Native Profiling

Information About Native Profiling

You can profile devices based on HTTP and DHCP to identify the end devices on the network. You can configure device-based policies and enforce these policies per user or per device policy on the network.

Policies allow profiling of mobile devices and basic onboarding of the profiled devices to a specific VLAN. They also assign ACL and QoS or configure session timeouts.

You can configure policies as two separate components:

  • Defining policy attributes as service templates that are specific to clients joining the network and applying policy match criteria

  • Applying match criteria to the policy.


Note

Before proceeding with the native profile configuration, ensure that HTTP Profiling and DHCP Profiling are enabled.

To configure Native Profiling, use one of the following procedures:

  • Create a service template

  • Create a class map


    Note

    You can apply a service template using either a class map or parameter map.

  • Create a parameter-map and associate the service template to parameter-map

    • Create a policy map

      1. If class-map has to be used: Associate the class-map to the policy-map and associate the service-template to the class-map.

      2. If parameter-map has to be used: Associate the parameter-map to the policy-map

    • Associate the policy-map to the policy profile.

Creating a Class Map (GUI)

Procedure

Step 1

Click Configuration > Services > QoS.

Step 2

In the QoS – Policy area, click Add to create a new QoS Policy or click the one you want to edit.

Step 3

Add Add Class Map and enter the details.

Step 4

Click Save.

Step 5

Click Update and Apply to Device.

Creating a Class Map (CLI)


Note

Configuration of class maps via CLI offer more options and can be more granular than GUI.

Procedure

  Command or Action Purpose

Step 1

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 2

class-map type control subscriber match-any class-map-name

Example:

Device(config)# class-map type control subscriber match-any cls_user

Specifies the class map type and name.

Step 3

match username username

Example:

Device(config-filter-control-classmap)# match username ciscoise

Specifies the class map attribute filter criteria.

Step 4

class-map type control subscriber match-any class-map-name

Example:

Device(config)# class-map type control subscriber match-any cls_userrole

Specifies the class map type and name.

Step 5

match user-role user-role

Example:

Device(config-filter-control-classmap)# match user-role engineer

Specifies the class map attribute filter criteria.

Step 6

class-map type control subscriber match-any class-map-name

Example:

Device(config)# class-map type control subscriber match-any cls_oui

Specifies the class map type and name.

Step 7

match oui oui-address

Example:

Device(config-filter-control-classmap)# match oui 48.f8.b3

Specifies the class map attribute filter criteria.

Step 8

class-map type control subscriber match-any class-map-name

Example:

Device(config)# class-map type control subscriber match-any cls_mac

Specifies the class map type and name.

Step 9

match mac-address mac-address

Example:

Device(config-filter-control-classmap)# match mac-address 0040.96b9.4a0d

Specifies the class map attribute filter criteria.

Step 10

class-map type control subscriber match-any class-map-name

Example:

Device(config)# class-map type control subscriber match-any cls_devtype

Specifies the class map type and name.

Step 11

match device-type device-type

Example:

Device(config-filter-control-classmap)# match device-type windows

Specifies the class map attribute filter criteria.

Step 12

match join-time-of-day start-time end-time

Example:

Device(config-filter-control-classmap)# match join-time-of-day 10:30 12:30

Specifies a match to the time of day.

Here, join time is considered for matching. For example, if the match filter is set from 11:00 am to 2:00 pm, a device joining at 10:59 am is not considered, even if it acquires credentials after 11:00 am.

Here,

start-time and end-time specifies the 24-hour format.

Use the show class-map type control subscriber name name command to verify the configuration.

Note

 

You should also disable AAA override for this command to work.

Creating a Service Template (GUI)

Procedure

Step 1

Choose Configuration > Security > Local Policy.

Step 2

On the Local Policy page, Service Template tab, click ADD.

Step 3

In the Create Service Template window, enter the following parameters:

  • Service Template Name: Enter a name for the template.

  • VLAN ID: Enter the VLAN ID for the template. Valid range is between 1 and 4094.

  • Session Timeout (secs): Sets the timeout duration for the template. Valid range is between 1 and 65535.

  • Access Control List: Choose the Access Control List from the drop-down list.

  • Ingress QOS: Choose the input QoS policy for the client from the drop-down list

  • Egress QOS: Choose the output QoS policy for the client from the drop-down list.

Step 4

Click Save & Apply to Device.

Creating a Service Template (CLI)

Procedure

  Command or Action Purpose

Step 1

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 2

service-template service-template-name

Example:

Device(config)# service-template svc1

Enters service template configuration mode.

Step 3

vnid vnid

Example:

Device(config-service-template)# vnid test

Specifies the VXLAN network identifier (VNID).

Use the show service-template service-template-name command to verify the configuration.

Step 4

access-group access-list-name

Example:

Device(config-service-template)# access-group acl-auto

Specifies the access list to be applied.

Step 5

vlan vlan-id

Example:

Device(config-service-template)# vlan 10

Specifies VLAN ID. Valid range is from 1-4094.

Step 6

absolute-timer timer

Example:

Device(config-service-template)# absolute-timer 1000

Specifies session timeout value for a service template. Valid range is from 1-65535.

Step 7

service-policy qos input qos-policy

Example:

Device(config-service-template)# service-policy qos input in_qos

Configures an input QoS policy for the client.

Step 8

service-policy qos output qos-policy

Example:

Device(config-service-template)# service-policy qos output out_qos

Configures an output QoS policy for the client.

Creating a Parameter Map

Procedure

  Command or Action Purpose

Step 1

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 2

parameter-map type subscriber attribute-to-service parameter-map-name

Example:

Device(config)# parameter-map type subscriber attribute-to-service param

Specifies the parameter map type and name.

Step 3

map-indexmap device-type eqfilter-name

Example:

Device(config-parameter-map-filter)# 1 map device-type eq "windows" 
mac-address eq 3c77.e602.2f91 username eq "cisco"

Specifies the parameter map attribute filter criteria. Multiple filters are used in the example provided here.

Step 4

map-indexservice-templateservice-template-name precedence precedence-num

Example:

Device(config-parameter-map-filter-submode)# 1 service-template svc1 precedence 150

Specifies the service template and its precedence.

Creating a Policy Map (GUI)

Procedure

Step 1

Choose Configuration > Security > Local Policy > Policy Map tab..

Step 2

Enter a name for the Policy Map in the Policy Map Name text field.

Step 3

Click Add

Step 4

Choose the service template from the Service Template drop-down list.

Step 5

For the following parameters select the type of filter from the drop-down list and enter the required match criteria

  • Device Type

  • User Role

  • User Name

  • OUI

  • MAC Address

Step 6

Click Add Criteria

Step 7

Click Update & Apply to Device.

Creating a Policy Map (CLI)

Before you begin

Before removing a policy map or parameter map, you should remove it from the target or shut down the WLAN profile or delete the session.

Procedure

  Command or Action Purpose

Step 1

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 2

policy-map type control subscriber policy-map-name

Example:

Device(config)# policy-map type control subscriber polmap5

Specifies the policy map type.

Step 3

event identity-update match-all

Example:

Device(config-event-control-policymap)# event identity-update match-all

Specifies the match criteria to the policy map.

Step 4

You can apply a service template using either a class map or a parameter map, as shown here.

  • class-num class class-map-name do-until-failure
  • action-index activate service-template service-template-name
  • action-index map attribute-to-service table parameter-map-name

Example:

The following example shows how a class-map with a service-template has to be applied:

Device(config-class-control-policymap)# 10 class cls_mac do-until-failure
Device(config-action-control-policymap)# 10 activate service-template svc1

Example:

The following example shows how a parameter map has to be applied (service template is already associated with the parameter map ‘param’ while creating it): 

Device(config-action-control-policymap)#1 map attribute-to-service table param

Configures the local profiling policy class map number and specifies how to perform the action or activates the service template or maps an identity-update attribute to an auto-configured template.

Step 5

end

Example:

Device(config-action-control-policymap)# end

Exits configuration mode.

Step 6

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 7

wireless profile policy wlan-policy-profile-name

Example:

Device(config)# wireless profile policy wlan-policy-profilename

Configures a wireless policy profile.

Caution

 

Do not configure aaa-override for native profiling under a named wireless profile policy. Native profiling is applied at a lower priority than AAA policy. If aaa-override is enabled, the AAA policies will override native profile policy.

Step 8

description profile-policy-description

Example:

Device(config-wireless-policy)# description "default policy profile"

Adds a description for the policy profile.

Step 9

dhcp-tlv-caching

Example:

Device(config-wireless-policy)# dhcp-tlv-caching

Configures DHCP TLV caching on a WLAN.

Step 10

http-tlv-caching

Example:

Device(config-wireless-policy)# http-tlv-caching

Configures client HTTP TLV caching on a WLAN.

Step 11

subscriber-policy-name policy-name

Example:

Device(config-wireless-policy)# subscriber-policy-name polmap5

Configures the subscriber policy name.

Step 12

vlan vlan-id

Example:

Device(config-wireless-policy)# vlan 1

Configures a VLAN name or VLAN ID.

Step 13

no shutdown

Example:

Device(config-wireless-policy)# no shutdown

Saves the configuration.

Configuring Native Profiling in Local Mode

To configure native profiling in the local mode, you must follow the steps described in . In the policy profile, you must enable central switching as described in the step given below in order to configure native profiling.

Procedure

Command or Action Purpose

central switching

Example:

Device(config-wireless-policy)# central switching

Enables central switching.

Verifying Native Profile Configuration

Use the following show commands to verify the native profile configuartion: 

Device# show wireless client device summary 

Active classified device summary
MAC Address       Device-type                       User-role                             Protocol-map  
------------------------------------------------------------------------------------------------------
1491.82b8.f94b    Microsoft-Workstation             sales                                            9  
1491.82bc.2fd5    Windows7-Workstation              sales                                           41 
 
Device# show wireless client device cache

Cached classified device info
 
MAC Address       Device-type                       User-role                             Protocol-map  
------------------------------------------------------------------------------------------------------
2477.031b.aa18    Microsoft-Workstation                                                              9  
30a8.db3b.a753    Un-Classified Device                                                               9  
4400.1011.e8b5    Un-Classified Device                                                               9  
980c.a569.7dd0    Un-Classified Device        
Device# show wireless client mac-address 4c34.8845.e32c detail | s 
Session Manager:
  Interface :
  IIF ID           : 0x90000002
  Device Type      : Microsoft-Workstation
  Protocol Map     : 0x000009
  Authorized       : TRUE
  Session timeout  : 1800
  Common Session ID: 78380209000000174BF2B5B9
  Acct Session ID  : 0
  Auth Method Status List
  	Method : MAB
  		SM State        : TERMINATE
  		Authen Status   : Success
  Local Polices:
  	Service Template : wlan_svc_C414.3CCA.0A51 (priority 254)
  		Absolute-Timer   : 1800
  Server Polices:
  Resultant Policies:
  Filter-ID        : acl-auto
  Input QOS        : in_qos
  Output QOS       : out_qos
  Idle timeout     : 60 sec
  VLAN              : 10
  Absolute-Timer   : 1000

Use the following show command to verify the class map details for a class map name: 

Device# show class-map type control subscriber name test
Class-map               Action                       Exec  Hit  Miss  Comp
---------                ------                      ----  ---  ----   ---
match-any test     match day Monday                    0     0    0     0    
match-any test     match join-time-of-day 8:00 18:00   0     0    0     0    
Key:
  "Exec" - The number of times this line was executed
  "Hit"  - The number of times this line evaluated to TRUE
  "Miss" - The number of times this line evaluated to FALSE
  "Comp" - The number of times this line completed the execution of its
       condition without a need to continue on to the end