This document provides a sample configuration for LAN emulation using the ATM router module (ARM).
ARM provides the Catalyst 8540 Multiservice Switch Router (MSR) and 8510 MSR with high-speed internetworking between the Layer 2 and Layer 3 network topologies. When ARM is installed, you no longer need to choose Layer 3 or ATM technology, as is frequently the case with enterprise and metropolitan area applications. Instead, you can have both Layer 3 and ATM technologies in the same multiservice ATM switch router chassis.
A Catalyst 8510 or 8540 MSR equipped with ARM functionality provides bridging and routing from Ethernet to ATM and from ATM to ATM.
ARM offers interoperability between the Layer 3 switching interface modules used in the Catalyst 8510 or 8540 CSR (Campus Switch Router) and the ATM port adapters and interface modules used in the Catalyst 8510 or 8540 MSR chassis. You can therefore combine Layer 3 and ATM port adapters and interface modules in a Catalyst 8510 or 8540 MSR chassis equipped with ARM. Refer to Major Differences Between Cisco Catalyst 8540 CSR and Cisco Catalyst 8540 MSR to learn more about the differences between Catalyst 8500 MSR and Catalyst 8500 CSR.
You can install up to two ARMs in the slots numbered from 0 to 3 and from 9 to 12 in the Catalyst 8510 or 8540 MSR chassis.
There are no specific requirements for this document.
LAN emulation using ARM was introduced on the Catalyst 8510 MSR in Cisco IOS® Software Release12.0(10)W5(18b) and on the Catalyst 8540 MSR in Cisco IOS Software Release12.0(4a)W5(11a).
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
ARM is based on Cisco express forwarding (CEF) and supports these features:
Open Shortest Path First (OSPF), Routing Information Protocol (RIP), RIP2, Interior Gateway Routing Protocol (IGRP), and Enhanced IGRP.
Internet Control Message Protocol (ICMP) Destination Unreachable and Redirect messages.
Load balancing up to two equal paths.
Integrated routing and bridging (IRB).
For more information on document conventions, refer to Cisco Technical Tips Conventions.
In this section, you are presented with the information to configure the features described in this document.
This document uses this network setup. There is an ARM card in slot 9.
This document uses these configurations:
Note: These configurations only show the commands relevant for LANE.
|Catalyst 5500 (Switch)|
set vlan 3 4/5 set vlan 2 4/4
|Catalyst 5500 (LANE Card)|
hostname ATM ! ! ! lane database ARM name elan2 server-atm-address 47.009181000000009021449C01.00E01E2EE861.02 name elan3 server-atm-address 47.009181000000009021449C01.00E01E2EE861.03 ! interface Ethernet0 ! interface ATM0 atm preferred phy B atm pvc 1 0 5 qsaal atm pvc 2 0 16 ilmi lane config auto-config-atm-address lane config database ARM ! interface ATM0.2 multipoint lane server-bus ethernet elan2 lane client ethernet 2 elan2 ! interface ATM0.3 multipoint lane server-bus ethernet elan3 lane client ethernet 3 elan3
hostname 7000a ! interface Loopback0 ip address 220.127.116.11 255.255.255.0 ! interface Ethernet0/3 ip address 18.104.22.168 255.255.255.0 ! router eigrp 1 network 22.214.171.124 network 126.96.36.199
hostname 7206B ! interface Loopback0 ip address 188.8.131.52 255.255.255.0 no ip directed-broadcast ! interface Ethernet6/0 ip address 184.108.40.206 255.255.255.0 no ip directed-broadcast ! router eigrp 1 network 220.127.116.11 network 18.104.22.168
|Catalyst 8540 MSR|
hostname C8540-MSR ! interface Loopback0 ip address 22.214.171.124 255.255.255.0 no ip directed-broadcast ! interface ATM9/0/0 no ip address no ip directed-broadcast ! interface ATM9/0/0.2 multipoint ip address 126.96.36.199 255.255.255.0 no ip directed-broadcast lane client ethernet elan2 ! interface ATM9/0/0.3 multipoint ip address 188.8.131.52 255.255.255.0 no ip directed-broadcast lane client ethernet elan3 ! router eigrp 1 network 184.108.40.206 network 220.127.116.11 network 18.104.22.168 no auto-summary
This section provides information that you can use to confirm that your configuration is working properly.
Issue these commands to test whether your network is operating properly:
show ip route
show ip cef
show lane le-arp interface atm card/subcard/port[.subinterface-number]
The next sample output is a result of entering these commands on the devices shown in the network diagram. This output shows that the network is operating properly. The ping goes from the ATM9/0/0.3 interface of the Catalyst 8540 MSR to the Ethernet0/3 interface of the Cisco 7000 Router.
C8540-MSR# ping 22.214.171.124 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 126.96.36.199, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
You can also test connectivity between the Catalyst 8540 MSR and the Cisco 7200 Router by pinging the Ethernet6/0 interface of the Cisco 7206 from the Catalyst 8540. This sample output shows that the ping is successful.
C8540-MSR# ping 188.8.131.52 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 184.108.40.206, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
Another way to test connectivity is by issuing the show ip route command. The Catalyst 8540 MSR has a route to the network behind the Cisco 7200 Router by the address 220.127.116.11—learned by IGRP—and has a route to the network behind the Cisco 7000 Router by the address 18.104.22.168—learned via IGRP as well.
C8540-MSR# show ip route D 22.214.171.124/16 [90/130816] via 126.96.36.199, 00:34:58, ATM9/0/0.3 172.16.0.0/24 is subnetted, 1 subnets 188.8.131.52/24 is subnetted, 1 subnets C 184.108.40.206 is directly connected, Loopback0 C 220.127.116.11 is directly connected, ATM9/0/0.2 D 18.104.22.168/16 [90/130816] via 22.214.171.124, 00:29:50, ATM9/0/0.2 126.96.36.199/24 is subnetted, 1 subnets C 188.8.131.52 is directly connected, ATM9/0/0.3 C8540-MSR# show ip cef 184.108.40.206/24 attached ATM9/0/0.2 220.127.116.11/32 receive 18.104.22.168/32 receive 22.214.171.124/32 126.96.36.199 ATM9/0/0.2 188.8.131.52/32 receive 184.108.40.206/24 attached ATM9/0/0.3 220.127.116.11/32 receive 18.104.22.168/32 receive 22.214.171.124/32 126.96.36.199 ATM9/0/0.3 188.8.131.52/32 receive 184.108.40.206/16 220.127.116.11 ATM9/0/0.3 18.104.22.168/16 22.214.171.124 ATM9/0/0.2 126.96.36.199/24 attached Loopback0 188.8.131.52/32 receive 184.108.40.206/32 receive 220.127.116.11/32 receive
To see the LANE ARP table for the subinterfaces on the Catalyst 8540, issue the show lane le-arp command.
C8540-MSR# show lane le-arp interface atm 9/0/0.2 Hardware Addr ATM Address VCD Interface 0030.7b1e.90a8 47.009181000000009021449C01.00E01E2EE860.02 878 ATM9/0/0.2 C8540-MSR# show lane le-arp interface atm 9/0/0.3 Hardware Addr ATM Address VCD Interface 0000.0c0d.fdcb 47.009181000000009021449C01.00E01E2EE860.03 876 ATM9/0/0.3
There is currently no specific troubleshooting information available for this configuration.
The Cisco Support Community is a forum for you to ask and answer questions, share suggestions, and collaborate with your peers.
Refer to Cisco Technical Tips Conventions for information on conventions used in this document.