R Commands

This chapter describes the Cisco NX-OS Routing Information Protocol (RIP) commands that begin with R.

redistribute (RIP)

To redistribute routes from another routing domain into the Routing Information Protocol (RIP), use the redistribute command. To restore the system to its default condition in which the software does not redistribute routes, use the no form of this command.

redistribute {bgp id | direct | eigrp id | ospf id | static} route-map map-name

Syntax Description

bgp id

Redistributes routes from the Border Gateway Protocol (BGP). The ID is an autonomous system number. The range for 2-byte numbers is from 1 to 65535. The range for 4-byte numbers is from 1.0 to 65535.65535.

direct

Redistributes routes from directly connected routes only.

eigrp id

Redistributes routes from the Enhanced Interior Gateway Routing Protocol (EIGRP). The ID is an EIGRP instance name from which routes are to be redistributed. The value takes the form of a string. You can enter a decimal number, but Cisco Nexus 6000 stores it internally as a string.

ospf id

Redistributes routes from the Open Shortest Path First (OSPF) protocol. The ID is an OSPF instance name from which routes are to be redistributed. The value takes the form of a string. A decimal number can be entered, but it is stored internally as a string.

static

Redistributes routes from IP static routes.

route-map map-name

Associates a route map to set the redistribution policy for RIP.


Command Default

Route redistribution is disabled.

Command Modes

Router address-family configuration mode

Command History

Release
Modification

6.0(2)N1(1)

This command was introduced.


Usage Guidelines

Cisco Nexus 6000 filters redistributed routing information using a route map. You can configure the route map to set the RIP metric used for redistributed routes. If you do not set the RIP metric with a route map, Cisco Nexus 6000 determines the metric based on the redistributed protocol or by the default-metric command. If Cisco Nexus 6000 cannot determine a valid metric, then it does not redistribute the routes.

Examples

This example shows how to redistribute BGP routes into a RIP process: 

switch(config)# router rip Enterprise

switch(config-router)# address-family ipv4 unicast

switch(config-router-af)# redistribute bgp 64496

switch(config-router-af)# 

 
   
 
    
   
 Related Commands
 
   
 
    
 
      
      
      
 
        
        

          Command 
        
 		 
        
        

          Description 
        
 		 
      
 
      
 
       
 address-family 
 		 
       
 Enters address-family configuration mode. 
 		 
      
 
      
 
       
 default-information originate 
 		 
       
 Generates a default route for routes redistributed into RIP. 
 		 
      
 
      
 
       
 default-metric 
 		 
       
 Sets default metric values for routes redistributed from other protocols into RIP. 
 		 
      
 
      
 
       
 show ip rip 
 		 
       
 Displays a summary of RIP information for all RIP instances. 
 		 
      
 
      
    
 
   
 
   
 
   
 
 
     
    
    
   
 restart (RIP) 
 
    
   
 To restart a Routing Information Protocol (RIP) instance and remove all associated neighbors, use the restart command. 
 
    
   
restart eigrp instance-tag 
 
    
   
 Syntax Description
 
   
 
    
 
      
      
      
 
       
 instance-tag 
 		 
       
 Name for an RIP routing instance. The name can be a maximum of 20 alphanumeric characters. 
 		 
      
 
      
    
 
   
 
   
 
   
 
 
    
   
 Command Default 
 
    
   
 None 
 
    
   
 Command Modes 
 
    
   
 Global configuration mode 
 
    
   
 Command History
 
   
 
    
 
      
      
      
 
        
        

          Release 
        
 		 
        
        

          Modification 
        
 		 
      
 
      
 
       
 6.0(2)N1(1) 
 		 
       
 This command was introduced. 
 		 
      
 
      
    
 
   
 
   
 
   
 
 
    
   
 Usage Guidelines 
 
    
   
 This command requires the LAN Base Services license. 
 
    
   
 Examples 
 
    
   
 This example shows how to restart the RIP instance and remove all neighbors: 
 
    
   
 
    
switch(config)# restart rip Enterprise 

 
   
 
    
   
 
    
switch(config)#

 
   
 
    
   
 
    
 
   
 
    
   
 Related Commands
 
   
 
    
 
      
      
      
 
        
        

          Command 
        
 		 
        
        

          Description 
        
 		 
      
 
      
 
       
 copy running-config startup-config 
 		 
       
 Saves the configuration in the startup configuration file. 
 		 
      
 
      
 
       
 show ip eigrp interfaces 
 		 
       
 Displays information about EIGRP interfaces. 
 		 
      
 
      
    
 
   
 
   
 
   
 
 
    
     
    
    
   
 router rip 
 
    
   
 To configure the Routing Information Protocol (RIP) routing process, use the router rip command. To turn off the RIP routing process, use the no form of this command. 
 
    
   
router rip instance-tag 
 
    
   
no router rip 
 
    
   
 Syntax Description
 
   
 
    
 
      
      
      
 
       
 instance-tag 
 		 
       
 Name for this RIP instance. 
 		 
      
 
      
    
 
   
 
   
 
   
 
 
    
   
 Command Default 
 
    
   
 No RIP routing process is defined. 
 
    
   
 Command Modes 
 
    
   
 Global configuration mode 
 
    
   
 Command History
 
   
 
    
 
      
      
      
 
        
        

          Release 
        
 		 
        
        

          Modification 
        
 		 
      
 
      
 
       
 6.0(2)N1(1) 
 		 
       
 This command was introduced. 
 		 
      
 
      
    
 
   
 
   
 
   
 
 
    
   
 Examples 
 
    
   
 This example shows how to begin the RIP routing process: 
 
    
   
 
    
switch(config)# router rip Enterprise

 
   
 
    
   
 
    
 
   
 
    
   
 Related Commands
 
   
 
    
 
      
      
      
 
        
        

          Command 
        
 		 
        
        

          Description 
        
 		 
      
 
      
 
       
 ip router rip 
 		 
       
 Specifies a RIP instance for an interface.