Table Of Contents

RST Commands

20.1  RST-<MOD2>

20.2  RST-EQPT

RST Commands

---

This chapter provides RST (restore) commands for the Cisco ONS 15454 SDH.

20.1  RST-<MOD2>

Restore (10GFC, 10GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, CLNT, D1VIDEO, DS3I, DV6000, E1, E3, E4, ESCON, ETRCLO, FSTE, G1000, GFPOS, GIGE, HDTV, ISC1, STM4, STM64, STM1, STM16, OCH, OMS, OTS, POS, STM1E, VC3, VC44C, VC38C, VC464C, VC48C, STS36C, VC4, VC416C, VC42C, VC43C, VC11, VC12)

Usage Guidelines

This command provisions a facility in service.

See Table 27-1 on page 27-1 for supported modifiers by platform.

Category

Facility

Security

Maintenance

Related Commands

DLT-<MOD1PAYLOAD> DLT-FFP-<MOD2DWDMPAYLOAD> DLT-FFP-<STM_TYPE> ED-<MOD1FCPAYLOAD> ED-<MOD1FICONPAYLOAD> ED-<MOD2DWDMPAYLOAD> ED-<STM_TYPE> ED-ALS ED-DS3I ED-E1/ED-E3/ED-E4 ED-FAC ED-FFP-<MOD2DWDMPAYLOAD> ED-FFP-<STM_TYPE> ED-FSTE ED-G1000 ED-GFP ED-HDLC ED-STM1E ENT-<MOD1PAYLOAD> ENT-FFP-<MOD2DWDMPAYLOAD> ENT-FFP-<STM_TYPE> INIT-REG-<MOD2> OPR-ALS OPR-LPBK-<MOD2> OPR-PROTNSW-<MOD2DWDMPAYLOAD> OPR-PROTNSW-<STM_TYPE> REPT PM <MOD2> RLS-LPBK-<MOD2> RLS-PROTNSW-<MOD2DWDMPAYLOAD>

RLS-PROTNSW-<STM_TYPE> RMV-<MOD2> RTRV-<MOD1FCPAYLOAD> RTRV-<MOD1FICONPAYLOAD> RTRV-<MOD2DWDMPAYLOAD> RTRV-<STM_TYPE> RTRV-10GIGE RTRV-ALMTH-<MOD2> RTRV-ALS RTRV-DS3I RTRV-E1/RTRV-E3/RTRV-E4 RTRV-FAC RTRV-FFP-<MOD2DWDMPAYLOAD> RTRV-FFP-<STM_TYPE> RTRV-FSTE RTRV-G1000 RTRV-GFP RTRV-GIGE RTRV-HDLC RTRV-PM-<MOD2> RTRV-PMSCHED-<MOD2> RTRV-POS RTRV-PROTNSW-<MOD2DWDMPAYLOAD> RTRV-PROTNSW-<STM_TYPE> RTRV-STM1E RTRV-TH-<MOD2> SCHED-PMREPT-<MOD2> SET-ALMTH-<MOD2> SET-TH-<MOD2>

Input Format

RST-<MOD2>:[<TID>]:<AID>:<CTAG>::::[<PST>[,<SST>]];

Input Example

RST-E1:CISCO:FAC-1-1:1::::UNLOCKED,AUTOMATICINSERVICE;

Input Parameters

Table 20-1 RST-<MOD2> Input Parameters 

Parameter and Values	Description
AID	Access identifier from the "25.1  ALL" section on page 25-1
PST	Primary state Parameter type is PST—indicates the current overall service condition of an entity
•Unlocked	In service
•Locked	Out of service
SST	Secondary state Parameter type is SST—provides additional information pertaining to PST and PSTQ
•AutomaticInService	Automatic in service
•Disabled	Disabled
•Loopback	Loopback
•MismatchofEquipmentAlarm	Mismatch of equipment and attributes
•Maintenance	Maintenance mode
•OutOfGroup	Out of group
•SoftwareDownload	Software downloading
•Unassigned	Unassigned
•NotInstalled	Unequipped

20.2  RST-EQPT

Restore Equipment

Usage Guidelines

This command provisions equipment into the In Service state from the Maintenance state.

---

Note Only applicable to equipment that is in transition from the Maintenance state to the In-Service state.

---

Category

Equipment

Security

Maintenance

Related Commands

ALW-SWDX-EQPT ALW-SWTOPROTN-EQPT ALW-SWTOWKG-EQPT CHG-EQPT DLT-EQPT ED-EQPT ENT-EQPT INH-SWDX-EQPT INH-SWTOPROTN-EQPT INH-SWTOWKG-EQPT REPT ALM EQPT REPT EVT EQPT

REPT RMV EQPT REPT RST EQPT RMV-EQPT RTRV-ALM-EQPT RTRV-ALMTH-EQPT RTRV-COND-EQPT RTRV-EQPT SET-ALMTH-EQPT SW-DX-EQPT SW-TOPROTN-EQPT SW-TOWKG-EQPT

Input Format

RST-EQPT:[<TID>]:<AID>:<CTAG>[::];

Input Example

RST-EQPT:CISCO:SLOT-1:1;

Input Parameters

Table 20-2 RST-EQPT Input Parameters 

Parameter and Values	Description
AID	Access identifier from the "25.1.10  EQPT" section on page 25-15