986-2008 byCisco Systems, Inc. Compiled Fri 14-Nov-08 23:08 byadvertisement version: 2Related Commands
show ap channel
To display the available channels for a specific mesh access point, use the show ap channel command.
show ap channel ap_name
Syntax Description
Defaults
None.
Examples
This example shows how to display the available channels for a particular access point:
> show ap channel AP47802.11b/g Current Channel ...........1Allowed Channel List.....................1,2,3,4,5,6,7,8,9,10,11802.11a Current Channel .................161Allowed Channel List.....................36,40,44,48,52,56,60,64,100,.........................................104,108,112,116,132,136,140,.........................................149,153,157,161Related Commands
config 802.11-a channel ap
config 802.11h channelswitch
config 802.11h setchannelshow ap config
To display the detailed configuration for a lightweight access point, use the show ap config command.
show ap config {802.11{a | b} | general} cisco_ap
Syntax Description
802.11a
Specifies the 802.11a or 802.11b/g network.
802.11b
Specifies the 802.11b/g network.
general
Displays general access point settings.
cisco_ap
Lightweight access point name.
Defaults
None.
Examples
This example shows how to display the detailed configuration for an access point:
> show ap config 802.11a AP02Cisco AP Identifier.............................. 0Cisco AP Name.................................... AP02AP Regulatory Domain............................. UnconfiguredSwitch Port Number .............................. 1MAC Address...................................... 00:0b:85:18:b6:50IP Address Configuration......................... DHCPIP Address....................................... 1.100.49.240IP NetMask....................................... 255.255.255.0Gateway IP Addr.................................. 1.100.49.1Cisco AP Location................................ default-locationCisco AP Group Name.............................. default-groupPrimary Cisco Switch............................. Cisco_32:ab:63Secondary Cisco Switch...........................Tertiary Cisco Switch............................Administrative State ............................ ADMIN_ENABLEDOperation State ................................. REGISTEREDMirroring Mode .................................. DisabledAP Mode ........................................... SnifferPublic Safety ..................................... Global: Disabled, Local: DisabledSniffing .............................................. NoRemote AP Debug ................................. DisabledS/W Version .................................... 3.1.61.0Boot Version ................................... 1.2.59.6Stats Re--More-- or (q)uitporting Period .................................. 180LED State........................................ EnabledILP Pre Standard Switch.......................... DisabledILP Power Injector............................... DisabledNumber Of Slots.................................. 2AP Model......................................... AS-1200AP Serial Number................................. 044110223AAP Certificate Type.............................. Manufacture InstalledAttributes for Slot 0Radio Type................................... RADIO_TYPE_80211aAdministrative State ........................ ADMIN_ENABLEDOperation State ............................. UPCellId ...................................... 0Station ConfigurationConfiguration ............................. AUTOMATICNumber Of WLANs ........................... 1Medium Occupancy Limit .................... 100CFP Period ................................ 4CFP MaxDuration ........................... 60BSSID ..................................... 00:0b:85:18:b6:50Operation Rate Set6000 Kilo Bits........................... MANDATORY9000 Kilo Bits........................... SUPPORTED12000 Kilo Bits.......................... MANDATORY18000 Kilo Bits.......................... SUPPORTED24000 Kilo Bits.......................... MANDATORY36000 Kilo Bits.......................... SUPPORTED48000 Kilo Bits.......................... SUPPORTED54000 Kilo Bits.......................... SUPPORTEDBeacon Period ............................. 100DTIM Period ............................... 1Fragmentation Threshold ................... 2346Multi Domain Capability Implemented ....... TRUEMulti Domain Capability Enabled ........... TRUECountry String ............................ USMulti Domain CapabilityConfiguration ............................. AUTOMATICFirst Chan Num ............................ 36Number Of Channels ........................ 4MAC Operation ParametersConfiguration ............................. AUTOMATICRTS Threshold ............................. 2347Short Retry Limit ......................... 7Long Retry Limit .......................... 4Fragmentation Threshold ................... 2346Maximum Tx MSDU Life Time ................. 512Maximum Rx Life Time ...................... 512Tx PowerNum Of Supported Power Levels ............. 5Tx Power Level 1 .......................... 18 dBmTx Power Level 2 .......................... 15 dBmTx Power Level 3........................... 12 dBmTx Power Level 4 .......................... 9 dBmTx Power Level 5 .......................... 6 dBmTx Power Configuration .................... CUSTOMIZEDCurrent Tx Power Level..................... 5Phy OFDM parametersConfiguration ............................. AUTOMATICCurrent Channel ........................... 36TI Threshold .............................. -50Legacy Tx Beamforming Configuration ....... CUSTOMIZEDLegacy Tx Beamforming ..................... ENABLEDAntenna Type............................... INTERNAL_ANTENNAInternal Antenna Gain (in .5 dBm units).... 11AntennaMode................................ ANTENNA_OMNIPerformance Profile ParametersConfiguration ............................. AUTOMATICInterference threshold..................... 10%Noise threshold............................ -70 dBmRF utilization threshold................... 80%Data-rate threshold........................ 1000000 bpsClient threshold........................... 12 clientsCoverage SNR threshold..................... 16 dBCoverage exception level................... 25%Client minimum exception level............. 3 clientsRogue Containment InformationContainment Count............................ 0This example shows how to display the detailed configuration for another access point:
> show ap config 802.11b AP02Cisco AP Identifier.............................. 0Cisco AP Name.................................... AP02AP Regulatory Domain............................. UnconfiguredSwitch Port Number .............................. 1MAC Address...................................... 00:0b:85:18:b6:50IP Address Configuration......................... DHCPIP Address....................................... 1.100.49.240IP NetMask....................................... 255.255.255.0Gateway IP Addr.................................. 1.100.49.1Cisco AP Location................................ default-locationCisco AP Group Name.............................. default-groupPrimary Cisco Switch............................. Cisco_32:ab:63Secondary Cisco Switch...........................Tertiary Cisco Switch............................Administrative State ............................ ADMIN_ENABLEDOperation State ................................. REGISTEREDMirroring Mode .................................. DisabledAP Mode ......................................... LocalRemote AP Debug ................................. DisabledS/W Version .................................... 3.1.61.0Boot Version ................................... 1.2.59.6Stats Reporting Period .......................... 180LED State........................................ EnabledILP Pre Standard Switch.......................... DisabledILP Power Injector............................... DisabledNumber Of Slots.................................. 2AP Model......................................... AS-1200AP Serial Number................................. 044110223AAP Certificate Type.............................. Manufacture InstalledAttributes for Slot 1Radio Type................................... RADIO_TYPE_80211gAdministrative State ........................ ADMIN_ENABLEDOperation State ............................. UPCellId ...................................... 0Station ConfigurationConfiguration ............................. AUTOMATICNumber Of WLANs ........................... 1Medium Occupancy Limit .................... 100CFP Period ................................ 4CFP MaxDuration ........................... 60BSSID ..................................... 00:0b:85:18:b6:50Operation Rate Set1000 Kilo Bits........................... MANDATORY2000 Kilo Bits........................... MANDATORY5500 Kilo Bits........................... MANDATORY11000 Kilo Bits.......................... MANDATORY6000 Kilo Bits........................... SUPPORTED9000 Kilo Bits........................... SUPPORTED12000 Kilo Bits.......................... SUPPORTED18000 Kilo Bits.......................... SUPPORTED24000 Kilo Bits.......................... SUPPORTED36000 Kilo Bits.......................... SUPPORTED48000 Kilo Bits.......................... SUPPORTED54000 Kilo Bits.......................... SUPPORTEDBeacon Period ............................. 100DTIM Period ............................... 1Fragmentation Threshold ................... 2346Multi Domain Capability Implemented ....... TRUEMulti Domain Capability Enabled ........... TRUECountry String ............................ USMulti Domain CapabilityConfiguration ............................. AUTOMATICFirst Chan Num ............................ 1Number Of Channels ........................ 11MAC Operation ParametersConfiguration ............................. AUTOMATICRTS Threshold ............................. 2347Short Retry Limit ......................... 7Long Retry Limit .......................... 4Fragmentation Threshold ................... 2346Maximum Tx MSDU Life Time ................. 512Maximum Rx Life Time....................... 512Tx PowerNum Of Supported Power Levels.............. 5Tx Power Level 1 .......................... 17 dBmTx Power Level 2........................... 14 dBmTx Power Level 3........................... 11 dBmTx Power Level 4........................... 8 dBmTx Power Level 5........................... 5 dBmTx Power Configuration..................... CUSTOMIZEDCurrent Tx Power Level..................... 5Phy OFDM parametersConfiguration.............................. CUSTOMIZEDCurrent Channel............................ 1TI Threshold............................... -50Legacy Tx Beamforming Configuration ....... CUSTOMIZEDLegacy Tx Beamforming ..................... ENABLEDAntenna Type............................... INTERNAL_ANTENNAInternal Antenna Gain (in5 dBm units)...... 11Diversity.................................. DIVERSITY_ENABLEDPerformance Profile ParametersConfiguration.............................. AUTOMATICInterference threshold..................... 10%Noise threshold............................ -70 dBmRF utilization threshold................... 80%Data-rate threshold........................ 1000000 bpsClient threshold........................... 12 clientsCoverage SNR threshold..................... 12 dBCoverage exception level................... 25%Client minimum exception level............. 3 clientsRogue Containment InformationContainment Count............................ 0This example shows how to display the general configuration of a Cisco access point:
> show ap config general cisco-apCisco AP Identifier.............................. 9Cisco AP Name.................................... cisco-apCountry code..................................... US - United StatesRegulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-AAP Country code.................................. US - United StatesAP Regulatory Domain............................. 802.11bg:-A 802.11a:-ASwitch Port Number .............................. 1MAC Address...................................... 12:12:12:12:12:12IP Address Configuration......................... DHCPIP Address....................................... 10.10.10.21IP NetMask....................................... 255.255.255.0CAPWAP Path MTU.................................. 1485Domain...........................................Name Server......................................Telnet State..................................... DisabledSsh State........................................ DisabledCisco AP Location................................ default locationCisco AP Group Name.............................. default-groupPrimary Cisco Switch Name........................ 4404Primary Cisco Switch IP Address.................. 10.10.10.32Secondary Cisco Switch Name......................Secondary Cisco Switch IP Address................ Not ConfiguredTertiary Cisco Switch Name....................... 4404Tertiary Cisco Switch IP Address................. 3.3.3.3Administrative State ............................ ADMIN_ENABLEDOperation State ................................. REGISTEREDMirroring Mode .................................. DisabledAP Mode ......................................... LocalPublic Safety ................................... Global: Disabled, Local: DisabledAP subMode ...................................... WIPSRemote AP Debug ................................. DisabledS/W Version .................................... 5.1.0.0Boot Version ................................... 12.4.10.0Mini IOS Version ................................ 0.0.0.0Stats Reporting Period .......................... 180LED State........................................ EnabledPoE Pre-Standard Switch.......................... EnabledPoE Power Injector MAC Addr...................... DisabledPower Type/Mode.................................. PoE/Low Power (degraded mode)Number Of Slots.................................. 2AP Model......................................... AIR-LAP1252AG-A-K9IOS Version...................................... 12.4(10:0)Reset Button..................................... EnabledAP Serial Number................................. serial_numberAP Certificate Type.............................. Manufacture InstalledManagement Frame Protection Validation........... Enabled (Global MFP Disabled)AP User Mode..................................... CUSTOMIZEDAP username..................................... mariaAP Dot1x User Mode............................... Not ConfiguredAP Dot1x username............................... Not ConfiguredCisco AP system logging host..................... 255.255.255.255AP Up Time....................................... 4 days, 06 h 17 m 22 sAP LWAPP Up Time................................. 4 days, 06 h 15 m 00 sJoin Date and Time............................... Mon Mar 3 06:19:47 2008Ethernet Port Duplex............................. AutoEthernet Port Speed.............................. AutoAP Link Latency.................................. EnabledCurrent Delay................................... 0 msMaximum Delay................................... 240 msMinimum Delay................................... 0 msLast updated (based on AP Up Time).............. 4 days, 06 h 17 m 20 s
Note
Related Commands
config ap
show ap config globalshow ap config global
To display the global syslog server settings for all access points that join the controller, use the show ap config global command.
show ap config global
Syntax Description
The command has no arguments and keywords.
Defaults
None.
Examples
This example shows how to display global syslog server settings:
> show ap config globalAP global system logging host.............................. 255.255.255.255Related Commands
show ap core-dump
To display the memory core dump information for a lightweight access point, use the show ap core-dump command.
show ap core-dump cisco_ap
Syntax Description
Defaults
None.
Examples
This example shows how to display memory core dump information:
> show ap core-dump AP02Memory core dump is disabled.Related Commands
config ap core-dump
show ap crash-file
show ap crash-file
To display the list of both crash and radio core dump files generated by lightweight access points, use the show ap crash-file command.
show ap crash-file
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the crash file generated by the access point:
> show ap crash-fileRelated Commands
config ap crash-file clear-all
config ap crash-file delete
config ap crash-file get-crash-file
config ap crash-file get-radio-core-dump
show ap data-plane
To display the data plane status for all access points or a specific access point, use the show ap data-plane command.
show ap data-plane {all | Cisco_AP}
Syntax Description
Defaults
None.
Examples
This example shows how to display the data plane status of all access points:
> show ap data-plane allMin Data Data Max Data LastAP Name Round Trip Round Trip Round Trip Update------------------ -------------- -------------- -------------- ------1130 0.000s 0.000s 0.002s 18:51:231240 0.000s 0.000s 0.000s 18:50:45
show ap eventlog
To display the contents of the event log file for an access point that is joined to the controller, use the show ap eventlog command.
show ap eventlog ap_name
Syntax Description
Defaults
None.
Examples
This example shows how to display the event log of an access point:
> show ap eventlog CiscoAPAP event log download has been initiatedWaiting for download to completeAP event log download completed.======================= AP Event log Contents =====================*Feb 13 11:54:17.146: %CAPWAP-3-CLIENTEVENTLOG: AP event log has been cleared from the contoller 'admin'*Feb 13 11:54:32.874: *** Access point reloading. Reason: Reload Command ****Mar 1 00:00:39.134: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source*Mar 1 00:00:39.174: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up*Mar 1 00:00:39.211: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up*Mar 1 00:00:49.947: %CAPWAP-3-CLIENTEVENTLOG: Did not get vendor specific options from DHCP....
show ap image
To display the detailed information about the predownloaded image for specified access points, use the
show ap image command.show ap image {cisco_ap | all}
Syntax Description
Note
Defaults
None.
Examples
This example shows how to display images present on all access points:
> show ap image allTotal number of APs.............................. 7Number of APsInitiated....................................... 4Predownloading.................................. 0Completed predownloading........................ 3Not Supported................................... 0Failed to Predownload........................... 0AP Name Primary Image Backup Image Status Version Next Retry Time Retry Count------------------ -------------- -------------- --------------- -------------- ----------AP1140-1 7.0.56.0 6.0.183.38 Complete 6.0.183.38 NA NAAP1140-2 7.0.56.0 6.0.183.58 Initiated 6.0.183.38 23:46:43 1AP1130-2 7.0.56.0 6.0.183.38 Complete 6.0.183.38 NA NAAP1130-3 7.0.56.0 6.0.183.58 Initiated 6.0.183.38 23:43:25 1AP1130-4 7.0.56.0 6.0.183.38 Complete 6.0.183.38 NA NAAP1130-5 7.0.56.0 6.0.183.58 Initiated 6.0.183.38 23:43:00 1AP1130-6 7.0.56.0 6.0.183.58 Initiated 6.0.183.38 23:41:33 1Related CommandsAP1130-6 7.0.56.0 6.0.183.58 Initiated 6.0.183.38 23:41:33 1
config ap image predownload
config ap image swap
show ap inventory
To display inventory information for an access point, use the show ap inventory command.
show ap inventory ap_name
Syntax Description
Defaults
None.
Examples
This example shows how to display the inventory of an access point:
> show ap inventory test101NAME: "test101" , DESCR: "Cisco Wireless Access Point"
PID: AIR-LAP1131AG-A-K9 , VID: V01, SN: FTX1123T2XX
show ap join stats detailed
To display all join-related statistics collected for a specific access point, use the show ap join stats detailed command.
show ap join stats detailed ap_mac
Syntax Description
Defaults
None.
Examples
This example shows how to display join information for a specific access point trying to join the controller:
> show ap join stats detailed 00:0b:85:02:0d:20Discovery phase statistics- Discovery requests received.......................... 2- Successful discovery responses sent.................. 2- Unsuccessful discovery request processing............ 0- Reason for last unsuccessful discovery attempt....... Not applicable- Time at last successful discovery attempt............ Aug 21 12:50:23:335- Time at last unsuccessful discovery attempt.......... Not applicableJoin phase statistics- Join requests received............................... 1- Successful join responses sent....................... 1- Unsuccessful join request processing................. 1- Reason for last unsuccessful join attempt.............RADIUS authorization is pending for the AP- Time at last successful join attempt................. Aug 21 12:50:34:481- Time at last unsuccessful join attempt............... Aug 21 12:50:34:374Configuration phase statistics- Configuration requests received...................... 1- Successful configuration responses sent.............. 1- Unsuccessful configuration request processing........ 0- Reason for last unsuccessful configuration attempt... Not applicable- Time at last successful configuration attempt........ Aug 21 12:50:34:374- Time at last unsuccessful configuration attempt...... Not applicableLast AP message decryption failure details- Reason for last message decryption failure........... Not applicableLast AP disconnect details- Reason for last AP connection failure................ Not applicableLast join error summary- Type of error that occurred last..................... Lwapp join request rejected- Reason for error that occurred last.................. RADIUS authorization is pending for the AP- Time at which the last join error occurred........... Aug 21 12:50:34:374Related Commands
show ap join stats detailed
show ap join stats summary
show ap join stats summary all
show ap join stats summary
To display the last join error detail for a specific access point, use the show ap join stats summary command.
show ap join stats summary ap_mac
Syntax Description
Defaults
None.
Usage Guidelines
To obtain the MAC address of the 802.11 radio interface, enter the show interface command on the access point.
Examples
This example shows how to display specific join information for an access point:
> show ap join stats summary 00:0b:85:02:0d:20Is the AP currently connected to controller.......................... NoTime at which the AP joined this controller last time................ Aug 21 12:50:36:061Type of error that occurred last..................................... Lwapp join request rejectedReason for error that occurred last.................................. RADIUS authorization is pending for the APTime at which the last join error occurred........................... Aug 21 12:50:34:374Related Commands
show ap join stats detailed
show ap join stats summary all
show ap join stats summary all
To display the MAC addresses of all the access points that are joined to the controller or that have tried to join, use the show ap join stats summary all command.
show ap join stats summary all
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a summary of join information for all access points:
> show ap join stats summary allNumber of APs.............................................. 4Base Mac AP EthernetMac AP Name IP Address Status00:0b:85:57:bc:c0 00:0b:85:57:bc:c0 AP1130 10.10.163.217 Joined00:1c:0f:81:db:80 00:1c:63:23:ac:a0 AP1140 10.10.163.216 Not joined00:1c:0f:81:fc:20 00:1b:d5:9f:7d:b2 AP1 10.10.163.215 Joined00:21:1b:ea:36:60 00:0c:d4:8a:6b:c1 AP2 10.10.163.214 Not joinedRelated Commands
show ap join stats detailed
show ap join stats summary
show ap link-encryption
To display the MAC addresses of all the access points that are joined to the controller or that have tried to join, use the show ap link-encryption command.
show ap link-encryption {all | Cisco_AP}
Syntax Description
Defaults
None.
Examples
This example shows how to display the link encryption status of all access points:
> show ap link-encryption allEncryption Dnstream Upstream LastAP Name State Count Count Update------------------ --- -------- -------- ------1240 Dis 4406 237553 Never1130 En 2484 276308 19:31Related Commands
config ap link-encryption
config ap link-latency
show ap monitor-mode summary
To display the current channel-optimized monitor mode settings, use the show ap monitor-mode summary command.
show ap monitor-mode summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display current channel-optimized monitor mode settings:
> show ap monitor-mode summaryAP Name Ethernet MAC Status Scanning Channel List
------------------ ----------------- ---------- ----------------------
AP_004 xx:xx:xx:xx:xx:xx Tracking 1, 6, 11, 4
Related Commands
config ap mode
config ap monitor-modeshow ap stats
To display the statistics for a Cisco lightweight access point, use the show ap stats command.
show ap stats {802.11{a | b} | wlan} cisco_ap [tsm {client_mac | all}]
Syntax Description
Defaults
None.
Examples
This example shows how to display statistics of an access point for the 802.11b network:
> show ap stats 802.11b AP02Number Of Slots.................................. 2AP Name.......................................... 1140_LAP_1MAC Address...................................... c4:7d:4f:3a:35:53Radio Type....................................... RADIO_TYPE_80211b/gStats InformationNumber of Users................................ 3TxFragmentCount................................ 232095MulticastTxFrameCnt............................ 3834FailedCount.................................... 347196RetryCount..................................... 683429MultipleRetryCount............................. 21416FrameDuplicateCount............................ 0RtsSuccessCount................................ 20RtsFailureCount................................ 0AckFailureCount................................ 439834RxIncompleteFragment........................... 0MulticastRxFrameCnt............................ 0FcsErrorCount.................................. 5845734TxFrameCount................................... 232095WepUndecryptableCount.......................... 0TxFramesDropped................................ 22Call Admission Control (CAC) StatsVoice Bandwidth in use(% of config bw)......... 50Total channel MT free........................ 0Total voice MT free.......................... 0Na Direct.................................... 0Na Roam...................................... 0Video Bandwidth in use(% of config bw)......... 0WMM TSPEC CAC Call StatsTotal num of voice calls in progress........... 1Num of roaming voice calls in progress......... 1Total Num of voice calls since AP joined....... 13Total Num of roaming calls since AP joined..... 13Total Num of exp bw requests received.......... 0Total Num of exp bw requests admitted.......... 0Num of voice calls rejected since AP joined.... 0Num of roam calls rejected since AP joined..... 1Num of calls rejected due to insufficent bw.... 0Num of calls rejected due to invalid params.... 0Num of calls rejected due to PHY rate.......... 0Num of calls rejected due to QoS policy........ 0SIP CAC Call StatsTotal Num of calls in progress................. 1Num of roaming calls in progress............... 0Total Num of calls since AP joined............. 29Total Num of roaming calls since AP joined..... 2Total Num of calls rejected(Insuff BW)......... 0Total Num of roam calls rejected(Insuff BW).... 0Total Num of calls rejected(Max call limit).... 9Total Num of roam calls rejected(Max call l.... 0Total Num of calls rejected(QoS Policy)........ 0Band Select StatsNum of dual band client ....................... 0Num of dual band client added.................. 0Num of dual band client expired ............... 0Num of dual band client replaced............... 0Num of dual band client detected .............. 0Num of suppressed client ...................... 0Num of suppressed client expired............... 0Num of suppressed client replaced.............. 0Related Commands
config ap static-ip
config ap stats-timershow ap summary
To display a summary of all lightweight access points attached to the controller, use the show ap summary command.
show ap summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Usage Guidelines
A list that contains each lightweight access point name, number of slots, manufacturer, MAC address, location, and the controller port number appears.
Examples
This example shows how to display a summary of all connected access points:
> show ap summaryNumber of APs.................................... 2Global AP username.............................. userGlobal AP Dot1x username........................ Not ConfiguredNumber of APs.................................... 2Global AP username.............................. userGlobal AP Dot1x username........................ Not ConfiguredAP Name Slots AP Model Ethernet MAC Location Port Country Priority-------- ----- ---------------- ----------------- ---------- ---- ------- --------wolverine 2 AIR-LAP1252AG-A-K9 00:1b:d5:13:39:74 Reception 1 US 3ap:1120 1 AIR-LAP1121G-A-K9 00:1b:d5:a9:ad:08 Hall 235 1 US 1Related Commands
show ap tcp-mss-adjust
To display the Basic Service Set Identifier (BSSID) value for each WLAN defined on an access point, use the show ap tcp-mss-adjust command.
show ap tcp-mss-adjust {cisco_ap | all}
Syntax Description
Note
Defaults
None.
Examples
This example shows how to display Transmission Control Protocol (TCP) maximum segment size (MSS) information of all access points:
> show ap tcp-mss-adjust allAP Name TCP State MSS Size------------------ --------- -------AP-1140 enabled 536AP-1240 disabled -AP-1130 disabled -Related Commands
show ap wlan
To display the Basic Service Set Identifier (BSSID) value for each WLAN defined on an access point, use the show ap wlan command.
show ap wlan 802.11{a | b} cisco_ap
Syntax Description
802.11a
Specifies the 802.11a network.
802.11b
Specifies the 802.11b/g network.
ap_name
Specifies the lightweight access point name.
Defaults
None.
Examples
This example shows how to display BSSIDs of an access point for the 802.11b network:
> show ap wlan 802.11b AP01Site Name........................................ MY_AP_GROUP1Site Description................................. MY_AP_GROUP1WLAN ID Interface BSSID------- ----------- --------------------------1 management 00:1c:0f:81:fc:202 dynamic 00:1c:0f:81:fc:21Related Commands
show arp switch
To display the Cisco wireless LAN controller MAC addresses, IP addresses, and port types, use the show arp switch command.
show arp switch
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display Address Resolution Protocol (ARP) cache information for the switch:
> show arp switchMAC Address IP Address Port VLAN Type------------------- ---------------- ------------ ---- -------------------xx:xx:xx:xx:xx:xx xxx.xxx.xxx.xxx service port 1xx:xx:xx:xx:xx:xx xxx.xxx.xxx.xxx service portxx:xx:xx:xx:xx:xx xxx.xxx.xxx.xxx service portRelated Commands
show auth-list
To display the access point authorization list, use the show auth-list command.
show auth-list
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the access point authorization list:
> show auth-listAuthorize APs against AAA...................... disabledAllow APs with Self-signed Certificate (SSC)... disabledMac Addr Cert Type Key Hash----------------------- ---------- ------------------------------------------xx:xx:xx:xx:xx:xx MICRelated Commands
clear tacacs auth statistics
clear stats local-auth
config auth-list add
config auth-list ap-policy
config auth-list deleteshow boot
To display the primary and backup software build numbers with an indication of which is active, use the show boot command.
show boot
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Usage Guidelines
Each Cisco wireless LAN controller retains one primary and one backup operating system software load in nonvolatile RAM to allow controllers to boot off the primary load (default) or revert to the backup load when desired.
Examples
This example shows how to display the default boot image information:
> show bootPrimary Boot Image............................... 3.2.13.0 (active)Backup Boot Image................................ 3.2.15.0Related Commands
show call-control ap
Note
To see the metrics for successful calls or the traps generated for failed calls, use the show call-control ap command.
show call-control ap {802.11a | 802.11b} Cisco_ap {metrics | traps}
Syntax Description
Defaults
None.
Examples
This example shows how to display the metrics for successful calls generated for an access point:
> show call-control ap 802.11a Cisco_AP metricsTotal Call Duration in Seconds................... 120Number of Calls.................................. 10Number of calls for given client is................. 1This example shows how to display the metrics for the traps generated for an access point:
> show call-control ap 802.11a Cisco_AP trapsNumber of traps sent in one min.................. 2Last SIP error code.............................. 404Last sent trap timestamp...................... Jun 20 10:05:06Usage Guidelines
To aid in troubleshooting, the output of this command shows an error code for any failed calls. Table 2-1 explains the possible error codes for failed calls.
show call-control client
To see call information for a call-aware client when Voice-over-IP (VoIP) snooping is enabled and the call is active, use the show call-control client command
show call-control client callInfo client_MAC_address
Syntax Description
Defaults
None.
Examples
This example shows how to display the call information such as the IP port for calls related to the client:
> show call-control client callInfo 10.10.10.10.10.10Uplink IP/port................................... 0.0.0.0 / 0Downlink IP/port................................ 9.47.96.107 / 5006UP............................................... 6Calling Party.................................... sip:1021Called Party..................................... sip:1000Call ID.......................................... 38423970c3fca477Call on hold: ................................... FALSENumber of calls for given client is.............. 1Related Commands
show capwap client config
To display the list of clients associated with the capwap access point, use the show capwap client command.
show capwap client config
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display clients associated with capwap access point:
> show capwap client configconfigMagicMark 0xF1E2D3C4chkSumV2 23845chkSumV1 43434swVer 4.2.37.156adminState ADMIN_ENABLED(1)name AP001b.0cfc.3f80location default locationgroup namemwarName WLC1mwarIPAddress 9.41.80.67mwarNamemwarIPAddress 0.0.0.0mwarNamemwarIPAddress 0.0.0.0ssh status DisabledTelnet status DisablednumOfSlots 2spamRebootOnAssert 1spamStatTimer 180randSeed 0x0transport SPAM_TRANSPORT_L3(2)transportCfg SPAM_TRANSPORT_DEFAULT(0)initialisation SPAM_PRODUCTION_DISCOVERY(1)Related Commands
capwap ap ip address
capwap ap ip default-gateway
show capwap client ip configshow capwap client ip config
To display the capwap static IP configuration, use the show capwap client ip config command.
show capwap client ip config
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the capwap static IP information:
> show capwap client configLWAPP Static IP ConfigurationPrimary Controller 9.41.80.88Related Commands
capwap ap controller ip address
capwap ap ip address
show capwap client config
show capwap reap association
To display the list of clients associated to an access point and their Service Set Identifiers (SSIDs), use the show capwap reap association command.
show capwap reap association
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display clients associated to an access point and their SSIDs:
> show capwap reap associationRelated Commands
config hreap group
show capwap reap statusshow capwap reap status
To display the status of the hybrid-REAP access point (connected or standalone), use the show capwap reap status command.
show capwap reap status
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the status of the hybrid-REAP access point:
> show capwap reap statusRelated Commands
config hreap group
show capwap reap associationshow certificate compatibility
To display whether or not certificates are verified as compatible in the Cisco wireless LAN controller, use the show certificate compatibility command.
show certificate compatibility
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the status of the compatibility mode:
> show certificate compatibilityCertificate compatibility mode:................ offRelated Commands
config certificate
config certificate lsc
show certificate lsc
show certificate summary
show local-auth certificatesshow certificate lsc
To verify that the controller has generated a Locally Significant Certificate (LSC), use the show certificate lsc summary command.
show certificate lsc {summary | ap-provision}
Syntax Description
summary
Displays summary of LSC certificate settings and certificates.
ap-provision
Displays details about the access points that are provisioned using the LSC.
Defaults
None.
Examples
This example shows how to display a summary of the LSC:
> show certificate lsc summaryLSC Enabled...................................... YesLSC CA-Server.................................... http://10.0.0.1:8080/caserverLSC AP-Provisioning.............................. YesProvision-List............................... Not ConfiguredLSC Revert Count in AP reboots............... 3LSC Params:Country...................................... 4State........................................ caCity......................................... ssOrgn......................................... orgDept......................................... depEmail........................................ dep@co.comKeySize...................................... 390LSC Certs:CA Cert...................................... Not ConfiguredRA Cert...................................... Not ConfiguredThis example shows how to display the details about the access points that are provisioned using the LSC:
> show certificate lsc ap-provisionLSC AP-Provisioning.............................. YesProvision-List................................... PresentIdx Mac Address--- -------------1 00:18:74:c7:c0:90Related Commands
config certificate
config certificate lsc
show certificate compatibility
show certificate summary
show local-auth certificatesshow certificate summary
To verify that the controller has generated a certificate, use the show certificate summary command.
show certificate summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a summary of the certificate:
> show certificate summaryWeb Administration Certificate................. Locally GeneratedWeb Authentication Certificate................. Locally GeneratedCertificate compatibility mode:................ offRelated Commands
config certificate
config certificate lsc
show certificate compatibility
show certificate lsc
show local-auth certificatesShow Client Commands
Use the show client commands to display client settings.
show client ap
To display the clients on a Cisco lightweight access point, use the show client ap command.
show client ap 802.11{a | b} cisco_ap
Syntax Description
802.11a
Specifies the 802.11a network.
802.11b
Specifies the 802.11b/g network.
cisco_ap
Cisco lightweight access point name.
Defaults
None.
Usage Guidelines
The show client ap command may list the status of automatically disabled clients. Use the show exclusionlist command to view clients on the exclusion list (blacklisted).
Examples
This example shows how to display client information on an access point:
> show client ap 802.11b AP1MAC Address AP Id Status WLAN Id Authenticated----------------- ------ ------------- --------- -------------xx:xx:xx:xx:xx:xx 1 Associated 1 NoRelated Commands
show client detail
show client summary
show client username
show country
show exclusionlist
show client ccx client-capability
To display the client's capability information, use the show client ccx client-capability command.
show client ccx client-capability client_mac_address
Syntax Description
Defaults
None.
Usage Guidelines
This command displays the client's available capabilities, not the current settings for the capabilities.
Examples
This example shows how to display the client's capability:
> show client ccx client-capability 00:40:96:a8:f7:98Service Capability.................................. Voice, Streaming(uni-directional) Video, Interactive(bi-directional) VideoRadio Type.......................................... DSSS OFDM(802.11a) HRDSSS(802.11b) ERP(802.11g)Radio Type.......................................... DSSSRadio Channels.................................. 1 2 3 4 5 6 7 8 9 10 11Tx Power Mode................................... AutomaticRate List(MB)................................... 1.0 2.0Radio Type.......................................... HRDSSS(802.11b)Radio Channels.................................. 1 2 3 4 5 6 7 8 9 10 11Tx Power Mode................................... AutomaticRate List(MB)................................... 5.5 11.0Radio Type.......................................... ERP(802.11g)Radio Channels.................................. 1 2 3 4 5 6 7 8 9 10 11Tx Power Mode................................... AutomaticRate List(MB)................................... 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0Are you sure you want to start? (y/N)y Are you sure you want to start? (y/N)Related Commands
config client ccx get-client-capability
config client ccx get-operating-parameters
config client ccx get-profiles
config client ccx stats-request
show client ccx operating-parameters
show client ccx profiles
show client ccx stats-reportshow client ccx frame-data
To display the data frames sent from the client for the last test, use the show client ccx frame-data command.
show client ccx frame-data client_mac_address
Syntax Description
Defaults
None.
Examples
This example shows how to display the data frame sent from the client for the last test:
> show client ccx frame-data xx:xx:xx:xx:xx:xxshow client ccx last-response-status
To display the status of the last test response, use the show client ccx last-response-status command.
show client ccx last-response-status client_mac_address
Syntax Description
Defaults
None.
Examples
This example shows how to display the status of the last test response:
> show client ccx last-response-status Test Status ........................ SuccessResponse Dialog Token.............. 87Response Status.................... SuccessfulResponse Test Type................. 802.1x Authentication TestResponse Time...................... 3476 seconds since system bootRelated Commands
config client ccx clear-reports
config client ccx clear-results
config client ccx default-gw-ping
config client ccx dhcp-test
config client ccx log-request
show client ccx last-response-status
show client ccx last-test-statusshow client ccx last-test-status
To display the status of the last test, use the show client ccx last-test-status command.
show client ccx last-test-status client_mac_address
Syntax Description
Defaults
None.
Examples
This example shows how to display the status of the last test of the client:
> show client ccx last-test-statusTest Type ........................ Gateway Ping TestTest Status ...................... Pending/Success/TimeoutDialog Token ..................... 15Timeout .......................... 15000 msRequest Time ..................... 1329 seconds since system bootRelated Commands
config client ccx clear-reports
config client ccx clear-results
config client ccx default-gw-ping
config client ccx dhcp-test
config client ccx log-request
show client ccx last-response-status
show client ccx log-response
To display a log response, use the show client ccx log-response command.
show client ccx log-response {roam | rsna | syslog} client_mac_address
Syntax Description
Defaults
None.
Examples
This example shows how to display the system log response:
> show client ccx log-response syslog 00:40:96:a8:f7:98Tue Jun 26 18:07:48 2007 Syslog Response LogID=131: Status=SuccessfulEvent Timestamp=0d 00h 19m 42s 278987usClient SysLog = `<11> Jun 19 11:49:47 unraval13777 Mandatory elements missing in the OID response'Event Timestamp=0d 00h 19m 42s 278990usClient SysLog = `<11> Jun 19 11:49:47 unraval13777 Mandatory elements missing in the OID response'Tue Jun 26 18:07:48 2007 Syslog Response LogID=131: Status=SuccessfulEvent Timestamp=0d 00h 19m 42s 278987usClient SysLog = `<11> Jun 19 11:49:47 unraval13777 Mandatory elements missing in the OID response'Event Timestamp=0d 00h 19m 42s 278990usClient SysLog = `<11> Jun 19 11:49:47 unraval13777 Mandatory elements missing in the OID response'This example shows how to display the client roaming log response:
> show client ccx log-response roam 00:40:96:a8:f7:98Thu Jun 22 11:55:14 2007 Roaming Response LogID=20: Status=SuccessfulEvent Timestamp=0d 00h 00m 13s 322396usSource BSSID=00:40:96:a8:f7:98, Target BSSID=00:0b:85:23:26:70,Transition Time=100(ms)Transition Reason: Normal roam, poor linkTransition Result: SuccessThu Jun 22 11:55:14 2007 Roaming Response LogID=133: Status=SuccessfulEvent Timestamp=0d 00h 00m 16s 599006usSource BSSID=00:0b:85:81:06:c2, Target BSSID=00:0b:85:81:06:c2,Transition Time=3235(ms)Transition Reason: Normal roam, poor linkTransition Result: SuccessThu Jun 22 18:28:48 2007 Roaming Response LogID=133: Status=SuccessfulEvent Timestamp=0d 00h 00m 08s 815477usSource BSSID=00:0b:85:81:06:c2, Target BSSID=00:0b:85:81:06:d2,Transition Time=3281(ms)Transition Reason: First association to WLANTransition Result: SuccessRelated Commands
show client ccx manufacturer-info
To display the client manufacturing information, use the show client ccx manufacturer-info command.
show client ccx manufacturer-info client_mac_address
Syntax Description
Defaults
None.
Examples
This example shows how to display the client manufacturing information:
> show client ccx manufacturer-info 00:40:96:a8:f7:98Manufacturer OUI .............................. 00:40:96Manufacturer ID ............................... CiscoManufacturer Model ............................ Cisco Aironet 802.11a/b/g Wireless AdapterManufacturer Serial ........................... FOC1046N3SXMac Address ................................... 00:40:96:b2:8d:5eRadio Type .................................... DSSS OFDM(802.11a) HRDSSS(802.11b)ERP(802.11g)Antenna Type .................................. Omni-directional diversityAntenna Gain .................................. 2 dBiRx Sensitivity:Radio Type ...................................... DSSSRx Sensitivity .................................. Rate:1.0 Mbps, MinRssi:-95, MaxRss1:-30Rx Sensitivity .................................. Rate:2.0 Mbps, MinRssi:-95, MaxRss1:-30Radio Type ...................................... HRDSSS(802.11b)Rx Sensitivity .................................. Rate:5.5 Mbps, MinRssi:-95, MaxRss1:-30Rx Sensitivity .................................. Rate:11.0 Mbps, MinRssi:-95, MaxRss1:-30Radio Type ...................................... ERP(802.11g)Rx Sensitivity .................................. Rate:6.0 Mbps, MinRssi:-95, MaxRss1:-30Rx Sensitivity .................................. Rate:9.0 Mbps, MinRssi:-95, MaxRss1:-30Rx Sensitivity .................................. Rate:12.0 Mbps, MinRssi:-95, MaxRss1:-30Rx Sensitivity .................................. Rate:18.0 Mbps, MinRss1:-95, MaxRss1:-30Related Commands
config client ccx get-client-capability
config client ccx get-manufacturer-info
config client ccx get-operating-parameters
config client ccx get-profiles
show client ccx operating-parameters
To display the client operating-parameters, use the show client ccx operating-parameters command.
show client ccx operating-parameters client_mac_address
Syntax Description
Defaults
None.
Examples
This example shows how to display the client operating parameters:
> show client ccx operating-parameters 00:40:96:a8:f7:98Client Mac ......................................... 00:40:96:b2:8d:5eRadio Type ......................................... OFDM(802.11a)Radio Type ......................................... OFDM(802.11a)Radio Channels ................................. 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140 149 153 157 161 165Tx Power Mode .................................. AutomaticRate List(MB)................................... 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0Power Save Mode .................................... Normal Power SaveSSID ............................................... wifiSecurity Parameters[EAP Method, Credential]......... NoneAuth Method ........................................ NoneKey Management...................................... NoneEncryption ......................................... NoneDevice Name ........................................ Wireless Network Connection 15Device Type ........................................ 0OS Id .............................................. Windows XPOS Version ......................................... 5.1.6.2600 Service Pack 2IP Type ............................................ DHCP addressIPv4 Address ....................................... AvailableIP Address ......................................... 70.0.4.66Subnet Mask ........................................ 255.0.0.0Default Gateway .................................... 70.1.0.1IPv6 Address ....................................... Not AvailableIPv6 Address ....................................... 0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:IPv6 Subnet Mask ................................... 0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:DNS Servers ........................................ 103.0.48.0WINS Servers .......................................System Name ........................................ URAVAL3777Firmware Version ................................... 4.0.0.187Driver Version ..................................... 4.0.0.187Related Commands
config client ccx get-client-capability
config client ccx get-manufacturer-info
config client ccx get-operating-parameters
config client ccx get-profilesshow client ccx profiles
To display the client profiles, use the show client ccx profiles command.
show client ccx profiles client_mac_address
Syntax Description
Defaults
None.
Examples
This example shows how to display the client profiles:
> show client ccx profiles 00:40:96:a8:f7:98Number of Profiles .................................. 1Current Profile ..................................... 1Profile ID .......................................... 1Profile Name ........................................ wifiEAPSSID ................................................ wifiEAPSecurity Parameters [EAP Method, Credential]......... EAP-TLS, Host OS Login CredentialsAuth Method ......................................... EAPKey Management ...................................... WPA2+CCKMEncryption .......................................... AES-CCMPPower Save Mode ..................................... Constantly AwakeRadio Configuration:Radio Type........................................... DSSSPreamble Type.................................... Long preambleCCA Method....................................... Energy Detect + CarrierDetect/CorrelationData Retries..................................... 6Fragment Threshold............................... 2342Radio Channels................................... 1 2 3 4 5 6 7 8 9 10 11Tx Power Mode.................................... AutomaticRate List (MB)................................... 1.0 2.0Radio Type........................................... HRDSSS(802.11b)Preamble Type.................................... Long preambleCCA Method....................................... Energy Detect + CarrierDetect/CorrelationData Retries..................................... 6Fragment Threshold............................... 2342Radio Channels................................... 1 2 3 4 5 6 7 8 9 10 11Tx Power Mode.................................... AutomaticRate List(MB).................................... 5.5 11.0Radio Type........................................... ERP(802.11g)Preamble Type.................................... Long preambleCCA Method....................................... Energy Detect + CarrierDetect/CorrelationData Retries..................................... 6Fragment Threshold............................... 2342Radio Channels................................... 1 2 3 4 5 6 7 8 9 10 11Tx Power Mode.................................... AutomaticRate List (MB)................................... 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0Radio Type........................................... OFDM(802.11a)Preamble Type.................................... Long preambleCCA Method....................................... Energy Detect + CarrierDetect/CorrelationData Retries..................................... 6Fragment Threshold............................... 2342Radio Channels................................... 36 40 44 48 52 56 60 64 149 153 157 161 165Tx Power Mode.................................... AutomaticRate List (MB)................................... 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0Related Commands
config client ccx get-client-capability
config client ccx get-manufacturer-info
config client ccx get-operating-parameters
config client ccx get-profilesshow client ccx results
To display the results from the last successful diagnostic test, use the show client ccx results command.
show client ccx results client_mac_address
Syntax Description
Defaults
None.
Examples
This example shows how to display the results from last successful diagnostic test:
> show client ccs results xx.xx.xx.xxdot1x Complete....................................... SuccessEAP Method........................................... *1,Host OS Login Credentialsdot1x Status......................................... 255Related Commands
config client ccx test-abort
config client ccx test-association
config client ccx test-dot1x
config client ccx test-profile
config client ccx clear-reports
config client ccx clear-resultsshow client ccx rm
To display Cisco Client eXtension (CCX) client radio management report information, use the show client ccx rm commands.
show client ccx rm client_MAC {status |
report (chan-load | noise-hist | frame request | beacon | frame)}Syntax Description
Defaults
None.
Examples
This example shows how to display the client radio management status information:
> show client ccx rm 00:40:96:15:21:ac statusClient Mac Address............................... 00:40:96:15:21:ac Channel Load Request............................. Enabled Noise Histogram Request.......................... Enabled Beacon Request................................... Enabled Frame Request.................................... Enabled Interval......................................... 30 Iteration........................................... 10This example shows how to display the client radio management load reports:
> show client ccx rm 00:40:96:15:21:ac report chan-loadChannel Load Report Client Mac Address............................... 00:40:96:ae:53:bc Timestamp........................................ 788751121 Incapable Flag................................... On Refused Flag........................................ OnChan CCA Busy Fraction ----------------------- 1 194 2 86 3 103 4 0 5 178 6 82 7 103 8 95 9 13 10 222 11 75This example shows how to display the client radio management noise histogram reports:
> show client ccx rm 00:40:96:15:21:ac report noise-hist Noise Histogram Report Client Mac Address............................... 00:40:96:15:21:ac Timestamp........................................ 4294967295 Incapable Flag................................... Off Refused Flag........................................ OffChan RPI0 RPI1 RPI2 RPI3 RPI4 RPI5 RPI6 RPI7Related Commands
config client ccx default-gw-ping
config client ccx dhcp-testshow client ccx stats-report
To display the Cisco Client eXtensions (CCX) statistics report from a specified client device, use the show client ccx stats-report command.
show client ccx stats-report client_mac_address
Syntax Description
Defaults
None.
Examples
This example shows how to displays the statistics report:
> show client ccx stats-report 00:40:96:a8:f7:98Measurement duration = 1dot11TransmittedFragmentCount = 1dot11MulticastTransmittedFrameCount = 2dot11FailedCount = 3dot11RetryCount = 4dot11MultipleRetryCount = 5dot11FrameDuplicateCount = 6dot11RTSSuccessCount = 7dot11RTSFailureCount = 8dot11ACKFailureCount = 9dot11ReceivedFragmentCount = 10dot11MulticastReceivedFrameCount = 11dot11FCSErrorCount = 12dot11TransmittedFrameCount = 13Related Commands
config client ccx default-gw-ping
config client ccx dhcp-test
config client ccx dns-ping
show client detail
To display detailed information for a client on a Cisco lightweight access point, use the show client detail command.
show client detail mac_address
Syntax Description
Defaults
None.
Usage Guidelines
The show client ap command may list the status of automatically disabled clients. Use the show exclusionlist command to display clients on the exclusion list (blacklisted).
Note
Examples
This example shows how to display the client detailed information:
> show client detail 00:0c:41:07:33:a6Client MAC Address............................... 00:16:36:40:ac:58Client Username.................................. N/AClient State..................................... AssociatedClient NAC OOB State............................. QUARANTINEGuest LAN Id..................................... 1IP Address....................................... UnknownSession Timeout.................................. 0QoS Level........................................ GoldDiff Serv Code Point (DSPC)...................... disabledMobility State................................... LocalInternal Mobility State.......................... apfMsMmInitialSecurity Policy Completed........................ NoPolicy Manager State............................. WEBAUTH_REQDPolicy Manager Rule Created...................... YesNPU Fast Fast Notified........................... YesLast Policy Manager State........................ WEBAUTH_REQDClient Entry Create Time......................... 460 secondsInterface........................................ wired-guestVLAN............................................. 236Quarantine VLAN.................................. 0Client Statistics:Number of Bytes Received..................... 0Number of Bytes Sent......................... 0Number of Packets Received................... 0Number of Packets Sent....................... 0Number of EAP Id Request Msg Timeouts........ 0Number of EAP Id Request Msg Failures........ 0Number of EAP Request Msg Timeouts........... 2Number of EAP Request Msg Failures........... 1Number of EAP Key Msg Timeouts............... 0Number of EAP Key Msg Failures............... 0Number of Policy Errors...................... 0Radio Signal Strength Indicator.............. UnavailableSignal to Noise Ratio........................ Unavailable...Related Commands
show client location-calibration summary
To display client location calibration summary information, use the show client location-calibration summary command.
show client location-calibration summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the location calibration summary information:
> show client location-calibration summaryMAC Address Interval----------- ----------10:10:10:10:10:10 6021:21:21:21:21:21 45Related Commands
show client summary
show client summary guest-lanshow client probing
To display the number of probing clients, use the show client probing command.
show client probing
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the number of probing clients:
> show client probingNumber of Probing Clients........................ 0Related Commands
show client summary
show client summary guest-lanshow client roam-history
To display the roaming history of a specified client, use the show client roam-history command.
show client roam-history mac_address
Syntax Description
Defaults
None.
Examples
This example shows how to display the roaming history of a specified client:
> show client roam-history 00:14:6c:0a:57:77show client summary
To display a summary of clients associated with a Cisco lightweight access point, use the show client summary command.
show client summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Usage Guidelines
The show client ap command may list the status of automatically disabled clients. Use the show exclusionlist command to display clients on the exclusion list (blacklisted).
Examples
This example shows how to display a summary of the active clients:
> show client summaryNumber of Clients................................ 24MAC Address AP Name Status WLAN Auth Protocol Port----------------- ----------------- ------------- ---- ---- -------- ----xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11a 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11a 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11b 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11a 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11b 1xx:xx:xx:xx:xx:xx AP02 Associated 2 Yes 802.11b 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11b 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11b 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11b 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11a 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11a 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11b 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11a 1xx:xx:xx:xx:xx:xx AP02 Probing N/A No 802.11a 1Number of Clients................................ 2Related Commands
show client summary guest-lan
To display the active wired guest LAN clients, use the show client summary guest-lan command.
show client summary guest-lan
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a summary of the active wired guest LAN clients:> show client summary guest-lanNumber of Clients................................ 1MAC Address AP Name Status WLAN Auth Protocol Port Wired----------- --------- ---------- ---- ---- -------- ---- -----00:16:36:40:ac:58 N/A Associated 1 No 802.3 1 YesRelated Commands
show client tsm
To display the client traffic stream metrics (TSM) statistics, use the show client tsm command.
show client tsm 802.11 {a | b} client_mac {ap_mac | all}
Syntax Description
Defaults
None.
Examples
This example shows how to display the client's TSM for the 802.11a network:
> show client tsm 802.11a xx:xx:xx:xx:xx:xx allAP Interface MAC: 00:0b:85:01:02:03Client Interface Mac: 00:01:02:03:04:05Measurement Duration: 90 secondsTimestamp 1st Jan 2006, 06:35:80UpLink Stats================Average Delay (5sec intervals)............................35Delay less than 10 ms.....................................20Delay bet 10 - 20 ms......................................20Delay bet 20 - 40 ms......................................20Delay greater than 40 ms..................................20Total packet Count.........................................80Total packet lost count (5sec).............................10Maximum Lost Packet count(5sec)............................5Average Lost Packet count(5secs)...........................2DownLink Stats================Average Delay (5sec intervals)............................35Delay less than 10 ms.....................................20Delay bet 10 - 20 ms......................................20Delay bet 20 - 40 ms......................................20Delay greater than 40 ms..................................20Total packet Count.........................................80Total packet lost count (5sec).............................10Maximum Lost Packet count(5sec)............................5Average Lost Packet count(5secs)...........................2Related Commands
show client ap
show client detail
show client summaryshow client username
To display the client data by the username, use the show client username command.
show client username username
Syntax Description
Defaults
None.
Examples
This example shows how to display the detailed information for a client by name:
> show client username IT_007MAC Address AP ID Status WLAN Id Authenticated----------------- ------ ------------- --------- -------------xx:xx:xx:xx:xx:xx 1 Associated 1 NoRelated Commands
show client ap
show client detail
show client summaryshow country
To display the configured country and the radio types supported, use the show country command.
show country
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the configured countries and supported radio types:
> show countryConfigured Country............................. United StatesConfigured Country CodesUS - United States............................. 802.11a / 802.11b / 802.11gRelated Commands
config country
show country channels
show country supported
show country channels
To display the radio channels supported in the configured country, use the show country channels command.
show country channels
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the auto-RF channels for the configured countries:> show country channelsConfigured Country............................. United StatesKEY: * = Channel is legal in this country and may be configured manually.A = Channel is the Auto-RF default in this country.. = Channel is not legal in this country.C = Channel has been configured for use by Auto-RF.x = Channel is available to be configured for use by Auto-RF.---------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-802.11BG :Channels : 1 1 1 1 1: 1 2 3 4 5 6 7 8 9 0 1 2 3 4---------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-US : A * * * * A * * * * A . . .---------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-802.11A : 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1Channels : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6: 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5---------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-US : . A . A . A . A A A A A * * * * * . . . * * * A A A A *---------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-Related Commands
config country
show country
show country supportedshow country supported
To display a list of the supported country options, use the show country supported command.
show country supported
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a list of all the supported countries:
> show country supportedConfigured Country............................. United StatesSupported Country CodesAR - Argentina................................. 802.11a / 802.11b / 802.11gAT - Austria................................... 802.11a / 802.11b / 802.11gAU - Australia................................. 802.11a / 802.11b / 802.11gBR - Brazil.................................... 802.11a / 802.11b / 802.11gBE - Belgium................................... 802.11a / 802.11b / 802.11gBG - Bulgaria.................................. 802.11a / 802.11b / 802.11gCA - Canada.................................... 802.11a / 802.11b / 802.11gCH - Switzerland............................... 802.11a / 802.11b / 802.11gCL - Chile..................................... 802.11b / 802.11gCN - China..................................... 802.11a / 802.11b / 802.11gCO - Colombia.................................. 802.11b / 802.11gCY - Cyprus.................................... 802.11a / 802.11b / 802.11gCZ - Czech Republic............................ 802.11a / 802.11bDE - Germany................................... 802.11a / 802.11b / 802.11gDK - Denmark................................... 802.11a / 802.11b / 802.11gEE - Estonia................................... 802.11a / 802.11b / 802.11gES - Spain..................................... 802.11a / 802.11b / 802.11gFI - Finland................................... 802.11a / 802.11b / 802.11gFR - France.................................... 802.11a / 802.11b / 802.11gGB - United Kingdom............................ 802.11a / 802.11b / 802.11gGI - Gibraltar................................. 802.11a / 802.11b / 802.11gGR - Greece.................................... 802.11a / 802.11b / 802.11gHK - Hong Kong................................. 802.11a / 802.11b / 802.11gHU - Hungary................................... 802.11a / 802.11b / 802.11gID - Indonesia................................. 802.11b / 802.11gIE - Ireland................................... 802.11a / 802.11b / 802.11gIN - India..................................... 802.11a / 802.11b / 802.11gIL - Israel.................................... 802.11a / 802.11b / 802.11gILO - Israel (outdoor).......................... 802.11b / 802.11gIS - Iceland................................... 802.11a / 802.11b / 802.11gIT - Italy..................................... 802.11a / 802.11b / 802.11gJP - Japan (J)................................. 802.11a / 802.11b / 802.11gJ2 - Japan 2(P)................................ 802.11a / 802.11b / 802.11gJ3 - Japan 3(U)................................ 802.11a / 802.11b / 802.11gKR - Korea Republic (C)........................ 802.11a / 802.11b / 802.11gKE - Korea Extended (K)........................ 802.11a / 802.11b / 802.11gLI - Liechtenstein............................. 802.11a / 802.11b / 802.11gLT - Lithuania................................. 802.11a / 802.11b / 802.11gLU - Luxembourg................................ 802.11a / 802.11b / 802.11gLV - Latvia.................................... 802.11a / 802.11b / 802.11gMC - Monaco.................................... 802.11a / 802.11b / 802.11gMT - Malta..................................... 802.11a / 802.11b / 802.11gMX - Mexico.................................... 802.11a / 802.11b / 802.11gMY - Malaysia.................................. 802.11a / 802.11b / 802.11gNL - Netherlands............................... 802.11a / 802.11b / 802.11gNZ - New Zealand............................... 802.11a / 802.11b / 802.11gNO - Norway.................................... 802.11a / 802.11b / 802.11gPA - Panama.................................... 802.11b / 802.11gPE - Peru...................................... 802.11b / 802.11gPH - Philippines............................... 802.11a / 802.11b / 802.11gPL - Poland.................................... 802.11a / 802.11b / 802.11gPT - Portugal.................................. 802.11a / 802.11b / 802.11gRU - Russian Federation........................ 802.11a / 802.11b / 802.11gRO - Romania................................... 802.11a / 802.11b / 802.11gSA - Saudi Arabia.............................. 802.11a / 802.11b / 802.11gSE - Sweden.................................... 802.11a / 802.11b / 802.11gSG - Singapore................................. 802.11a / 802.11b / 802.11gSI - Slovenia.................................. 802.11a / 802.11b / 802.11gSK - Slovak Republic........................... 802.11a / 802.11b / 802.11gTH - Thailand.................................. 802.11b / 802.11gTR - Turkey.................................... 802.11b / 802.11gTW - Taiwan.................................... 802.11a / 802.11b / 802.11gUA - Ukraine................................... 802.11a / 802.11b / 802.11gUS - United States............................. 802.11a / 802.11b / 802.11gUSL - United States (Legacy).................... 802.11a / 802.11b / 802.11gUSX - United States (US + chan165).............. 802.11a / 802.11b / 802.11gVE - Venezuela................................. 802.11b / 802.11gZA - South Africa.............................. 802.11a / 802.11b / 802.11gRelated Commands
config country
show country
show country channelsshow coredump summary
To display a summary of the controller's core dump file, use the show coredump summary command.
show coredump summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the core dump summary:
> show coredump summaryCore Dump is enabledFTP Server IP.................................... 10.10.10.17FTP Filename..................................... file1FTP Username..................................... ftpuserFTP Password.................................. *********Related Commands
config coredump
config coredump ftp
config coredump usernameshow cpu
To display current WLAN controller CPU usage information, use the show cpu command.
show cpu
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the current CPU usage information:> show cpuCurrent CPU load: 2.50%show custom-web
To display web authentication customization information, use the show custom-web command.
show custom-web
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the web authentication customization information:
> show custom-webRadius Authentication Method..................... PAPCisco Logo....................................... EnabledCustomLogo....................................... NoneCustom Title..................................... NoneCustom Message................................... NoneCustom Redirect URL.............................. NoneExternal web authentication Mode................. DisabledExternal web authentication URL.................. NoneRelated Commands
config custom-web ext-webauth-mode
config custom-web ext-webauth-url
config custom-web ext-webserver
config custom-web redirectUrl
config custom-web webauth-type
config custom-web weblogo
config custom-web webmessage
config custom-web webtitleshow database summary
To display the maximum number of entries in the database, use the show database summary command.
show database summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a summary of the local database configuration:
> show database summaryMaximum Database Entries......................... 2048Maximum Database Entries On Next Reboot.......... 2048Database ContentsMAC Filter Entries........................... 2Exclusion List Entries....................... 0AP Authorization List Entries................ 1Management Users............................. 1Local Network Users.......................... 1Local Users.............................. 1Guest Users.............................. 0Total..................................... 5Related Commands
show debug
To determine if the MAC address and other flag debugging is enabled or disabled, sse the show debug command.
show debug [packet]
Syntax Description
Defaults
None.
Examples
This example shows how to display if debugging is enabled:
> show debugMAC debugging............................... disabledDebug Flags Enabled:arp error enabled.bcast error enabled.This example shows how to display if debugging is enabled:
> show debugStatus........................................... disabledNumber of packets to display..................... 0Bytes/packet to display.......................... 0Packet display format............................ text2pcapDriver ACL:[1]: disabled[2]: disabled[3]: disabled[4]: disabled[5]: disabled[6]: disabledEthernet ACL:[1]: disabled[2]: disabled[3]: disabled[4]: disabled[5]: disabled[6]: disabledIP ACL:[1]: disabled[2]: disabled[3]: disabled[4]: disabled[5]: disabled[6]: disabledEoIP-Ethernet ACL:[1]: disabled[2]: disabled[3]: disabled[4]: disabled[5]: disabled[6]: disabledEoIP-IP ACL:[1]: disabled[2]: disabled[3]: disabled[4]: disabled[5]: disabled[6]: disabledLWAPP-Dot11 ACL:[1]: disabled[2]: disabled[3]: disabled[4]: disabled[5]: disabled[6]: disabledLWAPP-IP ACL:[1]: disabled[2]: disabled[3]: disabled[4]: disabled[5]: disabled[6]: disabledRelated Commands
show dhcp
To display the internal Dynamic Host Configuration Protocol (DHCP) server configuration, use the show dhcp command.
show dhcp {detailed | leases | opt-82 | proxy | stats |summary | timeout | scope}
Syntax Description
Defaults
None.
Examples
This example shows how to display the allocated DHCP leases:
> show dhcp leasesNo leases allocated.This example shows how to display the DHCP summary information:
> show dhcp summaryScope Name Enabled Address Range003 No 0.0.0.0 -> 0.0.0.0This example shows how to display the DHCP information for the scope 003:
> show dhcp 003Enabled....................................... NoLease Time.................................... 0Pool Start.................................... 0.0.0.0Pool End...................................... 0.0.0.0Network....................................... 0.0.0.0Netmask....................................... 0.0.0.0Default Routers............................... 0.0.0.0 0.0.0.0 0.0.0.0DNS Domain....................................DNS........................................... 0.0.0.0 0.0.0.0 0.0.0.0Netbios Name Servers.......................... 0.0.0.0 0.0.0.0 0.0.0.0> how dhcp detailed "scope 003"Enabled.......................................... NoLease Time....................................... 86400 (1 day )Pool Start....................................... 0.0.0.0Pool End......................................... 0.0.0.0Network.......................................... 0.0.0.0Netmask.......................................... 0.0.0.0Default Routers.................................. 0.0.0.0 0.0.0.0 0.0.0.0DNS Domain.......................................DNS.............................................. 0.0.0.0 0.0.0.0 0.0.0.0Netbios Name Servers............................. 0.0.0.0 0.0.0.0 0.0.0.0Related Commands
config dhcp
config dhcp proxy
config interface dhcp
config wlan dhcp_server
debug dhcp
debug dhcp service-port
debug disable-all
show dhcp proxyshow dtls connections
To display the Datagram Transport Layer Security (DTLS) server status, use the show dtls connections command.
show dtls connections
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the established dtls connections:
> show dtls connectionsAP Name Local Port Peer IP Peer Port Ciphersuite--------------- ------------- --------------- ------------- -----------------------1130 Capwap_Ctrl 1.100.163.210 23678 TLS_RSA _WITH_AES_128_CBC_SHA1130 Capwap_Data 1.100.163.210 23678 TLS_RSA _WITH_AES_128_CBC_SHA1240 Capwap_Ctrl 1.100.163.209 59674 TLS_RSA _WITH_AES_128_CBC_SHAshow dhcp proxy
To display the status of DHCP proxy handling, use the show dhcp proxy command.
show dhcp proxy
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the status of dhcp proxy information:
> show dhcp proxyDHCP Proxy Behavior: enabledRelated Commands
config dhcp
config dhcp proxy
config interface dhcp
config wlan dhcp_server
debug dhcp
debug dhcp service-port
debug disable-all
show dhcpshow eventlog
To display the event log, use the show eventlog command.
show eventlog
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the event log entries:
> show eventlogTimeFile Line TaskID Code d h m sEVENT> bootos.c 788 125CEBCC AAAAAAAA 0 0 0 6EVENT> bootos.c 788 125CEBCC AAAAAAAA 0 0 0 6EVENT> bootos.c 788 125C597C AAAAAAAA 0 0 0 6EVENT> bootos.c 788 125C597C AAAAAAAA 0 0 0 6EVENT> bootos.c 788 125C597C AAAAAAAA 0 0 0 6EVENT> bootos.c 788 125C597C AAAAAAAA 0 0 0 6EVENT> bootos.c 788 125C597C AAAAAAAA 0 0 0 6EVENT> bootos.c 788 125C597C AAAAAAAA 0 0 0 6EVENT> bootos.c 788 1216C36C AAAAAAAA 0 0 0 6EVENT> bootos.c 788 1216C36C AAAAAAAA 0 0 0 6EVENT> bootos.c 788 1216C36C AAAAAAAA 0 0 0 6EVENT> bootos.c 788 1216C36C AAAAAAAA 0 0 0 11show exclusionlist
To display a summary of all clients on the manual exclusion list (blacklisted) from associating with this Cisco wireless LAN controller, use the show exclusionlist command.
show exclusionlist
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Usage Guidelines
This command displays all manually excluded MAC addresses.
Examples
This example shows how to display the exclusion list> show exclusionlistMAC Address Description----------------------- --------------------------------xx:xx:xx:xx:xx:xx Disallowed ClientRelated Commands
show guest-lan
To display the configuration of a specific wired guest LAN, use the show guest-lan command.
show guest-lan guest_lan_id
Syntax Description
Defaults
None.
Usage Guidelines
To display all wired guest LANs configured on the controller, use the show guest-lan summary command.
Examples
This example shows how to display the guest LAN configuration:
> show guest-lan 2Guest LAN Identifier........................... 1Profile Name................................... guestlanNetwork Name (SSID)............................ guestlanStatus......................................... EnabledAAA Policy Override............................ DisabledNumber of Active Clients....................... 1Exclusionlist Timeout.......................... 60 secondsSession Timeout................................ InfinityInterface...................................... wiredIngress Interface.............................. wired-guestWLAN ACL....................................... unconfiguredDHCP Server.................................... 10.20.236.90DHCP Address Assignment Required............... DisabledQuality of Service............................. Silver (best effort)SecurityWeb Based Authentication................... EnabledACL........................................ UnconfiguredWeb-Passthrough............................ DisabledConditional Web Redirect................... DisabledAuto Anchor................................ DisabledMobility Anchor ListGLAN ID IP Address StatusRelated Commands
config guest-lan
config guest-lan custom-web ext-webauth-url
config guest-lan custom-web global disable
config guest-lan custom-web login_page
config guest-lan nac
config guest-lan securityshow hreap group detail
To display the details for a specific hybrid-REAP group, use the show hreap group detail command.
show hreap group detail group_name
Syntax Description
Defaults
None.
Examples
This example shows how to display the detailed information for a specific hybrid-REAP group:
> show hreap group detail 192.12.1.2Number of Ap's in Group: 100:0a:b8:3b:0b:c2 AP1200 JoinedGroup Radius Auth Servers:Primary Server Index ..................... DisabledSecondary Server Index ................... DisabledRelated Commands
config hreap group
show hreap group summaryshow hreap group summary
To display the current list of hybrid-REAP groups, use the show hreap group summary command.
show hreap group summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the current list of hybrid-REAP groups:
> show hreap group summaryHREAP Group Summary: Count 1Group Name # APsGroup 1 1Related Commands
config hreap group
show hreap group detailshow hreap office-extend
To display hybrid-REAP OfficeExtend access point information, use the show hreap office-extend command.
show hreap office-extend {summary | latency}
Syntax Description
summary
Displays a list of all OfficeExtend access points.
latency
Displays the link delay for OfficeExtend access points.
Defaults
None.
Examples
This example shows how to display information about the list of hybrid-REAP officeExtend access points:
> show hreap office-extend summarySummary of OfficeExtend APAP Name Ethernet MAC Encryption Join-Mode Join-Time------------------ ----------------- ---------- ----------- ----------AP1130 00:22:90:e3:37:70 Enabled Latency Sun Jan 4 21:46:07 2009AP1140 01:40:91:b5:31:70 Enabled Latency Sat Jan 3 19:30:25 2009This example shows how to display the hybrid-REAP officeExtend access point's link delay:
> show hreap office-extend latencySummary of OfficeExtend AP link latencyAP Name Status Current Maximum Minimum--------------------------------------------------------------------------AP1130 Enabled 15 ms 45 ms 12 msAP1140 Enabled 14 ms 179 ms 12 msRelated Commands
config hreap group
show hreap group detailshow ike
To display active Internet Key Exchange (IKE) security associations (SAs), use the show ike command.
show ike {brief | detailed} IP_or_MAC_address
Syntax Description
brief
Displays a brief summary of all active IKE SAs.
detailed
Displays a detailed summary of all active IKE SAs.
IP_or_MAC_address
IP or MAC address of active IKE SA.
Defaults
None.
Examples
This example shows how to display the active Internet Key Exchange security associations:> show ike brief 10.10.10.10show interface
To display details of the system interfaces, use the show interface command:
show interface {summary | detailed interface_name}
Syntax Description
summary
Displays a summary of the local interfaces.
detailed
Displays detailed interface information.
interface_name
Interface name for detailed display.
Defaults
None.
Usage Guidelines
The interface name of the wired guest LAN in the following example is management and its VLAN ID is 149.
Examples
This example shows how to display a summary of the local interfaces:
> show interface summaryInterface Name Port Vlan Id IP Address Type Ap Mgr Guest------------------- ---- --------- ---------------- ------ ------ ------ap-manager 1 untagged xxx.xxx.xxx.xxx Static Yes Nomanagement 1 untagged xxx.xxx.xxx.xxx Static No Noservice-port N/A N/A xxx.xxx.xxx.xxx Static No Novirtual N/A N/A xxx.xxx.xxx.xxx Static No NoThis example shows how to display the detailed interface information:
> show interface detailed managementInterface Name................................... managementMAC Address...................................... 00:0b:85:32:ab:60IP Address....................................... 1.100.49.30IP Netmask....................................... 255.255.255.0IP Gateway....................................... 1.100.49.1VLAN............................................. 149Active Physical Port............................. 1Primary Physical Port............................ 1Backup Physical Port............................. UnconfiguredPrimary DHCP Server.............................. 1.100.2.15Secondary DHCP Server............................ UnconfiguredACL.............................................. UnconfiguredAP Manager....................................... No
Note
show invalid-config
To see any ignored commands or invalid configuration values in an edited configuration file, use the show invalid-config command.
show invalid-config
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Usage Guidelines
You can execute this command only before the clear config or save config command.
Examples
This example shows how to display a list of any ignored commands or invalid configuration values in a configuration file:
> show invalid-configconfig wlan peer-blocking drop 3config wlan dhcp_server 3 192.168.0.44 requiredshow inventory
To display a physical inventory of the Cisco wireless LAN controller, use the show inventory command.
show inventory
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Usage Guidelines
Some wireless LAN controllers may have no crypto accelerator (VPN termination module) or power supplies listed because they have no provisions for VPN termination modules or power supplies.
Examples
This example shows how to display a physical inventory of the controller:
> show inventorySwitch Description............................... Cisco ControllerMachine Model.................................... WLC4404-100Serial Number.................................... FLS0923003BBurned-in MAC Address............................ 00:0B:85:32:AB:60Crypto Accelerator 1............................. AbsentCrypto Accelerator 2............................. AbsentPower Supply 1................................... AbsentPower Supply 2................................... Present, OKRelated Commands
show IPsec
To display active Internet Protocol Security (IPsec) security associations (SAs), use the show IPsec commands.
show IPsec {brief | detailed} IP_or_MAC_address
Syntax Description
brief
Displays a brief summary of active IPsec SAs.
detailed
Displays a detailed summary of active IPsec SAs.
IP_or_MAC_address
IP address or MAC address of a device.
Defaults
None.
Examples
This example shows how to display brief information about the active Internet Protocol Security (IPsec) security associations (SAs):
> show IPsec brief 10.10.10.10Related Commands
config radius acct IPsec authentication
config radius acct IPsec disable
config radius acct IPsec enable
config radius acct IPsec encryption
config radius acct IPsec ike
config radius auth IPsec authentication
config radius auth IPsec disable
config radius auth IPsec encryption
config radius auth IPsec ike
config trapflags IPsec
config wlan security IPsec disable
config wlan security IPsec enable
config wlan security IPsec authentication
config wlan security IPsec encryption
config wlan security IPsec config
config wlan security IPsec ike authentication
config wlan security IPsec ike dh-group
config wlan security IPsec ike lifetime
config wlan security IPsec ike phase1
config wlan security IPsec ike contivityshow known ap
To display known Cisco lightweight access point information, use the show known ap command.
show known ap {summary | detailed MAC}
Syntax Description
summary
Displays a list of all known access points.
detailed
Provides detailed information for all known access points.
MAC
MAC address of the known AP.
Defaults
None.
Examples
This example shows how to display a summary of all known access points:
> show known ap summaryMAC Address State # APs # Clients Last Heard----------- ----------- ----- -------- -----------------Related Commands
show l2tp
To display Layer 2 Tunneling Protocol (L2TP) sessions, use the show l2tp command.
show l2tp {summary | ip_address}
Syntax Description
Defaults
None.
Examples
This example shows how to display a summary of all L2TP sessions:
> show l2tp summaryLAC_IPaddr LTid LSid RTid RSid ATid ASid State---------- ---- ---- ---- ---- ---- ---- -----show lag summary
To display the current link aggregation (LAG) status, use the show lag summary command.
show lag summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the current status of the LAG configuration:
> show lag summaryLAG EnabledRelated Commands
show ldap
To display the Lightweight Directory Access Protocol (LDAP) server information for a particular LDAP server, use the show ldap command.
show ldap index
Syntax Description
Defaults
None.
Examples
This example shows how to display the detailed LDAP server information:
> show ldap 1Server Index..................................... 1Address.......................................... 2.3.1.4Port............................................. 389Enabled.......................................... YesUser DN.......................................... name1User Attribute................................... attr1User Type........................................ username1Retransmit Timeout............................... 3 secondsBind Method ..................................... AnonymousRelated Commands
config ldap
config ldap add
config ldap simple-bind
show ldap statistics
show ldap summaryshow ldap statistics
To display all Lightweight Directory Access Protocol (LDAP) server information, use the show ldap statistics command.
show ldap statistics
Syntax Description
This command has no arguments or keywords:
Examples
This example shows how to display the LDAP server statistics:
> show ldap statisticsServer Index..................................... 1Server statistics:Initialized OK................................. 0Initialization failed.......................... 0Initialization retries......................... 0Closed OK...................................... 0Request statistics:Received....................................... 0Sent........................................... 0OK............................................. 0Success........................................ 0Authentication failed.......................... 0Server not found............................... 0No received attributes......................... 0No passed username............................. 0Not connected to server........................ 0Internal error................................. 0Retries........................................ 0Server Index..................................... 2...Related Commands
config ldap
config ldap add
config ldap simple-bind
show ldap
show ldap summaryshow ldap summary
To display the current Lightweight Directory Access Protocol (LDAP) server status, use the show ldap summary command.
show ldap summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a summary of configured LDAP servers:
> show ldap summaryIdx Server Address Port Enabled
--- --------------- ---- -------
1 2.3.1.4 389 Yes
2 10.10.20.22 389 Yes
Related Commands
config ldap
config ldap add
config ldap simple-bind
show ldap
show ldap statisticsshow license agent
To display the license agent counter and session information on the Cisco 5500 Series Controller, use the show license agent command.
show license agent {counters | sessions}
Syntax Description
Defaults
None.
Examples
This example shows how to display the license agent counters information:
> show license agent countersLicense Agent CountersRequest Messages Received:0: Messages with Errors:0Request Operations Received:0: Operations with Errors:0Notification Messages Sent:0: Transmission Errors:0: Soap Errors:0This example shows how to display the license agent sessions information:
> show license agent sessionsLicense Agent Sessions: 0 open, maximum is 9Related Commands
config license agent
clear license agent
show license all
show license detail
show license feature
show license image-level
show license summaryshow license all
To display information for all licenses on the Cisco 5500 Series Controller, use the show license all command.
show license all
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display all the licenses:
> show license allLicense Store: Primary License StorageStoreIndex: 0 Feature: wplus-ap-count Version: 1.0License Type: PermanentLicense State: InactiveLicense Count: 12/0/0License Priority: MediumStoreIndex: 1 Feature: base Version: 1.0License Type: PermanentLicense State: Active, Not in UseLicense Count: Non-CountedLicense Priority: MediumStoreIndex: 2 Feature: wplus Version: 1.0License Type: PermanentLicense State: Active, In UseLicense Count: Non-CountedLicense Priority: MediumLicense Store: Evaluation License StorageStoreIndex: 0 Feature: wplus Version: 1.0License Type: EvaluationLicense State: InactiveEvaluation total period: 8 weeks 4 daysEvaluation period left: 6 weeks 6 daysLicense Count: Non-CountedLicense Priority: LowStoreIndex: 1 Feature: wplus-ap-count Version: 1.0License Type: EvaluationLicense State: Active, In UseEvaluation total period: 8 weeks 4 daysEvaluation period left: 2 weeks 3 daysExpiry date: Thu Jun 25 18:09:43 2009License Count: 250/250/0License Priority: HighStoreIndex: 2 Feature: base Version: 1.0License Type: EvaluationLicense State: InactiveEvaluation total period: 8 weeks 4 daysEvaluation period left: 8 weeks 4 daysLicense Count: Non-CountedLicense Priority: LowStoreIndex: 3 Feature: base-ap-count Version: 1.0License Type: EvaluationLicense State: Active, Not in Use, EULA acceptedEvaluation total period: 8 weeks 4 daysEvaluation period left: 8 weeks 3 daysLicense Count: 250/0/0License Priority: LowRelated Commands
license install
license modify priority
show license agent
show license detail
show license feature
show license image-level
show license summaryshow license capacity
To display the maximum number of access points allowed for this license on the Cisco 5500 Series Controller, the number of access points currently joined to the controller, and the number of access points that can still join the controller, use the show license capacity command.
show license capacity
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the license capacity:
> show license capacityLicensed Feature Max Count Current Count Remaining Count-----------------------------------------------------------------------AP Count 250 47 203Related Commands
license install
license modify priority
show license agent
show license all
show license detail
show license feature
show license image-level
show license summaryshow license detail
To display details of a specific license on the Cisco 5500 Series Controller, use the show license detail command.
show license detail license_name
Syntax Description
Defaults
None.
Examples
This example shows how to display the license details:
> show license detail wplusFeature: wplus Period left: Life timeIndex: 1 Feature: wplus Version: 1.0License Type: PermanentLicense State: Active, In UseLicense Count: Non-CountedLicense Priority: MediumStore Index: 2Store Name: Primary License StorageIndex: 2 Feature: wplus Version: 1.0License Type: EvaluationLicense State: InactiveEvaluation total period: 8 weeks 4 daysEvaluation period left: 6 weeks 6 daysLicense Count: Non-CountedLicense Priority: LowStore Index: 0Related Commands
license install
license modify priority
show license agent
show license all
show license feature
show license image-level
show license summaryshow license expiring
To display details of expiring licenses on the Cisco 5500 Series Controller, use the show license expiring command.
show license expiring
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the details of the expiring licenses:
> show license expiringStoreIndex: 0 Feature: wplus Version: 1.0License Type: EvaluationLicense State: InactiveEvaluation total period: 8 weeks 4 daysEvaluation period left: 6 weeks 6 daysLicense Count: Non-CountedLicense Priority: LowStoreIndex: 1 Feature: wplus-ap-count Version: 1.0License Type: EvaluationLicense State: Active, In UseEvaluation total period: 8 weeks 4 daysEvaluation period left: 2 weeks 3 daysExpiry date: Thu Jun 25 18:09:43 2009License Count: 250/250/0License Priority: HighStoreIndex: 2 Feature: base Version: 1.0License Type: EvaluationLicense State: InactiveEvaluation total period: 8 weeks 4 daysEvaluation period left: 8 weeks 4 daysLicense Count: Non-CountedLicense Priority: LowStoreIndex: 3 Feature: base-ap-count Version: 1.0License Type: EvaluationLicense State: Active, Not in Use, EULA acceptedEvaluation total period: 8 weeks 4 daysEvaluation period left: 8 weeks 3 daysLicense Count: 250/0/0License Priority: LowRelated Commands
license install
license modify priority
show license all
show license detail
show license evaluation
show license in-use
show license summaryshow license evaluation
To display details of evaluation licenses on the Cisco 5500 Series Controller, use the show license evaluation command.
show license evaluation
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the details of the evaluation licenses:
> show license evaluationStoreIndex: 0 Feature: wplus Version: 1.0License Type: EvaluationLicense State: InactiveEvaluation total period: 8 weeks 4 daysEvaluation period left: 6 weeks 6 daysLicense Count: Non-CountedLicense Priority: LowStoreIndex: 1 Feature: wplus-ap-count Version: 1.0License Type: EvaluationLicense State: Active, In UseEvaluation total period: 8 weeks 4 daysEvaluation period left: 2 weeks 3 daysExpiry date: Thu Jun 25 18:09:43 2009License Count: 250/250/0License Priority: HighStoreIndex: 2 Feature: base Version: 1.0License Type: EvaluationLicense State: InactiveEvaluation total period: 8 weeks 4 daysEvaluation period left: 8 weeks 4 daysLicense Count: Non-CountedLicense Priority: LowStoreIndex: 3 Feature: base-ap-count Version: 1.0License Type: EvaluationLicense State: Active, Not in Use, EULA acceptedEvaluation total period: 8 weeks 4 daysEvaluation period left: 8 weeks 3 daysLicense Count: 250/0/0License Priority: LowRelated Commands
license install
license modify priority
show license all
show license detail
show license expiring
show license in-use
show license summaryshow license feature
To display a summary of license-enabled features on the Cisco 5500 Series Controller, use the show license feature command.
show license feature
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the license-enabled features:
> show license featureFeature name Enforcement Evaluation Clear Allowed Enabledwplus yes yes yes yeswplus-ap-count yes yes yes yesbase no yes yes nobase-ap-count yes yes yes noRelated Commands
license install
license modify priority
show license all
show license detail
show license expiring
show license evaluation
show license image-level
show license in-use
show license summaryshow license file
To display a summary of license-enabled features on the Cisco 5500 Series Controller, use the show license file command.
show license file
Syntax Description
Defaults
None.
Examples
This example shows how to display the license files:
> show license fileLicense Store: Primary License StorageStore Index: 0License: 11 wplus-ap-count 1.0 LONG NORMAL STANDALONE EXCL 12_KEYS INFINITE_KEYS NEVER NEVER NiL SLM_CODE CL_ND_LCK NiL *1AR5NS7M5AD8PPU400NiL NiL NiL 5_MINS <UDI><PID>AIR-CT5508-K9</PID><SN>RFD000P2D27</SN></UDI> Pe0L7tv8KDUqo:zlPe423S5wasgM8G,tTs0i,7zLyA3VfxhnIe5aJam63lR5l8JM3DPkr4O2DI43iLlKn7jomo3RFl1LjMRqLkKhiLJ2tOyuftQSq2bCAO6nR3wIb38xKi3t$<WLC>AQEBIQAB//++mCzRUbOhw28vz0czAY0iAm7ocDLUMb9ER0+BD3w2PhNEYwsBN/T3xXBqJqfC+oKRqwInXo3s+nsLU7rOtdOxoIxYZAo3LYmUJ+MFzsqlhKoJVlPyEvQ8H21MNUjVbhoN0gyIWsyiJaM8AQIkVBQFzhr10GYolVzdzfJfEPQIx6tZ++/Vtc/q3SF/5Ko8XCY=</WLC>Comment:Hash: iOGjuLlXgLhcTB113ohIzxVioHA=. . .Related Commands
license install
show license all
show license detail
show license expiring
show license feature
show license image-level
show license in-use
show license summaryshow license handle
To display the license handles on the Cisco 5500 Series Controller, use the show license handle command.
show license handle
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the license handles:
> show license handleFeature: wplus , Handle Count: 1Units: 01( 0), ID: 0x5e000001, NotifyPC: 0x1001e8f4 LS-Handle (0x00000001),Units: ( 1)Registered clients: 1Context 0x1051b610, epID 0x10029378Feature: base , Handle Count: 0Registered clients: 1Context 0x1053ace0, epID 0x10029378Feature: wplus-ap-count , Handle Count: 1Units: 250( 0), ID: 0xd4000002, NotifyPC: 0x1001e8f4 LS-Handle (0x00000002), Units: (250)Registered clients: NoneFeature: base-ap-count , Handle Count: 0Registered clients: NoneGlobal Registered clients: 2Context 0x10546270, epID 0x100294ccContext 0x1053bae8, epID 0x100294ccRelated Commands
license install
show license all
show license detail
show license expiring
show license feature
show license image-level
show license in-use
show license summaryshow license image-level
To display the license image level that is in use on the Cisco 5500 Series Controller, use the show license image-level command.
show license image-level
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the image level license settings:
> show license image-levelModule name Image level Priority Configured Valid licensewnbu wplus 1 YES wplusbase 2 NONOTE: wplus includes two additional features: Office Extend AP, Mesh AP.Related Commands
license install
license modify priority
show license all
show license detail
show license expiring
show license feature
show license in-use
show license summaryshow license in-use
To display the licenses that are in use on the Cisco 5500 Series Controller, use the show license in-use command.
show license in-use
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the licenses that are in use:
> show license in-useStoreIndex: 2 Feature: wplus Version: 1.0License Type: PermanentLicense State: Active, In UseLicense Count: Non-CountedLicense Priority: MediumStoreIndex: 1 Feature: wplus-ap-count Version: 1.0License Type: EvaluationLicense State: Active, In UseEvaluation total period: 8 weeks 4 daysEvaluation period left: 2 weeks 3 daysExpiry date: Thu Jun 25 18:09:43 2009License Count: 250/250/0License Priority: HighRelated Commands
license install
license modify priority
show license all
show license detail
show license evaluation
show license expiring
show license feature
show license image-level
show license permanent
show license summaryshow license permanent
To display the permanent licenses on the Cisco 5500 Series Controller, use the show license permanent command.
show license permanent
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the permanent license's information:
> show license permanentStoreIndex: 0 Feature: wplus-ap-count Version: 1.0License Type: PermanentLicense State: InactiveLicense Count: 12/0/0License Priority: MediumStoreIndex: 1 Feature: base Version: 1.0License Type: PermanentLicense State: Active, Not in UseLicense Count: Non-CountedLicense Priority: MediumStoreIndex: 2 Feature: wplus Version: 1.0License Type: PermanentLicense State: Active, In UseLicense Count: Non-CountedLicense Priority: MediumRelated Commands
license install
license modify priority
show license all
show license detail
show license evaluation
show license expiring
show license feature
show license image-level
show license in-use
show license summaryshow license status
To display the license status on the Cisco 5500 Series Controller, use the show license status command.
show license status
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the license status:
> show license statusLicense Type Supportedpermanent Non-expiring node locked licenseextension Expiring node locked licenseevaluation Expiring non node locked licenseLicense Operation Supportedinstall Install licenseclear Clear licenseannotate Comment licensesave Save licenserevoke Revoke licenseDevice statusDevice Credential type: DEVICEDevice Credential Verification: PASSRehost Type: DC_OR_ICRelated Commands
license install
license modify priority
show license all
show license detail
show license evaluation
show license expiring
show license feature
show license image-level
show license permanent
show license summaryshow license statistics
To display license statistics on the Cisco 5500 Series Controller, use the show license statistics command.
show license statistics
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the license statistics:
> show license statisticsAdministrative statisticsInstall success count: 0Install failure count: 0Install duplicate count: 0Comment add count: 0Comment delete count: 0Clear count: 0Save count: 0Save cred count: 0Client statusRequest success count 2Request failure count 0Release count 0Global Notify count 0Related Commands
license install
license modify priority
show license all
show license detail
show license evaluation
show license expiring
show license feature
show license image-level
show license permanent
show license summaryshow license summary
To display a brief summary of all licenses on the Cisco 5500 Series Controller, use the show license summary command.
show license summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a brief summary of all licenses:
> show license summaryIndex 1 Feature: wplusPeriod left: Life timeLicense Type: PermanentLicense State: Active, In UseLicense Count: Non-CountedLicense Priority: MediumIndex 2 Feature: wplus-ap-countPeriod left: 2 weeks 3 daysLicense Type: EvaluationLicense State: Active, In UseLicense Count: 250/250/0License Priority: HighIndex 3 Feature: basePeriod left: Life timeLicense Type: PermanentLicense State: Active, Not in UseLicense Count: Non-CountedLicense Priority: MediumIndex 4 Feature: base-ap-countPeriod left: 8 weeks 3 daysLicense Type: EvaluationLicense State: Active, Not in Use, EULA acceptedLicense Count: 250/0/0License Priority: LowRelated Commands
license install
license modify priority
show license all
show license detail
show license evaluation
show license expiring
show license feature
show license image-level
show license permanent
show license summaryshow license udi
To display unique device identifier (UDI) values for licenses on the Cisco 5500 Series Controller, use the show license udi command.
show license udi
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the UDI values for licenses:
> show license udiDevice# PID SN UDI-------------------------------------------------------------------------------------*0 AIR-CT5508-K9 RFD000P2D27 AIR-CT5508-K9:RFD000P2D27Related Commands
license install
license modify priority
show license all
show license detail
show license evaluation
show license expiring
show license feature
show license image-level
show license permanent
show license summaryshow load-balancing
To display the status of the load-balancing feature, use the show load-balancing command.
show load-balancing
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the load-balancing status:
> show load-balancingAggressive Load Balancing........................ EnabledAggressive Load Balancing Window................. 0 clientsAggressive Load Balancing Denial Count........... 3StatisticsTotal Denied Count............................... 10 clientsTotal Denial Sent................................ 20 messagesExceeded Denial Max Limit Count.................. 0 timesNone 5G Candidate Count.......................... 0 timesNone 2.4G Candidate Count..................... 0 timesRelated Commands
show local-auth certificates
To display local authentication certificate information, use the show local-auth certificates command:
show local-auth certificates
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the authentication certificate information stored locally:
> show local-auth certificatesCertificates available for Local EAP authentication: Certificate issuer .............................. vendorCA certificate:Subject: C=AU, ST=NSW, L=Sydney, O=Cisco Systems OU=WNBU Sydney, CN=wnbu-syd-acs-a.cisco.com Issuer: C=AU, ST=NSW, L=Sydney, O=Cisco Systems OU=WNBU Sydney, CN=wnbu-syd-acs-a.cisco.com Valid: 2005 Jun 15th, 04:53:49 GMT to 2008 Jun 15th, 05:03:34 GMT Device certificate: Subject: MAILTO=test@test.net, C=AU, ST=NSW, L=Sydney O=Cisco Systems, OU=WNBU Sydney, CN=concannon Issuer: C=AU, ST=NSW, L=Sydney, O=Cisco Systems OU=WNBU Sydney, CN=wnbu-syd-acs-a.cisco.com Valid: 2006 Aug 9th, 05:14:16 GMT to 2007 Aug 9th, 05:24:16 GMTCertificate issuer .............................. ciscoCA certificate:Subject: C=US, ST=California, L=San Jose, O=airespace Inc OU=none, CN=ca, MAILTO=support@airespace.com Issuer: C=US, ST=California, L=San Jose, O=airespace Inc OU=none, CN=ca, MAILTO=support@airespace.com Valid: 2003 Feb 12th, 23:38:55 GMT to 2012 Nov 11th, 23:38:55 GMT Device certificate: Subject: C=US, ST=California, L=San Jose, O=airespace Inc CN=000b85335340, MAILTO=support@airespace.com Issuer: C=US, ST=California, L=San Jose, O=airespace Inc OU=none, CN=ca, MAILTO=support@airespace.com Valid: 2005 Feb 22nd, 10:52:58 GMT to 2014 Nov 22nd, 10:52:58 GMTCertificate issuer .............................. legacyCA certificate:Subject: C=US, ST=California, L=San Jose, O=airespace Inc OU=none, CN=ca, MAILTO=support@airespace.com Issuer: C=US, ST=California, L=San Jose, O=airespace Inc OU=none, CN=ca, MAILTO=support@airespace.com Valid: 2003 Feb 12th, 23:38:55 GMT to 2012 Nov 11th, 23:38:55 GMT Device certificate: Subject: C=US, ST=California, L=San Jose, O=airespace Inc CN=000b85335340, MAILTO=support@airespace.com Issuer: C=US, ST=California, L=San Jose, O=airespace Inc OU=none, CN=ca, MAILTO=support@airespace.com Valid: 2005 Feb 22nd, 10:52:58 GMT to 2014 Nov 22nd, 10:52:58 GMTRelated Commands
clear stats local-auth
config local-auth active-timeout
config local-auth eap-profile
config local-auth method fast
config local-auth user-credentials
debug aaa local-auth
show local-auth config
show local-auth statisticsshow local-auth config
To display local authentication configuration information, use the show local-auth config command.
show local-auth config
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the local authentication configuration information:
> show local-auth configUser credentials database search order:Primary ................................... Local DBConfigured EAP profiles:Name ...................................... fast-testCertificate issuer .................... defaultEnabled methods ....................... fastConfigured on WLANs ................... 2EAP Method configuration:EAP-TLS:Certificate issuer .................... defaultPeer verification options:Check against CA certificates ..... EnabledVerify certificate CN identity .... DisabledCheck certificate date validity ... EnabledEAP-FAST:TTL for the PAC ....................... 3 600Initial client message ................ <none>Local certificate required ............ NoClient certificate required ........... NoVendor certificate required ........... NoAnonymous provision allowed ........... YesAuthenticator ID ...................... 7b7fffffff0000000000000000000000Authority Information ................. TestEAP Profile.................................... tls-profEnabled methods for this profile .......... tlsActive on WLANs ........................... 1 3EAP Method configuration:EAP-TLS:Certificate issuer used ............... ciscoPeer verification options:Check against CA certificates ..... disabledVerify certificate CN identity .... disabledCheck certificate date validity ... disabledRelated Commands
clear stats local-auth
config local-auth active-timeout
config local-auth eap-profile
config local-auth method fast
config local-auth user-credentials
debug aaa local-auth
show local-auth certificates
show local-auth statisticsshow local-auth statistics
To display local Extensible Authentication Protocol (EAP) authentication statistics, use the show local-auth statistics command:
show local-auth statistics
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the local authentication certificate statistics:
> show local-auth statisticsLocal EAP authentication DB statistics:Requests received ............................... 14Responses returned .............................. 14Requests dropped (no EAP AVP) ................... 0Requests dropped (other reasons) ................ 0Authentication timeouts ......................... 0Authentication statistics:Method Success Fail------------------------------------Unknown 0 0LEAP 0 0EAP-FAST 2 0EAP-TLS 0 0PEAP 0 0Local EAP credential request statistics:Requests sent to LDAP DB ........................ 0Requests sent to File DB ........................ 2Requests failed (unable to send) ................ 0Authentication results received:Success ....................................... 2Fail .......................................... 0Certificate operations:Local device certificate load failures .......... 0Total peer certificates checked ................. 0Failures:CA issuer check ............................... 0CN name not equal to identity ................. 0Dates not valid or expired .................... 0Related Commands
clear stats local-auth
config local-auth active-timeout
config local-auth eap-profile
config local-auth method fast
config local-auth user-credentials
debug aaa local-auth
show local-auth certificates
show local-auth configshow location
To display location system information, use the show location command.
show location [detail mac_address | summary]
Syntax Description
detail
(Optional) Displays detailed location information.
mac_address
MAC address of a client.
summary
(Optional) Displays summary location information.
Defaults
None.
Examples
This example shows how to display the location summary information:
> show location summaryLocation SummaryAlgorithm used: AverageClientRSSI expiry timeout: 5 secHalf life: 0 secNotify Threshold: 0 dbCalibrating ClientRSSI expiry timeout: 5 secHalf life: 0 secRogue APRSSI expiry timeout: 5 secHalf life: 0 secNotify Threshold: 0 dbRFID TagRSSI expiry timeout: 5 secHalf life: 0 secNotify Threshold: 0 dbRelated Commands
clear location rfid
clear location statistics rfid
config location
show location statistics rfidshow location statistics rfid
To see any radio frequency identification (RFID)-related errors, use the show location statistics rfid command.
show location statistics rfid
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the detailed location RFID statistics:
> show location statistics rfidRFID StatisticsDatabase Full : 0 Failed Delete: 0Null Bufhandle: 0 Bad Packet: 0Bad LWAPP Data: 0 Bad LWAPP Encap: 0Off Channel: 0 Bad CCX Version: 0Bad AP Info : 0Above Max RSSI: 0 Below Max RSSI: 0Invalid RSSI: 0 Add RSSI Failed: 0Oldest Expired RSSI: 0 Smallest Overwrite: 0Related Commands
clear location rfid
clear location statistics rfid
config location
show locationshow logging
To display the syslog facility logging parameters and buffer contents, use the show logging command.
show logging
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the current settings and buffer content details:
> show loggingLogging to buffer :- Logging of system messages to buffer :- Logging filter level.......................... errors- Number of system messages logged.............. 67227- Number of system messages dropped............. 21136- Logging of debug messages to buffer ........... Disabled- Number of debug messages logged............... 0- Number of debug messages dropped.............. 0Logging to console :- Logging of system messages to console :- Logging filter level.......................... errors- Number of system messages logged.............. 0- Number of system messages dropped............. 88363- Logging of debug messages to console .......... Enabled- Number of debug messages logged............... 0- Number of debug messages dropped.............. 0Logging to syslog :- Syslog facility................................ local0- Logging of system messages to syslog :- Logging filter level.......................... errors- Number of system messages logged.............. 67227--More-- or (q)uit- Number of system messages dropped............. 21136- Logging of debug messages to syslog ........... Disabled- Number of debug messages logged............... 0- Number of debug messages dropped.............. 0- Number of remote syslog hosts.................. 0- Host 0....................................... Not Configured- Host 1....................................... Not Configured- Host 2....................................... Not ConfiguredLogging of traceback............................. DisabledLogging of process information................... DisabledLogging of source file informational............. EnabledTimestamping of messages.........................- Timestamping of system messages................ Enabled- Timestamp format.............................. Date and Time- Timestamping of debug messages................. Enabled- Timestamp format.............................. Date and TimeLogging buffer (67227 logged, 21136 dropped)*Apr 03 09:48:01.728: %MM-3-INVALID_PKT_RECVD: mm_listen.c:5508 Received an invalidpacket from 1.100.163.51. Source member:0.0.0.0. source member unknown.*Apr 03 09:47:34.194: %LWAPP-3-DECODE_ERR: spam_lrad.c:1271 Error decoding discoveryrequest from AP 00:13:5f:0e:d4:20*Apr 03 09:47:34.194: %LWAPP-3-DISC_OTAP_ERR: spam_lrad.c:5554 Ignoring OTAP discoveryrequest from AP 00:13:5f:0e:d4:20, OTAP is disabledPrevious message occurred 2 times.Related Commands
config logging syslog host
config logging syslog facility
config logging syslog levelshow loginsession
To display the existing sessions, use the show loginsession command.
show loginsession
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the current session details:
> show loginsessionID username Connection From Idle Time Session Time-- --------------- --------------- ------------ ------------00 admin EIA-232 00:00:00 00:19:04Related Commands
show macfilter
To display the MAC filter parameters, use the show macfilter command.
show macfilter {summary | detail MAC}
Syntax Description
summary
Displays a summary of all MAC filter entries.
detail MAC
Detailed display of a MAC filter entry.
Defaults
None.
Usage Guidelines
The MAC delimiter (none, colon, or hyphen) for MAC addresses sent to RADIUS servers is displayed. The MAC filter table lists the clients that are always allowed to associate with a wireless LAN.
Examples
This example shows how to display the detailed display of a MAC filter entry:
> show macfilter detail xx:xx:xx:xx:xx:xxMAC Address...................................... xx:xx:xx:xx:xx:xxWLAN Identifier.................................. AnyInterface Name................................... managementDescription...................................... RAPThis example shows how to display a summary of hte MAC filter parameters:
> show macfilter summaryMAC Filter RADIUS Compatibility mode............. Cisco ACSMAC Filter Delimiter............................. NoneLocal Mac Filter TableMAC Address WLAN Id Description----------------------- -------------- --------------------------------xx:xx:xx:xx:xx:xx Any RAPxx:xx:xx:xx:xx:xx Any PAP2 (2nd hop)xx:xx:xx:xx:xx:xx Any PAP1 (1st hop)Related Commands
config macfilter
config macfilter description
config macfilter interfac
config macfilter ip-address
config macfilter mac-delimiter
config macfilter radius-compat
config macfilter wlan-idshow memory monitor
To display a summary of memory analysis settings and any discovered memory issues, enter this command:
show memory monitor [detail]
Syntax Description
Defaults
None.
Usage Guidelines
Be careful when changing the defaults for the config memory monitor command unless you know what you are doing, you have detected a problem, or you are collecting troubleshooting information.
Examples
This example shows how to display a summary of memory monitoring settings and a summary of test results:
> show memory monitorMemory Leak Monitor Status:low_threshold(10000), high_threshold(30000), current status(disabled)-------------------------------------------Memory Error Monitor Status:Crash-on-error flag currently set to (disabled)No memory error detected.This example shows how to display the monitor test results:
> show memory monitor detailMemory error detected. Details:------------------------------------------------- Corruption detected at pmalloc entry address: (0x179a7ec0)- Corrupt entry:headerMagic(0xdeadf00d),trailer(0xabcd),poison(0xreadceef),entrysize(128),bytes(100),thread(Unknown task name,task id = (332096592)),file(pmalloc.c),line(1736),time(1027)Previous 1K memory dump from error location.------------------------------------------------(179a7ac0): 00000000 00000000 00000000 ceeff00d readf00d 00000080 00000000 00000000(179a7ae0): 17958b20 00000000 1175608c 00000078 00000000 readceef 179a7afc 00000001(179a7b00): 00000003 00000006 00000001 00000004 00000001 00000009 00000009 0000020d(179a7b20): 00000001 00000002 00000002 00000001 00000004 00000000 00000000 5d7b9aba(179a7b40): cbddf004 192f465e 7791acc8 e5032242 5365788c a1b7cee6 00000000 00000000(179a7b60): 00000000 00000000 00000000 00000000 00000000 ceeff00d readf00d 00000080(179a7b80): 00000000 00000000 17958dc0 00000000 1175608c 00000078 00000000 readceef(179a7ba0): 179a7ba4 00000001 00000003 00000006 00000001 00000004 00000001 00003763(179a7c00): 1722246c 1722246c 00000000 00000000 00000000 00000000 00000000 ceeff00d(179a7c20): readf00d 00000080 00000000 00000000 179a7b78 00000000 1175608c 00000078...Related Commands
config memory monitor errors
config memory monitor leaks
debug memoryshow reset
To display the scheduled system reset parameters, use the show reset command.
show reset
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the scheduled system reset parameters:
> show resetSystem reset is scheduled for Mar 27 01 :01 :01 2010Current local time and date is Mar 24 02:57:44 2010A trap will be generated 10 minutes before each scheduled system reset.Use `reset system cancel' to cancel the reset.Configuration will be saved before the system reset.Related Commands
reset system at
reset system in
reset system cancel
reset system notify-timeShow media-stream commands
Use the show media-stream commands to display the multicast-direct configuration state.
show media-stream group detail
To display the details for a specific media-stream group, use the show media-stream group detail command.
show media-stream group detail media-stream_name
Syntax Description
Defaults
None.
Examples
This example shows how to display media-stream group configuration details:
> show media-stream group detail abcMedia Stream Name................................ abcStart IP Address................................. 227.8.8.8End IP Address................................... 227.9.9.9RRC ParametersAvg Packet Size(Bytes).......................... 1200Expected Bandwidth(Kbps)........................ 300Policy.......................................... AdmitRRC re-evaluation............................... periodicQoS............................................. VideoStatus.......................................... Multicast-directUsage Priority.................................. 5Violation....................................... dropRelated Commands
show media-stream group summary
show media-stream group summary
To display the summary of the media stream and client information, use the show media-stream group summary command.
show media-stream group summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a summary of the media-stream group:
> show media-stream group summaryStream Name Start IP End IP Operation Status------------- -------------- -------------- ----------------abc 227.8.8.8 227.9.9.9 Multicast-directRelated Commands
Show Mesh Commands
To display settings for outdoor and indoor mesh access points, use the show mesh commands.
show mesh ap
To display settings for mesh access points, use the show mesh commands.
show mesh ap {summary | tree}
Syntax Description
Defaults
None.
Examples
This example shows how to display a summary format:
> show mesh ap summaryAP Name AP Model BVI MAC CERT MAC Hop Bridge Group Name------------------ ------------------- ----------------- ------------------ ----- --SB_RAP1 AIR-LAP1522AG-A-K9 00:1d:71:0e:d0:00 00:1d:71:0e:d0:00 0 sboxSB_MAP1 AIR-LAP1522AG-A-K9 00:1d:71:0e:85:00 00:1d:71:0e:85:00 1 sboxSB_MAP2 AIR-LAP1522AG-A-K9 00:1b:d4:a7:8b:00 00:1b:d4:a7:8b:00 2 sboxSB_MAP3 AIR-LAP1522AG-A-K9 00:1d:71:0d:ee:00 00:1d:71:0d:ee:00 3 sboxNumber of Mesh APs............................... 4Number of RAPs................................... 1Number of MAPs................................... 3This example shows how to display settings in a hierarchical (tree) format:
> show mesh ap tree=======================================================|| AP Name [Hop Counter, Link SNR, Bridge Group Name] ||=======================================================[Sector 1]----------SB_RAP1[0,0,sbox]|-SB_MAP1[1,32,sbox]|-SB_MAP2[2,27,sbox]|-SB_MAP3[3,30,sbox]----------------------------------------------------Number of Mesh APs............................... 4Number of RAPs................................... 1Number of MAPs................................... 3----------------------------------------------------Related Commands
config mesh alarm
config mesh astools
config mesh background-scanning
config mesh battery-stateshow mesh astools stats
To display anti-stranding statistics for outdoor mesh access points, use the show mesh astools stats command.
show mesh astools stats [cisco_ap]
Syntax Description
Defaults
None.
Examples
This example shows how to display anti-stranding statistics on all outdoor mesh access points:
> show mesh astools statsTotal No of Aps stranded : 0This example shows how to display anti-stranding statistics for access point sb_map1:
> show mesh astools stats sb_map1Total No of Aps stranded : 0Related Commands
config mesh astools
show mesh config
show mesh statsshow mesh background-scanning
To display whether or not the background-scanning feature is enabled on a mesh network, use the show mesh background-scanning command.
show mesh background-scanning
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Usage Guidelines
The secondary backhaul access feature is not supported by Cisco 1520 and 1524 indoor mesh access points in the 5.2 release.
Examples
This example shows how to display the state of the background-scanning feature:
> show mesh background-scanningBackground Scanning State: enabledRelated Commands
config mesh background-scanning
show mesh config
show mesh statsshow mesh backhaul rate-adapt
To display whether or not clients on a mesh network have access to the backhaul channel, and at what level of service, use the show mesh backhaul rate-adapt command.
show mesh backhaul rate-adapt {all | bronze | silver | gold | platinum}
Syntax Description
Defaults
None.
Examples
This example shows how to display the state of the backhaul rate-adaption feature:
> show mesh backhaul rate-adaptBronze Queue..................................... DisabledGold Queue....................................... EnabledPlatinum Queue................................... DisabledSilver Queue..................................... DisabledRelated Commands
config mesh battery-state
show mesh config
show mesh statsshow mesh cac
To display call admission control (CAC) topology and the bandwidth used or available in a mesh network, use the show mesh cac command.
show mesh cac {summary | {bwused {voice | video} | access | callpath | rejected} cisco_ap}
Syntax Description
Defaults
None.
Examples
This example shows how to display a summary of the call admission control settings:
> show mesh cac summaryAP Name Slot# Radio BW Used/Max Calls----------------- ------- ----- ----------- -----SB_RAP1 0 11b/g 0/23437 01 11a 0/23437 0SB_MAP1 0 11b/g 0/23437 01 11a 0/23437 0SB_MAP2 0 11b/g 0/23437 01 11a 0/23437 0SB_MAP3 0 11b/g 0/23437 01 11a 0/23437 0This example shows how to display the mesh topology and the voice bandwidth used or available:
> show mesh cac bwused voice SB_MAP1AP Name Slot# Radio BW Used/Max------------- ------- ----- -----------SB_RAP1 0 11b/g 0/234371 11a 0/23437| SB_MAP1 0 11b/g 0/234371 11a 0/23437|| SB_MAP2 0 11b/g 0/234371 11a 0/23437||| SB_MAP3 0 11b/g 0/234371 11a 0/23437This example shows how to display the access voice calls in progress in a tree topology:
> show mesh cac access 1524_Map1AP Name Slot# Radio Calls------------- ------- ----- -----1524_Rap 0 11b/g 01 11a 02 11a 0| 1524_Map1 0 11b/g 01 11a 02 11a 0|| 1524_Map2 0 11b/g 01 11a 02 11a 0Related Commands
config 802.11 cac video acm
config 802.11 cac video max-bandwidth
config 802.11 cac video roam-bandwidth
config 802.11 cac video tspec-inactivity-timeout
config 802.11 cac voice acm
config 802.11 cac voice max-bandwidth
config 802.11 cac voice roam-bandwidth
config 802.11 cac voice tspec-inactivity-timeout
config 802.11 cac voice load-based
debug cacshow mesh client-access
To display the backhaul client access configuration setting, use the show mesh client-access command.
show mesh client-access
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display backhaul client access configuration settings for a mesh access point:
> show mesh client-accessBackhaul with client access status: enabledRelated Commands
show mesh config
To display mesh configuration settings, use the show mesh config command.
show mesh config
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display global mesh configuration settings:
> show mesh configMesh Range....................................... 12000Mesh Statistics update period.................... 3 minutesBackhaul with client access status............... disabledBackhaul with extended client access status...... disabledBackground Scanning State........................ enabledBackhaul Amsdu State............................. disabledMesh SecuritySecurity Mode................................. EAPExternal-Auth................................. disabledUse MAC Filter in External AAA server......... disabledForce External Authentication................. disabledMesh Alarm CriteriaMax Hop Count................................. 4Recommended Max Children for MAP.............. 10Recommended Max Children for RAP.............. 20Low Link SNR.................................. 12High Link SNR................................. 60Max Association Number........................ 10Association Interval.......................... 60 minutesParent Change Numbers......................... 3Parent Change Interval........................ 60 minutesMesh Multicast Mode.............................. In-OutMesh Full Sector DFS............................. enabledMesh Ethernet Bridging VLAN Transparent Mode..... disabledMesh DCA channels for serial backhaul APs........ enabledRelated Commands
show mesh stats
show mgmtuser
config mesh alarmshow mesh env
To display global or specific environment summary information for mesh networks, use the show mesh env command.
show mesh env {summary | cisco_ap}
Syntax Description
summary
Displays global environment summary information.
cisco_ap
Name of access point for which environment summary information is requested.
Defaults
None.
Examples
This example shows how to display global environment summary information:
> show mesh env summaryAP Name Temperature(C) Heater Ethernet Battery------------------ -------------- ------ -------- -------ap1130:5f:be:90 N/A N/A DOWN N/AAP1242:b2.31.ea N/A N/A DOWN N/AAP1131:f2.8d.92 N/A N/A DOWN N/AAP1131:46f2.98ac N/A N/A DOWN N/Aap1500:62:39:70 -36 OFF UP N/AThis example shows how to display an environment summary for an access point:
> show mesh env SB_RAP1AP Name.......................................... SB_RAP1AP Model......................................... AIR-LAP1522AG-A-K9AP Role.......................................... RootAPTemperature...................................... 21 C, 69 FHeater........................................... OFFBackhaul......................................... GigabitEthernet0GigabitEthernet0 Status.......................... UPDuplex....................................... FULLSpeed........................................ 100Rx Unicast Packets........................... 114754Rx Non-Unicast Packets....................... 1464Tx Unicast Packets........................... 9630Tx Non-Unicast Packets....................... 3331GigabitEthernet1 Status.......................... DOWNPOE Out........................................ OFFBattery.......................................... N/A
Note
Related Commands
show mesh neigh
To display summary or detailed information about the mesh neighbors for a specific mesh access point, use the show mesh neigh command.
show mesh neigh {detail | summary} {cisco_ap | all}
Syntax Description
Note
Examples
This example shows how to display a neighbor summary of an access point:
> show mesh neigh summary ap1500:62:39:70AP Name/Radio Mac Channel Snr-Up Snr-Down Link-Snr Flags State----------------- ------- ------ -------- -------- ------ -------mesh-45-rap1 165 15 18 16 0x86b UPDATED NEIGH PARENT BEACON00:0B:85:80:ED:D0 149 5 6 5 0x1a60 NEED UPDATE BEACON DEFAULT00:17:94:FE:C3:5F 149 7 0 0 0x860 BEACONThis example shows how to display the detailed neighbor statistics of an access point:
> show mesh neigh detail ap1500:62:39:70AP MAC : 00:1E:BD:1A:1A:00 AP Name: HOR1522_MINE06_MAP_S_DykeFLAGS : 860 BEACONworstDv 255, Ant 0, channel 153, biters 0, ppiters 0Numroutes 0, snr 0, snrUp 8, snrDown 8, linkSnr 8adjustedEase 0, unadjustedEase 0txParent 0, rxParent 0poorSnr 0lastUpdate 2483353214 (Sun Aug 4 23:51:58 1912)parentChange 0Per antenna smoothed snr values: 0 0 0 0Vector through 00:1E:BD:1A:1A:00Table 2-4 lists the output flags displayed for the config mesh linktest command.
Related Commands
show mesh path
To display the channel and signal-to-noise ratio (SNR) details for a link between a mesh access point and its neighbor, use the show mesh path command.
show mesh path cisco_ap
Syntax Description
Defaults
None.
Examples
This example shows how to display channel and SNR details for a designated link path:
> show mesh path mesh-45-rap1AP Name/Radio Mac Channel Snr-Up Snr-Down Link-Snr Flags State----------------- ------- ------ -------- -------- ------ -------mesh-45-rap1 165 15 18 16 0x86b UPDATED NEIGH PARENT BEACONmesh-45-rap1 is a Root AP.Related Commands
config mesh battery-state
config mesh client-access
config mesh linktest
config mesh range
show mesh config
show mesh neigh
show mesh statsshow mesh per-stats
To display the percentage of packet errors for packets transmitted by the neighbors of a specified mesh access point, use the show mesh per-stats command.
show mesh per-stats summary {cisco_ap | all}
Syntax Description
summary
Displays the packet error rate stats summary.
cisco_ap
Name of mesh access point.
all
Displays all mesh access points.
Note
Defaults
None.
Usage Guidelines
The packet error rate percentage equals 1, which is the number of successfully transmitted packets divided by the number of total packets transmitted.
Examples
This example shows how to display the percentage of packet errors for packets transmitted by the neighbors to a mesh access point:
> show mesh per-stats summary ap_12Neighbor MAC Address 00:0B:85:5F:FA:F0Total Packets transmitted: 104833Total Packets transmitted successfully: 104833Total Packets retried for transmission: 33028Neighbor MAC Address: 00:0B:85:80:ED:D0Total Packets transmitted: 0Total Packets transmitted successfully: 0Total Packets retried for transmission: 0Neighbor MAC Address: 00:17:94:FE:C3:5FTotal Packets transmitted: 0Total Packets transmitted successfully: 0Total Packets retried for transmission: 0Related Commands
config mesh linktest
config mesh range
show mesh config
show mesh neigh
show mesh statsshow mesh queue-stats
To display the number of packets in a client access queue by type for a particular mesh access point, use the show mesh queue-stats command.
show mesh queue-stats {cisco_ap | all}
Syntax Description
cisco_ap
Name of access point for which you want packet queue statistics.
all
Displays all access points.
Note
Defaults
None.
Examples
This example shows how to display packet queue statistics for access point ap417:
> show mesh queue-stats ap417Queue Type Overflows Peak length Average length---------- --------- ----------- --------------Silver 0 1 0.000Gold 0 4 0.004Platinum 0 4 0.001Bronze 0 0 0.000Management 0 0 0.000Related Commands
config mesh client-access
config mesh multicast
config mesh secondary-backhaul
show mesh client-access
show mesh config
show mesh stats
show mgmtusershow mesh public-safety
To display 4.8-GHz public safety settings, use the show mesh public-safety command.
show mesh public-safety
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to view 4.8-GHz public safety settings:
> show mesh public-safetyGlobal Public Safety status: disabledRelated Commands
config 802.11-a
config 802.11-a antenna extAntGain
config 802.11-a channel ap
config 802.11-a txpower ap
config mesh public-safety
config mesh security
show mesh ap
show mesh security-stats
show mesh statsshow mesh secbh-stats
To display queue statistics for secondary backhaul access in a mesh network, use the show mesh secbh-stats command.
show mesh secbh-stats {cisco_ap | all}
Syntax Description
Note
Defaults
None.
Usage Guidelines
The secondary backhaul access feature is not supported by Cisco 1520 and 1524 indoor mesh access points in the 5.2 release.
Examples
This example shows how to display statistics for secondary backhaul access of access point SB_RAP1:
> show mesh secbh-stats SB_RAP1Radio Type: 802.11BGQueue:Silver:Packet retries: 0Packets dropped after max retries: 0Queue:Gold:Packet retries: 0Packets dropped after max retries: 0Queue:Platinum:Packet retries: 0Packets dropped after max retries: 0Radio Type: 802.11AQueue:Silver:Packet retries: 0Packets dropped after max retries: 0Queue:Gold:Packet retries: 0Packets dropped after max retries: 0Queue:Platinum:Packet retries: 0Packets dropped after max retries: 0Related Commands
config mesh secondary-backhaul
show mesh secondary-backhaulshow mesh secondary-backhaul
To display the current state of mesh secondary backhaul configuration settings, use the show mesh secondary-backhaul command.
show mesh secondary-backhaul
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Usage Guidelines
The secondary backhaul access feature is not supported by Cisco 1520 and 1524 indoor mesh access points in the 5.2 release.
Examples
This example shows how to display secondary backhaul configuration settings for a mesh access point:
> show mesh secondary-backhaulMESH secondary-backhaul: enabledRelated Commands
config mesh secondary-backhaul
show mesh secbh-statsshow mesh security-stats
To display packet error statistics for a specific access point, use the show mesh security-stats command.
show mesh security-stats {cisco_ap | all}
Syntax Description
cisco_ap
Name of access point for which you want packet error statistics.
all
Displays all access points.
Note
Defaults
None.
Usage Guidelines
This command shows packet error statistics and a count of failures, timeouts, and successes with respect to associations and authentications as well as reassociations and reauthentications for the specified access point and its child.
Examples
This example shows how to display packet error statistics for access point ap417:
> show mesh security-stats ap417AP MAC : 00:0B:85:5F:FA:F0Packet/Error Statistics:-----------------------------x Packets 14, Rx Packets 19, Rx Error Packets 0Parent-Side Statistics:--------------------------Unknown Association Requests 0Invalid Association Requests 0Unknown Re-Authentication Requests 0Invalid Re-Authentication Requests 0Unknown Re-Association Requests 0Invalid Re-Association Requests 0Unknown Re-Association Requests 0Invalid Re-Association Requests 0Child-Side Statistics:--------------------------Association Failures 0Association Timeouts 0Association Successes 0Authentication Failures 0Authentication Timeouts 0Authentication Successes 0Re-Association Failures 0Re-Association Timeouts 0Re-Association Successes 0Re-Authentication Failures 0Re-Authentication Timeouts 0Re-Authentication Successes 0Related Commands
config mesh alarm
config mesh linkdata
config mesh linktest
config mesh securityshow mesh stats
To display the mesh statistics for a Cisco lightweight access point, use the show mesh stats command.
show mesh stats cisco_ap
Syntax Description
Defaults
None.
Examples
This example shows how to display statistics of an access point:
> show mesh stats RAP_ap1RAP in state MaintrxNeighReq 759978, rxNeighRsp 568673txNeighReq 115433, txNeighRsp 759978rxNeighUpd 8266447 txNeighUpd 693062tnextchan 0, nextant 0, downAnt 0, downChan 0, curAnts 0tnextNeigh 0, malformedNeighPackets 244, poorNeighSnr 27901blacklistPackets 0, insufficientMemory 0authenticationFailures 0Parent Changes 1, Neighbor Timeouts 16625Related Commands
config mesh alarm
config mesh client-access
config mesh ethernet-bridging vlan-transparent
config mesh linkdata
config mesh linktest
config mesh security
show mesh per-stats
show mesh queue-stats
show mesh security-statsshow mgmtuser
To display the local management user accounts on the Cisco wireless LAN controller, use the show mgmtuser command.
show mgmtuser
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a list of management users:
> show mgmtuserusername Permissions Description----------------------- ------------ --------------------------------admin read-writeRelated Commands
config mgmtuser add
config mgmtuser delete
config mgmtuser description
config mgmtuser passwordShow Mobility Commands
Use the show mobility commands to display mobility settings.
show mobility anchor
To display the wireless LAN anchor export list for the Cisco wireless LAN controller mobility groups or to display a list and status of controllers configured as mobility anchors for a specific WLAN or wired guest LAN, use the show mobility anchor commands.
show mobility anchor [wan wlan_id | guest-lan guest_lan_id]
Syntax Description
Defaults
None.
Usage Guidelines
The status field display (see example) shows one of the following values:
•
•
•
•
Examples
This example shows how to display a mobility wireless LAN anchor list:
> show mobility anchorMobility Anchor Export ListWLAN ID IP Address Status------- --------------- ------12 192.168.0.15 UPGLAN ID IP Address Status------- --------------- -------1 192.168.0.9 CNTRL_DATA_PATH_DOWNRelated Commands
config guest-lan mobility anchor
config mobility group domain
config mobility group keepalive count
config mobility group keepalive interval
config mobility group member
config mobility group multicast-addres
config mobility multicast-mode
config mobility secure-mode
config mobility statistics reset
config wlan mobility anchor
debug mobility
show mobility anchor
show mobility statistics
show mobility summaryshow mobility statistics
To display the statistics information for the Cisco wireless LAN controller mobility groups, use the show mobility statistics command.
show mobility statistics
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display statistics of the mobility manager:
> show mobility statisticsGlobal Mobility StatisticsRx Errors..................................... 0Tx Errors..................................... 0Responses Retransmitted....................... 0Handoff Requests Received..................... 0Handoff End Requests Received................. 0State Transitions Disallowed.................. 0Resource Unavailable.......................... 0Mobility Initiator StatisticsHandoff Requests Sent......................... 0Handoff Replies Received...................... 0Handoff as Local Received..................... 2Handoff as Foreign Received................... 0Handoff Denys Received........................ 0Anchor Request Sent........................... 0Anchor Deny Received.......................... 0Anchor Grant Received......................... 0Anchor Transfer Received...................... 0Mobility Responder StatisticsHandoff Requests Ignored...................... 0Ping Pong Handoff Requests Dropped............ 0Handoff Requests Dropped...................... 0Handoff Requests Denied....................... 0Client Handoff as Local....................... 0Client Handoff as Foreign ................... 0Client Handoff Inter Group ................... 0Anchor Requests Received...................... 0Anchor Requests Denied........................ 0Anchor Requests Granted....................... 0Anchor Transferred............................ 0Related Commands
config mobility group anchor
config mobility group domain
config mobility group keepalive count
config mobility group keepalive interval
config mobility group member
config mobility group multicast-addres
config mobility multicast-mode
config mobility secure-mode
config mobility statistics reset
debug mobility
show mobility anchor
show mobility summaryshow mobility summary
To display the summary information for the Cisco wireless LAN controller mobility groups, use the show mobility summary command.
show mobility summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Usage Guidelines
Some WLAN controllers may list no mobility security mode.
Examples
This example shows how to display a summary of the mobility manager:
> show mobility summarySymmetric Mobility Tunneling (current) .......... DisabledSymmetric Mobility Tunneling (after reboot) ..... DisabledMobility Protocol Port........................... 16666Mobility Security Mode........................... DisabledDefault Mobility Domain.......................... snmp_guiMulticast Mode .................................. DisabledMobility Domain ID for 802.11r................... 0x66bdMobility Keepalive Interval...................... 10Mobility Keepalive Count......................... 3Mobility Group Members Configured................ 1Mobility Control Message DSCP Value.............. 0Controllers configured in the Mobility GroupMAC Address IP Address Group Name Multicast IP Status00:1b:d4:6b:87:20 1.100.163.70 snmp_gui 0.0.0.0 UpRelated Commands
config guest-lan mobility anchor
config mobility group domain
config mobility group keepalive count
config mobility group keepalive interval
config mobility group member
config mobility group multicast-addres
config mobility multicast-mode
config mobility secure-mode
config mobility statistics reset
config wlan mobility anchor
debug mobility
show mobility anchor
show mobility statisticsshow msglog
To display the message logs written to the Cisco wireless LAN controller database, use the show msglog command.
show msglog
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Usage Guidelines
If there are more that 15 entries, you are prompted to display the messages shown in the example.
Examples
This example shows how to display message logs:
> show msglogMessage Log Severity Level..................... ERRORThu Aug 4 14:30:08 2005 [ERROR] spam_lrad.c 1540: AP 00:0b:85:18:b6:50 associated. Last AP failure was due to Link FailureThu Aug 4 14:30:08 2005 [ERROR] spam_lrad.c 13840: Updating IP info for AP 00:0b:85:18:b6:50 -- static 0, 1.100.49.240/255.255.255.0, gtw 1.100.49.1Thu Aug 4 14:29:32 2005 [ERROR] dhcpd.c 78: dhcp server: binding to 0.0.0.0Thu Aug 4 14:29:32 2005 [ERROR] rrmgroup.c 733: Airewave Director: 802.11a switch group resetThu Aug 4 14:29:32 2005 [ERROR] rrmgroup.c 733: Airewave Director: 802.11bg switch group resetThu Aug 4 14:29:22 2005 [ERROR] sim.c 2841: Unable to get link state for primary port 0 of interface ap-managerThu Aug 4 14:29:22 2005 [ERROR] dtl_l2_dot1q.c 767: Unable to get USPThu Aug 4 14:29:22 2005 Previous message occurred 2 timesThu Aug 4 14:29:14 2005 [CRITICAL] osapi_sem.c 794: Error! osapiMutexTake called with NULL pointer: osapi_bsntime.c:927Thu Aug 4 14:29:14 2005 [CRITICAL] osapi_sem.c 794: Error! osapiMutexTake called with NULL pointer: osapi_bsntime.c:919Thu Aug 4 14:29:14 2005 [CRITICAL] hwutils.c 1861: Security Module not foundThu Aug 4 14:29:13 2005 [CRITICAL] bootos.c 791: Starting code...show nac statistics
To display detailed Network Access Control (NAC) information about a Cisco wireless LAN controller, use the show nac statistics command.
show nac statistics
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display detailed statistics of network access control settings:
> show nac statisticsServer Index....................................................... 1Server Address..................................................... xxx.xxx.xxx.xxxNumber of requests sent............................................ 0Number of retransmissions.......................................... 0Number of requests received........................................ 0Number of malformed requests received.............................. 0Number of bad auth requests received............................... 0Number of pending requests......................................... 0Number of timed out requests....................................... 0Number of misc dropped request received............................ 0Number of requests sent............................................ 0Related Commands
show nac summary
config guest-lan nac
config wlan nac
debug nacshow nac summary
To display NAC summary information for a Cisco wireless LAN controller, use the show nac summary command.
show nac summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a summary information of network access control settings:
> show nac summaryNAC ACL Name ...............................................Index Server Address Port State----- ---------------------------------------- ---- -----1 xxx.xxx.xxx.xxx 13336 EnabledRelated Commands
show nac statistics
config guest-lan nac
config wlan nac
debug nacshow netuser
To display the configuration of a particular user in the local user database, use show netuser command.
show netuser summary.
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a summary of all users in the local user database:
> show netuser summaryMaximum logins allowed for a given username ........UnlimitedThis example shows how to display detailed information on the specifies network user:
> show netuser detail john10username........................................... abcWLAN Id............................................. AnyLifetime............................................ PermanentDescription......................................... test userRelated Commands
config netuser add
config netuser delete
config netuser description
config netuser guest-role apply
config netuser wlan-id
show netuser guest-rolesshow netuser guest-roles
To display a list of the current quality of service (QoS) roles and their bandwidth parameters, use the show netuser guest-roles command.
show netuser guest-roles
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a QoS role for the guest network user:
> show netuser guest-rolesRole Name.............................. ContractorAverage Data Rate.................. 10Burst Data Rate.................... 10Average Realtime Rate.............. 100Burst Realtime Rate................ 100Role Name.............................. VendorAverage Data Rate.................. unconfiguredBurst Data Rate.................... unconfiguredAverage Realtime Rate.............. unconfiguredBurst Realtime Rate................ unconfiguredRelated Commands
config netuser add
config netuser delete
config netuser description
config netuser guest-role apply
config netuser wlan-id
show netuser guest-roles
show netusershow network
To display the current status of 802.3 bridging for all WLANs, use the show network command.
show network
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the network details:
> show networkRelated Commands
Configure Network Commands
show network summary
show network multicast mgid detail
show network multicast mgid summaryshow network summary
To display the network configuration of the Cisco wireless LAN controller, use the show network summary command.
show network summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a summary configuration:
> show network summaryRF-Network Name............................. RFWeb Mode.................................... DisableSecure Web Mode............................. EnableSecure Web Mode Cipher-Option High.......... DisableSecure Web Mode Cipher-Option SSLv2......... DisableSecure Shell (ssh).......................... EnableTelnet...................................... EnableEthernet Multicast Mode..................... Disable Mode: UcastEthernet Broadcast Mode..................... DisableIGMP snooping............................... DisabledIGMP timeout................................ 60 secondsUser Idle Timeout........................... 300 secondsARP Idle Timeout............................ 300 secondsARP Unicast Mode............................ DisabledCisco AP Default Master..................... DisableMgmt Via Wireless Interface................. DisableMgmt Via Dynamic Interface.................. DisableBridge MAC filter Config.................... EnableBridge Security Mode........................ EAPOver The Air Provisioning of AP's........... EnableApple Talk ................................. DisableRelated Commands
Configure Network Commands
show network
show network multicast mgid detail
show network multicast mgid summaryshow network multicast mgid detail
To display all the clients joined to the multicast group in a specific multicast group identification (MGID), use the show network multicast mgid detail command.
show network multicast mgid detail mgid_value
Syntax Description
Defaults
None.
Examples
This example shows how to display details of the multicast database:
> show network multicast mgid detailMgid ............................... 550Multicast Group Address ............ 239.255.255.250Vlan ............................... 0Rx Packet Count .................... 807399588No of clients ...................... 1Client List ........................Client MAC Expire TIme (mm:ss)00:13:02:23:82:ad 0:20Related Commands
show network
show network summary
show network multicast mgid summaryshow network multicast mgid summary
To display all the multicast groups and their corresponding multicast group identifications (MGIDs), use the show network multicast mgid summary command.
show network multicast mgid summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a summary of multicast groups and their MGIDs:
> show network multicast mgid summaryLayer2 MGID Mapping:-------------------InterfaceName vlanId MGID----------------------------- ------ -----management 0 0test 0 9wired 20 8Layer3 MGID Mapping:-------------------Number of Layer3 MGIDs ................ 1Group address Vlan MGID------------------ ----- ------239.255.255.250 0 550Related Commands
show network
show network summary
show network multicast mgid detailshow nmsp notify-interval summary
To display the Network Mobility Services Protocol (NMSP) configuration settings, use the show nmsp notify-interval summary command.
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display NMSP configuration settings:
> show nmsp notify-interval summaryNMSP Notification Interval SummaryClientMeasurement interval: 2 secRFIDMeasurement interval: 8 secRogue APMeasurement interval: 2 secRogue ClientMeasurement interval: 2 secRelated Commands
clear locp statistics
clear nmsp statistics
config nmsp notify-interval measurement
show nmsp statistics
show nmsp status
show nmsp statistics
To display Network Mobility Services Protocol (NMSP) counters, use the show nmsp statistics command.
show nmsp statistics {summary | connection all}
Syntax Description
Defaults
None.
Examples
This example shows how to display a summary of common NMSP counters:
> show nmsp statistics summarySend RSSI with no entry: 0Send too big msg: 0Failed SSL write: 0Partial SSL write: 0SSL write attempts to want write:Transmit Q full:0Max Measure Notify Msg: 0Max Info Notify Msg: 0Max Tx Q Size: 2Max Rx Size: 1Max Info Notify Q Size: 0Max Client Info Notify Delay: 0Max Rogue AP Info Notify Delay: 0Max Rogue Client Info Notify Delay: 0Max Client Measure Notify Delay: 0Max Tag Measure Notify Delay: 0Max Rogue AP Measure Notify Delay: 0Max Rogue Client Measure Notify Delay: 0Max Client Stats Notify Delay: 0Max Tag Stats Notify Delay: 0RFID Measurement Periodic : 0RFID Measurement Immediate : 0Reconnect Before Conn Timeout: 0This example shows how to display all the connection-specific NMSP counters:
> show nmsp statistics connection allNMSP Connection CountersConnection 1 :Connection status: UPFreed Connection: 0Nmsp Subscr Req: 0 NMSP Subscr Resp: 0Info Req: 1 Info Resp: 1Measure Req: 2 Measure Resp: 2Stats Req: 2 Stats Resp: 2Info Notify: 0 Measure Notify: 0Loc Capability: 2Location Req: 0 Location Rsp: 0Loc Subscr Req: 0 Loc Subscr Rsp: 0Loc Notif: 0Loc Unsubscr Req: 0 Loc Unsubscr Rsp: 0IDS Get Req: 0 IDS Get Resp: 0IDS Notif: 0IDS Set Req: 0 IDS Set Resp: 0Related Commands
clear nmsp statistics
config nmsp notify-interval measurement
show nmsp notify-interval summary
show nmsp status
show nmsp status
To display the status of active Network Mobility Services Protocol (NMSP) connections, use the show nmsp status command.
show nmsp status
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the status of the active NMSP connections:
>show nmsp status
LocServer IP TxEchoResp RxEchoReq TxData RxData-------------- ----------- --------- ------- -------171.71.132.158 21642 21642 51278 21253Related Commands
clear locp statistics
clear nmsp statistics
config nmsp notify-interval measurement
show nmsp notify-interval summary
show nmsp statisticsshow nmsp subscription
To display the Network Mobility Services Protocol (NMSP) services that are active on the controller, use the show nmsp subscription command.
show nmsp subscription {summary | detail ip_addr}
Syntax Description
Defaults
None.
Examples
This example shows how to display a summary of all the NMSP services to which the controller is subscribed:
> show nmsp subscription summaryMobility Services Subscribed:Server IP Services--------- --------10.10.10.31 RSSI, Info, StatisticsThis example shows how to display details of all the NMSP services:
> show nmsp subscription detail 10.10.10.31Mobility Services Subscribed by 10.10.10.31Services Sub-services-------- ------------RSSI Mobile Station, Tags,Info Mobile Station,Statistics Mobile Station, Tags,Related Commands
clear locp statistics
clear nmsp statistics
config nmsp notify-interval measurement
show nmsp notify-interval summary
show nmsp statisticsshow pmk-cache
To display information about the pairwise master key (PMK) cache, use the show port command.
show pmk-cache {all | MAC}
Syntax Description
all
Displays information about all entries in the PMK cache.
MAC
Information about a single entry in the PMK cache.
Defaults
None.
Examples
This example shows how to display information about a single entry in the PMK cache:
> show pmk-cache xx:xx:xx:xx:xx:xxThis example shows how to display information about all entries in the PMK cache:
> show pmk-cache allPMK CacheEntryStation Lifetime VLAN Override IP Override----------------- -------- -------------------- ---------------Related Commands
show port
To display the Cisco wireless LAN controller port settings on an individual or global basis, use the show port command.
show port {port | summary}
Syntax Description
Defaults
None.
Examples
This example shows how to display information about an individual wireless LAN controller port:
> show port 1STP Admin Physical Physical Link Link McastPr Type Stat Mode Mode Status Status Trap Appliance POE-- ------- ---- ------- ---------- ---------- ------ ------- --------- -------1 Normal Disa Enable Auto 1000 Full Down Enable Enable N/A
Note
This example shows how to display a summary of all ports:
> show port summarySTP Admin Physical Physical Link Link McastPr Type Stat Mode Mode Status Status Trap Appliance POE-- ------- ---- ------- ---------- ---------- ------ ------- --------- -------1 Normal Forw Enable Auto 1000 Full Up Enable Enable N/A2 Normal Disa Enable Auto 1000 Full Down Enable Enable N/A3 Normal Disa Enable Auto 1000 Full Down Enable Enable N/A4 Normal Disa Enable Auto 1000 Full Down Enable Enable N/A
Note
Related Commands
clear stats port
config ap port
config interface port
config network web-auth-port
Configure Port Commands
config spanningtree port mode
config spanningtree port pathcost
config spanningtree port priority
show stats portshow process
To display how various processes in the system are using the CPU at that instant in time, use the show process commands.
show process {cpu | memory}
Syntax Description
cpu
Displays how various system tasks are using the CPU at that moment.
memory
Displays the allocation and deallocation of memory from various processes in the system at that moment.
Defaults
None.
Usage Guidelines
This command is helpful in understanding if any single task is monopolizing the CPU and preventing other tasks from being performed.
Examples
This example shows how to display various tasks in the system that are using the CPU at a given moment:
> show process cpuName Priority CPU Use ReaperreaperWatcher ( 3/124) 0 % ( 0/ 0)% IosapiReaper (10/121) 0 % ( 0/ 0)% ITempStatus (255/ 1) 0 % ( 0/ 0)% IemWeb (255/ 1) 0 % ( 0/ 0)% T 300cliWebTask (255/ 1) 0 % ( 0/ 0)% IUtilTask (255/ 1) 0 % ( 0/ 0)% T 300This example shows how to display the allocation and deallocation of memory from various processes at a given moment:
> show process memoryName Priority BytesinUse ReaperreaperWatcher ( 3/124) 0 ( 0/ 0)% IosapiReaper (10/121) 0 ( 0/ 0)% ITempStatus (255/ 1) 308 ( 0/ 0)% IemWeb (255/ 1) 294440 ( 0/ 0)% T 300cliWebTask (255/ 1) 738 ( 0/ 0)% IUtilTask (255/ 1) 308 ( 0/ 0)% T 300Related Commands
debug memory
transfer upload datatypeshow qos queue_length all
To display quality of service (QoS) information (queue length), use the show qos queue-length all command.
show qos queue_length all
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display QoS queue length information:
> show qos queue_length allPlatinum queue length.......................... 255Gold queue length.............................. 255Silver queue length............................ 150Bronze queue length............................ 100Related Commands
Show RADIUS Commands
Use the show radius commands to display RADIUS settings.
show radius acct statistics
To display the RADIUS accounting server statistics for the Cisco wireless LAN controller, use the show radius acct statistics command.
show radius acct statistics
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display RADIUS accounting server statistics:
> show radius acct statisticsAccounting Servers:Server Index..................................... 1Server Address................................... 10.1.17.10Msg Round Trip Time.............................. 0 (1/100 second)First Requests................................... 0Retry Requests................................... 0Accounting Responses............................. 0Malformed Msgs................................... 0Bad Authenticator Msgs........................... 0Pending Requests................................. 0Timeout Requests................................. 0Unknowntype Msgs................................. 0Other Drops...................................... 0Related Commands
config radius acct
config radius acct IPsec authentication
config radius acct IPsec disable
config radius acct network
show radius auth statistics
show radius summaryshow radius auth statistics
To display the RADIUS authentication server statistics for the Cisco wireless LAN controller, use the show radius auth statistics command.
show radius auth statistics
Syntax Description
This command has no arguments or keyword.
Defaults
None.
Examples
This example shows how to display RADIUS authentication server statistics:
> show radius auth statisticsAuthentication Servers:Server Index..................................... 1Server Address................................... 1.1.1.1Msg Round Trip Time.............................. 0 (1/100 second)First Requests................................... 0Retry Requests................................... 0Accept Responses................................. 0Reject Responses................................. 0Challenge Responses.............................. 0Malformed Msgs................................... 0Bad Authenticator Msgs........................... 0Pending Requests................................. 0Timeout Requests................................. 0Unknowntype Msgs................................. 0Other Drops...................................... 0Related Commands
config radius auth
config radius auth management
config radius auth network
show radius summaryshow radius rfc3576 statistics
To display the RADIUS rfc3576 server statistics for the Cisco wireless LAN controller, use the show radius rfc3576 statistics command.
show radius rfc3576 statistics
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Usage Guidelines
RFC 3576, an extension to the RADIUS protocol, allows dynamic changes to a user session, which includes support for disconnecting users and changing authorizations applicable to a user session; that is, it provides support for Disconnect and Change-of-Authorization (CoA) messages. Disconnect messages cause a user session to be terminated immediately. CoA messages modify session authorization attributes such as data filters.
Examples
This example shows how to display the RADIUS RFC-3576 server statistics:
> show radius rfc3576 statisticsRFC-3576 Servers:Server Index..................................... 1Server Address................................... 10.1.17.10Msg Round Trip Time.............................. 0 (1/100 second)First Requests................................... 0Retry Requests................................... 0Accounting Responses............................. 0Malformed Msgs................................... 0Bad Authenticator Msgs........................... 0Pending Requests................................. 0Timeout Requests................................. 0Unknown type Msgs................................. 0Other Drops...................................... 0Related Commands
config radius auth rfc3576
show radius auth statistics
show radius summary
show radius summary
To display the RADIUS authentication and accounting server summary, use the show radius summary command.
show radius summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a RADIUS authentication server summary:
> show radius summaryVendor Id Backward Compatibility................. DisabledCredentials Caching.............................. DisabledCall Station Id Type............................. IP AddressAdministrative Authentication via RADIUS......... EnabledAuthentication ServersIndex Type Server Address Port State Tout RFC-3576 IPsec - AuthMode/Phase1/Group/Lifetime/Auth/Encr----- ---- ---------------- ------ -------- ---- -------- ------------------------------------------------Accounting ServersIndex Type Server Address Port State Tout RFC-3576 IPsec - AuthMode/Phase1/Group/Lifetime/Auth/Encr----- ---- ---------------- ------ -------- ---- -------- ------------------------------------------------Related Commands
show radius acct statistics
show radius auth statisticsShow Radio Frequency ID Commands
Use the show rfid commands to display radio frequency ID settings.
show rfid client
To display the radio frequency identification (RFID) tags that are associated to the controller as clients, use the show rfid client command.
show rfid client
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Usage Guidelines
When the RFID tag is not in client mode, the above fields are blank.
Examples
This example shows how to display the RFID tag that is associated to the controller as clients:
> show rfid client------------------ -------- --------- ----------------- ------ ----------------HeardRFID Mac VENDOR Sec Ago Associated AP Chnl Client State------------------ -------- --------- ----------------- ------ ----------------00:14:7e:00:0b:b1 Pango 35 AP0019.e75c.fef4 1 ProbingRelated Commands
config rfid status
config rfid timeout
show rfid config
show rfid detail
show rfid summaryshow rfid config
To display the current radio frequency identification (RFID) configuration settings, use the show rfid config command.
show rfid config
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the current RFID configuration settings:
> show rfid configRFID Tag Data Collection ............................... EnabledRFID Tag Auto-Timeout .................................. EnabledRFID Client Data Collection ............................ DisabledRFID Data Timeout ...................................... 200 secondsRelated Commands
config rfid status
config rfid timeout
show rfid client
show rfid detail
show rfid summaryshow rfid detail
To display detailed radio frequency identification (RFID) information for a specified tag, use the show rfid detail command.
show rfid detail mac_address
Syntax Description
Defaults
None.
Examples
This example shows how to display detailed RFID information:
> show rfid detail 32:21:3a:51:01:02RFID address..................................... 00:12:b8:00:20:52Vendor........................................... G2Last Heard....................................... 51 seconds agoPackets Received................................. 2Bytes Received................................... 324Cisco Type.......................................Content Header=================Version.......................................... 0Tx Power......................................... 12 dBmChannel.......................................... 1Reg Class........................................ 12Burst Length..................................... 1CCX Payload===========Last Sequence Control............................ 0Payload length................................... 127Payload Data Hex Dump01 09 00 00 00 00 0b 85 52 52 52 02 07 4b ff ff7f ff ff ff 03 14 00 12 7b 10 48 53 c1 f7 51 4b50 ba 5b 97 27 80 00 67 00 01 03 05 01 42 34 0000 03 05 02 42 5c 00 00 03 05 03 42 82 00 00 0305 04 42 96 00 00 03 05 05 00 00 00 55 03 05 0642 be 00 00 03 02 07 05 03 12 08 10 00 01 02 0304 05 06 07 08 09 0a 0b 0c 0d 0e 0f 03 0d 09 0308 05 07 a8 02 00 10 00 23 b2 4e 03 02 0a 03Nearby AP Statistics:lap1242-2(slot 0, chan 1) 50 seconds ag.... -76 dBmlap1242(slot 0, chan 1) 50 seconds ago..... -65 dBmRelated Commands
config rfid status
config rfid timeout
show rfid config
show rfid client
show rfid summaryshow rfid summary
To display a summary of the radio frequency identification (RFID) information for a specified tag, use the show rfid summary command.
show rfid summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a summary of RFID information:
> show rfid summaryTotal Number of RFID : 5----------------- -------- ------------------ ------ ---------------------RFID ID VENDOR Closest AP RSSI Time Since Last Heard----------------- -------- ------------------ ------ ---------------------00:04:f1:00:00:04 Wherenet ap:1120 -51 858 seconds ago00:0c:cc:5c:06:d3 Aerosct ap:1120 -51 68 seconds ago00:0c:cc:5c:08:45 Aerosct AP_1130 -54 477 seconds ago00:0c:cc:5c:08:4b Aerosct wolverine -54 332 seconds ago00:0c:cc:5c:08:52 Aerosct ap:1120 -51 699 seconds agoRelated Commands
config rfid status
config rfid timeout
show rfid client
show rfid config
show rfid detail
Show Rogue Commands
Use the show rogue commands to display unverified (rogue) device settings.
show rogue adhoc detailed
To display details of an ad-hoc rogue access point detected by the Cisco wireless LAN controller, use the show rogue adhoc client detailed command.
show rogue adhoc detailed MAC
Syntax Description
Defaults
None.
Examples
This example shows how to display detailed ad-hoc rogue MAC address information:
> show rogue adhoc detailed 02:61:ce:8e:a8:8cAdhoc Rogue MAC address.......................... 02:61:ce:8e:a8:8cAdhoc Rogue BSSID................................ 02:61:ce:8e:a8:8cState............................................ AlertFirst Time Adhoc Rogue was Reported.............. Tue Dec 11 20:45:45 2007Last Time Adhoc Rogue was Reported............... Tue Dec 11 20:45:45 2007Reported ByAP 1MAC Address.............................. 00:14:1b:58:4a:e0Name..................................... AP0014.1ced.2a60Radio Type............................... 802.11bSSID..................................... rf4k3apChannel.................................. 3RSSI..................................... -56 dBmSNR...................................... 15 dBEncryption............................... DisabledShortPreamble............................ DisabledWPA Support.............................. DisabledLast reported by this AP............... Tue Dec 11 20:45:45 2007Related Commands
config rogue adhoc
config rogue rule
show rogue adhoc summary
show rogue ignore-list
show rogue rule detailed
show rogue rule summaryshow rogue adhoc summary
To display a summary of the ad-hoc rogue access points detected by the Cisco wireless LAN controller, use the show rogue adhoc summary command.
show rogue adhoc summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a summary of all ad-hoc rogues:
> show rogue adhoc summaryDetect and report Ad-Hoc Networks................ EnabledClient MAC Address Adhoc BSSID State # APs Last Heard------------------ ----------- ----- --- -------xx:xx:xx:xx:xx:xx super Alert 1 Sat Aug 9 21:12:50 2004xx:xx:xx:xx:xx:xx Alert 1 Aug 9 21:12:50 2003xx:xx:xx:xx:xx:xx Alert 1 Sat Aug 9 21:10:50 2003Related Commands
config rogue adhoc
config rogue rule
show rogue adhoc detailed
show rogue ignore-list
show rogue rule detailed
show rogue rule summaryshow rogue ap clients
To display details of rogue access point clients detected by the Cisco wireless LAN controller, use the show rogue ap clients command.
show rogue ap clients ap_mac_address
Syntax Description
Defaults
None.
Examples
This example shows how to display details of rogue access point clients:
> show rogue ap clients xx:xx:xx:xx:xx:xxMAC Address State # APs Last Heard----------------- ------------------ ----- -------------------------00:bb:cd:12:ab:ff Alert 1 Fri Nov 30 11:26:23 2007Related Commands
config rogue ap classify
config rogue ap friendly
config rogue ap rldp
config rogue ap ssid
config rogue ap timeout
config rogue ap valid-client
config rogue rule
config trapflags rogueap
show rogue ap detailed
show rogue ap summary
show rogue ap friendly summary
show rogue ap malicious summary
show rogue ap unclassified summaryshow rogue ap detailed
To display details of a rogue access point detected by the Cisco wireless LAN controller, use the show rogue-ap detailed command.
show rogue ap detailed ap_mac_address
Syntax Description
Defaults
None.
Examples
This example shows how to display detailed information of a rogue access point:
> show rogue ap detailed xx:xx:xx:xx:xx:xxRogue BSSID...................................... 00:0b:85:63:d1:94Is Rogue on Wired Network........................ NoClassification................................... UnclassifiedState............................................ AlertFirst Time Rogue was Reported.................... Fri Nov 30 11:24:56 2007Last Time Rogue was Reported..................... Fri Nov 30 11:24:56 2007Reported ByAP 1MAC Address.............................. 00:12:44:bb:25:d0Name..................................... HReapRadio Type............................... 802.11gSSID..................................... edu-eapChannel.................................. 6RSSI..................................... -61 dBmSNR...................................... -1 dBEncryption............................... EnabledShortPreamble............................ EnabledWPA Support.............................. DisabledLast reported by this AP.............. Fri Nov 30 11:24:56 2007Related Commands
config rogue ap classify
config rogue ap friendly
config rogue ap rldp
config rogue ap ssid
config rogue ap timeout
config rogue ap valid-client
config rogue rule
show rogue ap clients
show rogue ap summary
show rogue ap friendly summary
show rogue ap malicious summary
show rogue ap unclassified summaryshow rogue ap summary
To display a summary of the rogue access points detected by the Cisco wireless LAN controller, use the show rogue-ap summary command.
show rogue ap summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a summary of all rogue access points:
> show rogue ap summaryRogue Location Discovery Protocol................ DisabledRogue ap timeout................................. 1200MAC Address Classification # APs # Clients Last Heard----------------- ------------------ ----- --------- -----------------------xx:xx:xx:xx:xx:xx friendly 1 0 Thu Aug 4 18:57:11 2005xx:xx:xx:xx:xx:xx malicious 1 0 Thu Aug 4 19:00:11 2005xx:xx:xx:xx:xx:xx malicious 1 0 Thu Aug 4 18:57:11 2005xx:xx:xx:xx:xx:xx malicious 1 0 Thu Aug 4 18:57:11 2005Related Commands
config rogue ap classify
config rogue ap friendly
config rogue ap rldp
config rogue ap ssid
config rogue ap timeout
config rogue ap valid-client
config rogue rule
show rogue ap clients
show rogue ap detailed
show rogue ap friendly summary
show rogue ap malicious summary
show rogue ap unclassified summaryshow rogue ap friendly summary
To display a list of the friendly rogue access points detected by the controller, use the show rogue-ap friendly summary command.
show rogue ap friendly summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a summary of all friendly rogue access points:
> show rogue ap friendly summaryNumber of APs.................................... 1MAC Address State # APs # Clients Last Heard----------------- ------------------ ----- --------- ---------------------------XX:XX:XX:XX:XX:XX Internal 1 0 Tue Nov 27 13:52:04 2007Related Commands
config rogue ap classify
config rogue ap friendly
config rogue ap rldp
config rogue ap ssid
config rogue ap timeout
config rogue ap valid-client
config rogue rule
config trapflags rogueap
show rogue ap clients
show rogue ap detailed
show rogue ap summary
show rogue ap malicious summary
show rogue ap unclassified summaryshow rogue ap malicious summary
To display a list of the malicious rogue access points detected by the controller, use the show rogue-ap malicious summary command.
show rogue ap malicious summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a summary of all malicious rogue access points:
> show rogue ap malicious summaryNumber of APs.................................... 2MAC Address State # APs # Clients Last Heard----------------- ------------------ ----- --------- ---------------------------XX:XX:XX:XX:XX:XX Alert 1 0 Tue Nov 27 13:52:04 2007XX:XX:XX:XX:XX:XX Alert 1 0 Tue Nov 27 13:52:04 2007Related Commands
config rogue ap classify
config rogue ap friendly
config rogue ap rldp
config rogue ap ssid
config rogue ap timeout
config rogue ap valid-client
config rogue rule
config trapflags rogueap
show rogue ap clients
show rogue ap detailed
show rogue ap summary
show rogue ap friendly summary
show rogue ap unclassified summaryshow rogue ap unclassified summary
To display a list of the unclassified rogue access points detected by the controller, use the show rogue-ap unclassified summary command.
show rogue ap unclassified summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a list of all unclassified rogue access points:
> show rogue ap unclassified summaryNumber of APs.................................... 164MAC Address State # APs # Clients Last Heard----------------- ------------------ ----- --------- -----------------------XX:XX:XX:XX:XX:XX Alert 1 0 Fri Nov 30 11:12:52 2007XX:XX:XX:XX:XX:XX Alert 1 0 Fri Nov 30 11:29:01 2007XX:XX:XX:XX:XX:XX Alert 1 0 Fri Nov 30 11:26:23 2007XX:XX:XX:XX:XX:XX Alert 1 0 Fri Nov 30 11:26:23 2007Related Commands
config rogue ap classify
config rogue ap friendly
config rogue ap rldp
config rogue ap ssid
config rogue ap timeout
config rogue ap valid-client
config rogue rule
config trapflags rogueap
show rogue ap clients
show rogue ap detailed
show rogue ap summary
show rogue ap friendly summary
show rogue ap malicious summaryshow rogue client detailed
To display details of a rogue client detected by a Cisco wireless LAN controller, use the show rogue client detailed command.
show rogue client detailed MAC
Syntax Description
Defaults
None.
Examples
This example shows how to display detailed information for a rogue client:
> show rogue client detailed xx:xx:xx:xx:xx:xxRogue BSSID...................................... 00:0b:85:23:ea:d1State............................................ AlertFirst Time Rogue was Reported.................... Mon Dec 3 21:50:36 2007Last Time Rogue was Reported..................... Mon Dec 3 21:50:36 2007Rogue Client IP address.......................... Not knownReported ByAP 1MAC Address.............................. 00:15:c7:82:b6:b0Name..................................... AP0016.47b2.31eaRadio Type............................... 802.11aRSSI..................................... -71 dBmSNR...................................... 23 dBChannel.................................. 149Last reported by this AP.............. Mon Dec 3 21:50:36 2007Related Commands
show rogue client summary
show rogue ignore-list
config rogue client
config rogue ruleshow rogue client summary
To display a summary of the rogue clients detected by the Cisco wireless LAN controller, use the show rogue client summary command.
show rogue client summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a list of all rogue clients:
> show rogue client summaryMAC Address State # APs Last Heard----------------- ------------------ ----- -----------------------xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:00:08 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:00:08 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:00:08 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:00:08 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:00:08 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:00:08 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:09:11 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:03:11 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:03:11 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:09:11 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 18:57:08 2005xx:xx:xx:xx:xx:xx Alert 1 Thu Aug 4 19:12:08 2005Related Commands
show rogue client detailed
show rogue ignore-list
config rogue client
config rogue ruleshow rogue ignore-list
To display a list of rogue access points that are configured to be ignored, use the show rogue ignore-list command.
show rogue ignore-list
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a list of all rogue access points that are configured to be ignored:
> show rogue ignore-listMAC Address-----------------xx:xx:xx:xx:xx:xxRelated Commands
config rogue adhoc
config rogue ap classify
config rogue ap friendly
config rogue ap rldp
config rogue ap ssid
config rogue ap timeout
config rogue ap valid-client
config rogue client
config rogue rule
config trapflags rogueap
show rogue ap clients
show rogue ap detailed
show rogue ap summary
show rogue ap friendly summary
show rogue ap malicious summary
show rogue ap unclassified summary
show rogue client detailed
show rogue client summary
show rogue ignore-list
show rogue rule detailed
show rogue rule summaryshow rogue rule detailed
To display detailed information for a specific rogue classification rule, use the show rogue rule detailed command.
show rogue rule detailed rule_name
Syntax Description
Defaults
None.
Examples
This example shows how to display detailed information on a specific rogue classification rule:
> show rogue rule detailed Rule2Priority......................................... 2Rule Name........................................ Rule2State............................................ EnabledType............................................. MaliciousMatch Operation.................................. AnyHit Count........................................ 352Total Conditions................................. 2Condition 1type......................................... Client-countvalue........................................ 10Condition 2type......................................... Durationvalue (seconds).............................. 2000Condition 3type......................................... Managed-ssidvalue........................................ EnabledCondition 4type......................................... No-encryptionvalue........................................ EnabledCondition 5type......................................... Rssivalue (dBm).................................. -50Condition 6type......................................... SsidSSID Count................................... 1SSID 1.................................... testRelated Commands
config rogue rule
show rogue ignore-list
show rogue rule summaryshow rogue rule summary
To display the rogue classification rules that are configured on the controller, use the show rogue rule summary command.
show rogue rule summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display a list of all rogue rules that are configured on the controller:
> show rogue rule summaryPriority Rule Name State Type Match Hit Count-------- ----------------------- -------- ------------- ----- ---------1 mtest Enabled Malicious All 02 asdfasdf Enabled Malicious All 0Related Commands
config rogue rule
show rogue ignore-list
show rogue rule detailedshow route summary
To display the routes assigned to the Cisco wireless LAN controller service port, use the show route summary command.
show route summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display all the configured routes:
> show route summaryNumber of Routes............................... 1Destination Network Genmask Gateway------------------- ------------------- -------------------xxx.xxx.xxx.xxx 255.255.255.0 xxx.xxx.xxx.xxxRelated Commands
config route
show rules
To display the active internal firewall rules, use the show rules command.
show rules
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display active internal firewall rules:
> show rules--------------------------------------------------------Rule ID.............: 3Ref count...........: 0Precedence..........: 99999999Flags...............: 00000001 ( PASS )Source IP range:(Local stack)Destination IP range:(Local stack)--------------------------------------------------------Rule ID.............: 25Ref count...........: 0Precedence..........: 99999999Flags...............: 00000001 ( PASS )Service InfoService name........: GDBProtocol............: 6Source port low.....: 0Source port high....: 0Dest port low.......: 1000Dest port high......: 1000Source IP range:IP High............: 0.0.0.0Interface..........: ANYDestination IP range:(Local stack)--------------------------------------------------------show run-config
To display a comprehensive view of the current Cisco wireless LAN controller configuration, use the show run-config command.
show run-config [no ap | commands]
Syntax Description
no-ap
(Optional) Excludes access point configuration settings.
commands
(Optional) Displays a list of user-configured commands on the controller.
Defaults
None.
Usage Guidelines
These commands have replaced the show running-config command.
Some WLAN controllers may have no Crypto Accelerator (VPN termination module) or power supplies listed because they have no provisions for VPN termination modules or power supplies.
The show run-config command shows only values configured by the user. It does not show system-configured default values.
Examples
This example shows how to display the current controller running configuration:
> show run-configPress Enter to continue...System InventorySwitch Description............................... Cisco ControllerMachine Model....................................Serial Number.................................... FLS0923003BBurned-in MAC Address............................ xx:xx:xx:xx:xx:xxCrypto Accelerator 1............................. AbsentCrypto Accelerator 2............................. AbsentPower Supply 1................................... AbsentPower Supply 2................................... Present, OKPress Enter to continue Or <Ctl Z> to abort...Related Commands
show serial
To display the serial (console) port configuration, use the show serial command.
show serial
Syntax Description
This command has no arguments or keywords.
Defaults
9600, 8, off, 1, none.
Examples
This example shows how to display EIA-232 parameters and the serial port inactivity timeout:
> show serialSerial Port Login Timeout (minutes)......... 45Baud Rate................................... 9600Character Size.............................. 8Flow Control:............................... DisableStop Bits................................... 1Parity Type:................................ noneRelated Commands
config serial baudrate
config serial timeoutshow sessions
To display the console port login timeout and maximum number of simultaneous command-line interface (CLI) sessions, use the show sessions command.
show sessions
Syntax Description
This command has no arguments or keywords.
Defaults
5 minutes, 5 sessions.
Examples
This example shows how to display the CLI session configuration setting:
> show sessionsCLI Login Timeout (minutes)............ 0Maximum Number of CLI Sessions......... 5The response indicates that the CLI sessions never time out and that the Cisco wireless LAN controller can host up to five simultaneous CLI sessions.
Related Commands
config sessions maxsessions
config sessions timeoutshow snmpcommunity
To display Simple Network Management Protocol (SNMP) community entries, use the show snmpcommunity command.
show snmpcommunity
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display SNMP community entries:
> show snmpcommunitySNMP Community Name Client IP Address Client IP Mask Access Mode Status------------------- ----------------- ----------------- ----------- --------public 0.0.0.0 0.0.0.0 Read Only Enable********** 0.0.0.0 0.0.0.0 Read/Write EnableRelated Commands
config snmp community accessmode
config snmp community create
config snmp community delete
config snmp community ipaddr
config snmp community mode
config snmp syscontactshow snmptrap
To display Cisco wireless LAN controller Simple Network Management Protocol (SNMP) trap receivers and their status, use the show snmptrap command.
show snmptrap
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display SNMP trap receivers and their status:
> show snmptrapSNMP Trap Receiver Name IP Address Status------------------------ ----------------- --------xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx EnableRelated Commands
config snmp trapreceiver create
config snmp trapreceiver delete
config snmp trapreceiver delete
show snmpv3user
To display Simple Network Management Protocol (SNMP) version 3 configuration, use the show snmpv3user command.
show snmpv3user
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display SNMP version 3 configuration information:
> show snmpv3userSNMP v3 username AccessMode Authentication Encryption-------------------- ----------- -------------- ----------default Read/Write HMAC-SHA CFB-AESRelated Commands
config snmp v3user create
config snmp v3user deleteshow snmpversion
To display which versions of Simple Network Management Protocol (SNMP) are enabled or disabled on your controller, use the show snmpversion command.
show snmpversion
Syntax Description
This command has no arguments or keywords.
Defaults
Enable.
Examples
This example shows how to display the SNMP v1/v2/v3 status:
> show snmpversionSNMP v1 Mode.................................. DisableSNMP v2c Mode.................................. EnableSNMP v3 Mode.................................. EnableRelated Commands
show spanningtree port
To display the Cisco wireless LAN controller spanning tree port configuration, use the show spanningtree port command.
show spanningtree port port
Syntax Description
port
Physical port number:
•
•
•
Defaults
800C, Disabled, 802.1D, 128, 100, Auto.
Usage Guidelines
When the a Cisco 4400 Series wireless LAN controller is configured for port redundancy, the Spanning Tree Protocol (STP) must be disabled for all ports on the Cisco 4400 Series Wireless LAN Controller. STP can remain enabled on the switch connected to the Cisco 4400 Series Wireless LAN Controller.
Note
Examples
This example shows how to display spanning tree values on a per port basis:
> show spanningtree port 3STP Port ID................................. 800CSTP Port State.............................. DisabledSTP Port Administrative Mode................ 802.1DSTP Port Priority........................... 128STP Port Path Cost.......................... 100STP Port Path Cost Mode..................... AutoRelated Commands
config spanningtree port mode
config spanningtree port pathcost
config spanningtree port priority
show spanningtree switch
show spanningtree switch
To display the Cisco wireless LAN controller network (DS port) spanning tree configuration, use the show spanningtree switch command.
show spanningtree switch
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Usage Guidelines
Some WLAN controllers do not support the spanning tree function.
Examples
This example shows how to display spanning tree values on a per switch basis:
> show spanningtree switchSTP Specification...................... IEEE 802.1DSTP Base MAC Address................... 00:0B:85:02:0D:20Spanning Tree Algorithm................ DisableSTP Bridge Priority.................... 32768STP Bridge Max. Age (seconds).......... 20STP Bridge Hello Time (seconds)........ 2STP Bridge Forward Delay (seconds)..... 15Related Commands
config spanningtree switch bridgepriority
config spanningtree switch forwarddelay
config spanningtree switch hellotime
config spanningtree switch maxage
config spanningtree switch mode
show stats port
To display physical port receive and transmit statistics, use the show stats port command.
show stats port {detailed port | summary port}
Syntax Description
Defaults
None.
Examples
This example shows how to display the port summary information:
> show stats port summary 1Packets Received Without Error................. 399958Packets Received With Error.................... 0Broadcast Packets Received..................... 8350Packets Transmitted Without Error.............. 106060Transmit Packets Errors........................ 0Collisions Frames.............................. 0Time Since Counters Last Cleared............... 2 day 11 hr 16 min 23 secThis example shows how to display the detailed port information:
> show stats port detailed 1PACKETS RECEIVED (OCTETS)Total Bytes...................................... 26779988164 byte pkts :91828165-127 byte pkts :354016 128-255 byte pkts :1283092256-511 byte pkts :8406 512-1023 byte pkts :30061024-1518 byte pkts :1184 1519-1530 byte pkts :0> 1530 byte pkts :2PACKETS RECEIVED SUCCESSFULLYTotal............................................ 2567987Unicast Pkts :2547844 Multicast Pkts:0 Broadcast Pkts:20143PACKETS RECEIVED WITH MAC ERRORSTotal............................................ 0Jabbers :0 Undersize :0 Alignment :0FCS Errors:0 Overruns :0RECEIVED PACKETS NOT FORWARDEDTotal............................................ 0Local Traffic Frames:0 RX Pause Frames :0Unacceptable Frames :0 VLAN Membership :0VLAN Viable Discards:0 MulticastTree Viable:0ReserveAddr Discards:0CFI Discards :0 Upstream Threshold :0PACKETS TRANSMITTED (OCTETS)Total Bytes...................................... 35383164 byte pkts :0 65-127 byte pkts :0128-255 byte pkts :0 256-511 byte pkts :0512-1023 byte pkts :0 1024-1518 byte pkts :21519-1530 byte pkts :0 Max Info :1522PACKETS TRANSMITTED SUCCESSFULLYTotal............................................ 5875Unicast Pkts :5868 Multicast Pkts:0 Broadcast Pkts:7TRANSMIT ERRORSTotal Errors..................................... 0FCS Error :0 TX Oversized :0 Underrun Error:0TRANSMIT DISCARDSTotal Discards................................... 0Single Coll Frames :0 Multiple Coll Frames:0Excessive Coll Frame:0 Port Membership :0VLAN Viable Discards:0PROTOCOL STATISTICSBPDUs Received :6 BPDUs Transmitted :0802.3x RX PauseFrame:0Time Since Counters Last Cleared............... 2 day 0 hr 39 min 59 secRelated Commands
config port adminmode
config port autoneg
config port linktrap
config port power
config port linktrapshow stats switch
To display the network (DS port) receive and transmit statistics, use the show stats switch command.
show stats switch {detailed | summary}
Syntax Description
Defaults
None.
Examples
This example shows how to display switch summary statistics:
> show stats switch summaryPackets Received Without Error................. 136410Broadcast Packets Received..................... 18805Packets Received With Error.................... 0Packets Transmitted Without Error.............. 78002Broadcast Packets Transmitted.................. 3340Transmit Packet Errors......................... 2Address Entries Currently In Use............... 26VLAN Entries Currently In Use.................. 1Time Since Counters Last Cleared............... 2 day 11 hr 22 min 17 secThis example shows how to display detailed switch statistics:
> show stats switch detailedRECEIVEOctets........................................... 19351718Total Pkts....................................... 183468Unicast Pkts..................................... 180230Multicast Pkts................................... 3219Broadcast Pkts................................... 19Pkts Discarded................................... 0TRANSMITOctets........................................... 354251Total Pkts....................................... 5882Unicast Pkts..................................... 5875Multicast Pkts................................... 0Broadcast Pkts................................... 7Pkts Discarded................................... 0ADDRESS ENTRIESMost Ever Used................................... 1Currently In Use................................. 1VLAN ENTRIESMaximum.......................................... 128Most Ever Used................................... 1Static In Use.................................... 1Dynamic In Use................................... 0VLANs Deleted.................................... 0Time Since Ctrs Last Cleared..................... 2 day 0 hr 43 min 22 secRelated Commands
config switchconfig mode
config switchconfig secret-obfuscation
show switchconfigshow switchconfig
To display parameters that apply to the Cisco wireless LAN controller, use the show switchconfig command.
show switchconfig
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display parameters that apply to the Cisco wireless LAN controller:
> show switchconfig802.3x Flow Control Mode......................... DisableCurrent LWAPP Transport Mode..................... Layer 3LWAPP Transport Mode after next switch reboot.... Layer 3Related Commands
config switchconfig mode
config switchconfig secret-obfuscation
show stats switchshow sysinfo
To display high-level Cisco wireless LAN controller information, use the show sysinfo command.
show sysinfo
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display wireless LAN controller information:
> show sysinfoManufacturer's Name.............................. Cisco Systems Inc.Product Name..................................... Cisco ControllerProduct Version.................................. 6.0.133.0Build Information................................ Tue Mar 31 11:44:12 PDT 2009Bootloader Version............................... 0.14.0Field Recovery Image Version..................... 5.3.38.0-BL-9-16Firmware Version................................. FPGA 1.0, Env 0.8, USB console 1.27Build Type....................................... DATA + WPSSystem Name...................................... 5500System Location..................................System Contact...................................System ObjectID.................................. 1.3.6.1.4.1.9.1.1IP Address....................................... 10.10.10.7Last Reset....................................... Software resetSystem Up Time................................... 1 days 15 hrs 17 mins 48 secsSystem Timezone Location....................Current Boot License Level....................... wplusCurrent Boot License Type........................ PermanentNext Boot License Level.......................... wplusNext Boot License Type........................... PermanentConfigured Country............................... US - United StatesOperating Environment............................ Commercial (0 to 40 C)Internal Temp Alarm Limits....................... 0 to 65 CInternal Temperature............................. +45 CExternal Temperature............................. +29 CFan Status....................................... OKState of 802.11b Network......................... EnabledState of 802.11a Network......................... DisabledNumber of WLANs.................................. 183rd Party Access Point Support................... DisabledNumber of Active Clients......................... 1Burned-in MAC Address............................ 00:00:1B:EE:12:E0Power Supply 1................................... Not AvailablePower Supply 2................................... Not AvailableMaximum number of APs supported.................. 250Related Commands
Show TACACS Commands
Use the show tacacs commands to display Terminal Access Controller Access Control System (TACACS) protocol settings and statistics.
show tacacs acct statistics
To display detailed radio frequency identification (RFID) information for a specified tag, use this command:
show tacacs acct statistics
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display detailed RFID information:
> show tacacs acct statisticsAccounting Servers:Server Index..................................... 1Server Address................................... 10.0.0.0Msg Round Trip Time.............................. 0 (1/100 second)First Requests................................... 1Retry Requests................................... 0Accounting Response.............................. 0Accounting Request Success....................... 0Accounting Request Failure....................... 0Malformed Msgs................................... 0Bad Authenticator Msgs........................... 0Pending Requests................................. -1Timeout Requests................................. 1Unknowntype Msgs................................. 0Other Drops...................................... 0Related Commands
config tacacs acct
config tacacs acct
config tacacs athr
config tacacs auth
show tacacs summary
show tacacs summaryshow tacacs athr statistics
To display TACACS+ server authorization statistics, use the show tacacs athr statistics command.
show tacacs athr statistics
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display TACACS server authorization statistics:
> show tacacs athr statisticsAuthorization Servers:Server Index..................................... 3Server Address................................... 10.0.0.3Msg Round Trip Time.............................. 0 (1/100 second)First Requests................................... 0Retry Requests................................... 0Received Responses............................... 0Authorization Success............................ 0Authorization Failure............................ 0Challenge Responses.............................. 0Malformed Msgs................................... 0Bad Authenticator Msgs........................... 0Pending Requests................................. 0Timeout Requests................................. 0Unknowntype Msgs................................. 0Other Drops...................................... 0Related Commands
config tacacs acct
config tacacs acct
config tacacs athr
config tacacs auth
show tacacs summary
show tacacs auth statistics
show tacacs summaryshow tacacs auth statistics
To display TACACS+ server authentication statistics, use the show tacacs auth statistics command.
show tacacs auth statistics
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display TACACS server authentication statistics:
> show tacacs auth statisticsAuthentication Servers:Server Index..................................... 2Server Address................................... 10.0.0.2Msg Round Trip Time.............................. 0 (msec)First Requests................................... 0Retry Requests................................... 0Accept Responses................................. 0Reject Responses................................. 0Error Responses.................................. 0Restart Responses................................ 0Follow Responses................................. 0GetData Responses................................ 0Encrypt no secret Responses...................... 0Challenge Responses.............................. 0Malformed Msgs................................... 0Bad Authenticator Msgs........................... 0Pending Requests................................. 0Timeout Requests................................. 0Unknowntype Msgs................................. 0Other Drops...................................... 0Related Commands
config tacacs acct
config tacacs acct
config tacacs athr
config tacacs auth
show tacacs summary
show tacacs summaryshow tacacs summary
To display TACACS+ server summary information, use the show tacacs summary command.
show tacacs summary
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display TACACS server summary information:
> show tacacs summaryAuthentication ServersIdx Server Address Port State Tout--- ---------------- ------ -------- ----2 10.0.0.2 6 Enabled 30Accounting ServersIdx Server Address Port State Tout--- ---------------- ------ -------- ----1 10.0.0.0 10 Enabled 2Authorization ServersIdx Server Address Port State Tout--- ---------------- ------ -------- ----3 10.0.0.3 4 Enabled 2...Related Commands
config tacacs acct
config tacacs acct
config tacacs athr
config tacacs auth
show tacacs summary
show tacacs athr statistics
show tacacs auth statisticsshow tech-support
To display Cisco wireless LAN controller variables frequently requested by Cisco Technical Assistance Center (TAC), use the show tech-support command.
show tech-support
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display system resource information:
> show tech-supportCurrent CPU Load................................. 0%System BuffersMax Free Buffers.............................. 4608Free Buffers.................................. 4604Buffers In Use................................ 4Web Server ResourcesDescriptors Allocated......................... 152Descriptors Used.............................. 3Segments Allocated............................ 152Segments Used................................. 3System ResourcesUptime........................................ 747040 SecsTotal Ram..................................... 127552 KbytesFree Ram...................................... 19540 KbytesShared Ram.................................... 0 KbytesBuffer Ram.................................... 460 Kbytesshow time
To display the Cisco wireless LAN controller time and date, use the show time command.
show time
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the controller time and date:
> show timeTime............................................. Thu Aug 4 19:51:49 2005Timezone delta................................... 0:0Daylight savings................................. disabledNTP ServersNTP Polling Interval......................... 86400Index NTP Server------- --------------------------------Related Commands
config time manual
config time ntp
config time timezone
config time timezone location
config time timezone locationshow trapflags
To display the Cisco wireless LAN controller Simple Network Management Protocol (SNMP) trap flags, use the show trapflags command.
show trapflags
Syntax Description
This command has no arguments and keywords.
Defaults
None.
Examples
This example shows how to display controller SNMP trap flags:
> show trapflagsAuthentication Flag............................ EnableLink Up/Down Flag.............................. EnableMultiple Users Flag............................ EnableSpanning Tree Flag............................. EnableClient Related Traps802.11 Disassociation......................... Disable802.11 Deauthenticate......................... Disable802.11 Authenticate Failure................... Disable802.11 Association Failure.................... DisableExcluded...................................... Disable802.11 Security related trapsWEP Decrypt Error............................. EnableCisco APRegister...................................... EnableInterfaceUp................................... EnableAuto-RF ProfilesLoad.......................................... EnableNoise......................................... EnableInterference.................................. EnableCoverage...................................... EnableAuto-RF Thresholdstx-power...................................... Enablechannel....................................... Enableantenna....................................... EnableAAAauth.......................................... Enableservers....................................... Enablerogueap........................................ Enablewps............................................ Enableconfigsave..................................... EnableIP Securityesp-auth...................................... Enableesp-replay.................................... EnableinvalidSPI.................................... Enableike-neg....................................... Enablesuite-neg..................................... Enableinvalid-cookie................................ EnableRelated Commands
config trapflags 802.11-Security
config trapflags aaa
config trapflags ap
config trapflags authentication
config trapflags client
config trapflags configsave
config trapflags IPsec
config trapflags linkmode
show traplog
To display the Cisco wireless LAN controller Simple Network Management Protocol (SNMP) trap log, use the show traplog command.
show traplog
Syntax Description
This command has no arguments and keywords.
Defaults
None.
Examples
This example shows how to display controller SNMP trap log settings:
> show traplogNumber of Traps Since Last Reset........... 2447Number of Traps Since Log Last Displayed... 2447Log System Time Trap--- ------------------------ -------------------------------------------------0 Thu Aug 4 19:54:14 2005 Rogue AP : 00:0b:85:52:62:fe detected on Base Radio MAC : 00:0b:85:18:b6:50 Interface no:1(802.11b/g) with RSSI: -78 and SNR: 101 Thu Aug 4 19:54:14 2005 Rogue AP : 00:0b:85:52:19:d8 detected on Base Radio MAC : 00:0b:85:18:b6:50 Interface no:1(802.11b/g) with RSSI: -72 and SNR: 162 Thu Aug 4 19:54:14 2005 Rogue AP : 00:0b:85:26:a1:8d detected on Base Radio MAC : 00:0b:85:18:b6:50 Interface no:1(802.11b/g) with RSSI: -82 and SNR: 63 Thu Aug 4 19:54:14 2005 Rogue AP : 00:0b:85:14:b3:4f detected on Base Radio MAC : 00:0b:85:18:b6:50 Interface no:1(802.11b/g) with RSSI: -56 and SNR: 30Would you like to display more entries? (y/n)Related Commands
show version
To display access point's software information, use the show version command.
show version
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Usage Guidelines
You can only use this command from the access point console port when not connected to a controller.
Examples
This example shows how to display the access point version number:
AP# show versionCisco IOS Software, C1240 Software (C1240-K9W8-M), Experimental Version 12.3(20060829:081904) [BLD-wnbu_a10_temp_060823.daily 163] Copyright (c) 1986-2006 by Cisco Systems, Inc. Compiled Wed 30-Aug-06 03:03 byROM: Bootstrap program is C1240 boot loader BOOTLDR: C1240 Boot Loader (C1240-BOOT-M) Version 12.3(7)JA1, RELEASE SOFTWARE (fc1)Ap1242-2 uptime is 4 minutes System returned to ROM by power-on System image file is "flash:/c1240-k9w8-mx.wnbu_a10_temp_060823.20060830d/c1240-k9w8-"cisco AIR-LAP1242AG-A-K9 processor (revision B0) with 24566K/8192K bytes of memory. Processor board ID FTX0944B00B PowerPCElvis CPU at 266Mhz, revision number 0x0950 Last reset from power-on LWAPP image version 4.1.69.0 1 FastEthernet interface 2 802.11 Radio(s)32K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address: 00:14:1C:ED:47:14 Part Number : 73-9925-03 PCA Assembly Number : 800-26579-03 PCA Revision Number : A0 PCB Serial Number : FOC09351E0U Top Assembly Part Number : 800-26804-01 Top Assembly Serial Number : FTX0944B00B Top Revision Number : A0 Product/Model Number : AIR-LAP1242AG-A-K9Configuration register is 0xFshow watchlist
To display the client watchlist, use the show watchlist command.
show watchlist
Syntax Description
This command has no arguments or keywords.
Defaults
None.
Examples
This example shows how to display the client watchlist information:
> show watchlistclient watchlist state is disabledRelated Commands
config watchlist add
config watchlist delete
config watchlist disable
config watchlist enableshow wlan
To display configuration information for a specified wireless LAN or a foreign access point, or to display wireless LAN summary information, use the show wlan command.
show wlan {apgroups | summary | wlan_id | foreignAp}
Syntax Description
Defaults
None.
Examples
This example shows how to display a summary of wireless LANs for wlan_id 1:
> show wlan 1WLAN Identifier.................................. 1Profile Name..................................... wlanNetwork Name (SSID).............................. wlanStatus........................................... EnabledMAC Filtering.................................... DisabledBroadcast SSID................................... EnabledAAA Policy Override.............................. DisabledNetwork Admission ControlNAC-State...................................... EnabledQuarantine VLAN................................ 110Number of Active Clients......................... 0Exclusionlist Timeout............................ 60 secondsSession Timeout.................................. 1800 secondsCHD per WLAN..................................... EnabledWebauth DHCP exclusion........................... DisabledInterface........................................ managementWLAN ACL......................................... unconfiguredDHCP Server...................................... DefaultDHCP Address Assignment Required................. DisabledQuality of Service............................... Silver (best effort)WMM.............................................. AllowedCCX - AironetIe Support.......................... EnabledCCX - Gratuitous ProbeResponse (GPR)............. DisabledCCX - Diagnostics Channel Capability............. DisabledDot11-Phone Mode (7920).......................... DisabledWired Protocol................................... NoneIPv6 Support..................................... DisabledPassive Client Feature........................... EnabledPeer-to-Peer Blocking Action..................... DisabledRadio Policy..................................... AllDTIM period for 802.11a radio.................... 1DTIM period for 802.11b radio.................... 1Local EAP Authentication......................... DisabledSecurity802.11 Authentication:........................ Open SystemStatic WEP Keys............................... Disabled802.1X........................................ DisabledWi-Fi Protected Access (WPA/WPA2)............. EnabledWPA (SSN IE)............................... DisabledWPA2 (RSN IE).............................. EnabledTKIP Cipher............................. DisabledAES Cipher.............................. EnabledAuth Key Management802.1x.................................. EnabledPSK..................................... DisabledCCKM.................................... DisabledFT(802.11r)............................. DisabledFT-PSK(802.11r)......................... DisabledFT Reassociation Timeout......................... 20FT Over-The-Air mode............................. EnabledFT Over-The-Ds mode.............................. EnabledCKIP ......................................... DisabledIP Security................................... DisabledIP Security Passthru.......................... DisabledWeb Based Authentication...................... Disabled
