Cisco ONS 15400 Series

Table Of Contents

Cisco ONS 15454 SDH TL1 Command Quick Reference Guide, Release 7.0.1

MS-SPRing

Bridge and Roll

Cross Connections

DWDM

Environment

Equipment

Fault

File Transfer

Log

Network

Paths

Performance

Ports

Protection

Provisionable Patchcords

Security

Synchronization

System

Troubleshooting and Test Access

VCAT

Quick Reference

Cisco ONS 15454 SDH TL1 Command Quick Reference Guide, Release 7.0.1

---

This guide lists TL1 commands and autonomous messages by category. It includes basic descriptions and input and output formats supported by the Cisco ONS 15454 SDH, Release 7.0.1. Refer to the Cisco ONS 15454 SDH TL1 Command Guide for a complete description of TL1 commands.

TL1 commands conform to the following syntax:
a:b:c:d:e: ...z;
where:
"a" is the Command Code
"b" is the Target Identifier (TID)
"c" is the Access Identifier (AID) or the User Identifier (UID)
"d" is the Correlation Tag (CTAG)
"e: ...z;" are other positions required for various commands
The TID, AID, and CTAG route and control the TL1 command.
Other parameters provide additional information required to complete the action requested by the command.

1 MS-SPRing

Table 1 MS-SPRing 

DLT-<MOD_RING>:[<TID>]:<AID>:<CTAG>[:::]; Deletes the multiplex section-shared protection ring (MS-SPRing) of the NE.

ED-<MOD_RING>:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>],[NODEID=<NODEID>], [RVRTV=<RVRTV>],[RVTM=<RVTM>],[SRVRTV=<SRVRTV>],[SRVTM=<SRVTM>][:]; Edits the MS-SPRing attributes.

ENT-<MOD_RING>:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>],NODEID=<NODEID>, MODE=<MODE>,[RVRTV=<RVRTV>],[RVTM=<RVTM>],[SRVRTV=<SRVRTV>], [SRVTM=<SRVTM>],EASTWORK=<EASTWORK>,WESTWORK=<WESTWORK>, [EASTPROT=<EASTPROT>],[WESTPROT=<WESTPROT>]; Creates a MS-SPRing in either 2-fiber or 4-fiber type.

EX-SW-<STM_MSSPR>:[<TID>]:<AID>:<CTAG>::,[<SWITCHTYPE>],[<DIRECTION>]; Exercises the algorithm for switching from a working facility to a protection facility without actually performed a switch.

RTRV-<MOD_RING>:[<TID>]:[<AID>]:<CTAG>[::::]; Retrieves all of the MS-SPRing information of the network element (NE). Output format: SID DATE TIME M CTAG COMPLD "[<AID>]::[RINGID=<RINGID>],[NODEID=<NODEID>],[MODE=<MODE>], [RVRTV=<RVRTV>],[RVTM=<RVTM>],[SRVRTV=<SRVRTV>],[SRVTM=<SRVTM>], [EASTWORK=<EASTWORK>],[WESTWORK=<WESTWORK>],[EASTPROT=<EASTPROT>], [WESTPROT=<WESTPROT>]" ;

RTRV-TRC-<STM_MSSPR>:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the valid J1 expected trace string, received trace string, trace mode, c2 byte, VC bandwidth of the STM port only if the port has MS-SPring. Output format: SID DATE TIME M CTAG COMPLD "<AID>::[LEVEL=<LEVEL>],[EXPTRC=<EXPTRC>],[INCTRC=<INCTRC>], [TRCMODE=<TRCMODE>],[C2=<C2>]" ;

2 Bridge and Roll

Table 2 Bridge and Roll  

DLT-BULKROLL-<STM_TYPE>:[<TID>]:<FROM>:<CTAG>:::[RFROMSTART= <RFROMSTART>],[RFROMEND=<RFROMEND>],WHY=<WHY>; Cancels or completes an attempted bulk rolling operation of a facility.

DLT-ROLL-<MOD_PATH>:[<TID>]:<FROM>,<TO>:<CTAG>:::WHY=<WHY>; Cancels or completes an attempted rolling operation of a facility.

ED-BULKROLL-<STM_TYPE>:[<TID>]:<FROM>:<CTAG>:::[RFROMSTART= <RFROMSTART>],[RFROMEND=<RFROMEND>],[CMDMDE=<CMDMDE>]; Edits information about rolling traffic from one end point to another without interrupting service

ED-ROLL-<MOD_PATH>:[<TID>]:<FROM>,<TO>:<CTAG>[:::CMDMDE=<CMDMDE>]; Forces a valid signal to complete a rolling operation.

ENT-BULKROLL-<STM_TYPE>:[<TID>]:<FROM>:<CTAG>:::RTOSTART=<RTOSTART>, [RFROMSTART=<RFROMSTART>],[RFROMEND=<RFROMEND>],RMODE=<RMODE>, [CMDMDE=<CMDMDE>]; Enters information for rolling traffic from one end-point to another without interrupting service. Line level/bulk rolling only.

ENT-ROLL-<MOD_PATH>:[<TID>]:<FROM>,<TO>:<CTAG>:::RFROM=<RFROM>, RTO=<RTO>,RMODE=<RMODE>,[CMDMDE=<CMDMDE>]; Enters information for rolling traffic from one end-point to another without interrupting service. Single paths only.

RTRV-BULKROLL-<STM_TYPE>:[<TID>]:<SRC>:<CTAG>; Retrieves roll data parameters on a line. Output Format: SID DATE TIME M CTAG COMPLD "<FROM>:RFROM=<RFROM>,RTO=<RTO>,[RMODE=<RMODE>],VLDSIG=<VLDSIG>" ;

RTRV-ROLL-<MOD_PATH>:[<TID>]:<SRC>:<CTAG>; Retrieves roll data parameters. ONS 15600 only. Output format: SID DATE TIME M CTAG COMPLD "<FROM>,<TO>:RFROM=<RFROM>,RTO=<RTO>,[RMODE=<RMODE>], VLDSIG=<VLDSIG>" ;

3 Cross Connections

Table 3 Cross Connections 

DLT-CRS-<PATH>:[<TID>]:<SRC>,<DST>:<CTAG>[:::CKTID=<CKTID>], [CMDMDE=<CMDMDE>]; Deletes a cross connection between virtual channel (VC) paths.

ED-CRS-<PATH>:[<TID>]:<SRC>,<DST>:<CTAG>::[<CCT>]:[ADD=<ADD>], [REMOVE=<REMOVE>],[CKTID=<CKTID>],[CMDMDE=<CMDMDE>]:<PST>[,<SST>]]; Edits the state of a VC cross-connection.

ENT-CRS-<PATH>:[<TID>]:<SRC>,<DST>:<CTAG>::[<CCT>]:[DRITYPE=<DRITYPE>], [DRINODE=<DRINODE>],[CKTID=<CKTID>],[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]]; Creates a VC cross connection with cross connection types.

RTRV-CRS:[<TID>]:[<AID>]:<CTAG>[:::CRSTYPE=<CRSTYPE>][:]; Retrieves all the cross connections based on the required PATH types. Output format: SID DATE TIME M CTAG COMPLD "<SRC>,<DST>:<CCT>,<CRSTYPE>:[DRITYPE=<DRITYPE>],[DRINODE=<SYNCSW>], [CKTID=<CKTID>]:<PSTPSTQ>,[<SSTQ>]" ;

RTRV-CRS-<PATH>:[<TID>]:<SRC>:<CTAG>[::::]; Retrieves any connections associated with the entered AID(s) or AID range; end information is returned along with the type of connection. Output format: SID DATE TIME M CTAG COMPLD "<SRC>,<DST>:<CCT>,<CRSTYPE>:[DRITYPE=<DRITYPE>],[DRINODE=<DRINODE>], [CKTID=<CKTID>]:<PSTPSTQ>,[<SSTQ>]" ;

4 DWDM

Table 4 DWDM 

DLT-FFP-<MOD2DWDMPAYLOAD>:[<TID>]:<SRC>,<DST>:<CTAG>[:::]; Deletes Y-cable protection on client facilities.

DLT-LNK:[<TID>]:<FROM>,<TO>:<CTAG>; Deletes an optical link between two optical connection points.

DLT-OCHCC:[<TID>]:<AID>:<CTAG>[:::CKTID=<CKTID>],[CMDMDE=<CMDMDE>]; Deletes the OCH client connection.

DLT-OCHNC:[<TID>]:<SRC>,<DST>:<CTAG>:::[CKTID=<CKTID>], [CMDMDE=<CMDMDE>]; Deletes the OCH network connection.

DLT-OSC:[<TID>]:<AID>:<CTAG>; Deletes the optical service channel (OSC) group of the NE.

DLT-WLEN:[<TID>]:<AID>:<CTAG>[:::CMDMDE=<CMDMDE>],[CKTID=<CKTID>]; Deletes the provisioned wavelength (WLEN).

ED-<MOD2DWDMPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[NAME=<NAME>], [CMDMDE=<CMDMDE>],[FREQ=<FREQ>],[LOSSB=<LOSSB>]:[<PST>[,<SST>]]; Edits the operating parameters for a dense wavelength division multiplexing (DWDM) client facility.

ED-APC:[<TID>]::<CTAG>[:::APCENABLE=<APCENABLE>]; Command is given to the NE to modify the amplification power control (APC) application attributes.

ED-FFP-<MOD2DWDMPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>], [RVRTV=<RVRTV>],[RVTM=<RVTM>],[PSDIRN=<PSDIRN>][:]; Edits Y-cable protection group on client facilities.

ED-FFP-OCH:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>],[RVRTV=<RVRTV>]. [RVTM=<RVTM>],[PSDIRN=<PSDIRN>][:]; Changes the provisioning for the default protection group of the DWDM port of a TXP_MR_2.5G or TXPP_MR_2.5G card.

ED-LNK:[<TID>]:<FROM>,<TO>:<CTAG>:::[CMDMDE=<CMDMDE>]: [<PST>[,<SST>]]; Edits an optical link.

ED-OCH:[<TID>]:<AID>:<CTAG>:::[RDIRN=<RDIRN>],[EXPWLEN=<EXPWLEN>], [VOAATTN=<VOAATTN>],[VOAPWR=<VOAPWR>],[CALOPWR=<CALOPWR>], [CHPOWER=<CHPOWER>],[NAME=<PORTNAME>],[SFBER=<SFBER>],[SDBER=<SDBER>], [COMM=<COMM>],[GCCRATE=<GCCRATE>],[OSDBER=<OSDBER>],[DWRAP=<DWRAP>], [FEC=<FEC>],[PAYLOADMAP=<PAYLOADMAP>],[MACADDR=<MACADDR>], [SYNCMSG=<SYNCMSG>],[SENDDUS=<SENDDUS>],[SOAK=<SOAK>],[OSPF=<OSPF>], [MFS=<MFS>],[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]]; Used to modify the attributes (that is, service parameters) and state of an optical channel (OCH) facility.

ED-OCHCC:[<TID>]:<AID>:<CTAG>[:::CKTID=<CKTID>], [CMDMDE=<CMDMDE>]:[<PST>[,<SST>]]; Edits the OCH client connection.

ED-OCHNC:[<TID>]:<SRC>,<DST>:<CTAG>:::[CKTID=<CKTID>], [CMDMDE=<CMDMDE>]:[<PST>[,<SST>]]; Edits the OCH network connection.

ED-OMS:[<TID>]:<AID>:<CTAG>:::[RDIRN=<RDIRN>],[EXPBAND=<EXPBAND>], [VOAATTN=<VOAATTN>],[VOAPWR=<VOAPWR>],[CALOPWR=<CALOPWR>], [CHPOWER=<CHPOWER>],[NAME=<NAME>],[SOAK=<SOAK>], [CMDMDE=<CMDMDE>]:[<PST>[,<SST>]]; Used to modify the attributes (that is, service parameters) and state of an optical multiplex section (OMS) facility.

ED-OSC:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>],[NODEID=<NODEID>]; Edits the OSC group attributes.

ED-OTS:[<TID>]:<AID>:<CTAG>:::[RDIRN=<RDIRN>],[VOAATTN=<VOAATTN>], [VOAPWR=<VOAPWR>],[OFFSET=<OFFSET>],[CALTILT=<CALTILT>],[OSRI=<OSRI>], [AMPLMODE=<AMPLMODE>],[CHPOWER=<CHPOWER>],[EXPGAIN=<EXPGAIN>], [NAME=<NAME>],[SOAK=<SOAK>],[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]]; Modifies the attributes (that is, service parameters) and state of an optical transport section (OTS) facility.

ED-SLV-WDMANS:[<TID>]:<AID>:<CTAG>:::[HIGHSLVEXP=<HIGHSLVEXP>], [LOWSLVEXP=<LOWSLVEXP>]; Provisions the expected span loss verification.

ED-TRC-OCH:[<TID>]:<SRC>:<CTAG>:::[EXPTRC=<EXPTRC>],[TRC=<TRC>], [TRCMODE=<TRCMODE>],[TRCLEVEL=<TRCLEVEL>],[TRCFORMAT=<TRCFORMAT>][:]; Edits trace-related optical channel facilities.

ED-WDMANS:[<TID>]:<AID>:<CTAG>:::[POWERIN=<POWERIN>], [POWEROUT=<POWEROUT>],[POWEREXP=<POWEREXP>],[NTWTYPE=<NTWTYPE>]; Modifies the automatic optical node setup (AONS) application attributes.

ED-WLEN:[<TID>]:<AID>:<CTAG>:::[SIZE=<SIZE>],[CKTID=<CKTID>], [CMDMDE=<CMDMDE>]:[<PST>[,<SST>]]; Edits wavelength provisioning.

ENT-FFP-<MOD2DWDMPAYLOAD>:[<TID>]:<SRC>, <DST>:<CTAG>:::[PROTTYPE=<PROTTYPE>],[PROTID=<PROTID>],[RVRTV=<RVRTV>], [RVTM=<RVTM>],[PSDIRN=<PSDIRN>][:]; Creates Y-cable protection on client facilities.

ENT-LNK:[<TID>]:<FROM>,<TO>:<CTAG>::::[<PST>[,<SST>]]; Creates an optical link between two optical connection points.

ENT-OCHCC:[<TID>]:<AID>:<CTAG>[:::CKTID=<CKTID>], [CMDMDE=<CMDMDE>]:[<PST>][,<SST>]; Allocates an OCH client connection.

ENT-OCHNC:[<TID>]:<SRC>,<DST>:<CTAG>::[<WCT>]:[CKTID=<CKTID>], [CMDMDE=<CMDMDE>]:[<PST>[,<SST>]]; Allocates an OCH network connection.

ENT-OSC:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>],[NODEID=<NODEID>], [EAST=<EAST>],[WEST=<WEST>]; Creates the OSC group of the NE.

ENT-WLEN:[<TID>]:<AID>:<CTAG>::[<CCT>]:[SIZE=<SIZE>], [CKTID=<CKTID>]:[<PST>[,<SST>]]; Allocates a wavelength.

OPR-APC:[<TID>]::<CTAG>[::::]; Permit the NE's APC application to force regulation of the optical power to the DWDM ring.

OPR-LASER-OTS:[<TID>]:<AID>:<CTAG>; Instructs a laser to be switched on.

OPR-LNK:[<TID>]::<CTAG>; Permits the NE's optical link (OLNK) application to calculate all automatic optical links between points that can be univocally identified by the NE.

OPR-PROTNSW-OCH:[<TID>]:<AID>:<CTAG>::<SW>; Performs a protection switch on the trunk port of a TXPP_MR_2.5G transponder (protect version only).

OPR-SLV-WDMANS:[<TID>]:<AID>:<CTAG>; Invokes the calculation of the expected span loss verification.

OPR-WDMANS:[<TID>]::<CTAG>; Permits the NE's AONS application to force a recompute of the value assigned to all variable optical attenuators (VOAs) representing the optical path inside the node.

RLS-LASER-OTS:[<TID>]:<AID>:<CTAG>; Instructs a laser to be switched off.

RLS-PROTNSW-<MOD2DWDMPAYLOAD>:[<TID>]:<SRC>:<CTAG>[::]; Releases the Y-cable protection switch on client facilities.

RLS-PROTNSW-OCH:[<TID>]:<AID>:<CTAG>; Releases the protection switch on a TXPP_MR_2.5G transponder trunk port (protect version only).

RTRV-<MOD2DWDMPAYLOAD>:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the configuration parameter of a DWDM client. Output format: SID DATE TIME M CTAG COMPLD "<AIDUNIONID>,<AIDTYPE>:,,[<ROLE>],[<STATUS>]:[NAME=<NAME>],[LBCL=<LBCL>], [OPT=<OPT>],[OPR=<OPR>],[FREQ=<FREQ>],[LOSSB=<LOSSB>]:<PSTPSTQ>,[<SST>]" ;

RTRV-ALMTH-<MOD2>:[<TID>]:<AID>:<CTAG>::[<CONDTYPE>][,,::]; Retrieves the alarm threshold values. Output format: SID DATE TIME M CTAG COMPLD "<AID>,<MOD>:<CONDTYPE>,,,<THLEVEL>" ;

RTRV-APC:[<TID>]::<CTAG>; Retrieves the NE's APC application attributes. Output format: SID DATE TIME M CTAG COMPLD "::[APCENABLE=<APCENABLE>],[APCSTATE=<APCSTATE>]" ;

RTRV-FFP-<MOD2DWDMPAYLOAD>:[<TID>]:<SRC>:<CTAG>[::::]; Retrieves Y-cable protection on client facilities. Output format: SID DATE TIME M CTAG COMPLD "<AIDUNIONID>,<AIDUNIONID1>::[PROTTYPE=<PROTTYPE>],[PROTID=<PROTID>], [RVRTV=<RVRTV>],[RVTM=<RVTM>],[PSDIRN=<PSDIRN>]" ;

RTRV-FFP-OCH:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the protection group information for the TXP_MR_2.5G or TXPP_MR_2.5G transponder trunk port. Output format: SID DATE TIME M CTAG COMPLD "<WORK>,<PROTECT>::[PROTTYPE=<PROTTYPE>],[PROTID=<PROTID>], [RVRTV=<RVRTV>],[RVTM=<RVTM>],[PSDIRN=<PSDIRN>]" ;

RTRV-LNK:[<TID>]::<CTAG>; Retrieves all the (optical) links created in the NE. Output format: SID DATE TIME M CTAG COMPLD "<FROM>,<TO>::[OLNKT=<OLNKT>],[CTYPE=<CTYPE>],[RDIRN=<RDIRN>], [BAND=<BAND>],[WLEN=<WLEN>]:<PST_PSTQ>,[<SST>]" ;

RTRV-LNK-<MOD2O>:[<TID>]:<AID>:<CTAG>:::[OLNKT=<OLNKT>],[CTYPE=<CTYPE>], [RDIRN=<RDIRN>]; Retrieves any optical link associated with the entered AID(s) or AID range. Output format: SID DATE TIME M CTAG COMPLD "<FROM>,<TO>::[OLNKT=<OPTICALLINKTYPE>],[CTYPE=<CREATIONTYPE>], [RDIRN=<RDIRN>],[BAND=<BAND>],[WLEN=<WLEN>]:<PST_PSTQ>,[<SST>]" ;

RTRV-NE-APC:[<TID>]:[<AID>]:<CTAG>; Retrieves the NE's APC application ports involved in node setup regulation. Output format: SID DATE TIME M CTAG COMPLD "<AID>,<MOD>::[MODIFDAT=<MODIFDAT>],[MODIFTM=<MODIFTM>], [CHECKDAT=<CHECKDAT>],[CHECKTM=<CHECKTM>]" ;

RTRV-NE-WDMANS:[<TID>]:[<AID>]:<CTAG>; Retrieves the NE's optical node setup (WDMANS) application ports involved in node setup regulation. Output format: SID DATE TIME M CTAG COMPLD "<AID>,<AIDTYPE>::[REGULATED=<REGULATED>],[PARAM=<PARAM>]" ;

RTRV-OCH:[<TID>]:<AID>:<CTAG>; Retrieves the attributes (that is, service parameters) and state of an OCH facility. Output format: SID DATE TIME M CTAG COMPLD "<AID>:,,[<ROLE>],[<STATUS>]:[RDIRN=<RDIRN>],[OPTYPE=<OPTICALPORTTYPE>], [OPWR=<POWER>],[EXPWLEN=<EXPWLEN>],[ACTWLEN=<ACTWLEN>], [ILOSS=<ILOSS>],[VOAMODE=<VOAMODE>],[VOAATTN=<VOAATTN>], [VOAPWR=<VOAPWR>],[VOAREFATTN=<VOAREFATTN>], [VOAREFPWR=<VOAREFPWR>],[REFOPWR=<REFOPWR>],[CALOPWR=<CALOPWR>], [CHPOWER=<CHPOWER>],[NAME=<PORTNAME>],[SFBER=<SFBER>],[SDBER=<SDBER>], [COMM=<COMM>],[GCCRATE=<GCCRATE>],[DWRAP=<DWRAP>],[FEC=<FEC>], [PAYLOADMAP=<PAYLOADMAP>],[OSFBER=<OSFBER>],[OSDBER=<OSDBER>], [MACADDR=<MACADDR>],[SYNCMSG=<SYNCMSG>],[SENDDUS=<SENDDUS>], [SOAK=<SOAK>],[SOAKLEFT=<SOAKLEFT>],[OSPF=<OSPF>],[LBCL=<LBCL>], [OPT=<OPT>],[OPR=<OPR>]:<PST_PSTQ>,[<SSTQ>]" ;

RTRV-OCHCC:[<TID>]:<AID>:<CTAG>; Retrieves the OCH client connection provisioning information. Output format: SID DATE TIME M CTAG COMPLD "<AID>::[PAYLOAD=<PAYLOAD>],[CTKID=<CTKID>]:<PSTPSTQ>" ;

RTRV-OCHNC:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the OCH wavelength connection provisioning information. Output format: SID DATE TIME M CTAG COMPLD "<SRC>,<DST>:<WCT>:[CKTID=<CKTID>]::<PSTPSTQ>" ;

RTRV-OMS:[<TID>]:<AID>:<CTAG>; Retrieves the attributes (that is, service parameters) and state of an OMS facility. Output format: SID DATE TIME M CTAG COMPLD "<AID>::RDIRN=<RDIRN>,OPTYPE=<OPTICALPORTTYPE>,[OPWR=<POWER>], EXPBAND=<EXPBAND>,[ACTBAND=<ACTBAND>],[ILOSS=<ILOSS>], [VOAMODE=<VOAMODE>],[VOAATTN=<VOAATTN>],[VOAPWR=<VOAPWR>], [VOAREFATTN=<VOAREFATTN>],[VOAREFPWR=<VOAREFPWR>], [REFOPWR=<REFOPWR>],[CALOPWR=<CALOPWR>],[CHPOWER=<CHPOWER>], [NAME=<NAME>]:<PST_PSTQ>,[<SSTQ>]" ;

RTRV-OPM:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the optical power monitoring parameters present at the OCH layer in a reconfigurable optical add/drop multiplexing (ROADM) node. Output format: SID DATE TIME M CTAG COMPLD "<AID>::[POWEROUT=<POWEROUT>],[POWERADD=<POWERADD>], [POWERPT=<POWERPT>]" ;

RTRV-OSC:[<TID>]:<AID>:<CTAG>; Retrieves all OSC information of the NE. Output format: SID DATE TIME M CTAG COMPLD "<AID>::[RINGID=<RINGID>],[NODEID=<NODEID>],[EAST=<EAST>],[WEST=<WEST>]" ;

RTRV-OTS:[<TID>]:<AID>:<CTAG>; Retrieves the attributes (that is, service parameters) and state of an OTS facility. Output format: SID DATE TIME M CTAG COMPLD "<AID>:RDIRN=<RDIRN>,OPTYPE=<OPTICALPORTTYPE>,[OPWR=<POWER>], [ILOSS=<ILOSS>],[VOAMODE=<VOAMODE>],[VOAATTN=<VOAATTN>], [VOAPWR=<VOAPWR>],[VOAREFATTN=<VOAREFATTN>], [VOAREFPWR=<VOAREFPWR>],[OSRI=<OSRI>],[AMPLMODE=<AMPLMODE>], [CHPOWER=<CHPOWER>],[GAIN=<GAIN>],[EXPGAIN=<EXPGAIN>], [REFOPWR=<REFOPWR>],[OFFSET=<OFFSET>],[REFTILT=<REFTILT>], [CALTILT=<CALTILT>],[ASEOPWR=<ASEOPWR>],[DCULOSS=<DCULOSS>], [AWGST=<AWGST>],[HEATST=<HEATST>],[NAME=<NAME>]:<PST_PSTQ>,[<SSTQ>]" ;

RTRV-PATH-OCH:[<TID>]:<AID>:<CTAG>; Retrieves the OCH path inside a node. Output format: SID DATE TIME M CTAG COMPLD "<AID>:[WLEN],[PATH]:" ;

RTRV-PROTNSW-OCH:[<TID>]:<AID>:<CTAG>; Retrieves the protection switch status of a TXPP_MR_2.5G transponder trunk port (protect version only). Output format: SID DATE TIME M CTAG COMPLD "<AID>:<SW>,<SWTYPE>" ;

RTRV-SLV-WDMANS:[<TID>]:<AID>:<CTAG>; Retrieves the options provisionable by the ED-SLV-WDMASN command. Output format: SID DATE TIME M CTAG COMPLD "<AID>::[HIGHSLVEXP=<HIGHSLVEXP>],[LOWSLVEXP=<LOWSLVEXP>], [SLVACT=<SLVACT>],[RESOLUTION=<RESOLUTION>]" ;

RTRV-TRC-OCH:[<TID>]:<SRC>:<CTAG>::[<MSGTYPE>],[<TRCLEVEL>][::]; Retrieves security trace information. Output format: SID DATE TIME M CTAG COMPLD "<CHANNEL>,<MOD>::[TRCLEVEL=<TRCLEVEL>],[EXPTRC=<EXPTRC>], [TRC=<TRC>],[INCTRC=<INCTRC>],[TRCMODE=<TRCMODE>], [TRCFORMAT=<TRCFORMAT>]" ;

RTRV-WDMANS:[<TID>]:<AID>:<CTAG>; Retrieves the AONS application attributes. Output format: SID DATE TIME M CTAG COMPLD "<AID>::[POWERIN=<POWERIN>],[POWEROUT=<POWEROUT>], [POWEREXP=<POWEREXP>],[NTWTYPE=<NTWTYPE>], [OPTICALTYPE=<OPTICALTYPE>],[LASTRUNDAT=<LASTRUNDAT>], [LASTRUNTM=<LASTRUNTM>]" ;

SET-ALMTH-<MOD2>:[<TID>]:<AID>:<CTAG>::<CONDTYPE>,<THLEV>[,,,]; Sets the alarm thresholds on the following cards/ports/channels: MXP_2.5G_10G/TXP_MR_10G, optical service channel, optical amplifier, dispersion compensation units, multiplex/demultiplex and OADM.

5 Environment

Table 5 Environment 

OPR-ACO-ALL:[<TID>]:[<AID>]:<CTAG>; Operates the cut-off of the office audible alarm indications without changing the local alarm indications.

OPR-EXT-CONT:[<TID>]:<AID>:<CTAG>::[<CONTTYPE>],[<DURATION>]; Operates an external control and closes the external control contact.

REPT ALM ENV: Reports a customer defined condition on an environmental alarm input. Output format: SID DATE TIME ** ATAG REPT ALM ENV "<AID>:<NTFCNCDE>,<ALMTYPE>,[<OCRDAT>],[<OCRTM>],[<DESC>]" ;

REPT EVT ENV: Reports a non-alarmed event against an environmental alarm input. Output format: SID DATE TIME A ATAG REPT EVT ENV "<AID>:<ALMTYPE>,[<CONDEFF>],,,,,,,:[<DESC>]" ;

RLS-EXT-CONT:[<TID>]:<AID>:<CTAG>[::,]; Releases a forced contact state to return the control of the contact to an automatic control state.

RTRV-ALM-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>]; Retrieves the environmental alarms. Output format: SID DATE TIME M CTAG COMPLD "<AID>:<NTFCNCDE>,<ALMTYPE>,[<OCRDAT>],[<OCRTM>],[<DESC>]" ;

RTRV-ATTR-CONT:[<TID>]:<AID>:<CTAG>[::<CONTTYPE>]; Retrieves attributes associated with an external control. Output format: SID DATE TIME M CTAG COMPLD "<AID>:[<CONTTYPE>]" ;

RTRV-ATTR-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>]; Retrieves attributes associated with an environmental alarm. Output format: SID DATE TIME M CTAG COMPLD "<AID>:[<NTFCNCDE>],[<ALMTYPE>],[<DESC>]" ;

RTRV-COND-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>][,,,]; Retrieves the environmental conditions. Output format: SID DATE TIME M CTAG COMPLD "<AID>:<NTFCNCDE>,<ALMTYPE>,[<OCRDAT>],[<OCRTM>],,,,[<DESC>]" ;

RTRV-EXT-CONT:[<TID>]:<AID>:<CTAG>[::<CONTTYPE>]; Instructs an NE to report the control state of an external control. Output format: SID DATE TIME M CTAG COMPLD "<AID>:[<CONTTYPE>],<DUR>,[<CONTSTATE>]" ;

SET-ATTR-CONT:[<TID>]:<AID>:<CTAG>[::<CONTTYPE>]; Sets attributes associated with an external control.

SET-ATTR-ENV:[<TID>]:<AID>:<CTAG>::<NTFCNCDE>,<ALMTYPE>,<ALMMSG>; Sets attributes associated with an external control.

6 Equipment

Table 6 Equipment 

ALW-SWTOPROTN-EQPT:[<TID>]:<AID>:<CTAG>[::<DIRN>]; Allows automatic or manual switching of an equipment unit back to a protection status.

ALW-SWTOWKG-EQPT:[<TID>]:<AID>:<CTAG>[::<DIRN>]; Allows automatic or manual switching of an equipment unit back to a working status.

DLT-EQPT:[<TID>]:<AID>:<CTAG>[:::]; Deletes a card from the NE. Deletes a shelf that is no longer used.

ED-EQPT:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>],[PRTYPE=<PRTYPE>], [RVRTV=<RVRTV>],[RVTM=<RVTM>],[CMDMDE=<CMDMDE>], [CARDMODE=<CARDMODE>],[PEERID=<PEERID>],[REGENNAME=<REGENNAME>], [PWL=<PWL>],[RETIME=<RETIME>],[SHELFROLE=<SHELFROLE>], [NEWSHELFID=<NEWSHELFID>]:[<PST>[,<SST>]]; Edits the attributes for a given equipment slot in the NE. Modifies a shelf role from NC to SC on an NE configured in multi-shelf mode.

ENT-EQPT:[<TID>]:<AID>:<CTAG>::<AIDTYPE>:[PROTID=<PROTID>], [PRTYPE=<PRTYPE>],[RVRTV=<RVRTV>],[RVTM=<RVTM>], [CARDMODE=<CARDMODE>],[PEERID=<PEERID>],[REGENNAME=<REGENNAME>], [CMDMDE=<CMDMDE>],[TRANSMODE=<TRANSMODE>],[RETIME=<RETIME>], [SHELFROLE=<SHELFROLE>][:]; Enters the card type and attributes for a given equipment slot in the NE. Pre-provisions an NE configured in multi-shelf mode.

INH-SWDX-EQPT:[<TID>]:<AID>:<CTAG>[::]; Inhibits the automatic or manual switching on an NE containing duplex equipment.

INH-SWTOPROTN-EQPT:[<TID>]:<AID>:<CTAG>[::<DIRN>]; Inhibits automatic or manual switching of an equipment unit to protection.

INH-SWTOWKG-EQPT:[<TID>]:<AID>:<CTAG>[::<DIRN>]; Inhibits automatic or manual switching of an equipment unit back to the working unit.

REPT ALM EQPT Reports an alarm condition against an equipment unit or slot. Output format: SID DATE TIME ** ATAG REPT ALM EQPT "<AID>:<NTFCNCDE>,<CONDITION>,<SRVEFF>,[<OCRDAT>], [<OCRTM>],,:[<DESC>],[<AIDDET>" ;

REPT EVT EQPT Reports the occurrence of a non-alarmed event against an equipment unit or slot. Output format: SID DATE TIME A ATAG REPT EVT EQPT "<AID>:<CONDTYPE>,[<CONDEFF>],,,,,,,:[<DESC>],[<AIDDET>]" ;

RMV-EQPT:[<TID>]:<AID>:<CTAG>[::]; Removes equipment from the In Service state and places it into the Maintenance state.

RST-EQPT:[<TID>]:<AID>:<CTAG>[::]; Provisions equipment In Service. It is applicable only to equipment in transition from the Maintenance State to the In Service State.

RTRV-ALM-EQPT:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>], [<SRVEFF>][,,,]; Retrieves and sends the current status of alarm conditions associated with the equipment units. Output format: SID DATE TIME M CTAG COMPLD "[<AID>],[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>], [<OCRTM>],,:[<DESC>]" ;

RTRV-ALMTH-EQPT:[<TID>]:[<AID>]:<CTAG>::[<CONDTYPE>][,,::]; Retrieves the alarm thresholds for the power level monitoring. Output format: SID DATE TIME M CTAG COMPLD "[<AID>],<MOD2B>:<CONDTYPE>,,,<DNFIELD>" ;

RTRV-COND-EQPT:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,]; Retrieves the equipment conditions. Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>], [<OCRTM>],,,[<DESC>]" ;

RTRV-EQPT:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the data parameters and state parameters associated with an equipment unit. Also retrieves shelf parameters. Output format: SID DATE TIME M CTAG COMPLD "<AID>:<AIDTYPE>,<EQUIP>,[<ROLE>],[<STATUS>]:[PROTID=<PROTID>], [PRTYPE=<PRTYPE>],[RVRTV=<RVRTV>],[RVTM=<RVTM>], [CARDNAME=<CARDNAME>],[IOSCFG=<IOSCFG>],[CARDMODE=<CARDMODE>], [PEERID=<PEERID>],[REGENNAME=<REGENNAME>,][TRANSMODE=<TRANSMODE>], [RETIME=<RETIME>],[SHELFROLE=<SHELFROLE>]:[<PST_PSTQ>],[<SSTQ>]" ;

SET-ALMTH-EQPT:[<TID>]:[<AID>]:<CTAG>::<CONDTYPE>,<THLEV>[,,,]; Set the alarm threshold to manage the power level monitoring.

SW-DX-EQPT:[<TID>]:<SRC>:<CTAG>::[<MODE>][,]; Switches a cross-connect card with the mate card within the NE.

SW-TOPROTN-EQPT:[<TID>]:<AID>:<CTAG>::[<MODE>],[<PROTID>],[<DIRN>]; Performs an equipment unit protection switch.

SW-TOWKG-EQPT:[<TID>]:<AID>:<CTAG>::[<MODE>],[<DIRN>]; Switches the protected working unit back to the working unit.

7 Fault

Table 7 Fault 

REPT ALM <MOD2ALM> Reports an alarm condition against a facility or a path. Output format: SID DATE TIME ** ATAG REPT ALM <MOD2ALM> "<AID>:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>], [<OCRTM>],,:[<DESC>],[<AIDDET>]" ;

REPT ALM COM Reports an alarm condition when an AID cannot be given. Output format: SID DATE TIME ** ATAG REPT ALM COM "[<AID>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>],[<OCRTM>],,:[<DESC>]" ;

REPT EVT <MOD2ALM> Reports the occurrence of a non-alarmed event. Output format: SID DATE TIME A ATAG REPT EVT <MOD2ALM> "<AID>:<CONDTYPE>,[<CONDEFF>],,,[<LOCN>],,[<MONVAL>],[<THLEV>], [<TMPER>]:[<DESC>],[<AIDDET>]" ;

REPT EVT COM Reports a non-alarmed event against an NE when there is no AID associated with it. Output format: SID DATE TIME A ATAG REPT EVT COM "[<AID>]:<CONDTYPE>,[<CONDEFF>],,,,,,,:[<DESC>]" ;

RTRV-ALM-ALL:[<TID>]:[<AID>]:<CTAG>::[<NTFCNCDE>],[<CONDITION>], [<SRVEFF>][,,,]; Retrieves and sends the current status of all active alarm conditions. Output format: SID DATE TIME M CTAG COMPLD "[<AID>],[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>, <OCRDAT>,<OCRTM>,,:[<DESC>],[<AIDDET>]" ;

RTRV-COND-<MOD2ALM>:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,]; Retrieves the current standing condition and/or state associated with an entity. Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>], [<OCRTM>],,,[<DESC>]" ;

RTRV-COND-ALL:[<TID>]:[<AID>]:<CTAG>::[<TYPEREQ>][,,,]; Retrieves the current standing condition for all entities. Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>], [<OCRTM>],,,[<DESC>]" ;

8 File Transfer

Table 8 File Transfer 

APPLY:[<TID>]::<CTAG>[::<MEM_SW_TYPE>]; Activates or reverts a software load during a software upgrade or downgrade.

COPY-IOSCFG:[<TID>]:<AID>:<CTAG>::SRC=<SRC>,DEST=<DEST>; Uploads the startup IOS configuration file from the network to the node. Downloads the startup IOS configuration file from the node to the network.

COPY-RFILE:[<TID>]:<SRC>:<CTAG>::TYPE=<XFERTYPE>,[SRC=<SRC1>], [DEST=<DEST>],[OVWRT=<OVWRT>],[FTTD=<FTTD>]; Downloads a new software package from the location specified by the FTP URL. Performs backup/restore on the database and archives the audit-log.

REPT EVT FXFR Reports the FTP software download status of the start, completion and completed percentage. Output format: SID DATE TIME A ATAG REPT EVT FXFR "<FILENAME>,<FXFR_STATUS>,[<FXFR_RSLT>],[<PRCNT_XFRD>]" ;

REPT EVT IOSCFG Reports the status of copying the IOS configuration file, when the COPY-IOSCFG command is issued. Output format: SID DATE TIME A ATAG REPT EVT IOSCFG "<AID>:<SRC>,<DEST>,<STATUS>,[<RESULT>]" ;

9 Log

Table 9 Log 

ALW-MSG-DBCHG:[<TID>]::<CTAG>[::,,]; Enables REPT DBCHG.

INH-MSG-DBCHG:[<TID>]::<CTAG>[::,,]; Disables REPT DBCHG.

REPT DBCHG Reports any changes on the NE that result from certain TL1 commands or an external event. Output format: SID DATE TIME A ATAG REPT DBCHG "TIME=<TIME>,DATE=<DATE>,[SOURCE=<SOURCE>],[USERID=<USERID>], DBCHGSEQ=<DBCHGSEQ>:<COMMAND>:<AID>:::<PSTPSTQ>,<SST>" ;

RTRV-AUDIT-LOG:[<TID>]::<CTAG>; Retrieves the contents of the audit log stored in the NE. Output format: SID DATE TIME M CTAG COMPLD "<ENTRYNUM>,<OCRDAT>,<OCRTM>,<TASKID>,<TXSTATUS>,<DESCRIPTION>" ;

RTRV-LOG:[<TID>]::<CTAG>::<LOGNM>; Retrieves the alarm log of the NE. Output format: SID DATE TIME M CTAG COMPLD "<AID>,<ALMNUMBER>:CURRENT=<CURRENT>,[PREVIOUS=<PREVIOUS>], <CONDITION>,<SRVEFF>,[TIME=<OCRTIME>],[DATE=<OCRDAT>]:<ALMDESCR>" ;

10 Network

Table 10 Network 

RTRV-MAP-NETWORK:[<TID>]::<CTAG>; Reports all the NE attributes that are reachable from the gateway NE (GNE).

RTRV-NE-IPMAP:[<TID>]:[<AID>]:<CTAG>; Retrieves the IP address and node name of the NEs that have the data communications channel (DCC) connection with this NE. Output format: SID DATE TIME M CTAG COMPLD "<AID>:<IPADDR>,<NODENAME>" ;

11 Paths

Table 11 Paths 

ED-<MOD_PATH>:[<TID>]:<AID>:<CTAG>:::[SFBER=<SFBER>],[SDBER=<SDBER>], [RVRTV=<RVRTV>],[RVTM=<RVTM>],[SWPDIP=<SWPDIP>], [HOLDOFFTIMER=<HOLDOFFTIMER>],[EXPTRC=<EXPTRC>],[TRC=<TRC>], [TRCMODE=<TRCMODE>],[TACC=<TACC>],[TAPTYPE=<TAPTYPE>], [CMDMDE=<CMDMDE>]:[<PST>[,<SST>]]; Modifies the attributes associated with a VC or virtual tributary (VT) path.

RTRV-<PATH>:[<TID>]:<AID>:<CTAG>[:::MSSPRPTHTYPE=<MSSPRPTHTYPE>][:]; Retrieves the attributes associated with an SDH high/low order path. Output format: SID DATE TIME M CTAG COMPLD "<AID>::[LEVEL=<LEVEL>],[SFBER=<SFBER>],[SDBER=<SDBER>],[RVRTV=<RVRTV>], [RVTM=<RVTM>],[SWPDIP=<SWPDIP>],[HOLDOFFTIMER=<HOLDOFFTIMER>], [EXPTRC=<EXPTRC>],[TRC=<TRC>],[INCTRC=<INCTRC>],[TRCMODE=<TRCMODE>], [TACC=<TACC>],[TAPTYPE=<TAPTYPE>],[SNCPPTHSTATE=<SNCPPTHSTATE>], [C2=<C>],[MSSPRPTHSTATE=<MSSPRPTHSTATE>]:<PSTPSTQ>,[<SSTQ>]" ;

12 Performance

Table 12 Performance 

ALW-PMREPT-ALL:[<TID>]::<CTAG>; Resumes the processing of all inhibited PM reports.

DLT-RMONTH-<MOD2_RMON>:[<TID>]:<SRC>:<CTAG>::<MONTYPE>,,,,<INTVL>: RISE=<RISE>,FALL=<FALL>,[SAMPLE=<SAMPLE>],[STARTUP=<STARTUP>][:]; Deletes a threshold entry in the RMON alarm table.

ENT-RMONTH-<MOD2_RMON>:[<TID>]:<SRC>:<CTAG>::<MONTYPE>,,,,<INTVL>: RISE=<RISE>,FALL=<FALL>,[SAMPLE=<SAMPLE>],[STARTUP=<STARTUP>][:]; Creates an entry in the RMON alarm table for the threshold of data statistics that are managed by the RMON engine.

INH-PMREPT-ALL:[<TID>]::<CTAG>; Inhibits all scheduled PM reporting.

INIT-REG-<MOD2>:[<TID>]:<AID>:<CTAG>::<MONTYPE>,,[<LOCN>],[<DIRN>], [<TMPER>][,,]; Initializes the performance monitoring (PM) registers.

REPT PM <MOD2> Reports of performance monitoring statistics as a result of schedule created by the SCHED-PMREPT command. Output format: SID DATE TIME A ATAG REPT PM <MOD2> "<AID>:<MONTYPE>,<MONVAL>,<VLDTY>,<LOCN>,<DIRN>,<TMPER>, <MONDAT>,<MONTM>" ;

RTRV-BFDLPM-<MOD2>:[<TID>]:<AID>:<CTAG>:::REQTYPE=<REQTYPE>; Retrieves the BFDL performance monitoring parameters. Output format: SID DATE TIME M CTAG COMPLD "<AID>:<MONTYPE>,<MONVAL>,<BUCKET>" ;

RTRV-PM-<MOD2>:[<TID>]:<AID>:<CTAG>::[<MONTYPE>],[<MONLEV>],[<LOCN>], [<DIRECTION>],[<TMPER>],[<DATE>],[<TIME>]; Retrieves the values of PM parameters for a specified card type. Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:<MONTYPE>,<MONVAL>,[<VLDTY>],[<LOCN>],[<DIRECTION>], [<TMPER>],[<MONDAT>],[<MONTM>]" ;

RTRV-PMMODE-<VC_PATH>:[<TID>]:<SRC>:<CTAG>::<LSTM>; Retrieves the PM mode that has been previously set in the NE data collection. Output format: SID DATE TIME M CTAG COMPLD "<CROSSCONNECTID>:[<LSTM>],<MODETYPE>" ;

RTRV-PMSCHED-<MOD2>:[<TID>]:<AID>:<CTAG>; Retrieves the PM reporting schedule that was set for the NE by the SCHED-PMREPT command. Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:<REPTINVL>,<REPTDAT>,<REPTTM>,[<NUMINVL>],, [<MONLEV>],<LOCN>,,[<TMPER>],[<TMOFST>],[<INHMODE>]" ;

RTRV-PMSCHED-ALL:[<TID>]::<CTAG>; Retrieves all the PM reporting schedules that were set for the NE by SCHED-PMREPT. Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:<REPTINVL>,<REPTDAT>,<REPTTM>,[<NUMINVL>],, [<MONLEV>],<LOCN>,,[<TMPER>],<TMOFST>,[<INHMODE>]" ;

RTRV-RMONTH-<MOD2_RMON>:[<TID>]:<AID>:<CTAG>::[<MONTYPE>],,,, [<INTVL>]:[RISE=<RISE>],[FALL=<FALL>],[SAMPLE=<SAMPLE>],[STARTUP=<STARTUP>][:]; Retrieves the thresholds defined in the RMON alarm table. Output format: SID DATE TIME M CTAG COMPLD "<AIDUNIONID>,<AIDTYPE>:<MONTYPE>,,,,<INTVL>:INDEX=<INDEX>,RISE=<RISE>, FALL=<FALL>,SAMPLE=<SAMPLE>,STARTUP=<STARTUP>" ;

RTRV-TH-<MOD2>:[<TID>]:<AID>:<CTAG>::[<MONTYPE>],[<LOCN>],<TMPER>[::]; Retrieves the current threshold level of one or more monitored parameters. Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:<MONTYPE>,[<LOCN>],,<THLEV>,[<TMPER>]" ;

RTRV-TH-ALL:[<TID>]::<CTAG>::[<MONTYPE>],[<LOCATION>],[<TMPER>][::]; Retrieves the current threshold level of all monitored parameters. Output format: SID DATE TIME M CTAG COMPLD "<AID>,<AIDTYPE>:<MONTYPE>,<LOCATION>,,<THLEV>,<TMPER>" ;

SCHED-PMREPT-<MOD2>:[<TID>]:<SRC>:<CTAG>::[<REPTINVL>], [<REPTSTATM>],[<NUMREPT>],,[<MONLEV>],[<LOCN>],,[<TMPER>],[<TMOFST>]; Schedules/reschedules the NE to report the performance monitoring data for a line facility or for an STM/VC path periodically, using an automatic REPT PM message.

SET-TH-<MOD2>:[<TID>]:<AID>:<CTAG>::<MONTYPE>,<THLEV>,[<LOCN>],,[<TMPER>]; Sets the threshold for PM and sets the alarm thresholds for the MXP_2.5G_10G and TXP_MR_10G cards.

13 Ports

Table 13 Ports 

DLT-<MOD1PAYLOAD>:[<TID>]:<AID>:<CTAG>[::::]; Deletes the specified port.

ED-<GIGE_TYPE>:[<TID>]:<AID>:<CTAG>:::[ADMINSTATE=<ADMINSTATE>], [LINKSTATE=<LINKSTATE>],[MTU=<MTU>],[FLOWCTRL=<FLOWCTRL>], [AUTONEG=<AUTONEG>],[HIWMRK=<HIWMRK>],[LOWMRK=<LOWMRK>], [OPTICS=<OPTICS>],[DUPLEX=<DUPLEX>],[SPEED=<SPEED>],[NAME=<NAME>], [CMDMDE=<CMDMDE>],[MACADDR=<MACADDR>],[FREQ=<FREQ>],[LOSSB=<LOSSB>], [SOAK=<SOAK>]:[<PST>[,<SST>]]; Edits Gigabit Ethernet facility attributes.

ED-<MOD1FCPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[LINKRCVRY=<LINKRCVRY>], [DISTEXTN=<DISTEXTN>],[AUTODETECTION=<AUTODETECTION>], [LINKCREDITS=<LINKCREDITS>],[MFS=<MFS>],[NAME=<NAME>], [CMDMDE=<CMDMDE>],[SOAK=<SOAK>],[FREQ=<FREQ>], [LOSSB=<LOSSB>]:[<PST>[,<SST>]]; Edits the attributes related with the Fibre Channel facility.

ED-<MOD1FICONPAYLOAD>:[<TID>]:<AID>:<CTAG>:::[LINKRCVRY=<LINKRCVRY>], [DISTEXTN=<DISTEXTN>],[AUTODETECTION=<AUTODETECTION>], [LINKCREDITS=<LINKCREDITS>],[MFS=<MFS>],[NAME=<NAME>], [CMDMDE=<CMDMDE>],[SOAK=<SOAK>],[FREQ=<FREQ>], [LOSSB=<LOSSB>]:[<PST>[,<SST>]]; Edits the attributes related to the FICON payload facility.

ED-<STM_TYPE>:[<TID>]:<AID>:<CTAG>:::[DCC=<DCC>],[AREA=<AREA>], [SYNCMSG=<SYNCMSG>],[SENDDUS=<SENDDUS>],[PJMON=<PJMON>], [SFBER=<SFBER>],[SDBER=<SDBER>],[MODE=<MODE>],[MUX=<MUX>],[SOAK=<SOAK>], [OSPF=<OSPF>],[LDCC=<LDCC>],[NAME=<NAME>],[CMDMDE=<CMDMDE>], [EXPTRC=<EXPTRC>],[TRC=<TRC>],[TRCMODE=<TRCMODE>], [TRCFORMAT=<TRCFORMAT>],[ADMSSM=<ADMSSM>],[SENDDUSFF=<SENDDUSFF>], [AISONLPBK=<AISONLPBK>],[FREQ=<FREQ>],[LOSSB=<LOSSB>], [FOREIGNFEND=<FOREIGNFEND>],[FOREIGNIP=<FOREIGNIP>]:[<PST>[,<SST>]]; Modifies the attributes (that is, service parameters) and state of an STM facility.

ED-ALS:[<TID>]:<SRC>:<CTAG>:::[ALSMODE=<ALSMODE>],[ALSRCINT=<ALSRCINT>], [ALSRCPW=<ALSRCPW>][:]; Modifies the automatic laser shutdown (ALS) attributes of an STM facility and in general for all the facilities that support the ALS feature.

ED-DS3I:[<TID>]:<AID>:<CTAG>:::[FMT=<FMT>],[LINECDE=<LINECDE>],[LBO=<LBO>], [INHFELPBK=<INHFELPBK>],[TACC=<TACC>],[TAPTYPE=<TAPTYPE>],[SFBER=<SFBER>], [SDBER=<SDBER>],[SOAK=<SOAK>],[NAME=<NAME>], [CMDMDE=<CMDMDE>]:[<PST>[,<SST>]]; Modifies the attributes of a DS3i-N-12 facility.

ED-E1:[<TID>]:<AID>:<CTAG>:::[LINECDE=<LINECDE>],[FMT=<FMT>],[TACC=<TACC>], [TAPTYPE=<TAPTYPE>],[SFBER=<SFBER>],[SDBER=<SDBER>],[SOAK=<SOAK>], [NAME=<NAME>],[CMDMDE=<CMDMDE>],[SYNCMSG=<SYNCMSG>], [SENDDUS=<SENDDUS>],[RETIME=<RETIME>],[ADMSSM=<ADMSSM>], [SABIT=<SABIT>]:[<PST>[,<SST>]]; Supports provisioning of an E1 facility.

ED-E3:[<TID>]:<AID>:<CTAG>:::[TACC=<TACC>],[TAPTYPE=<TAPTYPE>],[SFBER=<SFBER>], [SDBER=<SDBER>],[SOAK=<SOAK>],[NAME=<NAME>], [CMDMDE=<CMDMDE>]:[<PST>[,<SST>]]; Supports provisioning of an E3 facility.

ED-E4:[<TID>]:<AID>:<CTAG>:::[SFBER=<SFBER>],[SDBER=<SDBER>],[SOAK=<SOAK>], [NAME=<NAME>],[CMDMDE=<CMDMDE>]:[<PST>[,<SST>]];[<DNFIELD>]; Modifies the attributes and the state of the E4 port facility.

ED-FAC:[<TID>]:<SRC>:<CTAG>:::[PAYLOAD=<PAYLOAD>], [CMDMDE=<CMDMDE>]:[<PST>[,<SST>]]; Provisions the payload (or signal) type of the facility.

ED-FSTE:[<TID>]:<AID>:<CTAG>:::[FLOW=<FLOW>],[EXPDUPLEX=<EXPDUPLEX>], [EXPSPEED=<EXPSPEED>],[VLANCOS=<VLANCOS>],[IPTOS=<IPTOS>],[NAME=<NAME>], [CMDMDE=<CMDMDE>],[SOAK=<SOAK>]:[<PST>[,<SST>]] Edits the front end port information of the Fast Ethernet (10/100 Mbps) card.

ED-G1000:[<TID>]:<AID>:<CTAG>:::[MFS=<MFS>],[FLOW=<FLOW>], [LOWMRK=<LOWMRK>],[HIWMRK=<HIWMRK>],[AUTONEG=<AUTONEG>], [NAME=<NAME>],[CMDMDE=<CMDMDE>],[SOAK=<SOAK>]:[<PST>[,<SST>]]; Modifies the attributes related to a G1000 port.

ED-GFP:[<TID>]:<AID>:<CTAG>:::[FCS=<FCS>],[AUTOTHGFPBUF=<AUTOTHGFPBUF>], [GFPBUF=<GFPBUF>],[FILTER=<FILTER>]; Edit generic framing procedure (GFP); used for GFP management.

ED-POS:[<TID>]:<AID>:<CTAG>:::[ENCAP=<ENCAP>],[NAME=<NAME>], [CMDMDE=<CMDMDE>],[SOAK=<SOAK>]:[<PST>[,<SST>]]; Edit packet-over-SDH (POS); used for POS management.

ED-STM1E:[<TID>]:<SRC>:<CTAG>:::[SYNCMSG=<SYNCMSG>],[SENDDUS=<SENDDUS>], [SFBER=<SFBER>],[SDBER=<SDBER>],[SOAK=<SOAK>],[NAME=<NAME>], [CMDMDE=<CMDMDE>]:[<PST>[,<SST>]]; Modifies the attributes and the state of the STM1E port facility.

ENT-<MOD1PAYLOAD>:[<TID>]:<AID>:<CTAG>[::::]; Creates the specified port.

OPR-ALS:[<TID>]:<AID>:<CTAG>[::::]; Restarts the laser of an STM facility.

RMV-<MOD2>:[<TID>]:<AID>:<CTAG>[::]; Removes a facility from service.

RST-<MOD2>:[<TID>]:<AID>:<CTAG>::::[<PST>[,<SST>]]; Provisions a facility or service.

RTRV-<MOD1FCPAYLOAD>:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the attributes related with the Fibre Channel (FC) port. Output format: SID DATE TIME M CTAG COMPLD "<AID>:,,[<ROLE>],[<STATUS>]:LINKRATE=<LINKRATE>,LINKSTATE=<LINKSTATE>, [LINKRCVRY=<LINKRCVRY>],[DISTEXTN=<DISTEXTN>], [LINKCREDITS=<LINKCREDITS>],[MFS=<MFS>],[ENCAP=<ENCAP>],[NAME=<NAME>], [SOAK=<SOAK>],[SOAKLEFT=<SOAKLEFT>],[FREQ=<FREQ>],[LOSSB=<LOSSB>]: <PST_PSTQ>,[<SST>]" ;

RTRV-<MOD1FICONPAYLOAD>:[<TID>]:<AID>:<CTAG>; Returns Fibre Channel specific settings for ports that have been configured to carry FICON traffic using the ENT-FICON command. Output format: SID DATE TIME M CTAG COMPLD "<AID>::[<ROLE>],[<STATUS>]:[LINKRATE=<LINKRATE>],[LINKSTATE=<LINKSTATE>], [LINKRCVRY=<LINKRCVRY>],[DISTEXTN=<DISTEXTN>], [LINKCREDITS=<LINKCREDITS>],[MFS=<MFS>],[ENCAP=<ENCAP>],[NAME=<NAME>], [SOAK=<SOAK>],[SOAKLEFT=<SOAKLEFT>],[FREQ=<FREQ>],[LOSSB=<LOSSB>]: <PST_PSTQ>,<SST>" ;

RTRV-<STM_TYPE>:[<TID>]:<AID>:<CTAG>[MSSPRPTHTYPE=<MSSPRPTHTYPE>:::][:; Retrieves the attributes (that is, service parameters) and state of an STM facility. Output format: SID DATE TIME M CTAG COMPLD "<AID>:,,[<ROLE>],[<STATUS>]:[DCC=<DCC>],[AREA=<AREA>],[TMGREF=<TMGREF>], [SYNCMSG=<SYNCMSG>],[SENDDUS=<SENDDUS>],[PJMON=<PJMON>], [SFBER=<SFBER>],[SDBER=<SDBER>],[MODE=<MODE>],[WVLEN=<WVLEN>], [RINGID=<RINGID>],[MSSPRTYPE=<MSSPRTYPE>],[MUX=<MUX>],[UNIC=<UNIC>], [CCID=<CCID>],[NBRIX=<NBRIX>],[SOAK=<SOAK>],[SOAKLEFT=<SOAKLEFT>], [SSMRCV=<SSMRCV>],[OSPF=<OSPF>],[LDCC=<LDCC>],[NAME=<NAME>], [LBCL=<LBCL>],[OPT=<OPT>],[OPR=<OPR>],[EXPTRC=<EXPTRC>],[TRC=<TRC>], [TRCMODE=<TRCMODE>],[TRCFORMAT=<TRCFORMAT>],[ADMSSM=<ADMSSM>], [SENDDUSFF=<SENDDUSFF>],[AISONLPBK=<AISONLPBK>],[FREQ=<FREQ>], [LOSSB=<LOSSB>],[FOREIGNFEND=<FOREIGNFEND>], [FOREIGNIPADDRESS=<FOREIGNIPADDRESS>],:<PSTPSTQ>,[<SSTQ>]" ;

RTRV-10GIGE:[<TID>]:<AID>:<CTAG>[::::]; Used to retrieve the 10-Gbps-specific parameters for a port configured to support the gigabyte Ethernet payload using the ENT-10GIGE command. Output format: SID DATE TIME M CTAG COMPLD "<AID>::[<ROLE>],[<STATUS>]:[NAME=<NAME>],[MACADDR=<MACADDR>], [LBCL=<LBCL>],[OPT=<OPT>],[OPR=<OPR>],[FREQ=<FREQ>],[LOSSB=<LOSSB>]: <PSTPSTQ>,[<SST>]" ;

RTRV-ALS:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the ALS attributes of an STM facility and in general for all facilities that support the ALS feature. Output format: SID DATE TIME M CTAG COMPLD "<AID>,<AIDTYPE>::[ALSMODE=<ALSMODE>],[ALSRCINT=<ALSRCINT>], [ALSRCPW=<ALSRCPW>],[LSRSTAT=<LSRSTAT>]" ;

RTRV-DS3I:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the properties of a DS3i-N-12 facility. Output format: SID DATE TIME M CTAG COMPLD "<AID>::FMT=<FMT>,LINECDE=<LINECDE>,LBO=<LBO>,[INHFELPBK=<INHFELPBK>], [TACC=<TACC>],[TAPTYPE=<TAPTYPE>],[SFBER=<SFBER>],[SDBER=<SDBER>], [SOAK=<SOAK>],[SOAKLEFT=<SOAKLEFT>],[NAME=<NAME>]:<PSTPSTQ>,[<SSTQ>" ;

RTRV-E1:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the attributes and state information of an E1 port facility. Output format: SID DATE TIME M CTAG COMPLD "<AID>::LINECDE=<LINECDE>,FMT=<FMT>,[TACC=<TACC>],[TAPTYPE=<TAPTYPE>], [SFBER=<SFBER>],[SDBER=<SDBER>],[SOAK=<SOAK>],[SOAKLEFT=<SOAKLEFT>], [NAME=<NAME>],[SYNCMSG=<SYNCMSG>],[SENDDUS=<SENDDUS>], [RETIME=<RETIME>],[ADMSSM=<ADMSSM>],[PROVIDESYNC=<PROVIDESYNC>], [SABIT=<SABIT>]:<PSTPSTQ>,[<SSTQ>]" ;

RTRV-E3:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the attributes and state information of an E3 port facility. Output format: SID DATE TIME M CTAG COMPLD "<AID>::[TACC=<TACC>],[TAPTYPE=<TAPTYPE>],[SFBER=<SFBER>], [SDBER=<SDBER>],[SOAK=<SOAK>],[SOAKLEFT=<SOAKLEFT>], [NAME=<NAME>]:<PST_PSTQ>,[<SSTQ>]" ;

RTRV-E4:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the attributes and state information of an E4 port facility. Output format: SID DATE TIME M CTAG COMPLD "<AID>::[PAYLOAD=<PAYLOAD>],[SFBER=<SFBER>],[SDBER=<SDBER>],[SOAK=<SOAK>], [SOAKLEFT=<SOAKLEFT>],[NAME=<NAME>]:<PSTPSTQ>,[<SSTQ>]" ;

RTRV-ESCON:[<TID>]:<AID>:<CTAG>; Retrieves Fibre Channel specific settings for ports that have been configured to carry ESCON traffic using the ENT-ESCON command. Output format: SID DATE TIME M CTAG COMPLD "<AID>:,,[<ROLE>],[<STATUS>]:[ENCAP=<ENCAP>]" ;

RTRV-FAC:[<TID>]:<SRC>:<CTAG>[::::]; Retrieves the payload type of the facility. Output format: SID DATE TIME M CTAG COMPLD "<SRC>::PAYLOAD=<PAYLOAD>:<PST_PSTQ>,[<SSTQ>]" ;

RTRV-FSTE:[<TID>]:<AID>:<CTAG>; Retrieves the front end port information of a Fast Ethernet (10/100 Mbps) card. Output format: SID DATE TIME M CTAG COMPLD "<AID>::[ADMINSTATE=<ADMINSTATE>],[LINKSTATE=<LINKSTATE>],[MTU=<MTU>], [FLOWCTRL=<FLOWCTRL>],[DUPLEX=<DUPLEX>],[SPEED=<SPEED>],[FLOW=<FLOW>], [EXPDUPLEX=<EXPDUPLEX>],[EXPSPEED=<EXPSPEED>],[VLANCOS=<VLANCOS>], [IPTOS=<IPTOS>],[OPTICS=<OPTICS>],[NAME=<NAME>],[SOAK=<SOAK>], [SOAKLEFT=<SOAKLEFT>]:<PST_PSTQ>,[<SSTQ>]" ;

RTRV-G1000:[<TID>]:<AID>:<CTAG>; Retrieves the G1000 facilities configuration. Output format: SID DATE TIME M CTAG COMPLD "<AID>::[MFS=<MFS>],[FLOW=<FLOW>],[LAN=<LAN>],[OPTICS=<OPTICS>], [TRANS=<TRANS>],[TPORT=<TPORT>],[LOWMRK=<LOWMRK>], [HIWMRK=<HIWMRK>],[AUTONEG=<AUTONEG>],[ENCAP=<ENCAP>], [NAME=<NAME>],[SOAK=<SOAK>],[SOAKLEFT=<SOAKLEFT>]:<PST_PSTQ>,[<SSTQ>]" ;

RTRV-GFP:[<TID>]:<SRC>:<CTAG>; Retrieves GFP; used for GFP management. Output format: SID DATE TIME M CTAG COMPLD "<AID>::[FCS=<FCS>],[AUTOTHGFPBUF=<AUTOTHGFPBUF>],[GFPBUF=<GFPBUF>], [FILTER=<FILTER>]" ;

RTRV-GIGE:[<TID>]:<AID>:<CTAG>; Retrieves front end port information of a 1 Gigabit Ethernet card. Output format: SID DATE TIME M CTAG COMPLD "<AID>:,,<ROLE>,<STATUS>:[ADMINSTATE=<ADMINSTATE>], [LINKSTATE=<LINKSTATE>],[MTU=<MTU>],[ENCAP=<ENCAP>], [FLOWCTRL=<FLOWCTRL>],[AUTONEG=<AUTONEG>],[HIWMRK=<HIWMRK>], [LOWMRK=<LOWMRK>],[OPTICS=<OPTICS>],[DUPLEX=<DUPLEX>],[SPEED=<SPEED>], [NAME=<NAME>],[FREQ=<FREQ>],[LOSSB=<LOSSB>],[SOAK=<SOAK>], [SOAKLEFT=<SOAKLEFT>]:<PST>,<SST>" ;

RTRV-POS:[<TID>]:<AID>:<CTAG>; Retrieves the back-end port information for the Ethernet card, when the back-end port is working in POS mode. Output format: SID DATE TIME M CTAG COMPLD "<AID>::[ADMINSTATE=<ADMINSTATE>],[LINKSTATE=<LINKSTATE>],[MTU=<MTU>], [ENCAP=<ENCAP>],[NAME=<NAME>],[SOAK=<SOAK>],[SOAKLEFT=<SOAKLEFT>]: <PST_PSTQ>,[<SST>]" ;

RTRV-STM1E:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the attributes and state information of an STM1E facility. Output format: SID DATE TIME M CTAG COMPLD "<AID>::[PAYLOAD=<PAYLOAD>],[SYNCMSG=<SYNCMSG>],[SENDDUS=<SENDDUS>], [SFBER=<SFBER>],[SDBER=<SDBER>],[SOAK=<SOAK>],[SOAKLEFT=<SOAKLEFT>], [NAME=<NAME>]:<PST_PSTQ>,[<SSTQ>" ;

14 Protection

Table 14 Protection 

DLT-FFP-<STM_TYPE>:[<TID>]:<WORK>,<PROTECT>:<CTAG>[:::]; Deletes a facility protection group (STM4, STM64, STM1, STM16).

ED-FFP-<STM_TYPE>:[<TID>]:<AID>:<CTAG>:::[PROTID=<PROTID>],[RVRTV=<RVRTV>], [RVTM=<RVTM>],[PSDIRN=<PSDIRN>],[VRGRDTM=<VRGRDTM>], [DTGRDTM=<DTGRDTM>],[RCGRDTM=<RCGRDTM>][:]; Edits a facility protection group (STM4, STM64, STM1, STM16).

ENT-FFP-<STM_TYPE>:[<TID>]:<WORK>,<PROTECT>:<CTAG>:::[PROTTYPE= <PROTTYPE>],[PROTID=<PROTID>],[RVRTV=<RVRTV>],[RVTM=<RVTM>], [PSDIRN=<PSDIRN>],[OPOTYPE=<OPOTYPE>],[VRGRDTM=<VRGRDTM>], [DTGRDTM=<DTGRDTM>],[RCGRDTM=<RCGRDTM>][:]; Enters a facility protection group (STM4, STM64, STM1, STM16).

OPR-PROTNSW-<STM_TYPE>:[<TID>]:<AID>:<CTAG>::<SC>,[<SWITCHTYPE>][:<DIRN>]; Operates a protection switch (STM4, STM64, STM1, STM16).

OPR-PROTNSW-<PATH>:[<TID>]:<SRC>:<CTAG>::<SC>[:]; Instructs an SDH NE to initiate a subnetwork connection protection (SNCP) switch request.

REPT SW Reports the autonomous switching of a unit in a duplex equipment unit pair to standby and its mate unit to the active state. Output format: SID DATE TIME A ATAG REPT SW "<ACTID>,<STDBYID>" ;

RLS-PROTNSW-<STM_TYPE>:[<TID>]:<AID>:<CTAG>[::<DIRECTION>]; Instructs an SDH NE to release (clear) an SDH line protection switch request.

RLS-PROTNSW-<PATH>:[<TID>]:<SRC>:<CTAG>[::]; Instructs an SDH NE to release (clear) an SDH path protection switch request that was established with the OPR-PROTNSW-(MOD_PATH) command.

RTRV-FFP:[<TID>]:<AID>:<CTAG>[::::]; Retrieves all optical 1+1 protection groups Output format: SID DATE TIME M CTAG COMPLD "<WORK>,<PROTECT>:<LEVEL>:[PROTID=<PROTID>],[RVRTV=<RVRTV>], [RVTM=<RVTM>],[PSDIRN=<PSDIRN>],[VRGRDTM=<VRGRDTM>], [DTGRDTM=<DTGRDTM>],[RCGRDTM=<RCGRDTM>],[OPOTYPE=<OPOTYPE>]" ;

RTRV-FFP-<STM_TYPE>:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the optical facility protection information. Output format: SID DATE TIME M CTAG COMPLD "<WORK>,<PROTECT>::[PROTID=<PROTID>,][RVRTV=<RVRTV>,][RVTM=<RVTM>,] [PSDIRN=<PSDIRN>,][VRGRDTM=<VRGRDTM>,][DTGRDTM=<DTGRDTM>,] [RCGRDTM=<RCGRDTM>,][OPOTYPE=<OPOTYPE>]" ;

RTRV-PROTNSW-<STM_TYPE>:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the switching state of an SDH line. Output format: SID DATE TIME M CTAG COMPLD "<AID>:<SC>,[<SWITCHTYPE>]" ;

15 Provisionable Patchcords

Table 15 Provisionable Patchcords 

DLT-LNKTERM:[<TID>]:<AID>:<CTAG>; Deletes a provisionable patchcord termination that is present on a node.

ED-LNKTERM:[<TID>]:<AID>:<CTAG>:::[REMOTENODE=<REMOTENODE>,] [REMOTELNKTERMID=<REMOTELNKTERMID>]; Edits the attributes of an existing provisionable patchcord termination.

ENT-LNKTERM:[<TID>]:<AID>:<CTAG>:::PORT=<PORT>, [REMOTENODE=<REMOTENODE>],REMOTELNKTERMID=<REMOTELNKTERMID>; Creates a provisionable patchcord termination (virtual link) on a physical interface.

RTRV-LNKTERM:[<TID>]:<AID>:<CTAG>; Retrieves information about one or more provisionable patchcord terminations. Output format: SID DATE TIME M CTAG COMPLD "<AID>::PORT=<PORT>,[REMOTENODE=<REMOTENODE>], [REMOTELNKTERMID=<REMOTELNKTERMID>]" ;

16 Security

Table 16 Security 

ACT-USER:[<TID>]:<UID>:<CTAG>::<PID>; Sets up a session with the NE. Output format: SID DATE TIME M CTAG COMPLD "<UID>:<LASTLOGINTIME>,<UNSUCCESSFULLOGINS>" ;

ALW-CONSOLE-PORT:[<TID>]:<AID>:<CTAG>; Turns on the console port for the ML-Series cards.

ALW-MSG-SECU:[<TID>]::<CTAG>; Allows REPT EVT SECU and REPT ALM SECU.

ALW-MSG-SECU:[<TID>]::<CTAG>[::,,]; Enables the REPT EVT SECU and REPT ALM SECU autonomous messages.

ALW-USER-SECU:[<TID>]::<CTAG>::<UID>; Enables a user ID that has been disabled (by way of the INH-USER-SECU command) so the user can establish a session with the NE.

CANC Reports the occurrence of a session timeout event. Output format: SID DATE TIME A ATAG CANC "<UID>" ;

CANC-USER:[<TID>]:<USERID>:<CTAG>; Logs a user out of an active session with the NE.

CANC-USER-SECU:[<TID>]:<UID>:<CTAG>; Logs out all sessions on the NE (TL1, CTC, etc.) of a user whose userid matches the UID specified in the command.

CLR-COND-SECU:[<TID>]::<CTAG>[::<SECUALMTYPE>]; Clears the specified standing condition.

DLT-USER-SECU:[<TID>]:<UID>:<CTAG>; Deletes a user; can only be performed by a Superuser.

ED-CMD-SECU:[<TID>]:<AID>:<CTAG>::<CAP>; Edits the command security level of a particular command.

ED-PID:[<TID>]:<UID>:<CTAG>::<OLDPID>,<NEWPID>; Allows a user to change his or her own password.

ED-PROTOCOL:[<TID>]:<PROTOCOLAID>:<CTAG>::<PROTOCOLSTAT>; Enables/disables a protocol/service that is supported in the NE.

ED-USER-SECU:[<TID>]:<UID>:<CTAG>::[<NEWUID>],[<NEWPID>],,[<UAP>][:]; Edits a user's privileges, password, or ID and can only be performed by a Superuser.

ENT-USER-SECU:[<TID>]:<UID>:<CTAG>::<PID>,,<UAP>[:]; Adds a user account; can only be performed by a Superuser.

INH-CONSOLE-PORT:[<TID>]:<AID>:<CTAG>; Turns off the console port for the ML-Series cards.

INH-MSG-SECU:[<TID>]::<CTAG>; Inhibits the REPT EVT SECU and REPT ALM SECU messages.

INH-USER-SECU:[<TID>]::<CTAG>::<UID>; Disables (without deleting) a userid, so the user is denied access to the NE.

REPT ALM SECU Reports the occurrence of an alarmed security event against the NE. Output format: SID DATE TIME ** ATAG REPT ALM SECU "<AID>:<NOTIFCODE>,<SECUALMTYPE>" ;

REPT EVT SECU Reports the occurrence of a non-alarmed security event against the NE. Output format: SID DATE TIME A ATAG REPT EVT SECU "<AID>:<DNFIELD>,[<CONDEFF>],,,,,,,:<SECURITY>:<DNFIELD1>" ;

REPT EVT SESSION Reports a non-alarmed event related to establishing a session with the NE. Output format: SID DATE TIME A ATAG REPT EVT SESSION "<AID>:<EXP>,<PCN>" "<WARN>" ;

RTRV-CMD-SECU:[<TID>]:<AID>:<CTAG>; Retrieves the current command security level of the command specified in the AID field. Output format: SID DATE TIME M CTAG COMPLD "<AID>:<CAP>" ;

RTRV-CONSOLE-PORT:[<TID>]:<AID>:<CTAG>; Retrieves the status of the console port for the ML-Series cards. Output format: SID DATE TIME M CTAG COMPLD "<EQPT>:PORT=<PORT>" ;

RTRV-DFLT-SECU:[<TID>]:<AID>:<CTAG>; Retrieves the system-wide default values associated with several security parameters. Output format: SID DATE TIME M CTAG COMPLD "<NE>:PAGE=<PAGE>,PCND=<PCND>,MXINV=<MXINV>,DURAL=<DURAL>, TMOUT=<TMOUT>,UOUT=<UOUT>,PFRCD=<PFRCD>,POLD=<POLD>,PINT=<PINT>, LOGIN=<LOGIN>,[PRIVLVL=<PRIVLVL>],[PDIF=<PDIF>]" ;

RTRV-USER-SECU:[<TID>]:<UID>:<CTAG>; Retrieves the security information of a specified user or list of users. Output format: SID DATE TIME M CTAG COMPLD "<UID>:,<PRIVILEGE>:LOGGEDIN=<LOGGEDIN>,[NUMSESSIONS=<NUMSESS>], [LOCKEDOUT=<LOCKEDOUT>],[DISABLED=<DISABLED>]" ;

SET-ATTR-SECUDFLT:[<TID>]::<CTAG>::[PAGE=<PAGE>],[PCND=<PCND>], [MXINV=<MXINV>],[DURAL=<DURAL>],[TMOUT=<TMOUT>],[UOUT=<UOUT>], [PFRCD=<PFRCD>],[POLD=<POLD>],[PINT=<PINT>],[LOGIN=<LOGIN>], [PRIVLVL=<PRIVLVL>],[PDIF=<PDIF>]; Sets the system-wide default values associated with several security parameters.

17 Synchronization

Table 17 Synchronization 

ED-BITS:[<TID>]:<AID>:<CTAG>:::[LINECDE=<LINECDE>],[FMT=<FMT>],[LBO=<LBO>], [SYNCMSG=<SYNCMSG>],[AISTHRSHLD=<AISTHRSHLD>],[SABIT=<SABIT>], [BITSFAC=<BITSFAC>],[ADMSSM=<ADMSSM>][:<PST>]; Edits the BITS reference attributes.

ED-NE-SYNCN:[<TID>]:[<AID>]:<CTAG>:::[TMMD=<TMMD>],[SSMGEN=<SSMGEN>], [QRES=<QRES>],[RVRTV=<RVRTV>],[RVTM=<RVTM>]; Edits the synchronization attributes of the NE.

ED-SYNCN:[<TID>]:<AID>:<CTAG>:::[PRI=<PRI>],[SEC=<SEC>],[THIRD=<THIRD>][:]; Edits the synchronization reference list used to determine the sources for the NE's reference clock and the BITS output clock.

OPR-SYNCNSW:[<TID>]:[<AID>]:<CTAG>::<SWITCHTO>,[<SC>]; Initiates a switch to the reference specified by the synchronization reference number if the reference supplied is valid.

REPT ALM BITS Reports an alarm condition on a BITS facility. Output format: SID DATE TIME ** ATAG REPT ALM BITS "<AID>:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>],[<OCRTM>],,:[<DESC>]" ;

REPT ALM SYNCN Reports an alarm condition against a synchronization reference. Output format: SID DATE TIME ** ATAG REPT ALM SYNCN "<AID>:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>], [<OCRTM>],,:[<DESC>],[<EQPTTYPE>]" ;

REPT EVT BITS Reports the occurrence of a non-alarmed event against a BITS facility. Output format: SID DATE TIME ** ATAG REPT ALM BITS "<AID>:<CONDTYPE>,[<CONDEFF>],,,,,,,:[<DESC>]" ;

REPT EVT SYNCN Reports the occurrence of a non-alarmed event against a synchronization entity. Output format: SID DATE TIME A ATAG REPT EVT SYNCN "<AID>:<CONDTYPE>,[<CONDEFF>],,,,,,,:[<DESC>],[<AIDDET>]" ;

RLS-SYNCNSW:[<TID>]:[<AID>]:<CTAG>; Releases the previous synchronization reference provided by the OPR-SYNCNSW command.

RTRV-ALM-BITS:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>],[<SRVEFF>][,,,]; Retrieves and sends the current status of alarm conditions associated with the BITS facility. Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>], [<OCRTM>],,:[<DESC>]" ;

RTRV-ALM-SYNCN:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<CONDTYPE>], [<SRVEFF>][,,,]; Retrieves and sends the current status of alarm conditions associated with a synchronization facility. Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:<NTFCNCDE>,<CONDTYPE>,<SRVEFF>,[<OCRDAT>], [<OCRTM>],,:[<DESC>]" ;

RTRV-BITS:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the BITS configuration command. Output format: SID DATE TIME M CTAG COMPLD "<AID>::[LINECDE=<LINECDE>],[FMT=<FMT>],[LBO=<LBO>],[SYNCMSG=<SYNCMSG>], [AISTHRSHLD=<AISTHRSHLD>],[SABIT=<SABIT>],[IMPEDANCE=<IMPEDANCE>], [BITSFAC=<BITSFAC>],[ADMSSM=<ADMSSM>]:[<PST>]" ;

RTRV-COND-BITS:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,]; Retrieves the standing condition on BITS. Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>], [<OCRTM>],,,[<DESC>]" ;

RTRV-COND-SYNCN:[<TID>]:<AID>:<CTAG>::[<TYPEREQ>][,,,]; Retrieves the synchronization condition. Output format: SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>], [<OCRDAT>],[<OCRTM>],,,[<DESC>]" ;

RTRV-NE-SYNCN:[<TID>]:[<AID>]:<CTAG>[::::]; Retrieves the synchronization attributes of the NE. Output format: SID DATE TIME M CTAG COMPLD ":[<AID>]:[TMMD=<TMMD>,][SSMGEN=<SSMGEN>],[QRES=<QRES>], [RVRTV=<RVRTV>],[RVTM=<RVTM>]" ;

RTRV-SYNCN:[<TID>]:<AID>:<CTAG>[::::]; Retrieves the synchronization reference list used to determine the sources for the NE's reference clock and the BITS output clock. Output format: SID DATE TIME M CTAG COMPLD "<AID>:<REF>,<REFVAL>,[<QREF>],[<STATUS>],[<PROTECTSTATUS>]" ;

18 System

Table 18 System 

ALW-MSG-ALL:[<TID>]:[<AID>]:<CTAG>[::,,]; Allows REPT ALM and REPT EVT autonomous messages to be transmitted.

DLT-ROUTE:[<TID>]::<CTAG>::<DESTIP>; Deletes the static routes.

DLT-ROUTE-GRE:[<TID>]::<CTAG>:::IPADDR=<IPADDR>,IPMASK=<IPMASK>, NSAP=<NSAP>; Deletes a GRE tunnel.

DLT-TADRMAP:[<TID>]::<CTAG>:::[TIDNAME=<TIDNAME>],[ADDRTYPE=<ADDRTYPE>]; Deletes an entry in the TADRMAP table.

DLT-TRAPTABLE:[<TID>]:<AID>:<CTAG>; Deletes SNMP trap destination entry. Entering ALL will delete the whole table.

DLT-TUNNEL-FIREWALL:[<TID>]::<CTAG>:::[SRCADDR=<SRCADDR>], [SRCMASK=<SRCMASK>],[DESTADDR=<DESTADDR>],[DESTMASK=<DESTMASK>]; Deletes a firewall tunnel.

DLT-TUNNEL-PROXY:[<TID>]::<CTAG>:::[SRCADDR=<SRCADDR>], [SRCMASK=<SRCMASK>],[DESTADDR=<DESTADDR>],[DESTMASK=<DESTMASK>]; Deletes a proxy tunnel.

ED-DAT:[<TID>]::<CTAG>::[<DATE>],[<TIME>]; Edits the date and the time.

ED-NE-GEN:[<TID>]::<CTAG>:::[NAME=<NAME>],[IPADDR=<IPADDR>], [IPMASK=<IPMASK>],[DEFRTR=<DEFRTR>],[IIOPPORT=<IIOPPORT>], [NTP=<NTP>],[ISPROXYSERVER=<ISPROXYSERVER>],[ISFIREWALL=<ISFIREWALL>], [SUPPRESSIP=<SUPPRESSIP>],[MODE=<MODE>]; Edits the general node attributes of an NE.

ED-NE-PATH:[<TID>]::<CTAG>:::[PDIP=<PDIP>],[XCMODE=<XCMODE>]; Edits path related parameters for the NE-wide basis.

ED-TRAPTABLE:[<TID>]:<AID>:<CTAG>:::COMMUNITY=<COMMUNITY>, [TRAPPORT=<TRAPPORT>],[TRAPVER=<TRAPVER>]; Modifies a trap destination entry identified by a specific trap destination address.

ENT-ROUTE:[<TID>]::<CTAG>::<DESTIP>,<IPMASK>,<NXTHOP>,<COST>; Creates the static route.

ENT-ROUTE-GRE:[<TID>]::<CTAG>:::IPADDR=<IPADDR>,IPMASK=<IPMASK>, NSAP=<NSAP>,[COST=<COST>]; Creates a GRE tunnel.

ENT-TADRMAP:[<TID>]::<CTAG>:::[TIDNAME=<TIDNAME>],[IPADDR=<IPADDR>], [PORT=<PORT>],[ENCODING=<ENCODING>],[NSAP=<NSAP>]; Creates an entry in the TADRMAP table which maps the TID of the subtending NEs to their addresses.

ENT-TRAPTABLE:[<TID>]:<AID>:<CTAG>::COMMUNITY=<COMMUNITY>, [TRAPPORT=<TRAPPORT>],[TRAPVER=<TRAPVER>]; Provisions a SNMP trap destination and its associated community, UDP port and SNMP version.

ENT-TUNNEL-FIREWALL:[<TID>]::<CTAG>:::[SRCADDR=<SRCADDR>], [SRCMASK=<SRCMASK>],[DESTADDR=<DESTADDR>],[DESTMASK=<DESTMASK>]; Creates a firewall tunnel.

ENT-TUNNEL-PROXY:[<TID>]::<CTAG>:::[SRCADDR=<SRCADDR>], [SRCMASK=<SRCMASK>],[DESTADDR=<DESTADDR>],[DESTMASK=<DESTMASK>]; Creates a proxy tunnel.

INH-MSG-ALL:[<TID>]:[<AID>]:<CTAG>[::,,]; Inhibits REPT ALM and REPT EVT autonomous messages from being transmitted.

INIT-SYS:[<TID>]:<AID>:<CTAG>::[<CMDMDE=CMDMODE>]; Initializes the specified card and its associated subsystem(s).

RTRV-HDR:[<TID>]::<CTAG>; Retrieves the header of a TL1 response message.

RTRV-INV:[<TID>]:<AID>:<CTAG>[::::]; Retrieves a listing of the equipment inventory. Output format: SID DATE TIME M CTAG COMPLD "<AID>,<AIDTYPE>::[PN=<PN>],[HWREV=<HWREV>],[FWREV=<FWREV>],[SN=<SN>], [CLEI=<CLEI>],[TWL1=<TWL>],[PLUGINVENDORID=<PLUGINVENDORID>], [PLUGINPN=<PLUGINPN>],[PLUGINHWREV=<PLUGINHWREV>], [PLUGINFWREV=<PLUGINFWREV>],[PLUGINSN=<PLUGINSN>], [ILOSSREF=<ILOSSREF>],[PID=<PID>],[VID=<VID>],[FPGA=<FPGA>], [VENDORID=<VENDORID>]" ;

RTRV-NE-GEN:[<TID>]::<CTAG>; Retrieves the general NE attributes. Output format: SID DATE TIME M CTAG COMPLD "[IPADDR=<IPADDR>],[IPMASK=<IPMASK>],[DEFRTR=<DEFRTR>], [IIOPPORT=<IIOPPORT>],[NTP=<NTP>],[ETHIPADDR=<ETHIPADDR>], [ETHIPMASK=<ETHIPMASK>],[NAME=<NAME>],[SWVER=<SWVER>],[LOAD=<LOAD>], [PROTSWVER=<PROTSWVER>],[PROTLOAD=<PROTLOAD>],[DEFDESC=<DEFDESC>], [PLATFORM=<PLATFORM>],[SECUMODE=<SECUMODE>],[SUPPRESSIP=<SUPPRESSIP>]" ;

RTRV-NE-PATH:[<TID>]::<CTAG>[::::]; Retrieves the general NE attributes. Output format: SID DATE TIME M CTAG COMPLD "[PDIP=<PDIP>],[XCMODE=<XCMODE>]" ;

RTRV-NETYPE:[<TID>]::<CTAG>; Retrieves the equipment-related information of an NE. Output format: SID DATE TIME M CTAG COMPLD "<VENDOR>,<MODEL>,<NETYPE>,<SW_ISSUE>" ;

RTRV-ROUTE:[<TID>]::<CTAG>::[<DESTIP>],[<IPMASK>],[<NXTHOP>],[<COST>]; Retrieves static routes. Output format: SID DATE TIME M CTAG COMPLD ",:<DESTIP>,<IPMASK>,<NXTHOP>,<COST>" ;

RTRV-ROUTE-GRE:[<TID>]::<CTAG>[::::]; Retrieves the existing GRE tunnels. Output format: SID DATE TIME M CTAG COMPLD ",:IPADDR=<IPADDR>,IPMASK=<IPMASK>,NSAP=<NSAP>,COST=<COST>" ;

RTRV-TADRMAP:[<TID>]:[<AID>]:<CTAG>[:::MODE=<MODE>]; Retrieves the contents of the TADRMAP table. Output format: SID DATE TIME M CTAG COMPLD "[TID=<TID>],[IP ADDRESS =<IPADDRESS>],[NSAP=<NSAP>]" ;

RTRV-TOD:[<TID>]::<CTAG>; Retrieves the system date and time at the instant the command is executed. Output format: SID DATE TIME M CTAG COMPLD "<YEAR>,<MONTH>,<DAY>,<HOUR>,<MINUTE>,<SECOND>, <DIFFERENCE>:<TMTYPE>" ;

RTRV-TRAPTABLE:[<TID>]:[<AID>]:<CTAG>; Retrieves a trap destination entry based on the destination address. Output format: SID DATE TIME M CTAG COMPLD "<DEST>,<TRAPPORT>,<COMMUNITY>,<SNMPVERSION>" ;

RTRV-TUNNEL-FIREWALL:[<TID>]::<CTAG>; Retrieves the contents of the firewall table. Output format: SID DATE TIME M CTAG COMPLD "[SRC ADDR=<SRCADDR>],[SRC MASK=<SRCMASK>],[DEST ADDR=<DESTADDR>], [DEST MASK=<DESTMASK>]" ;

RTRV-TUNNEL-PROXY:[<TID>]::<CTAG>; Retrieves the contents of the proxy tunnel table. Output format: SID DATE TIME M CTAG COMPLD "[SRC ADDR=<SRCADDR>],[SRC MASK=<SRCMASK>],[DEST ADDR=<DESTADDR>], [DEST MASK=<DESTMASK>]" ;

SET-TOD:[<TID>]::<CTAG>::<YEAR>,<MONTH>,<DAY>,<HOUR>,<MINUTE>, <SECOND>,[<DIFFERENCE>][:DST=<DST>]; Sets the system date and time for the NE.

19 Troubleshooting and Test Access

Table 19 Troubleshooting and Test Access 

CHG-ACCMD-<MOD_TACC>:[<TID>]:<TAP>:<CTAG>::<MD>; Changes the test access mode for the circuit being tested.

CONN-TACC-<MOD_TACC>:[<TID>]:<SRC>:<CTAG>::<TAP>:MD=<MD>; Connects the VC or VT defined by AID to the VC specified by the test access point (TAP) number. Output format: SID DATE TIME M CTAG COMPLD "<TAP>" ;

DISC-TACC:[<TID>]:<TAP>:<CTAG>; Disconnects the TAP and puts the connection back to its original state.

OPR-LPBK-<MOD2>:[<TID>]:<AID>:<CTAG>::[<LOCATION>],,,[<LPBKTYPE>]; Operates a signal loopback on an input/output (I/O) card or on a cross-connect.

RLS-LPBK-<MOD2>:[<TID>]:<SRC>:<CTAG>::[<LOCATION>],,,[<LPBKTYPE>]; Releases a signal loopback on an I/O card or on a cross-connect.

RTRV-PTHTRC-<PATH>:[<TID>]:<SRC>:<CTAG>::[<MSGTYPE>][:<LSTM>]; Instructs an SDH NE to retrieve the contents of the SDH path trace message. Output format: SID DATE TIME M CTAG COMPLD "<TRACMSG>" ;

RTRV-TACC:[<TID>]:<TAP>:<CTAG>; Retrieves details associated with a TAP. Output format: SID DATE TIME M CTAG COMPLD "<TAP>:<TACC_AIDA>,<TACC_AIDB>,[<MD>],[<CROSSCONNECTID1>], <AIDUNIONID>,<PATHWIDTH>" ;

20 VCAT

Table 20 VCAT 

DLT-VCG:[<TID>]:<SRC>:<CTAG>:::[CMDMDE=<CMDMDE>][:]; Deletes a virtual concatenated group (VCG) object.

ED-VCG:[<TID>]:<SRC>:<CTAG>:::[TXCOUNT=<TXCOUNT>],[NAME=<NAME>]; Edits the attributes of a VCG.

ENT-VCG:[<TID>]:<SRC>:<CTAG>:::TYPE=<TYPE>,TXCOUNT=<TXCOUNT>,[CCT=<CCT>], [LCAS=<LCAS>],[BUFFERS=<BUFFERS>],[NAME=<NAME>]; Creates a VCG object.

RTRV-VCG:[<TID>]:<SRC>:<CTAG>[::::]; Retrieves all the attributes provisioned for a VCG. Output format: SID DATE TIME M CTAG COMPLD "<SRC>::TYPE=<TYPE>,TXCOUNT=<TXCOUNT>,CCT=<CCT>,[LCAS=<LCAS>], [BUFFERS=<BUFFERS>],[NAME=<NAME>]:<PST>" ;