Cisco Nexus 9000 Series NX-OS Command Reference (Configuration Commands), Release 7.0(3)I5(1)

name-lookup

[no] name-lookup

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
name-lookup	Display OSPF router ids as DNS names

Command Mode

/exec/configure/router-ospf /exec/configure/router-ospf/vrf

name-lookup

[no] name-lookup

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
name-lookup	Enable Name Lookup for OSPF Neighbors

Command Mode

/exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf

name

name <redundancy-name> | no name [ <redundancy-name> ]

Syntax Description

Syntax Description


no	Negate a command or set its defaults
name	Redundancy name
redundancy-name	Name String

Command Mode

/exec/configure/if-eth-any/glbp

name

name <name-val> | no name [ <name-val> ]

Syntax Description

Syntax Description


no	Negate a command or set its defaults
name	Set configuration name
name-val	Configuration name

Command Mode

/exec/configure/spanning-tree/mst/configuration

name

name [ <name> ] | no name

Syntax Description

Syntax Description


no	Negate a command or set its defaults
name	Redundancy name string
name	(Optional) name string

Command Mode

/exec/configure/if-eth-any/hsrp_ipv4 /exec/configure/if-eth-any/hsrp_ipv6

nat destination

{ nat destination } | { no nat destination }

Syntax Description

Syntax Description


no	Negate a command or set its defaults
nat	Network Address Translation
destination	Destination NAT

Command Mode

/exec/configure/itd

nat destination

{ nat destination } | { no nat destination }

Syntax Description

Syntax Description


no	Negate a command or set its defaults
nat	Network Address Translation
destination	Destination NAT

Command Mode

/exec/configure/itd

nbm flow bandwidth

[no] nbm flow bandwidth <i0>

Syntax Description

Syntax Description


nbm	Non Blocking Multicast
flow	Flow Characteristics
bandwidth	Bandwidth per flow
i0	Per Flow Bandwidth in Mbps

Command Mode

/exec/configure

negotiate auto

negotiate auto | no negotiate auto

Syntax Description

Syntax Description


no	Negate a command or set its defaults
negotiate	Configure link negotiation parameters
auto	Configure auto-negotiation

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel

neighbor-down fib-accelerate

[no] neighbor-down fib-accelerate

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
neighbor-down	Handle BGP neighbor down event, due to various reasons
fib-accelerate	Accelerate the hardware updates for IP/IPv6 adjacencies for neighbor

Command Mode

/exec/configure/router-bgp/vrf-cmds

neighbor

[no] neighbor { <neighbor-id> | <ipv6-neighbor-id> } [ remote-as <asn> ]

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
neighbor	Configure a BGP neighbor
neighbor-id	IP address of the neighbor
remote-as	(Optional) Specify Autonomous System Number of the neighbor
asn	(Optional) Autonomous System Number

Command Mode

/exec/configure/router-bgp

neighbor

[no] neighbor { <neighbor-id> | <ipv6-neighbor-id> } [ remote-as <asn> ]

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
neighbor	Configure a BGP neighbor
neighbor-id	IP address of the neighbor
remote-as	(Optional) Specify Autonomous System Number of the neighbor
asn	(Optional) Autonomous System Number

Command Mode

/exec/configure/router-bgp/router-bgp-vrf

neighbor

[no] neighbor { <neighbor-prefix> | <ipv6-neighbor-prefix> } [ remote-as [ <asn> | route-map <rmap-name> ] ]

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
neighbor	Configure a BGP neighbor
neighbor-prefix	IP prefix for neighbors
remote-as	(Optional) Specify Autonomous System Number of the neighbor
asn	(Optional) Autonomous System Number
route-map	(Optional) Route-map to match prefix peer AS number
rmap-name	(Optional) Route-map name

Command Mode

/exec/configure/router-bgp

neighbor

[no] neighbor { <neighbor-prefix> | <ipv6-neighbor-prefix> } [ remote-as [ <asn> | route-map <rmap-name> ] ]

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
neighbor	Configure a BGP neighbor
neighbor-prefix	IP prefix for neighbors
remote-as	(Optional) Specify Autonomous System Number of the neighbor
asn	(Optional) Autonomous System Number
route-map	(Optional) Route-map to match prefix peer AS number
rmap-name	(Optional) Route-map name

Command Mode

/exec/configure/router-bgp/router-bgp-vrf

neighbor

neighbor [ vrf { <vrf-name> | <vrf-known-name> } ] <ipaddr> { implicit-withdraw | labels accept <pfx-list> | targeted } | no neighbor [ vrf { <vrf-name> | <vrf-known-name> } ] <ipaddr> [ implicit-withdraw | labels accept | targeted ]

Syntax Description

Syntax Description


no	Negate a command or set its defaults
neighbor	Configure neighbor parameters
vrf	(Optional) VRF Routing/Forwarding instance information
vrf-name	(Optional) VPN Routing/Forwarding instance name
vrf-known-name	(Optional) Known VRF name
ipaddr	IP address for LDP neighbor
implicit-withdraw	Enable LDP Implicit Withdraw Label
labels	Configure label binding exchange controls
accept	Specify label bindings to accept
pfx-list	Name of prefix list
targeted	Establish targeted session

Command Mode

/exec/configure/ldp

neighbor maximum-prefix

{ { neighbor <address> { <interface> | maximum-prefix <value> [ warning-only ] } } | { no neighbor <address> [ <interface> | maximum-prefix <value> [ warning-only ] ] } } | { { neighbor maximum-prefix <value> [ <threshold> ] [ warning-only ] [ restart <time1> ] [ restart-count <count> ] [ reset-time <time2> ] [ dampened ] } | { no neighbor maximum-prefix [ <value> [ <threshold> ] [ warning-only ] [ restart <time1> ] [ restart-count <count> ] ] } }

Syntax Description

Syntax Description


no	Negate a command or set its defaults
neighbor	Specify a neighbor router
interface	Interface
address	Neighbor address
maximum-prefix	Maximum number of IP prefixes acceptable from a neighbor
value	Number of IP prefixes for maximum-prefix limit
threshold	(Optional) Threshold value (%) at which to generate a warning message
warning-only	(Optional) Only give warning message when limit is exceeded
restart	(Optional) Duration for which a prefix source is ignored
time1	(Optional) Restart interval in minutes
restart-count	(Optional) Number of times sessions are auto-restarted
count	(Optional) Number of times
reset-time	(Optional) Duration after which restart history is cleared
time2	(Optional) Reset time in minutes
dampened	(Optional) Exponentially increase restart time interval

Command Mode

/exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

net

[no] net <net>

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
net	Configure Network Entity Title for IS-IS
net	NET in form of XX.XXXX. ... .XXXX[.00]

Command Mode

/exec/configure/otv-isis

net

[no] net <net>

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
net	Configure Network Entity Title for IS-IS
net	NET in form of XX.XXXX. ... .XXXX[.00]

Command Mode

/exec/configure/router-isis/router-isis-vrf-common

network

[no] network { <ip-addr> mask <ip-mask> | <ip-prefix> } [ route-map <rmap-name> | summarize ] +

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
network	Configure an IP prefix to advertise
ip-addr	IP network to advertise
mask	Configure the mask of the IP prefix to advertise
ip-mask	Dotted 4-octet mask
ip-prefix	IP prefix in CIDR format
route-map	(Optional) Apply route-map to modify attributes
rmap-name	(Optional) Route-map name
summarize	(Optional) Summarize more specific prefixes from routing table

Command Mode

/exec/configure/router-bgp/router-bgp-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv4

network

[no] network <ipv6-prefix> [ route-map <rmap-name> | summarize ] +

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
network	Configure an IPv6 prefix to advertise
route-map	(Optional) Apply route-map to modify attributes
rmap-name	(Optional) Route-map name
summarize	(Optional) Summarize more specific prefixes from routing table

Command Mode

/exec/configure/router-bgp/router-bgp-af-ipv6 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6

network

[no] network { <ip-dest> <ip-mask> | <ip-prefix> }

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
network	RIP IP network
ip-dest	IP addr format
ip-mask	IP network mask format
ip-prefix	Exact prefix

Command Mode

/exec/configure/router-rip/router-rip-af-ipv4 /exec/configure/router-rip/router-rip-vrf-af-ipv4

network

[no] network { { <address> <mask> } | <prefix> }

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
network	Enable routing on an IP network
address	Network number
mask	EIGRP wild card bits
prefix	IP prefix in slash format

Command Mode

/exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-ipv4

network area

[no] network { <ip-dest> <ip-mask> | <ip-prefix> } area { <area-id-ip> | <area-id-int> }

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
network	Enable routing on an IP network
ip-dest	IP prefix format: i.i.i.i
ip-mask	IP network mask format: m.m.m.m
ip-prefix	IP prefix format: x.x.x.x/ml
area	Configure area properties
area-id-ip	OSPF area ID in IP address format
area-id-int	OSPF area ID as a decimal format

Command Mode

/exec/configure/router-ospf /exec/configure/router-ospf/vrf

next-address exclude-address

{ next-address [ loose | strict ] <ipaddr> | exclude-address <ipaddr> }

Syntax Description

Syntax Description


next-address	Specify the next address in the path
loose	(Optional) Target address is loose
strict	(Optional) Target address is strict
exclude-address	Exclude an address from subsequent partial path segments
ipaddr	Enter IP address (A.B.C.D)

Command Mode

/exec/configure/te/expl-path

next-hop-self

[ no | default ] next-hop-self

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
default	(Optional) Inherit values from a peer template
next-hop-self	Set our peering address as nexthop

Command Mode

/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label

next-hop-self

[ no | default ] next-hop-self

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
default	(Optional) Inherit values from a peer template
next-hop-self	Set our peering address as nexthop

Command Mode

/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt

next-hop-third-party

[ no | default ] next-hop-third-party

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
default	(Optional) Inherit values from a peer template
next-hop-third-party	Compute a third-party nexthop if possible

Command Mode

/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af

next-hop-third-party

[ no | default ] next-hop-third-party

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
default	(Optional) Inherit values from a peer template
next-hop-third-party	Compute a third-party nexthop if possible

Command Mode

/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt

next-hop out-label explicit-null implicit-null next-hop auto-resolve out-label explicit-null implicit-null

[no] { next-hop [ backup <interface> ] <next-hop> out-label { <static-outlabel> | explicit-null | implicit-null } | next-hop auto-resolve out-label { <static-outlabel> | explicit-null | implicit-null } }

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
next-hop	Nexthop
next-hop	Destination IPv4 next hop
static-outlabel	Label Value
interface	(Optional) Back up interface
out-label	Output label
explicit-null	IETF MPLS IPv4 explicit null label (0)
implicit-null	IETF MPLS implicit null label (3)
auto-resolve	auto resolve the destination path
backup	(Optional) Backup destination

Command Mode

/exec/configure/mpls_static/ipv4/input

next-hop out-label explicit-null implicit-null next-hop auto-resolve out-label explicit-null implicit-null

[no] { next-hop [ backup <interface> ] <ipv6-next-hop> out-label { <static-outlabel> | explicit-null | implicit-null } | next-hop auto-resolve out-label { <static-outlabel> | explicit-null | implicit-null } }

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
next-hop	Nexthop
static-outlabel	Label Value
interface	(Optional) Back up interface
out-label	Output label
explicit-null	IETF MPLS IPv6 explicit null label (2)
implicit-null	IETF MPLS implicit null label (3)
auto-resolve	auto resolve the destination path
backup	(Optional) Backup destination

Command Mode

/exec/configure/mpls_static/ipv6/input

nexthop route-map

[no] nexthop route-map <rmap-name>

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
nexthop	Nexthop tracking
route-map	Route map for valid nexthops
rmap-name	Route-map name

Command Mode

/exec/configure/router-bgp/router-bgp-af /exec/configure/router-bgp/router-bgp-af-l2vpn-evpn /exec/configure/router-bgp/router-bgp-af-link-state /exec/configure/router-bgp/router-bgp-af-ipv4-mvpn /exec/configure/router-bgp/router-bgp-af-ipv6-mvpn

nexthop route-map

[no] nexthop route-map <rmap-name>

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
nexthop	Nexthop tracking
route-map	Route map for valid nexthops
rmap-name	Route-map name

Command Mode

/exec/configure/router-bgp/router-bgp-af-ipv4-mdt /exec/configure/router-bgp/router-bgp-af-l2vpn-vpls

nexthop trigger-delay critical non-critical

{ nexthop trigger-delay critical <criticaldelay> non-critical <noncriticaldelay> } | { no nexthop trigger-delay }

Syntax Description

Syntax Description


no	Negate a command or set its defaults
nexthop	Nexthop tracking
trigger-delay	Set the delay to trigger nexthop tracking
critical	Nexthop changes affecting reachability
non-critical	Other nexthop changes
noncriticaldelay	Delay value (miliseconds)
criticaldelay	Delay value (miliseconds)

Command Mode

/exec/configure/router-bgp/router-bgp-af /exec/configure/router-bgp/router-bgp-af-ipv4-mdt /exec/configure/router-bgp/router-bgp-af-vpnv4 /exec/configure/router-bgp/router-bgp-af-vpnv6 /exec/configure/router-bgp/router-bgp-af-link-state /exec/configure/router-bgp/router-bgp-af-l2vpn-vpls /exec/configure/router-bgp/router-bgp-af-ipv4-mvpn /exec/configure/router-bgp/router-bgp-af-ipv6-mvpn /exec/configure/router-bgp/router-bgp-af-l2vpn-evpn

ngoam install acl

[no] ngoam install acl

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
ngoam	ngoam
install	Ngoam install
acl	Ngoam install acl

Command Mode

/exec/configure

ngoam install acl draft-pang action fwd

[no] ngoam install acl draft-pang action { fwd | drop }

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
ngoam	ngoam
install	Ngoam install
acl	Ngoam install acl
draft-pang	Ngoam install acl based on draft pang
action	Choose the action to perform
fwd	Copy and Forward the packet
drop	Copy and Drop the packet

Command Mode

/exec/configure

ngoam probe start

ngoam probe start <hex-string>

Syntax Description

Syntax Description


ngoam	ngoam exec command
probe	ngoam probe
start	start ngoam probe
hex-string	Specify string in hex string format: 0A1B .. starting with outer header of real draft pang probe packet

Command Mode

/exec

ngoam profile

[no] ngoam profile <profile-id>

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
ngoam	Configure ngoam oam
profile	Configure ngoam oam profile
profile-id	ngoam profile id

Command Mode

/exec/configure

no-more

| no-more

Syntax Description

Syntax Description


\|	Pipe command output to filter
no-more	Turn-off pagination for command output

Command Mode

/output

no

[no] { userprofile | trustedCert | CRLLookup | user-switch-bind | user-certdn-match | user-pubkey-match }

Syntax Description

Syntax Description


no	Negate a command or set its defaults
userprofile	Delete the userprofile
trustedCert	Delete the trustedCert
CRLLookup	Delete the CRLLookup
user-switch-bind	Delete the user-switch-bind
user-certdn-match	Delete the certificate matching
user-pubkey-match	Delete the pubkey matching

Command Mode

/exec/configure/ldap/search

node

[no] node [ ip <ip-addr> | IPv6 <ip-addrv6> ]

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
node	ITD node
ip	(Optional) ITD node IPv4 address
ip-addr	(Optional) ITD node IP4 prefix in format i.i.i.i
IPv6	(Optional) ITD node IPv6 address

Command Mode

/exec/configure/itd-device-group

node

[no] node [ ip <ip-addr> | IPv6 <ip-addrv6> ]

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
node	ITD node
ip	(Optional) ITD node IPv4 address
ip-addr	(Optional) ITD node IP4 prefix in format i.i.i.i
IPv6	(Optional) ITD node IPv6 address

Command Mode

/exec/configure/itd-session-device-group

node

[no] node [ ip <ip-addr> | IPv6 <ip-addrv6> ]

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
node	ITD node
ip	(Optional) ITD node IPv4 address
ip-addr	(Optional) ITD node IP4 prefix in format i.i.i.i
IPv6	(Optional) ITD node IPv6 address

Command Mode

/exec/configure/itd-device-group

nsf await-redist-proto-convergence

{ [ no ] nsf await-redist-proto-convergence }

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
nsf	Non-stop forwarding
await-redist-proto-convergence	Specify whether EIGRP should wait for other protocols to converge before advertising routes

Command Mode

/exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

ntp access-group

[no] ntp access-group { peer | serve-only | serve | query-only } <acl-name>

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its default
ntp	NTP configuration
access-group	NTP access-group
peer	access-group peer
serve	access-group serve
serve-only	access-group serve-only
query-only	access-group query-only
acl-name	Name of access list

Command Mode

/exec/configure

ntp allow private

[no] ntp allow { private | control [ rate-limit <delay> ] }

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its default
ntp	NTP configuration
allow	Enable/Disable the packets
private	Enable/Disable Private mode packets
control	Enable/Disable Control mode packets
rate-limit	(Optional) Rate-limit the control packets
delay	(Optional) Rate-limit delay (Default 3)

Command Mode

/exec/configure

ntp authenticate

[no] ntp authenticate

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its default
ntp	NTP configuration
authenticate	Enable/Disable authentication

Command Mode

/exec/configure

ntp authentication-key md5

[no] ntp authentication-key <number> md5 <md5> [ 0 | 7 ]

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its default
ntp	NTP configuration
authentication-key	NTP authentication key
number	authentication key number (range 1-65535)
md5	use md5 authentication scheme
md5	MD5 string
0	(Optional) clear text
7	(Optional) encrypted

Command Mode

/exec/configure

ntp clear internal buffer

Syntax Description

Syntax Description


ntp	NTP configuration
clear	clear
internal	internal
buffer	debug message buffer

Command Mode

/exec

ntp drop-aged-packet

[no] ntp drop-aged-packet

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
ntp	NTP Configuration
drop-aged-packet	Enable or disable Riviera Timestamp Check.

Command Mode

/exec/configure

ntp enable ntpd-logfile debug-level

[no] ntp enable ntpd-logfile debug-level <level>

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its default
ntp	NTP configuration
enable	Enable logging
ntpd-logfile	NTP daemon logs
debug-level	debug level of logs
level	debug level of logs

Command Mode

/exec/configure

ntp logging

[no] ntp logging

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its default
ntp	NTP configuration
logging	Enable/Disable logging of NTPD Events

Command Mode

/exec/configure

ntp master

[no] ntp master [ <stratum-no> ]

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its default
ntp	NTP configuration
master	Act as NTP master clock
stratum-no	(Optional) Stratum number

Command Mode

/exec/configure

ntp passive

[no] ntp passive

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its default
ntp	NTP configuration
passive	NTP passive command

Command Mode

/exec/configure

ntp peer

[no] ntp peer <host0> [ prefer | key <keyid> | use-vrf { <vrf-name> | <vrf-known-name> } | minpoll <minpoll> | maxpoll <maxpoll> ] +

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
ntp	NTP Configuration
peer	NTP Peer address
host0	Hostname/IP address of the NTP Peer
prefer	(Optional) Preferred Server
key	(Optional) Keyid to be used while communicating to this server
keyid	(Optional) Value of keyid 1-65535
use-vrf	(Optional) Display per-VRF information
vrf-name	(Optional) VRF name
vrf-known-name	(Optional) Known VRF name
minpoll	(Optional) Minimum interval to poll a peer
minpoll	(Optional) Poll interval in secs to a power of 2 [default 4]
maxpoll	(Optional) Maximum interval to poll a peer
maxpoll	(Optional) Poll interval in secs to a power of 2 [default 6]

Command Mode

/exec/configure

ntp rts-update

[no] ntp rts-update

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
ntp	NTP Configuration
rts-update	Enable or disable RTS update to linecards.

Command Mode

/exec/configure

ntp server

[no] ntp server <host0> [ prefer | key <keyid> | use-vrf { <vrf-name> | <vrf-known-name> } | minpoll <minpoll> | maxpoll <maxpoll> ] +

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
ntp	NTP Configuration
server	NTP server address
host0	Hostname/IP address of the NTP Server
prefer	(Optional) Preferred Server
key	(Optional) Keyid to be used while communicating to this server
keyid	(Optional) Value of keyid 1-65535
use-vrf	(Optional) Display per-VRF information
vrf-name	(Optional) VRF name
vrf-known-name	(Optional) Known VRF name
minpoll	(Optional) Minimum interval to poll a server
minpoll	(Optional) Poll interval in secs to a power of 2 [default 4]
maxpoll	(Optional) Maximum interval to poll a server
maxpoll	(Optional) Poll interval in secs to a power of 2 [default 6]

Command Mode

/exec/configure

ntp source-interface

[no] ntp source-interface <interface>

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its default
ntp	NTP configuration
source-interface	Source interface sending NTP packets
interface	Source interface

Command Mode

/exec/configure

ntp source

[no] ntp source <ip-addr>

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its default
ntp	NTP Configuration
source	Source of NTP packets
ip-addr	IPv4/IPv6 address

Command Mode

/exec/configure

ntp sync-retry

Syntax Description

Syntax Description


ntp	NTP configuration
sync-retry	Retry synchronization with configured servers

Command Mode

/exec

ntp trusted-key

[no] ntp trusted-key <number>

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its default
ntp	NTP configuration
trusted-key	NTP trusted-key
number	trusted-key number

Command Mode

/exec/configure

nv overlay evpn

[no] nv overlay evpn

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
nv	Command to enable/disable features
overlay	Command to enable/disable features
evpn	Enable/Disable Ethernet VPN (EVPN)

Command Mode

/exec/configure

nve interface remap-replication-servers

nve interface <nve-if> remap-replication-servers

Syntax Description

Syntax Description


nve	Configure NVE information
interface	Interface
nve-if	NVE interface
remap-replication-servers	Remap Replication servers to VNIs

Command Mode

/exec

nve interface replication-server up

nve interface <nve-if> replication-server <rep-addr> { up | down }

Syntax Description

Syntax Description


nve	Configure NVE information
interface	Interface
nve-if	NVE interface
replication-server	Configure a replication server
rep-addr	Replication Server IP Address
up	mark replication-server up
down	mark replication-server down

Command Mode

/exec

nve oam mode draft-pang

[no] nve oam mode draft-pang

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
nve	VxLAN functionality
oam	VxLAN OAM functionality
mode	Choose operation mode for OAM
draft-pang	OAM implementation as per Draft Pang

Command Mode

/exec/configure

nxapi certificate

{ nxapi certificate { { httpskey { keyfile <uri0> | <line> } } | { httpscrt { certfile <uri1> | <line1> } } | { enable } } }

Syntax Description

Syntax Description


nxapi	Configure nxapi
certificate	Https certificate configuration
httpskey	Https private key
httpscrt	Https certificate
keyfile	Https key file
certfile	Https certificate file
enable	Enable the current certificate
uri0	File containing https private key for the user
line	nxapi https private key
uri1	File containing https certificate
line1	nxapi https certificate

Command Mode

/exec/configure

nxapi flow

{ [ no ] nxapi flow }

Syntax Description

Syntax Description


no	(Optional) Negate a command or set its defaults
nxapi	Configure nxapi
flow	allow frontend to access /sys/flow/

Command Mode

/exec/configure

nxapi http port

{ nxapi { http | https } port <s0> } | { no nxapi { http | https } } | { no nxapi { http | https } port <s0> }

Syntax Description

Syntax Description


no	Negate a command or set its defaults
nxapi	Configure nxapi
s0	Port number. Please do not use well-known protocol ports
http	Http configuration
https	Https configuration
port	Port number

Command Mode

/exec/configure

nxapi use-vrf management default

{ nxapi use-vrf { management | default | <vrf_name> } } | { no nxapi use-vrf { management | default | <vrf_name> } }

Syntax Description

Syntax Description


no	Negate a command or set its defaults
nxapi	Configure nxapi
use-vrf	vrf to be used for nxapi communication
management	management vrf
default	default vrf
vrf_name	name of the vrf

Command Mode

/exec/configure

Bias-Free Language

Results

Chapter: N Commands

N Commands

name-lookup

Syntax Description

name-lookup

Syntax Description

name

Syntax Description

name

Syntax Description

name

Syntax Description

nat destination

Syntax Description

nat destination

Syntax Description

nbm flow bandwidth

Syntax Description

negotiate auto

Syntax Description

neighbor-down fib-accelerate

Syntax Description

neighbor

Syntax Description

neighbor

Syntax Description

neighbor

Syntax Description

neighbor

Syntax Description

neighbor

Syntax Description

neighbor maximum-prefix

Syntax Description

net

Syntax Description

net

Syntax Description

network

Syntax Description

network

Syntax Description

network

Syntax Description

network

Syntax Description

network area

Syntax Description

next-address exclude-address

Syntax Description

next-hop-self

Syntax Description

next-hop-self

Syntax Description

next-hop-third-party

Syntax Description

next-hop-third-party

Syntax Description

next-hop out-label explicit-null implicit-null next-hop auto-resolve out-label explicit-null implicit-null

Syntax Description

next-hop out-label explicit-null implicit-null next-hop auto-resolve out-label explicit-null implicit-null

Syntax Description

nexthop route-map

Syntax Description

nexthop route-map

Syntax Description

nexthop trigger-delay critical non-critical

Syntax Description

ngoam install acl

Syntax Description

ngoam install acl draft-pang action fwd

Syntax Description

ngoam probe start

Syntax Description

ngoam profile

Syntax Description

no-more