Accessory Kits Contents

This appendix describes the contents of the Cisco Nexus 7000 Series accessory kits.

This appendix includes the following sections:

Cisco Nexus 7004 Switch Accessory Kit

This section describes the contents of the accessory kit that you can order for the Cisco Nexus 7004 switch. The accessory kit is shipped with each Cisco Nexus 7004 chassis. You use that kit for mounting the chassis on a four-post or two-post rack. Typically, you mount the front of the chassis using the front-mount brackets, which are already attached to the chassis, but if you need to mount the center of the chassis, you use the center-mount brackets (order part number N7K-C7004-RMK), which you must order separately. The kit also includes the screws, grounding lug, and other equipment that you use for all installations of this chassis.

Table C-1 lists and illustrates the contents for this kit.

.

Table C-1 Cisco Nexus 7004 Switch Accessory Kit Contents

Illustration
Description
Quantity

334724.jpg  

Chassis mounting screws

  • 12-24 x 3/4-in. Phillips screws
  • M6 x 19 mm Phillips screws

 

10

10

196530.jpg  

RJ-45 rollover cable

1

196531.jpg  

D B9F/RJ-45F PC terminal

1

185847.jpg  

Ground lug kit (includes the following parts):

  • Two-hole lug
  • M4 x 8-mm Phillips pan-head screws

1 kit

1 per kit

2 per kit

334652.jpg  

Cable ties, 8.5 inches

1 kit
(3 pieces)

113078.jpg  

ESD wrist strap (disposable)

1

Not applicable

Hazardous substances list for customers in China

1

Not applicable

Cisco Information Packet

1-Year Limited Warranty for Hardware

1

1

Not applicable

GR-1089 Installation and Caution Instructions

1
note.gif

Noteblank.gif If you do not receive a part listed in this document, contact Cisco Technical Support at this URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml.
If you purchased this product through a Cisco reseller, you might receive additional contents in your kit, such as documentation, hardware, and power cables.

The product shipment includes power cords for the following power supplies:

  • 3-kW AC power supplies—one power cord per power supply
  • 3-kW DC power supplies—no power cords supplied (you must supply a cable for 6 AWG and up to 45 A).

The shipped cables depend on your specification when placing a Cisco Nexus 7000 Series device order.

The available power cords for the 3-kW AC power supplies are as follows:

  • CAB-AC-16A-AUS—power cord, 250-VAC 16A, C19, Australia
  • CAB-AC16A-CH—power cord, 16-A, China
  • CAB-AC-2500W-EU—power cord, 250-VAC 16A, Europe
  • CAB-AC-2500W-INT—power cord, 250-VAC 16A, International
  • CAB-AC-2500W-ISRL—power cord, 250-VAC 16-A, Israel
  • CAB-9K16A-US1—power cord, 250-VAC 16A, Src Plug NEMA 6-20, US/Japan
  • CAB-AC-C6K-TWLK—power cord, 250-VAC 16A, twist lock, NEMA L6-20
  • CAB-7513AC—power cord, AC 110V North America
  • CAB-C19-CBN—cabinet jumper power cord, 250-VAC, 16A, C20C
  • CAB-ACS-16—power cord, 16-A, Switzerland
  • CAB-L520P-C19-US—NEMA L5-20 to IEC-C19 6ft US

The available AC power cords for the 3.5-kW HVAC/HVDC power supplies are as follows:

  • CAB-AC-16A-SG-AR—power cord, 250-VAC 16A, IRSM 2073Saf-D-Grid, Argentina
  • CAB-AC-16A-SG-AZ—power cord, 250-VAC 16A, AU20LS3/Saf-D-Grid, Australia and New Zealand
  • CAB-AC-16A-SG-BR—power cord, 250-VAC 16A, EL224/Saf-D-Grid, Brazil
  • CAB-AC-16A-SG-CH—power cord, 250-VAC 16A, GB 16C/Saf-D-Grid, China
  • CAB-AC-16A-SG-EU—power cord, 250-VAC 16A, CEE 7-7/Saf-D-Grid, Europe
  • CAB-AC-16A-SG-IN—power cord, 250-VAC 16A, IEC60309/Saf-D-Grid, International
  • CAB-AC-16A-SG-IND—power cord, 250-VAC 16A, SABS 164-1/Saf-D-Grid, India
  • CAB-AC-16A-SG-IS—power cord, 250-VAC 16A, SI 16S3/Saf-D-Grid, Israel
  • CAB-AC-16A-SG-IT—power cord, 250-VAC 16A, CEI 23-50/Saf-D-Grid to IEC-C19, Italy
  • CAB-AC-16A-SG-SA—power cord, 250-VAC 16A, EL/Saf-D-Grid, South Africa
  • CAB-AC-16A-SG-SK—power cord, 250-VAC 16A, Src/Saf-D-Grid, South Korea
  • CAB-AC-20A-SG-US—power cord, 110-VAC 20A, straight blade, NEMA 5-20P/Saf-D-Grid, North America
  • CAB-AC-20A-SG-US1—power cord, 125-VAC 20A, twist lock, NEMA L5-20/Saf-D-Grid, North America
  • CAB-AC-20A-SG-US2—power cord, 250-VAC 20A, straight-blade, NEMA 6-20/Saf-D-Grid
  • CAB-AC-20A-SG-US3—power cord, 250-VAC 20A, twist lock, NEMA L6-20/Saf-D-Grid
  • CAB-AC-20A-SG-US4—power cord, 277-VAC 20A, NEMA L7-20P/Saf-D-Grid, North America
  • CAB-AC-20A-SG-C20—cabinet jumper PDU power cord, 250-VAC, 20A, IEC C20/Saf-D-Grid, North America
  • CAB-AC-16A-SG-SW—power cord, 250-VAC 16A, SEV 5934-2/Saf-D-Grid, Switzerland
  • CAB-HV-25A-SG-US2—power cord, 300-VAC/500-VDC 20A, Ring Terminal/Saf-D-Grid, North America
  • CAB-HV-25A-SG-US5—power cord, 300-VAC 20A, Saf-D-Grid P-10/Saf-D-Grid P4, North America
  • CAB-HV-25A-SG-IN2—power cord, 300-VAC/500-VDC 20A, IEC/EU, Ring Terminal/Saf-D-Grid, International
  • CAB-HV-25A-SG-IN3—power cord, 300-VAC 20A, Saf-D-Grid P-10/Saf-D-Grid P4, IEC/EU, International
note.gif

Noteblank.gif All cables will not be orderable at first customer shipment (FCS).

The available DC power cords for the 3.5-kW HVAC/HVDC power supplies are as follows:

  • CAB-HV-25A-SG-US1—power cord, 400-VDC 20A, Saf-D-Grid/Saf-D-Grid, North America
  • CAB-HV-25A-SG-US2—power cord, 300-VAC/500-VDC 20A, Ring Terminal/Saf-D-Grid, North America
  • CAB-HV-25A-SG-IN1—power cord, 400-VDC 20A, IEC/EU, Saf-D-Grid/Saf-D-Grid, International
  • CAB-HV-25A-SG-IN2—power cord, 300-VAC/500-VDC 20A, IEC/EU, Ring Terminal/Saf-D-Grid, International
note.gif

Noteblank.gif All cables will not be orderable at first customer shipment (FCS).

Cisco Nexus 7009 Switch Accessory and Optional Kits

This section describes the contents of the Cisco Nexus 7009 accessory kits and the other kits that you can order for the Cisco Nexus 7009 switch. The accessory kit is shipped with each Cisco Nexus 7009 chassis. You use that kit for mounting the front of the chassis on a four-post or two-post rack. If you are centering the chassis on a two-post rack, you must also order the Cisco Nexus 7009 Center Mount Kit (part number N7K-C7009-CMK). If you need to another bottom support bracket for front-mounting the chassis, order the Cisco Nexus 7009 Bottom Support Kit (part number N7K-C7009-BSK). If you need an additional set of brackets for mounting the front of the chassis to a rack, order the Cisco Nexus 7009 Rack Mount Kit (part number N7K-C7009-RMK).

This section includes the following topics:

Cisco Nexus 7009 Accessory Kit

The Cisco Nexus 7009 Accessory Kit is shipped with each Cisco Nexus 7009 chassis. Table C-2 lists and illustrates the contents for this kit.

Table C-2 Cisco Nexus 7009 Switch Accessory Kit Contents

Illustration
Description
Quantity
330489.jpg

Front-mount Bottom-Support Kit (available separately as N7K-C7009-BSK) includes the following parts:

1 kit
  • Front-mount bottom support rails

2 per kit
  • Crossbar

1 per kit
  • 12-24 x 3/4-in. Phillips screws

20 per kit
  • M6 x 19-mm Phillips screws

20 per kit
  • M4 x 8-mm Phillips screws

2 per kit

Note : This accessory kit does not include the center-mount bottom-support kit (part number N7K-C7009-CMK). If you ordered that kit, it is included separately with the switch shipment.

 

196530.jpg  

RJ-45 rollover cable

1

196531.jpg  

D B9F/RJ-45F PC terminal

1

185847.jpg  

Ground lug kit (includes the following parts):

  • Two-hole lug
  • M4 x 8-mm Phillips pan-head screws

1 kit

1 per kit

2 per kit

330488.jpg  

Cable ties, 8.5 inches

1 kit
(7 pieces)

113078.jpg  

ESD wrist strap (disposable)

1

Not applicable

DCNM License for one Nexus 7000 Series chassis (optional)

1

Not applicable

Hazardous substances list for customers in China

1

Not applicable

Cisco Information Packet

1-Year Limited Warranty for Hardware

1

1

Not applicable

GR-1089 Installation and Caution Instructions

1
note.gif

Noteblank.gif If you do not receive a part listed in this document, contact Cisco Technical Support at this URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml.
If you purchased this product through a Cisco reseller, you might receive additional contents in your kit, such as documentation, hardware, and power cables.

If your Cisco Nexus 7000 Series system includes 6 kW power supply units, the product shipment includes one or two country-specific power cords for each of those power supply units. The shipped cables depend on your specification when placing a Cisco Nexus 7000 Series device order. The available power cords for the 6 kW power supplies are as follows:

  • CAB-AC-16A-AUS—power cord, 250-VAC 16A, C19, Australia
  • CAB-AC16A-CH—power cord, 16-A, China
  • CAB-AC-2500W-EU—power cord, 250-VAC 16A, Europe
  • CAB-AC-2500W-INT—power cord, 250-VAC 16A, International
  • CAB-AC-2500W-ISRL—power cord, 250-VAC 16-A, Israel
  • CAB-9K16A-US1—power cord, 250-VAC 16A, Src Plug NEMA 6-20, US/Japan
  • CAB-AC-C6K-TWLK—power cord, 250-VAC 16A, twist lock, NEMA L6-20
  • CAB-7513AC—power cord, AC 110V North America
  • CAB-C19-CBN—cabinet jumper power cord, 250-VAC, 16A, C20C
  • CAB-ACS-16—power cord, 16-A, Switzerland
  • CAB-L520P-C19-US—NEMA L5-20 to IEC-C19 6ft US

Cisco Nexus 7009 Center-Mount Kit

The Cisco Nexus 7009 Center-Mount Kit is not included in the Cisco Nexus 7009 accessory kit, but, if you are centering the Cisco Nuexus 7009 chassis on a two-post rack, you must order this kit (N7K-C7009-CMK) when you order the switch. Table C-3 lists the contents for this kit.

Table C-3 Cisco Nexus 7009 Center-Mount Kit (N7K-C7009-CMK)

Description
Quantity

Center-Mount Kit includes the following parts:

1 kit
  • Center-mount rack mounting brackets (right and left brackets)

2 per kit
  • Center-mount bottom support rails (right and left rails)

2 per kit
  • Crossbar

1 per kit
  • 12-24 x 3/4-in. Phillips screws

20 per kit
  • M6 x 19-mm Phillips screws

20 per kit
  • M4 x 8-mm screws

2 per kit

Cisco Nexus 7009 Bottom Support Kit

The Cisco Nexus 7009 Bottom Support Kit is included in the Cisco Nexus 7009 Accessory Kit for use in mounting the front of the chassis to a two-post or four-post rack. If you need to replace these parts, you can order this kit by using part number N7K-C7009-BSK. Table C-4 lists and illustrates the contents for this kit.

Table C-4 Cisco Nexus 7009 Bottom Support Kit (N7K-C7009-BSK)
Illustration
Description
Quantity
330489.jpg

Front-mount Bottom Support Kit includes the following parts:

1 kit
  • Front-mount bottom support rails (right and left rails)

2 per kit
  • Crossbar

1 per kit
  • 12-24 x 3/4-in. Phillips screws

20 per kit
  • M6 x 19-mm Phillips screws

20 per kit
  • M4 x 8-mm Phillips screws

2 per kit

Cisco Nexus 7009 Rack-Mount Kit

The Cisco Nexus 7009 switch ships with the front-mount rack mounting brackets assembled onto the chassis, but you can order the Cisco Nexus 7009 Rack-Mount Kit (order number N7K-C7009-RMK) if you need replacement parts. Table C-5 lists and illustrates the contents for this kit.

Table C-5 Cisco Nexus 7009 Rack-Mount Kit (N7K-C7009-RMK)
Description
Quantity

Rack-Mount Kit (available separately as N7K-C7009-RMK) includes the following parts:

1 kit
  • Front-mount rack mounting brackets (right and left brackets)

2 per kit
  • M4 x 6-mm Phillips screws

12 per kit

Cisco Nexus 7010 Switch Accessory Kits

Table C-6 lists and illustrates the accessory kit contents for the Cisco Nexus 7010 switch.

Table C-6 Cisco Nexus 7010 System Accessory Kit Contents

Illustration
Description
Quantity

195377.jpg  

Bottom support rails kit (includes the following parts):

  • 12-24 x 3/4-in. Phillips screws
  • M6 x 19-mm Phillips screws
  • Adjustable bottom support rails

1 kit

20 per kit

20 per kit

2 per kit

196530.jpg  

RJ-45 rollover cable

1

196531.jpg  

DB-9F/RJ-45F PC terminal

1

185847.jpg  

Ground lug kit (includes the following parts):

  • Two-hole lug
  • M4 x 8-mm Phillips pan-head screws

1 kit

1 per kit

2 per kit

186697.jpg  

Cable ties, 8.5 inches

1 kit
(10 pieces)

113078.jpg  

ESD wrist strap (disposable)

1

Not applicable

DCNM License for one Nexus 7000 Series chassis (optional)

1

Not applicable

Hazardous substances list for customers in China

1

Not applicable

Cisco Information Packet

1-Year Limited Warranty for Hardware

1

1

Not applicable

GR-1089 Installation and Caution Instructions

1
note.gif

Noteblank.gif If you do not receive a part listed in this document, contact Cisco Technical Support at this URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml.
If you purchased this product through a Cisco reseller, you might receive additional contents in your kit, such as documentation, hardware, and power cables.

If your Cisco Nexus 7000 Series system includes 6 kW power supply units, the product shipment includes one or two country-specific power cords for each of those power supply units. The shipped cables depend on your specification when placing a Cisco Nexus 7000 Series device order. The available power cords for the 6 kW power supplies are as follows:

  • CAB-AC-16A-AUS—power cord, 250-VAC 16A, C19, Australia
  • CAB-AC16A-CH—power cord, 16-A, China
  • CAB-AC-2500W-EU—power cord, 250-VAC 16A, Europe
  • CAB-AC-2500W-INT—power cord, 250-VAC 16A, International
  • CAB-AC-2500W-ISRL—power cord, 250-VAC 16-A, Israel
  • CAB-9K16A-US1—power cord, 250-VAC 16A, Src Plug NEMA 6-20, US/Japan
  • CAB-AC-C6K-TWLK—power cord, 250-VAC 16A, twist lock, NEMA L6-20
  • CAB-7513AC—power cord, AC 110V North America
  • CAB-C19-CBN—cabinet jumper power cord, 250-VAC, 16A, C20C
  • CAB-ACS-16—power cord, 16-A, Switzerland
  • CAB-L520P-C19-US—NEMA L5-20 to IEC-C19 6ft US

Cisco Nexus 7018 Switch Accessory Kits

Table C-7 lists and illustrates the accessory kit contents for the Cisco Nexus 7018 switch.

Table C-7 Cisco Nexus 7018 Switch Accessory Kit Contents

Illustration
Description
Quantity

186667.jpg  

Bottom support rails kit (includes the following parts):

  • 12-24 x 3/4-in. Phillips screws
  • M6 x 19-mm Phillips screws
  • Adjustable bottom support rails

1 kit

34 per kit

34 per kit

2 per kit

196530.jpg  

RJ-45 rollover cable

1

196531.jpg  

D B9F/RJ-45F PC terminal

1

185847.jpg  

Ground lug kit (includes the following parts):

  • Two-hole lug
  • M4 x 8-mm Phillips pan-head screws

1 kit

1 per kit

2 per kit

186697.jpg  

Cable ties, 8.5 inches

1 kit
(10 pieces)

113078.jpg  

ESD wrist strap (disposable)

1

Not applicable

DCNM License for one Nexus 7000 Series chassis (optional)

1

Not applicable

Hazardous substances list for customers in China

1

Not applicable

Cisco Information Packet

1-Year Limited Warranty for Hardware

1

1

Not applicable

GR-1089 Installation and Caution Instructions

1
note.gif

Noteblank.gif If you do not receive a part listed in this document, contact Cisco Technical Support at this URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml.
If you purchased this product through a Cisco reseller, you might receive additional contents in your kit, such as documentation, hardware, and power cables.

If your Cisco Nexus 7000 Series system includes 6 kW power supply units, the product shipment includes one or two country-specific power cords for each of those power supply units. The shipped cables depend on your specification when placing a Cisco Nexus 7000 Series device order. The available power cords for the 6 kW power supplies are as follows:

  • CAB-AC-16A-AUS—power cord, 250-VAC 16A, C19, Australia
  • CAB-AC16A-CH—power cord, 16-A, China
  • CAB-AC-2500W-EU—power cord, 250-VAC 16A, Europe
  • CAB-AC-2500W-INT—power cord, 250-VAC 16A, International
  • CAB-AC-2500W-ISRL—power cord, 250-VAC 16-A, Israel
  • CAB-9K16A-US1—power cord, 250-VAC 16A, Src Plug NEMA 6-20, US/Japan
  • CAB-AC-C6K-TWLK—power cord, 250-VAC 16A, twist lock, NEMA L6-20
  • CAB-7513AC—power cord, AC 110V North America
  • CAB-C19-CBN—cabinet jumper power cord, 250-VAC, 16A, C20C
  • CAB-ACS-16—power cord, 16-A, Switzerland
  • CAB-L520P-C19-US—NEMA L5-20 to IEC-C19 6ft US