この製品のマニュアルセットは、偏向のない言語を使用するように配慮されています。このマニュアルセットでの偏向のない言語とは、年齢、障害、性別、人種的アイデンティティ、民族的アイデンティティ、性的指向、社会経済的地位、およびインターセクショナリティに基づく差別を意味しない言語として定義されています。製品ソフトウェアのユーザーインターフェイスにハードコードされている言語、RFP のドキュメントに基づいて使用されている言語、または参照されているサードパーティ製品で使用されている言語によりドキュメントに例外が存在する場合があります。シスコのインクルーシブランゲージに対する取り組みの詳細は、こちらをご覧ください。
このドキュメントは、米国シスコ発行ドキュメントの参考和訳です。リンク情報につきましては、日本語版掲載時点で、英語版にアップデートがあり、リンク先のページが移動/変更されている場合がありますことをご了承ください。あくまでも参考和訳となりますので、正式な内容については米国サイトのドキュメントを参照ください。
この章の内容は、次のとおりです。
このタスクを実行するには、admin 権限でログインする必要があります。
次に、2 台の未使用の物理ドライブにまたがる新しい仮想ドライブの作成方法を示します。
Server# scope chassis
Server /chassis # scope storageadapter SLOT-3
Server /chassis/storageadapter # create-virtual-drive
Please enter RAID level
0, 1, 5, 10, 50 --> 1
Please choose from the following 10 unused physical drives:
ID Size(MB) Model Interface Type
1 571776 SEAGATE SAS HDD
2 571776 SEAGATE SAS HDD
4 571776 SEAGATE SAS HDD
5 428672 SEAGATE SAS HDD
6 571776 SEAGATE SAS HDD
7 571776 SEAGATE SAS HDD
8 571776 SEAGATE SAS HDD
9 428672 SEAGATE SAS HDD
10 571776 SEAGATE SAS HDD
11 953344 SEAGATE SAS HDD
Specify physical disks for span 0:
Enter comma-separated PDs from above list--> 1,2
Please enter Virtual Drive name (15 characters maximum)--> test_v_drive
Please enter Virtual Drive size in MB, GB, or TB
Example format: '400 GB' --> 10 GB
Optional attribute:
stripsize: defaults to 64K Bytes
0: 8K Bytes
1: 16K Bytes
2: 32K Bytes
3: 64K Bytes
4: 128K Bytes
5: 256K Bytes
6: 512K Bytes
7: 1024K Bytes
Choose number from above options or hit return to pick default--> 2
stripsize will be set to 32K Bytes (6 and 'strip-size\:32k')
Disk Cache Policy: defaults to Unchanged
0: Unchanged
1: Enabled
2: Disabled
Choose number from above options or hit return to pick default--> 0
Disk Cache Policy will be set to Unchanged (0 and 'disk-cache-policy\:unchanged' )
Read Policy: defaults to No Read Ahead
0: No Read Ahead
1: Always
Choose number from above options or hit return to pick default--> 0
Read Policy will be set to No Read Ahead (0 and 'read-policy\:no-read-ahead')
Write Policy: defaults to Write Through
0: Write Through
1: Write Back Good BBU
2: Always Write Back
Choose number from above options or hit return to pick default--> 0
Write Policy will be set to Write Through (0 and 'write-policy\:write-through')
IO Policy: defaults to Direct I/O
0: Direct I/O
1: Cached I/O
Choose number from above options or hit return to pick default--> 0
IO Policy will be set to Direct I/O (0 and 'io-policy\:direct-io')
Access Policy: defaults to Read Write
0: Read Write
1: Read Only
2: Blocked
Choose number from above options or hit return to pick default--> 0
Access Policy will be set to Read Write (0 and 'access-policy\:read-write')
Enable SED security on virtual drive (and underlying drive group)?
Enter y or n--> y
Virtual drive and drive group will be secured
New virtual drive will have the following characteristics:
- Spans: '[1.2]'
- RAID level: '1'
- Name: 'test_v_drive'
- Size: 10 GB
- stripsize: 32K Bytes
- Disk Cache Policy: Unchanged
- Read Policy: No Read Ahead
- Write Policy: Write Through
- IO Policy: Direct I/O
- Access Policy: Read Write
- Encryption: FDE
OK? (y or n)--> y
Server /chassis/storageadapter # show virtual-drive
Virtual Drive Health Status Name Size RAID Level Boot Drive
------------- -------------- -------------------- ---------------- ---------- ---------- ----------
0 Good Optimal 150528 MB RAID 0 false
1 Good Optimal 20480 MB RAID 0 true
2 Good Optimal 114140 MB RAID 0 false
3 Good Optimal test_v_drive 10000 MB RAID 1 false
4 Good Optimal new_from_test 500 MB RAID 1 false
Server /chassis/storageadapter #
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # carve-virtual-drive |
この時点で、使用する仮想ドライブに関する情報、新しい仮想ドライブのサイズと書き込みポリシーに関する情報の入力を求めるプロンプトが表示されます。プロンプトごとに適切な情報を入力します。 仮想ドライブの情報の指定が完了したら、情報が正しいことの確認を求めるプロンプトが表示されます。確認する場合は y(yes)を入力し、操作をキャンセルする場合は n(no)を入力します。 |
ステップ 4 | Server /chassis/storageadapter # show virtual-drive |
既存の仮想ドライブが表示されます。 |
次に、既存の RAID 1 ドライブ グループ内の未使用のスペースから新しい仮想ドライブを分割する例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # carve-virtual-drive < Fetching virtual drives...> ID Name RL VDSize MaxPossibleSize PD(s) ---------------------------------------------------------------- 0 RAID0_12 0 100 MB Unknown 1,2 Please choose from the above list the virtual drive number whose space the new virtual drive will share--> 0 New virtual drive will share space with VD 0 Please enter Virtual Drive name (15 characters maximum)--> test_v_drive Please enter Virtual Drive size in MB, GB, or TB (maximum: Unknown) Example format: '400 GB' --> 10 GB Optional attributes: stripsize: defaults to 64K Bytes 0: 8K Bytes 1: 16K Bytes 2: 32K Bytes 3: 64K Bytes 4: 128K Bytes 5: 256K Bytes 6: 512K Bytes 7: 1024K Bytes Choose number from above options or hit return to pick default--> 0 stripsize will be set to 8K Bytes (4 and 'strip-size\:8k') Disk Cache Policy: defaults to Unchanged 0: Unchanged 1: Enabled 2: Disabled Choose number from above options or hit return to pick default--> 0 Disk Cache Policy will be set to Unchanged (0 and 'disk-cache-policy\:unchanged') Read Policy: defaults to No Read Ahead 0: No Read Ahead 1: Always Choose number from above options or hit return to pick default--> 0 Read Policy will be set to No Read Ahead (0 and 'read-policy\:no-read-ahead') Write Policy: defaults to Write Through 0: Write Through 1: Write Back Good BBU 2: Always Write Back Choose number from above options or hit return to pick default--> 0 Write Policy will be set to Write Through (0 and 'write-policy\:write-through') IO Policy: defaults to Direct I/O 0: Direct I/O 1: Cached I/O Choose number from above options or hit return to pick default--> 0 IO Policy will be set to Direct I/O (0 and 'io-policy\:direct-io') Access Policy: defaults to Read Write 0: Read Write 1: Read Only 2: Blocked Choose number from above options or hit return to pick default--> 0 Access Policy will be set to Read Write (0 and 'access-policy\:read-write') New virtual drive will have the following characteristics: - It will share space with virtual drive 0 - Name: 'amit' - Size: 10 GB - stripsize: 8K Bytes - Disk Cache Policy: Unchanged - Read Policy: No Read Ahead - Write Policy: Write Through - IO Policy: Direct I/O - Access Policy: Read Write OK? (y or n)--> y Server /chassis/storageadapter # show virtual-drive Virtual Drive Health Status Name Size RAID Level Boot Drive ------------- -------------- -------------------- ---------------- ---------- ---------- ---------- 0 Good Optimal 150528 MB RAID 0 false 1 Good Optimal 20480 MB RAID 0 true 2 Good Optimal 114140 MB RAID 0 false 3 Good Optimal test_v_drive 10000 MB RAID 1 false 4 Good Optimal new_from_test 500 MB RAID 1 false Server /chassis/storageadapter #
コマンドまたはアクション | 目的 | |||
---|---|---|---|---|
ステップ 1 | Server # scopechassis |
シャーシ コマンド モードを開始します。 | ||
ステップ 2 | Server /chassis # scopestorageadapter slot ID |
装着されているストレージ カードに対してコマンド モードを開始します。 | ||
ステップ 3 | Server /chassis/storageadapter # scopevirtual-drive drive-number |
指定された仮想ドライブのコマンド モードを開始します。 | ||
ステップ 4 | Server /chassis/storageadapter/virtual-drive # set-transport-ready {include-all | exclude-all | include-dhsp} |
仮想ドライブをトランスポート可能に設定し、選択したプロパティを割り当てます。 処理の確認を求めるプロンプトが表示されます。確認のために y を入力します。
| ||
ステップ 5 | Server /chassis/storageadapter/virtual-drive # show detail | (任意)
変更した仮想ドライブのプロパティを表示します。 |
次に、仮想ドライブ 5 をトランスポート可能に設定する例を示します。
Server # scope chassis Server /chassis # scope storageadapter SLOT-HBA Server /chassis/storageadapter # scope virtual-drive 5 Server /chassis/storageadapter/virtual-drive # set-transport-ready exclude-all Since they belong to same drive group, all these virtual drives will be set to Transport Ready - 0 Are you sure you want to proceed?[y|N]y Server /chassis/storageadapter/virtual-drive # show detail Virtual Drive 0: Health: Good Status: Optimal Visibility : Visible Name: RAID0_124_RHEL Size: 2858160 MB Physical Drives: 1, 2, 4 RAID Level: RAID 0 Boot Drive: false FDE Capable: 0 FDE Enabled: 0 Target ID: 0 Strip Size: 64 KB Drives Per Span: 3 Span Depth: 1 Access Policy: Transport Ready Cache Policy: Direct Read Ahead Policy: None Requested Write Cache Policy: Write Through Current Write Cache Policy: Write Through Disk Cache Policy: Unchanged Auto Snapshot: false Auto Delete Oldest: true Allow Background Init: true Server /chassis/storageadapter/virtual-drive #
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server # scopechassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scopestorageadapter slot ID |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # scopevirtual-drive drive-number |
指定された仮想ドライブのコマンド モードを開始します。 |
ステップ 4 | Server /chassis/storageadapter/virtual-drive # clear-transport-ready |
これにより、選択したトランスポート可能な仮想ドライブが元の状態に戻されます。 処理の確認を求めるプロンプトが表示されます。確認のために y を入力します。 |
ステップ 5 | Server /chassis/storageadapter/virtual-drive # show detail | (任意)
変更した仮想ドライブのプロパティを表示します。 |
次の例は、選択したトランスポート可能な仮想ドライブを元の状態に戻す方法を示しています。
Server # scope chassis Server /chassis # scope server 1 Server /chassis # scope storageadapter SLOT-HBA Server /chassis/storageadapter # scope virtual-drive 5 Server /chassis/storageadapter/virtual-drive # clear-transport-ready Since they belong to same drive group, all these virtual drives will be moved out of Transport Ready - 0 Are you sure you want to proceed?[y|N]y Server /chassis/storageadapter/virtual-drive # show detail Virtual Drive 0: Health: Good Status: Optimal Visibility : Visible Name: RAID0_124_RHEL Size: 2858160 MB Physical Drives: 1, 2, 4 RAID Level: RAID 0 Boot Drive: false FDE Capable: 0 FDE Enabled: 0 Target ID: 0 Strip Size: 64 KB Drives Per Span: 3 Span Depth: 1 Access Policy: Read-Write Cache Policy: Direct Read Ahead Policy: None Requested Write Cache Policy: Write Through Current Write Cache Policy: Write Through Disk Cache Policy: Unchanged Auto Snapshot: false Auto Delete Oldest: true Allow Background Init: true Server /chassis/storageadapter/virtual-drive #
別のコントローラで以前に設定されている 1 つ以上の物理ドライブがサーバにインストールされると、それらは外部設定として識別されます。コントローラにこれらの外部設定をインポートできます。
これらのシナリオに外部設定をインポートするには、サーバ 2 のコントローラ セキュリティをローカル キー管理からリモート キー管理に変更し、サーバ 1 の KMIP が設定されている同じクラスタの同じ KMIP サーバを使用します。
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 |
---|
次に、スロット 3 にある MegaRAID コントローラのすべての外部設定をインポートする例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # import-foreign-config Are you sure you want to import all foreign configurations on this controller? Enter 'yes' to confirm -> yes Server /chassis/storageadapter #
セキュアなドライブ グループをホストする物理ドライブのセットが別のサーバまたはコントローラ(または、それらが存在しない間にセキュリティ キーが変更された同じコントローラ)に挿入されると、それらは外部設定になります。これらは保護されているため、外部設定をインポートする前にロックを解除する必要があります。外部設定ドライブのロックを解除する方法を次の手順で説明します。
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # unlock-foreign-configuration |
プロンプトで、セキュリティ キーを入力し、確認プロンプトで yes と入力します。 |
ステップ 4 | Server /chassis/storageadapter # scope physical-drive 2 | (任意)
物理ドライブ コマンド モードを開始します。 |
ステップ 5 | Server /chassis/storageadapter/physicsl-drive # show detail | (任意)
ロックが解除された外部ドライブのステータスが表示されます。 |
次に、外部設定ドライブのロックを解除する例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # unlock-foreign-configuration Please enter the security key to unlock the foreign configuration -> testSecurityKey Server /chassis/storageadapter # import-foreign-config Are you sure you want to import all foreign configurations on this controller? Enter 'yes' to confirm -> yes Server /chassis/storageadapter # scope physical-drive 2 Server /chassis/storageadapter/physical-drive # show detail Physical Drive Number 2: Controller: SLOT-HBA Health: Good Status: Online . . FDE Capable: 1 FDE Enabled: 1 FDE Secured: 1 FDE Locked: 0 FDE locked foreign config: 0 Server /chassis/storageadapter/physical-drive #
このタスクでは、コントローラのすべての外部設定をクリアします。また、外部設定をホスティングしているすべての物理ドライブからすべての設定情報が削除されます。このアクションは元に戻せません。
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 |
---|
次に、スロット 3 にある MegaRAID コントローラのすべての外部設定をクリアする例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # clear-foreign-config Are you sure you want to clear all foreign configurations on this controller? All data on the drive(s) will be lost. Enter 'yes' to confirm -> yes Server /chassis/storageadapter #
(注) | 一部の UCS C シリーズ サーバでのみ Just a Bunch Of Disks(JBOD)を有効にできます。 |
コマンドまたはアクション | 目的 |
---|
次に、選択したコントローラに対して JBOD モードをイネーブルにする例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # enable-jbod-mode Are you sure you want to enable JBOD mode? Enter 'yes' to confirm -> yes Server/chassis/storageadapter # show settings PCI Slot SLOT-3: Info Valid: Yes Enable JBOD Mode: true
(注) | このオプションを使用できるのは一部の UCS C シリーズ サーバだけです。 |
選択したコントローラに対して JBOD モードをイネーブルにする必要があります。
コマンドまたはアクション | 目的 |
---|
次に、選択したコントローラの JBOD モードをディセーブルにする例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # disable-jbod-mode Are you sure you want to disable JBOD mode? Enter 'yes' to confirm -> yes Server/chassis/storageadapter # show settings PCI Slot SLOT-3: Info Valid: Yes Enable JBOD Mode: false
このタスクでは、コントローラのブート ドライブ設定がクリアされます。このアクションは元に戻せません。
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 |
---|
次に、スロット 3 にある MegaRAID コントローラ上のブート ドライブ設定をクリアする例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # clear-boot-drive Are you sure you want to clear the controller's boot drive? Enter 'yes' to confirm -> yes Server /chassis/storageadapter #
物理ドライブが JBOD である場合にのみ、そのドライブでセキュリティをイネーブルにできます。次に、JBOD でセキュリティをイネーブルにする手順を示します。
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # scope physical-drive 2 |
物理ドライブ コマンド モードを開始します。 |
ステップ 4 | Server /chassis/storageadapter # enable-security-on-jbod |
確認プロンプトに yes と入力します。 JBOD でセキュリティをイネーブルにします。 |
ステップ 5 | Server /chassis/storageadapter/physicsl-drive # show detail | (任意)
物理ドライブの詳細が表示されます。 |
次に、JBOD でセキュリティをイネーブルにする例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 savbu-stordev-dn1-2-cimc /chassis/storageadapter # scope physical-drive 2 server /chassis/storageadapter/physical-drive # enable-security-on-jbod Are you sure you want to enable security on this JBOD? NOTE: this is not reversible! Enter 'yes' to confirm -> yes server /chassis/storageadapter/physical-drive # show detail Physical Drive Number 2: . . Status: JBOD . . FDE Capable: 1 FDE Enabled: 1 FDE Secured: 1 server /chassis/storageadapter/physical-drive #
セキュアなドライブをクリアすると、FDE ドライブはセキュアなドライブから非セキュアなドライブに変換されます。このアクションを実行するには、物理ドライブのステータスを [未設定良好(Unconfigured Good)] にする必要があります。これによって、物理ドライブ上のデータが削除されます。セキュアな SED 物理ドライブをクリアする方法を次の手順で説明します。
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # scope physical-drive 2 |
物理ドライブ コマンド モードを開始します。 |
ステップ 4 | Server /chassis/storageadapter/physicsl-drive # clear-secure-drive |
確認プロンプトに yes と入力します。 これによって、セキュアな SED 物理ドライブがクリアされ、すべてのデータが失われます。 |
ステップ 5 | Server /chassis/storageadapter/physicsl-drive # show detail | (任意)
物理ドライブの詳細を表示します。 |
次に、SED 外部設定物理ドライブをクリアする例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # scope physical-drive 2 Server /chassis/storageadapter/physical-drive # clear-secure-drive Are you sure you want to erase all data from this physical drive? NOTE: this is not reversible! ALL DATA WILL BE LOST!! Enter 'yes' to confirm -> yes Server /chassis/storageadapter/physical-drive # show detail Physical Drive Number 2: Controller: SLOT-HBA Health: Good Status: Unconfigured Good . . FDE Capable: 1 FDE Enabled: 0 FDE Secured: 0 Server /chassis/storageadapter/physical-drive #
ロックされている外部設定フル ディスク暗号化ドライブを非セキュアなロックされていないドライブに変換します。これによって、物理ドライブ上のデータが削除されます。セキュアな SED 外部設定物理ドライブをクリアする方法を次の手順で説明します。
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # scope physical-drive 2 |
物理ドライブ コマンド モードを開始します。 |
ステップ 4 | Server /chassis/storageadapter/physicsl-drive # clear-secure-foreign-config-drive |
確認プロンプトに yes と入力します。 これによって、セキュアな SED 外部設定物理ドライブがクリアされ、すべてのデータが失われます。 |
ステップ 5 | Server /chassis/storageadapter/physicsl-drive # show detail | (任意)
物理ドライブの詳細を表示します。 |
次に、SED 外部設定物理ドライブをクリアする例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # scope physical-drive 2 Server /chassis/storageadapter/physical-drive # clear-secure-foreign-config-drive Are you sure you want to erase all data from this foreign-configuration physical drive? NOTE: this is not reversible! ALL DATA WILL BE LOST!! Enter 'yes' to confirm -> yes Server /chassis/storageadapter/physical-drive # show detail Physical Drive Number 2: Controller: SLOT-HBA Health: Good Status: Unconfigured Good . . FDE Capable: 1 FDE Enabled: 0 FDE Secured: 0 FDE Locked: 0 FDE Locked Foreign Config: 0 Server /chassis/storageadapter/physical-drive #
このタスクでは、コントローラのストレージ ファームウェア ログを取得して /var/log に配置します。これにより、テクニカル サポート データが要求された場合にこのログ データを確実に使用できるようになります。
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # get-storage-fw-log | |
ステップ 4 | Server /chassis/storageadapter # show detail |
取得プロセスのステータスを表示します。 コントローラのストレージ ファームウェア ログの取得には、2 ~ 4 分かかることがあります。このプロセスが完了するまで、テクニカル サポート データのエクスポートを開始しないでください。 |
次に、スロット 3 の MegaRAID コントローラのストレージ ファームウェア ログを取得する例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # get-storage-fw-log Server /chassis/storageadapter # show detail PCI Slot SLOT-3: TTY Log Status: In progress (8192 bytes fetched) Server /chassis/storageadapter # show detail PCI Slot SLOT-3: TTY Log Status: In progress (90112 bytes fetched) Server /chassis/storageadapter # show detail PCI Slot SLOT-3: TTY Log Status: Complete (172032 bytes fetched)
Cisco IMC は、自己暗号化ドライブ(SED)をサポートしています。ドライブ内の特別なハードウェアがリアルタイムで入力データを暗号化し、出力データを復号します。この機能は、フル ディスク暗号化(FDE)とも呼ばれます。
ドライブ上のデータは、ドライブに入力される際に暗号化され、出力される際に復号されます。ただし、ドライブをロックしている場合は、データを取得するためにセキュリティ キーは必要ありません。
ドライブがロックされると、暗号化キーが内部で作成され保存されます。このドライブに保存されているすべてのデータは、そのキーを使用して暗号化され、暗号化された形式で保存されます。データをこのように保存すると、データを非暗号化してドライブから取得するためにセキュリティ キーが必要になります。ドライブのロックを解除すると、その暗号化キーが削除され、保存されたデータは使用できなくなります。これは、Secure Erase と呼ばれます。FDE は、キー ID とセキュリティ キーで構成されます。
デュアル SIOC 環境でコントローラ セキュリティを設定する場合に考慮すべきシナリオ
(注) | デュアル SIOC 接続は一部のサーバでのみ使用できます。 |
コントローラ セキュリティは、個別に有効化、無効化、変更することができます。ただし、ローカルおよびリモート キー管理はサーバ上のすべてのコントローラに適用されます。したがって、キー管理モードの切り替えに関連するセキュリティ アクションは、慎重に実行する必要があります。両方のコントローラが保護されているシナリオにおいて、一方のコントローラを別のモードに切り替える場合は、もう一方のコントローラに対しても同じ操作を実行する必要があります。
次の 2 つのシナリオについて考えてください。
シナリオ 1:キー管理がリモートに設定されており、両方のコントローラが保護され、リモート キー管理を使用している。ローカル キー管理に切り替える場合は、各コントローラのキー管理を切り替えて、リモート キー管理を無効にします。
シナリオ 2:キー管理がローカルに設定されており、両方のコントローラが保護され、ローカル キー管理を使用している。リモート キー管理に切り替える場合は、リモート キー管理を有効にして、各コントローラのキー管理を切り替えます。
どちらかのコントローラのセキュリティ方式を変更しないままにすると、セキュア キー管理が「サポートされない設定(unsupported configuration)」状態になります。
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # enable-controller-security |
この時点で、セキュリティ キーを入力するように求められますが、希望するセキュリティ キーを入力することも、提案されているセキュリティ キーを使用することもできます。希望するセキュリティ キーを割り当てる場合は、プロンプトでそのセキュリティ キーを入力します。 提案されたセキュリティ キーを使用するか、希望のセキュリティ キーを使用するかによって、該当するプロンプトで y(yes)を入力して確認するか、n(no)を入力して操作をキャンセルします。 |
ステップ 4 | Server /chassis/storageadapter # show detail |
ストレージ ドライブの詳細が表示されます。 |
次に、コントローラでセキュリティをイネーブルにする例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # enable-controller-security Use generated key-id 'UCSC-MRAID12G_FHH18250010_1d85dcd3'? (y or n)--> y Use suggested security-key '6ICsmuX@oVB7e9wXt79qsTgp6ICsmuX@'? (y or n)--> n Enter security-key --> testSecurityKey Will use security-key 'testSecurityKey' Server /chassis/storageadapter show detail PCI Slot SLOT-HBA: <stuff deleted> Controller is Secured: 1 Server /chassis/storageadapter #
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # disable-controller-security |
確認のプロンプトが表示されます。 確認プロンプトで、yes と入力して確認するか、または n(no)を入力して操作をキャンセルします。 セキュリティ キーを入力するための別のプロンプトが表示されます。セキュリティ キーを入力します。 これにより、コントローラのセキュリティがディセーブルになります。 |
ステップ 4 | Server /chassis/storageadapter # show detail |
ストレージ ドライブの詳細が表示されます。 |
次に、コントローラでセキュリティをディセーブルにする例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # disable-controller-security Note: this operation will fail if any secured drives are present. Are you sure you want to disable security on this controller? Enter 'yes' to confirm -> yes Please enter the controller's security-key -> testSecurityKey savbu-stordev-dn1-2-cimc /chassis/storageadapter # show detail PCI Slot SLOT-HBA: <stuff deleted> Controller is Secured: 0 Server /chassis/storageadapter #
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # modify-controller-security |
この時点で、現在のセキュリティ キーを入力するように求められます。また、任意で、キー ID をリセットするかどうかを選択したり、新しいセキュリティ キーを選択することもできます。適切な情報を入力します。 確認プロンプトで、y(yes)と入力して確認するか、または n(no)を入力して操作をキャンセルします。 |
次に、コントローラのセキュリティ設定を変更する例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # modify-controller-security Please enter current security-key --> testSecurityKey Keep current key-id 'UCSC-MRAID12G_FHH18250010_1d85dcd3'? (y or n)--> n Enter new key-id: NewKeyId Will change key-id to 'NewKeyId' Keep current security-key? (y or n)--> y Server /chassis/storageadapter #
セキュリティ キーがわからない場合は、次の手順を使用すると、入力したセキュリティ キーがコントローラのセキュリティ キーと一致しているかどうかを確認できます。
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 |
---|
次に、コントローラのセキュリティ キーを確認する例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # verify-controller-security-key Please enter the security key to verify -> WrongSecurityKey verify-controller-security-key failed. Error: "r-type: RAID controller: SLOT-HBA command-status: Lock key from backup failed verification" savbu-stordev-dn1-2-cimc /chassis/storageadapter # savbu-stordev-dn1-2-cimc /chassis/storageadapter # verify-controller-security-key Please enter the security key to verify -> testSecurityKey Server /chassis/storageadapter #
このタスクによって、コントローラ セキュリティをローカル管理からリモート管理に切り替えたり、リモート管理からローカル管理に切り替えることができます。
コマンドまたはアクション | 目的 | |||
---|---|---|---|---|
ステップ 1 | Server # scopechassis |
シャーシ コマンド モードを開始します。 | ||
ステップ 2 | Server /chassis # scopestorageadapter Slot-ID |
ストレージ アダプタ コマンド モードを開始します。 | ||
ステップ 3 | Server /chassis/storageadapter # switch-to-local-key-mgmt |
プロンプトで y と入力します。
| ||
ステップ 4 | Server /chassis/server/storageadapter # key id |
プロンプトで新しい ID を入力します。ローカル キー管理に切り替えます。 |
次に、コントローラ セキュリティをリモート キー管理からローカル キー管理へ切り替える例を示します。
Server # scope chassis Server /chassis # scope storageadapter SLOT-HBA 1 Server /chassis/storageadapter # switch-to-local-key-mgmt Executing this command will require you to disable remote key management once switch is complete. Do you want to continue(y or n)?y Proceeding to switch to local key management. Enter new security-key: test Will change security-key to 'test' Switch to local key management complete on controller in SLOT-HBA. ***Remote key management needs to be disabled*** Please disable remote key management. Server /chassis/server/storageadapter #
リモート キー管理からローカル キー管理に切り替えた後、必ず KMIP セキュア キー管理を無効にしてください。
このタスクによって、コントローラ セキュリティをローカル管理からリモート管理に切り替えたり、リモート管理からローカル管理に切り替えることができます。
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server # scopechassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scopestorageadapter Slot-ID |
ストレージ アダプタ コマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # switch-to-remote-key-mgmt |
プロンプトで y と入力します。 |
ステップ 4 | Server /chassis/storageadapter # security id |
プロンプトでセキュリティ キーを入力します。リモート キー管理に切り替えます。 |
次に、コントローラ セキュリティをローカル キー管理からリモート キー管理へ切り替える例を示します。
Server # scope chassis Server /chassis # scope storageadapter SLOT-HBA 1 Server /chassis/server/storageadapter # switch-to-remote-key-mgmt Changing the security key requires existing security key. Please enter current security-key --> test Switch to remote key management complete on controller in SLOT-HBA. Server /chassis/server/storageadapter #
このタスクでは、ブートされたオペレーティング システムを実行するドライブを含む仮想ドライブを削除します。そのため、仮想ドライブを削除する前に、保持するデータをバック アップします。
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |||
---|---|---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 | ||
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 | ||
ステップ 3 | Server /chassis/storageadapter # scope virtual-drive drive-number |
指定された仮想ドライブのコマンド モードを開始します。 | ||
ステップ 4 | Server /chassis/storageadapter/virtual-drive # delete-virtual-drive |
処理の確認を求めるプロンプトが表示されます。確認のために yes を入力します。
|
次に、仮想ドライブ 3 を削除する例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # scope virtual-drive 3 Server /chassis/storageadapter/virtual-drive # delete-virtual-drive Are you sure you want to delete virtual drive 3? All data on the drive will be lost. Enter 'yes' to confirm -> yes Server /chassis/storageadapter/virtual-drive #
ドライブを初期化すると、仮想ドライブ上のすべてのデータが失われます。初期化を実行する前に、保存する仮想ドライブのデータをバックアップします。
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # scope virtual-drive drive-number |
指定された仮想ドライブのコマンド モードを開始します。 |
ステップ 4 | Server /chassis/storageadapter/virtual-drive # start-initialization |
指定した仮想ドライブを初期化します。 |
ステップ 5 | Server /chassis/storageadapter/virtual-drive # cancel-initialization |
(任意)指定した仮想ドライブの初期化をキャンセルします。 |
ステップ 6 | Server /chassis/storageadapter/physical-drive # get-operation-status | ドライブ上で処理中のタスクのステータスを表示します。 |
次に、高速初期化を使用して仮想ドライブ 3 を初期化する例を示します。
Server# scope chassis
Server /chassis # scope storageadapter SLOT-3
Server /chassis/storageadapter # scope virtual-drive 3
Server /chassis/storageadapter/virtual-drive # start-initialization
Are you sure you want to initialize virtual drive 3?
All data on the drive will be lost. Enter 'yes' to confirm -> yes
Fast (0) or full (1) initialization? -> 0
Server /chassis/storageadapter/virtual-drive # get-operation-status
progress-percent: 20%
elapsed -seconds: 30
operation-in-progress: initializing virtual drive
Server /chassis/storageadapter/virtual-drive #
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # scope virtual-drive drive-number |
指定された仮想ドライブのコマンド モードを開始します。 |
ステップ 4 | Server /chassis/storageadapter # set-boot-drive |
コントローラがこの仮想ドライブからブートするように指定します。 |
次に、コントローラが仮想ドライブ 3 からブートするように指定する例を示します。
Server# scope chassis
Server /chassis # scope storageadapter SLOT-3
Server /chassis/storageadapter # scope virtual-drive 3
Server /chassis/storageadapter/virtual-drive # set-boot-drive
Are you sure you want to set virtual drive 3 as the boot drive?
Enter 'yes' to confirm -> yes
Server /chassis/storageadapter/virtual-drive #
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server chassis /storageadapter # scope virtual-drive drive number |
指定された仮想ドライブのコマンド モードを開始します。 |
ステップ 4 | Server chassis /storageadapter /virtual-drive # modify-attributes |
現在のものとは異なるポリシーを選択するように求めるプロンプトが表示されます。 |
ステップ 5 | Server chassis /storageadapter /virtual-drive# set raid-level value |
指定した仮想ドライブの RAID レベルを指定します。 |
ステップ 6 | Server chassis /storageadapter /virtual-drive# set physical-drive value |
指定した仮想ドライブに物理ドライブを指定します。 |
次に、仮想ドライブを編集する例を示します。
Server# scope chassis Server /chassis # scope storageadapter slot-3 Server /chassis/storageadapter # scope virtual-drive 3 Server /chassis/storageadapter/virtual-drive #set raid-level 1 Server /chassis/storageadapter/virtual-drive *# physical-drive 1 Server /chassis/storageadapter/virtual-drive* #commit Server /chassis/storageadapter /virtual-drive # modify-attribute Current write policy: Write Back Good BBU 0: Write Through 1: Write Back Good BBU 2: Always Write Back Choose number from above options--> 0 The following attribute will be modified: - Write Policy: Write Through OK? (y or n)--> y Server /chassis/storageadapter/virtual-drive #
このタスクでは、仮想ドライブがドライブ グループの仮想ドライブのターゲット ID である場合に、既存のドライブ グループ内のすべての VD を保護します。
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |||
---|---|---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 | ||
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 | ||
ステップ 3 | Server /chassis/storageadapter # scope virtual-drive drive-number |
指定された仮想ドライブのコマンド モードを開始します。 | ||
ステップ 4 | Server /chassis/storageadapter/virtual-drive # secure-drive-group |
処理の確認を求めるプロンプトが表示されます。確認のために yes を入力します。
|
次に、仮想ドライブ グループを保護する例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # scope virtual-drive 3 Server /chassis/storageadapter/virtual-drive # secure-drive-group This will enable security for virtual drive 16, and all virtual drives sharing this drive group. It is not reversible. Are you quite certain you want to do this? Enter 'yes' to confirm -> yes server /chassis/storageadapter/virtual-drive # show detail Virtual Drive 16: . . FDE Capable: 1 FDE Enabled: 1 . . server /chassis/storageadapter/virtual-drive #
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # scope virtual-drive 3 |
仮想ドライブのコマンド モードを開始します。 |
ステップ 4 | Server /chassis/storageadapter/virtual-drive # modify-attributes |
現在のものとは異なるポリシーを選択するように求めるプロンプトが表示されます。 |
次に、既存の RAID 1 ドライブ グループ内の未使用のスペースから新しい仮想ドライブを分割する例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # scope virtual-drive Server /chassis/storageadapter/virtual-drive # modify-attributes Current write policy: Write Back 0: Write Through 1: Write Back 2: Write Back even if Bad BBU Choose number from above options --> 0 The following attribute will be modified: - Write policy: Write Through OK? (y or n) --> y operation in progress. Server /chassis/storageadapter/virtual-drive #
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # scope physical-drive drive-number |
指定された物理ドライブのコマンド モードを開始します。 |
ステップ 4 | Server /chassis/storageadapter/physical-drive # make-dedicated-hot-spare |
専用ホット スペアが作成される仮想ドライブの選択を求めるプロンプトが表示されます。 |
次に、物理ドライブ 3 を仮想ドライブ 6 の専用ホット スペアにする例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # scope physical-drive 3 Server /chassis/storageadapter/physical-drive # make-dedicated-hot-spare 5: VD_OS_1, RAID 0, 102400 MB, physical disks: 1 6: VD_OS_2, RAID 0, 12288 MB, physical disks: 1 7: VD_OS_3, RAID 0, 12288 MB, physical disks: 1 8: VD_DATA_1, RAID 0, 12512 MB, physical disks: 1 9: RAID1_2358, RAID 1, 40000 MB, physical disks: 2,3,5,8 11: JFB_RAID1_67, RAID 1, 20000 MB, physical disks: 6,7 12: JFB_Crv_R1_40, RAID 1, 40000 MB, physical disks: 6,7 13: JFB_R1_10GB, RAID 1, 10000 MB, physical disks: 6,7 Please choose from the above 8 virtual drives-->6 Server /chassis/storageadapter/physical-drive #
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # scope physical-drive drive-number |
指定された物理ドライブのコマンド モードを開始します。 |
ステップ 4 | Server /chassis/storageadapter/physical-drive # make-global-hot-spare | |
ステップ 5 | Server /chassis/storageadapter/physical-drive # get-operation-status | ドライブ上で処理中のタスクのステータスを表示します。 |
次に、物理ドライブ 3 をグローバル ホット スペアにする例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # scope physical-drive 3 Server /chassis/storageadapter/physical-drive # make-global-hot-spare Server /chassis/storageadapter/physical-drive #
Unconfigured Good ステータスが表示された物理ドライブ上でのみ、このタスクを確認できます。
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # scope physical-drive drive-number |
指定された物理ドライブのコマンド モードを開始します。 |
ステップ 4 | Server /chassis/storageadapter/physical-drive # prepare-for-removal |
次に、物理ドライブ 3 を削除する準備をする例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # scope physical-drive 3 Server /chassis/storageadapter/physical-drive # prepare-for-removal Server /chassis/storageadapter/physical-drive #
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # scope physical-drive 4 |
物理ドライブのコマンド モードを開始します。 |
ステップ 4 | Server /chassis/storageadapter/physical-drive # make-unconfigured-good |
ドライブのステータスを Unconfigured good に変更します。 |
ステップ 5 | Server /chassis/storageadapter/physical-drive # make-jbod |
物理ドライブの JBOD モードを有効にします。 |
次に、物理ドライブのステータスを切り替える例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # scope physical-drive 4 Server /chassis/storageadapter/physical-drive # show detail Physical Drive Number 4: Controller: SLOT-4 Health: Good Status: JBOD Boot Drive: true Manufacturer: ATA Model: ST500NM0011 Predictive Failure Count: 0 Drive Firmware: CC02 Coerced Size: 476416 MB Type: HDD Server /chassis/storageadapter/physical-drive # make-unconfigured-good Server /chassis/storageadapter/physical-drive # show detail Physical Drive Number 4: Controller: SLOT-4 Health: Good Status: Unconfigured Good Boot Drive: true Manufacturer: ATA Model: ST500NM0011 Predictive Failure Count: 0 Drive Firmware: CC02 Coerced Size: 476416 MB Type: HDD Server /chassis/storageadapter/physical-drive # make-jbod Server /chassis/storageadapter/physical-drive # show detail Physical Drive Number 4: Controller: SLOT-4 Health: Good Status: JBOD Boot Drive: true Manufacturer: ATA Model: ST500NM0011 Predictive Failure Count: 0 Drive Firmware: CC02 Coerced Size: 476416 MB Type: HDD
コマンドまたはアクション | 目的 | |||
---|---|---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 | ||
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 | ||
ステップ 3 | Server /chassis/storageadapter # scope physical-drive 4 |
物理ドライブのコマンド モードを開始します。 | ||
ステップ 4 | Server /chassis/storageadapter/physical-drive # set-boot-drive |
処理の確認を求めるプロンプトが表示されます。確認のために yes を入力します。
|
次に、物理ドライブをコントローラのブート ドライブとして設定する例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # show detail PCI Slot SLOT-4: Health: Good Controller Status: Optimal ROC Temperature: Not Supported Product Name: MegaRAID 9240-8i (RAID 0,1,10,5) Serial Number: SP23807413 Firmware Package Build: 20.11.1-0159 Product ID: LSI Logic Battery Status: no battery Cache Memory Size: 0 MB Boot Drive: none Boot Drive is PD: false TTY Log Status: Not Downloaded Server /chassis/storageadapter # scope physical-drive 4 Server /chassis/storageadapter/physical-drive # set-boot-drive Are you sure you want to set physical drive 4 as the boot drive? Enter 'yes' to confirm -> yes Server /chassis/storageadapter/physical-drive # exit Server /chassis/storageadapter # show detail PCI Slot SLOT-4: Health: Good Controller Status: Optimal ROC Temperature: Not Supported Product Name: MegaRAID 9240-8i (RAID 0,1,10,5) Serial Number: SP23807413 Firmware Package Build: 20.11.1-0159 Product ID: LSI Logic Battery Status: no battery Cache Memory Size: 0 MB Boot Drive: 4 Boot Drive is PD: true TTY Log Status: Not Downloaded
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # scope physical-drive drive-number |
指定された物理ドライブのコマンド モードを開始します。 |
ステップ 4 | Server /chassis/storageadapter/physical-drive # remove-hot-spare | ホット スペア プールからドライブを削除します。 |
次に、ホット スペア プールから物理ドライブ 3 を削除する例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # scope physical-drive 3 Server /chassis/storageadapter/physical-drive # remove-hot-spare Server /chassis/storageadapter/physical-drive #
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # scope physical-drive drive-number |
指定された物理ドライブのコマンド モードを開始します。 |
ステップ 4 | Server /chassis/storageadapter/physical-drive # undo-prepare-for-removal |
次に、物理ドライブ 3 の削除を準備した後にドライブをリスピンする例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # scope physical-drive 3 Server /chassis/storageadapter/physical-drive # undo-prepare-for-removal Server /chassis/storageadapter/physical-drive #
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 |
---|
次に、バッテリの自動学習サイクルをイネーブルにする例を示します。
Server # scope chassis Server /chassis # scope storageadapter SLOT-2 Server /chassis/storageadapter # scope bbu Server /chassis/storageadapter/bbu # enable-auto-learn Automatic BBU learn cycles will occur without notice if enabled. Are you sure? [y/n] --> y enable-auto-learn initiated Server /chassis/storageadapter/bbu #
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 |
---|
次に、バッテリの自動学習サイクルをディセーブルにする例を示します。
Server # scope chassis Server /chassis # scope storageadapter SLOT-2 Server /chassis/storageadapter # scope bbu Server /chassis/storageadapter/bbu # disable-auto-learn Automatic BBU learn cycles will no longer occur if disabled. Are you sure? [y/n] --> y disable-auto-learn initiated Server /chassis/storageadapter/bbu #
このコマンドを使用するには、admin としてログインする必要があります。
コマンドまたはアクション | 目的 |
---|
次に、バッテリの学習サイクルを開始する例を示します。
Server # scope chassis Server /chassis # scope storageadapter SLOT-2 Server /chassis/storageadapter # scope bbu Server /chassis/storageadapter/bbu # start-learn-cycle Server /chassis/storageadapter/bbu #
このタスクを実行するには、admin としてログインする必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # scope physical-drive 3 |
物理ドライブ コマンド モードを開始します。 |
ステップ 4 | Server /chassis/storageadapter/physical-drive # locator-led {on | off} |
物理ドライブのロケータ LED を有効または無効にします。 |
次に、物理ドライブ 3 のロケータ LED を有効にする例を示します。
Server # scope chassis Server /chassis # scope storageadapter SLOT-2 Server /chassis/storageadapter # scope physical-drive 3 Server /chassis/storageadapter/physical-drive # locator-led on Server /chassis/storageadapter/physical-drive* # commit Server /chassis/storageadapter/physical-drive #
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 |
---|
次に、コントローラ設定をクリアする例を示します。
Server # scope chassis Server /chassis # scope storageadapter SLOT-HBA 1 Server /chassis/storageadapter # clear-all-config Are you sure you want to clear the controller's config and delete all VDs? Enter 'yes' to confirm -> yes Enter administrative password to proceed with operation\n Password -> Password accepted. Performing requested operation. Server /chassis/storageadapter #
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 |
---|
次に、コントローラの設定パラメータを出荷時のデフォルトに復元する例を示します。
Server # scope chassis Server /chassis # scope storageadapter SLOT-HBA 1 Server /chassis/storageadapter # set-factory-defaults This operation will restore controller settings to factory default values. Do you want to proceed? Enter 'yes' to confirm -> yes Server /chassis/storageadapter #
このタスクを実行するには、admin 権限でログインする必要があります。
コマンドまたはアクション | 目的 |
---|
次に、ストレージ コントローラのログを表示する例を示します。
Server # scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # show log Time Severity Description ---- -------- ------------- Fri March 1 09:52:19 2013 Warning Predictive Failure Fri March 1 07:50:19 2013 Info Battery charge complete Fri March 1 07:50:19 2013 Info Battery charge started Fri March 1 07:48:19 2013 Info Battery relearn complete Fri March 1 07:47:19 2013 Info Battery is discharging Fri March 1 07:45:19 2013 Info Battery relearn started Server /chassis/storageadapter #
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scope storageadapter slot |
装着されているストレージ カードに対してコマンド モードを開始します。 |
ステップ 3 | Server /chassis/storageadapter # scope physical-drive 2 |
物理ドライブ コマンド モードを開始します。 |
ステップ 4 | Server /chassis/storageadapter/physicsl-drive # show detail |
物理ドライブの詳細を表示します。 |
次に、物理ドライブの情報を表示する例を示します。
Server# scope chassis Server /chassis # scope storageadapter SLOT-3 Server /chassis/storageadapter # scope physical-drive 202 Server /chassis/storageadapter/physical-drive # show detail Physical Drive Number 202: Controller: SLOT-HBA Info Valid: Yes Info Invalid Cause: Enclosure Device ID: 252 Device ID: 8 Drive Number: 202 Health: Good Status: Online Boot Drive: false Manufacturer: ATA Model: INTEL SSDSC2BB480G4 Predictive Failure Count: 0 Drive Firmware: 0370 Type: SSD Block Size: 512 Physical Block Size: 4096 Negotiated Link Speed: 6.0 Gb/s Locator LED: false FDE Capable: 0 FDE Enabled: 0 FDE Secured: 0 FDE Locked: 0 FDE Locked Foreign Config: 0 Enclosure Association: Direct Attached Enclosure Logical ID: N/A Enclosure SAS Address[0]: N/A Enclosure SAS Address[1]: N/A Power Cycle Count: 106 Power On Hours: 10471 Percentage Life Left: 100 Wear Status in Days: 1825 Percentage Reserved Capacity Consumed: 0 Time of Last Refresh : 2017-03-04 13:47 Operating Temperature: 34 Media Error Count: 0 Other Error Count: 0 Interface Type: SATA Block Count: 937703088 Raw Size: 457862 MB Non Coerced Size: 457350 MB Coerced Size: 456809 MB SAS Address 0: 4433221108000000 SAS Address 1: 0x0 Power State: active
Flexible Flash コントローラの管理
C シリーズ ラックマウント サーバ によっては、サーバ ソフトウェア ツールおよびユーティリティのストレージとして、内蔵 Secure Digital(SD)メモリ カードをサポートしています。この SD カードは Cisco Flexible Flash ストレージ アダプタでホストされます。
Cisco IMC では、単一ハイパーバイザ(HV)パーティション設定として SD ストレージが使用可能です。以前のバージョンでは 4 つの仮想 USB ドライブがありました。3 つには Cisco UCS Server Configuration Utility、Cisco ドライバ、および Cisco Host Upgrade Utility が事前ロードされ、4 番目はユーザ インストールによるハイパーバイザでした。また、Cisco IMC の最新バージョンにアップグレードするか、旧バージョンにダウングレードした後、設定をリセットした場合にも、単一 HV パーティション設定が作成されます。
シスコ ソフトウェア ユーティリティおよびパッケージの詳細については、次の URL の『Cisco UCS C-Series Servers Documentation Roadmap』を参照してください。
http://www.cisco.com/go/unifiedcomputing/c-series-doc
Cisco Flexible Flash コントローラでは、単一のカードに加えて 2 つの SD カードを RAID-1 ペアとして管理できます。カード管理機能の導入により、次の作業を実行できます。
(注) |
|
アクション |
説明 |
---|---|
Cisco Flex Flash のリセット(Reset Cisco Flex Flash) |
コントローラをリセットできます。 |
パーティション デフォルトのリセット(Reset Partition Defaults) |
選択したスロットの設定をデフォルト設定にリセットできます。 |
カード設定の同期(Synchronize Card Configuration) |
ファームウェア バージョン 253 以降をサポートする SD カードの設定を保持できます。 |
運用プロファイルの設定(Configure Operational Profile) |
選択した Cisco Flexible Flash コントローラの SD カードを設定できます。 |
非 RAID パーティションは常にプライマリ カードから列挙されます。列挙はプライマリ カードのステータスに依存しません。
次に、Cisco Flexible Flash コントローラに 2 枚のカードがあるときの RAID パーティションの列挙の動作を示します。
シナリオ | 動作 |
---|---|
シングル カード |
RAID パーティションは、カードが正常に動作している場合、およびモードが [プライマリ(Primary)] または [セカンダリ アクティブ(Secondary-active)] の場合に列挙されます。 |
デュアル ペア カード |
RAID パーティションは、カードの 1 つが正常に動作していれば列挙されます。 1 枚のカードだけが正常に動作している場合、すべての読み取り/書き込み操作は、この正常に動作しているカードで行われます。2 つの RAID パーティションを同期するには UCS SCU を使用する必要があります。 |
デュアル非ペア カード |
サーバを再起動するときにこのシナリオが検出された場合、RAID パーティションはいずれも列挙されません。 サーバが稼働しているときにこのシナリオが検出された場合、ユーザが新しい SD カードを取り付けても、そのカードは Cisco Flexible Flash コントローラによって管理されません。これはホストの列挙には影響しません。これらを管理するためにカードをペアにする必要があります。カードをペアにするには、[パーティション デフォルトのリセット(Reset Partition Defaults)] または [カード設定の同期(Synchronize Card Configuration)] オプションを使用します。 |
次のいずれかの方法で、FlexFlash を使用したシングル カード ミラーリングからデュアル カード ミラーリングにアップグレードできます。
サーバに空の FlexFlash カードを追加し、最新バージョンにファームウェアをアップグレードします。
FlexFlash ファームウェアを最新バージョンにアップグレードした後、空のカードをサーバに追加します。
このいずれかの方法を使用する前に、次のガイドラインを考慮してください。
RAID1 ミラーリングを作成するには、サーバに追加される空のカードのサイズが、サーバ上の既存のカードと正確に同じである必要があります。RAID1 ミラーリングをセットアップするうえで、同じカード サイズは必須事項です。
ハイパーバイザ パーティション内の有効なデータを持つカードが、プライマリ正常カードとしてマークされていることを確認してください。Cisco IMC GUI または Cisco IMC CLI でこの状態を判別できます。カードの状態をプライマリ正常としてマークするには、Cisco IMC GUI の [設定情報のリセット(Reset Configuration)] オプションを使用するか、Cisco IMC CLI で reset-config コマンドを実行します。特定のカードの設定をリセットすると、セカンダリ カードはセカンダリ アクティブ非正常としてマークされます。
RAID 正常性「Degraded」状態である場合、すべての読み取りおよび書き込みトランザクションは正常なカードで実行されます。このシナリオでは、データのミラーリングは行われません。データのミラーリングは、正常な RAID 状態の場合にのみ行われます。
データのミラーリングは RAID パーティションにのみ適用されます。C シリーズ サーバでは、RAID モードでハイパーバイザ パーティションだけが動作します。
旧バージョンで使用するよう SD カードを設定していない場合、最新バージョンにアップグレードすると最新の 253 ファームウェアがロードされ、4 個のパーティションすべてがホストに列挙されます。
FlexFlash バージョンのアップグレード中に次のエラー メッセージが表示される場合があります。
Unable to communicate with Flexible Flash controller: operation ffCardsGet, status CY_AS_ERROR_INVALID_RESPONSE”
さらに、カード ステータスが [不明(missing)] と示されることもあります。このエラーが発生する原因は、1.4(x) などの代替リリースまたは旧バージョンに意図せず切替えたためです。この場合、最新バージョンに戻すか、元の FlexFlash 1.4(x) 設定に切り替えることができます。最新の Cisco IMC バージョンに戻すことを選択した場合、Cisco FlexFlash 設定はそのまま残ります。旧バージョンの設定に切り替えることを選択した場合は、Flexflash 設定をリセットする必要があります。その場合、次の点に注意する必要があります。
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scopeflexflash |
指定コントローラに対して Cisco Flexible Flash コントローラ コマンド モードを開始します。 |
ステップ 3 | Server /chassis/flexflash # scopeoperational-profile |
運用プロファイル コマンド モードを開始します。 |
ステップ 4 | Server /chassis/flexflash/operational-profile # setread-error-count- slot1-threshold threshold |
スロット 1 の Cisco Flexible Flash カードへのアクセス中に許可される読み取りエラーの数を指定します。エラー数がこのしきい値を超えると、Cisco Flexible Flash カードがディセーブルになります。Cisco IMC が再アクセスを試みる前に、カードをリセットする必要があります。 読み取りエラーのしきい値を指定するには、1 ~ 255 の整数を入力します。検出されたエラー数に関係なく、カードがディセーブルにならないように指定するには、0(ゼロ)を入力します。 |
ステップ 5 | Server /chassis/flexflash/operational-profile # setread-error-count- slot2-threshold threshold |
スロット 2 の Cisco Flexible Flash カードへのアクセス中に許可される読み取りエラーの数を指定します。エラー数がこのしきい値を超えると、Cisco Flexible Flash カードがディセーブルになります。Cisco IMC が再アクセスを試みる前に、カードをリセットする必要があります。 読み取りエラーのしきい値を指定するには、1 ~ 255 の整数を入力します。検出されたエラー数に関係なく、カードがディセーブルにならないように指定するには、0(ゼロ)を入力します。 |
ステップ 6 | Server /chassis/flexflash/operational-profile # setwrite-error-count-slot2-threshold threshold |
スロット 2 の Cisco Flexible Flash カードへのアクセス中に許可される書き込みエラーの数を指定します。エラー数がこのしきい値を超えると、Cisco Flexible Flash カードがディセーブルになります。Cisco IMC が再アクセスを試みる前に、カードをリセットする必要があります。 書き込みエラーのしきい値を指定するには、1 ~ 255 の整数を入力します。検出されたエラー数に関係なく、カードがディセーブルにならないように指定するには、0(ゼロ)を入力します。 |
ステップ 7 | Server /chassis/flexflash/operational-profile # commit |
トランザクションをシステム設定にコミットします。 |
次に、Flash コントローラのプロパティを設定する例を示します。
Server# scope chassis Server /chassis # scope flexflash FlexFlash-0 Server /chassis/flexflash # scope operational-profile Server /chassis/flexflash/operational-profile # set read-err-count-slot1-threshold 9 Server /chassis/flexflash/operational-profile *# set read-err-count-slot2-threshold 10 Server /chassis/flexflash/operational-profile *# set write-err-count-slot1-threshold 11 Server /chassis/flexflash/operational-profile *# set write-err-count-slot2-threshold 12 Server /chassis/flexflash/operational-profile *# commit Server /chassis/flexflash/operational-profile # show detail FlexFlash Operational Profile: Firmware Operating Mode: util SLOT1 Read Error Threshold: 9 SLOT1 Write Error Threshold: 11 SLOT2 Read Error Threshold: 10 SLOT2 Write Error Threshold: 12
通常の操作では、Cisco Flexible Flash のリセットが必要になることはありません。テクニカル サポートの担当者から明確に指示された場合にだけ、この手順を実行することを推奨します。
(注) | この操作は、Cisco Flexible Flash コントローラ上の仮想ドライブへのトラフィックを中断させます。 |
コマンドまたはアクション | 目的 |
---|
この例では、フラッシュ コントローラをリセットします。
Server# scope chassis Server /chassis # scope flexflash FlexFlash-0 Server /chassis/flexflash # reset This operation will reset Cisco Flexible Flash controller. Host traffic to VDs on this device will be disrupted. Continue?[y|N] y Server /chassis/flexflash #
ミラー モードでコントローラ カードを設定します。
コマンドまたはアクション | 目的 | |||
---|---|---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 | ||
ステップ 2 | Server /chassis # scopeflexflash |
指定コントローラに対して Cisco Flexible Flash コントローラ コマンド モードを開始します。 | ||
ステップ 3 | Server /chassis/flexflash # configure-cards-mirror SLOT-1. |
正常なプライマリとして SLOT-1 を設定します。 | ||
ステップ 4 | 「Enable auto sync(by default auto sync is disabled)?[y|N]」プロンプトで y と入力します。 |
スロット 1 のカードとスロット 2 のカードを同期します。 | ||
ステップ 5 | 「 Set Mirror Partition Name(Default name is Hypervisor)?[y|N]」プロンプトで y と入力します。 |
ミラー パーティションの名前を設定できるようにします。 | ||
ステップ 6 | 「Enter Partition Name Mirror Partition Name :Hypervisor」プロンプトでミラー パーティションの名前を入力します。 |
ミラー パーティションの名前を設定します。 | ||
ステップ 7 | 「 Set Virtual Drive as non-removable (Default is removable)?[y|N]」プロンプトで y と入力します。 |
非リムーバブルとして VD を設定することができます。 次のメッセージが表示されます。このアクションは、SLOT-1 を正常なプライマリ スロットしてマークし、SLOT-2 を非正常なセカンダリとしてマークします。 この操作は、ホスト接続を妨げる場合もあります。 | ||
ステップ 8 | 「Continue?[y|N]y」プロンプトで y と入力します。 |
ミラー モードでカードを設定し、SLOT-1 のカードをプライマリで正常なカード、SLOT-2(カードが存在する場合)を非正常なセカンダリのカードとして設定します。 | ||
ステップ 9 | Server /chassis/flexflash # show physical-drive | (任意)
|
次に、ミラー モードでコントローラ カードを設定する例を示します。
Server# scope chassis Server /chassis # scope flexflash Server /chassis/flexflash # configure-cards-mirror SLOT-1 Enable auto sync(by default auto sync is disabled)?[y|N]y Set Mirror Partition Name(Default name is Hypervisor)?[y|N]y Enter Partition Name Mirror Partition Name :HV Set Virtual Drive as non-removable (Default is removable)?[y|N]y This action will mark the SLOT-1 as healthy primary slot and SLOT-2 (if card existing) as unhealthy secondary. This operation may disturb the host connectivity as well. Continue?[y|N]y Server /chassis/flexflash # show detail Controller FlexFlash-0: Product Name: Cisco FlexFlash Controller HW: FX3S Vendor: Cypress Firmware Version: 1.3.2 build 159 Firmware Operating Mode: mirror Firmware Configured Mode: mirror Has Error: No Error Description: Internal State: Disconnected Controller Status: OK Cards Manageable: Yes Startup Firmware Version: 1.3.2 build 159 Server /chassis/flexflash # show physical-drive Physical Drive Status Controller Card Type Card mode Health Sync Mode --------------- --------- ------------ ----------------- ----------------- ---------- ---------- SLOT-1 present FlexFlash-0 FX3S configured mirror-primary healthy auto SLOT-2 present FlexFlash-0 FX3S configured mirror-secondary unhealthy auto Server /chassis/flexflash #
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scopeflexflash |
指定コントローラに対して Cisco Flexible Flash コントローラ コマンド モードを開始します。 |
ステップ 3 | Server /chassis/ flexflash # scopevirtual-drive |
指定したコントローラに対して仮想デバイス コマンド モードを開始します。 |
ステップ 4 | Server /chassis/flexflash/virtual-drive # enable-vds "SCU HUU dlfd" |
ホストに対して仮想ドライブをイネーブルにします。 |
次に、仮想デバイスをホストに対してイネーブルにする例を示します。
Server# scope chassis Server /chassis # scope flexflash Server /chassis/flexflash # scope virtual-drive Server /chassis/flexflash/virtual-drive # enable-vds "SCU HUU dlfd" Server /chassis/flexflash/virtual-drive # show detail Virtual Drive SCU: VD ID: 1 Size: 2560 MB VD Scope: Non-Raid VD Status: Healthy VD Type: Removable Read/Write: R/W Host Accessible: Connected Operation in progress: NA Last Operation completion status: none Virtual Drive HUU: VD ID: 2 Size: 1536 MB VD Scope: Non-Raid VD Status: Healthy VD Type: Removable Read/Write: R/W Host Accessible: Connected Operation in progress: NA Last Operation completion status: none Virtual Drive Drivers: VD ID: 3 Size: 8192 MB VD Scope: Non-Raid VD Status: Healthy VD Type: Removable Read/Write: R/W Host Accessible: Not-Connected Operation in progress: NA Last Operation completion status: none Virtual Drive dlfd: VD ID: 4 Size: 9952 MB VD Scope: Non-Raid VD Status: Healthy VD Type: Removable Read/Write: R/W Host Accessible: Connected Operation in progress: NA Last Operation completion status: none Virtual Drive dfdff: VD ID: 5 Size: 30432 MB VD Scope: Non-Raid VD Status: Healthy VD Type: Removable Read/Write: R/W Host Accessible: Not-Connected Operation in progress: NA Last Operation completion status: none Server /chassis/flexflash/virtual-drive #
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scopeflexflash |
指定コントローラに対して Cisco Flexible Flash コントローラ コマンド モードを開始します。 |
ステップ 3 | Server /chassis/ flexflash # scopevirtual-drive |
指定したコントローラに対して仮想デバイス コマンド モードを開始します。 |
ステップ 4 | Server /chassis/flexflash/virtual-drive # erase-vds "SCU HUU" |
FAT32 の消去を開始します。 |
次に、仮想デバイスでデータを消去する例を示します。
Server# scope chassis Server /chassis # scope flexflash Server /chassis/flexflash # scope virtual-drive Server /chassis/flexflash/virtual-drive # erase-vds "SCU HUU" Server /chassis/flexflash/virtual-drive # show detail Virtual Drive SCU: VD ID: 1 Size: 2560 MB VD Scope: Non-Raid VD Status: Healthy VD Type: Removable Read/Write: R/W Host Accessible: Not-Connected Operation in progress: Erasing Last Operation completion status: none Virtual Drive HUU: VD ID: 2 Size: 1536 MB VD Scope: Non-Raid VD Status: Healthy VD Type: Removable Read/Write: R/W Host Accessible: Connected Operation in progress: Erase-Pending Last Operation completion status: none Virtual Drive Drivers: VD ID: 3 Size: 8192 MB VD Scope: Non-Raid VD Status: Healthy VD Type: Removable Read/Write: R/W Host Accessible: Not-Connected Operation in progress: NA Last Operation completion status: none Virtual Drive dlfd: Server /chassis/flexflash/virtual-drive #
コマンドまたはアクション | 目的 | |||
---|---|---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 | ||
ステップ 2 | Server /chassis # scopeflexflash |
指定コントローラに対して Cisco Flexible Flash コントローラ コマンド モードを開始します。 | ||
ステップ 3 | Server /chassis/ flexflash # scopevirtual-drive |
指定したコントローラに対して仮想デバイス コマンド モードを開始します。 | ||
ステップ 4 | Server /chassis/flexflash/virtual-drive # sync-vds Hypervisor |
|
次に、仮想ドライブを同期する例を示します。
Server# scope chassis Server /chassis # scope flexflash Server /chassis/flexflash # scope virtual-drive Server /chassis/flexflash/virtual-drive # sync-vds Hypervisor Server /chassis/flexflash/virtual-drive # show detail Virtual Drive Hypervisor: VD ID: 1 Size: 30432 MB VD Scope: Raid VD Status: Degraded VD Type: Removable Read/Write: R/W Host Accessible: Not-Connected Operation in progress: Syncing(Manual)10% done Last Operation completion status: none Server /chassis/flexflash/virtual-drive #
お使いのプラットフォームで Cisco Flexible Flash がサポートされている必要があります。
コマンドまたはアクション | 目的 |
---|
Flexible Flash コント ローラのログの例です。
Server # scope chassis Server /chassis # scope chassis flexflash FlexFlash-0 Server /chassis/flexflash # show logs TimeStamp Severity Description --------- –------- ----------- 2017 July 10 07:16:17 UTC warning "CYWB_LOG: CYWB: USB connection status, 3.0 enable=1, 3.0 mode=1" 2017 July 10 07:46:05 UTC warning "CYWB_LOG: CYWB: USB connection status, 3.0 enable=1, 3.0 mode=1" 2017 July 10 07:46:05 UTC warning "CYWB_LOG: CYWB FWLOG (usbapp): USB HSChirp event, data=1" 2017 July 10 07:45:07 UTC warning "CYWB_LOG: CYWB FWLOG (usbapp): USB Suspend event, data=0" 2017 July 10 07:45:06 UTC warning "CYWB_LOG: CYWB FWLOG (usbapp): USB VbusValid event, data=0" 2017 July 10 07:44:23 UTC warning "CYWB_LOG: CYWB FWLOG (usb): connect done, usb_state=4 ctrl_reg=0" 2017 July 10 07:44:23 UTC info "cywb_blkdev_create_disks: Finished changing disks: S0=0 S1=0 RAID=0 TOTAL=0" 2017 July 10 07:44:23 UTC info "cywbblkdev_blk_put: disk=cd3ad400 queue=cd3bd360 port=0 unit=0 usage=0" 2017 July 10 07:44:23 UTC info "cywb_blkdev_create_disks: S2 unit 0 has become unavailable" 2017 July 10 07:44:23 UTC info "CYWB_LOG: Found 0 RAID partitions, 0 partitions on port0 and 0 partitions on port 1" 2017 July 10 07:44:23 UTC info cywb_blkdev_create_disks called 2017 July 10 07:44:23 UTC info "cywb_blkdev_create_disks: Scheduling driver callback" 2017 July 10 07:44:23 UTC info "cywbblkdev: Added disk=cd3ad400 queue=cd3bd360 port=0 unit=0" 2017 July 10 07:44:23 UTC info "cywbblkdev: Registered block device cydiskraida with capacity 124727295 (major=254, minor=0)" 2017 July 10 07:44:23 UTC info cywbblkdev_blk_release exit 2017 July 10 07:44:23 UTC info "cywbblkdev_blk_put: disk=cd3ad400 queue=cd3bd360 port=0 unit=0 usage=1" 2017 July 10 07:44:23 UTC info cywbblkdev_blk_release entry 2017 July 10 07:44:23 UTC warning "CYWB_LOG: CyWb: Disk on port0, unit0 is busy, waiting" 2017 July 10 07:44:23 UTC warning "CYWB_LOG: CYWB: No device found on storage port 0" 2017 July 10 07:44:23 UTC info cywbblkdev_revalidate_disk called 2017 July 10 07:44:23 UTC info cywbblkdev_blk_open exit 2017 July 10 07:44:23 UTC info cywbblkdev_media_changed called 2017 July 10 07:44:23 UTC info cywbblkdev_blk_open entry 2017 July 10 07:44:23 UTC info "cywb_blkdev_create_disks: Finished changing disks: S0=0 S1=0 RAID=1 TOTAL=1"
C シリーズ M5 ラックマウント サーバは、サーバ ソフトウェア ツールおよびユーティリティのストレージ用に microSD メモリ カードをサポートします。ライザー 1 にはこの microSD メモリ カード スロットがあります。Cisco FlexUtil は、32 GB の microSD カードのみをサポートします。
次のユーザ認識可能なパーティションが microSD カードに存在します。
Server Configuration Utility(SCU)–1.25 GB
診断-0.25 GB
Host Update Utility(HUU)–1.5 GB
ドライバ–8 GB
ユーザ(User)
(注) | MicroSD の各パーティションの数とサイズは固定されています。 |
(注) | ユーザ パーティションはストレージにのみ使用する必要があります。 |
コマンドまたはアクション | 目的 | |||
---|---|---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 | ||
ステップ 2 | Server /chassis # scopeflexutil |
FlexUtil コントローラ コマンド モードを開始します。 | ||
ステップ 3 | Server /chassis/flexutil # scopeoperational-profile |
運用プロファイル コマンド モードを開始します。 | ||
ステップ 4 | Server /chassis/flexutil/operational-profile # setread-err-count-threshold count |
| ||
ステップ 5 | Server /chassis/flexutil/operational-profile* # setwrite-err-count-threshold count |
| ||
ステップ 6 | Server /chassis/flexutil/operational-profile* # commit |
トランザクションをシステムにコミットします。 |
次に、FlexUtil 運用プロファイルを設定する例を示します。
Server# scope chassis Server /chassis # scope flexutil Server /chassis/flexutil # scope operational-profile Server /chassis/flexutil/operational-profile # set read-err-count-threshold 49 Server /chassis/flexutil/operational-profile* # set write-err-count-threshold 49 Server /chassis/flexutil/operational-profile* # commit Server /chassis/flexutilServer /chassis/flexutil/operational-profile
コマンドまたはアクション | 目的 |
---|
次の例は、FlexUtil カード構成をリセットする方法を示しています。
Server# scope chassis Server /chassis # scope flexutil Server /chassis/flexutil # reset-card-config This operation will wipe all the data on the card. Any VD connected to host (except UserPartition) will be disconnected from host. This task will take few minutes to complete. Do you want to continue?[y|N]y Server /chassis/flexutil #
お使いのプラットフォームで Cisco FlexUtil がサポートされている必要があります。
コマンドまたはアクション | 目的 |
---|
次の例では、FlexUtil コントローラのプロパティを表示します。
Server# scope chassis Server /chassis # scope flexutil Server /chassis/flexutil # show detail Controller Flexutil: Product Name: Cisco Flexutil Internal State: Connected Controller Status: OK Physical Drive Count: 1 Virtual Drive Count: 5 Server /chassis/flexutil #
お使いのプラットフォームで Cisco FlexUtil がサポートされている必要があります。
コマンドまたはアクション | 目的 |
---|
次の例では、FlexUtil 物理ドライブのプロパティを表示します。
Server# scope chassis Server /chassis # scope flexutil Server /chassis/flexutil # show physical-drive detail Physical Drive microSD: Status: present Controller: Flexutil Health: healthy Capacity: 30624 MB Write Enabled: true Read Error Count: 0 Read Error Threshold: 49 Write Error Count: 0 Write Error Threshold : 49 Product Name: SD32G Product Revision: 3.0 Serial#: 0x1cafb Manufacturer Id: 39 OEM Id: PH Manufacturing Date : 12/2016 Block Size: 512 bytes Partition Count: 5 Drives Enabled: SCU Diagnostics HUU Drivers UserPartition Server /chassis/flexutil #
お使いのプラットフォームで Cisco FlexUtil がサポートされている必要があります。
コマンドまたはアクション | 目的 |
---|
次の例では、FlexUtil 物理ドライブのプロパティを表示します。
Server# scope chassis Server /chassis # scope flexutil Server /chassis/flexutil # scope virtual-drive Server /chassis/flexutil/virtual-drive # show detail Virtual Drive SCU: ID: 1 LUN ID: NA Size: 1280 MB VD Scope: Non-RAID VD Status: Healthy VD Type: Removable Read/Write: R/W Host Accessible: Not-Connected Operation in progress: NA Last Operation completion status: none Virtual Drive Diagnostics: ID: 2 LUN ID: 0 Size: 256 MB VD Scope: Non-RAID VD Status: Healthy VD Type: Removable Read/Write: R/W Host Accessible: Connected Operation in progress: NA Last Operation completion status: none Virtual Drive HUU: ID: 3 LUN ID: NA Size: 1536 MB VD Scope: Non-RAID VD Status: Healthy VD Type: Removable Read/Write: R/W Host Accessible: Not-Connected Operation in progress: NA Last Operation completion status: none Virtual Drive Drivers: ID: 4 LUN ID: NA Size: 8192 MB VD Scope: Non-RAID VD Status: Healthy VD Type: Removable Read/Write: R/W Host Accessible: Not-Connected Operation in progress: NA Last Operation completion status: none Virtual Drive UserPartition: ID: 5 LUN ID: NA Size: 11159 MB VD Scope: Non-RAID VD Status: Healthy VD Type: Removable Read/Write: R/W Host Accessible: Not-Connected Operation in progress: NA Last Operation completion status: none Server /chassis/flexutil/virtual-drive #
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | server # scopechassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scopeflexutil |
FlexUtil コントローラ コマンド モードを開始します。 |
ステップ 3 | Server /chassis/flexutil # scopevd-image-configs |
仮想ドライブ イメージ コンフィギュレーション コマンド モードを開始します。 |
ステップ 4 | Server /chassis/flexutil/vd-image-configs # vd-image-cifs {virtual-drive-nameremote-shareremote-file-path [mount options] |
FlexUtil 仮想ドライブに CIFS ファイルをマップします。次を指定する必要があります。 |
ステップ 5 | Server /chassis/flexutil/vd-image-configs # vd-image-nfs {virtual-drive-nameremote-shareremote-file-path [mount options] |
FlexUtil 仮想ドライブに NFS ファイルをマップします。次を指定する必要があります。 |
ステップ 6 | Server /chassis/flexutil/vd-image-configs # show detail |
FlexUtil 仮想ドライブ イメージの詳細が表示されます。 |
次の例に、イメージを FlexUtil 仮想ドライブにマップする方法を示します。
Server# scope chassis Server /chassis # scope flexutil Server /chassis/flexutil # scope vd-image-configs Server /chassis/flexutil/vd-image-configs # vd-image-nfs HUU 10.10.10.10:/nfsdata ucs-c240m5-huu-3.1.0.182.iso Server /chassis/flexutil/vd-image-configs # show detail Virtual drive: SCU mount-type: nfs remote-share: 10.10.10.10:/nfsshare remote-file: ucs-cxx-scu-4.0.12.3.iso mount-options: 'nolock,noexec,noac,soft,timeo=60,retry=2,rsize=3072,wsize=3072' Virtual drive: Diagnostics mount-type: nfs remote-share: 10.10.10.10:/nfsshare remote-file: ucs-cxx-diag.5.0.1a.iso mount-options: 'nolock,noexec,noac,soft,timeo=60,retry=2,rsize=3072,wsize=3072' Virtual drive: HUU mount-type: nfs remote-share: 10.10.10.10:/nfsdata remote-file: ucs-c240m5-huu-3.1.0.182.iso mount-options: "nolock,noexec,noac,soft,timeo=60,retry=2,rsize=3072,wsize=3072" Virtual-drive: Drivers mount-type: None remote-share: None remote-file: None mount-options: None Server /chassis/flexutil/vd-image-configs #
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scopeflexutil |
FlexUtil コントローラ コマンド モードを開始します。 |
ステップ 3 | Server /chassis/flexutil # scopevirtual-drive |
仮想ドライブ コマンド モードを開始します。 |
ステップ 4 | Server /chassis/flexutil/virtual-drive # update-vds virtual-drive |
選択した仮想ドライブを更新します。 |
ステップ 5 | Server /chassis/flexutil/virtual-drive # update-vds-cancel | (任意)
進行中の仮想ドライブの更新をキャンセルします。 |
ステップ 6 | Server /chassis/flexutil/virtual-drive # show detail |
FlexUtil 仮想ドライブ イメージの詳細が表示されます。 |
次に、FlexUtil 仮想ドライブを更新する例を示します。
Server# scope chassis Server /chassis # scope flexutil Server /chassis/flexutil # scope virtual-drive Server /chassis/flexutil/virtual-drive # update-vds HUU Server /chassis/flexutil/virtual-drive # show detail Virtual-drive: SCU partition-id: 1 lun-id: NA size: 1280 MB partition-scope: Non-RAID partition-status: Healthy partition-type: Removable writable: R/W host-accessible: Not-Connected operation-in-progress: NA operation-completion-status: none Virtual-drive: Diagnostics partition-id: 2 lun-id: NA size: 256 MB partition-scope: Non-RAID partition-status: Healthy partition-type: Removable writable: R/W host-accessible: Not-Connected operation-in-progress: NA operation-completion-status: none Virtual-drive: HUU partition-id: 3 lun-id: NA size: 1536 MB partition-scope: Non-RAID partition-status: Healthy partition-type: Removable writable: R/W host-accessible: Not-Connected operation-in-progress: Updating operation-completion-status: none Virtual-drive: Drivers partition-id: 4 lun-id: NA size: 8192 MB partition-scope: Non-RAID partition-status: Healthy partition-type: Removable writable: R/W host-accessible: Not-Connected operation-in-progress: NA operation-completion-status: none Virtual drive: UserPartition partition-id: 5 lun-id: NA size: 11159 MB partition-scope: Non-RAID partition-status: Healthy partition-type: Removable writable: R/W host-accessible: Not-Connected operation-in-progress: NA operation-completion-status: none Server /chassis/flexutil/virtual-drive #
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scopeflexutil |
FlexUtil コントローラ コマンド モードを開始します。 |
ステップ 3 | Server /chassis/flexutil # scopevirtual-drive |
仮想ドライブ コマンド モードを開始します。 |
ステップ 4 | Server /chassis/flexutil/virtual-drive # enable-vds virtual-drive |
仮想ドライブをホストにマップします。 |
ステップ 5 | Server /chassis/flexutil/virtual-drive # show detail |
FlexUtil 仮想ドライブ イメージの詳細が表示されます。 |
次の例は、仮想ドライブ イメージのホストへのマップ方法を示します。
Server# scope chassis Server /chassis # scope flexutil Server /chassis/flexutil # scope virtual-drive Server /chassis/flexutil/virtual-drive # enable-vds HUU Server /chassis/flexutil/virtual-drive # show detail Virtual Drive ID LUN ID Size VD Status Host Accessible Operation in Last Operation progress completion status -------------- ------ ------ -------- ------------ ----------------- ------------ ----------------- SCU 1 NA 1280 MB Healthy Not-Connected NA none Diagnostics 2 0 256 MB Healthy Connected NA Update-Success HUU 3 1 1536 MB Healthy Connected NA Update-Success Drivers 4 NA 8192 MB Healthy Not-Connected NA none UserPartition 5 NA 11159 MB Healthy Not-Connected NA none Server /chassis/flexutil/vd-image-configs #
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scopeflexutil |
FlexUtil コントローラ コマンド モードを開始します。 |
ステップ 3 | Server /chassis/flexutil # scopevd-image-configs |
仮想ドライブ イメージ コンフィギュレーション コマンド モードを開始します。 |
ステップ 4 | /chassis/flexutil/vd-image-configs # vd-image-nfs HUU nfs/cifs share IP and path ISO image file |
IP と nfs/cifs 共有のパス、および ISO イメージ ファイルを指定します。 |
ステップ 5 | /chassis/flexutil/vd-image-configs # show detail |
FlexUtil 仮想ドライブ イメージの詳細が表示されます。 |
次の例に、イメージを FlexUtil 仮想ドライブに追加する方法を示します。
Server# scope chassis Server /chassis # scope flexutil Server /chassis/flexutil # scope vd-image-configs Server /chassis/flexutil/vd-image-configs # vd-image-nfs HUU 10.127.54.176:/nfsdata ucs-c240m5-huu-3.1.0.182.iso Server /chassis/flexutil/vd-image-configs # show detail virtual-drive: SCU mount-type: nfs remote-share: 10.104.236.81:/nfsshare remote-file: ucs-cxx-scu-4.0.12.3.iso mount-options: 'nolock,noexec,noac,soft,timeo=60,retry=2,rsize=3072,wsize=3072' virtual-drive: Diagnostics mount-type: nfs remote-share: 10.104.236.81:/nfsshare remote-file: ucs-cxx-diag.5.0.1a.iso mount-options: 'nolock,noexec,noac,soft,timeo=60,retry=2,rsize=3072,wsize=3072' virtual-drive: HUU mount-type: nfs remote-share: 10.127.54.176:/nfsdata remote-file: ucs-c240m5-huu-3.1.0.182.iso mount-options: "nolock,noexec,noac,soft,timeo=60,retry=2,rsize=3072,wsize=3072" virtual-drive: Drivers mount-type: None remote-share: None remote-file: None mount-options: None Server /chassis/flexutil/vd-image-configs
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scopeflexutil |
FlexUtil コントローラ コマンド モードを開始します。 |
ステップ 3 | Server /chassis/flexutil # scopevd-image-configs |
仮想ドライブ イメージ コンフィギュレーション コマンド モードを開始します。 |
ステップ 4 | Server /chassis/flexutil/vd-image-configs # unmap virtual-drive |
選択した仮想ドライブのイメージをマッピング解除します。 |
ステップ 5 | Server /chassis/flexutil/vd-image-configs # show detail |
FlexUtil 仮想ドライブ イメージの詳細が表示されます。 |
次に、FlexUtil 仮想ドライブのマッピングを解除する例を示します。
Server# scope chassis Server /chassis # scope flexutil Server /chassis/flexutil # scope vd-image-configs Server /chassis/flexutil/vd-image-configs # unmap HUU Server /chassis/flexutil/vd-image-configs # show detail Virtual drive: SCU mount-type: nfs remote-share: 10.10.10.10:/nfsshare remote-file: ucs-cxx-scu-4.0.12.3.iso mount-options: 'nolock,noexec,noac,soft,timeo=60,retry=2,rsize=3072,wsize=3072' Virtual drive: Diagnostics mount-type: nfs remote-share: 10.10.10.10:/nfsshare remote-file: ucs-cxx-diag.5.0.1a.iso mount-options: 'nolock,noexec,noac,soft,timeo=60,retry=2,rsize=3072,wsize=3072' Virtual drive: HUU mount-type: None remote-share: None remote-file: None mount-options: None Virtual-drive: Drivers mount-type: None remote-share: None remote-file: None mount-options: None Server /chassis/flexutil/vd-image-configs #
コマンドまたはアクション | 目的 | |
---|---|---|
ステップ 1 | Server# scope chassis |
シャーシ コマンド モードを開始します。 |
ステップ 2 | Server /chassis # scopeflexutil |
FlexUtil コントローラ コマンド モードを開始します。 |
ステップ 3 | Server /chassis/flexutil # scopevirtual-drive |
仮想ドライブ コマンド モードを開始します。 |
ステップ 4 | Server /chassis/flexutil/virtual-drive # erase-vds virtual-drive |
仮想ドライブのイメージを消去します。 |
ステップ 5 | Server /chassis/flexutil/virtual-drive # show detail |
FlexUtil 仮想ドライブ イメージの詳細が表示されます。 |
次の例は、仮想ドライブの削除方法を示します。
Server# scope chassis Server /chassis # scope flexutil Server /chassis/flexutil # scope virtual-drive Server /chassis/flexutil/virtual-drive # erase-vds SCU This operation will erase data on the VD Continue?[y|N]y Server /chassis/flexutil/virtual-drive # show detail Virtual Drive ID LUN ID Size VD Status Host Accessible Operation in Last Operation progress completion status -------------- ------ ------ -------- ------------ ----------------- ------------ ----------------- SCU 1 NA 1280 MB Healthy Not-Connected Erasing none Diagnostics 2 0 256 MB Healthy Connected NA Update-Success HUU 3 1 1536 MB Healthy Connected NA Update-Success Drivers 4 NA 8192 MB Healthy Not-Connected NA none UserPartition 5 NA 11159 MB Healthy Not-Connected NA none C220-WZP210606A7 /chassis/flexutil/virtual-drive #