Cisco Catalyst PON Series Switches OLT Command Reference

alarm all-packets

To enable alarms on all ports, use the alarm all-packets command in global configuration mode.

To enable alarms on a specific port, use the alarm all-packets command in interface configuration mode.

alarm all-packets

no alarm all-packets

Command Modes

Global configuration (config)

Interface configuration (config-if)

Examples

The following example shows how to enable alarms on all ports of the device:

Device> enable
Device# configure terminal
Device(config)# alarm all-packets
Enable port alarm successfully.

alarm all-packets threshold

To configure the port threshold information for alarms, use the alarm all-packets threshold command in interface configuration mode.

alarm all-packets threshold {normal normal-value | exceed exceed-value}

Syntax Description


normal `normal-value`	Sets the minimum port bandwidth utilization threshold for the port.
exceed `exceed-value`	Sets the maximum port bandwidth utilization threshold for the port.

Command Modes

Interface configuration mode (config-if)

Examples

The following example shows how to set the port thresholds using the alarm all-packets threshold command:

Device> enable
Device# configure terminal
Device(config)# interface gpon 0/1
Device(config-if-gpon-0/1)# alarm all-packets threshold exceed 34 normal 4

alarm cpu

To enable CPU alarms, use the alarm cpu command in global configuration mode.

alarm cpu

no alarm cpu

Command Modes

Global configuration mode (config)

Examples

The following example shows how to enable CPU alarms:

Device> enable
Device# configure terminal
Device(config)# alarm cpu

alarm cpu threshold

To configure the threshold information for CPU alarms, use the alarm cpu threshold command in global configuration mode.

alarm cpu threshold {busy busy-value | unbusy unbusy-value}

Syntax Description


busy `busy-value`	Sets the minimum CPU utilization threshold.
unbusy `unbusy-value`	Sets the maximum CPU utilization threshold.

Command Modes

Global configuration mode (config)

Examples

The following example shows how to set the CPU thresholds using the alarm cpu threshold command:

Device> enable
Device# configure terminal
Device(config)# alarm cpu threshold busy 63 unbusy 20

buildrun mode

To configure the file execution mode, use the buildrun mode command in privileged EXEC mode.

buildrun mode {continue | stop}

Syntax Description


continue	Sets the execution mode to non-interruptible.
stop	Sets the execution mode to interruptible.

Command Modes

Privileged EXEC (#)

Examples

The following is an example of the buildrun mode stop command:

Device> enable
Device# buildrun mode stop

clear startup-config

To clear the startup configuration, use the clear startup-config command in privileged EXEC mode.

clear startup-config

Command Modes

Privileged EXEC (#)

Examples

The following is an example of the clear startup-config command:

Device> enable
Device# clear startup-config

clock summer-time

To set the clock daylight savings time, use the clock summer-time command in global configuration mode.

clock summer-time { dayly | weekly } start-time

Syntax Description


`start-time`	Specifies the start time for daylight savings. The daylight savings time format must be entered in hour, minutes and, seconds (HH:MM:SS).

Command Modes

Global configuration mode (config)

Examples

The following example shows how to configure the daylight savings using the clock summer-time command:

Device> enable
Device# configure terminal
Device(config)# clock summer-time dayly 00:00:00 2021/03/12 00:00:00 2021/11/05

clock timezone

To configure the system time zone, use the clock timezone command in global configuration mode.

clock timezone timezone-name hours-offset minutes-offset

no clock timezone

Syntax Description


`timezone-name`	Specifies the timezone to the SNTP client.
`hours-offset minutes-offset`	Specifies the hours and minutes offset from the timezone to the SNTP client.

Command Modes

Global configuration mode (config)

Examples

The following example shows how to configure a timezone on the SNTP client using the clock timezone command:

Device> enable
Device# configure terminal
Device(config)# clock timezone ch 3 43

copy running-config startup-config

To copy the current configuration to the flash config file, use the copy running-config startup-config command in privileged EXEC mode.

copy running-config startup-config

Command Modes

Privileged EXEC (#)

Examples

The following is an example of the copy running-config startup-config command:

Device> enable
Device# copy running-config startup-config 
Startup config in flash will be updated, are you sure(y/n)? [n]

copy startup-config running-config

To copy the startup configuration from the flash config file to the current configuration, use the copy startup-config running-config command in privileged EXEC mode.

copy startup-config running-config

Command Modes

Privileged EXEC (#)

Examples

The following is an example of the copy startup-config running-config command:

Device> enable
Device# copy startup-config running-config 
Running config will be updated, are you sure(y/n)? [n]

load ftp

To download a file with the FTP server, use the load ftp command in privileged EXEC mode.

load {application | configuration | edfa | epld | keyfile {private | public} | ont-image | whole-bootrom}ftp {inet | inet6}ftp-server-ip-address file-name ftp-username ftp-password

Syntax Description


application	Specifies the host file.
configuration	Specifies the configuration file.
edfa	Specifies the EDFA file.
epld	Specifies the EPLD file.
keyfile	Specifies the SSH keyfile.
private	Specifies the SSH private keyfile.
public	Specifies the SSH public keyfile.
ont-image	Specifies the ONT image file.
whole-bootrom	Specifies the whole bootrom file.
inet	Specifies IPv4 address family.
inet6	Specifies IPv6 address family.
`ftp-server-ip-address`	Specifies the IP address of the FTP server.
`file-name`	Specifies the name of the file to be uploaded.
`ftp-username`	Specifies the user name of the FTP server.
`ftp-password`	Specifies the password of the FTP server.

Command Modes

Privileged EXEC (#)

Examples

The following example shows how to download a whole bootrom file with an FTP server using the load ftp command:

Device> enable
Device# load whole-bootrom tftp inet 10.23.13.1 bootrom1.bin

load tftp

To download a file with the TFTP server, use the load tftp command in privileged EXEC mode.

load {application | configuration | edfa | epld | keyfile {private | public} | ont-image | whole-bootrom}tftp {inet | inet6}tftp-server-ip-address file-name

Syntax Description


application	Specifies the host file.
configuration	Specifies the configuration file.
edfa	Specifies the EDFA file.
epld	Specifies the EPLD file.
keyfile	Specifies the SSH keyfile.
private	Specifies the SSH private keyfile.
public	Specifies the SSH public keyfile.
ont-image	Specifies the ONT image file.
whole-bootrom	Specifies the whole bootrom file.
inet	Specifies IPv4 address family.
inet6	Specifies IPv6 address family.
`tftp-server-ip-address`	Specifies the IP address of the TFTP server.
`file-name`	Specifies the name of the file to be uploaded.

Command Modes

Privileged EXEC (#)

Examples

The following example shows how to download a whole bootrom file with a TFTP server using the load tftp command:

Device> enable
Device# load whole-bootrom tftp inet6 10:23::11:1 bootrom1.bin

load xmodem

To download a file with the XMODEM, use the load ftp command in privileged EXEC mode.

load {application | configuration | whole-bootrom}xmodem

Syntax Description


application	Specifies the host file.
configuration	Specifies the configuration file.
whole-bootrom	Specifies the whole bootrom file.

Command Modes

Privileged EXEC (#)

Examples

The following example shows how to download a whole bootrom file with an XMODEM using the load xmodem command:

Device> enable
Device# load whole-bootrom xmodem

local fec

To enable the ONT uplink FEC, use the local fec command in line profile configuration mode. To disable the ONT uplink FEC, use the no local fec command.

local fec

no local fec

Command Modes

Line profile configuration (deploy-profile-line)

Examples

This example shows how to enable the ONT uplink FEC

Device> enable
Device# configure terminal
Device(config)# deploy profile line
Device(config-profile-line)# aim 5
Device(config-profile-line-5)# local fec

ntp access

To configure access control for Network Time Protocol (NTP) services, use the ntp access command in global configuration mode. To disable NTP settings, use the no access form of the command.

ntp access ip-address { permit | deny }

no ntp access ip-address { permit | deny }

Syntax Description


access `ip-address`	Specifies the control access for an IPv4 or IPv6 access list to the NTP services.
permit	Permts the NTP services.
deny	Denies the NTP services

Command Modes

Global configuration (config)

Examples

The following example shows how to enable NTP authentication using the ntp access command:

Device> enable
Device# configure terminal
Device(config)# ntp access 192.168.0.10 255.255.255.0 permit

ntp authentication

To enable NTP authentication and configure NTP settings, use the ntp authenticatiom command in global configuration mode. To disable NTP settings, use the no form of the command.

ntp authentication authentication-keyid key_id md5 key_string

no ntp authentication authentication-keyid key_id md5 key_string

Syntax Description


authentication	Enables NTP authentication.
authentication-keyid `key_id` md5 `key_string`	Specifies an authentication key for a trusted NTP source. `key_id`: The authentication key. The range is from 1 to 65535. md5 : Message Digest 5 (MD5) algorithm authentication support `key_string` : Key value. The maximum length is 32 characters.

Command Modes

Global configuration (config)

Examples

The following example shows how to enable NTP authentication using the ntp authentication command:

Device> enable
Device# configure terminal
Device(config)# ntp authentication

ntp broadcast

To configure NTP broadcast mode, use the ntp broadcast command in interface configuration mode. To disable NTP settings, use the no form of the command.

ntp broadcast { server authentication-keyid key_id | client }

no ntp broadcast { server authentication-keyid key_id | client }

Syntax Description


authentication-keyid `key_id`	Specifies an authentication key for a trusted NTP source. `key_id`: The authentication key. The range is from 1 to 65535.

Command Modes

Interface configuration (config-if)

Examples

The following example shows how to configure the NTP broadcast mode using ntp broadcast command:

Device> enable
Device# configure terminal
Device(config)# interface vlan-interface 1
Device(config-if-vlaninterface-1)# ntp broadcast server

ntp disable

To disable NTP incoming packets, use the ntp disable command in interface configuration mode. To disable NTP settings, use the no form of the command.

ntp disable

no ntp disable

Command Modes

Interface configuration (config-if)

Examples

The following example shows how to disable NTP incoming packets using the ntp disable command:

Device> enable
Device# configure terminal
Device(config)# interface vlan-interface 1
Device(config-if-vlaninterface-1)# ntp disable

ntp max-dynamic-sessions

To configure maximum number of dynamic NTP sessions, use the ntpmax-dynamic-sessions command in global configuration mode. To disable NTP settings, use the no form of the command.

ntp max-dynamic-sessions value

no ntp max-dynamic-sessions value

Syntax Description


max-dynamic-sessions `value`	Specifies the maximum number of dynamic sessions. `value` : The range is from 11 to 100.

Command Modes

Interface configuration (config-if)

Examples

The following example shows how to configure maximum number of dynamic NTP sessions using the ntp authentication command:

Device> enable
Device# configure terminal
Device(config)# ntp max-dynamic-sessions 10

ntp multicast

To configure NTP multicast mode, use the ntp multicast command in global configuration mode. To disable NTP settings, use the no form of the command.

ntp multicast { server authentication-keyid key_id | client }

no ntp multicast { server authentication-keyid key_id | client }

Syntax Description


authentication-keyid `key_id`	Specifies an authentication key for a trusted NTP source. `key_id`: The authentication key. The range is from 1 to 65535.

Command Modes

Interface configuration (config-if)

Examples

The following example shows how to configure the NTP multicast mode using ntp multicast command:

Device> enable
Device# configure terminal
Device(config)# interface vlan-interface 1
Device(config-if-vlaninterface-1)# ntp multicast server

ntp unicast peer

To configure synchronization to an NTP-configured peer device, use the ntp unicast peer command in global configuration mode. To disable NTP settings, use the no form of the command.

ntp unicast peer ip-address [ authentication-keyid key_id ]

no ntp unicast peer ip-address [ authentication-keyid key_id ]

Syntax Description


peer `ip-address`	Specifies the system clock to synchronize a peer or to be synchronized by a peer `ip-address` : IPv4 or IPv6 address of the peer device.

Command Modes

Global configuration (config)

Examples

The following example shows how to configure synchronization to an NTP-configured peer device using the ntp unicast peer command:

Device> enable
Device# configure terminal
Device(config)# ntp unicast peer 192.168.0.10

ntp unicast server

To configure client mode, use the ntp unicast server command in global configuration mode. To disable NTP settings, use the no form of the command.

ntp unicast server ip-address [ authentication-keyid key_id ]

no ntp unicast server ip-address [ authentication-keyid key_id ]

Syntax Description


server`ip-address`	Specifies the system clock to be synchronized by a time server. `ip-address` : IPv4 or IPv6 address of the time server.

Command Modes

Global configuration (config)

Examples

The following example shows how to configure client mode using the ntp unicast server command:

Device> enable
Device# configure terminal
Device(config)# ntp unicast server  192.168.0.11

show alarm all-packets

To display the port alarm information, use the show alarm all-packets command in global configuration mode or interface configuration mode.

show alarm all-packets [interface port-number]

Syntax Description


interface `port-number`	Specifies the interface.

Command Modes

Global configuration mode (config)

Interface configuration mode (config-if)

Examples

Device> enable
Device# configure terminal
Device(config)# show ntp unicast server

show running-config

To display the current system configuration, use the show running-config command in the privileged EXEC mode or global configuratoin mode.

show running-config {module | interface {ethernet port-id | gpon port-id | loopback-interface loopback-interface-number | vlan-interface vlan-id}}perlines lines-per-page

Syntax Description


`module`	Specifies a module.
interface	Specifies an interface.
ethernet `port-id`	Displays the ethernet port configuration.
gpon `port-id`	Displays the GPON port configuration.
loopback-interface `loopback-interface-number`	Displays the loopback interface configuration.
vlan-interface `vlan-id`	Displays the VLAN configuration.
perlines `lines-per-page`	Specifies the number of lines displayed per page.

Command Modes

Privileged EXEC (#)

Global configuration mode (config)

Examples

The following is a sample output from the show running-config interface vlan-interface command:

Device> enable
Device# show running-config interface vlan-interface

Building configuration...
![vlan-interface 1]
ip address range 192.0.2.254 192.0.2.255
description interface1
![vlan-interface 100]
ip address 10.75.171.17 255.255.255.0
end

show sntp client

To display SNTP client configurations, use the show sntp client command in global configuration mode.

show sntp client

Command Modes

Global configuration mode (config)

Examples

The following is a sample output of the show sntp client command:

Device> enable
Device# configure terminal
Device(config)# show sntp client
Clock state : synchronized         Current mode : anycast
Use server : 192.168.1.99          State : idle
Server state : synchronized        Server stratum : 1
Retrans-times: 3                   Retrans-interval: 30s
Authenticate : enable              Authentication-key: 1
Poll interval : 1000s
Last synchronized time: THU NOV 26 09:22:25 2015

show startup-config

To display the startup configuration, use the show startup-config command in the privileged EXEC mode or global configuratoin mode.

show startup-config {module | interface {ethernet port-id | gpon port-id | loopback-interface loopback-interface-number | vlan-interface vlan-id}}perlines lines-per-page

Syntax Description


`module`	Specifies a module.
interface	Specifies an interface.
ethernet `port-id`	Displays the ethernet port configuration.
gpon `port-id`	Displays the GPON port configuration.
loopback-interface `loopback-interface-number`	Displays the loopback interface configuration.
vlan-interface `vlan-id`	Displays the VLAN configuration.
perlines `lines-per-page`	Specifies the number of lines displayed per page.

Command Modes

Privileged EXEC (#)

Global configuration mode (config)

Examples

The following is a sample output from the show startup-config interface ethernet command:

Device> enable
Device# show startup-config interface ethernet

Building configuration...
![ethernet 1/1]
channel-group 2 mode on
lacp port-priority 8
description text
switchport hybrid untagged vlan 2-125
igmp-snooping record-host
ip-source-guard ip-mac-vlan
![ethernet 1/2]
switchport hybrid tagged vlan 35,335
switchport hybrid untagged vlan 2-34,36-125,2501-2502
![ethernet 1/3]
switchport default vlan 100
switchport hybrid untagged vlan 2-125
![ethernet 1/4]
priority 2
![ethernet 2/1]
switchport hybrid untagged vlan 2-125
![ethernet 2/2]
switchport hybrid untagged vlan 2-125
end

sntp client

To enable SNTP client, use the sntp client command in global configuration mode.

sntp client

no sntp client

Command Modes

Global configuration mode (config)

Examples

The following example shows how to enable SNTP client:

Device> enable
Device# configure terminal
Device(config)# sntp client

sntp client authenticate

To enable authentication of time sources, use the sntp client authenticate command in global configuration mode.

sntp client authenticate

no sntp client authenticate

Command Modes

Global configuration mode (config)

Examples

The following example shows how to enable SNTP client authentication using the sntp client authenticate command:

Device> enable
Device# configure terminal
Device(config)# sntp client authenticate

sntp client authentication-key

To configure the password for authentication for trusted time sources, use the sntp client authentication-key command in global configuration mode.

sntp client authentication-key key-number md5 md5-key

no sntp client authentication-key key-number

Syntax Description


`key-number`	Specifies the authentication key for the SNTP client.
md5 `md5-key`	Specifies the MD5 authentication key for the SNTP client.

Command Modes

Global configuration mode (config)

Examples

The following example shows how to configure SNTP client authentication using the sntp client authentication-key command:

Device> enable
Device# configure terminal
Device(config)# sntp client authentication-key 3 md5 5

sntp client broadcastdelay

To configure the broadcast propagation delay for an SNTP client, use the sntp client broadcastdelay command in global configuration mode.

sntp client broadcastdelay delay-time

Syntax Description


`delay-time`	Specifies the round-trip broadcast delay for the SNTP client in milliseconds.

Command Modes

Global configuration mode (config)

Examples

The following example show how to configure the delay time for the SNTP client using the sntp client broadcastdelay command:

Device> enable
Device# configure terminal
Device(config)# sntp client broadcastdelay 15

sntp client mode

To configure the mode of function of the SNTP client, use the sntp client mode command in global configuration mode.

sntp client mode {anycast { [key key-id]} | broadcast | multicast | unicast}

Syntax Description


anycast	Sets the SNTP client to work in anycast mode.
key `key-id`	Specifies the authentication key for anycast mode.
broadcast	Sets the SNTP client to work in broadcast mode.
multicast	Sets the SNTP client to work in multicast mode.
unicast	Sets the SNTP client to work in unicast mode.

Command Modes

Global configuration mode (config)

Examples

The following example show how to configure the SNTP client to unicast mode using the sntp client mode command:

Device> enable
Device# configure terminal
Device(config)# sntp client mode unicast

sntp client poll-interval

To configure the polling interval for an SNTP client, use the sntp client poll-interval command in global configuration mode.

sntp client poll-interval poll-interval-time

Syntax Description


`poll-interval-time`	Specifies the polling interval for the SNTP client in seconds.

Command Modes

Global configuration mode (config)

Examples

The following example show how to configure the polling interval for the SNTP client using the sntp client poll-interval command:

Device> enable
Device# configure terminal
Device(config)# sntp client poll-interval 800

sntp client retransmit-interval

To configure the timeout retransmission interval for an SNTP client, use the sntp client retransmit-interval command in global configuration mode.

sntp client retransmit-interval retransmit-interval-time

Syntax Description


`retransmit-interval-time`	Specifies the timeout retransmission interval for the SNTP client in seconds.

Command Modes

Global configuration mode (config)

Usage Guidelines

The configured timeout retransmission mechanism takes effect only when the SNTP client works in the unicast or anycast mode.

Examples

The following example show how to configure the retransmission interval for the SNTP client using the sntp client retransmit-interval command:

Device> enable
Device# configure terminal
Device(config)# sntp client retransmit-interval 8

sntp client retransmit

To configure the number of timeout retransmission attempts for an SNTP client, use the sntp client retransmit command in global configuration mode.

sntp client retransmit number

Syntax Description


`number`	Specifies the number of timeout retransmission attempts for the SNTP client.

Command Modes

Global configuration mode (config)

Usage Guidelines

The configured timeout retransmission mechanism takes effect only when the SNTP client works in the unicast or anycast mode.

Examples

The following example show how to configure the number of retransmission attempts for the SNTP client using the sntp client retransmit-interval command:

Device> enable
Device# configure terminal
Device(config)# sntp client retransmit 5

sntp client valid-server

To configure a legal server list for the SNTP client, use the sntp client valid-server command in global configuration mode.

sntp client valid-server ip-address wildcard-ip-address

no sntp client valid-server {all | ip-address wildcard-ip-address}

Syntax Description


`ip-address`	Specifies the IP address of the valid SNTP server.
`wildcard-ip-address`	Specifies the IP address of the wildcard SNTP server.

Command Modes

Global configuration mode (config)

Examples

The following example shows how to configure the valid SNTP servers for an SNTP client using the sntp client valid-server command:

Device> enable
Device# configure terminal
Device(config)# sntp client valid-server 10.23.23.1 23.1.1.4

sntp server

To set SNTP server configurations, use the sntp server command in global configuration mode.

sntp server {ip-address | backup ip-address | key key-number}

Syntax Description


`ip-address`	Specifies the IP address of the SNTP server.
backup `ip-address`	Specifies the IP address of the SNTP backup server.
key `key-number`	Specifies the authentication key for the SNTP server.

Command Modes

Global configuration mode (config)

Examples

The following example shows how to configure the SNTP server using the sntp server command:

Device> enable
Device# configure terminal
Device(config)# sntp server 12.2.2.1

sntp trusted-key

To configure a trusted password for multicast and broadcast modes, use the sntp trusted-key command in global configuration mode.

sntp trusted-key key-number

no sntp trusted-key key-number

Syntax Description


`key-number`	Specifies the trusted key for the SNTP client.

Command Modes

Global configuration mode (config)

Examples

The following example shows how to configure SNTP client trusted key authentication using the sntp trusted-key command:

Device> enable
Device# configure terminal
Device(config)# sntp trusted-key 243586

upload automatically configuration ftp

To automatically upload a configuration file at regular intervals with the FTP server, use the upload automatically configuration ftp command in privileged EXEC mode.

upload automatically configuration ftp {inet | inet6}ftp-server-ip-address file-name ftp-username ftp-passwordper hours hours minutes minutes

Syntax Description


inet	Specifies IPv4 address family.
inet6	Specifies IPv6 address family.
`ftp-server-ip-address`	Specifies the IP address of the FTP server.
`file-name`	Specifies the name of the file to be uploaded.
`ftp-username`	Specifies the user name of the FTP server.
`ftp-password`	Specifies the password of the FTP server.
per hours `hours` minutes `minutes`	Specifies the time interval in hours and minutes after which the configuration file is to be automatically uploaded.

Command Modes

Privileged EXEC (#)

Examples

The following example shows how to upload a configuration file using the upload automatically configuration tftp command:

Device> enable
Device# upload automatically configuration ftp inet 10.23.13.1 config3.txt per hours 12 minutes 10

upload automatically configuration tftp

To automatically upload a configuration file at regular intervals with the TFTP server, use the upload automatically configuration tftp command in privileged EXEC mode.

upload automatically configuration tftp {inet | inet6}tftp-server-ip-address file-name per hours hours minutes minutes

Syntax Description


inet	Specifies IPv4 address family.
inet6	Specifies IPv6 address family.
`tftp-server-ip-address`	Specifies the IP address of the TFTP server.
`file-name`	Specifies the name of the file to be uploaded.
per hours `hours` minutes `minutes`	Specifies the time interval in hours and minutes after which the configuration file is to be automatically uploaded.

Command Modes

Privileged EXEC (#)

Examples

The following example shows how to upload a configuration file using the upload automatically configuration tftp command:

Device> enable
Device# upload automatically configuration tftp inet 10.23.13.1 config2.txt per hours 20 minutes 30

upload ftp

To upload a file with the FTP server, use the upload ftp command in privileged EXEC mode.

upload {application | configuration | keyfile {private | public} | logging}ftp {inet | inet6}ftp-server-ip-address file-name ftp-username ftp-password

Syntax Description


application	Specifies the host file.
configuration	Specifies the configuration file.
keyfile	Specifies the SSH keyfile.
private	Specifies the SSH private keyfile.
public	Specifies the SSH public keyfile.
logging	Specifies the log file.
inet	Specifies IPv4 address family.
inet6	Specifies IPv6 address family.
`ftp-server-ip-address`	Specifies the IP address of the FTP server.
`file-name`	Specifies the name of the file to be uploaded.
`ftp-username`	Specifies the user name of the FTP server.
`ftp-password`	Specifies the password of the FTP server.

Command Modes

Privileged EXEC (#)

Examples

The following example shows how to upload a host file with an FTP server using the upload ftp command:

Device> enable
Device# upload application ftp 192.168.1.99 host.arj rr 142

upload tftp

To upload a file with the TFTP server, use the upload tftp command in privileged EXEC mode.

upload {application | configuration | keyfile {private | public} | logging}tftp {inet | inet6}tftp-server-ip-address file-name

Syntax Description


application	Specifies the host file.
configuration	Specifies the configuration file.
keyfile	Specifies the SSH keyfile.
private	Specifies the SSH private keyfile.
public	Specifies the SSH public keyfile.
logging	Specifies the log file.
inet	Specifies IPv4 address family.
inet6	Specifies IPv6 address family.
`tftp-server-ip-address`	Specifies the IP address of the TFTP server.
`file-name`	Specifies the name of the file to be uploaded.

Command Modes

Privileged EXEC (#)

Examples

The following example shows how to upload a configuration file with a TFTP server using the upload tftp command:

Device> enable
Device# upload application tftp 192.168.1.99 text.txt

Bias-Free Language

Results

Chapter: System Management

System Management

alarm all-packets

Command Modes

Examples

alarm all-packets threshold

Syntax Description

Command Modes

Examples

alarm cpu

Command Modes

Examples

alarm cpu threshold

Syntax Description

Command Modes

Examples

buildrun mode

Syntax Description

Command Modes

Examples

clear startup-config

Command Modes

Examples

clock summer-time

Syntax Description

Command Modes

Examples

clock timezone

Syntax Description

Command Modes

Examples

copy running-config startup-config

Command Modes

Examples

copy startup-config running-config

Command Modes

Examples

load ftp

Syntax Description

Command Modes

Examples

load tftp

Syntax Description

Command Modes

Examples

load xmodem

Syntax Description

Command Modes

Examples

local fec

Command Modes

Examples

ntp access

Syntax Description

Command Modes

Examples

ntp authentication

Syntax Description

Command Modes

Examples

ntp broadcast

Syntax Description

Command Modes

Examples

ntp disable

Command Modes

Examples

ntp max-dynamic-sessions

Syntax Description

Command Modes

Examples

ntp multicast

Syntax Description

Command Modes

Examples

ntp unicast peer

Syntax Description