Release Notes for Cisco ASR 901 Series Aggregation Services Router for Cisco IOS Release 15.5(3)S10

Release Notes for Cisco ASR 901 Series Aggregation Services Router for Cisco IOS Release 15.5(3)S10

---

First Published Date: September 24, 2019

This release notes is for the Cisco ASR 901 Series Aggregation Services Router for Cisco IOS Release 15.5(3)S10 and contains the following sections:

• Introduction
• System Specifications and Memory Details
• New and Changed Information
• Supported Hardware
• Caveats
• Troubleshooting
• Related Documentation
• Obtaining Documentation and Submitting a Service Request

Introduction

The Cisco ASR 901 Series Aggregation Services Router is a cell-site access platform specifically designed to aggregate and transport mixed-generation radio access network (RAN) traffic. The router is used at the cell site edge as a part of a 2G, 3G, or 4G RAN.

The Cisco ASR 901 router helps enable a variety of RAN solutions by extending IP connectivity to devices using Global System for Mobile Communications (GSM), General Packet Radio Service (GPRS), Node Bs using High Speed Packet Access (HSPA) or Long Term Evolution (LTE), base transceiver stations (BTSs) using Enhanced Data Rates for GSM Evolution (EDGE), Code Division Multiple Access (CDMA), CDMA-2000, EVDO, or WiMAX, and other cell-site equipment.

It transparently and efficiently transports cell-site voice, data, and signaling traffic over IP using traditional T1 and E1 circuits, as well as alternative backhaul networks such as Carrier Ethernet and DSL, Ethernet in the First Mile (EFM), and WiMAX. It also supports standards-based Internet Engineering Task Force (IETF) Internet protocols over the RAN transport network, including those standardized at the Third-Generation Partnership Project (3GPP) for IP RAN transport. Custom designed for the cell site, the Cisco ASR 901 router features a small form factor, extended operating temperature, and cell-site DC input voltages.

Table 1 lists the Cisco ASR 901 1G Router model versions.

Table 2 lists the Cisco ASR 901 10G Router model versions.

Note Some of the Cisco ASR 901 models have port based licensing. For more details, see the Licensing chapter in Cisco ASR 901 Series Aggregation Services Router Software Configuration Guide.

System Specifications and Memory Details

Table 3 lists the supported system configurations and memory details for the Cisco ASR 901 router:

New and Changed Information

• New Hardware Features in Release 15.5(3)S10
• New Software Features in Release 15.5(3)S10
• Modified Software Features in Release 15.5(3)S10

Important Notes

• 10G SFPs inserted into 1GE port provides 1GE speed.
• 10G SFPs inserted into 10GE port without a valid license provides only 1GE speed.
• 100M SFP works only with no negotiation auto command.
• If 1G SFP is used to connect a 10G port to a 1G port, you do not have to explicitly configure the no negotiation auto command to bring up the link.
• Effective with Cisco IOS Release 15.4(3)S, the auto-select feature is supported on 100M SFPs. However, this feature is not supported on combo ports.
• Remote Fault Indication feature is not applicable for 1G mode in 10GE ports. It applies only to 10G mode in 10GE ports.

Table 4 SFPs Supported on the Cisco ASR 901 1G and 10G Routers for 1G Mode

CWDM-SFP-1470 CWDM-SFP-1490 CWDM-SFP-1510 CWDM-SFP-1530 CWDM-SFP-1550 CWDM-SFP-1570 CWDM-SFP-1590 CWDM-SFP-1610 CWDM SFP+ DWDM-SFP-XXXX1 GLC-BX-U and GLC-BX-D2 GLC-EX-SMD GLC-LH-SMD GLC-LX-SM-RGD GLC-SX-MMD

GLC-SX-MM-RGD GLC-T GLC-ZX-SM GLC-ZX-SMD GLC-ZX-SM-RGD SFP-GE-L SFP-GE-S SFP-GE-T SFP-GE-Z GLC-BX40-D-I GLC-BX40-DA-I GLC-BX40-U-I GLC-BX80-D-I GLC-BX80-U-I

1.40 wavelengths 2.These SFPs (GLC-BX-U and GLC-BX-D) should be connected back to back to bring the interface link up.

Table 5 SFPs Supported on the Cisco ASR 901 10G Router for 10G Mode

SFP-10G-ER SFP-10G-LR SFP-10G-LR-X DWDM-SFP+ SFP-H10GB-CU1M SFP-H10GB-CU3M SFP-H10GB-CU5M

SFP-10G-SR SFP-10G-SR-X SFP-10G-ZR SFP-10G-LRM SFP-H10GB-ACU7M SFP-H10GB-ACU10M

---

Note For information on how to configure SFPs, see the Cisco ASR 901 Series Aggregation Services Router Software Configuration Guide.

---

Caveats

Caveats describe unexpected behavior in Cisco IOS software releases. Severity 1 caveats are the most serious caveats, severity 2 caveats are less serious, and severity 3 caveats are the least serious of these three severity levels. Only select severity 3 caveats are listed.

This section contains the following topics:

• Bug Search Tool
• Open Caveats
• Resolved Caveats

Troubleshooting

The following sections describe troubleshooting commands you can use with the router.

Collecting Data for Router Issues

To collect data for reporting router issues, issue the following command:

• show tech-support —Displays general information about the router if it reports a problem.

Collecting Data for ROMMON Issues

To collect data for ROMMON issues, issue the following command while in the EXEC mode:

• show rom-monitor —Displays currently selected ROM monitor.

Note If you contact Cisco support for assistance, we recommend that you provide any crashinfo files stored in flash memory. For more information about crashinfo files, see http://www.cisco.com/en/US/products/hw/routers/ps167/products_tech_note09186a00800a6743.shtml.

Related Documentation

Documents related to the Cisco ASR 901 Series Aggregation Services Router include the following:

• Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide
• Cisco ASR 901 Series Aggregation Services Router Software Configuration Guide
• Regulatory Compliance and Safety Information for Cisco ASR 901 Series Aggregation Services Routers
• Cisco ASR 901 Series Aggregation Services Router Series MIB Specifications Guide

To access the related documentation on Cisco.com, go to:

• Cisco ASR 901 1G Router home page: http://www.cisco.com/en/US/partner/products/ps12077/tsd_products_support_series_home.html
• Cisco ASR 901 10G Router home page: http://www.cisco.com/c/en/us/support/routers/asr-901-10g-series-aggregation-services-routers/tsd-products-support-series-home.html

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, using the Cisco Bug Search Tool (BST), submitting a service request, and gathering additional information, see What’s New in Cisco Product Documentation.

To receive new and revised Cisco technical content directly to your desktop, you can subscribe to the  What’s New in Cisco Product Documentation RSS feed. The RSS feeds are a free service.