Broadband Access Aggregation and DSL Configuration Guide, Cisco IOS XE Release 3S
PPP-Max-Payload and IWF PPPoE Tag Support
Downloads: This chapterpdf (PDF - 1.26MB) The complete bookPDF (PDF - 5.18MB) | The complete bookePub (ePub - 1.08MB) | Feedback

PPP-Max-Payload and IWF PPPoE Tag Support

PPP-Max-Payload and IWF PPPoE Tag Support

The PPP-Max-Payload and IWF PPPoE Tag Support feature enables the PPP over Ethernet (PPPoE) component to process the PPP-Max-Payload and Interworking Functionality (IWF) PPPoE tags in the PPPoE discovery frame:

  • The tag ppp-max-payload command allows PPPoE peers to negotiate PPP maximum receive units (MRUs) greater than 1492 octets if the underlying network supports a maximum transmission unit (MTU) size greater than 1500 octets.
  • The IWF PPPoE tag allows the Broadband Remote Access Server (BRAS) to distinguish the IWF PPPoE from the regular PPPoE sessions to overcome the per-MAC session limit put on the BRAS as a protection from denial of service (DOS) attacks sourced from the same MAC address.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Information About PPP-Max-Payload and IWF PPPoE Tag Support

Accommodating an MTU MRU Greater than 1492 in PPPoE

Per the RFC, "Accommodating an MTU/MRU Greater than 1492 in PPPoE," PPPoE peers can negotiate only MRUs with a maximum of 1492 octets so that the PPPoE header and PPP protocol ID can be inserted in the PPPoE session data packet. The maximum for an Ethernet payload is 1500 octets.

RFC 2516 defines a new tag to allow PPPoE peers to negotiate PPP MRU greater than 1492 if the underlying networks can support an Ethernet payload of greater than 1500 bytes. To enable processing of this new tag, a command has been defined in the Cisco IOS command-line interface as tag ppp-max-payload.The PPP-Max-Payload and IWF PPPoE Tag Support feature enhances the PPPoE component so the tag ppp-max-payloadcommand can process the new tag to influence the Link Control Protocol (LCP) MRU negotiations for the PPP session based on the MRU value specified in the tag from the PPPoE client.

Interworking Functionality

The DSL Forum defined IWF to define the process for conversion of PPP over ATM (PPPoA) sessions to PPPoE sessions at the digital subscriber line access multiplexer (DSLAM) to the BRAS. This functionality was defined to help the migration of DSLAM networks from ATM to Ethernet media. So, essentially, the PPPoA session comes in to the DSLAM over ATM and is converted to a PPPoE session at the DSLAM, which is then connected to the BRAS as a PPPoE session. Each PPPoA session is mapped to a corresponding PPPoE session.

Typically, the BRAS is configured to limit PPPoE sessions originating from the same MAC address to protect itself from a DOS attack. This presents a problem for IWF PPPoE sessions because all PPPoE sessions originate from the same MAC address DSLAM. To overcome this issue, the IWF PPPoE tag is inserted at the DSLAM and read by the BRAS to distinguish the IWF PPPoE session from the regular PPPoE session during the PPPoE discovery frames.

For more information about this subject, refer to the DSL Forum Technical Report 101, "Migration to Ethernet-Based DSL Aggregation."

How to Configure PPP-Max-Payload and IWF PPPoE Tag Support

Enabling PPP-Max-Payload and IWF PPPoE Tag Support

To enable the PPP-Max-Payload and IWF PPPoE Tag Support feature, perform this task.

SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    bba-group pppoe {group-name | global}

    4.    virtual-template template-number

    5.    tag ppp-max-payload [minimum value maximum value] [deny]

    6.    sessions per-mac iwf limit per-mac-limit

    7.    interface {fastethernet | gigabitethernet | tengigabitethernet} slot /subslot/ port[subinterface]

    8.    pppoe enable [group group-name]

    9.    virtual-template template-number

    10.    ppp lcp echo mru verify [minimum value]

    11.    end

    12.    show pppoe session [all| packets]


DETAILED STEPS
     Command or ActionPurpose
    Step 1 enable


    Example:
    Router> enable
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.
     
    Step 2 configure terminal


    Example:
    Router# configure terminal
     

    Enters global configuration mode.

     
    Step 3 bba-group pppoe {group-name | global}


    Example:
    Router(config)# bba-group pppoe pppoe-group
     

    Enters BBA group configuration mode and defines a PPPoE profile.

     
    Step 4 virtual-template template-number


    Example:
    Router(config-bba-group)# virtual-template 1
     

    Configures a PPPoE profile with a virtual template to be used for cloning virtual access interfaces.

    • The template-number argument is an identifying number of the virtual template that will be used to clone virtual-access interfaces.
     
    Step 5 tag ppp-max-payload [minimum value maximum value] [deny]


    Example:
    Router(config-bba-group)# tag ppp-max-payload minimum 1200 maximum 3000
     

    Specifies a range for the ppp-max payload tag value that will be accepted by the BRAS.

    • Default values are 1492 for the minimum and 1500 for the maximum.
    • The ppp-max-payload tag value accepted from the client cannot exceed the physical interface value for MTU minus 8.
     
    Step 6 sessions per-mac iwf limit per-mac-limit


    Example:
    Router(config-bba-group)# sessions per-mac iwf limit 200
     

    Specifies a limit for IWF-specific sessions per MAC address (separate from session limits that are not IWF-specific).

    • If this command is not entered, the normal MAC-address session limit is applied to IWF sessions.
    • The per-mac-limit argument specifies the allowable number of IWF sessions. The default is 100.
     
    Step 7 interface {fastethernet | gigabitethernet | tengigabitethernet} slot /subslot/ port[subinterface]


    Example:
    Router(config-bba-group)# interface gigabitethernet 0/0/0
     

    Enters interface configuration mode for a Gigabit Ethernet interface.

     
    Step 8 pppoe enable [group group-name]


    Example:
    Router(config-if)# pppoe enable group 1
     

    Enables PPPoE sessions on an Ethernet interface or subinterface.

     
    Step 9 virtual-template template-number


    Example:
    Router(config-if)# virtual-template 1
     

    Configures a PPPoE profile with a virtual template to be used for cloning virtual access interfaces.

    • The template-number argument is an identifying number of the virtual template that will be used to clone virtual-access interfaces.
     
    Step 10 ppp lcp echo mru verify [minimum value]


    Example:
    Router(config-if)# ppp lcp echo mru verify minimum 1304
     

    Verifies the negotiated MRU and adjusts the PPP virtual access interface MTU for troubleshooting purposes.

    • If the optional minimum keyword is entered, the value can be from 64 to 1500.
    • If the verification of minimum MTU succeeds, the PPP connection’s interface MTU is set to that value. This reset is useful when you troubleshoot and need to adjust the sessions according to underlying physical network capability. After this command is configured, IP Control Protocol (IPCP) is delayed until verification of the MTU is completed at the LCP.
     
    Step 11 end


    Example:
    Router(config-if)# end
     

    Exits the current configuration mode and returns to privileged EXEC mode.

     
    Step 12 show pppoe session [all| packets]


    Example:
    Router# show pppoe session all
     

    Verifies the configuration and displays session information.

    • all --Displays output indicating if a session is IWF-specific or if the PPP-Max-Payload tag is in the discovery frame and accepted.
    • packets --Displays packet statistics for the PPPoE session.
     

    Disabling PPP-Max-Payload and IWF PPPoE Tag Support

    The tag ppp-max-payload command adjusts PPP MTU of the PPPoE session above the default maximum limit of 1492 bytes. But MTU values greater than 1492 can only be supported (with PPPoE) if the underlying Ethernet network supports these larger frames. Not all Ethernet networks support higher values. If your network does not support values higher than the default maximum, you should disable the PPP-Max-Payload and IWF PPPoE Tag Support feature by performing this task.

    SUMMARY STEPS

      1.    enable

      2.    configure terminal

      3.    bba-group pppoe {group-name | global}

      4.    tag ppp-max-payload deny


    DETAILED STEPS
       Command or ActionPurpose
      Step 1 enable


      Example:
      Router> enable
       

      Enables privileged EXEC mode.

      • Enter your password if prompted.
       
      Step 2 configure terminal


      Example:
      Router# configure terminal
       

      Enters interface configuration mode.

       
      Step 3 bba-group pppoe {group-name | global}


      Example:
      Router(config-if)# bba-group pppoe pppoe-group
       

      Enters BBA group configuration mode and defines a PPPoE profile.

       
      Step 4 tag ppp-max-payload deny


      Example:
      Router(config-bba-group)# tag ppp-max-payload deny
       

      Disables the processing of the ppp-max-payload tag value higher than the default of 1492 bytes.

       

      Configuration Examples for PPP-Max Payload and IWF PPPoE Tag Support

      This section provides a sample configuration showing the PPP-Max-Payload and IWF PPPoE Tag Support feature enabled and a configuration in which the effects of this feature are disabled:

      PPP-Max-Payload and IWF PPPoE Tag Support Enabled Example

      The following configuration example shows the PPP-Max-Payload and IWF PPPoE Tag Support enabled to accept PPP-Max-Payload tag values from 1492 to 1892, limits the number of sessions per MAC address to 2000 when the IWF is present, and verifies that the PPP session can accept 1500-byte packets in both directions:

      bba-group pppoe global
       virtual-template 1
       tag ppp-max-payload minimum 1492 maximum 1892
       sessions per-mac limit 1
       sessions per-mac iwf limit 2000
       ppp lcp echo mru verify
      !
       interface Virtual-Template 1
      !

      PPP-Max-Payload and IWF PPPoE Tag Support Disabled Example

      The following configuration example disables the effect of the tag ppp-max-payload command:

      bba-group pppoe global
       virtual-template 1
       tag ppp-max-payload deny

      Additional References

      The following sections provide references related to the PPP-Max-Payload and IWF PPPoE Tag Support feature.

      Related Documents

      Related Topic

      Document Title

      Additional information about commands used in this document

      Standards

      Standard

      Title

      DSL Forum Technical Report 101

      Migration to Ethernet-Based DSL Aggregation

      MIBs

      MIB

      MIBs Link

      No new or modified MIBs are supported by this feature, and support for existing MIBs has not been modified by this feature.

      To locate and download MIBs for selected platforms, Cisco IOS XE releases, and feature sets, use Cisco MIB Locator found at the following URL:

      http:/​/​www.cisco.com/​go/​mibs

      Technical Assistance

      Description

      Link

      The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

      To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

      Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

      http:/​/​www.cisco.com/​techsupport

      Feature Information for PPP-Max-Payload and IWF PPPoE Tag Support

      The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

      Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

      Table 1 Feature Information for PPP-Max-Payload and IWF PPPoE Tag Support

      Feature Name

      Releases

      Feature Information

      PPP-Max Payload and IWF PPPoE Tag Support

      Cisco IOS XE Release 2.3

      This feature was introduced on Cisco ASR 1000 Series Routers.

      This feature enables the PPP over Ethernet (PPPoE) component to process the PPP-Max-Payload and Interworking Functionality (IWF) PPPoE tags in the PPPoE discovery frame.

      The following commands were introduced or modified: ppp lcp echo mru verify, sessions per-mac iwf limit, show pppoe session, tag ppp-max-payload.