Catalyst 6500 Series Switch and Cisco 7600 Series Router Firewall Services Module Command Reference, 3.2
join-failover-group -- kill
Downloads: This chapterpdf (PDF - 383.0KB) The complete bookPDF (PDF - 41.41MB) | Feedback

join-failover-group through kill Commands

Table Of Contents

join-failover-group through kill Commands

join-failover-group

kerberos-realm

key

keypair

kill


join-failover-group through kill Commands


join-failover-group

To assign a context to a failover group, use the join-failover-group command in context configuration mode. To restore the default setting, use the no form of this command.

join-failover-group group_num

no join-failover-group group_num

Syntax Description

group_num

Specifies the failover group number.


Defaults

Failover group 1.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Context configuration


Command History

Release
Modification

3.1(1)

This command was introduced.


Usage Guidelines

The admin context is always assigned to failover group 1. You can use the show context detail command to display the failover group and context association.

Before you can assign a context to a failover group, you must create the failover group with the failover group command in the system context. Enter this command on the unit where the context is in the active state. By default, unassigned contexts are members of failover group 1, so if the context had not been previously assigned to a failover group, you should enter this command on the unit that has failover group 1 in the active state.

You must remove all contexts from a failover group, using the no join-failover-group command, before you can remove a failover group from the system.

Examples

The following example assigns a context named ctx1 to failover group 2:

hostname(config)# context ctx1
hostname(config-context)# join-failover-group 2
hostname(config-context)# exit

Related Commands

Command
Description

context

Enters context configuration mode for the specified context.

failover group

Defines a failover group for Active/Active failover.

show context detail

Displays context detail information, including name, class, interfaces, failover group association, and configuration file URL.


kerberos-realm

To specify the realm name for this Kerberos server, use the kerberos-realm command in aaa-server host configuration mode. To remove the realm name, use the no form of this command:

kerberos-realm string

no kerberos-realm

Syntax Description

string

A case-sensitive, alphanumeric string, up to 64 characters long. Spaces are not permitted in the string.

Note Kerberos realms only use numbers and upper-case letters. Although the FWSM accepts lower-case letters in the string argument, it does not translate lower-case letters to upper-case letters. Be sure to use upper-case letters only.


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Aaa-server host configuration


Command History

Release
Modification

3.1(1)

Introduced in this release.


Usage Guidelines

This command is valid only for Kerberos servers.

The value of the string argument should match the output of the Microsoft Windows set USERDNSDOMAIN command when it is run on the Windows 2000 Active Directory server for the Kerberos realm. In the following example, EXAMPLE.COM is the Kerberos realm name:

C:\>set USERDNSDOMAIN
USERDNSDOMAIN=EXAMPLE.COM

The string argument must use numbers and upper-case letters only. The kerberos-realm command is case sensitive and the FWSM does not translate lower-case letters to upper-case letters.

Examples

The following sequence shows the kerberos-realm command used to set the Kerberos realm to "EXAMPLE.COM" in the context of configuring a AAA server host:

hostname(config)# aaa-server svrgrp1 protocol kerberos
hostname(config-aaa-server-group)# aaa-server svrgrp1 host 1.2.3.4
hostname(config-aaa-server-host)# timeout 9
hostname(config-aaa-server-host)# retry 7
hostname(config-aaa-server-host)# kerberos-realm EXAMPLE.COM
hostname(config-aaa-server-host)# exit

Related Commands

Command
Description

aaa-server host

Enter AAA server host configuration mode so that you can configure AAA server parameters that are host-specific.

clear configure aaa-server

Remove all AAA command statements from the configuration.

show running-config aaa-server

Displays AAA server statistics for all AAA servers, for a particular server group, for a particular server within a particular group, or for a particular protocol


key

To specify the server secret value used to authenticate the FWSM to the AAA server, use the key command in aaa-server host mode. Aaa-server host configuration mode is accessibile from aaa-server protocol configuration mode. To remove the key, use the no form of this command.

key key

no key

Syntax Description

key

An alphanumeric keyword, up to 127 characters long.


Defaults

No default behaviors or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Aaa-server host


Command History

Release
Modification

3.1(1)

This command was introduced.


Usage Guidelines

The key value is a case-sensitive, alphanumeric keyword of up to 127 characters that is the same value as the key on the TACACS+ server. Any characters entered past 127 are ignored. The key is used between the client and the server for encrypting data between them. The key must be the same on both the client and server systems.The key cannot contain spaces, but other special characters are allowed.

This command is valid only for RADIUS and TACACS+ servers.

The key parameter of the aaa-server command in earlier FWSM versions is automatically converted to the equivalent key command.

Examples

The following example configures a TACACS+ AAA server named "svrgrp1" on host "1.2.3.4", sets a timeout of 9 seconds, sets a retry-interval of 7 seconds, and configures the key as "myexclusivemumblekey".

hostname(config)# aaa-server svrgrp1 protocol tacacs+
hostname(config-aaa-server-group)# aaa-server svrgrp1 host 1.2.3.4
hostname(config-aaa-server-host)# timeout 9
hostname(config-aaa-server-host)# retry-interval 7
hostname(config-aaa-server-host)# key myexclusivemumblekey

Related Commands

Command
Description

aaa-server host

Enters AAA server host configuration mode so that you can configure AAA server parameters that are host-specific.

clear configure aaa-server

Removes all AAA command statements from the configuration.

show running-config aaa-server

Displays AAA server configuration.


keypair

To specify the key pair whose public key is to be certified, use the keypair command in crypto ca trustpoint configuration mode. To restore the default setting, use the no form of the command.

keypair name

no keypair

Syntax Description

name

Specifies the name of the key pair.


Defaults

The default setting is not to include the key pair.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Crypto ca trustpoint configuration


Command History

Release
Modification

3.1(1)

This command was introduced.


Examples

The following example enters crypto ca trustpoint configuration mode for trustpoint central, and specifies a key pair to be certified for trustpoint central:

hostname(config)# crypto ca trustpoint central
hostname(ca-trustpoint)# keypair exchange

Related Commands

Command
Description

crypto ca trustpoint

Enters trustpoint configuration mode.

crypto key generate dsa

Generates DSA keys.

crypto key generate rsa

Generates RSA keys.

default enrollment

Returns enrollment parameters to their defaults.


kill

To terminate a Telnet session, use the kill command in privileged EXEC mode.

kill telnet_id

Syntax Description

telnet_id

Specifies the Telnet session ID.


Defaults

No default behaviors or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

1.1(1)

This command was introduced.


Usage Guidelines

The kill command lets you terminate a Telnet session. Use the who command to see the Telnet session ID. When you kill a Telnet session, the FWSM lets any active commands terminate and then drops the connection without warning.

Examples

The following example shows how to terminate a Telnet session with the ID "2". First, the who command is entered to display the list of active Telnet sessions. Then the kill 2 command is entered to terminate the Telnet session with the ID "2".

hostname# who
2: From 10.10.54.0 

hostname# kill 2

Related Commands

Command
Description

telnet

Configures Telnet access to the FWSM.

who

Displays a list of active Telnet sessions.