OLT Port Configuration

channel-group group_id

To configure the aggregation group ID, use the channel-group channel_group_id command in global configuration mode. To disable the aggregation group ID, use the no channel-group channel_group_id command.

channel-group channel_group_id

no channel-group channel_group_id

Syntax Description

channel_group_id

The channel group ID.

The range is 0-5.

Command Modes

Global configuration (config)

Examples

This example shows how to configure the aggregation group ID

Device> enable
Device# configure terminal
Device(config)# channel-group 4

channel-group load-balance

To configure a load balance policy, use the channel-group load-balance command in global configuration mode. To disable a load balance policy, use the no channel-group load-balance form of this command.

channel-group load-balance {dst-ip | dst-mac | src-dst-ip | src-dst-mac | src-ip | src-mac}

no channel-group load-balance

Syntax Description

dst-ip

Configures the load balance policy based on destination IP.

dst-mac

Configures the load balance policy based on destination MAC.

src-dst-ip

Configures the load balance policy based on source and destination IP.

src-dst-mac

Configures the load balance policy based on source and destination MAC.

src-ip

Configures the load balance policy based on source IP.

src-mac

Configures the load balance policy based on source MAC.

Command Modes

Global configuration (config)

Examples

This example shows how to configure a load balance policy based on source MAC.

Device> enable
Device# configure terminal
Device(config)# channel-group load-balance src-mac

channel-group group_id mode

To add a port to an aggregation group, use the channel-group channel_group_id mode command in interface configuration mode. To disable the aggregation group ID, use the no channel-group channel_group_id mode command.

channel-group channel_group_id mode {on | active | passive}

no channel-group channel_group_id mode

Syntax Description

channel_group_id

The channel group ID.

The range is 0-5.
on

Configures the LACP static mode.
active

Configures the LACP active mode
passive

Configures the LACP passive mode

Command Modes

Interface configuration (config-if)

Examples

This example shows how to add a port to an aggregation group.

Device> enable
Device# configure terminal
Device(config)# interface ethernet 1/1
Device(config-if-ethernet-1/1)# channel-group 2 mode active

clear channel-group

To clear the LACP statistical information, use the clear channel-group channel_group_id command in global configuration mode.

clear channel-group [channel_group_id]

Syntax Description

channel_group_id

The channel group ID.

The range is 0-5.

Command Modes

Global configuration (config)

Examples

This example shows how to clear the LACP statistical information.

Device> enable
Device# configure terminal
Device(config)# clear channel-group
Clear channel group statistics information record successfully.

clear interface

To clear interface statistics information, use the clear interface command in global configuration mode.

clear interface {slot-number | ethernet slot-number/port-number | gpon slot-number/port-number }

Syntax Description

slot-number

The slot number.

The range is from 0 to 3.
slot-number/port-number

The port ID.

  • slot-number :

    • GPON: The value is 0.

    • GE Ethernet: The value is 1.

    • 10GE Ethernet: The value is 2.

  • port-number :

    • GPON: The range is from 1 to 8.

    • GE Ethernet: The range is from 1 to 4.

    • 10GE Ethernet: The range is from 1 to 2.

Command Modes

Global configuration (config)

Examples

This example shows how to clear interface statistics information

Device> enable
Device# configure terminal
Device(config)# clear interface ethernet 0/1
clear ports statistics information record successfully.

interface range ethernet

To configure port mode in bulk, use the interface range ethernet command in interface configuration mode.

interface range ethernet slot-number/port-number to ethernet slot-number/port-number

Syntax Description

slot-number/port-number

The port ID.

  • slot-number :

    • GPON: The value is 0.

    • GE Ethernet: The value is 1.

    • 10GE Ethernet: The value is 2.

  • port-number :

    • GPON: The range is from 1 to 8.

    • GE Ethernet: The range is from 1 to 4.

    • 10GE Ethernet: The range is from 1 to 2.

Command Modes

Interface configuration (config-if)

Examples

This example shows how to configure port mode in bulk

Device> enable
Device# configure terminal
Device(config)# interface ethernet 1/1
Device(config-if-ethernet-1/1)# interface range ethernet 1/1 to ethernet 1/4
Device(config-if-range)#

lacp port-priority

To configure port priority, use the lacp port-priority command in interface configuration mode. To disable port priority, use the no lacp port-priority command.

lacp port-priority priority_value

no lacp port-priority

Syntax Description

priority_value

The priority value.

The range is from 1 to 65535.

Command Modes

Interface configuration (config-if)

Examples

This example shows how to configure port priority.

Device> enable
Device# configure terminal
Device(config)# interface ethernet 1/1
Device(config-if-ethernet-1/1)# lacp port-priority 8

lacp system-priority

To configure system priority, use the lacp system-priority command in global configuration mode. To disable port priority, use the no lacp system-priority command.

lacp system-priority priority_value

no lacp system-priority

Syntax Description

priority_value

The priority value.

The range is from 1 to 65535.

Command Modes

Global configuration (config)

Examples

This example shows how to configure the system priority.

Device> enable
Device# configure terminal
Device(config)# lacp system-priority 3

port-control mode primary

To configure the primary mode, use the port-control mode primary command in interface configuration mode. To disable the primary mode, use the no port-control mode command.

port-control mode primary

no port-control mode

Command Modes

Interface configuration (config-if)

Examples

This example shows how to configure the primary mode.

Device> enable
Device# configure terminal
Device(config)# interface ethernet 1/1
Device(config-if-ethernet-1/1)# port-control mode primary

port-control mode secondary

To configure the secondary mode, use the port-control mode secondary command in interface configuration mode. To disable the secondary mode, use the no port-control mode command.

port-control mode secondary

no port-control mode

Command Modes

Interface configuration (config-if)

Examples

This example shows how to configure the secondary mode.

Device> enable
Device# configure terminal
Device(config)# interface ethernet 1/1
Device(config-if-ethernet-1/1)# port-control mode secondary

port-isolation

To configure port isolation, use the port-isolation command in global configuration mode. To disable port isolation, use the no port-isolation command.

port-isolation ethernet slot-number/port-number

no port-isolation ethernet slot-number/port-number

Syntax Description

slot-number/port-number

The port ID.

  • slot-number :

    • GPON: The value is 0.

    • GE Ethernet: The value is 1.

    • 10GE Ethernet: The value is 2.

  • port-number :

    • GPON: The range is from 1 to 8.

    • GE Ethernet: The range is from 1 to 4.

    • 10GE Ethernet: The range is from 1 to 2.

Command Modes

Global configuration (config)

Examples

This example shows how to configure port isolation.

Device> enable
Device# configure terminal
Device(config)# port-isolation ethernet 1/1
Add port isolation downlink port successfully.

Related Commands

Command

Description

show port-isolation

Displays the isolation port

port-rate-statistics interval

To configure port interface statistic interval, use the port-rate-statistics interval value command in global configuration mode. To restore the default value, use the no form of this command.

port-rate-statistics interval value

no port-rate-statistics interval

Syntax Description

value

The time interval range.

The range is from 1 to 5. The unit is minutes. The default is 5.

Command Modes

Global configuration (config)

Examples

This example shows how to configure port interface statistic interval.

Device> enable
Device# configure terminal
Device(config)# port-rate-statistics interval 3
Port rate statistics interval has been changed, and will 
restart calculating port average rate!

psg group-id force-switch

To force a port changeover, use the psg group-id force-switch command in global configuration mode

psg group-id force-switch

Syntax Description

group-id

The protection switch group ID.

The range is 0 to 7.

Command Modes

Global configuration (config)

Examples

This example shows how to force a switch changeover. 

Device> enable
Device# configure terminal
Device(config)# psg 1 type-b primary interface gpon 0/3 secondary interface gpon 0/1
Config success.
Device(config)# psg 1 force-switch
Switch success.

psg group-id type-b

To configure a protection switch group, use the psg group-id type-b primary interface gpon slot-number/port-number secondary interface gpon slot-number/port-number command in global configuration mode. To remove the protection switch group, use the no psg group-id command.

psg group-id type-b primary interface gpon slot-number/port-number secondary interface gpon slot-number/port-number no psg group-id

Syntax Description

group-id

The protection switch group ID.

The range is from 0 to 7.
slot-number/port-number

  • slot-number : The GPON slot number. The value is 0.

  • port-number : The GPON port number. The range is from 1 to 8.

Command Modes

Global configuration (config)

Examples

This example shows how to configure a protection switch group. 

Device> enable
Device# configure terminal
Device(config)# psg 1 type-b primary interface gpon 0/3 secondary interface gpon 0/1
Config success.

show description

To display the interface description, use the show description command in privileged EXEC or global configuration mode.

show description interface ethernet slot-number/port-number

Syntax Description

slot-number/port-number

The port ID.

  • slot-number :

    • GPON: The value is 0.

    • GE Ethernet: The value is 1.

    • 10GE Ethernet: The value is 2.

  • port-number :

    • GPON: The range is from 1 to 8.

    • GE Ethernet: The range is from 1 to 4.

    • 10GE Ethernet: The range is from 1 to 2.

Command Modes

Privileged EXEC (#)

Global configuration (config)

Examples

This example shows how to view the interface description.

Device> enable
Device# configure terminal
Device(config)# show description interface ethernet 1/1
Port     description
e1/1     text
Total entries: 1.

show interface sfp

To display information about SFP parameters, use the show interface sfp command in privileged EXEC or global configuration mode.

show interface sfp {ethernet | gpon }slot-number/port-number

Syntax Description

slot-number/port-number

The port ID.

  • slot-number :

    • GPON: The value is 0.

    • GE Ethernet: The value is 1.

    • 10GE Ethernet: The value is 2.

  • port-number :

    • GPON: The range is from 1 to 8.

    • GE Ethernet: The range is from 1 to 4.

    • 10GE Ethernet: The range is from 1 to 2.

Command Modes

Privileged EXEC (#)

Global configuration (config)

Examples

This example shows how to view the information about SFP parameters

Device> enable
Device# configure terminal
Device(config)# show interface sfp ethernet 1/1

show lacp internal

To display information of the aggregation group, use the show lacp internal command in privileged EXEC or global configuration mode.

show lacp internal [channel_group_id]

Syntax Description

channel_group_id

The channel group ID.

The range is from 0 to 5.

Command Modes

Privileged EXEC (#)

Global configuration (config)

Examples

This example shows how to view information about the aggregation group.

Device> enable
Device# configure terminal
Device(config)# show lacp internal
Load balance: dst-ip

Channel: 2, static channel
Port   State   A-Key  O-Key  Priority   Logic-port   Actor-state
e1/1   down    -      -      -          9            -

Channel: 4, dynamic channel
Port   State   A-Key  O-Key  Priority   Logic-port   Actor-state

actor-state: activity/timeout/aggregation/synchronization
             collecting/distributing/defaulted/expired

show lacp neighbor

To display the neighbor information of the aggregation group, use the show lacp neighbor command in privileged EXEC or global configuration mode.

show lacp neighbor [channel_group_id]

Syntax Description

channel_group_id

The channel group ID.

The range is from 0 to 5.

Command Modes

Privileged EXEC (#)

Global configuration (config)

Examples

This example shows how to view the neighbor information of the aggregation group

Device> enable
Device# configure terminal
Device(config)# show lacp neighbor

Channel: 4
Local  Port   Key   Pri    ID          Timeout    Nei-state

nei-state: activity/timeout/aggregation/synchronization
           collecting/distributing/defaulted/expired

show lacp sys-id

To display the system priority configuration, use the show lacp sys-id command in privileged EXEC or global configuration mode.

show lacp sys-id

Command Modes

Privileged EXEC (#)

Global configuration (config)

Examples

This example shows how to view the system priority configuration.

Device> enable
Device# configure terminal
Device(config)# show lacp sys-id

3,000a5a9b1815

show port-control mode

To display the configured port-control mode, use the show port-control mode command in privileged EXEC or global configuration mode.

show port-control mode

Command Modes

Privileged EXEC (#)

Global configuration (config)

Examples

This example shows how to view the configured port-control mode.

Device> enable
Device# configure terminal
Device(config)# show port-control mode
port   negotiate-flag  port-control-mode
e1/1   enable          auto
e1/2   enable          auto
e1/3   enable          auto
e1/4   enable          auto

show port-isolation

To display the isolation port, use the show port-isolation command in privileged EXEC or global configuration mode.

show port-isolation

Command Modes

Privileged EXEC (#)

Global configuration (config)

Examples

This example shows how to view isolation port configuration.

Device> enable
Device# configure terminal
Device(config)# show port-isolation
Port isolation downlink port :
e1/2-e1/4.

Related Commands

Command

Description

port-isolation

Configures port isolation

show psg

To display the protection switch group configurations, use the show psg group-id command in privileged EXEC or global configuration mode.

show psg { group-id | all }

Syntax Description

group-id

The protection switch group ID.

The range is from 0 to 7.
all

All protection switch groups

Command Modes

Privileged EXEC (#)

Global configuration (config)

Examples

This example shows how to configure a protection switch group. 

Device> enable
Device# configure terminal
Device(config)# show psg 0
GroupID   Member  Role      State
0         0/1     PRIMARY   WORKING
          0/2     SECONDARY STANDBY
Total: 1.

show statistics interface ethernet

To display the port rate statistics information, use the show statistics interface command in privileged EXEC or global configuration mode.

show statistics interface ethernet slot-number/port-number

Syntax Description

slot-number/port-number

The port ID.

  • slot-number :

    • GPON: The value is 0.

    • GE Ethernet: The value is 1.

    • 10GE Ethernet: The value is 2.

  • port-number :

    • GPON: The range is from 1 to 8.

    • GE Ethernet: The range is from 1 to 4.

    • 10GE Ethernet: The range is from 1 to 2.

Command Modes

Privileged EXEC (#)

Global configuration (config)

Examples

This example shows how to view the port rate statistics information.

evice> enable
Device# configure terminal
Device(config)# show statistics interface ethernet 1/3
Port number  :  e1/3
last 5 minutes input rate 24784 bits/sec, 37 packets/sec
last 5 minutes output rate 1120 bits/sec, 1 packets/sec
64 byte packets:455394067
65-127 byte packets:302514090
128-255 byte packets:17535520
256-511 byte packets:20599116
512-1023 byte packets:4737262
1024-1518 byte packets:475868
788888610 packets input, 69778227468 bytes , 312945536 discarded packets
18800297 unicasts, 270957185 multicasts, 499131128 broadcasts
0 input errors, 0 FCS error, 0 symbol error, 0 false carrier
0 runts, 0 giants
12367313 packets output, 1245119790 bytes, 256 discarded packets
8303627 unicasts, 3620977 multicasts, 442709 broadcasts
0 output errors, 0 deferred, 0 collisions
0 late collisions
Total entries: 1.

show statistics

To display port rate statistics information, use the show statistics interface ethernet command in privileged EXEC or global configuration mode.

show statistics interface ethernet slot-number/port-number

Syntax Description

slot-number/port-number

The port ID.

  • slot-number :

    • GPON: The value is 0.

    • GE Ethernet: The value is 1.

    • 10GE Ethernet: The value is 2.

  • port-number :

    • GPON: The range is from 1 to 8.

    • GE Ethernet: The range is from 1 to 4.

    • 10GE Ethernet: The range is from 1 to 2.

Command Modes

Privileged EXEC (#)

Global configuration (config)

Examples

This example show how to view the port rate statistics information.

Device> enable
Device# configure terminal
Device(config)# show statistics interface ethernet 1/1
Port number  :  e1/1
last 5 minutes input rate 0 bits/sec, 0 packets/sec
last 5 minutes output rate 0 bits/sec, 0 packets/sec
64 byte packets:0
65-127 byte packets:0
128-255 byte packets:0
256-511 byte packets:0
512-1023 byte packets:0
1024-1518 byte packets:0
0 packets input, 0 bytes , 0 discarded packets
0 unicasts, 0 multicasts, 0 broadcasts
0 input errors, 0 FCS error, 0 symbol error, 0 false carrier
0 runts, 0 giants
0 packets output, 0 bytes, 0 discarded packets
0 unicasts, 0 multicasts, 0 broadcasts
0 output errors, 0 deferred, 0 collisions
0 late collisions
Total entries: 1.

show statistics channel-group

To display LACP statistical information, use the show statistics channel-group command in privileged EXEC or global configuration mode.

show statistics channel-group [channel_group_id]

Syntax Description

channel_group_id

The channel group ID.

The range is from 0 to 5.

Command Modes

Privileged EXEC (#)

Global configuration (config)

Examples

This example shows how to view the LACP statistical information

Device> enable
Device# configure terminal
Device(config)# show statistics channel-group
Channel group : 2
last 5 minutes input rate 0 bits/sec, 0 packets/sec
last 5 minutes output rate 0 bits/sec, 0 packets/sec
64 byte packets:0
65-127 byte packets:0
128-255 byte packets:0
256-511 byte packets:0
512-1023 byte packets:0
1024-1518 byte packets:0
0 packets input, 0 bytes , 0 discarded packets
0 unicasts, 0 multicasts, 0 broadcasts
0 input errors, 0 FCS error, 0 symbol error, 0 false carrier
0 runts, 0 giants
0 packets output, 0 bytes, 0 discarded packets
0 unicasts, 0 multicasts, 0 broadcasts
0 output errors, 0 deferred, 0 collisions
0 late collisions

Channel group : 4

This channel group does not include any ports!


Total entries: 2.

show statistics dynamic interface

To display the real-time statistic information of an interface, use the show statistics dynamic interface command in privileged EXEC or global configuration mode.

show statistics dynamic interface

Command Modes

Privileged EXEC (#)

Global configuration (config)

Examples

This example shows how to view the real-time statistic information of an interface.

Device> enable
Device# configure terminal
Device(config)# show statistics dynamic interface
Port Statistics        Sun Dec 9 17:40:29 2001
port  link   Tx Pkt    Tx Byte     Rx Pkt    Rx Byte     Rx        Rx
      Status Count     Count       Count     Count       Bcast     Mcast
==============================================================================
g0/1    up   1427776E3 122120178E3 3230173   579417376   279481    171727
g0/2    down 0         0           0         0           0         0
g0/3    down 0         0           0         0           0         0
g0/4    down 0         0           0         0           0         0
g0/5    down 0         0           0         0           0         0
g0/6    down 0         0           0         0           0         0
g0/7    down 0         0           0         0           0         0
g0/8    down 0         0           0         0           0         0
e1/1    down 0         0           0         0           0         0
e1/2    down 0         0           0         0           0         0
e1/3    up   12366419  1245034896  788871832 69776674248 499122592 270949818
e1/4    down 2         210         4         256         0         4
e2/1    down 0         0           0         0           0         0
e2/2    down 0         0           0         0           0         0
==============0->Clear Counters U->page up D->page down CR->exit==============

Notes:If you see a E number, you can use the command "line width" to get more
information.

show utilization interface

To display the interface utilization, use the show utilization interface command in privileged EXEC or global configuration mode.

show utilization interface

Command Modes

Privileged EXEC (#)

Global configuration (config)

Examples

This example shows how to view the interface utilization.

Device> enable
Device# configure terminal
Device(config)# show utilization interface
Link Utilization Averages           Tue Dec 4 19:06:53 2001
port  link    Receive   Peak Rx   Transmit  Peak Tx
      Status  pkts/sec  pkts/sec  pkts/sec  pkts/sec
==================================================================
g0/1  up      0         0         16        16
g0/2  down    0         0         0         0
g0/3  down    0         0         0         0
g0/4  down    0         0         0         0
g0/5  down    0         0         0         0
g0/6  down    0         0         0         0
g0/7  down    0         0         0         0
g0/8  down    0         0         0         0
e1/1  down    0         0         0         0
e1/2  down    0         0         0         0
e1/3  up      37        37        2         2
e1/4  down    0         0         0         0
e2/1  down    0         0         0         0
e2/2  down    0         0         0         0
=====spacebar->toggle screen U->page up D->page down CR->exit=====

speed

To configure the interface speed, use the speed command in interface configuration mode. To disable the interface speed, use the no speed command.

speed {1000 | 10000 | auto}

no speed

Syntax Description

1000

Port speed is 1000Mbps
10000

Port speed is 10000Mbps
auto

Port speed is automatic

Command Modes

Interface configuration (config-if)

Examples

This example shows how to configure the interface speed

Device> enable
Device# configure terminal
Device(config)# interface ethernet 1/1
Device(config-if-ethernet-1/1)# speed 1000