H Commands

ha-policy single

ha-policy { single-sup <hap-change> | dual-sup <sw-change> } +

Syntax Description

Syntax Description

ha-policy

Change HA policy for this VDC

hap-change

Change HA policy for this VDC

single-sup

Change HA policy for this VDC for single-sup situations

dual-sup

Change HA policy for this VDC for dual-sup situations

sw-change

Set hap policy
Command Mode
  • /exec/configure/vdc

ha-stateful

[no] ha-stateful

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

ha-stateful

Enable stateful OSPF HA
Command Mode
  • /exec/configure/router-ospf

hardware access-list lou resource threshold

[no] hardware access-list lou resource threshold <threshold>

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Hardware Internal Information

access-list

Access Control List

lou

LOU

resource

hardware resource

threshold

port expansion threshold

threshold

value of threshold
Command Mode
  • /exec/configure

hardware access-list match inner-header

[no] hardware access-list match inner-header

Syntax Description

Syntax Description

no

(Optional) Negate the command or set its defaults

hardware

Change hardware usage settings

access-list

Access Control List

match

Match criteria in ACL

inner-header

Match inner header fields in IPinIP/GRE packets
Command Mode
  • /exec/configure

hardware access-list module

[no] hardware access-list { resource-pooling | resource pooling } module <module-number>

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Show hardware information

access-list

Access Control List

resource-pooling

Enable ACL programming across TCAM banks

resource

hardware resource

pooling

Enable ACL programming across TCAM banks

module

module number

module-number

specify module number
Command Mode
  • /exec/configure

hardware access-list tcam region

[no] hardware access-list tcam region <type> <tcam_size>

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Hardware Internal Information

access-list

Access Control List

tcam

Configure tcam parameters

region

Configure tcam region

type

Region type

tcam_size

Enter tcam size
Command Mode
  • /exec/configure

hardware access-list tcam region double-wide

[no] hardware access-list tcam region <double-wide-region> <tcam_size> double-wide

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Hardware Internal Information

access-list

Access Control List

tcam

Configure tcam parameters

region

Configure tcam region

double-wide-region

Region type

tcam_size

Enter tcam size

double-wide

Double Width
Command Mode
  • /exec/configure

hardware access-list tcam region double-wide

[no] hardware access-list tcam region <arp-ether> <arpether_tcam_size> double-wide

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Hardware Internal Information

access-list

Access Control List

tcam

Configure tcam parameters

region

Configure tcam region

arp-ether

Region type

arpether_tcam_size

Enter tcam size

double-wide

Double Width
Command Mode
  • /exec/configure

hardware access-list tcam region qualify udf

[no] hardware access-list tcam region <udf_tcam_type> qualify udf { <udf_name> } +

Syntax Description

Syntax Description

no

(Optional) Negate the command

hardware

Change hardware usage settings

access-list

Access Control List

tcam

Configure tcam parameters

region

Configure tcam region

udf_tcam_type

Region type

qualify

Configure UDFs to be qualified for span region

udf

Configure UDF names

udf_name

UDF name
Command Mode
  • /exec/configure

hardware ecmp hash-offset

[no] hardware ecmp hash-offset <value> [ concatenation ]

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Change hardware usage settings

ecmp

ECMP configuration

hash-offset

Configure hash offset

value

Hash offset 0-15 non-concatenate mode, 0-63 concatenate mode

concatenation

(Optional) Configure hash concatenation
Command Mode
  • /exec/configure

hardware ecmp hash-polynomial

hardware ecmp hash-polynomial <poly-type> | no hardware ecmp hash-polynomial

Syntax Description

Syntax Description

no

Negate a command or set its defaults

hardware

Change hardware usage settings

ecmp

ECMP configuration

hash-polynomial

Configure hash polynomial

poly-type

Polynomial type
Command Mode
  • /exec/configure

hardware ejector enable

[no] hardware ejector enable

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Hardware Internal Information

ejector

Card ejector functionality

enable

enabled means when both ejectors are open, card is powered down
Command Mode
  • /exec/configure

hardware fan-zone raise-speed

[no] hardware fan-zone <fan_zone_id> raise-speed <speed-to-raise>

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Hardware Internal Information

fan-zone

Fan Zone supported in the switch

fan_zone_id

please enter fan zone id whose speed needs to be increased

raise-speed

Speed to be added for current fan zone speed

speed-to-raise

please enter additional fan speed
Command Mode
  • /exec/configure

hardware forwarding funcstats clear

hardware forwarding funcstats clear

Syntax Description

Syntax Description

hardware

Change hardware usage settings

forwarding

Change forwarding related settings

funcstats

Enable/disable funcstats

clear

Clear funcstats information
Command Mode
  • /exec

hardware forwarding funcstats disable

hardware forwarding funcstats disable

Syntax Description

Syntax Description

hardware

Change hardware usage settings

forwarding

Change forwarding related settings

funcstats

Enable/disable funcstats

disable

Disable funcstats recording and output
Command Mode
  • /exec

hardware forwarding funcstats enable

hardware forwarding funcstats enable

Syntax Description

Syntax Description

hardware

Change hardware usage settings

forwarding

Change forwarding related settings

funcstats

Enable/disable funcstats

enable

Enable funcstats recording and output
Command Mode
  • /exec

hardware forwarding l3 resource route non-deterministic

[no] hardware forwarding l3 resource route non-deterministic

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

hardware information

forwarding

forwarding information

l3

Layer-3

resource

hardware resources

route

TCAM capacity to hold prefixes

non-deterministic

extend upto 1M
Command Mode
  • /exec/configure

hardware forwarding unicast trace

[no] hardware forwarding unicast trace

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Hardware Internal Information

forwarding

Hardware forwarding

unicast

Hardware Unicast forwarding

trace

Debug traces
Command Mode
  • /exec/configure

hardware ip glean throttle

[no] hardware ip glean throttle

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Hardware information

ip

IP

glean

Glean

throttle

Throttle
Command Mode
  • /exec/configure

hardware ip glean throttle maximum

{ hardware ip glean throttle maximum <count> } | { no hardware ip glean throttle maximum }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

hardware

Hardware information

ip

IP

glean

Glean

throttle

Throttle

maximum

Maximum number of entries

count

Count
Command Mode
  • /exec/configure

hardware ip glean throttle syslog

{ hardware ip glean throttle syslog <pkt-count> } | { no hardware ip glean throttle syslog }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

hardware

Hardware information

ip

IP

glean

Glean

throttle

Throttle

syslog

Threshold for syslog for number of packets hitting the entry

pkt-count

Packet count
Command Mode
  • /exec/configure

hardware ip glean throttle timeout

{ hardware ip glean throttle timeout <timeout-in-sec> } | { no hardware ip glean throttle timeout }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

hardware

Hardware information

ip

IP

glean

Glean

throttle

Throttle

timeout

Timeout

timeout-in-sec

Timeout value in seconds (should be multiple of 30, else will be rounded off to nearest boundary)
Command Mode
  • /exec/configure

hardware ipv6 glean throttle

[no] hardware ipv6 glean throttle

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Hardware information

ipv6

IPv6

glean

Glean

throttle

Throttle
Command Mode
  • /exec/configure

hardware ipv6 glean throttle maximum

{ hardware ipv6 glean throttle maximum <count> } | { no hardware ipv6 glean throttle maximum }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

hardware

Hardware information

ipv6

IPv6

glean

Glean

throttle

Throttle

maximum

Maximum number of entries

count

Count
Command Mode
  • /exec/configure

hardware ipv6 glean throttle syslog

{ hardware ipv6 glean throttle syslog <pkt-count> } | { no hardware ipv6 glean throttle syslog }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

hardware

Hardware information

ipv6

IPv6

glean

Glean

throttle

Throttle

syslog

Threshold for syslog for number of packets hitting the entry

pkt-count

Packet count
Command Mode
  • /exec/configure

hardware ipv6 glean throttle timeout

{ hardware ipv6 glean throttle timeout <timeout-in-sec> } | { no hardware ipv6 glean throttle timeout }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

hardware

Hardware information

ipv6

IPv6

glean

Glean

throttle

Throttle

timeout

Timeout

timeout-in-sec

Timeout value in seconds (should be multiple of 30, else will be rounded off to nearest boundary)
Command Mode
  • /exec/configure

hardware module boot-order reverse

[no] hardware module boot-order reverse

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Hardware Internal Information

module

applies on all the modules

boot-order

Configure order of module power-up

reverse

reverse order of module power-up
Command Mode
  • /exec/configure

hardware profile buffer info poll-interval timer

[no] hardware profile buffer info poll-interval [ module <module> ] timer <msec>

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Change hardware usage settings

profile

profile settings

buffer

System buffer

info

Information

poll-interval

System buffer status polling interval

module

(Optional) Slot/module

module

(Optional) Slot/module number

timer

Polling timer

msec

Polling timer value in msecs
Command Mode
  • /exec/configure

hardware profile buffer info port-threshold threshold

[no] hardware profile buffer info port-threshold [ module <module> ] threshold <value>

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Change hardware usage settings

profile

profile settings

buffer

System buffer

info

Information

port-threshold

Set port egress buffer usage threshold

module

(Optional) Slot/module

module

(Optional) Slot/module number

threshold

threshold value

value

percentage of maximum usage
Command Mode
  • /exec/configure

hardware profile ecmp auto-recovery threshold

hardware profile ecmp auto-recovery threshold <percentage> | no hardware profile ecmp auto-recovery threshold

Syntax Description

Syntax Description

no

Negate a command or set its defaults

hardware

Change hardware usage settings

profile

profile settings

ecmp

ECMP settings

auto-recovery

ECMP auto-recovery settings

threshold

ECMP table free percentage threshold for auto-recovery

percentage

Percentage
Command Mode
  • /exec/configure

hardware profile ecmp resilient

[no] hardware profile ecmp resilient

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Change hardware usage settings

profile

profile settings

ecmp

ECMP settings

resilient

Configure ECMP resilient mode
Command Mode
  • /exec/configure

hardware profile front portmode

hardware profile front portmode <port-mode> | no hardware profile front portmode

Syntax Description

Syntax Description

no

Negate a command or set its defaults

hardware

Change hardware usage settings

profile

profile settings

front

port 1 QSFP/SFP+ settings

portmode

QSFP or SFP+

port-mode

Configure QSFP/sfp+ port mode
Command Mode
  • /exec/configure

hardware profile ipv6 alpm carve-value

[no] hardware profile ipv6 alpm carve-value <ipv6_alpm_carve_value>

Syntax Description

Syntax Description

no

(Optional) Negate the command

hardware

Change hardware usage settings

profile

profile settings

ipv6

ipv6

alpm

alpm mode

carve-value

carve value

ipv6_alpm_carve_value

maximum entries
Command Mode
  • /exec/configure

hardware profile ipv6 lpm-entries maximum

[no] hardware profile ipv6 lpm-entries maximum <ipv6_lpm_max_entry>

Syntax Description

Syntax Description

no

(Optional) Negate the command

hardware

Change hardware usage settings

profile

profile settings

ipv6

ipv6

lpm-entries

lpm(non-host) entries

maximum

maximum limit

ipv6_lpm_max_entry

maximum entries
Command Mode
  • /exec/configure

hardware profile multicast max-limit

{ hardware profile multicast max-limit <mcast-ent> } | { no hardware profile multicast max-limit }

Syntax Description

Syntax Description

no

Negate the command

hardware

Change hardware usage settings

profile

profile settings

multicast

Multicast settings

max-limit

maximum limit for multicast entries

mcast-ent

Mcast Table Entries
Command Mode
  • /exec/configure

hardware profile multicast max-limit lpm-entries

[no] hardware profile multicast max-limit lpm-entries <ipv4_mcast_lpm_max_entry>

Syntax Description

Syntax Description

no

(Optional) Negate the command

hardware

Change hardware usage settings

profile

profile settings

multicast

Multicast settings

max-limit

maximum limit for multicast entries

lpm-entries

lpm(non-host) entries

ipv4_mcast_lpm_max_entry

maximum entries
Command Mode
  • /exec/configure

hardware profile multicast prefer-source-tree

[no] hardware profile multicast prefer-source-tree [ eternity [ limit <max-limit> ] ]

Syntax Description

Syntax Description

no

(Optional) Negate the command

hardware

Change hardware usage settings

profile

profile settings

multicast

Multicast settings

prefer-source-tree

prefer the source tree

eternity

(Optional) prefer source tree for eternity and not for just 2 minutes

limit

(Optional) Configure a limit for the number of hardware entries used

max-limit

(Optional) Number of (S,G) for which source tree is preferred
Command Mode
  • /exec/configure

hardware profile multicast syslog-threshold

[no] hardware profile multicast syslog-threshold <percentage>

Syntax Description

Syntax Description

no

(Optional) Negate the command

hardware

Change hardware usage settings

profile

profile settings

multicast

Multicast settings

syslog-threshold

MROUTE table syslog threshold

percentage

Percentage (Default is 90)
Command Mode
  • /exec/configure

hardware profile openflow

[no] hardware profile { openflow [ agent default { drop | normal } ] | { tap-aggregation [ l2drop ] } }

Syntax Description

Syntax Description

no

(Optional) Negate the command

hardware

Hardware Internal Information

profile

Profile

openflow

Openflow

tap-aggregation

Tap Aggregation

l2drop

(Optional) Drop non IP traffic ingress on mode tap interfaces

agent

(Optional) Act as Openflow Agent

default

(Optional) Specify default action for frames which don't match any flow

drop

(Optional) Drop all frames that miss MAC

normal

(Optional) [default]Flood unknown traffic
Command Mode
  • /exec/configure

hardware profile pfc mmu buffer-reservation

[no] hardware profile pfc mmu buffer-reservation <percentage>

Syntax Description

Syntax Description

no

(Optional) Negate the command

hardware

Hardware Internal Information

profile

profile settings

pfc

System level priority-flow-control settings

mmu

Hardware memory management unit configuration

buffer-reservation

Shared pool buffer reservation

percentage

Percentage of shared pool buffers to be reserved
Command Mode
  • /exec/configure

hardware profile portmode

{ hardware profile portmode <port-mode> [ 2-tuple ] } | no hardware profile portmode

Syntax Description

Syntax Description

no

Negate a command or set its defaults

hardware

Change hardware usage settings

profile

profile settings

portmode

QSFP port mode setting

port-mode

Configure QSFP port mode

2-tuple

(Optional) Display QSFP portnames in 2-tuple mode even in 10G mode
Command Mode
  • /exec/configure

hardware profile tcam ipv6-sup-tcam match-inner

{ hardware profile tcam ipv6-sup-tcam match-inner } | { no hardware profile tcam ipv6-sup-tcam match-inner }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

hardware

Change hardware usage settings

profile

Profile settings

tcam

Configure tcam parameters

ipv6-sup-tcam

IPv6 SUP TCAM parameters

match-inner

match inner payload for tunnel packets
Command Mode
  • /exec/configure

hardware profile tcam region

[no] hardware profile tcam region { <tcam_compat_type> <tcam_compat_size> | ifacl <tcam_compat_size> [ double-wide ] }

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Hardware Internal Information

profile

profile

tcam

Configure tcam parameters

region

Configure tcam region

ifacl

IPV4 PACL size

double-wide

(Optional) Configure tcam as double wide

tcam_compat_type

tcam_compat_size

Enter tcam size
Command Mode
  • /exec/configure

hardware profile tcam region span qualify udf

[no] hardware profile tcam region span qualify udf { <udf_name> } +

Syntax Description

Syntax Description

no

(Optional) Negate the command

hardware

Change hardware usage settings

profile

Profile settings

tcam

Configure tcam parameters

region

Configure tcam region

span

Configure for span region

qualify

Configure UDFs to be qualified for span region

udf

Configure UDF names

udf_name

UDF name
Command Mode
  • /exec/configure

hardware profile tcam resource service-template

[no] hardware profile tcam resource service-template { <name> } [ module { <lc> | <fm> } ]

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Change hardware usage settings

profile

Profile settings

tcam

Configure tcam parameters

resource

Configure tcam hardware resources

service-template

Commit template

name

Select name of template

module

(Optional) Specify a module number

lc

(Optional) line card number

fm

(Optional) fabric module number
Command Mode
  • /exec/configure handle auto 424

hardware profile tcam resource template

[no] hardware profile tcam resource template { <name> { ref-template <temp-nontahoe> | ref-template-tahoe <temp-tahoe> } }

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hardware

Change hardware usage settings

profile

Profile settings

tcam

Configure tcam parameters

resource

Configure tcam hardware resources

template

Configure template based tcam carving parameters

ref-template

Select a default template as reference

temp-nontahoe

ref-template-tahoe

Select a default template as reference

temp-tahoe

name

Create/Select name of custom template
Command Mode
  • /exec/configure

hardware profile ucast6 lpm-65-to-127-max-limit

{ hardware profile ucast6 lpm-65-to-127-max-limit <unicast-ent> } | { no hardware profile ucast6 lpm-65-to-127-max-limit }

Syntax Description

Syntax Description

no

Negate the command

hardware

Change hardware usage settings

profile

profile settings

ucast6

unicast ipv6 settings

lpm-65-to-127-max-limit

maximum limit for unicast ipv6 lpm-65-to-127 entries, default is 256

unicast-ent

Unicast ipv6 lpm-65-to-127 Table Entries
Command Mode
  • /exec/configure

hardware profile ucast6 max-limit

{ hardware profile ucast6 max-limit <unicast-ent> } | { no hardware profile ucast6 max-limit }

Syntax Description

Syntax Description

no

Negate the command

hardware

Change hardware usage settings

profile

profile settings

ucast6

unicast ipv6 settings

max-limit

maximum limit for unicast ipv6 entries

unicast-ent

Unicast ipv6 Table Entries
Command Mode
  • /exec/configure

hardware profile unicast enable-host-ecmp

[no] hardware profile unicast enable-host-ecmp [ arp-nd | [ ipv4 [ arp ] ] | [ ipv6 [ nd ] ] ]

Syntax Description

Syntax Description

no

(Optional) Negate the command

hardware

Change hardware usage settings

profile

profile settings

unicast

Unicast settings

enable-host-ecmp

Enable ECMP support for /32 (IPv4) and /128 (IPv6) routes

ipv4

(Optional) Enable ECMP support for /32 (IPv4 Only) Routes

ipv6

(Optional) Enable ECMP support for /128 (IPv6 Only) Routes

arp-nd

(Optional) Retain ARP (IPv4) and ND (IPv6) Routes in Host-Table

arp

(Optional) Retain ARP Entries in Host-Table

nd

(Optional) Retain ND Entries in Host-Table
Command Mode
  • /exec/configure

hardware profile unicast syslog-threshold

{ hardware profile unicast syslog-threshold <percentage> } | { no hardware profile unicast syslog-threshold }

Syntax Description

Syntax Description

no

Negate the command

hardware

Change hardware usage settings

profile

profile settings

unicast

Unicast settings

syslog-threshold

Unicast Route table syslog threshold

percentage

Percentage
Command Mode
  • /exec/configure

hardware sample-redirect module redirect-interface

hardware sample-redirect module <num> redirect-interface <interface>

Syntax Description

Syntax Description

hardware

Change hardware usage settings

sample-redirect

Redirect netflow sampled data

module

Line card module

num

slot number

redirect-interface

Interface for redirecting the traffic

interface

Interface Name
Command Mode
  • /exec

head

| head [ -n <lines> ]

Syntax Description

Syntax Description

|

Pipe command output to filter

head

Display first lines

-n

(Optional) modify number of lines (default 10)

lines

(Optional) number of lines to print
Command Mode
  • /output

hello-interval

{ { hello-interval <interval> } | { no hello-interval [ <interval> ] } }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

hello-interval

Hello interval

interval

(seconds)
Command Mode
  • /exec/configure/router-ospf/router-ospf-vlink /exec/configure/router-ospf/vrf/router-ospf-vlink

hello-interval

{ { hello-interval <interval> } | { no hello-interval [ <interval> ] } }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

hello-interval

Hello interval

interval

(seconds)
Command Mode
  • /exec/configure/router-ospf/vrf/router-ospf-slink

hello-interval

{ { hello-interval <interval> } | { no hello-interval [ <interval> ] } }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

hello-interval

Hello interval

interval

(seconds)
Command Mode
  • /exec/configure/router-ospf3/router-ospf3-vlink /exec/configure/router-ospf3/vrf/router-ospf3-vlink

hex

hex <expr>

Syntax Description

Syntax Description

hex

calculator with results in decimal format

expr

the expression to compute (integer arithmetics)
Command Mode
  • /exec

history

{ no | default } history { { buckets-kept } | { distributions-of-statistics-kept } | { enhanced [ interval [ <interval-seconds> [ buckets [ <num-buckets> ] ] ] ] } | { filter } | { hours-of-statistics-kept } | { lives-kept } | { statistics-distribution-interval } }

Syntax Description

Syntax Description

no

interval

(Optional) buckets

default

Set a command to its defaults

history

History and Distribution Data

buckets-kept

Maximum number of history buckets to collect

distributions-of-statistics-kept

Maximum number of statistics distribution buckets to capture

enhanced

Enable enhanced history collection

interval-seconds

(Optional) Interval in seconds

buckets

(Optional) Number of buckets to collect data

num-buckets

(Optional) Number of buckets

filter

Add operation to History when...

hours-of-statistics-kept

Maximum number of statistics hour groups to capture

lives-kept

Maximum number of history lives to collect

statistics-distribution-interval

Statistics distribution interval size
Command Mode
  • /exec/configure/ip-sla/udp /exec/configure/ip-sla/tcp /exec/configure/ip-sla/icmpEcho

history

history { { buckets-kept <num-buckets-kept> } | { distributions-of-statistics-kept <num-dist-stats> } | { enhanced [ interval [ <interval-seconds> [ buckets [ <num-buckets> ] ] ] ] } | { filter { all | failures | none | overThreshold } } | { hours-of-statistics-kept <num-hours-of-stats> } | { lives-kept <life-size-value> } | { statistics-distribution-interval <dist-interval> } }

Syntax Description

Syntax Description

interval

(Optional) buckets

interval-seconds

(Optional) <num-buckets>

life-size-value

<dist-interval>

history

History and Distribution Data

buckets-kept

Maximum number of history buckets to collect

num-buckets-kept

Bucket size value (default 15)

distributions-of-statistics-kept

Maximum number of statistics distribution buckets to capture

num-dist-stats

Distribution bucket size value (default 1)

enhanced

Enable enhanced history collection

buckets

(Optional) Number of buckets to collect data

num-buckets

(Optional) Number of buckets

filter

Add operation to History when...

all

Collect every operation in History

failures

Collect operations that fail in History

none

Shutoff History collection

overThreshold

Collect operations that are over threshold in History

hours-of-statistics-kept

Maximum number of statistics hour groups to capture

num-hours-of-stats

Hour groups size value (default 2)

lives-kept

Maximum number of history lives to collect

statistics-distribution-interval

Statistics distribution interval size

dist-interval

Distribution interval value in msec (default 20)
Command Mode
  • /exec/configure/ip-sla/udp /exec/configure/ip-sla/tcp /exec/configure/ip-sla/icmpEcho

history

{ no | default } history { { buckets-kept } | { distributions-of-statistics-kept } | { filter } | { hours-of-statistics-kept } | { lives-kept } | { statistics-distribution-interval } }

Syntax Description

Syntax Description

no

default

Set a command to its defaults

history

History and Distribution Data

buckets-kept

Maximum number of history buckets to collect

distributions-of-statistics-kept

Maximum number of statistics distribution buckets to capture

filter

Add operation to History when...

hours-of-statistics-kept

Maximum number of statistics hour groups to capture

lives-kept

Maximum number of history lives to collect

statistics-distribution-interval

Statistics distribution interval size
Command Mode
  • /exec/configure/ip-sla/dns /exec/configure/ip-sla/fabricPathEcho

history

history { { buckets-kept <num-buckets-kept> } | { distributions-of-statistics-kept <num-dist-stats> } | { filter { all | failures | none | overThreshold } } | { hours-of-statistics-kept <num-hours-of-stats> } | { lives-kept <life-size-value> } | { statistics-distribution-interval <dist-interval> } }

Syntax Description

Syntax Description

dist-interval

<num-buckets-kept>

num-hours-of-stats

<life-size-value>

distributions-of-statistics-kept

hours-of-statistics-kept

statistics-distribution-interval

history

History and Distribution Data

buckets-kept

Maximum number of history buckets to collect

num-buckets-kept

Bucket size value (default 15)

num-dist-stats

Distribution bucket size value (default 1)

filter

Add operation to History when...

all

Collect every operation in History

failures

Collect operations that fail in History

none

Shutoff History collection

overThreshold

Collect operations that are over threshold in History

hours-of-statistics-kept

Maximum number of statistics hour groups to capture

lives-kept

Maximum number of history lives to collect

life-size-value

Life size value (default 0)
Command Mode
  • /exec/configure/ip-sla/dns /exec/configure/ip-sla/fabricPathEcho

history

{ no | default } history { { distributions-of-statistics-kept } | { enhanced [ interval [ <interval-seconds> [ buckets [ <num-buckets> ] ] ] ] } | { hours-of-statistics-kept } | { statistics-distribution-interval } }

Syntax Description

Syntax Description

no

interval

(Optional) buckets

distributions-of-statistics-kept

hours-of-statistics-kept

statistics-distribution-interval

default

Set a command to its defaults

history

History and Distribution Data

enhanced

Enable enhanced history collection

interval-seconds

(Optional) Interval in seconds

buckets

(Optional) Number of buckets to collect data

num-buckets

(Optional) Number of buckets

hours-of-statistics-kept

Maximum number of statistics hour groups to capture
Command Mode
  • /exec/configure/ip-sla/jitter

history

history { { distributions-of-statistics-kept <num-dist-stats> } | { enhanced [ interval [ <interval-seconds> [ buckets [ <num-buckets> ] ] ] ] } | { hours-of-statistics-kept <num-hours-of-stats> } | { statistics-distribution-interval <dist-interval> } }

Syntax Description

Syntax Description

interval

(Optional) buckets

num-buckets

(Optional) <num-hours-of-stats>

enhanced

hours-of-statistics-kept

history

History and Distribution Data

distributions-of-statistics-kept

Maximum number of statistics distribution buckets to capture

num-dist-stats

Distribution bucket size value (default 1)

interval-seconds

(Optional) Interval in seconds

buckets

(Optional) Number of buckets to collect data

hours-of-statistics-kept

Maximum number of statistics hour groups to capture

num-hours-of-stats

Hour groups size value (default 2)

statistics-distribution-interval

Statistics distribution interval size

dist-interval

Distribution interval value in msec (default 20)
Command Mode
  • /exec/configure/ip-sla/jitter

history buffer

[no] history buffer [ { size [ <onep-historysize> [ purge <historypurge> ] ] } | { purge <historypurge> [ size <onep-historysize> ] } | { session [ <appname-str> ] } ]

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

history

One Platform history trails

buffer

In memory buffering of API history trails

session

(Optional) Session history filter

appname-str

(Optional) Full or partial session name

size

(Optional) History buffer size in bytes

onep-historysize

(Optional) Bytes (default: 32768)

purge

(Optional) Purge the oldest or newest session history

historypurge

(Optional) Purge session history
Command Mode
  • /exec/configure/onep

history syslog

[no] history syslog

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

history

One Platform history trails

syslog

Enable the API history trails to syslog
Command Mode
  • /exec/configure/onep

hold adjacency

hold adjacency <all>

Syntax Description

Syntax Description

hold

Hold

adjacency

Display adjacency table

all

Hold all adjcencies
Command Mode
  • /exec

hold ip route

hold ip { route | rnh } [ vrf { <vrf-name> | <vrf-known-name> | <vrf-all> } ] <all>

Syntax Description

Syntax Description

hold

Hold

ip

IPv4

route

Hold routing information

rnh

Hold only RNH information

vrf

(Optional) VRF

vrf-name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

vrf-all

(Optional) Display information for all VRFs

all

Hold all routes
Command Mode
  • /exec

hold ipv6 route

hold ipv6 route [ vrf { <vrf-name> | <vrf-known-name> | <vrf-all> } ] <all>

Syntax Description

Syntax Description

hold

Hold

ipv6

IPv6

route

Hold routing information

vrf

(Optional) VRF

vrf-name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name

vrf-all

(Optional) Display information for all VRFs

all

Hold all routes
Command Mode
  • /exec

hold timeout

hold timeout <timeout_val>

Syntax Description

Syntax Description

hold

Hold timer

timeout

timer timeout

timeout_val

timeout duration in seconds
Command Mode
  • /exec/configure/vpc-domain

holdtime

holdtime { infinite | <secs> } | no holdtime

Syntax Description

Syntax Description

no

Negate a command or set its defaults

holdtime

LDP session holdtime

infinite

Ignore LDP session holdtime

secs

Holdtime in seconds
Command Mode
  • /exec/configure/ldp

hop

{ hop <val> } | { no hop }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

hop

Configure ngoam hop count

val

Configure ngoam service hop count value
Command Mode
  • /exec/configure/configngoamprofile

host-reachability protocol

[no] host-reachability protocol [ bgp | openflow | openflow-ir ]

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

host-reachability

Configure host reachability advertisement

protocol

Control protocol to use

bgp

(Optional) Border Gateway Protocol

openflow

(Optional) OpenFlow

openflow-ir

(Optional) OpenFlow-IR
Command Mode
  • /exec/configure/if-nve

host-reachability protocol controller

[no] host-reachability protocol controller <controller-id>

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

host-reachability

Configure host reachability advertisement

protocol

Control protocol to use

controller

Controller

controller-id

Controller id value
Command Mode
  • /exec/configure/if-nve

hostname

{ hostname | switchname } <name> | no { hostname | switchname }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

hostname

Configure system's host name

switchname

Configure system's host name

name

Enter switchname
Command Mode
  • /exec/configure

hostname dynamic

[no] hostname dynamic

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hostname

Set dynamic hostname for IS-IS

dynamic

Dynamic hostname
Command Mode
  • /exec/configure/otv-isis/otv-isis-vrf-common

hostname dynamic

[no] hostname dynamic

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hostname

Set dynamic hostname for IS-IS

dynamic

Dynamic hostname
Command Mode
  • /exec/configure/router-isis/router-isis-vrf-common

hsrp

[no] hsrp <group-id> [ ipv4 ]

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hsrp

HSRP interface configuration commands

group-id

Group number (0-255 for HSRPv1)

ipv4

(Optional) Configure IP Version 4 group
Command Mode
  • /exec/configure/if-eth-any /exec/configure/if-vlan-common /exec/configure/if-port-channel /exec/configure/if-sub /exec/configure/if-ethernet-all

hsrp anycast

[no] hsrp anycast <id> { ipv4 | ipv6 | both }

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hsrp

HSRP configuration commands

anycast

Anycast related commands

id

Bundle number

ipv4

Associate IP Version 4 for the bundle

ipv6

Associate IP Version 6 for the bundle

both

Associate IP Version 4 and 6 for the bundle
Command Mode
  • /exec/configure

hsrp bfd

[no] hsrp bfd

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hsrp

HSRP interface configuration commands

bfd

BFD protocol
Command Mode
  • /exec/configure/if-eth-any /exec/configure/if-vlan-common /exec/configure/if-port-channel /exec/configure/if-sub /exec/configure/if-ethernet-all

hsrp bfd all-interfaces

[no] hsrp bfd all-interfaces

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hsrp

HSRP interface configuration commands

bfd

BFD protocol

all-interfaces

On all interfaces
Command Mode
  • /exec/configure

hsrp delay minimum

hsrp delay { minimum <min-delay> | reload <reload-delay> } + | no hsrp delay [ minimum | reload ]

Syntax Description

Syntax Description

no

Negate a command or set its defaults

hsrp

HSRP interface configuration commands

delay

HSRP initialisation delay

minimum

Minimum delay

reload

Delay after reload

min-delay

<0-10000> Delay in seconds

reload-delay

<0-10000> Delay in seconds

minimum

(Optional) reload
Command Mode
  • /exec/configure/if-eth-any /exec/configure/if-vlan-common /exec/configure/if-port-channel /exec/configure/if-sub /exec/configure/if-ethernet-all

hsrp force state vlan

hsrp force state vlan { <vlans> | all }

Syntax Description

Syntax Description

hsrp

Hot Standby Router Protocol (HSRP) information

force

Move the HSRP state

state

HSRP state

vlan

HSRP state changes for these vlans

all

Include all HSRP configured VLANs

vlans

VLAN IDs of the VLAN for which state change will affect
Command Mode
  • /exec

hsrp internal

[no] hsrp internal [ debug-level <level> ]

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hsrp

HSRP commands

internal

HSRP internal information

debug-level

(Optional) enable debug level

level

(Optional) trace level
Command Mode
  • /exec

hsrp internal

[no] hsrp internal [ sequence-number ] [ [ command <id> ] ] [ <data1> ] [ <data2> ] [ <data3> ]

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hsrp

HSRP commands

internal

enable HSRP internals

sequence-number

(Optional) enable the sequence number transmit in Hellos

command

(Optional) Internal command specified through number

id

(Optional) Internal command value

data1

(Optional) Internal data1

data2

(Optional) Internal data2

data3

(Optional) Internal data3
Command Mode
  • /exec

hsrp ipv6

[no] hsrp <group-id> ipv6

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hsrp

HSRP interface configuration commands

group-id

Group number

ipv6

Configure IP Version 6 group
Command Mode
  • /exec/configure/if-eth-any /exec/configure/if-vlan-common /exec/configure/if-port-channel /exec/configure/if-sub /exec/configure/if-ethernet-all

hsrp mac-refresh

hsrp mac-refresh [ <time> ] | no hsrp mac-refresh

Syntax Description

Syntax Description

no

Negate a command or set its defaults

hsrp

HSRP interface configuration commands

mac-refresh

Interface mac-refresh time

time

(Optional) Timeout value (0-10000) in sec
Command Mode
  • /exec/configure/if-eth-any /exec/configure/if-vlan-common /exec/configure/if-port-channel /exec/configure/if-sub /exec/configure/if-ethernet-all

hsrp timers extended-hold

[no] hsrp timers extended-hold [ <extended-hold> ]

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hsrp

HSRP interface configuration commands

timers

Global Timers

extended-hold

Extended Hold

extended-hold

(Optional) Time in seconds
Command Mode
  • /exec/configure

hsrp use-bia

[no] hsrp use-bia [ scope interface ]

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hsrp

HSRP interface configuration commands

use-bia

HSRP uses interface's burned in address

scope

(Optional) Specify the scope of use-bia

interface

(Optional) Use-bia applies to all groups on this interface or sub-interface
Command Mode
  • /exec/configure/if-eth-any /exec/configure/if-vlan-common /exec/configure/if-port-channel /exec/configure/if-sub /exec/configure/if-ethernet-all

hsrp version 1

hsrp version { 1 | 2 } | no hsrp version

Syntax Description

Syntax Description

no

Negate a command or set its defaults

hsrp

HSRP interface configuration commands

version

HSRP version

1

Version 1

2

Version 2
Command Mode
  • /exec/configure/if-eth-any /exec/configure/if-vlan-common /exec/configure/if-port-channel /exec/configure/if-sub /exec/configure/if-ethernet-all

human

| human

Syntax Description

Syntax Description

|

Pipe command output to filter

human

output in human format
Command Mode
  • /output

human

| human

Syntax Description

Syntax Description

|

Pipe command output to filter

human

output in human format
Command Mode
  • /output

hw-module logging onboard

[no] hw-module logging onboard [ { counter-stats | module <module> [ { counter-stats } ] } ]

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hw-module

Enable/Disable OBFL information

logging

Enable/Disable OBFL information

onboard

Enable/Disable OBFL information

counter-stats

(Optional) Enable/Disable OBFL counter statistics

module

(Optional) Enable/Disable OBFL information for Module

module

(Optional) Enter module number
Command Mode
  • /exec/configure

hw-module logging onboard

[no] hw-module logging onboard [ { environmental-history | error-stats | interrupt-stats | module <module> [ { environmental-history | error-stats | interrupt-stats | obfl-logs | cpuhog } ] | obfl-logs | cpuhog } ]

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

hw-module

Enable/Disable OBFL information

logging

Enable/Disable OBFL information

onboard

Enable/Disable OBFL information

environmental-history

(Optional) Enable/Disable OBFL environmental history

error-stats

(Optional) Enable/Disable OBFL error statistics

interrupt-stats

(Optional) Enable/Disable OBFL interrupt statistics

cpuhog

(Optional) Enable/Disable OBFL cpu hog events

module

(Optional) Enable/Disable OBFL information for Module

module

(Optional) Enter module number

obfl-logs

(Optional) Enable/Disable OBFL (boot-uptime/device-version/obfl-history)
Command Mode
  • /exec/configure