Step 1
|
enable
|
Enables privileged EXEC mode.
|
Step 2
|
configure
terminal
Device# configure terminal
|
Enters global configuration mode.
|
Step 3
|
ip
sla
operation-number
Device(config)# ip sla 10
|
Begins configuration for an IP SLAs operation and enters IP SLA configuration mode.
|
Step 4
|
udp-jitter
{destination-ip-address |
destination-hostname }
destination-port
endpoint-list
endpoint-list [ssm]
[source-ip
ip-address ] [source-port
port-number ] [num-packets
number-of-packets ] [interval
interpacket-interval ]
Device(config-ip-sla)# udp-jitter 239.1.1.1 5000 endpoint-list mcast-rcvrs source-ip 10.10.10.106 source-port 7012 num-packets 50 interval 25
|
Configures the IP SLAs operation as a multicast UDP jitter operation and enters multicast UDP jitter configuration mode.
|
Step 5
|
control retry
retries
Device(config-ip-sla-multicast-jitter-oper)# control retry 2
|
(Optional) Configures the number of times a sending device will resend a control protocol message.
|
Step 6
|
control timeout
seconds
Device(config-ip-sla-multicast-jitter)# control timeout 4
|
(Optional) Configures the number of seconds that the destination device will wait for a control protocol message.
|
Step 7
|
dscp
dscp-value
Device(config-ip-sla-multicast-jitter-oper)# dscp 10
|
(Optional) Configures the DSCP value for the operation.
|
Step 8
|
tree-init
number
Device(config-ip-sla-multicast-jitter-oper)# tree-init 1
|
(Optional) Sets up the multicast tree.
|
Step 9
|
history
distributions-of-statistics-kept
size
Device(config-ip-sla-multicast-jitter-oper)# history distributions-of-statistics-kept 5
|
(Optional) Sets the number of statistics distributions kept per hop during an IP SLAs operation.
|
Step 10
|
history
enhanced
[interval
seconds ] [buckets
number-of-buckets ]
Device(config-ip-sla-multicast-jitter-oper)# history enhanced interval 900 buckets 100
|
(Optional) Enables enhanced history gathering for an IP SLAs operation.
|
Step 11
|
frequency
seconds
Device(config-ip-sla-multicast-jitter-oper)# frequency 30
|
(Optional) Sets the rate at which a specified IP SLAs operation repeats.
|
Step 12
|
history
hours-of-statistics-kept
hours
Device(config-ip-sla-multicast-jitter-oper)# history hours-of-statistics-kept 4
|
(Optional) Sets the number of hours for which statistics are maintained for an IP SLAs operation.
|
Step 13
|
owner
owner-id
Device(config-ip-sla-multicast-jitter-oper)# owner admin
|
(Optional) Configures the Simple Network Management Protocol (SNMP) owner of an IP SLAs operation.
|
Step 14
|
request-data-size
bytes
Device(config-ip-sla-multicast-jitter-oper)# request-data-size 64
|
(Optional) Sets the protocol data size in the payload of an IP SLAs operation's request packet.
|
Step 15
|
history
statistics-distribution-interval
milliseconds
Device(config-ip-sla-multicast-jitter-oper)# history statistics-distribution-interval 10
|
(Optional) Sets the time interval for each statistics distribution kept for an IP SLAs operation.
|
Step 16
|
tag
text
Device(config-ip-sla-multicast-jitter-oper)# tag TelnetPollServer1
|
(Optional) Creates a user-specified identifier for an IP SLAs operation.
|
Step 17
|
threshold
milliseconds
Device(config-ip-sla-multicast-jitter-oper)# threshold 10000
|
(Optional) Sets the upper threshold value for calculating network monitoring statistics created by an IP SLAs operation.
|
Step 18
|
timeout
milliseconds
Device(config-ip-sla-multicast-jitter-oper)# timeout 10000
|
(Optional) Sets the amount of time an IP SLAs operation waits for a response from its request packet.
|
Step 19
|
tos
number
Device(config-ip-sla-multicast-jitter-oper)# tos 160
|
(Optional) In an IPv4 network only, defines the ToS byte in the IPv4 header of an IP SLAs operation.
|
Step 20
|
verify-data
Device(config-ip-sla-multicast-jitter-oper)# verify-data
|
(Optional) Causes an IP SLAs operation to check each reply packet for data corruption.
|
Step 21
|
vrf
vrf-name
Device(config-ip-sla-multicast-jitter-oper)# vrf vpn-A
|
(Optional) Allows monitoring within Multiprotocol Label Switching (MPLS) VPNs using IP SLAs operations.
|
Step 22
|
end
Device(config-ip-sla-multicast-jitter-oper)# end
|
Returns to privileged EXEC mode.
|
Step 23
|
show
ip
sla
configuration
[operation-number ]
Device# show ip sla configuration 10
|
(Optional) Displays configuration values including all defaults for all IP SLAs operations or a specified operation.
|