Consolidated Platform Configuration Guide, Cisco IOS XE 3.6E (Catalyst 3650 Switches)

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Book Contents
Find Matches in This Book

Results

Updated:
July 3, 2014

Chapter: Configuring Internal Power Supplies

Configuring Internal Power Supplies

Information About Internal Power Supplies

See the switch installation guide for information about the power supplies.

How to Configure Internal Power Supplies

Configuring Internal Power Supply

You can use the power supply EXEC command to configure and manage the internal power supply on the switch. The switch does not support the no power supply EXEC command.

Follow these steps beginning in user EXEC mode:

SUMMARY STEPS

  1. power supply switch_number slot {A | B } { off | on }
  2. show environment power

DETAILED STEPS

  Command or Action Purpose
Step 1

power supply switch_number slot {A | B } { off | on }

Example:


Switch# power supply 1 slot A on

Sets the specified power supply to off or on by using one of these keywords:

  • A —Selects the power supply in slot A.

  • B —Selects power supply in slot B.

    Note 

    Power supply slot B is the closest to the outer edge of the switch.

  • off —Set the power supply off.

  • on —Set the power supply on.

By default, the switch power supply is on.

Step 2

show environment power

Example:


Switch# show environment power

Verifies your settings.

Monitoring Internal Power Supplies

Table 1. Show Commands for Power Supplies

Command

Purpose

show environment power [ all | switch switch_number ]

(Optional) Displays the status of the internal power supplies for each switch in the stack or for the specified switch. The range is 1 to 9, depending on the switch member numbers in the stack.

The switch keywords are available only on stacking-capable switches.

Configuration Examples for Internal Power Supplies

This example shows how to set the power supply in slot A to off:


Switch# power supply 1 slot A off
Disabling Power supply A may result in a power loss to PoE devices and/or switches ... Continue? (yes/[no]): yes 
Switch#
Jun 10 04:52:54.389: %PLATFORM_ENV-6-FRU_PS_OIR: FRU Power Supply 1 powered off 
Jun 10 04:52:56.717: %PLATFORM_ENV-1-FAN_NOT_PRESENT: Fan is not present
Switch#

This example shows how to set the power supply in slot A to on:


Switch# power supply 1 slot A on
Jun 10 04:54:39.600: %PLATFORM_ENV-6-FRU_PS_OIR: FRU Power Supply 1 powered on

This example shows the output of the show env power command: 


Switch# show env power

SW  PID                 Serial#     Status           Sys Pwr  PoE Pwr  Watts
--- ------------------  ----------  ---------------  -------  -------  -----
1A  PWR-C2-640WAC       DCB1705B05B OK               Good     Good     640
1B  Not Present

Switch#
Table 2. show env power Status Descriptions
Field Description

OK

The power supply is present and power is good.

Not Present

No power supply is installed.

No Input Power

The power supply is present but there is no input power.

Disabled

The power supply and input power are present, but power supply is switched off by CLI.

Not Responding

The power supply is not recognizable or is faulty.

Failure-Fan

The power supply fan is faulty.

Additional References

Error Message Decoder

Description Link

To help you research and resolve system error messages in this release, use the Error Message Decoder tool.

https://www.cisco.com/cgi-bin/Support/Errordecoder/index.cgi

MIBs

MIB MIBs Link

All supported MIBs for this release.

To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs

Technical Assistance

Description Link

The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

http://www.cisco.com/support

Feature History and Information for Internal Power Supplies

Release

Modification

Cisco IOS XE 3.2SECisco IOS XE 3.2SECisco IOS XE 3.3SE

This feature was introduced.

Was this Document Helpful?

FeedbackFeedback

Contact Cisco