Consolidated Platform Configuration Guide, Cisco IOS Release 15.2(5)E (Catalyst 3560-CX and 2960-CX Switches)

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Restrictions for STP

An attempt to configure a device as the root device fails if the value necessary to be the root device is less than 1.
If your network consists of devices that support and do not support the extended system ID, it is unlikely that the device with the extended system ID support will become the root device. The extended system ID increases the device priority value every time the VLAN number is greater than the priority of the connected devices running older software.
The root device for each spanning-tree instance should be a backbone or distribution device. Do not configure an access device as the spanning-tree primary root.

Spanning Tree Protocol

Spanning Tree Protocol (STP) is a Layer 2 link management protocol that provides path redundancy while preventing loops in the network. For a Layer 2 Ethernet network to function properly, only one active path can exist between any two stations. Multiple active paths among end stations cause loops in the network. If a loop exists in the network, end stations might receive duplicate messages. Devices might also learn end-station MAC addresses on multiple Layer 2 interfaces. These conditions result in an unstable network. Spanning-tree operation is transparent to end stations, which cannot detect whether they are connected to a single LAN segment or a switched LAN of multiple segments.

The STP uses a spanning-tree algorithm to select one device of a redundantly connected network as the root of the spanning tree. The algorithm calculates the best loop-free path through a switched Layer 2 network by assigning a role to each port based on the role of the port in the active topology:

Root—A forwarding port elected for the spanning-tree topology
Designated—A forwarding port elected for every switched LAN segment
Alternate—A blocked port providing an alternate path to the root bridge in the spanning tree
Backup—A blocked port in a loopback configuration

The device that has all of its ports as the designated role or as the backup role is the root device. The device that has at least one of its ports in the designated role is called the designated device.

Spanning tree forces redundant data paths into a standby (blocked) state. If a network segment in the spanning tree fails and a redundant path exists, the spanning-tree algorithm recalculates the spanning-tree topology and activates the standby path. Devices send and receive spanning-tree frames, called bridge protocol data units (BPDUs), at regular intervals. The devices do not forward these frames but use them to construct a loop-free path. BPDUs contain information about the sending device and its ports, including device and MAC addresses, device priority, port priority, and path cost. Spanning tree uses this information to elect the root device and root port for the switched network and the root port and designated port for each switched segment.

When two ports on a device are part of a loop, the spanning-tree and path cost settings control which port is put in the forwarding state and which is put in the blocking state. The spanning-tree port priority value represents the location of a port in the network topology and how well it is located to pass traffic. The path cost value represents the media speed.

Note

By default, the device sends keepalive messages (to ensure the connection is up) only on interfaces that do not have small form-factor pluggable (SFP) modules. You can change the default for an interface by entering the [no] keepalive interface configuration command with no keywords.

Spanning-Tree Topology and BPDUs

The stable, active spanning-tree topology of a switched network is controlled by these elements:

The unique bridge ID (device priority and MAC address) associated with each VLAN on each device.
The spanning-tree path cost to the root device.
The port identifier (port priority and MAC address) associated with each Layer 2 interface.

When the devices in a network are powered up, each functions as the root device. Each device sends a configuration BPDU through all of its ports. The BPDUs communicate and compute the spanning-tree topology. Each configuration BPDU contains this information:

The unique bridge ID of the device that the sending device identifies as the root device
The spanning-tree path cost to the root
The bridge ID of the sending device
Message age
The identifier of the sending interface
Values for the hello, forward delay, and max-age protocol timers

When a device receives a configuration BPDU that contains superior information (lower bridge ID, lower path cost, and so forth), it stores the information for that port. If this BPDU is received on the root port of the device, the device also forwards it with an updated message to all attached LANs for which it is the designated device.

If a device receives a configuration BPDU that contains inferior information to that currently stored for that port, it discards the BPDU. If the device is a designated device for the LAN from which the inferior BPDU was received, it sends that LAN a BPDU containing the up-to-date information stored for that port. In this way, inferior information is discarded, and superior information is propagated on the network.

A BPDU exchange results in these actions:

One device in the network is elected as the root device (the logical center of the spanning-tree topology in a switched network). See the figure following the bullets.

For each VLAN, the device with the highest device priority (the lowest numerical priority value) is elected as the root device. If all devices are configured with the default priority (32768), the device with the lowest MAC address in the VLAN becomes the root device. The device priority value occupies the most significant bits of the bridge ID, .
A root port is selected for each device (except the root device). This port provides the best path (lowest cost) when the device forwards packets to the root device.
The shortest distance to the root device is calculated for each device based on the path cost.
A designated device for each LAN segment is selected. The designated device incurs the lowest path cost when forwarding packets from that LAN to the root device. The port through which the designated device is attached to the LAN is called the designated port.

Note

If the logging event spanning tree command is configured on multiple interfaces and the topology changes, it may result in several logging messages and high CPU utilization. This may cause the switch to drop or delay the processing of STP BPDUs.

To prevent this behavior, remove the logging event spanning tree and logging event status commands or disable logging to the console.

All paths that are not needed to reach the root device from anywhere in the switched network are placed in the spanning-tree blocking mode.

Bridge ID, Device Priority, and Extended System ID

The IEEE 802.1D standard requires that each device has an unique bridge identifier (bridge ID), which controls the selection of the root device. Because each VLAN is considered as a different logical bridge with PVST+ and Rapid PVST+, the same device must have a different bridge ID for each configured VLAN. Each VLAN on the device has a unique 8-byte bridge ID. The 2 most-significant bytes are used for the device priority, and the remaining 6 bytes are derived from the device MAC address.

The device supports the IEEE 802.1t spanning-tree extensions, and some of the bits previously used for the device priority are now used as the VLAN identifier. The result is that fewer MAC addresses are reserved for the device, and a larger range of VLAN IDs can be supported, all while maintaining the uniqueness of the bridge ID.

The 2 bytes previously used for the device priority are reallocated into a 4-bit priority value and a 12-bit extended system ID value equal to the VLAN ID.

Table 1. Device Priority Value and Extended System ID
Priority Value				Extended System ID (Set Equal to the VLAN ID)
Bit 16	Bit 15	Bit 14	Bit 13	Bit 12	Bit 11	Bit 10	Bit 9	Bit 8	Bit 7	Bit 6	Bit 5	Bit 4	Bit 3	Bit 2	Bit 1
32768	16384	8192	4096	2048	1024	512	256	128	64	32	16	8	4	2	1

Spanning tree uses the extended system ID, the device priority, and the allocated spanning-tree MAC address to make the bridge ID unique for each VLAN.

Support for the extended system ID affects how you manually configure the root device, the secondary root device, and the device priority of a VLAN. For example, when you change the device priority value, you change the probability that the device will be elected as the root device. Configuring a higher value decreases the probability; a lower value increases the probability.

If any root device for the specified VLAN has a device priority lower than 24576, the device sets its own priority for the specified VLAN to 4096 less than the lowest device priority. 4096 is the value of the least-significant bit of a 4-bit device priority value as shown in the table.

Port Priority Versus Path Cost

If a loop occurs, spanning tree uses port priority when selecting an interface to put into the forwarding state. You can assign higher priority values (lower numerical values) to interfaces that you want selected first and lower priority values (higher numerical values) that you want selected last. If all interfaces have the same priority value, spanning tree puts the interface with the lowest interface number in the forwarding state and blocks the other interfaces.

The spanning-tree path cost default value is derived from the media speed of an interface. If a loop occurs, spanning tree uses cost when selecting an interface to put in the forwarding state. You can assign lower cost values to interfaces that you want selected first and higher cost values that you want selected last. If all interfaces have the same cost value, spanning tree puts the interface with the lowest interface number in the forwarding state and blocks the other interfaces.

If your device is a member of a device stack, you must assign lower cost values to interfaces that you want selected first and higher cost values that you want selected last instead of adjusting its port priority. For details, see Related Topics.

Spanning-Tree Interface States

Propagation delays can occur when protocol information passes through a switched LAN. As a result, topology changes can take place at different times and at different places in a switched network. When an interface transitions directly from nonparticipation in the spanning-tree topology to the forwarding state, it can create temporary data loops. Interfaces must wait for new topology information to propagate through the switched LAN before starting to forward frames. They must allow the frame lifetime to expire for forwarded frames that have used the old topology.

Each Layer 2 interface on a device using spanning tree exists in one of these states:

Blocking—The interface does not participate in frame forwarding.
Listening—The first transitional state after the blocking state when the spanning tree decides that the interface should participate in frame forwarding.
Learning—The interface prepares to participate in frame forwarding.
Forwarding—The interface forwards frames.
Disabled—The interface is not participating in spanning tree because of a shutdown port, no link on the port, or no spanning-tree instance running on the port.

An interface moves through these states:

From initialization to blocking
From blocking to listening or to disabled
From listening to learning or to disabled
From learning to forwarding or to disabled
From forwarding to disabled

Figure 1. Spanning-Tree Interface States. An interface moves through the states.

When you power up the device, spanning tree is enabled by default, and every interface in the device, VLAN, or network goes through the blocking state and the transitory states of listening and learning. Spanning tree stabilizes each interface at the forwarding or blocking state.

When the spanning-tree algorithm places a Layer 2 interface in the forwarding state, this process occurs:

The interface is in the listening state while spanning tree waits for protocol information to move the interface to the blocking state.
While spanning tree waits for the forward-delay timer to expire, it moves the interface to the learning state and resets the forward-delay timer.
In the learning state, the interface continues to block frame forwarding as the device learns end-station location information for the forwarding database.
When the forward-delay timer expires, spanning tree moves the interface to the forwarding state, where both learning and frame forwarding are enabled.

Blocking State

A Layer 2 interface in the blocking state does not participate in frame forwarding. After initialization, a BPDU is sent to each device interface. A device initially functions as the root until it exchanges BPDUs with other devices. This exchange establishes which device in the network is the root or root device. If there is only one device in the network, no exchange occurs, the forward-delay timer expires, and the interface moves to the listening state. An interface always enters the blocking state after device initialization.

An interface in the blocking state performs these functions:

Discards frames received on the interface
Discards frames switched from another interface for forwarding
Does not learn addresses
Receives BPDUs

Listening State

The listening state is the first state a Layer 2 interface enters after the blocking state. The interface enters this state when the spanning tree decides that the interface should participate in frame forwarding.

An interface in the listening state performs these functions:

Discards frames received on the interface
Discards frames switched from another interface for forwarding
Does not learn addresses
Receives BPDUs

Learning State

A Layer 2 interface in the learning state prepares to participate in frame forwarding. The interface enters the learning state from the listening state.

An interface in the learning state performs these functions:

Discards frames received on the interface
Discards frames switched from another interface for forwarding
Learns addresses
Receives BPDUs

Forwarding State

A Layer 2 interface in the forwarding state forwards frames. The interface enters the forwarding state from the learning state.

An interface in the forwarding state performs these functions:

Receives and forwards frames received on the interface
Forwards frames switched from another interface
Learns addresses
Receives BPDUs

Disabled State

A Layer 2 interface in the disabled state does not participate in frame forwarding or in the spanning tree. An interface in the disabled state is nonoperational.

A disabled interface performs these functions:

Discards frames received on the interface
Discards frames switched from another interface for forwarding
Does not learn addresses
Does not receive BPDUs

How a Device or Port Becomes the Root Device or Root Port

If all devices in a network are enabled with default spanning-tree settings, the device with the lowest MAC address becomes the root device.

Figure 2. Spanning-Tree Topology. Device A is elected as the root device because the device priority of all the devices is set to the default (32768) and Device A has the lowest MAC address. However, because of traffic patterns, number of forwarding interfaces, or link types, Device A might not be the ideal root device. By increasing the priority (lowering the numerical value) of the ideal device so that it becomes the root device, you force a spanning-tree recalculation to form a new topology with the ideal device as the root.

When the spanning-tree topology is calculated based on default parameters, the path between source and destination end stations in a switched network might not be ideal. For instance, connecting higher-speed links to an interface that has a higher number than the root port can cause a root-port change. The goal is to make the fastest link the root port.

For example, assume that one port on Device B is a Gigabit Ethernet link and that another port on Device B (a 10/100 link) is the root port. Network traffic might be more efficient over the Gigabit Ethernet link. By changing the spanning-tree port priority on the Gigabit Ethernet port to a higher priority (lower numerical value) than the root port, the Gigabit Ethernet port becomes the new root port.

Spanning Tree and Redundant Connectivity

You can also create redundant links between devices by using EtherChannel groups.

Spanning-Tree Address Management

IEEE 802.1D specifies 17 multicast addresses, ranging from 0x00180C2000000 to 0x0180C2000010, to be used by different bridge protocols. These addresses are static addresses that cannot be removed.

Regardless of the spanning-tree state, each device in the stack receives but does not forward packets destined for addresses between 0x0180C2000000 and 0x0180C200000F.

If spanning tree is enabled, the CPU on the device or on each device in the stack receives packets destined for 0x0180C2000000 and 0x0180C2000010. If spanning tree is disabled, the device or each device in the stack forwards those packets as unknown multicast addresses.

Accelerated Aging to Retain Connectivity

The default for aging dynamic addresses is 5 minutes, the default setting of the mac address-table aging-time global configuration command. However, a spanning-tree reconfiguration can cause many station locations to change. Because these stations could be unreachable for 5 minutes or more during a reconfiguration, the address-aging time is accelerated so that station addresses can be dropped from the address table and then relearned. The accelerated aging is the same as the forward-delay parameter value (spanning-tree vlan vlan-id forward-time seconds global configuration command) when the spanning tree reconfigures.

Because each VLAN is a separate spanning-tree instance, the device accelerates aging on a per-VLAN basis. A spanning-tree reconfiguration on one VLAN can cause the dynamic addresses learned on that VLAN to be subject to accelerated aging. Dynamic addresses on other VLANs can be unaffected and remain subject to the aging interval entered for the device.

Spanning-Tree Modes and Protocols

The device supports these spanning-tree modes and protocols:

PVST+—This spanning-tree mode is based on the IEEE 802.1D standard and Cisco proprietary extensions. The PVST+ runs on each VLAN on the device up to the maximum supported, ensuring that each has a loop-free path through the network.

The PVST+ provides Layer 2 load-balancing for the VLAN on which it runs. You can create different logical topologies by using the VLANs on your network to ensure that all of your links are used but that no one link is oversubscribed. Each instance of PVST+ on a VLAN has a single root device. This root device propagates the spanning-tree information associated with that VLAN to all other devices in the network. Because each device has the same information about the network, this process ensures that the network topology is maintained.
Rapid PVST+—This spanning-tree mode is the same as PVST+ except that is uses a rapid convergence based on the IEEE 802.1w standard. Beginning from 15.2(4)E release, the STP default mode is Rapid PVST+ . To provide rapid convergence, the Rapid PVST+ immediately deletes dynamically learned MAC address entries on a per-port basis upon receiving a topology change. By contrast, PVST+ uses a short aging time for dynamically learned MAC address entries.

Rapid PVST+ uses the same configuration as PVST+ (except where noted), and the device needs only minimal extra configuration. The benefit of Rapid PVST+ is that you can migrate a large PVST+ install base to Rapid PVST+ without having to learn the complexities of the Multiple Spanning Tree Protocol (MSTP) configuration and without having to reprovision your network. In Rapid PVST+ mode, each VLAN runs its own spanning-tree instance up to the maximum supported.
MSTP—This spanning-tree mode is based on the IEEE 802.1s standard. You can map multiple VLANs to the same spanning-tree instance, which reduces the number of spanning-tree instances required to support a large number of VLANs. The MSTP runs on top of the RSTP (based on IEEE 802.1w), which provides for rapid convergence of the spanning tree by eliminating the forward delay and by quickly transitioning root ports and designated ports to the forwarding state. In a device stack, the cross-stack rapid transition (CSRT) feature performs the same function as RSTP. You cannot run MSTP without RSTP or CSRT.

Supported Spanning-Tree Instances

In PVST+ or Rapid PVST+ mode, the device or device stack supports up to 128 spanning-tree instances.

In MSTP mode, the device or device stack supports up to 65 MST instances. The number of VLANs that can be mapped to a particular MST instance is unlimited.

Spanning-Tree Interoperability and Backward Compatibility

In a mixed MSTP and PVST+ network, the common spanning-tree (CST) root must be inside the MST backbone, and a PVST+ device cannot connect to multiple MST regions.

When a network contains devices running Rapid PVST+ and devices running PVST+, we recommend that the Rapid PVST+ devices and PVST+ devices be configured for different spanning-tree instances. In the Rapid PVST+ spanning-tree instances, the root device must be a Rapid PVST+ device. In the PVST+ instances, the root device must be a PVST+ device. The PVST+ devices should be at the edge of the network.

All stack members run the same version of spanning tree (all PVST+, all Rapid PVST+, or all MSTP).

Table 2. PVST+, MSTP, and Rapid-PVST+ Interoperability and Compatibility
	PVST+	MSTP	Rapid PVST+
PVST+	Yes	Yes (with restrictions)	Yes (reverts to PVST+)
MSTP	Yes (with restrictions)	Yes	Yes (reverts to PVST+)
Rapid PVST+	Yes (reverts to PVST+)	Yes (reverts to PVST+)	Yes

STP and IEEE 802.1Q Trunks

The IEEE 802.1Q standard for VLAN trunks imposes some limitations on the spanning-tree strategy for a network. The standard requires only one spanning-tree instance for all VLANs allowed on the trunks. However, in a network of Cisco devices connected through IEEE 802.1Q trunks, the devices maintain one spanning-tree instance for each VLAN allowed on the trunks.

When you connect a Cisco device to a non-Cisco device through an IEEE 802.1Q trunk, the Cisco device uses PVST+ to provide spanning-tree interoperability. If Rapid PVST+ is enabled, the device uses it instead of PVST+. The device combines the spanning-tree instance of the IEEE 802.1Q VLAN of the trunk with the spanning-tree instance of the non-Cisco IEEE 802.1Q device.

However, all PVST+ or Rapid PVST+ information is maintained by Cisco devices separated by a cloud of non-Cisco IEEE 802.1Q devices. The non-Cisco IEEE 802.1Q cloud separating the Cisco devices is treated as a single trunk link between the devices.

Rapid PVST+ is automatically enabled on IEEE 802.1Q trunks, and no user configuration is required. The external spanning-tree behavior on access ports and Inter-Switch Link (ISL) trunk ports is not affected by PVST+.

VLAN-Bridge Spanning Tree

Cisco VLAN-bridge spanning tree is used with the fallback bridging feature (bridge groups), which forwards non-IP protocols such as DECnet between two or more VLAN bridge domains or routed ports. The VLAN-bridge spanning tree allows the bridge groups to form a spanning tree on top of the individual VLAN spanning trees to prevent loops from forming if there are multiple connections among VLANs. It also prevents the individual spanning trees from the VLANs being bridged from collapsing into a single spanning tree.

To support VLAN-bridge spanning tree, some of the spanning-tree timers are increased. To use the fallback bridging feature, you must have the IP services feature set enabled on your device.

Default Spanning-Tree Configuration

Table 3. Default Spanning-Tree Configuration
Feature	Default Setting
Enable state	Enabled on VLAN 1.
Spanning-tree mode	Rapid PVST+ ( PVST+ and MSTP are disabled.)
Device priority	32768
Spanning-tree port priority (configurable on a per-interface basis)	128
Spanning-tree port cost (configurable on a per-interface basis)	1000 Mb/s: 4 100 Mb/s: 19 10 Mb/s: 100
Spanning-tree VLAN port priority (configurable on a per-VLAN basis)	128
Spanning-tree VLAN port cost (configurable on a per-VLAN basis)	1000 Mb/s: 4 100 Mb/s: 19 10 Mb/s: 100
Spanning-tree timers	Hello time: 2 seconds Forward-delay time: 15 seconds Maximum-aging time: 20 seconds Transmit hold count: 6 BPDUs

Note

Beginning in Cisco IOS Release 15.2(4)E, the default STP mode is Rapid PVST+.

Changing the Spanning-Tree Mode

The switch supports three spanning-tree modes: per-VLAN spanning tree plus (PVST+), Rapid PVST+, or multiple spanning tree protocol (MSTP). By default, the device runs the Rapid PVST+ protocol.

If you want to enable a mode that is different from the default mode, this procedure is required.

SUMMARY STEPS

enable
configure terminal
spanning-tree mode {pvst | mst | rapid-pvst}
interface interface-id
spanning-tree link-type point-to-point
end
clear spanning-tree detected-protocols

DETAILED STEPS

	Command or Action	Purpose
Step 1	enable Example: `Device> enable`	Enables privileged EXEC mode. Enter your password if prompted.
Step 2	configure terminal Example: `Device# configure terminal`	Enters global configuration mode.
Step 3	spanning-tree mode {pvst \| mst \| rapid-pvst} Example: `Device(config)# spanning-tree mode pvst`	Configures a spanning-tree mode. All stack members run the same version of spanning tree. Select pvst to enable PVST+. Select mst to enable MSTP. Select rapid-pvst to enable rapid PVST+.
Step 4	interface `interface-id` Example: `Device(config)# interface GigabitEthernet1/0/1`	Specifies an interface to configure, and enters interface configuration mode. Valid interfaces include physical ports, VLANs, and port channels. The VLAN ID range is 1 to 4094. The port-channel range is 1 to 48.
Step 5	spanning-tree link-type point-to-point Example: `Device(config-if)# spanning-tree link-type point-to-point`	Specifies that the link type for this port is point-to-point. If you connect this port (local port) to a remote port through a point-to-point link and the local port becomes a designated port, the device negotiates with the remote port and rapidly changes the local port to the forwarding state.
Step 6	end Example: `Device(config-if)# end`	Returns to privileged EXEC mode.
Step 7	clear spanning-tree detected-protocols Example: `Device# clear spanning-tree detected-protocols`	If any port on the device is connected to a port on a legacy IEEE 802.1D device, this command restarts the protocol migration process on the entire device. This step is optional if the designated device detects that this device is running rapid PVST+.

Disabling Spanning Tree

Spanning tree is enabled by default on VLAN 1 and on all newly created VLANs up to the spanning-tree limit. Disable spanning tree only if you are sure there are no loops in the network topology.

Caution

When spanning tree is disabled and loops are present in the topology, excessive traffic and indefinite packet duplication can drastically reduce network performance.

This procedure is optional.

SUMMARY STEPS

enable
configure terminal
no spanning-tree vlan vlan-id
end

DETAILED STEPS

	Command or Action	Purpose
Step 1	enable Example: `Device> enable`	Enables privileged EXEC mode. Enter your password if prompted.
Step 2	configure terminal Example: `Device# configure terminal`	Enters global configuration mode.
Step 3	no spanning-tree vlan `vlan-id` Example: `Device(config)# no spanning-tree vlan 300`	For `vlan-id` , the range is 1 to 4094.
Step 4	end Example: `Device(config)# end`	Returns to privileged EXEC mode.

Configuring the Root Device

To configure a device as the root for the specified VLAN, use the spanning-tree vlan vlan-id root global configuration command to modify the device priority from the default value (32768) to a significantly lower value. When you enter this command, the software checks the device priority of the root devices for each VLAN. Because of the extended system ID support, the device sets its own priority for the specified VLAN to 24576 if this value will cause this device to become the root for the specified VLAN.

Use the diameter keyword to specify the Layer 2 network diameter (that is, the maximum number of device hops between any two end stations in the Layer 2 network). When you specify the network diameter, the device automatically sets an optimal hello time, forward-delay time, and maximum-age time for a network of that diameter, which can significantly reduce the convergence time. You can use the hello keyword to override the automatically calculated hello time.

This procedure is optional.

SUMMARY STEPS

enable
configure terminal
spanning-tree vlan vlan-id root primary [diameter net-diameter
end

DETAILED STEPS

	Command or Action	Purpose
Step 1	enable Example: `Device> enable`	Enables privileged EXEC mode. Enter your password if prompted.
Step 2	configure terminal Example: `Device# configure terminal`	Enters global configuration mode.
Step 3	spanning-tree vlan `vlan-id` root primary [diameter `net-diameter` Example: `Device(config)# spanning-tree vlan 20-24 root primary diameter 4`	Configures a device to become the root for the specified VLAN. For `vlan-id` , you can specify a single VLAN identified by VLAN ID number, a range of VLANs separated by a hyphen, or a series of VLANs separated by a comma. The range is 1 to 4094. (Optional) For diameter `net-diameter` , specify the maximum number of devices between any two end stations. The range is 2 to 7.
Step 4	end Example: `Device(config)# end`	Returns to privileged EXEC mode.

What to do next

After configuring the device as the root device, we recommend that you avoid manually configuring the hello time, forward-delay time, and maximum-age time through the spanning-tree vlan vlan-id hello-time , spanning-tree vlan vlan-id forward-time , and the spanning-tree vlan vlan-id max-age global configuration commands.

Configuring a Secondary Root Device

When you configure a device as the secondary root, the device priority is modified from the default value (32768) to 28672. With this priority, the device is likely to become the root device for the specified VLAN if the primary root device fails. This is assuming that the other network devices use the default device priority of 32768, and therefore, are unlikely to become the root device.

You can execute this command on more than one device to configure multiple backup root devices. Use the same network diameter and hello-time values that you used when you configured the primary root device with the spanning-tree vlan vlan-id root primary global configuration command.

This procedure is optional.

SUMMARY STEPS

enable
configure terminal
spanning-tree vlan vlan-id root secondary [diameter net-diameter
end

DETAILED STEPS

	Command or Action	Purpose
Step 1	enable Example: `Device> enable`	Enables privileged EXEC mode. Enter your password if prompted.
Step 2	configure terminal Example: `Device# configure terminal`	Enters global configuration mode.
Step 3	spanning-tree vlan `vlan-id` root secondary [diameter `net-diameter` Example: `Device(config)# spanning-tree vlan 20-24 root secondary diameter 4`	Configures a device to become the secondary root for the specified VLAN. For `vlan-id` , you can specify a single VLAN identified by VLAN ID number, a range of VLANs separated by a hyphen, or a series of VLANs separated by a comma. The range is 1 to 4094. (Optional) For diameter `net-diameter` , specify the maximum number of devices between any two end stations. The range is 2 to 7. Use the same network diameter value that you used when configuring the primary root device.
Step 4	end Example: `Device(config)# end`	Returns to privileged EXEC mode.

Configuring Port Priority

Note

If your device is a member of a device stack, you must use the spanning-tree [vlan vlan-id] cost cost interface configuration command instead of the spanning-tree [vlan vlan-id] port-priority priority interface configuration command to select an interface to put in the forwarding state. Assign lower cost values to interfaces that you want selected first and higher cost values that you want selected last.

This procedure is optional.

SUMMARY STEPS

enable
configure terminal
interface interface-id
spanning-tree port-priority priority
spanning-tree vlan vlan-id port-priority priority
end

DETAILED STEPS

	Command or Action	Purpose
Step 1	enable Example: `Device> enable`	Enables privileged EXEC mode. Enter your password if prompted.
Step 2	configure terminal Example: `Device# configure terminal`	Enters global configuration mode.
Step 3	interface `interface-id` Example: `Device(config)# interface gigabitethernet 1/0/2`	Specifies an interface to configure, and enters interface configuration mode. Valid interfaces include physical ports and port-channel logical interfaces (port-channel `port-channel-number` ).
Step 4	spanning-tree port-priority `priority` Example: `Device(config-if)# spanning-tree port-priority 0`	Configures the port priority for an interface. For `priority` , the range is 0 to 240, in increments of 16; the default is 128. Valid values are 0, 16, 32, 48, 64, 80, 96, 112, 128, 144, 160, 176, 192, 208, 224, and 240. All other values are rejected. The lower the number, the higher the priority.
Step 5	spanning-tree vlan `vlan-id` port-priority `priority` Example: `Device(config-if)# spanning-tree vlan 20-25 port-priority 0`	Configures the port priority for a VLAN. For `vlan-id` , you can specify a single VLAN identified by VLAN ID number, a range of VLANs separated by a hyphen, or a series of VLANs separated by a comma. The range is 1 to 4094. For `priority` , the range is 0 to 240, in increments of 16; the default is 128. Valid values are 0, 16, 32, 48, 64, 80, 96, 112, 128, 144, 160, 176, 192, 208, 224, and 240. All other values are rejected. The lower the number, the higher the priority.
Step 6	end Example: `Device(config-if)# end`	Returns to privileged EXEC mode.

Configuring Path Cost

This procedure is optional.

SUMMARY STEPS

enable
configure terminal
interface interface-id
spanning-tree cost cost
spanning-tree vlan vlan-id cost cost
end

DETAILED STEPS

	Command or Action	Purpose
Step 1	enable Example: `Device> enable`	Enables privileged EXEC mode. Enter your password if prompted.
Step 2	configure terminal Example: `Device# configure terminal`	Enters global configuration mode.
Step 3	interface `interface-id` Example: `Device(config)# interface gigabitethernet 1/0/1`	Specifies an interface to configure, and enters interface configuration mode. Valid interfaces include physical ports and port-channel logical interfaces (port-channel `port-channel-number` ).
Step 4	spanning-tree cost `cost` Example: `Device(config-if)# spanning-tree cost 250`	Configures the cost for an interface. If a loop occurs, spanning tree uses the path cost when selecting an interface to place into the forwarding state. A lower path cost represents higher-speed transmission. For `cost` , the range is 1 to 200000000; the default value is derived from the media speed of the interface.
Step 5	spanning-tree vlan `vlan-id` cost `cost` Example: `Device(config-if)# spanning-tree vlan 10,12-15,20 cost 300`	Configures the cost for a VLAN. If a loop occurs, spanning tree uses the path cost when selecting an interface to place into the forwarding state. A lower path cost represents higher-speed transmission. For `vlan-id` , you can specify a single VLAN identified by VLAN ID number, a range of VLANs separated by a hyphen, or a series of VLANs separated by a comma. The range is 1 to 4094. For `cost` , the range is 1 to 200000000; the default value is derived from the media speed of the interface.
Step 6	end Example: `Device(config-if)# end`	Returns to privileged EXEC mode.

The show spanning-tree interface interface-id privileged EXEC command displays information only for ports that are in a link-up operative state. Otherwise, you can use the show running-config privileged EXEC command to confirm the configuration.

Configuring the Device Priority of a VLAN

You can configure the device priority and make it more likely that a standalone device or a device in the stack will be chosen as the root device.

Note

Exercise care when using this command. For most situations, we recommend that you use the spanning-tree vlan vlan-id root primary and the spanning-tree vlan vlan-id root secondary global configuration commands to modify the device priority.

This procedure is optional.

SUMMARY STEPS

enable
configure terminal
spanning-tree vlan vlan-id priority priority
end

DETAILED STEPS

	Command or Action	Purpose
Step 1	enable Example: `Device> enable`	Enables privileged EXEC mode. Enter your password if prompted.
Step 2	configure terminal Example: `Device# configure terminal`	Enters global configuration mode.
Step 3	spanning-tree vlan `vlan-id` priority `priority` Example: `Device(config)# spanning-tree vlan 20 priority 8192`	Configures the device priority of a VLAN. For `vlan-id` , you can specify a single VLAN identified by VLAN ID number, a range of VLANs separated by a hyphen, or a series of VLANs separated by a comma. The range is 1 to 4094. For `priority` , the range is 0 to 61440 in increments of 4096; the default is 32768. The lower the number, the more likely the device will be chosen as the root device. Valid priority values are 4096, 8192, 12288, 16384, 20480, 24576, 28672, 32768, 36864, 40960, 45056, 49152, 53248, 57344, and 61440. All other values are rejected.
Step 4	end Example: `Device(config-if)# end`	Returns to privileged EXEC mode.

Configuring the Hello Time

The hello time is the time interval between configuration messages generated and sent by the root device.

This procedure is optional.

SUMMARY STEPS

enable
spanning-tree vlan vlan-id hello-time seconds
end

DETAILED STEPS

Command or Action Purpose

Step 1

enable

Example:


Device> enable

Enables privileged EXEC mode.

Enter your password if prompted.

Step 2

spanning-tree vlan vlan-id hello-time seconds

Example:


Device(config)# spanning-tree vlan 20-24 hello-time 3

Configures the hello time of a VLAN. The hello time is the time interval between configuration messages generated and sent by the root device. These messages mean that the device is alive.

For vlan-id , you can specify a single VLAN identified by VLAN ID number, a range of VLANs separated by a hyphen, or a series of VLANs separated by a comma. The range is 1 to 4094.
For seconds , the range is 1 to 10; the default is 2.

Step 3

end

Example:


Device(config-if)# end

Returns to privileged EXEC mode.

Configuring the Forwarding-Delay Time for a VLAN

This procedure is optional.

SUMMARY STEPS

enable
configure terminal
spanning-tree vlan vlan-id forward-time seconds
end

DETAILED STEPS

	Command or Action	Purpose
Step 1	enable Example: `Device> enable`	Enables privileged EXEC mode. Enter your password if prompted.
Step 2	configure terminal Example: `Device# configure terminal`	Enters global configuration mode.
Step 3	spanning-tree vlan `vlan-id` forward-time `seconds` Example: `Device(config)# spanning-tree vlan 20,25 forward-time 18`	Configures the forward time of a VLAN. The forwarding delay is the number of seconds an interface waits before changing from its spanning-tree learning and listening states to the forwarding state. For `vlan-id` , you can specify a single VLAN identified by VLAN ID number, a range of VLANs separated by a hyphen, or a series of VLANs separated by a comma. The range is 1 to 4094. For `seconds` , the range is 4 to 30; the default is 15.
Step 4	end Example: `Device(config)# end`	Returns to privileged EXEC mode.

Configuring the Maximum-Aging Time for a VLAN

This procedure is optional.

SUMMARY STEPS

enable
configure terminal
spanning-tree vlan vlan-id max-age seconds
end

DETAILED STEPS

	Command or Action	Purpose
Step 1	enable Example: `Device> enable`	Enables privileged EXEC mode. Enter your password if prompted.
Step 2	configure terminal Example: `Device# configure terminal`	Enters global configuration mode.
Step 3	spanning-tree vlan `vlan-id` max-age `seconds` Example: `Device(config)# spanning-tree vlan 20 max-age 30`	Configures the maximum-aging time of a VLAN. The maximum-aging time is the number of seconds a device waits without receiving spanning-tree configuration messages before attempting a reconfiguration. For `vlan-id` , you can specify a single VLAN identified by VLAN ID number, a range of VLANs separated by a hyphen, or a series of VLANs separated by a comma. The range is 1 to 4094. For `seconds` , the range is 6 to 40; the default is 20.
Step 4	end Example: `Device(config-if)# end`	Returns to privileged EXEC mode.

Configuring the Transmit Hold-Count

You can configure the BPDU burst size by changing the transmit hold count value.

Note

Changing this parameter to a higher value can have a significant impact on CPU utilization, especially in Rapid PVST+ mode. Lowering this value can slow down convergence in certain scenarios. We recommend that you maintain the default setting.

This procedure is optional.

SUMMARY STEPS

enable
configure terminal
spanning-tree transmit hold-count value
end

DETAILED STEPS

	Command or Action	Purpose
Step 1	enable Example: `Device> enable`	Enables privileged EXEC mode. Enter your password if prompted.
Step 2	configure terminal Example: `Device# configure terminal`	Enters global configuration mode.
Step 3	spanning-tree transmit hold-count `value` Example: `Device(config)# spanning-tree transmit hold-count 6`	Configures the number of BPDUs that can be sent before pausing for 1 second. For `value` , the range is 1 to 20; the default is 6.
Step 4	end Example: `Device(config)# end`	Returns to privileged EXEC mode.

Monitoring Spanning-Tree Status

Table 4. Commands for Displaying Spanning-Tree Status

show spanning-tree active	Displays spanning-tree information on active interfaces only.
show spanning-tree detail	Displays a detailed summary of interface information.
show spanning-tree vlan `vlan-id`	Displays spanning-tree information for the specified VLAN.
show spanning-tree interface `interface-id`	Displays spanning-tree information for the specified interface.
show spanning-tree interface `interface-id` portfast	Displays spanning-tree portfast information for the specified interface.
show spanning-tree summary [totals]	Displays a summary of interface states or displays the total lines of the STP state section.

To clear spanning-tree counters, use the clear spanning-tree [interface interface-id] privileged EXEC command.

Bias-Free Language

Results

Chapter: Configuring Spanning Tree Protocol

Configuring Spanning Tree Protocol

Finding Feature Information

Restrictions for STP

Spanning Tree Protocol

Spanning-Tree Topology and BPDUs

Bridge ID, Device Priority, and Extended System ID

Port Priority Versus Path Cost

Spanning-Tree Interface States

Blocking State

Listening State

Learning State

Forwarding State

Disabled State

How a Device or Port Becomes the Root Device or Root Port

Spanning Tree and Redundant Connectivity

Spanning-Tree Address Management

Accelerated Aging to Retain Connectivity

Spanning-Tree Modes and Protocols

Supported Spanning-Tree Instances

Spanning-Tree Interoperability and Backward Compatibility

STP and IEEE 802.1Q Trunks

VLAN-Bridge Spanning Tree

Default Spanning-Tree Configuration

Changing the Spanning-Tree Mode

SUMMARY STEPS

DETAILED STEPS

Example:

Example:

Example:

Example:

Example:

Example:

Example:

Disabling Spanning Tree

SUMMARY STEPS

DETAILED STEPS

Example:

Example:

Example:

Example:

Configuring the Root Device

SUMMARY STEPS

DETAILED STEPS

Example:

Example:

Example:

Example:

What to do next

Configuring a Secondary Root Device

SUMMARY STEPS

DETAILED STEPS

Example:

Example:

Example:

Example:

Configuring Port Priority

SUMMARY STEPS

DETAILED STEPS

Example:

Example:

Example:

Example:

Example:

Example:

Configuring Path Cost

SUMMARY STEPS

DETAILED STEPS

Example:

Example:

Example:

Example:

Example:

Example:

Configuring the Device Priority of a VLAN

SUMMARY STEPS

DETAILED STEPS