Limitations and Compatible Characteristics of Ethernet Link Bundles
This list describes the properties and limitations of ethernet link bundles:
-
The router supports mixed speed bundles. Mixed speed bundles allow member links of different bandwidth to be configured as active members in a single bundle. The ratio of the bandwidth for bundle members must not exceed 10. Also, the total weight of the bundle must not exceed 64. For example, 100Gbps link and 10Gbps links can be active members in a bundle and load-balancing on member links is based on bandwidth weightage.
-
The weight of each bundle member is the ratio of its bandwidth to the lowest bandwidth member. Total weight of the bundle is the sum of weights or relative bandwidth of each bundle member. Since the weight for a bundle member is greater than or equal to 1 and less than or equal to 10, the total member of links in a bundle is less than 64 in mixed bundle case.
-
Any type of Ethernet interfaces can be bundled, with or without the use of LACP (Link Aggregation Control Protocol).
-
A single router can support a maximum of 63 bundle interfaces. Link bundles of only physical interfaces are supported.
-
A single router supports a maximum of 256 bundle interfaces and a default of 64 member links per bundle.
-
A single router supports up to a maximum of 1024 bundle sub-interfaces and up to a maximum of 64 member links per bundle.
-
If the HQoS profile is enabled, the maximum available trunks by default (physical+sub-interfaces) is 256. If more trunks are required, you can configure the hw-module profile qos max-trunks <256/512/1024> command.With HQoS enabled on bundle interfaces, a maximum of 4 priority levels are supported.
-
The available trunks by default is 256. If more trunks are required, you can configure the hw-module profile bundle-scale <256/512/1024> command. With HQoS enabled on bundle sub-interfaces, a maximum of 4 priority levels are supported.
-
The following limitations apply to the number of supported bundle members with HQoS profile:
-
Maximum of 1024 trunks (128 physical interfaces + 896 sub-interfaces) and 16 bundle members.
-
Maximum of 256 trunks (128 physical interfaces + 128 sub-interfaces) and 64 bundle members.
-
Maximum of 512 trunks (128 physical interfaces + 384 sub-interfaces) and 32 bundle members.
-
-
The following limitations apply to bundle sub-interfaces and the number of members per bundle:
-
Maximum of 1024 bundle sub-interfaces, each containing up to 16 member-links.
-
Maximum of 256 bundle sub-interfaces, each containing up to 64 member-links.
-
Maximum of 512 bundle sub-interfaces, each containing up to 32 member-links.
-
-
Physical layer and link layer configuration are performed on individual member links of a bundle.
-
Configuration of network layer protocols and higher layer applications is performed on the bundle itself.
-
IPv4 and IPv6 addressing is supported on ethernet link bundles.
-
A bundle can be administratively enabled or disabled.
-
Each individual link within a bundle can be administratively enabled or disabled.
-
Ethernet link bundles are created in the same way as Ethernet channels, where the user enters the same configuration on both end systems.
-
The MAC address that is set on the bundle becomes the MAC address of the links within that bundle.
-
Load balancing (the distribution of data between member links) is done by flow instead of by packet. Data is distributed to a link in proportion to the bandwidth of the link in relation to its bundle.
-
QoS is supported and is applied proportionally on each bundle member.
-
All links within a single bundle must terminate on the same two systems.
-
Bundled interfaces are point-to-point.
-
A link must be in the up state before it can be in distributing state in a bundle.
-
Only physical links can be bundle members.
-
Multicast traffic is load balanced over the members of a bundle. For a given flow, internal processes select the member link and all traffic for that flow is sent over that member.