Cisco Nexus 3548 Switch NX-OS Multicast Routing Configuration Guide, Release 9.3(x)

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Book Contents
Find Matches in This Book
Available Languages
Download Options

Book Title

Cisco Nexus 3548 Switch NX-OS Multicast Routing Configuration Guide, Release 9.3(x)

Chapter Title

Configuring Multicast Extranet

Results

Updated:
July 14, 2022

Chapter: Configuring Multicast Extranet

Configuring Multicast Extranet

This chapter describes how to configure Multicast Extranet on a Cisco NX-OS switch.

This chapter includes the following sections:

Information About Multicast Extranet

In the current NX-OS multicast implementation, multicast traffic can only flow within the same VRF. In the multicast extranet feature, multicast receivers may exist in different VRFs from source in an enterprise network.

With the multicast extranet, the RPF lookup for multicast route in receiver VRF can be done in source VRF, thereby allowing to return a valid RPF interface. This forms a source or RP tree from receiver VRF to source VRF, thus enabling the traffic originated from source VRF to be forwarded to OIFs in receiver VRF.

To support RPF selection in a different VRF, use the ip multicast rpf select vrf command.

Guidelines and Limitations for Multicast Extranet

Multicast Extranet has the following guidelines and limitations:

  • The source and RP should be in the same VRF.

  • Multicast NAT and multicast extranet should not coexist for the same group on the same box.

  • Auto RP is not supported on multicast extranet.

  • The number of multicast routes and VRFs required determine the memory consumption by multicast.

  • Multicast VPN (MVPN) extranet is not supported on multicast extranet.

  • The RPF lookup will be performed on the VRF specified by the ip multicast rpf select vrf command. Fallback mode is not supported.

  • For ASM multicast group translation in the fast-pass mode, the static OIF for untranslated groups must be configured on IGMPv2 interface. Source specific static OIF configuration (IGMPv3) is not supported.

Configuring Multicast Extranet

Before you begin

Before you begin, ensure that the PIM is enabled.

Procedure

  Command or Action Purpose

Step 1

configure terminal

Example:

switch# configure terminal
switch(config)#

Enters configuration mode.

Step 2

ip multicast rpf select vrf src-vrf-name group-list group-range

Example:

switch(config)# ip multicast rpf select vrf red group-list 224.1.1.0/24

Supports RPF selection in a different VRF. To disable the support, use the no form of this command.

vrf src-vrf-name is the source VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.

group-list group-range is the group range for the RPF select. The format is A.B.C.D/LEN with a maximum length of 32.

Step 3

(Optional) show ip mroute

Example:

switch(config)# show ip mroute
 (Optional)

Shows the running-configuration information for IPv4 multicast routes.

Step 4

(Optional) copy running-config startup-config

Example:

switch(config)# copy running-config startup-config
 (Optional)

Saves configuration changes.

Verifying the Multicast Extranet Configuration

To display the multicast extranet configuration information, perform one of the following tasks:

Table 1.

Command

Purpose

show ip mroute

Displays the running-configuration information for IPv4 multicast routes.

This example shows how to display information about running-configuration for IPv4 multicast routes:

switch(config)# show ip mroute
IP Multicast Routing Table for VRF "default"


(*, 225.1.1.207/32), uptime: 00:13:33, ip pim

Incoming interface: Vlan147, RPF nbr: 147.147.147.2, uptime: 00:13:33

Outgoing interface list: (count: 0)


Extranet receiver in vrf blue:

(*, 225.1.1.207/32) OIF count: 1


(40.1.1.2/32, 225.1.1.207/32), uptime: 00:00:06, mrib ip pim

Incoming interface: Vlan147, RPF nbr: 147.147.147.2, uptime: 00:00:06

Outgoing interface list: (count: 0)


Extranet receiver in vrf blue:

(40.1.1.2/32, 225.1.1.207/32) OIF count: 1


switch(config)#

For detailed information about the fields in the output from these commands, see the Cisco Nexus 3000 Series Multicast Routing Command Reference

Standards

Standards

Title

No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.

—

Was this Document Helpful?

FeedbackFeedback

Contact Cisco