Cisco VPN Client para VPN 3000 Concentrator com autenticação SDI IPSec (Server versão 3.3)
Contents
Introduction
O Cisco VPN 3000 Concentrator pode ser configurado para autenticar Cisco VPN Clients por meio de um servidor Security Dynamics International (SDI). O VPN 3000 Concentrator atua como um cliente SDI, comunicando-se com o servidor SDI na porta 5500 do User Datagram Protocol (UDP). O documento a seguir mostra como garantir que o servidor SDI, o VPN 3000 Concentrator e o Cisco VPN Client estejam funcionando corretamente e como combinar os componentes. Se o VPN 3000 Concentrator ainda não tiver sido configurado, use as etapas de Instalar e Configurar o VPN 3000 Concentrator Sem SDI usando a interface de linha de comando (CLI) para a instalação e configuração iniciais. Se seu VPN 3000 Concentrator foi configurado anteriormente, siga as etapas para Modificar a configuração existente (Sem SDI).
Prerequisites
Requirements
Não existem requisitos específicos para este documento.
Componentes Utilizados
Esta configuração foi desenvolvida e testada utilizando as versões de software e hardware abaixo.
-
Servidor SDI 3.3 (UNIX e NT)
-
Concentrador VPN 3000 (2.5.2)
-
VPN Client 2.5.2.A
As informações neste documento foram criadas a partir de dispositivos em um ambiente de laboratório específico. All of the devices used in this document started with a cleared (default) configuration. Se você estiver trabalhando em uma rede ativa, certifique-se de que entende o impacto potencial de qualquer comando antes de utilizá-lo.
Conventions
Consulte as Convenções de Dicas Técnicas da Cisco para obter mais informações sobre convenções de documentos.
Informações de Apoio
Este documento se aplica ao Cisco VPN 3000 Client (2.5.x) ou ao Cisco VPN Client (3.x). Com a versão 3.0 e posterior, é possível agora configurar servidores SDI individuais para grupos individuais ao contrário de um servidor SDI definido globalmente e usado por todos os grupos. Os grupos que não têm servidores SDI individuais configurados usarão o servidor SDI definido globalmente.
Há três tipos de modos novos de número de identificação pessoal (PIN) no SDI. O VPN 3000 concentrator suporta as primeiras duas opções conforme mostrado abaixo.
-
O usuário seleciona um novo PIN.
-
O servidor escolhe um novo PIN e informa os usuários.
-
O servidor escolhe um novo PIN e informa os usuários; os usuários podem alterar o PIN.
Configurar
Nesta seção, você encontrará informações para configurar os recursos descritos neste documento.
Observação: para encontrar informações adicionais sobre os comandos usados neste documento, use a ferramenta Command Lookup Tool (somente clientes registrados).
Diagrama de Rede
Este documento utiliza a instalação de rede mostrada no diagrama abaixo.
Configurações
Instalar e configurar o concentrador VPN 3000 sem SADI
Configuramos o VPN 3000 Concentrator para autenticar localmente um usuário em um grupo; ao fazer isso antes de adicionar o SDI, podemos determinar que o IPSec entre o Cisco VPN Client e o VPN 3000 Concentrator está funcionando. Limpamos a configuração do Concentrador VPN 3000 na porta do console, em Administration (Administração) > System Reboot (Reinicialização do Sistema) > Schedule reboot (Programar reinicialização) > Reboot with Factory/Default Configuration (Reinicializar com Configuração de Fábrica/Padrão.
Após a reinicialização, foi feita a seguinte configuração inicial:
| Configuração do Concentrador VPN 3000 Concentrator |
|---|
Login: admin
Password:
Welcome to
Cisco Systems
VPN 3000 Concentrator Series
Command Line Interface
Copyright (C) 1998-2000 Cisco Systems, Inc.
-- : Set the time on your device. The correct time is very important,
-- : so that logging and accounting entries are accurate.
-- : Enter the system time in the following format:
-- : HH:MM:SS. Example 21:30:00 for 9:30 PM
> Time
Quick -> [ 13:02:39 ]
-- : Enter the date in the following format.
-- : MM/DD/YYYY Example 06/12/1999 for June 12th 1999.
> Date
Quick -> [ 10/09/2000 ]
-- : Set the time zone on your device. The correct time zone is very
-- : important so that logging and accounting entries are accurate.
-- : Enter the time zone using the hour offset from GMT:
-- : -12 : Kwajalein -11 : Samoa -10 : Hawaii -9 : Alaska
-- : -8 : PST -7 : MST -6 : CST -5 : EST
-- : -4 : Atlantic -3 : Brasilia -2 : Mid-Atlantic -1 : Azores
-- : 0 : GMT +1 : Paris +2 : Cairo +3 : Kuwait
-- : +4 : Abu Dhabi +5 : Karachi +6 : Almaty +7 : Bangkok
-- : +8 : Singapore +9 : Tokyo +10 : Sydney +11 : Solomon Is.
-- : +12 : Marshall Is.
> Time Zone
Quick -> [ -5 ] -5
1) Enable DST Support
2) Disable DST Support
Quick -> [ 1 ]
This table shows current IP addresses.
Interface IP Address/Subnet Mask MAC Address
-------------------------------------------------------------------------------
| Ethernet 1 - Private | 0.0.0.0/0.0.0.0 |
| Ethernet 2 - Public | 0.0.0.0/0.0.0.0 |
| Ethernet 3 - External | 0.0.0.0/0.0.0.0 |
-------------------------------------------------------------------------------
** An address is required for the private interface. **
> Enter IP Address
Quick Ethernet 1 -> [ 0.0.0.0 ] 10.31.1.59
Waiting for Network Initialization...
> Enter Subnet Mask
Quick Ethernet 1 -> [ 255.0.0.0 ] 255.255.255.0
1) Ethernet Speed 10 Mbps
2) Ethernet Speed 100 Mbps
3) Ethernet Speed 10/100 Mbps Auto Detect
Quick Ethernet 1 -> [ 3 ]
1) Enter Duplex - Half/Full/Auto
2) Enter Duplex - Full Duplex
3) Enter Duplex - Half Duplex
Quick Ethernet 1 -> [ 1 ]
1) Modify Ethernet 1 IP Address (Private)
2) Modify Ethernet 2 IP Address (Public)
3) Modify Ethernet 3 IP Address (External)
4) Configure Expansion Cards
5) Save changes to Config file
6) Continue
7) Exit
Quick -> 2
This table shows current IP addresses.
Interface IP Address/Subnet Mask MAC Address
-------------------------------------------------------------------------------
| Ethernet 1 - Private | 10.31.1.59/255.255.255.0 | 00.90.A4.00.1C.B4
| Ethernet 2 - Public | 0.0.0.0/0.0.0.0 |
| Ethernet 3 - External | 0.0.0.0/0.0.0.0 |
-------------------------------------------------------------------------------
> Enter IP Address
Quick Ethernet 2 -> [ 0.0.0.0 ] 172.18.124.134
> Enter Subnet Mask
Quick Ethernet 2 -> [ 255.255.0.0 ] 255.255.255.0
1) Ethernet Speed 10 Mbps
2) Ethernet Speed 100 Mbps
3) Ethernet Speed 10/100 Mbps Auto Detect
Quick Ethernet 2 -> [ 3 ]
1) Enter Duplex - Half/Full/Auto
2) Enter Duplex - Full Duplex
3) Enter Duplex - Half Duplex
Quick Ethernet 2 -> [ 1 ]
1) Modify Ethernet 1 IP Address (Private)
2) Modify Ethernet 2 IP Address (Public)
3) Modify Ethernet 3 IP Address (External)
4) Configure Expansion Cards
5) Save changes to Config file
6) Continue
7) Exit
Quick -> 6
-- : Assign a system name to this device.
> System Name
Quick -> vpn3000
-- : Specify a local DNS server, which lets you enter hostnames
-- : rather than IP addresses while configuring.
> DNS Server
Quick -> [ 0.0.0.0 ]
-- : Enter your Internet domain name; e.g., yourcompany.com
> Domain
Quick ->
> Default Gateway
Quick -> 172.18.124.1
-- : Configure protocols and encryption options.
-- : This table shows current protocol settings
PPTP | L2TP |
---------------------------------------------
| Enabled | Enabled |
| No Encryption Req | No Encryption Req |
---------------------------------------------
1) Enable PPTP
2) Disable PPTP
Quick -> [ 1 ]
1) PPTP Encryption Required
2) No Encryption Required
Quick -> [ 2 ]
1) Enable L2TP
2) Disable L2TP
Quick -> [ 1 ]
1) L2TP Encryption Required
2) No Encryption Required
Quick -> [ 2 ]
1) Enable IPSec
2) Disable IPSec
Quick -> [ 1 ]
-- : Configure address assignment for PPTP, L2TP and IPSec.
1) Enable Client Specified Address Assignment
2) Disable Client Specified Address Assignment
Quick -> [ 2 ]
1) Enable Per User Address Assignment
2) Disable Per User Address Assignment
Quick -> [ 2 ]
1) Enable DHCP Address Assignment
2) Disable DHCP Address Assignment
Quick -> [ 2 ]
1) Enable Configured Pool Address Assignment
2) Disable Configured Pool Address Assignment
Quick -> [ 2 ] 1
> Configured Pool Range Start Address
Quick -> 192.168.1.1
> Configured Pool Range End Address
Quick -> [ 0.0.0.0 ] 192.168.1.100
-- : Specify how to authenticate users
1) Internal Authentication Server
2) RADIUS Authentication Server
3) NT Domain Authentication Server
4) SDI Authentication Server
5) Continue
Quick -> [ 1 ] 1
Current Users
-------------------------------------------------------------------------------
No Users
-------------------------------------------------------------------------------
1) Add a User
2) Delete a User
3) Continue
Quick -> 1
> User Name
Quick -> 37297304
> Password
Quick -> *********
Verify -> *********
Current Users
-------------------------------------------------------------------------------
| 1. 37297304 | |
-------------------------------------------------------------------------------
1) Add a User
2) Delete a User
3) Continue
Quick -> 3
> IPSec Group Name
Quick -> vpn3000
> IPSec Group Password
Quick -> ********
Verify -> ********
-- : We strongly recommend that you change the password for user admin.
> Reset Admin Password
Quick -> [ ***** ]
Verify ->
1) Goto Main Configuration Menu
2) Save changes to Config file
3) Exit
Quick -> 2
1) Goto Main Configuration Menu
2) Save changes to Config file
3) Exit
Quick -> 3
Done
|
Modificar a configuração existente (sem SDI)
Se o VPN 3000 Concentrator tiver sido configurado previamente, as seguintes telas serão utilizadas para verificar as configurações de grupo, usuário e IPSec/IKE:
-
Use essa tela para adicionar um grupo com autenticação local:
-
Utilize esta tela para incluir um usuário ao grupo com autenticação local:
-
Use a tela de proposta IPSec > IKE para adicionar configurações de IKE (as configurações mostradas são padrões do sistema):
Teste o Cisco VPN Client e o VPN 3000 Concentrator sem SDI
Após modificar a configuração existente no VPN 3000 Concentrator, instalamos o Cisco VPN Client e configuramos uma nova conexão para concluir em 172.18.124.134 (a interface pública de concentrador). Nossas informações de acesso ao grupo eram "vpn3000" (o nome do grupo) e a senha do grupo era a senha do grupo. Quando clicamos em Connect, o nome de usuário era "37297304" (nome do usuário) e a senha do usuário era a senha do usuário (armazenada localmente no VPN 3000 Concentrator; o SDI ainda não está envolvido). Veja Boa depuração de IPSec com autenticação local para a depuração de IKE, IKEDBG, IKEDECODE, IPSEC, IPSECDBG, IPSECDECODE.
Teste da operação do servidor SDI sem o VPN 3000 Concentrator
UNIX (Solaris)
-
No servidor SDI, crie uma conta sditest utilizando a ferramenta admintool do Solaris.
A entrada /etc/senha deve ter a seguinte aparência:
sditest:x:76:10::/local/0/sditest:/local/0/opt/ace/prog/sdshell
Observação: os valores e os caminhos para o diretório inicial do usuário e o "sdshell" dependem do sistema.
-
Atribua um token ao sditest.
-
Tente Telnet no host UNIX como sditest. O host solicita que você forneça uma senha UNIX e o PASSCODE. Após a autenticação, ele permite que você entre como sditest naquele host.
Microsoft Windows NT
-
Instale o SecurSight Agent.
-
Selecione Programs > SecurSight > Test Authentication.
Configure o SDI/User para se comunicar com o VPN 3000 Concentrator
Use as seguintes etapas para configurar SDI/User para se comunicar com o VPN 3000 Concentrator:
-
Na tela SDI Server Edit Token (Editar token do servidor SDI), verifique se o token está "Enabled" (Habilitado) e não no modo New PIN (Novo PIN).
-
Clique em Resynchronize Token e Set PIN to Next Tokencode.
-
Na tela Edit User, atribua um token ao usuário e certifique-se de que "Allowed to create a PIN" não esteja marcado.
-
Clique em Client Ativations (Ativações do cliente) e verifique se o VPN 3000 Concentrator está incluído.
Observação: o VPN 3000 Concentrator é considerado um cliente do servidor SDI; a tela abaixo é a tela Adicionar/editar cliente do servidor SDI. Como este é um novo cliente, a caixa "Sent Node Secret" está acinzentada. O servidor SDI não teve a oportunidade de enviar o arquivo "segredo do nó" ao concentrador (esse arquivo será exibido no concentrador na seção Administration > File Management > Files como "SECURID"). Depois de uma autenticação bem-sucedida do VPN 3000, o arquivo de segredo de nó é exibido no concentrador VPN 3000 e a caixa "Sent Node Secret" é marcada.
-
Clique em Ativações do usuário e verifique se o usuário está incluído.
Configure e Teste o VPN 3000 Concentrator para SDI
Siga as etapas a seguir para configurar e testar o VPN 3000 Concentrator para SDI.
-
Use a tela a seguir para configurar o VPN 3000 Concentrator para autenticar em SDI:
-
A partir do SDI, vá até Relatório > Monitor de registro > Monitor de atividade e clique em OK para observar as solicitações de entrada.
-
No VPN 3000 Concentrator, clique em Test para testar a conexão.
-
Se a autenticação for boa, o VPN 3000 Concentrator exibirá:
Autenticação Bem-Sucedida
No exemplo acima, definimos um servidor SDI global. Também podemos optar por definir servidores SDI individuais para cada grupo indo para Configuration > User Management > Groups, destacando o respectivo grupo e escolhendo Modify Auth Server.
Para obter informações sobre depuração, consulte as seguintes seções deste documento:
Verificar
Esta seção fornece informações que você pode usar para confirmar se sua configuração está funcionando adequadamente.
Testar o Cisco VPN Client para o VPN 3000 Concentrator com SDI
Se tudo funcionar até esse ponto, é hora de combinar o Cisco VPN Client, o VPN 3000 Concentrator e o servidor SDI. Precisamos fazer uma alteração no VPN 3000 Concentrator modificando o grupo em funcionamento que chamamos de vpn3000 para enviar solicitações ao servidor de SDI.
Troubleshoot
Esta seção fornece informações que podem ser usadas para o troubleshooting da sua configuração.
Ligando a depuração no VPN 3000 Concentrator
Nome da classe para autenticação:
-
AUTH
-
AUTHDBG
-
CÓDIGO AUTOMÁTICO
Nome da classe para IPSec:
-
IKE, IKEDBG, IKEDECODE
-
IPSEC, IPSECDBG, IPSECDECODE
-
Gravidade para registro = 1-9
-
Severidade para console = 1-3
Clique em Get Log para exibir os resultados da operação de depuração.
Bom debug de IPSec com autenticação local
1 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=1 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): 00 00 00 00 00 00 00 00
Next Payload : SA (1)
Exchange Type : Oakley Aggressive Mode
Flags : 0
Message ID : 0
Length : 307
7 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=1 161.44.17.135
RECEIVED Message (msgid=0) with payloads :
HDR + SA (1) + KE (4) + NONCE (10) + ID (5) + VENDOR (13) + NONE (0)
... total length : 307
10 10/10/2000 17:12:32.560 SEV=9 IKEDBG/0 RPT=2 161.44.17.135
processing SA payload
11 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=2 161.44.17.135
SA Payload Decode :
DOI : IPSEC (1)
Situation : Identity Only (1)
Length : 120
14 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=3 161.44.17.135
Proposal Decode:
Proposal # : 1
Protocol ID : ISAKMP (1)
#of Transforms: 4
Spi : 00 00 00 00
Length : 108
18 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=4 161.44.17.135
Transform # 1 Decode for Proposal # 1:
Transform # : 1
Transform ID : IKE (1)
Length : 24
20 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=5 161.44.17.135
Phase 1 SA Attribute Decode for Transform # 1:
Encryption Alg: DES-CBC (1)
Hash Alg : MD5 (1)
DH Group : Oakley Group 1 (1)
Auth Method : Preshared Key (1)
24 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=6 161.44.17.135
Transform # 2 Decode for Proposal # 1:
Transform # : 2
Transform ID : IKE (1)
Length : 24
26 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=7 161.44.17.135
Phase 1 SA Attribute Decode for Transform # 2:
Encryption Alg: Triple-DES (5)
Hash Alg : MD5 (1)
DH Group : Oakley Group 1 (1)
Auth Method : Preshared Key (1)
30 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=8 161.44.17.135
Transform # 3 Decode for Proposal # 1:
Transform # : 3
Transform ID : IKE (1)
Length : 24
32 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=9 161.44.17.135
Phase 1 SA Attribute Decode for Transform # 3:
Encryption Alg: Triple-DES (5)
Hash Alg : SHA (2)
DH Group : Oakley Group 1 (1)
Auth Method : Preshared Key (1)
36 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=10 161.44.17.135
Transform # 4 Decode for Proposal # 1:
Transform # : 4
Transform ID : IKE (1)
Length : 24
38 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=11 161.44.17.135
Phase 1 SA Attribute Decode for Transform # 4:
Encryption Alg: DES-CBC (1)
Hash Alg : SHA (2)
DH Group : Oakley Group 1 (1)
Auth Method : Preshared Key (1)
42 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=3 161.44.17.135
Proposal # 1, Transform # 1, Type ISAKMP, Id IKE
Parsing received transform:
Phase 1 failure against global IKE proposal # 1:
Mismatched attr types for class DH Group:
Rcv'd: Oakley Group 1
Cfg'd: Oakley Group 2
47 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=4 161.44.17.135
Phase 1 failure against global IKE proposal # 2:
Mismatched attr types for class Encryption Alg:
Rcv'd: DES-CBC
Cfg'd: Triple-DES
50 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=5 161.44.17.135
Proposal # 1, Transform # 2, Type ISAKMP, Id IKE
Parsing received transform:
Phase 1 failure against global IKE proposal # 1:
Mismatched attr types for class DH Group:
Rcv'd: Oakley Group 1
Cfg'd: Oakley Group 2
55 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=6 161.44.17.135
Proposal # 1, Transform # 3, Type ISAKMP, Id IKE
Parsing received transform:
Phase 1 failure against global IKE proposal # 1:
Mismatched attr types for class DH Group:
Rcv'd: Oakley Group 1
Cfg'd: Oakley Group 2
60 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=7 161.44.17.135
Phase 1 failure against global IKE proposal # 2:
Mismatched attr types for class Hash Alg:
Rcv'd: SHA
Cfg'd: MD5
62 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=8 161.44.17.135
Phase 1 failure against global IKE proposal # 3:
Mismatched attr types for class Encryption Alg:
Rcv'd: Triple-DES
Cfg'd: DES-CBC
65 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=9 161.44.17.135
Proposal # 1, Transform # 4, Type ISAKMP, Id IKE
Parsing received transform:
Phase 1 failure against global IKE proposal # 1:
Mismatched attr types for class DH Group:
Rcv'd: Oakley Group 1
Cfg'd: Oakley Group 2
70 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=10 161.44.17.135
Phase 1 failure against global IKE proposal # 2:
Mismatched attr types for class Encryption Alg:
Rcv'd: DES-CBC
Cfg'd: Triple-DES
73 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=11 161.44.17.135
Phase 1 failure against global IKE proposal # 3:
Mismatched attr types for class Hash Alg:
Rcv'd: SHA
Cfg'd: MD5
75 10/10/2000 17:12:32.560 SEV=7 IKEDBG/0 RPT=12 161.44.17.135
Oakley proposal is acceptable
76 10/10/2000 17:12:32.560 SEV=9 IKEDBG/0 RPT=13 161.44.17.135
processing ke payload
77 10/10/2000 17:12:32.560 SEV=9 IKEDBG/0 RPT=14 161.44.17.135
processing ISA_KE
78 10/10/2000 17:12:32.560 SEV=9 IKEDBG/1 RPT=1 161.44.17.135
processing nonce payload
79 10/10/2000 17:12:32.560 SEV=9 IKEDBG/1 RPT=2 161.44.17.135
Processing ID
80 10/10/2000 17:12:32.560 SEV=9 IKEDBG/1 RPT=3 161.44.17.135
processing vid payload
81 10/10/2000 17:12:32.580 SEV=9 IKEDBG/23 RPT=1 161.44.17.135
Starting group lookup for peer 161.44.17.135
82 10/10/2000 17:12:32.680 SEV=7 IKEDBG/0 RPT=15 161.44.17.135
Found Phase 1 Group (vpn3000)
83 10/10/2000 17:12:32.680 SEV=7 IKEDBG/14 RPT=1 161.44.17.135
Authentication configured for Internal
84 10/10/2000 17:12:32.680 SEV=9 IKEDBG/0 RPT=16 161.44.17.135
constructing ISA_SA for isakmp
85 10/10/2000 17:12:32.680 SEV=9 IKEDBG/0 RPT=17 161.44.17.135
constructing ke payload
86 10/10/2000 17:12:32.680 SEV=9 IKEDBG/1 RPT=4 161.44.17.135
constructing nonce payload
87 10/10/2000 17:12:32.680 SEV=9 IKE/0 RPT=1 161.44.17.135
Generating keys for Responder...
88 10/10/2000 17:12:32.680 SEV=9 IKEDBG/1 RPT=5 161.44.17.135
constructing ID
89 10/10/2000 17:12:32.680 SEV=9 IKEDBG/0 RPT=18
construct hash payload
90 10/10/2000 17:12:32.680 SEV=9 IKEDBG/0 RPT=19 161.44.17.135
computing hash
91 10/10/2000 17:12:32.680 SEV=9 IKEDBG/1 RPT=6 161.44.17.135
constructing vid payload
92 10/10/2000 17:12:32.680 SEV=8 IKEDBG/0 RPT=20 161.44.17.135
SENDING Message (msgid=0) with payloads :
HDR + SA (1) ... total length : 248
93 10/10/2000 17:12:32.730 SEV=8 IKEDECODE/0 RPT=12 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): B7 AD 34 D2 74 4D 05 DA
Next Payload : HASH (8)
Exchange Type : Oakley Aggressive Mode
Flags : 1 (ENCRYPT )
Message ID : 0
Length : 52
99 10/10/2000 17:12:32.730 SEV=8 IKEDBG/0 RPT=21 161.44.17.135
RECEIVED Message (msgid=0) with payloads :
HDR + HASH (8) + NONE (0) ... total length : 48
101 10/10/2000 17:12:32.730 SEV=9 IKEDBG/0 RPT=22 161.44.17.135
processing hash
102 10/10/2000 17:12:32.730 SEV=9 IKEDBG/0 RPT=23 161.44.17.135
computing hash
103 10/10/2000 17:12:33.410 SEV=8 IKEDECODE/0 RPT=13 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): B7 AD 34 D2 74 4D 05 DA
Next Payload : HASH (8)
Exchange Type : Oakley Quick Mode
Flags : 1 (ENCRYPT )
Message ID : 48687ca1
Length : 308
110 10/10/2000 17:12:33.410 SEV=9 IKEDBG/21 RPT=1 161.44.17.135
Delay Quick Mode processing, Cert/Trans Exch/RM DSID in progress
111 10/10/2000 17:12:33.410 SEV=9 IKEDBG/0 RPT=24 161.44.17.135
constructing blank hash
112 10/10/2000 17:12:33.410 SEV=9 IKEDBG/0 RPT=25 161.44.17.135
constructing qm hash
113 10/10/2000 17:12:33.410 SEV=8 IKEDBG/0 RPT=26 161.44.17.135
SENDING Message (msgid=fc2ce5eb) with payloads :
HDR + HASH (8) ... total length : 68
115 10/10/2000 17:12:44.680 SEV=8 IKEDECODE/0 RPT=14 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): B7 AD 34 D2 74 4D 05 DA
Next Payload : HASH (8)
Exchange Type : Oakley Transactional
Flags : 1 (ENCRYPT )
Message ID : fc2ce5eb
Length : 92
122 10/10/2000 17:12:44.680 SEV=8 IKEDBG/0 RPT=27 161.44.17.135
RECEIVED Message (msgid=fc2ce5eb) with payloads :
HDR + HASH (8) + ATTR (14) + NONE (0) ... total length : 85
124 10/10/2000 17:12:44.680 SEV=9 IKEDBG/1 RPT=7
process_attr(): Enter!
125 10/10/2000 17:12:44.680 SEV=9 IKEDBG/1 RPT=8
Processing cfg reply attributes.
126 10/10/2000 17:12:44.980 SEV=7 IKEDBG/14 RPT=2 161.44.17.135
User [ 37297304 ]
Authentication configured for Internal
127 10/10/2000 17:12:44.980 SEV=4 IKE/52 RPT=7 161.44.17.135
User [ 37297304 ]
User (37297304) authenticated.
128 10/10/2000 17:12:44.980 SEV=9 IKEDBG/31 RPT=1 161.44.17.135
User [ 37297304 ]
Obtained IP addr (192.168.1.1) prior to initiating Mode Cfg (XAuth enabled)
130 10/10/2000 17:12:44.980 SEV=9 IKEDBG/0 RPT=28 161.44.17.135
User [ 37297304 ]
constructing blank hash
131 10/10/2000 17:12:44.980 SEV=9 IKEDBG/0 RPT=29 161.44.17.135
0000: 00010004 C0A80101 F0010000 ............
132 10/10/2000 17:12:44.980 SEV=9 IKEDBG/0 RPT=30 161.44.17.135
User [ 37297304 ]
constructing QM hash
133 10/10/2000 17:12:44.980 SEV=8 IKEDBG/0 RPT=31 161.44.17.135
SENDING Message (msgid=fc2ce5eb) with payloads :
HDR + HASH (8) ... total length : 80
135 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=15 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): B7 AD 34 D2 74 4D 05 DA
Next Payload : HASH (8)
Exchange Type : Oakley Transactional
Flags : 1 (ENCRYPT )
Message ID : fc2ce5eb
Length : 68
142 10/10/2000 17:12:44.990 SEV=8 IKEDBG/0 RPT=32 161.44.17.135
RECEIVED Message (msgid=fc2ce5eb) with payloads :
HDR + HASH (8) + ATTR (14) + NONE (0) ... total length : 64
144 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=9
process_attr(): Enter!
145 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=10
Processing cfg ACK attributes
146 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=11
Received IPV4 address ack!
147 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=12
Received Save PW ack!
148 10/10/2000 17:12:44.990 SEV=4 AUTH/21 RPT=18
User 37297304 connected
149 10/10/2000 17:12:44.990 SEV=7 IKEDBG/22 RPT=1 161.44.17.135
User [ 37297304 ]
Resume Quick Mode processing, Cert/Trans Exch/RM DSID completed
151 10/10/2000 17:12:44.990 SEV=8 IKEDBG/0 RPT=33 161.44.17.135
RECEIVED Message (msgid=48687ca1) with payloads :
HDR + HASH (8) + SA (1) + NONCE (10) + ID (5) + ID (5) + NOTIFY (11) + NONE (0)
... total length : 304
154 10/10/2000 17:12:44.990 SEV=9 IKEDBG/0 RPT=34 161.44.17.135
User [ 37297304 ]
processing hash
155 10/10/2000 17:12:44.990 SEV=9 IKEDBG/0 RPT=35 161.44.17.135
User [ 37297304 ]
processing SA payload
156 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=16 161.44.17.135
SA Payload Decode :
DOI : IPSEC (1)
Situation : Identity Only (1)
Length : 180
159 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=17 161.44.17.135
Proposal Decode:
Proposal # : 1
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
163 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=18 161.44.17.135
Transform # 1 Decode for Proposal # 1:
Transform # : 1
Transform ID : DES-CBC (2)
Length : 16
165 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=19 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: MD5 (1)
Encapsulation : Tunnel (1)
167 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=20 161.44.17.135
Proposal Decode:
Proposal # : 2
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
171 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=21 161.44.17.135
Transform # 1 Decode for Proposal # 2:
Transform # : 1
Transform ID : Triple-DES (3)
Length : 16
173 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=22 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: MD5 (1)
Encapsulation : Tunnel (1)
175 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=23 161.44.17.135
Proposal Decode:
Proposal # : 3
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
179 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=24 161.44.17.135
Transform # 1 Decode for Proposal # 3:
Transform # : 1
Transform ID : DES-CBC (2)
Length : 16
181 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=25 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: SHA (2)
Encapsulation : Tunnel (1)
183 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=26 161.44.17.135
Proposal Decode:
Proposal # : 4
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
187 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=27 161.44.17.135
Transform # 1 Decode for Proposal # 4:
Transform # : 1
Transform ID : Triple-DES (3)
Length : 16
189 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=28 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: SHA (2)
Encapsulation : Tunnel (1)
191 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=29 161.44.17.135
Proposal Decode:
Proposal # : 5
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
195 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=30 161.44.17.135
Transform # 1 Decode for Proposal # 5:
Transform # : 1
Transform ID : NULL (11)
Length : 16
197 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=31 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: MD5 (1)
Encapsulation : Tunnel (1)
199 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=32 161.44.17.135
Proposal Decode:
Proposal # : 6
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
203 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=33 161.44.17.135
Transform # 1 Decode for Proposal # 6:
Transform # : 1
Transform ID : NULL (11)
Length : 16
205 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=34 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: SHA (2)
Encapsulation : Tunnel (1)
207 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=13 161.44.17.135
User [ 37297304 ]
processing nonce payload
208 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=14 161.44.17.135
User [ 37297304 ]
Processing ID
209 10/10/2000 17:12:44.990 SEV=5 IKE/25 RPT=13 161.44.17.135
User [ 37297304 ]
Received remote Proxy Host data in ID Payload:
Address 161.44.17.135, Protocol 0, Port 0
212 10/10/2000 17:12:44.990 SEV=7 IKEDBG/1 RPT=15 161.44.17.135
User [ 37297304 ]
Modifying client proxy src address!
213 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=16 161.44.17.135
User [ 37297304 ]
Processing ID
214 10/10/2000 17:12:44.990 SEV=5 IKE/24 RPT=7 161.44.17.135
User [ 37297304 ]
Received local Proxy Host data in ID Payload:
Address 172.18.124.134, Protocol 0, Port 0
217 10/10/2000 17:12:44.990 SEV=9 IKEDBG/0 RPT=36 161.44.17.135
User [ 37297304 ]
Processing Notify payload
218 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=35 161.44.17.135
Notify Payload Decode :
DOI : IPSEC (1)
Protocol : ISAKMP (1)
Message : Initial contact (24578)
Spi : 9D F3 34 FE 89 BF AA B2 B7 AD 34 D2 74 4D 05 DA
Length : 28
224 10/10/2000 17:12:44.990 SEV=8 IKEDBG/0 RPT=37
QM IsRekeyed old sa not found by addr
225 10/10/2000 17:12:44.990 SEV=5 IKE/66 RPT=13 161.44.17.135
User [ 37297304 ]
IKE Remote Peer configured for SA: ESP-3DES-MD5
226 10/10/2000 17:12:44.990 SEV=9 IKEDBG/0 RPT=38 161.44.17.135
User [ 37297304 ]
processing IPSEC SA
227 10/10/2000 17:12:44.990 SEV=8 IKEDBG/0 RPT=39
Proposal # 1, Transform # 1, Type ESP, Id DES-CBC
Parsing received transform:
Phase 2 failure:
Mismatched transform IDs for protocol ESP:
Rcv'd: DES-CBC
Cfg'd: Triple-DES
232 10/10/2000 17:12:45.000 SEV=7 IKEDBG/27 RPT=1 161.44.17.135
User [ 37297304 ]
IPSec SA Proposal # 2, Transform # 1 acceptable
233 10/10/2000 17:12:45.000 SEV=7 IKEDBG/0 RPT=40 161.44.17.135
User [ 37297304 ]
IKE: requesting SPI!
234 10/10/2000 17:12:45.000 SEV=6 IKE/0 RPT=2
AM received unexpected event EV_ACTIVATE_NEW_SA in state AM_ACTIVE
235 10/10/2000 17:12:45.000 SEV=9 IPSECDBG/6 RPT=1
IPSEC key message parse - msgtype 6, len 164, vers 1, pid 00000000, seq 13,
err 0, type 2, mode 0, state 32, label 0, pad 0, spi 00000000, encrKeyLen 0,
hashKeyLen 0, ivlen 0, alg 0, hmacAlg 0, lifetype 0, lifetime1 300,
lifetime2 2000000000, dsId 2
239 10/10/2000 17:12:45.000 SEV=9 IPSECDBG/1 RPT=1
Processing KEY_GETSPI msg!
240 10/10/2000 17:12:45.000 SEV=7 IPSECDBG/13 RPT=1
Reserved SPI 1773955517
241 10/10/2000 17:12:45.000 SEV=8 IKEDBG/6 RPT=1
IKE got SPI from key engine: SPI = 0x69bc69bd
242 10/10/2000 17:12:45.000 SEV=9 IKEDBG/0 RPT=41 161.44.17.135
User [ 37297304 ]
oakley constructing quick mode
243 10/10/2000 17:12:45.000 SEV=9 IKEDBG/0 RPT=42 161.44.17.135
User [ 37297304 ]
constructing blank hash
244 10/10/2000 17:12:45.000 SEV=9 IKEDBG/0 RPT=43 161.44.17.135
User [ 37297304 ]
constructing ISA_SA for ipsec
245 10/10/2000 17:12:45.000 SEV=9 IKEDBG/1 RPT=17 161.44.17.135
User [ 37297304 ]
constructing ipsec nonce payload
246 10/10/2000 17:12:45.000 SEV=9 IKEDBG/1 RPT=18 161.44.17.135
User [ 37297304 ]
constructing proxy ID
247 10/10/2000 17:12:45.000 SEV=7 IKEDBG/0 RPT=44 161.44.17.135
User [ 37297304 ]
Transmitting Proxy Id:
Remote host: 192.168.1.1 Protocol 0 Port 0
Local host: 172.18.124.134 Protocol 0 Port 0
251 10/10/2000 17:12:45.000 SEV=9 IKEDBG/0 RPT=45 161.44.17.135
User [ 37297304 ]
constructing QM hash
252 10/10/2000 17:12:45.000 SEV=8 IKEDBG/0 RPT=46 161.44.17.135
SENDING Message (msgid=48687ca1) with payloads :
HDR + HASH (8) ... total length : 136
254 10/10/2000 17:12:45.010 SEV=8 IKEDECODE/0 RPT=36 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): B7 AD 34 D2 74 4D 05 DA
Next Payload : HASH (8)
Exchange Type : Oakley Quick Mode
Flags : 1 (ENCRYPT )
Message ID : 48687ca1
Length : 52
261 10/10/2000 17:12:45.010 SEV=8 IKEDBG/0 RPT=47 161.44.17.135
RECEIVED Message (msgid=48687ca1) with payloads :
HDR + HASH (8) + NONE (0) ... total length : 48
263 10/10/2000 17:12:45.010 SEV=9 IKEDBG/0 RPT=48 161.44.17.135
User [ 37297304 ]
processing hash
264 10/10/2000 17:12:45.010 SEV=9 IKEDBG/0 RPT=49 161.44.17.135
User [ 37297304 ]
loading all IPSEC SAs
265 10/10/2000 17:12:45.010 SEV=9 IKEDBG/1 RPT=19 161.44.17.135
User [ 37297304 ]
Generating Quick Mode Key!
266 10/10/2000 17:12:45.010 SEV=9 IKEDBG/1 RPT=20 161.44.17.135
User [ 37297304 ]
Generating Quick Mode Key!
267 10/10/2000 17:12:45.020 SEV=7 IKEDBG/0 RPT=50 161.44.17.135
User [ 37297304 ]
Loading host:
Dst: 172.18.124.134
Src: 192.168.1.1
268 10/10/2000 17:12:45.020 SEV=4 IKE/49 RPT=13 161.44.17.135
User [ 37297304 ]
Security negotiation complete for User (37297304)
Responder, Inbound SPI = 0x69bc69bd, Outbound SPI = 0x991518b4
271 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/6 RPT=2
IPSEC key message parse - msgtype 1, Len 536, vers 1, pid 00000000, seq 0,
err 0, type 2, mode 1, state 64, label 0, pad 0, spi 991518b4, encrKeyLen 24,
hashKeyLen 16, ivlen 8, alg 2, hmacAlg 3, lifetype 0, lifetime1 0,
lifetime2 0, dsId 2
274 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=2
Processing KEY_ADD MSG!
275 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=3
key_msghdr2secassoc(): Enter
276 10/10/2000 17:12:45.020 SEV=7 IPSECDBG/1 RPT=4
No USER filter configured
277 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=5
KeyProcessAdd: Enter
278 10/10/2000 17:12:45.020 SEV=8 IPSECDBG/1 RPT=6
KeyProcessAdd: Adding outbound SA
279 10/10/2000 17:12:45.020 SEV=8 IPSECDBG/1 RPT=7
KeyProcessAdd: src 172.18.124.134 mask 0.0.0.0, dst 192.168.1.1 mask 0.0.0.0
280 10/10/2000 17:12:45.020 SEV=8 IPSECDBG/1 RPT=8
KeyProcessAdd: FilterIpsecAddIkeSa success
281 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/6 RPT=3
IPSEC key message parse - msgtype 3, Len 292, vers 1, pid 00000000, seq 0,
err 0, type 2, mode 1, state 32, label 0, pad 0, spi 69bc69bd, encrKeyLen 24,
hashKeyLen 16, ivlen 8, alg 2, hmacAlg 3, lifetype 0, lifetime1 0,
lifetime2 0, dsId 2
284 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=9
Processing KEY_UPDATE MSG!
285 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=10
Update inbound SA addresses
286 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=11
key_msghdr2secassoc(): Enter
287 10/10/2000 17:12:45.020 SEV=7 IPSECDBG/1 RPT=12
No USER filter configured
288 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=13
KeyProcessUpdate: Enter
289 10/10/2000 17:12:45.020 SEV=8 IPSECDBG/1 RPT=14
KeyProcessUpdate: success
290 10/10/2000 17:12:45.020 SEV=8 IKEDBG/7 RPT=1
IKE got a KEY_ADD MSG for SA: SPI = 0x991518b4
291 10/10/2000 17:12:45.020 SEV=8 IKEDBG/0 RPT=51
pitcher: rcv KEY_UPDATE, spi 0x69bc69bd
Bom debug de IPSec com autenticação local
1 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=1 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): 00 00 00 00 00 00 00 00
Next Payload : SA (1)
Exchange Type : Oakley Aggressive Mode
Flags : 0
Message ID : 0
Length : 307
7 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=1 161.44.17.135
RECEIVED Message (msgid=0) with payloads :
HDR + SA (1) + KE (4) + NONCE (10) + ID (5) + VENDOR (13) + NONE (0)
... total length : 307
10 10/10/2000 17:12:32.560 SEV=9 IKEDBG/0 RPT=2 161.44.17.135
processing SA payload
11 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=2 161.44.17.135
SA Payload Decode :
DOI : IPSEC (1)
Situation : Identity Only (1)
Length : 120
14 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=3 161.44.17.135
Proposal Decode:
Proposal # : 1
Protocol ID : ISAKMP (1)
#of Transforms: 4
Spi : 00 00 00 00
Length : 108
18 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=4 161.44.17.135
Transform # 1 Decode for Proposal # 1:
Transform # : 1
Transform ID : IKE (1)
Length : 24
20 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=5 161.44.17.135
Phase 1 SA Attribute Decode for Transform # 1:
Encryption Alg: DES-CBC (1)
Hash Alg : MD5 (1)
DH Group : Oakley Group 1 (1)
Auth Method : Preshared Key (1)
24 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=6 161.44.17.135
Transform # 2 Decode for Proposal # 1:
Transform # : 2
Transform ID : IKE (1)
Length : 24
26 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=7 161.44.17.135
Phase 1 SA Attribute Decode for Transform # 2:
Encryption Alg: Triple-DES (5)
Hash Alg : MD5 (1)
DH Group : Oakley Group 1 (1)
Auth Method : Preshared Key (1)
30 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=8 161.44.17.135
Transform # 3 Decode for Proposal # 1:
Transform # : 3
Transform ID : IKE (1)
Length : 24
32 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=9 161.44.17.135
Phase 1 SA Attribute Decode for Transform # 3:
Encryption Alg: Triple-DES (5)
Hash Alg : SHA (2)
DH Group : Oakley Group 1 (1)
Auth Method : Preshared Key (1)
36 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=10 161.44.17.135
Transform # 4 Decode for Proposal # 1:
Transform # : 4
Transform ID : IKE (1)
Length : 24
38 10/10/2000 17:12:32.560 SEV=8 IKEDECODE/0 RPT=11 161.44.17.135
Phase 1 SA Attribute Decode for Transform # 4:
Encryption Alg: DES-CBC (1)
Hash Alg : SHA (2)
DH Group : Oakley Group 1 (1)
Auth Method : Preshared Key (1)
42 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=3 161.44.17.135
Proposal # 1, Transform # 1, Type ISAKMP, Id IKE
Parsing received transform:
Phase 1 failure against global IKE proposal # 1:
Mismatched attr types for class DH Group:
Rcv'd: Oakley Group 1
Cfg'd: Oakley Group 2
47 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=4 161.44.17.135
Phase 1 failure against global IKE proposal # 2:
Mismatched attr types for class Encryption Alg:
Rcv'd: DES-CBC
Cfg'd: Triple-DES
50 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=5 161.44.17.135
Proposal # 1, Transform # 2, Type ISAKMP, Id IKE
Parsing received transform:
Phase 1 failure against global IKE proposal # 1:
Mismatched attr types for class DH Group:
Rcv'd: Oakley Group 1
Cfg'd: Oakley Group 2
55 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=6 161.44.17.135
Proposal # 1, Transform # 3, Type ISAKMP, Id IKE
Parsing received transform:
Phase 1 failure against global IKE proposal # 1:
Mismatched attr types for class DH Group:
Rcv'd: Oakley Group 1
Cfg'd: Oakley Group 2
60 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=7 161.44.17.135
Phase 1 failure against global IKE proposal # 2:
Mismatched attr types for class Hash Alg:
Rcv'd: SHA
Cfg'd: MD5
62 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=8 161.44.17.135
Phase 1 failure against global IKE proposal # 3:
Mismatched attr types for class Encryption Alg:
Rcv'd: Triple-DES
Cfg'd: DES-CBC
65 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=9 161.44.17.135
Proposal # 1, Transform # 4, Type ISAKMP, Id IKE
Parsing received transform:
Phase 1 failure against global IKE proposal # 1:
Mismatched attr types for class DH Group:
Rcv'd: Oakley Group 1
Cfg'd: Oakley Group 2
70 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=10 161.44.17.135
Phase 1 failure against global IKE proposal # 2:
Mismatched attr types for class Encryption Alg:
Rcv'd: DES-CBC
Cfg'd: Triple-DES
73 10/10/2000 17:12:32.560 SEV=8 IKEDBG/0 RPT=11 161.44.17.135
Phase 1 failure against global IKE proposal # 3:
Mismatched attr types for class Hash Alg:
Rcv'd: SHA
Cfg'd: MD5
75 10/10/2000 17:12:32.560 SEV=7 IKEDBG/0 RPT=12 161.44.17.135
Oakley proposal is acceptable
76 10/10/2000 17:12:32.560 SEV=9 IKEDBG/0 RPT=13 161.44.17.135
processing ke payload
77 10/10/2000 17:12:32.560 SEV=9 IKEDBG/0 RPT=14 161.44.17.135
processing ISA_KE
78 10/10/2000 17:12:32.560 SEV=9 IKEDBG/1 RPT=1 161.44.17.135
processing nonce payload
79 10/10/2000 17:12:32.560 SEV=9 IKEDBG/1 RPT=2 161.44.17.135
Processing ID
80 10/10/2000 17:12:32.560 SEV=9 IKEDBG/1 RPT=3 161.44.17.135
processing vid payload
81 10/10/2000 17:12:32.580 SEV=9 IKEDBG/23 RPT=1 161.44.17.135
Starting group lookup for peer 161.44.17.135
82 10/10/2000 17:12:32.680 SEV=7 IKEDBG/0 RPT=15 161.44.17.135
Found Phase 1 Group (vpn3000)
83 10/10/2000 17:12:32.680 SEV=7 IKEDBG/14 RPT=1 161.44.17.135
Authentication configured for Internal
84 10/10/2000 17:12:32.680 SEV=9 IKEDBG/0 RPT=16 161.44.17.135
constructing ISA_SA for isakmp
85 10/10/2000 17:12:32.680 SEV=9 IKEDBG/0 RPT=17 161.44.17.135
constructing ke payload
86 10/10/2000 17:12:32.680 SEV=9 IKEDBG/1 RPT=4 161.44.17.135
constructing nonce payload
87 10/10/2000 17:12:32.680 SEV=9 IKE/0 RPT=1 161.44.17.135
Generating keys for Responder...
88 10/10/2000 17:12:32.680 SEV=9 IKEDBG/1 RPT=5 161.44.17.135
constructing ID
89 10/10/2000 17:12:32.680 SEV=9 IKEDBG/0 RPT=18
construct hash payload
90 10/10/2000 17:12:32.680 SEV=9 IKEDBG/0 RPT=19 161.44.17.135
computing hash
91 10/10/2000 17:12:32.680 SEV=9 IKEDBG/1 RPT=6 161.44.17.135
constructing vid payload
92 10/10/2000 17:12:32.680 SEV=8 IKEDBG/0 RPT=20 161.44.17.135
SENDING Message (msgid=0) with payloads :
HDR + SA (1) ... total length : 248
93 10/10/2000 17:12:32.730 SEV=8 IKEDECODE/0 RPT=12 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): B7 AD 34 D2 74 4D 05 DA
Next Payload : HASH (8)
Exchange Type : Oakley Aggressive Mode
Flags : 1 (ENCRYPT )
Message ID : 0
Length : 52
99 10/10/2000 17:12:32.730 SEV=8 IKEDBG/0 RPT=21 161.44.17.135
RECEIVED Message (msgid=0) with payloads :
HDR + HASH (8) + NONE (0) ... total length : 48
101 10/10/2000 17:12:32.730 SEV=9 IKEDBG/0 RPT=22 161.44.17.135
processing hash
102 10/10/2000 17:12:32.730 SEV=9 IKEDBG/0 RPT=23 161.44.17.135
computing hash
103 10/10/2000 17:12:33.410 SEV=8 IKEDECODE/0 RPT=13 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): B7 AD 34 D2 74 4D 05 DA
Next Payload : HASH (8)
Exchange Type : Oakley Quick Mode
Flags : 1 (ENCRYPT )
Message ID : 48687ca1
Length : 308
110 10/10/2000 17:12:33.410 SEV=9 IKEDBG/21 RPT=1 161.44.17.135
Delay Quick Mode processing, Cert/Trans Exch/RM DSID in progress
111 10/10/2000 17:12:33.410 SEV=9 IKEDBG/0 RPT=24 161.44.17.135
constructing blank hash
112 10/10/2000 17:12:33.410 SEV=9 IKEDBG/0 RPT=25 161.44.17.135
constructing qm hash
113 10/10/2000 17:12:33.410 SEV=8 IKEDBG/0 RPT=26 161.44.17.135
SENDING Message (msgid=fc2ce5eb) with payloads :
HDR + HASH (8) ... total length : 68
115 10/10/2000 17:12:44.680 SEV=8 IKEDECODE/0 RPT=14 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): B7 AD 34 D2 74 4D 05 DA
Next Payload : HASH (8)
Exchange Type : Oakley Transactional
Flags : 1 (ENCRYPT )
Message ID : fc2ce5eb
Length : 92
122 10/10/2000 17:12:44.680 SEV=8 IKEDBG/0 RPT=27 161.44.17.135
RECEIVED Message (msgid=fc2ce5eb) with payloads :
HDR + HASH (8) + ATTR (14) + NONE (0) ... total length : 85
124 10/10/2000 17:12:44.680 SEV=9 IKEDBG/1 RPT=7
process_attr(): Enter!
125 10/10/2000 17:12:44.680 SEV=9 IKEDBG/1 RPT=8
Processing cfg reply attributes.
126 10/10/2000 17:12:44.980 SEV=7 IKEDBG/14 RPT=2 161.44.17.135
User [ 37297304 ]
Authentication configured for Internal
127 10/10/2000 17:12:44.980 SEV=4 IKE/52 RPT=7 161.44.17.135
User [ 37297304 ]
User (37297304) authenticated.
128 10/10/2000 17:12:44.980 SEV=9 IKEDBG/31 RPT=1 161.44.17.135
User [ 37297304 ]
Obtained IP addr (192.168.1.1) prior to initiating Mode Cfg (XAuth enabled)
130 10/10/2000 17:12:44.980 SEV=9 IKEDBG/0 RPT=28 161.44.17.135
User [ 37297304 ]
constructing blank hash
131 10/10/2000 17:12:44.980 SEV=9 IKEDBG/0 RPT=29 161.44.17.135
0000: 00010004 C0A80101 F0010000 ............
132 10/10/2000 17:12:44.980 SEV=9 IKEDBG/0 RPT=30 161.44.17.135
User [ 37297304 ]
constructing QM hash
133 10/10/2000 17:12:44.980 SEV=8 IKEDBG/0 RPT=31 161.44.17.135
SENDING Message (msgid=fc2ce5eb) with payloads :
HDR + HASH (8) ... total length : 80
135 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=15 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): B7 AD 34 D2 74 4D 05 DA
Next Payload : HASH (8)
Exchange Type : Oakley Transactional
Flags : 1 (ENCRYPT )
Message ID : fc2ce5eb
Length : 68
142 10/10/2000 17:12:44.990 SEV=8 IKEDBG/0 RPT=32 161.44.17.135
RECEIVED Message (msgid=fc2ce5eb) with payloads :
HDR + HASH (8) + ATTR (14) + NONE (0) ... total length : 64
144 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=9
process_attr(): Enter!
145 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=10
Processing cfg ACK attributes
146 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=11
Received IPV4 address ack!
147 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=12
Received Save PW ack!
148 10/10/2000 17:12:44.990 SEV=4 AUTH/21 RPT=18
User 37297304 connected
149 10/10/2000 17:12:44.990 SEV=7 IKEDBG/22 RPT=1 161.44.17.135
User [ 37297304 ]
Resume Quick Mode processing, Cert/Trans Exch/RM DSID completed
151 10/10/2000 17:12:44.990 SEV=8 IKEDBG/0 RPT=33 161.44.17.135
RECEIVED Message (msgid=48687ca1) with payloads :
HDR + HASH (8) + SA (1) + NONCE (10) + ID (5) + ID (5) + NOTIFY (11) + NONE (0)
... total length : 304
154 10/10/2000 17:12:44.990 SEV=9 IKEDBG/0 RPT=34 161.44.17.135
User [ 37297304 ]
processing hash
155 10/10/2000 17:12:44.990 SEV=9 IKEDBG/0 RPT=35 161.44.17.135
User [ 37297304 ]
processing SA payload
156 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=16 161.44.17.135
SA Payload Decode :
DOI : IPSEC (1)
Situation : Identity Only (1)
Length : 180
159 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=17 161.44.17.135
Proposal Decode:
Proposal # : 1
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
163 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=18 161.44.17.135
Transform # 1 Decode for Proposal # 1:
Transform # : 1
Transform ID : DES-CBC (2)
Length : 16
165 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=19 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: MD5 (1)
Encapsulation : Tunnel (1)
167 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=20 161.44.17.135
Proposal Decode:
Proposal # : 2
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
171 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=21 161.44.17.135
Transform # 1 Decode for Proposal # 2:
Transform # : 1
Transform ID : Triple-DES (3)
Length : 16
173 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=22 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: MD5 (1)
Encapsulation : Tunnel (1)
175 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=23 161.44.17.135
Proposal Decode:
Proposal # : 3
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
179 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=24 161.44.17.135
Transform # 1 Decode for Proposal # 3:
Transform # : 1
Transform ID : DES-CBC (2)
Length : 16
181 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=25 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: SHA (2)
Encapsulation : Tunnel (1)
183 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=26 161.44.17.135
Proposal Decode:
Proposal # : 4
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
187 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=27 161.44.17.135
Transform # 1 Decode for Proposal # 4:
Transform # : 1
Transform ID : Triple-DES (3)
Length : 16
189 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=28 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: SHA (2)
Encapsulation : Tunnel (1)
191 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=29 161.44.17.135
Proposal Decode:
Proposal # : 5
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
195 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=30 161.44.17.135
Transform # 1 Decode for Proposal # 5:
Transform # : 1
Transform ID : NULL (11)
Length : 16
197 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=31 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: MD5 (1)
Encapsulation : Tunnel (1)
199 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=32 161.44.17.135
Proposal Decode:
Proposal # : 6
Protocol ID : ESP (3)
#of Transforms: 1
Spi : 99 15 18 B4
Length : 28
203 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=33 161.44.17.135
Transform # 1 Decode for Proposal # 6:
Transform # : 1
Transform ID : NULL (11)
Length : 16
205 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=34 161.44.17.135
Phase 2 SA Attribute Decode for Transform # 1:
HMAC Algorithm: SHA (2)
Encapsulation : Tunnel (1)
207 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=13 161.44.17.135
User [ 37297304 ]
processing nonce payload
208 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=14 161.44.17.135
User [ 37297304 ]
Processing ID
209 10/10/2000 17:12:44.990 SEV=5 IKE/25 RPT=13 161.44.17.135
User [ 37297304 ]
Received remote Proxy Host data in ID Payload:
Address 161.44.17.135, Protocol 0, Port 0
212 10/10/2000 17:12:44.990 SEV=7 IKEDBG/1 RPT=15 161.44.17.135
User [ 37297304 ]
Modifying client proxy src address!
213 10/10/2000 17:12:44.990 SEV=9 IKEDBG/1 RPT=16 161.44.17.135
User [ 37297304 ]
Processing ID
214 10/10/2000 17:12:44.990 SEV=5 IKE/24 RPT=7 161.44.17.135
User [ 37297304 ]
Received local Proxy Host data in ID Payload:
Address 172.18.124.134, Protocol 0, Port 0
217 10/10/2000 17:12:44.990 SEV=9 IKEDBG/0 RPT=36 161.44.17.135
User [ 37297304 ]
Processing Notify payload
218 10/10/2000 17:12:44.990 SEV=8 IKEDECODE/0 RPT=35 161.44.17.135
Notify Payload Decode :
DOI : IPSEC (1)
Protocol : ISAKMP (1)
Message : Initial contact (24578)
Spi : 9D F3 34 FE 89 BF AA B2 B7 AD 34 D2 74 4D 05 DA
Length : 28
224 10/10/2000 17:12:44.990 SEV=8 IKEDBG/0 RPT=37
QM IsRekeyed old sa not found by addr
225 10/10/2000 17:12:44.990 SEV=5 IKE/66 RPT=13 161.44.17.135
User [ 37297304 ]
IKE Remote Peer configured for SA: ESP-3DES-MD5
226 10/10/2000 17:12:44.990 SEV=9 IKEDBG/0 RPT=38 161.44.17.135
User [ 37297304 ]
processing IPSEC SA
227 10/10/2000 17:12:44.990 SEV=8 IKEDBG/0 RPT=39
Proposal # 1, Transform # 1, Type ESP, Id DES-CBC
Parsing received transform:
Phase 2 failure:
Mismatched transform IDs for protocol ESP:
Rcv'd: DES-CBC
Cfg'd: Triple-DES
232 10/10/2000 17:12:45.000 SEV=7 IKEDBG/27 RPT=1 161.44.17.135
User [ 37297304 ]
IPSec SA Proposal # 2, Transform # 1 acceptable
233 10/10/2000 17:12:45.000 SEV=7 IKEDBG/0 RPT=40 161.44.17.135
User [ 37297304 ]
IKE: requesting SPI!
234 10/10/2000 17:12:45.000 SEV=6 IKE/0 RPT=2
AM received unexpected event EV_ACTIVATE_NEW_SA in state AM_ACTIVE
235 10/10/2000 17:12:45.000 SEV=9 IPSECDBG/6 RPT=1
IPSEC key message parse - msgtype 6, len 164, vers 1, pid 00000000, seq 13,
err 0, type 2, mode 0, state 32, label 0, pad 0, spi 00000000, encrKeyLen 0,
hashKeyLen 0, ivlen 0, alg 0, hmacAlg 0, lifetype 0, lifetime1 300,
lifetime2 2000000000, dsId 2
239 10/10/2000 17:12:45.000 SEV=9 IPSECDBG/1 RPT=1
Processing KEY_GETSPI msg!
240 10/10/2000 17:12:45.000 SEV=7 IPSECDBG/13 RPT=1
Reserved SPI 1773955517
241 10/10/2000 17:12:45.000 SEV=8 IKEDBG/6 RPT=1
IKE got SPI from key engine: SPI = 0x69bc69bd
242 10/10/2000 17:12:45.000 SEV=9 IKEDBG/0 RPT=41 161.44.17.135
User [ 37297304 ]
oakley constructing quick mode
243 10/10/2000 17:12:45.000 SEV=9 IKEDBG/0 RPT=42 161.44.17.135
User [ 37297304 ]
constructing blank hash
244 10/10/2000 17:12:45.000 SEV=9 IKEDBG/0 RPT=43 161.44.17.135
User [ 37297304 ]
constructing ISA_SA for ipsec
245 10/10/2000 17:12:45.000 SEV=9 IKEDBG/1 RPT=17 161.44.17.135
User [ 37297304 ]
constructing ipsec nonce payload
246 10/10/2000 17:12:45.000 SEV=9 IKEDBG/1 RPT=18 161.44.17.135
User [ 37297304 ]
constructing proxy ID
247 10/10/2000 17:12:45.000 SEV=7 IKEDBG/0 RPT=44 161.44.17.135
User [ 37297304 ]
Transmitting Proxy Id:
Remote host: 192.168.1.1 Protocol 0 Port 0
Local host: 172.18.124.134 Protocol 0 Port 0
251 10/10/2000 17:12:45.000 SEV=9 IKEDBG/0 RPT=45 161.44.17.135
User [ 37297304 ]
constructing QM hash
252 10/10/2000 17:12:45.000 SEV=8 IKEDBG/0 RPT=46 161.44.17.135
SENDING Message (msgid=48687ca1) with payloads :
HDR + HASH (8) ... total length : 136
254 10/10/2000 17:12:45.010 SEV=8 IKEDECODE/0 RPT=36 161.44.17.135
ISAKMP HEADER : ( Version 1.0 )
Initiator Cookie(8): 9D F3 34 FE 89 BF AA B2
Responder Cookie(8): B7 AD 34 D2 74 4D 05 DA
Next Payload : HASH (8)
Exchange Type : Oakley Quick Mode
Flags : 1 (ENCRYPT )
Message ID : 48687ca1
Length : 52
261 10/10/2000 17:12:45.010 SEV=8 IKEDBG/0 RPT=47 161.44.17.135
RECEIVED Message (msgid=48687ca1) with payloads :
HDR + HASH (8) + NONE (0) ... total length : 48
263 10/10/2000 17:12:45.010 SEV=9 IKEDBG/0 RPT=48 161.44.17.135
User [ 37297304 ]
processing hash
264 10/10/2000 17:12:45.010 SEV=9 IKEDBG/0 RPT=49 161.44.17.135
User [ 37297304 ]
loading all IPSEC SAs
265 10/10/2000 17:12:45.010 SEV=9 IKEDBG/1 RPT=19 161.44.17.135
User [ 37297304 ]
Generating Quick Mode Key!
266 10/10/2000 17:12:45.010 SEV=9 IKEDBG/1 RPT=20 161.44.17.135
User [ 37297304 ]
Generating Quick Mode Key!
267 10/10/2000 17:12:45.020 SEV=7 IKEDBG/0 RPT=50 161.44.17.135
User [ 37297304 ]
Loading host:
Dst: 172.18.124.134
Src: 192.168.1.1
268 10/10/2000 17:12:45.020 SEV=4 IKE/49 RPT=13 161.44.17.135
User [ 37297304 ]
Security negotiation complete for User (37297304)
Responder, Inbound SPI = 0x69bc69bd, Outbound SPI = 0x991518b4
271 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/6 RPT=2
IPSEC key message parse - msgtype 1, Len 536, vers 1, pid 00000000, seq 0,
err 0, type 2, mode 1, state 64, label 0, pad 0, spi 991518b4, encrKeyLen 24,
hashKeyLen 16, ivlen 8, alg 2, hmacAlg 3, lifetype 0, lifetime1 0,
lifetime2 0, dsId 2
274 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=2
Processing KEY_ADD MSG!
275 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=3
key_msghdr2secassoc(): Enter
276 10/10/2000 17:12:45.020 SEV=7 IPSECDBG/1 RPT=4
No USER filter configured
277 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=5
KeyProcessAdd: Enter
278 10/10/2000 17:12:45.020 SEV=8 IPSECDBG/1 RPT=6
KeyProcessAdd: Adding outbound SA
279 10/10/2000 17:12:45.020 SEV=8 IPSECDBG/1 RPT=7
KeyProcessAdd: src 172.18.124.134 mask 0.0.0.0, dst 192.168.1.1 mask 0.0.0.0
280 10/10/2000 17:12:45.020 SEV=8 IPSECDBG/1 RPT=8
KeyProcessAdd: FilterIpsecAddIkeSa success
281 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/6 RPT=3
IPSEC key message parse - msgtype 3, Len 292, vers 1, pid 00000000, seq 0,
err 0, type 2, mode 1, state 32, label 0, pad 0, spi 69bc69bd, encrKeyLen 24,
hashKeyLen 16, ivlen 8, alg 2, hmacAlg 3, lifetype 0, lifetime1 0,
lifetime2 0, dsId 2
284 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=9
Processing KEY_UPDATE MSG!
285 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=10
Update inbound SA addresses
286 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=11
key_msghdr2secassoc(): Enter
287 10/10/2000 17:12:45.020 SEV=7 IPSECDBG/1 RPT=12
No USER filter configured
288 10/10/2000 17:12:45.020 SEV=9 IPSECDBG/1 RPT=13
KeyProcessUpdate: Enter
289 10/10/2000 17:12:45.020 SEV=8 IPSECDBG/1 RPT=14
KeyProcessUpdate: success
290 10/10/2000 17:12:45.020 SEV=8 IKEDBG/7 RPT=1
IKE got a KEY_ADD MSG for SA: SPI = 0x991518b4
291 10/10/2000 17:12:45.020 SEV=8 IKEDBG/0 RPT=51
pitcher: rcv KEY_UPDATE, spi 0x69bc69bd
Boa depuração com SDI
Depuração de SDI
Se bem-sucedida (primeira autenticação no SDI)
10/06/2000 11:57:04/U 37297304/vpn3000 000037297304/37297304 372 10/06/2000 11:57:04/L Node Secret Sent to Client zekie.cisco.com 10/06/2000 15:57:05/U 37297304/vpn3000 000037297304/37297304 372 10/06/2000 11:57:05/U PASSCODE Accepted zekie.cisco.com
Se bem-sucedido (após a primeira autenticação em SDI)
10/06/2000 16:06:09U 37297304/vpn3000 000037297304/37297304 372 10/06/2000 12:06:09L PASSCODE Accepted zekie.cisco.com
Depuração do VPN 3000 Concentrator (em teste)
Depurar "Nome da classe" para autenticação:
-
AUTH
-
AUTHDBG
-
CÓDIGO AUTOMÁTICO
4 10/06/2000 14:09:25.000 SEV=8 AUTHDBG/1 RPT=1 AUTH_Open() returns 14 5 10/06/2000 14:09:25.000 SEV=7 AUTH/12 RPT=1 Authentication session opened: handle = 14 6 10/06/2000 14:09:25.000 SEV=8 AUTHDBG/3 RPT=1 AUTH_PutAttrTable(14, 5a2aa0) 7 10/06/2000 14:09:25.000 SEV=8 AUTHDBG/5 RPT=1 AUTH_Authenticate(14, e5187e0, 306bdc) 8 10/06/2000 14:09:25.000 SEV=8 AUTHDBG/59 RPT=1 AUTH_BindServer(71e097c, 0, 0) 9 10/06/2000 14:09:25.000 SEV=9 AUTHDBG/69 RPT=1 Auth Server 649ab4 has been bound to ACB 71e097c, sessions = 1 10 10/06/2000 14:09:25.000 SEV=8 AUTHDBG/65 RPT=1 AUTH_CreateTimer(71e097c, 0, 0) 11 10/06/2000 14:09:25.000 SEV=9 AUTHDBG/72 RPT=1 Reply timer created: handle = 490011 12 10/06/2000 14:09:25.000 SEV=8 AUTHDBG/61 RPT=1 AUTH_BuildMsg(71e097c, 0, 0) 13 10/06/2000 14:09:25.000 SEV=8 AUTHDBG/51 RPT=1 Sdi_Build(71e097c) 14 10/06/2000 14:09:25.010 SEV=8 AUTHDBG/64 RPT=1 AUTH_StartTimer(71e097c, 0, 0) 15 10/06/2000 14:09:25.010 SEV=9 AUTHDBG/73 RPT=1 Reply timer started: handle = 490011, timestamp = 8553930, timeout = 4000 16 10/06/2000 14:09:25.010 SEV=8 AUTHDBG/62 RPT=1 AUTH_SndRequest(71e097c, 0, 0) 17 10/06/2000 14:09:25.010 SEV=8 AUTHDBG/52 RPT=1 Sdi_Xmt(71e097c) 18 10/06/2000 14:09:25.010 SEV=9 AUTHDBG/71 RPT=1 xmit_cnt = 1 19 10/06/2000 14:09:26.080 SEV=8 AUTHDBG/63 RPT=1 AUTH_RcvReply(71e097c, 0, 0) 20 10/06/2000 14:09:26.080 SEV=8 AUTHDBG/53 RPT=1 Sdi_Rcv(71e097c) 21 10/06/2000 14:09:26.080 SEV=8 AUTHDBG/66 RPT=1 AUTH_DeleteTimer(71e097c, 0, 0) 22 10/06/2000 14:09:26.080 SEV=9 AUTHDBG/74 RPT=1 Reply timer stopped: handle = 490011, timestamp = 8554037 23 10/06/2000 14:09:26.080 SEV=8 AUTHDBG/58 RPT=1 AUTH_Callback(71e097c, 0, 0) 24 10/06/2000 14:09:26.080 SEV=6 AUTH/4 RPT=1 Authentication successful: handle = 14, server = 172.18.124.99, user = 37297304 25 10/06/2000 14:09:26.080 SEV=8 AUTHDBG/2 RPT=1 AUTH_Close(14) 26 10/06/2000 14:09:26.080 SEV=8 AUTHDBG/60 RPT=1 AUTH_UnbindServer(71e097c, 0, 0) 27 10/06/2000 14:09:26.080 SEV=9 AUTHDBG/70 RPT=1 Auth Server 649ab4 has been unbound from ACB 71e097c, sessions = 0 28 10/06/2000 14:09:26.080 SEV=8 AUTHDBG/10 RPT=1 AUTH_Int_FreeAuthCB(71e097c) 29 10/06/2000 14:09:26.080 SEV=9 AUTHDBG/19 RPT=1 instance = 15, clone_instance = 0 30 10/06/2000 14:09:26.080 SEV=7 AUTH/13 RPT=1 Authentication session closed: handle = 14
Debugs ruins
Nome de usuário inválido ou usuário não ativado no cliente
Depuração de SDI
10/06/2000 16:30:21U junk/vpn3000 10/06/2000 12:30:21L User Not on Client zekie.cisco.com
Debug de VPN 3000
21 10/06/2000 14:20:06.310 SEV=3 AUTH/5 RPT=5 Authentication rejected: Reason = Unspecified handle = 15, server = 172.18.124.99, user = junk
Nome de usuário válido, senha inválido.
Depuração de SDI
10/06/2000 16:33:07U 37297304/vpn3000 000037297304/37297304 372 10/06/2000 12:33:07L ACCESS DENIED, PASSCODE Incorrect zekie.cisco.com
Debug de VPN 3000
249 10/06/2000 14:22:52.160 SEV=3 AUTH/5 RPT=6 Authentication rejected: Reason = Unspecified handle = 16, server = 172.18.124.99, user = 37297304
Servidor SDI inatingível ou daemon inativo.
Depuração de SDI
Não mostra nada (não recebeu o pedido)
Debug de VPN 3000
77 10/06/2000 14:28:55.600 SEV=4 AUTH/9 RPT=7 Authentication failed: Reason = Network error handle = 17, server = 172.18.124.99, user = 37297304
VPN 3000 não configurado como cliente na caixa SDI
Depuração de SDI
10/06/2000 17:37:42U --/172.18.124.134 -->/ 10/06/2000 13:36:42L Client Not Found zekie.cisco.com
Debug de VPN 3000
113 10/06/2000 15:26:27.440 SEV=3 AUTH/5 RPT=8 Authentication rejected: Reason = Unspecified handle = 21, server = 172.18.124.99, user = 37297304
VPN 3000 Concentrator removido como um cliente do servidor SDI e, em seguida, adicionado novamente
O servidor SDI tentou enviar o arquivo SECURID para substituir o antigo, mas o VPN 3000 já tinha esse arquivo.
Mensagem em SDI
10/06/2000 13:42:18L Node Verification Failed zekie.cisco.com
Debug de VPN 3000
21 10/06/2000 15:32:03.030 SEV=3 AUTH/5 RPT=9 Authentication rejected: Reason = Unspecified handle = 22, server = 172.18.124.99, user = 37297304
Para solucionar esse problema, exclua o arquivo SECURID no concentrador VPN 3000 por meio de Administration > File management > Files > SECURID > Delete. Ao testar novamente, o VPN 3000 Concentrator aceita o novo arquivo do servidor SDI. Se a caixa de seleção Editar Cliente > Enviar Nó Secreto estiver indisponível na SDI, o servidor da SDI não conseguiu concluir a troca. Quando o Concentrador VPN 3000 tiver o arquivo SECURID, a caixa de seleção Sent Node Secret (Segredo de Nó Enviado) ficará marcada/não acinzentada.
Informações Relacionadas
Histórico de revisões
| Revisão | Data de publicação | Comentários |
|---|---|---|
1.0 |
14-Jan-2008 |
Versão inicial |
FeedbackContate a Cisco
- Abrir um caso de suporte
- (É necessário um Contrato de Serviço da Cisco)