Services Commands

connectorctl service restart

This command restarts all the Cisco Spaces: Connector services. To enable debug logs, use the -l keyword is specified. 

connectorctl service restart -s service-name [ -l debug-level [ -d debug-period-in-minutes ] ]

Syntax Description

Keyword and Variable Description

-s service-name

Configure the service that needs to be restarted.

-l debug-level

(Optional) Configure the debug level. Values are DEBUG, INFO, and WARNING.
  • If debug-level is unspecified, the default value is DEBUG.

Note

 

Running the service at DEBUG log level would significantly impact performance

-d debug-period-in-minutes

(Optional) Specify the debug period in minutes. If unspecified, the default value is 10 minutes.

  • If -l is unspecified, service is restarted but debugging is not logged.

Command History

Release 3

This command is introduced.

Examples

You can also restart a specified service. The following is a sample output of the command: 
$[spacesadmin@connector ~]$ connectorctl service restart -s location -l DEBUG
Executing command:service
Command execution status: Success

Status:Successfully started location

connectorctl service status

To display the status of all the services running on the Cisco Spaces: Connector, use the connectorctl service status command.

connectorctl service status [ -s service-name ]

Syntax Description

Keywords and Variables

Description

-s service-name

Displays the status of a specified service only.

Command History

Release 3

This command is introduced.

Examples

You can view the status of all configured services.  The following is a sample output of the command: 
[spacesadmin@ connector ~]$ connectorctl service status
Executing command:service
Command execution status:Success

location(3.0.1.266) status:Up(1 m 34s)
You can view the status of a specified service. The following is a sample output of the command: 
[spacesadmin @ connector ~ ]S connectorctl service status -s location
Executing command:service
Command execution status: Success

location (3.0.1.266) status:Up(5m 50s)

connectorctl service stop

To stop the specified service running on the Cisco Spaces: Connector, use the connectorctl service stop command. .

connectorctl service stop [ -s service-name ]

Syntax Description

Keywords and Variables

Description

-s service-name

Stops the specified service.

Command History

Release 3

This command is introduced.

Examples

The following is a sample output of the command: 
[spacesadmin@connector ~]$ connectorctl service stop -s location
Executing command:service
Command execution status:Success
-----------------------
Status:Successfully stopped location

connectorctl service network

To configure the Cisco Spaces: Connector services network, use the connectorctl service network command.

connectorctl service network { -r | -i ip-address | -c cidr | -s }

Syntax Description

Keywords and Variables

Description

-r

Resets services network to default.

-i ip-address

Base IPv4 address or IPv6 address.

-c cidr

Classless Inter-Domain Routing (CIDR) range.

-g

IPv4 or IPv6 gateway address.

-s

Shows current service network configuration.

Command History

Release 3

This command is introduced.

Examples

You can configure the IPv4 address of the network and the CIDR range.The following is a sample output of the command: 
[spacesadmin@ connector ~ ]$ connectorctl service network -i 172.18.0.0 -c 16 -g 172.18.0.1
Executing command:service
Command execution status:Success

Successfully updated service network to given config
You can view the current service network configurations. The following is a sample output of the command: 
[spacesadmin @ connector ~ ]S connectorctl service network -s

Executing command: service
Command execution status: Success

Base Ip Address: 172.18.0.0
cidr range: 16,
Gateway: 172.18.0.1

Examples

You can also configure the IPv6 address of the network and the CIDR range. The following is a sample output of the command: 
[spacesadmin@ connector ~ ]$ connectorctl service network -i 172.18.0.0 -c 16 -g 172.18.0.1 -i 2001:db8:1::
-c 64 -g 2001:db8:1::1

Executing command:service
Command execution status:Success

Successfully updated service network to given config
You can view the current service network configurations. The following is a sample output of the command: 
[spacesadmin @ connector ~ ]S connectorctl service network -s

Executing command:service
Command execution status:Success
-----------------------
Base Ip Address: 172.18.0.0
2001:db8:1::
cidr range: 16,
64,
Gateway: 172.18.0.1
2001:db8:1::1