Activate the Cisco IMC firmware, using the following cmdlet:

Get-ImcFirmwareBootDefinition -Type "blade-controller" | 
Get-ImcFirmwareBootUnit | Set-ImcFirmwareBootUnit-AdminState trigger -Image backup -ResetOnActivate yes -Force

Get-ImcLocalUser -Id 9 | Set-ImcLocalUser -Name “admin” -pwd “Password” -AccountStatus “active” -Priv “admin”

Note	Clear-ImcLocalUser changes the status to inactive and does not remove the user or data.

Desired State Configuration (DSC) is a new approach for configuring local and remote machines. You can use IMC DSC resources to configure multiple IMC in a datacenter from a centralized root server. PowerTool module Cisco.UCS.DesiredStateConfiguration contains all the custom IMC DSC resources.

Get-Module Cisco.UCS.DesiredStateConfiguration -ListAvailable
Get-DscResource | where{$_.Module -ilike 'Cisco*' 
-and $_.Name -ilike 'imc*'} | Select Name

A DSC resource can execute in parallel, and maximum number of XML API connections on any Cisco IMC is limited to 4. So, specify add DependsOn property to each IMC DSC resource in such cases.

Create a user credential, using the following cmdlet:

$user = "<username>"
$password = "<password>"
$cred = New-Object System.Management.Automation.PSCredential($user,$password)

Update Cisco IMC Firmware, using the following cmdlet:

Get-ImcFirmwareUpdatable -Type blade-controller | Set-ImcFirmwareUpdatable -AdminState trigger -Type blade-controller -Protocol ftp -RemoteServer "10.65.183.111" -RemotePath "/UcseBin/UCSE_CIMC_2.3.1.bin"-RemoteCredential $cred-Force

To clear the boot drive, use the following cmdlet:

Get-ImcStorageController | Set-ImcStorageController -AdminAction "clear-boot-drive" -Force

Configure LDAP server using the below cmdlet:

Set-ImcAaaLdap -Basedn 'DC=cisco,DC=com' -Domain 'cisco.com' -AdminState enabled -BindMethod configured-credentials -Encryption disabled -LdapServer1 1.1.1.1 -LdapServerPort1 389 -Timeout 60 -Password ***** -ErrorAction Stop -Force -Xml

Configure the NTP settings, using the following cmdlet:

Get-ImcNtpServer | Set-ImcNtpServer -NtpEnable “yes” -NtpServer1 1.1.1.1 -Force

When Confirm - Switch parameter in a PowerTool cmdlet is specified, you are prompted to confirm the changes. Cmdlet sends a request to confirm the changes applied to the system which is outside of the Windows PowerShell environment. For example, if a cmdlet is executed to clear an SNMP user, the cmdlet requires confirmation from the user to complete the action.

Get-ImcSnmpUser -Name snmpuser | Clear-ImcSnmpUser -Confirm
Confirm
Are you sure you want to perform this action?
Performing the operation "Clear-ImcSnmpUser" on target "Clear".
[Y] Yes [A] Yes to All [N] No [L] No to All [S] Suspend [?] Help (default is "Y"):

Configure the SoL, using the following cmdlet:

Get-ImcSolif -Dn “sys/rack-unit-1/sol-if” | Set-ImcSolIf -AdminState “enable” -Speed “57600” -Force

Create a virtual drive using unused physical drive.

Get-ImcStorageVirtualDriveCreatorUsingUnusedPhysicalDrive | 
Set-ImcStorageVirtualDriveCreatorUsingUnusedPhysicalDrive 
-AdminState trigger -size "400 MB" -DriveGroup "[2]" -RaidLevel 0 -VirtualDriveName "vd_111" -Force

Create a virtual drive using a virtual drive group

Get-ImcStorageVirtualDriveCreatorUsingVirtualDriveGroup | 
Set-ImcStorageVirtualDriveCreatorUsingVirtualDriveGroup 
-AdminState trigger -VirtualDriveName "vd_New"-SharedVirtualDriveId "3" -Size "100 MB" -Force

Create a virtual drive from multiple drives

Get-ImcStorageController | 
Set-ImcStorageVirtualDriveCreatorUsingUnusedPhysicalDrive 
-AdminState trigger -DriveGroup "[1,2]" -RaidLevel 1 -Size "285148 MB" -VirtualDriveName "RAID1_12" -WritePolicy "Always Write Back" -Force

Disables the controller lock key depending on its current state on the disk.

Note	On disabling the drive security, the data on all secure drives becomes unusable.

Get-ImcStorageController | Disable-ImcDriveSecurity -Force
Get-ImcSelfEncryptStorageController | Disable-ImcDriveSecurity –Force

Enables the controller lock key depending on its current state on the disk.

Get-ImcStorageController | Enable-ImcDriveSecurity -KeyId “myKey123” -SecurityKey “myPass123” -Force

Enables the uploaded PID catalogue on the IMC server.

Get-ImcPidCatalog | Enable-ImcPidCatalog –Force

Enable IP blocking, using the following cmdlet:

Get-ImcIpBlocking | Set-ImcIpBlocking -Enable “yes”

The Export-ImcHardwareInventory cmdlet exports the hardware inventory of the system to a remote location. You can also specify the remote server details, such as IP/HostName, protocol, path and filename, username and password, if any.

Export-ImcHardwareInventory -Chassis <EquipmentChassis> -Hostname <string> [-Proto <string>] [-Pwd <string>] 
-RemoteFile <string> [-User <string>] [-XtraProperty <Hashtable>] [-Force] [<CommonParameters>]

Export-ImcHardwareInventory -TopSystem <TopSystem> -Hostname <string> [-Proto <string>] 
[-Pwd <string>] -RemoteFile <string> [-User <string>] [-XtraProperty <Hashtable>] [-Force] [<CommonParameters>]

Get-ImcTopSystem | Export-ImcHardwareInventory -Hostname "10.10.10.10" -Proto scp -User root 
-Pwd <password> -RemoteFile "/root/test/InventoryExportReport.txt" -Force

# Get SysdebugMEpLog managed object, where Type equals to "SEL" or "Syslog".

Get-ImcRackUnit | Get-ImcMgmtController | Get-ImcSysdebugMEpLog -Filter '(type -ilike SEL) -or (Type -clike Syslog)'

# Get SysdebugMEpLog managed object, where Type equals to "SEL" or #"Syslog", and Id equals to "0".

Get-ImcRackUnit | Get-ImcMgmtController | Get-ImcSysdebugMEpLog -Filter '(type -ilike SEL) -or (Type -clike Syslog)' -Id 0 -Type SEL

# Get a local user, where a name can be "admin" (case sensitive).

Get-ImcManagedObject -ClassId aaaUser -Filter 'Name -clike admin'

# Get User, where a name can be"test*" (support * regular expression or case sensitive).

Get-ImcManagedObject -ClassId aaaUser -Filter 'Name -clike test*'

# Get a local user, where AccountStatus is not equals to inactive.

Get-ImcManagedObject -ClassId aaaUser -Filter 'AccountStatus -cne inactive'

# Get a local user, where AccountStatus matches 'inacti'.

Get-ImcManagedObject -ClassId aaaUser -Filter 'AccountStatus -cmatch inacti'

# Get a local user, where AccountStatus matches with 'active' (starts with active or case sensitive).

Get-ImcManagedObject -ClassId aaaUser -Filter 'AccountStatus -cmatch ^active'

# Get a local user, where AccountStatus does not match 'active' (starts with active or case sensitive).

Get-ImcManagedObject -ClassId aaaUser -Filter 'AccountStatus -cnotmatch ^active'

# Get a local user, where Accountstatus is not 'active' (starts with active or case sensitive).

Get-ImcManagedObject -ClassId aaaUser -Filter 'AccountStatus -cnotlike active'

All the set and remove cmdlets in PowerTool, prompt for a confirmation, you can skip this confirmation by using -Force flag.

Get-ImcSnmpUser -Name snmpuser | Clear-ImcSnmpUser -Force

# PCI Adapter Properties

Get-ImcPciEquipSlot -Id “1”

# Network Adapter Information

Get-ImcNetworkAdapterEthIf -Dn “sys/rack-unit-1/network-adapter-L/eth-1”

# Storage Controller Information

Get-ImcStorageController -Dn “sys/rack-unit-1/board/storage-SAS-SLOT-4”

The Get-ImcKmipDownloadStatus cmdlet provides an option to get the download status of a KMIP entity like Root CA Certificate, Client Certificate, and Client Private Key.

Get-ImcKmipDownloadStatus [-Type <string>] [-XtraProperty <Hashtable>] [<CommonParameters>]

Get-ImcKmipDownloadStatus
Get-ImcKmipDownloadStatus -Type RootCACertificate
Get-ImcKmipDownloadStatus -Type ClientCertificate
Get-ImcKmipDownloadStatus -Type ClientPrivateKey

The Get-ImcKmipUploadStatus cmdlet provides an option to get the upload status of a KMIP entity like Root CA Certificate, Client Certificate, and Client Private Key.

Get-ImcKmipUploadStatus [-Type <string>] [-XtraProperty <Hashtable>] [<CommonParameters>]

Get-ImcKmipUploadStatus
Get-ImcKmipUploadStatus -Type RootCACertificate
Get-ImcKmipUploadStatus -Type ClientCertificate
Get-ImcKmipUploadStatus -Type ClientPrivateKey

Create a user credential, using the following cmdlet:

$user = "<username>"
$password = "<password>"
$cred = New-Object System.Management.Automation.PSCredential($user,$password)

Update HUU firmware, using the following cmdlet:

Set-ImcHuuFirmwareUpdater -AdminState trigger -MapType nfs -RemoteIp 10.105.219.83 
-RemoteCredential $cred-RemoteShare "/huuIso/ucs-c2x-huu-2.0.3d-1.iso" -StopOnError yes 
-TimeOut 60 -UpdateComponent All-VerifyUpdate no -force -Xml

NFS Mapping:

Get-ImcStorageFlexUtilVirtualDriveImageMap -VirtualDrive "HUU" | 
Set-ImcStorageFlexUtilVirtualDriveImageMap -AdminAction map -Map nfs -RemoteShare "x.x.x.x:/nfsShareLocation" 
-RemoteFile "ucs-c240m5-huu-3.1.3a.iso" -MountOptions "nolock" -Force

Update the mapped image to the HUU partition from specified mount location:

Get-ImcStorageFlexUtilVirtualDrive -PartitionName HUU | 
Set-ImcStorageFlexUtilVirtualDrive -AdminAction update-vd -Force

Update status can be found using the below query:

Get-ImcStorageFlexUtilVirtualDrive -PartitionName HUU | 
select OperationInProgress, LastOperationStatus,HostAccessible

Note	OperationInProgress: value should be Update-Success

Request to enable the virtual drive which would make the partition visible to the host:

Get-ImcStorageFlexUtilVirtualDrive -PartitionName HUU | 
Set-ImcStorageFlexUtilVirtualDrive -AdminAction enable-vd -Force

Note	HostAccessible: Value should be Connected

Get the LUN ID to set the boot order:

Get-ImcStorageFlexUtilVirtualDrive -PartitionName HUU | select LunId

Set the boot order to boot from flex-util HUU partition based on LUN ID:

Get-ImcLsbootSd | set-ImcLsbootSd -Lun <lunId selected in above cmdlet> 
-Order 1 -State enabled -Subtype flex-util -Force
Get-ImcLsbootDevPrecision | Set-ImcLsbootDevPrecision -RebootOnUpdate yes

Start HUU Firmware update process:

$user = "testUser"
$password = "testPassword" | ConvertTo-SecureString -AsPlainText -Force
$cred = New-Object System.Management.Automation.PSCredential($user,$password)
Set-ImcHuuFirmwareUpdater -AdminState trigger -MapType nfs -RemoteIp "NA" -RemoteCredential $cred -RemoteShare "NA" 
-StopOnError yes -TimeOut 120 -UpdateComponent All -VerifyUpdate no -BootMedium "microsd" -Force

Update security key/keyId for a drive security MO, using the following cmdlet:

Get-ImcStorageController |Set-ImcDriveSecurity -KeyId “newkey” -KeyManagement local -SecurityKey “password4321”
-ExistingSecurityKey “myPass123” –Force

# Enable SupportMultipleDefaultUcs to connect to multiple Cisco IMC, using the following cmdlet:

Set-UcsPowerToolConfiguration -SupportMultipleDefaultUcs $true

# Get the credential and store it in a variable, using the following cmdlet:

$secpasswd = ConvertTo-SecureString password -AsPlainText -Force
$mycreds = New-Object System.Management.Automation.PSCredential ("admin",$secpasswd)

# Connect to different Cisco IMC, using the following cmdlet:

$cimc1 = Connect-Imc xx.xx.xx.xx -Credential $mycreds
$cimc2 = Connect-Imc xx.xx.xx.xx -Credential $mycreds

# Get a local user from different Cisco IMC, using the following cmdlet:

$user1 = Get-ImcLocalUser -Imc $cimc1 -Id 1
$user2 = Get-ImcLocalUser -Imc $cimc2 -Id 1

# Synchronize a set of MOs from Cisco IMC2 to Cisco IMC1, using the following cmdlet:

Compare-ImcManagedObject $user1 $user2
Sync-ImcManagedObject (Compare-ImcManagedObject $user1 $user2) -Imc $cimc1

Modify the syslog settings, using the following cmdlet:

Get-ImcSyslog | Set-ImcSyslog -LocalSeverity warning -RemoteSeverity debug -Force

Generate a certificate signing request (CSR) to obtain a new certificate. You can upload the new certificate to the Cisco IMC to replace the current server certificate. A public Certificate Authority (CA), such as VeriSign, or by your own certificate authority certifies the server. The generated certificate key length is 2048 bits.

New-ImcCertificateSigningRequest -CommonName “CSR2” -CountryCode India -Locality “GG6” -Organization “cisco” -OrganizationalUnit “Tpidev” -Protocol ftp -State “Haryana” -RemoteFile “ImcCertificate.txt” -RemoteServer 10.105.219.xx -User administrator -Pwd *****

ConvertTo-ImcCmdlet:

Cisco IMC GUI does not support XML logging. To generate the ConvertTo-ImcCmdlet cmdlets, rely on the output of the Get cmdlet and generate cmdlets to replicate the same object hierarchy.

Generate cmdlets for the specified MOs.

Get-ImcBiosSettings -Hierarchy | ConvertTo-ImcCmdlet

Save the cmdlet output in a file.

Get-ImcBiosSettings -Hierarchy | ConvertTo-ImcCmdlet -OutputPath "C:/OutputFile.txt"

Gets the information of current certificate available on the Cisco IMC server.

Receive-ImcCertificate

The Receive-ImcKmipEntity cmdlet provides an option to download a KMIP entity like Root CA Certificate, Client Certificate, and Client Private Key.

Receive-ImcKmipEntity -Type <string> [-Protocol <string>] [-Pwd <string>] [-RemoteFile <string>] 
[-RemoteServer <string>] [-User <string>] [-XtraProperty <Hashtable>] [-Force] [<CommonParameters>]

Receive-ImcKmipEntity -Type RootCACertificate -RemoteServer 10.10.10.10 -User root -Pwd <password> 
-Protocol scp -RemoteFile "/root/test/RootCACertificate.pem" -Force
Receive-ImcKmipEntity -Type ClientCertificate -RemoteServer 10.10.10.10 -User root -Pwd <password> 
-Protocol scp -RemoteFile "/root/test/ClientCertificate.pem" -Force
Receive-ImcKmipEntity -Type ClientPrivateKey -RemoteServer 10.10.10.10 -User root -Pwd <password> 
-Protocol scp -RemoteFile "/root/test/ClientPrivateKey.pem" -Force

Exports the LDAP CA certificate from the IMC server to a remote server.

Get-ImcExportLdapCACertificate | Receive-ImcLdapCACertificate 
-Protocol scp -RemoteServer "10.10.10.10" -RemoteFile 
"/root/test/ExportFileLdapCACertificate.crt" -User 
"user" -Pwd "Password123" -Force

Removes the LDAP CA Certificate from the IMC server.

Get-ImcLdapCACertificate | Remove-ImcLdapCACertificate -Force

Resets event filters.

Get-ImcEventManagement | Reset-ImcEventFilters -Force
Get-ImcRackUnit | Reset-ImcEventFilters -Force

The Send-ImcBiosProfile cmdlet uploads the BIOS profile to the Cisco IMC. You can specify the profile details, such as IP/HostName, protocol, path and filename, username and password from a remote location.

Send-ImcBiosProfile -BiosProfileManagement <BiosProfileManagement> [-Protocol <string>] 
[-Pwd <string>] [-RemoteFile <string>] [-RemoteServer <string>] [-User <string>] [-XtraProperty <Hashtable>] 
[-Force] [<CommonParameters>]

Get-ImcBiosProfileManagement | Send-ImcBiosProfile -Protocol scp -User root -Pwd <password> 
-RemoteServer 10.10.10.10 -RemoteFile "/root/test/bios_profile_1" -Force

The Send-ImcKmipEntity cmdlet provides an option to upload a KMIP entity, like Root CA Certificate, Client Certificate, and Client Private Key.

Send-ImcKmipEntity -Type <string> [-Protocol <string>] [-Pwd <string>] [-RemoteFile <string>] 
[-RemoteServer <string>] [-User <string>] [-XtraProperty <Hashtable>] [-Force] [<CommonParameters>]

Send-ImcKmipEntity -Type RootCACertificate -RemoteServer 10.10.10.10 -User root -Pwd <password> 
-Protocol scp -RemoteFile "/root/test/RootCACertificate.pem" -Force
 
Send-ImcKmipEntity -Type ClientCertificate -RemoteServer 10.10.10.10 -User root -Pwd <password> 
-Protocol scp -RemoteFile "/root/test/ClientCertificate.pem" -Force
 
Send-ImcKmipEntity -Type ClientPrivateKey -RemoteServer 10.10.10.10 -User root -Pwd <password> 
-Protocol scp -RemoteFile "/root/test/ClientPrivateKey.pem" -Force

Uploads the LDAP CA certificate located at the remote server on the IMC server.

Get-ImcDownloadLdapCACertificate | Send-ImcLdapCACertificate 
-Protocol scp -RemoteServer "10.10.10.10" -RemoteFile "
/root/test/LDAPCACErtificate.cer" -User "user" -Pwd 
"Password123" -Force

Uploads the PID catalogue file located at the remote server on the IMC server.

Get-ImcPidCatalog | Send-ImcPidCatalog -Protocol scp 
-RemoteServer "10.10.10.10" -RemoteFile 
"/root/test/pid-ctlg-2_0_13a18.tar.gz" -User 
"user" -Pwd "Password123" -Force

Get-ImcUploadPIDCatalog | Send-ImcPidCatalog -Protocol scp 
-RemoteServer "10.10.10.10" -RemoteFile 
"/root/test/pid-ctlg-2_0_13a18.tar.gz" -User 
"user" -Pwd "Password123" -Force

The following table lists the new and changed cmdlets to perform server actions:

Set a physical drive as a boot drive, using the following cmdlet:

Get-ImcStorageLocalDisk -Id 2 | Set-ImcStorageLocalDisk -AdminAction "set-boot-drive" -Force

Set a virtual drive as a boot drive, using the following cmdlet:

Get-ImcStorageVirtualDrive -Id 2 | Set-ImcStorageVirtualDrive -AdminAction "set-boot-drive" -Force

Change Disk Mode (JBOD to UG and vice versa)

Get-ImcStorageController | Set-ImcStorageController -AdminAction enable-jbod -Force -Xml
get-ImcStorageLocalDisk -Id 3 | Set-ImcStorageLocalDisk -AdminAction make-jbod -Force
get-ImcStorageLocalDisk -Id 3 | Set-ImcStorageLocalDisk -AdminAction make-unconfigured-good -Force

Set the boot order, using the following cmdlet:

Get-ImcLsbootStorage | Set-ImcLsbootStorage -Order 2 -Force

Get-ImcLsbootDevPrecision | Add-ImcLsbootHdd -Name "RAID1_12" -Order 1 -State "Enabled" -Type "LOCALHDD"
Get-ImcLsbootDevPrecision | Add-ImcLsbootVMedia -Name "CIMCDVD" -Order 2 -State "Enabled" -Type "VMEDIA"
Get-ImcLsbootDevPrecision -Hierarchy | ConvertTo-ImcCmdlet

Note	Setting BIOS password feature is applicable for E-Series servers only.

Get-ImcBiosPassword | Set-ImcBiosPassword -Password "<password>" -Force

The Start-ImcOsInstallation cmdlet starts the NI-SCU operating system installation process.

Note	For details on how to create the configuration files, answer files, and so on, see to Cisco UCS C-Series Server Configuration Utility documentation.

Start-ImcOsInstallation -OsInstallation <OsiStart> [-AnswerFilePassword <string>] [-AnswerFileShareFile <string>] 
[-AnswerFileShareIp <string>] [-AnswerFileSharePath <string>] -AnswerFileShareType <string> [-AnswerFileUsername
<string>] [-ConfigShareFile <string>] [-ConfigShareIp <string>] [-ConfigSharePassword <string>] 
[-ConfigSharePath <string>] -ConfigShareType <string> [-ConfigShareUsername <string>] -IsoShare <string> [-IsoShareIp <string>]
-IsoShareType <string> [-Password <string>] [-RemoteShareFile <string>] [-RemoteShareIp <string>] 
[-RemoteSharePassword <string>] [-RemoteSharePath <string>] -RemoteShareType <string> [-RemoteShareUsername <string>] [-TimeOut
<uint>] [-Username <string>] [-XtraProperty <Hashtable>] [-Force] [<CommonParameters>]


Start-ImcOsInstallation -OsInstallationController <OsiController> [-AnswerFilePassword <string>] 
[-AnswerFileShareFile <string>] [-AnswerFileShareIp <string>] [-AnswerFileSharePath <string>] -AnswerFileShareType <string>
[-AnswerFileUsername <string>] [-ConfigShareFile <string>] [-ConfigShareIp <string>] 
[-ConfigSharePassword <string>] [-ConfigSharePath <string>] -ConfigShareType <string> 
[-ConfigShareUsername <string>] -IsoShare <string>
[-IsoShareIp <string>] -IsoShareType <string> [-Password <string>] [-RemoteShareFile <string>] 
[-RemoteShareIp <string>] [-RemoteSharePassword <string>] [-RemoteSharePath <string>] -RemoteShareType <string> [-RemoteShareUsername
<string>] [-TimeOut <uint>] [-Username <string>] [-XtraProperty <Hashtable>] [-Force] [<CommonParameters>]

Get-ImcOsInstallation | Start-ImcOsInstallation -AnswerFileShareIp 10.10.10.10 
-AnswerFileUsername root -AnswerFilePassword <password> -AnswerFileSharePath "/root/test/osi" 
-AnswerFileShareFile "" -AnswerFileShareType scp -ConfigShareIp 10.10.10.10 -ConfigShareUsername root 
-ConfigSharePassword <password> -ConfigSharePath "/root/test/osi" -ConfigShareFile "conf_file1" -ConfigShareType scp 
-IsoShareIp 11.11.11.11 -IsoShare "/nfsshare/ucs-cxxx-scu-5.0.1a.iso" -IsoShareType nfs -Username administrator 
-Password <password> -RemoteShareIp 10.10.10.10 -RemoteShareUsername root -RemoteSharePassword <password> 
-RemoteSharePath "/root/test/osi" -RemoteShareFile "" -RemoteShareType scp -Force


Get-ImcOsInstallationController | Start-ImcOsInstallation -AnswerFileShareIp 10.10.10.10 
-AnswerFileUsername root -AnswerFilePassword <password> -AnswerFileSharePath "/root/test/osi" 
-AnswerFileShareFile "" -AnswerFileShareType scp -ConfigShareIp 10.10.10.10 -ConfigShareUsername root 
-ConfigSharePassword <password> -ConfigSharePath "/root/test/osi" -ConfigShareFile "conf_file1" 
-ConfigShareType scp -IsoShareIp 11.11.11.11 -IsoShare "/nfsshare/ucs-cxxx-scu-5.0.1a.iso" 
-IsoShareType nfs -Username administrator -Password <password> -RemoteShareIp 10.10.10.10 
-RemoteShareUsername root -RemoteSharePassword <password> -RemoteSharePath "/root/test/osi" -RemoteShareFile "" -RemoteShareType scp -Force

Tests the LDAP Binding on the IMC server

Get-ImcLdapCACertificate | Test-ImcLdapBinding -User "user" 
-Pwd "Password123" -Force

# Start a transaction, using the following cmdlet:

Start-ImcTransaction

# Perform an operation, using the following cmdlets:

$adapterHostEthIf = Get-ImcadapterUnit | Add-ImcadapterHostEthIf -Name adapterHostEth
$adapterHostEthIfModify = $adapterHostEthIf | Set-ImcadapterHostEthIf -PxeBoot enabled
$adapterEthISCSIProfile = $adapterHostEthIfModify | Add-ImcadapterEthISCSIProfile -InitiatorName adapterHostEth -InitiatorIPAddress xx.xx.xx.xx -InitiatorSubnetMask 255.255.255.0 -DhcpISCSI enabled
$adapterEthISCSIProfile | Remove-ImcadapterEthISCSIProfile
$adapterHostEthIfModify | Remove-ImcadapterHostEthIf

# End a transaction, using the following cmdlet:

Complete-ImcTransaction

# Undo a transaction, using the following cmdlet:

Undo-ImcTransaction

Configure vMedia, using the following cmdlet:

Get-ImcCommVMedia | Set-ImcCommVMedia -AdminState “enabled” -EncryptionState “enabled” -Force

Create vNIC/Adapter

Get-ImcAdaptorUnit -Id "1" | Add-ImcAdaptorHostEthIf  -Name "eth2"  -UplinkPort "0"

Cisco UCS Communities is a platform to discuss, share, and learn about the Cisco Products and Technologies. For blogs, discussion forums and documents related to UCS integrations with Cisco UCS Communities partner ecosystem, visit https://communities.cisco.com/ucsintegrations .