Downloads |
Table Of Contents
Installing ONS 15454 SDH E3-12 Cards
Verify Successful Turn Up of the E3-12 Card
Reset an Electrical Card (E1-N-14, DS3iN-12, or E3-12)
Replace an In-Service Electrical Card (E1-N-14, DS3iN-12, or E3-12)
Obtaining Technical Assistance
Installing ONS 15454 SDH E3-12 Cards
Product Name: 15454E-E3-12=
This document contains a description of E3-12 card features, installation procedures, removal instructions, and technical specifications. Use this document in conjunction with the Cisco ONS 15454 SDH Installation and Operations Guide and the Cisco ONS 15454 SDH Troubleshooting and Reference Guide when working with E3-12 cards.
This document contains the following sections:
•
"E3-12 Specifications" section
•
•
•
•
This document contains the following procedures:
"Installation Procedures" procedure
"Verify Successful Turn Up of the E3-12 Card" procedure
"Removal Procedures" procedure
"Reset an Electrical Card (E1-N-14, DS3iN-12, or E3-12)" procedure
Note
E3-12 Card
The twelve-port ONS 15454 SDH E3-12 card provides twelve ITU-compliant, G.703 E-3 ports per card. Each interface operates at 34.368 MBits/s (Mbps) over a 75 ohms coaxial cable (with FMEC-E3/DS3). The E3-12 card operates as a working or protect card in 1:1 protection schemes and as a working card in 1:N protection schemes. Figure 1 shows the E3-12 faceplates, and Figure 2 shows a block diagram of the card.
Figure 1 E3-12 faceplate
You can install the E3-12 card in any multispeed or high-speed card slot on the ONS 15454 SDH. Each E3-12 port features ITU-T G.703 compliant level outputs supporting cable losses of up to 12 dB @ 17184 kHz.
The E3-12 card supports 1:1 protection.
Note
Note
E3-12 Card-Level Indicators
The E3-12 card faceplate has three LEDs.
E3-12 Port-Level Indicators
You can find the status of the twelve E3-12 card ports using the LCD screen on the ONS 15454 SDH fan tray assembly. Use the LCD to view the status of any port or card slot; the screen displays the number and severity of alarms for a given port or slot. Refer to Chapter 1, "Alarm Troubleshooting," of the "Cisco ONS 15454 SDH Troubleshooting and Maintenance Guide, R3.3" for a complete description of the alarm messages.
Figure 2 E3-12 block diagram
E3-12 Specifications
•
–
–
–
–
–
–
•
–
–
–
–
–
–
–
–
–
•
–
•
–
–
–
–
•
–
–
–
–
–
•
ONS15454 SDH cards, when installed in a system, comply with these standards:–
Installation Procedures
Use this section if you are installing or removing the E3-12 card for the first time. After you become familiar with ONS 15454 SDH card installation and boot up, use this section as a reference.
Caution
Caution
Step 1
Step 2
Step 3
Figure 3 Installing cards in an ONS 15454 SDH
Card Turn Up
Follow the steps in this section to verify card turn up. If one or more of the Cisco Transport Controller (CTC) software screen conditions according to "Verify Successful Turn Up of the E3-12 Card" section are not met, re-install the card. Replace the unit if the faulty state persists.
Verify Successful Turn Up of the E3-12 Card
Step 1
Step 2
Step 3
Step 4
Step 5
Removal Procedures
Use this section if you are installing or removing the E3-12 card for the first time. After you become familiar with ONS 15454 SDH card installation and boot up, use this section as a reference.
Caution
Caution
Note
Reset an Electrical Card (E1-N-14, DS3iN-12, or E3-12)
Note
The cards should be replaced when the red FAIL LED appears.
Take these precautions before performing an electical card reset to avoid causing a linear 1:1, 1:N or MSSPRing protection switch:
Step 1
Step 2
Step 3
<------East [Node A] West------East [Node B] West------East [Node C] West------>
In a 1:1 protection scheme, place a lockout on the protect card and verify that traffic is traveling over the working span before setting the lockout.
Replace an In-Service Electrical Card (E1-N-14, DS3iN-12, or E3-12)
Step 1
Note
Step 2
a.
b.
c.
Note
Step 3
Step 4
Related Documentation
•
•
Obtaining Documentation
The following sections explain how to obtain documentation from Cisco Systems.
World Wide Web
You can access the most current Cisco documentation on the World Wide Web at the following URL:
Translated documentation is available at the following URL:
http://www.cisco.com/public/countries_languages.shtml
Documentation CD-ROM
Cisco documentation and additional literature are available in a Cisco Documentation CD-ROM package, which is shipped with your product. The Documentation CD-ROM is updated monthly and may be more current than printed documentation. The CD-ROM package is available as a single unit or through an annual subscription.
Ordering Documentation
Cisco documentation is available in the following ways:
•
http://www.cisco.com/public/ordsum.html
•
http://www.cisco.com/go/subscription
•
Documentation Feedback
If you are reading Cisco product documentation on Cisco.com, you can submit technical comments electronically. Click Leave Feedback at the bottom of the Cisco Documentation home page. After you complete the form, print it out and fax it to Cisco at 408 527-0730.
You can e-mail your comments to bug-doc@cisco.com.
To submit your comments by mail, use the response card behind the front cover of your document, or write to the following address:
Cisco Systems
Attn: Document Resource Connection
170 West Tasman Drive
San Jose, CA 95134-9883We appreciate your comments.
Obtaining Technical Assistance
Cisco provides Cisco.com as a starting point for all technical assistance. Customers and partners can obtain documentation, troubleshooting tips, and sample configurations from online tools by using the Cisco Technical Assistance Center (TAC) Web Site. Cisco.com registered users have complete access to the technical support resources on the Cisco TAC Web Site.
Cisco.com
Cisco.com is the foundation of a suite of interactive, networked services that provides immediate, open access to Cisco information, networking solutions, services, programs, and resources at any time, from anywhere in the world.
Cisco.com is a highly integrated Internet application and a powerful, easy-to-use tool that provides a broad range of features and services to help you to
•
•
•
•
•
You can self-register on Cisco.com to obtain customized information and service. To access Cisco.com, go to the following URL:
Technical Assistance Center
The Cisco TAC is available to all customers who need technical assistance with a Cisco product, technology, or solution. Two types of support are available through the Cisco TAC: the Cisco TAC Web Site and the Cisco TAC Escalation Center.
Inquiries to Cisco TAC are categorized according to the urgency of the issue:
•
•
•
•
Which Cisco TAC resource you choose is based on the priority of the problem and the conditions of service contracts, when applicable.
Cisco TAC Web Site
The Cisco TAC Web Site allows you to resolve P3 and P4 issues yourself, saving both cost and time. The site provides around-the-clock access to online tools, knowledge bases, and software. To access the Cisco TAC Web Site, go to the following URL:
All customers, partners, and resellers who have a valid Cisco services contract have complete access to the technical support resources on the Cisco TAC Web Site. The Cisco TAC Web Site requires a Cisco.com login ID and password. If you have a valid service contract but do not have a login ID or password, go to the following URL to register:
http://www.cisco.com/register/
If you cannot resolve your technical issues by using the Cisco TAC Web Site, and you are a Cisco.com registered user, you can open a case online by using the TAC Case Open tool at the following URL:
http://www.cisco.com/tac/caseopen
If you have Internet access, it is recommended that you open P3 and P4 cases through the Cisco TAC Web Site.
Cisco TAC Escalation Center
The Cisco TAC Escalation Center addresses issues that are classified as priority level 1 or priority level 2; these classifications are assigned when severe network degradation significantly impacts business operations. When you contact the TAC Escalation Center with a P1 or P2 problem, a Cisco TAC engineer will automatically open a case.
To obtain a directory of toll-free Cisco TAC telephone numbers for your country, go to the following URL:
http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml
Before calling, please check with your network operations center to determine the level of Cisco support services to which your company is entitled; for example, SMARTnet, SMARTnet Onsite, or Network Supported Accounts (NSA). In addition, please have available your service agreement number and your product serial number.
This document is to be used in conjunction with the documents listed in the "Related Documentation" section.
Copyright © 2002, Cisco Systems, Inc.
All rights reserved.
