IPSec com cliente VPN (endereço IP atribuído estático/dinâmico) para exemplo de configuração do VPN 3000 Concentrator

Introduction

Esta configuração de exemplo demonstra como formar um túnel IPsec de um PC que executa o Cisco VPN Client (4.x e posterior) (endereço IP atribuído estático/dinâmico) para um Cisco VPN 3000 Concentrator para permitir que o usuário acesse com segurança a rede dentro do VPN Concentrator.

Consulte Utilização do Cisco Secure ACS para Windows com o VPN 3000 Concentrator - IPSec para saber mais sobre o mesmo cenário com a autenticação RADIUS usando o Cisco ACS. Consulte Configurando o Cisco VPN 3000 Concentrator com MS RADIUS para saber mais sobre o mesmo cenário com a autenticação MS-RADIUS.

Prerequisites

Requirements

Não existem requisitos específicos para este documento.

Componentes Utilizados

As informações neste documento são baseadas nestas versões de software e hardware:

• Cisco VPN 3030 Concentrator versão 4.1.7.A

• Cisco VPN Client versão 4.x e posterior

Observação: essa configuração foi testada novamente recentemente usando o Cisco VPN Concentrator versão 4.7.2.H.

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Diagrama de Rede

Este documento utiliza a seguinte configuração de rede:

Observação: os esquemas de endereçamento IP usados nesta configuração não são legalmente roteáveis na Internet. São endereços RFC 1918 usados em um ambiente de laboratório.

Conventions

Consulte as Convenções de Dicas Técnicas da Cisco para obter mais informações sobre convenções de documentos.

Configurar o VPN 3000 Concentrator

Conclua estes passos para configurar o VPN 3000 Concentrator.

Observação: devido a limitações de espaço, algumas capturas de tela mostram apenas telas parciais.

1. Conecte-se à porta do console do VPN Concentrator e verifique se há endereços IP atribuídos às interfaces privada (interna) e pública (externa).

   Além disso, verifique se há um gateway padrão atribuído para que o VPN Concentrator possa encaminhar os pacotes para os destinos que ele não conhece para o gateway padrão (normalmente o Internet Gateway Router):

   

   

   Esta tabela mostra os endereços IP atuais.

   

   

   

   

2. Escolha a opção de filtro Público para a interface Pública.

   

3. Aponte um navegador para a interface interna do VPN Concentrator e escolha Configuration > System > Address Management > Address Pools > Add para atribuir um intervalo disponível de endereços IP.

   Especifique uma faixa de endereços IP que não entrem em conflito com nenhum outro dispositivo na rede interna:

   Observação: essas capturas de tela mostram o gerenciamento de interface público externo porque foram adicionados filtros para permitir isso somente em uma configuração de laboratório.

   

4. Escolha Configuration > System > Address Management > Assignment, marque a caixa Use Address Pools e clique em Apply para informar ao VPN Concentrator para usar o pool.

   

5. Escolha Configuration > User Management > Groups > Add Group para configurar um grupo IPsec para os usuários e definir um nome de grupo e uma senha.

   Este exemplo usa group="ipsecgroup" com password/verify="cisco123":

   

6. Na guia Geral do grupo, verifique se IPSec está selecionado.

   

7. Na guia IPSec do grupo, verifique se a autenticação está definida como Interno. Escolha Configuration > User Management > Groups > Modify Group e selecione ipsecgroup na opção Current Groups para fazer isso.

   

8. Escolha Configuration > User Management > Users > Add e adicione um usuário ao grupo definido anteriormente.

   Neste exemplo, o usuário é "ipsecuser" com a senha "xyz12345" no grupo "ipsecgroup":

   

Atribuir um endereço IP estático a um usuário

Para atribuir um endereço IP estático para o usuário VPN remoto toda vez que se conectar ao VPN 3000 Series Concentrator, escolha Configuration > User Management > Users > Modify ipsecuser2 > identity. Nesta configuração para o usuário (ipsecuser2), o endereço IP estático 10.2.2.1/24 é atribuído sempre que o usuário se conecta.

Observação: certifique-se de ir para Configuration > System > Address Management > Assignment para garantir que o VPN Concentrator provisione o endereço IP atribuído. Marque Usar endereço do servidor de autenticação para atribuir endereços IP recuperados de um servidor de autenticação por usuário. O endereço IP e a máscara de sub-rede inseridos na guia Parâmetros de Identidade na janela Gerenciamento de Usuário > Usuários > Adicionar ou Modificar é considerado como estando no servidor de autenticação interno.

Configurar o VPN Client

Conclua estes passos para configurar o VPN Client.

1. Clique em New para criar uma nova entrada de conexão.

   

2. Nomeie a conexão, insira o endereço IP da interface pública do VPN Concentrator e forneça as credenciais do grupo. Nesse caso, o nome é ipsecgroup e a senha é cisco123. Clique em Salvar quando terminar.

   

3. Selecione a entrada da ligação na lista e clique em Ligar. Quando for solicitado o nome de usuário/senha, digite seu nome de usuário/senha.

   

Verificar

No momento, não há procedimento de verificação disponível para esta configuração.

Troubleshoot

Essas seções fornecem informações que você pode usar para solucionar problemas de sua configuração.

A Output Interpreter Tool ( somente clientes registrados) (OIT) oferece suporte a determinados comandos show. Use a OIT para exibir uma análise da saída do comando show.

Nota:Consulte Informações Importantes sobre Comandos de Depuração antes de usar os comandos debug.

que pode dar errado

Esses são possíveis erros que podem ocorrer. Consulte as seções VPN Client e VPN Concentrator para obter as resoluções para esses erros.

• Um usuário recebe a mensagem Unable to negotiation IPSec or host did not response.

  A depuração do VPN 3000 mostra:

  14 02/20/2001 08:59:29.100 SEV=4 IKE/22 RPT=5 10.102.55.139
  No Group found matching badgroup for Pre-shared key peer 10.102.55.139

  Causa normal: O usuário tenta se conectar com um nome de grupo que não está configurado.

• Um usuário não pode se conectar e a depuração do VPN 3000 mostra:

  Filter missing on interface 2, IKE data from Peer x.x.x.x dropped

  Causa normal: O filtro está ausente na interface pública. Geralmente é o filtro "público" (mas pode ser o filtro privado); "none" não é válido). Escolha Configuration > Interfaces > Ethernet 2 > Filter e torne o filtro "público" ou outro valor (ou seja, não "nenhum"). Consulte a seção de configuração deste documento para obter mais informações sobre como configurar o filtro.

• Um usuário não pode se conectar e não pode negociar IPSec ou o host não respondeu.

  A depuração do VPN 3000 mostra:

  Terminating connection attempt: IPSEC not permitted for group >group<

  Causa normal: O IPsec não está selecionado no grupo. Escolha Configuration > User Management > Groups > <group> > Modify > General e verifique se IPSec está selecionado em Tunneling Protocols.

• Um usuário não pode se conectar após várias tentativas e vê Falha na autenticação do usuário.

  A depuração do VPN 3000 mostra:

  Authentication rejected: Reason = User was not found handle = 14, server = Internal, 
  user = <user>

  Causa normal: O usuário não existe no banco de dados de usuário. Certifique-se de inserir o nome de usuário correto quando a janela de autenticação do usuário for exibida.

• Os usuários não podem se conectar e a depuração do VPN 3000 mostra:

  Filter missing on interface 0, IKE data from Peer x.x.x.x dropped

  Causa normal: A rota padrão está ausente. Verifique se há uma rota padrão na configuração. Escolha Configuration > System > IP routing > Default Gateway e especifique o gateway padrão.

• Um usuário não pode se conectar e vê que sua conexão IPSec foi encerrada pelo peer remoto.

  A depuração do VPN 3000 mostra:

   User [ <user> ]
  IKE rcv'd FAILED IP Addr status!

  Causa normal: Não há opção marcada para fornecer um endereço IP ao VPN Client. Escolha Configuration > System > Address Management > Address Assignment e selecione uma opção.

• Um usuário não pode se conectar e vê falha na autenticação do usuário.

  A depuração do VPN 3000 mostra:

  The calculated HASH doesn't match the received value

  Causa normal: A senha do grupo no VPN Client é diferente da senha configurada no VPN Concentrator. Verifique a senha no VPN Client e no Concentrator.

• Você configurou o pool VPN para os recursos por trás do VPN Concentrator. Você pode acessar os recursos, mas não pode fazer ping neles.

  Causa normal: Há um PIX atrás do VPN Concentrator que bloqueia os pacotes ICMP. Faça login nesse PIX e aplique uma lista de acesso para ativar pacotes ICMP.

• Não há depurações do VPN Concentrator e todos ou alguns usuários não podem se conectar.

  O filtro público padrão do VPN Concentrator contém regras para permitir esse tráfego:

  • Protocolo = UDP, porta = 500

  • Protocolo = UDP, porta = 10000

  • Protocolo = ESP

  • Protocolo = AH

  Se os filtros do VPN Concentrator permitirem esse tráfego, um dispositivo entre o VPN Client e o VPN Concentrator poderá estar bloqueando algumas dessas portas (talvez um firewall). Para verificar, tente se conectar ao VPN Concentrator da rede imediatamente fora do VPN Concentrator. Se isso funcionar, um dispositivo entre o VPN Client PC e o VPN Concentrator está bloqueando o tráfego.

• Um usuário não pode se conectar e vê estes registros:

  07/10/2006 11:48:59.280 SEV=4 IKE/0 RPT=141 10.86.190.92 
  Group [NYMVPN]
  received an unencrypted packet when crypto active!! Dropping packet

  Causa normal: Um nome ou senha de grupo definido incorretamente. Recrie o novo nome de grupo e senha no VPN 3000 Concentrator para o VPN Client.

• Um usuário pode fazer ping ou executar telnet para um host atrás do VPN Concentrator, mas o usuário não pode usar o Remote Desktop 9RDP) ou aplicativos semelhantes.

  Causa comum:O filtro Público não está ativado na interface Pública. Consulte a etapa 2 na seção Configurar o VPN 3000 Concentrator deste documento.

• Um usuário pode se conectar, mas nenhum tráfego passa pelo túnel VPN.

  Causa normal: NAT-Transparency não está habilitado. Em muitos casos, o VPN Client está por trás de um dispositivo PAT. O PAT depende dos números de porta TCP e UDP para conservar espaço de endereço. Mas o ESP, que encapsula o tráfego VPN, é um protocolo separado do TCP ou do UDP. Isso significa que muitos dispositivos PAT não podem lidar com o tráfego ESP. O NAT-T encapsula pacotes ESP em pacotes UDP, permitindo que eles passem facilmente por um dispositivo PAT. Assim, para permitir que o tráfego ESP flua através de um dispositivo PAT, você precisa ativar o NAT-T no concentrador. Consulte Configurando o modo transparente de NAT para IPSec no VPN 3000 Concentrator para obter mais informações.

Cliente de VPN

Escolha Iniciar > Programas > Cisco Systems VPN 3000 Client > Log Viewer para exibir o log viewer.

Concentrador de VPN

Escolha Configuration > System > Events > Classes para ativar essa depuração se houver falhas de conexão de eventos:

• AUTH - Gravidade para registro 1-13

• AUTHDBG - Gravidade para registro 1-13

• IKE - Gravidade para registro 1-13

• IKEDBG - Gravidade para registro 1-13

• IPSEC - Gravidade para registro 1-13

• IPSECDBG - Gravidade para registro 1-13

Observação: se necessário, AUTHDECODE, IKEDECODE, IPSECDECODE podem ser adicionados posteriormente.

Consulte Troubleshooting de Problemas de Conexão no VPN 3000 Concentrator para obter mais detalhes sobre a solução de problemas.

Escolha Monitoring > Filterable Event Log para exibir o log.

VPN 3000 Concentrator – Exemplo adequado de depuração

1 02/07/2002 08:00:13.320 SEV=8 IKEDBG/0 RPT=69 172.18.124.241 
RECEIVED Message (msgid=0) with payloads : 
HDR + SA (1) + KE (4) + NONCE (10) + ID (5) + VENDOR (13) + VENDOR (13) + VENDOR
 (13) + NONE (0) ... total length : 562

4 02/07/2002 08:00:13.320 SEV=9 IKEDBG/0 RPT=70 172.18.124.241 
processing SA payload

5 02/07/2002 08:00:13.320 SEV=9 IKEDBG/0 RPT=71 172.18.124.241 
processing ke payload

6 02/07/2002 08:00:13.320 SEV=9 IKEDBG/0 RPT=72 172.18.124.241 
processing ISA_KE

7 02/07/2002 08:00:13.320 SEV=9 IKEDBG/1 RPT=7 172.18.124.241 
processing nonce payload

8 02/07/2002 08:00:13.320 SEV=9 IKEDBG/1 RPT=8 172.18.124.241 
Processing ID

9 02/07/2002 08:00:13.320 SEV=9 IKEDBG/47 RPT=4 172.18.124.241 
processing VID payload

10 02/07/2002 08:00:13.320 SEV=9 IKEDBG/49 RPT=4 172.18.124.241 
Received xauth V6 VID

11 02/07/2002 08:00:13.320 SEV=9 IKEDBG/47 RPT=5 172.18.124.241 
processing VID payload

12 02/07/2002 08:00:13.320 SEV=9 IKEDBG/49 RPT=5 172.18.124.241 
Received DPD VID

13 02/07/2002 08:00:13.320 SEV=9 IKEDBG/47 RPT=6 172.18.124.241 
processing VID payload

14 02/07/2002 08:00:13.320 SEV=9 IKEDBG/49 RPT=6 172.18.124.241 
Received Cisco Unity client VID

15 02/07/2002 08:00:13.320 SEV=9 IKEDBG/23 RPT=2 172.18.124.241 
Starting group lookup for peer 172.18.124.241

16 02/07/2002 08:00:13.320 SEV=8 AUTHDBG/1 RPT=2 
AUTH_Open() returns 136

17 02/07/2002 08:00:13.320 SEV=7 AUTH/12 RPT=2 
Authentication session opened: handle = 136

18 02/07/2002 08:00:13.320 SEV=8 AUTHDBG/3 RPT=2 
AUTH_PutAttrTable(136, 728a84)

19 02/07/2002 08:00:13.320 SEV=8 AUTHDBG/6 RPT=2 
AUTH_GroupAuthenticate(136, 9b143bc, 482fb0)

20 02/07/2002 08:00:13.320 SEV=8 AUTHDBG/59 RPT=2 
AUTH_BindServer(9a08630, 0, 0)

21 02/07/2002 08:00:13.320 SEV=9 AUTHDBG/69 RPT=2 
Auth Server 16b3fa0 has been bound to ACB 9a08630, sessions = 1

22 02/07/2002 08:00:13.320 SEV=8 AUTHDBG/65 RPT=2 
AUTH_CreateTimer(9a08630, 0, 0)

23 02/07/2002 08:00:13.320 SEV=9 AUTHDBG/72 RPT=2 
Reply timer created: handle = 3B2001B

24 02/07/2002 08:00:13.320 SEV=8 AUTHDBG/61 RPT=2 
AUTH_BuildMsg(9a08630, 0, 0)

25 02/07/2002 08:00:13.320 SEV=8 AUTHDBG/64 RPT=2 
AUTH_StartTimer(9a08630, 0, 0)

26 02/07/2002 08:00:13.320 SEV=9 AUTHDBG/73 RPT=2 
Reply timer started: handle = 3B2001B, timestamp = 10085308, timeout = 30000

27 02/07/2002 08:00:13.320 SEV=8 AUTHDBG/62 RPT=2 
AUTH_SndRequest(9a08630, 0, 0)

28 02/07/2002 08:00:13.320 SEV=8 AUTHDBG/50 RPT=3 
IntDB_Decode(62b6d00, 115)

29 02/07/2002 08:00:13.320 SEV=8 AUTHDBG/47 RPT=3 
IntDB_Xmt(9a08630)

30 02/07/2002 08:00:13.320 SEV=9 AUTHDBG/71 RPT=2 
xmit_cnt = 1

31 02/07/2002 08:00:13.320 SEV=8 AUTHDBG/47 RPT=4 
IntDB_Xmt(9a08630)

32 02/07/2002 08:00:13.420 SEV=8 AUTHDBG/49 RPT=2 
IntDB_Match(9a08630, 2ebe71c)

33 02/07/2002 08:00:13.420 SEV=8 AUTHDBG/63 RPT=2 
AUTH_RcvReply(9a08630, 0, 0)

34 02/07/2002 08:00:13.420 SEV=8 AUTHDBG/50 RPT=4 
IntDB_Decode(2ebe71c, 44)

35 02/07/2002 08:00:13.420 SEV=8 AUTHDBG/48 RPT=2 
IntDB_Rcv(9a08630)

36 02/07/2002 08:00:13.420 SEV=8 AUTHDBG/66 RPT=2 
AUTH_DeleteTimer(9a08630, 0, 0)

37 02/07/2002 08:00:13.420 SEV=9 AUTHDBG/74 RPT=2 
Reply timer stopped: handle = 3B2001B, timestamp = 10085318

38 02/07/2002 08:00:13.420 SEV=8 AUTHDBG/58 RPT=2 
AUTH_Callback(9a08630, 0, 0)

39 02/07/2002 08:00:13.420 SEV=6 AUTH/41 RPT=2 172.18.124.241 
Authentication successful: handle = 136, server = Internal, group = ipsecgroup

40 02/07/2002 08:00:13.420 SEV=7 IKEDBG/0 RPT=73 172.18.124.241 
Group [ipsecgroup]
Found Phase 1 Group (ipsecgroup)

41 02/07/2002 08:00:13.420 SEV=8 AUTHDBG/4 RPT=2 
AUTH_GetAttrTable(136, 728c4c)

42 02/07/2002 08:00:13.420 SEV=7 IKEDBG/14 RPT=2 172.18.124.241 
Group [ipsecgroup]
Authentication configured for Internal

43 02/07/2002 08:00:13.420 SEV=8 AUTHDBG/2 RPT=2 
AUTH_Close(136)

44 02/07/2002 08:00:13.420 SEV=9 IKEDBG/0 RPT=74 172.18.124.241 
Group [ipsecgroup]
processing IKE SA

45 02/07/2002 08:00:13.420 SEV=8 IKEDBG/0 RPT=75 172.18.124.241 
Group [ipsecgroup]
Proposal # 1, Transform # 1, Type ISAKMP, Id IKE
Parsing received transform:
  Phase 1 failure against global IKE proposal # 1:
  Mismatched attr types for class Hash Alg:
    Rcv'd: SHA
    Cfg'd: MD5

50 02/07/2002 08:00:13.420 SEV=8 IKEDBG/0 RPT=76 172.18.124.241 
Group [ipsecgroup]
  Phase 1 failure against global IKE proposal # 2:
  Mismatched attr types for class Hash Alg:
    Rcv'd: SHA
    Cfg'd: MD5

53 02/07/2002 08:00:13.420 SEV=8 IKEDBG/0 RPT=77 172.18.124.241 
Group [ipsecgroup]
  Phase 1 failure against global IKE proposal # 3:
  Mismatched attr types for class DH Group:
    Rcv'd: Oakley Group 2
    Cfg'd: Oakley Group 1

57 02/07/2002 08:00:13.420 SEV=8 IKEDBG/0 RPT=78 172.18.124.241 
Group [ipsecgroup]
  Phase 1 failure against global IKE proposal # 4:
  Mismatched attr types for class DH Group:
    Rcv'd: Oakley Group 2
    Cfg'd: Oakley Group 1

61 02/07/2002 08:00:13.420 SEV=8 IKEDBG/0 RPT=79 172.18.124.241 
Group [ipsecgroup]
  Phase 1 failure against global IKE proposal # 5:
  Mismatched attr types for class DH Group:
    Rcv'd: Oakley Group 2
    Cfg'd: Oakley Group 7

65 02/07/2002 08:00:13.420 SEV=8 IKEDBG/0 RPT=80 172.18.124.241 
Group [ipsecgroup]
  Phase 1 failure against global IKE proposal # 6:
  Mismatched attr types for class Hash Alg:
    Rcv'd: SHA
    Cfg'd: MD5

68 02/07/2002 08:00:13.420 SEV=7 IKEDBG/28 RPT=2 172.18.124.241 
Group [ipsecgroup]
IKE SA Proposal # 1, Transform # 2 acceptable
Matches global IKE entry # 1

70 02/07/2002 08:00:13.420 SEV=8 AUTHDBG/60 RPT=2 
AUTH_UnbindServer(9a08630, 0, 0)

71 02/07/2002 08:00:13.420 SEV=9 AUTHDBG/70 RPT=2 
Auth Server 16b3fa0 has been unbound from ACB 9a08630, sessions = 0

72 02/07/2002 08:00:13.420 SEV=8 AUTHDBG/10 RPT=2 
AUTH_Int_FreeAuthCB(9a08630)

73 02/07/2002 08:00:13.420 SEV=7 AUTH/13 RPT=2 
Authentication session closed: handle = 136

74 02/07/2002 08:00:13.450 SEV=9 IKEDBG/0 RPT=81 172.18.124.241 

Group [ipsecgroup]
constructing ISA_SA for isakmp

75 02/07/2002 08:00:13.450 SEV=9 IKEDBG/0 RPT=82 172.18.124.241 
Group [ipsecgroup]
constructing ke payload

76 02/07/2002 08:00:13.450 SEV=9 IKEDBG/1 RPT=9 172.18.124.241 
Group [ipsecgroup]
constructing nonce payload

77 02/07/2002 08:00:13.450 SEV=9 IKEDBG/0 RPT=83 172.18.124.241 
Group [ipsecgroup]
Generating keys for Responder...

78 02/07/2002 08:00:13.450 SEV=9 IKEDBG/1 RPT=10 172.18.124.241 
Group [ipsecgroup]
constructing ID

79 02/07/2002 08:00:13.450 SEV=9 IKEDBG/0 RPT=84 
Group [ipsecgroup]
construct hash payload

80 02/07/2002 08:00:13.450 SEV=9 IKEDBG/0 RPT=85 172.18.124.241 
Group [ipsecgroup]
computing hash

81 02/07/2002 08:00:13.450 SEV=9 IKEDBG/46 RPT=5 172.18.124.241 
Group [ipsecgroup]
constructing Cisco Unity VID payload

82 02/07/2002 08:00:13.450 SEV=9 IKEDBG/46 RPT=6 172.18.124.241 
Group [ipsecgroup]
constructing xauth V6 VID payload

83 02/07/2002 08:00:13.450 SEV=9 IKEDBG/46 RPT=7 172.18.124.241 
Group [ipsecgroup]
constructing dpd vid payload

84 02/07/2002 08:00:13.450 SEV=9 IKEDBG/46 RPT=8 172.18.124.241 
Group [ipsecgroup]
constructing VID payload

85 02/07/2002 08:00:13.450 SEV=9 IKEDBG/48 RPT=2 172.18.124.241 
Group [ipsecgroup]
Send Altiga GW VID

86 02/07/2002 08:00:13.450 SEV=8 IKEDBG/0 RPT=86 172.18.124.241 
SENDING Message (msgid=0) with payloads : 
HDR + SA (1) + KE (4) + NONCE (10) + ID (5) + HASH (8) + VENDOR (13) + VENDOR (1
3) + VENDOR (13) + VENDOR (13) + NONE (0) ... total length : 344

89 02/07/2002 08:00:13.480 SEV=8 IKEDBG/0 RPT=87 172.18.124.241 
RECEIVED Message (msgid=0) with payloads : 
HDR + HASH (8) + NOTIFY (11) + NONE (0) ... total length : 76

91 02/07/2002 08:00:13.480 SEV=9 IKEDBG/0 RPT=88 172.18.124.241 
Group [ipsecgroup]
processing hash

92 02/07/2002 08:00:13.480 SEV=9 IKEDBG/0 RPT=89 172.18.124.241 
Group [ipsecgroup]
computing hash

93 02/07/2002 08:00:13.480 SEV=9 IKEDBG/0 RPT=90 172.18.124.241 
Group [ipsecgroup]
Processing Notify payload

94 02/07/2002 08:00:13.480 SEV=9 IKEDBG/0 RPT=91 172.18.124.241 
Group [ipsecgroup]
constructing blank hash

95 02/07/2002 08:00:13.480 SEV=9 IKEDBG/0 RPT=92 172.18.124.241 
Group [ipsecgroup]
constructing qm hash

96 02/07/2002 08:00:13.480 SEV=8 IKEDBG/0 RPT=93 172.18.124.241 
SENDING Message (msgid=ec88ba81) with payloads : 
HDR + HASH (8) + ATTR (14) + NONE (0) ... total length : 100

98 02/07/2002 08:00:21.810 SEV=8 IKEDBG/0 RPT=94 172.18.124.241 
RECEIVED Message (msgid=ec88ba81) with payloads : 
HDR + HASH (8) + ATTR (14) + NONE (0) ... total length : 85

100 02/07/2002 08:00:21.810 SEV=9 IKEDBG/1 RPT=11 
process_attr(): Enter!

101 02/07/2002 08:00:21.810 SEV=9 IKEDBG/1 RPT=12 
Processing MODE_CFG Reply attributes.

102 02/07/2002 08:00:21.810 SEV=8 AUTHDBG/1 RPT=3 
AUTH_Open() returns 137

103 02/07/2002 08:00:21.810 SEV=7 AUTH/12 RPT=3 
Authentication session opened: handle = 137

104 02/07/2002 08:00:21.810 SEV=8 AUTHDBG/3 RPT=3 
AUTH_PutAttrTable(137, 728a84)

105 02/07/2002 08:00:21.810 SEV=8 AUTHDBG/5 RPT=1 
AUTH_Authenticate(137, 50093bc, 4b5708)

106 02/07/2002 08:00:21.810 SEV=8 AUTHDBG/59 RPT=3 
AUTH_BindServer(9b1544c, 0, 0)

107 02/07/2002 08:00:21.810 SEV=9 AUTHDBG/69 RPT=3 
Auth Server 16b3fa0 has been bound to ACB 9b1544c, sessions = 1

108 02/07/2002 08:00:21.810 SEV=8 AUTHDBG/65 RPT=3 
AUTH_CreateTimer(9b1544c, 0, 0)

109 02/07/2002 08:00:21.810 SEV=9 AUTHDBG/72 RPT=3 
Reply timer created: handle = 3B4001A

110 02/07/2002 08:00:21.810 SEV=8 AUTHDBG/61 RPT=3 
AUTH_BuildMsg(9b1544c, 0, 0)

111 02/07/2002 08:00:21.810 SEV=8 AUTHDBG/64 RPT=3 
AUTH_StartTimer(9b1544c, 0, 0)

112 02/07/2002 08:00:21.810 SEV=9 AUTHDBG/73 RPT=3 
Reply timer started: handle = 3B4001A, timestamp = 10086157, timeout = 30000

113 02/07/2002 08:00:21.810 SEV=8 AUTHDBG/62 RPT=3 
AUTH_SndRequest(9b1544c, 0, 0)

114 02/07/2002 08:00:21.810 SEV=8 AUTHDBG/50 RPT=5 
IntDB_Decode(62b6d00, 102)

115 02/07/2002 08:00:21.810 SEV=8 AUTHDBG/47 RPT=5 
IntDB_Xmt(9b1544c)

116 02/07/2002 08:00:21.810 SEV=9 AUTHDBG/71 RPT=3 
xmit_cnt = 1

117 02/07/2002 08:00:21.810 SEV=8 AUTHDBG/47 RPT=6 
IntDB_Xmt(9b1544c)

118 02/07/2002 08:00:21.910 SEV=8 AUTHDBG/49 RPT=3 
IntDB_Match(9b1544c, 2ebe71c)

119 02/07/2002 08:00:21.910 SEV=8 AUTHDBG/63 RPT=3 
AUTH_RcvReply(9b1544c, 0, 0)

120 02/07/2002 08:00:21.910 SEV=8 AUTHDBG/50 RPT=6 
IntDB_Decode(2ebe71c, 62)

121 02/07/2002 08:00:21.910 SEV=8 AUTHDBG/48 RPT=3 
IntDB_Rcv(9b1544c)

122 02/07/2002 08:00:21.910 SEV=8 AUTHDBG/66 RPT=3 
AUTH_DeleteTimer(9b1544c, 0, 0)

123 02/07/2002 08:00:21.910 SEV=9 AUTHDBG/74 RPT=3 
Reply timer stopped: handle = 3B4001A, timestamp = 10086167

124 02/07/2002 08:00:21.910 SEV=8 AUTHDBG/58 RPT=3 
AUTH_Callback(9b1544c, 0, 0)

125 02/07/2002 08:00:21.910 SEV=6 AUTH/4 RPT=1 172.18.124.241 
Authentication successful: handle = 137, server = Internal, user = ipsecuser

126 02/07/2002 08:00:21.910 SEV=8 AUTHDBG/3 RPT=4 
AUTH_PutAttrTable(137, 1861c60)

127 02/07/2002 08:00:21.910 SEV=8 AUTHDBG/60 RPT=3 
AUTH_UnbindServer(9b1544c, 0, 0)

128 02/07/2002 08:00:21.910 SEV=9 AUTHDBG/70 RPT=3 
Auth Server 16b3fa0 has been unbound from ACB 9b1544c, sessions = 0

129 02/07/2002 08:00:21.910 SEV=8 AUTHDBG/59 RPT=4 
AUTH_BindServer(9b1544c, 0, 0)

130 02/07/2002 08:00:21.910 SEV=9 AUTHDBG/69 RPT=4 
Auth Server 16b3fa0 has been bound to ACB 9b1544c, sessions = 1

131 02/07/2002 08:00:21.910 SEV=8 AUTHDBG/65 RPT=4 
AUTH_CreateTimer(9b1544c, 0, 0)

132 02/07/2002 08:00:21.910 SEV=9 AUTHDBG/72 RPT=4 
Reply timer created: handle = 3B5001A

133 02/07/2002 08:00:21.910 SEV=8 AUTHDBG/61 RPT=4 
AUTH_BuildMsg(9b1544c, 0, 0)

134 02/07/2002 08:00:21.910 SEV=8 AUTHDBG/64 RPT=4 
AUTH_StartTimer(9b1544c, 0, 0)

135 02/07/2002 08:00:21.910 SEV=9 AUTHDBG/73 RPT=4 
Reply timer started: handle = 3B5001A, timestamp = 10086167, timeout = 30000

136 02/07/2002 08:00:21.910 SEV=8 AUTHDBG/62 RPT=4 
AUTH_SndRequest(9b1544c, 0, 0)

137 02/07/2002 08:00:21.910 SEV=8 AUTHDBG/50 RPT=7 
IntDB_Decode(2ec5350, 44)


138 02/07/2002 08:00:21.910 SEV=8 AUTHDBG/47 RPT=7 
IntDB_Xmt(9b1544c)

139 02/07/2002 08:00:21.910 SEV=9 AUTHDBG/71 RPT=4 
xmit_cnt = 1

140 02/07/2002 08:00:21.910 SEV=8 AUTHDBG/47 RPT=8 
IntDB_Xmt(9b1544c)

141 02/07/2002 08:00:22.010 SEV=8 AUTHDBG/49 RPT=4 
IntDB_Match(9b1544c, 2ec3f64)

142 02/07/2002 08:00:22.010 SEV=8 AUTHDBG/63 RPT=4 
AUTH_RcvReply(9b1544c, 0, 0)

143 02/07/2002 08:00:22.010 SEV=8 AUTHDBG/50 RPT=8 
IntDB_Decode(2ec3f64, 44)

144 02/07/2002 08:00:22.010 SEV=8 AUTHDBG/48 RPT=4 
IntDB_Rcv(9b1544c)

145 02/07/2002 08:00:22.010 SEV=8 AUTHDBG/66 RPT=4 
AUTH_DeleteTimer(9b1544c, 0, 0)

146 02/07/2002 08:00:22.010 SEV=9 AUTHDBG/74 RPT=4 
Reply timer stopped: handle = 3B5001A, timestamp = 10086177

147 02/07/2002 08:00:22.010 SEV=8 AUTHDBG/58 RPT=4 
AUTH_Callback(9b1544c, 0, 0)

148 02/07/2002 08:00:22.010 SEV=6 AUTH/41 RPT=3 172.18.124.241 
Authentication successful: handle = 137, server = Internal, group = ipsecgroup

149 02/07/2002 08:00:22.010 SEV=8 AUTHDBG/3 RPT=5 
AUTH_PutAttrTable(137, 1861c60)

150 02/07/2002 08:00:22.010 SEV=8 AUTHDBG/60 RPT=4 
AUTH_UnbindServer(9b1544c, 0, 0)

151 02/07/2002 08:00:22.010 SEV=9 AUTHDBG/70 RPT=4 
Auth Server 16b3fa0 has been unbound from ACB 9b1544c, sessions = 0

152 02/07/2002 08:00:22.010 SEV=8 AUTHDBG/59 RPT=5 
AUTH_BindServer(9b1544c, 0, 0)

153 02/07/2002 08:00:22.010 SEV=9 AUTHDBG/69 RPT=5 
Auth Server 16b3fa0 has been bound to ACB 9b1544c, sessions = 1

154 02/07/2002 08:00:22.010 SEV=8 AUTHDBG/65 RPT=5 
AUTH_CreateTimer(9b1544c, 0, 0)

155 02/07/2002 08:00:22.010 SEV=9 AUTHDBG/72 RPT=5 
Reply timer created: handle = 3B6001A

156 02/07/2002 08:00:22.010 SEV=8 AUTHDBG/61 RPT=5 
AUTH_BuildMsg(9b1544c, 0, 0)

157 02/07/2002 08:00:22.010 SEV=8 AUTHDBG/64 RPT=5 
AUTH_StartTimer(9b1544c, 0, 0)

158 02/07/2002 08:00:22.010 SEV=9 AUTHDBG/73 RPT=5 
Reply timer started: handle = 3B6001A, timestamp = 10086177, timeout = 30000

159 02/07/2002 08:00:22.010 SEV=8 AUTHDBG/62 RPT=5 
AUTH_SndRequest(9b1544c, 0, 0)

160 02/07/2002 08:00:22.010 SEV=8 AUTHDBG/50 RPT=9 
IntDB_Decode(2ec39ec, 44)

161 02/07/2002 08:00:22.010 SEV=8 AUTHDBG/47 RPT=9 
IntDB_Xmt(9b1544c)

162 02/07/2002 08:00:22.010 SEV=9 AUTHDBG/71 RPT=5 
xmit_cnt = 1

163 02/07/2002 08:00:22.010 SEV=8 AUTHDBG/47 RPT=10 
IntDB_Xmt(9b1544c)

164 02/07/2002 08:00:22.110 SEV=8 AUTHDBG/49 RPT=5 
IntDB_Match(9b1544c, 2ec5350)

165 02/07/2002 08:00:22.110 SEV=8 AUTHDBG/63 RPT=5 
AUTH_RcvReply(9b1544c, 0, 0)

166 02/07/2002 08:00:22.110 SEV=8 AUTHDBG/50 RPT=10 
IntDB_Decode(2ec5350, 44)

167 02/07/2002 08:00:22.110 SEV=8 AUTHDBG/48 RPT=5 
IntDB_Rcv(9b1544c)

168 02/07/2002 08:00:22.110 SEV=8 AUTHDBG/66 RPT=5 
AUTH_DeleteTimer(9b1544c, 0, 0)

169 02/07/2002 08:00:22.110 SEV=9 AUTHDBG/74 RPT=5 
Reply timer stopped: handle = 3B6001A, timestamp = 10086187

170 02/07/2002 08:00:22.110 SEV=8 AUTHDBG/58 RPT=5 
AUTH_Callback(9b1544c, 0, 0)

171 02/07/2002 08:00:22.110 SEV=6 AUTH/41 RPT=4 172.18.124.241 
Authentication successful: handle = 137, server = Internal, group = ipsecgroup

172 02/07/2002 08:00:22.110 SEV=8 AUTHDBG/4 RPT=3 
AUTH_GetAttrTable(137, 729c04)

173 02/07/2002 08:00:22.110 SEV=8 AUTHDBG/4 RPT=4 
AUTH_GetAttrTable(137, 728c4c)

174 02/07/2002 08:00:22.110 SEV=7 IKEDBG/14 RPT=3 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Authentication configured for Internal

175 02/07/2002 08:00:22.110 SEV=8 AUTHDBG/2 RPT=3 
AUTH_Close(137)

176 02/07/2002 08:00:22.110 SEV=4 IKE/52 RPT=61 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
User (ipsecuser) authenticated.

177 02/07/2002 08:00:22.110 SEV=9 IKEDBG/0 RPT=95 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
constructing blank hash

178 02/07/2002 08:00:22.110 SEV=9 IKEDBG/0 RPT=96 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
constructing qm hash

179 02/07/2002 08:00:22.110 SEV=8 IKEDBG/0 RPT=97 172.18.124.241 
SENDING Message (msgid=4cc78f4e) with payloads : 
HDR + HASH (8) + ATTR (14) + NONE (0) ... total length : 60

181 02/07/2002 08:00:22.110 SEV=8 AUTHDBG/60 RPT=5 
AUTH_UnbindServer(9b1544c, 0, 0)

182 02/07/2002 08:00:22.110 SEV=9 AUTHDBG/70 RPT=5 
Auth Server 16b3fa0 has been unbound from ACB 9b1544c, sessions = 0

183 02/07/2002 08:00:22.110 SEV=8 AUTHDBG/10 RPT=3 
AUTH_Int_FreeAuthCB(9b1544c)

184 02/07/2002 08:00:22.110 SEV=7 AUTH/13 RPT=3 
Authentication session closed: handle = 137

185 02/07/2002 08:00:22.110 SEV=8 IKEDBG/0 RPT=98 172.18.124.241 
RECEIVED Message (msgid=4cc78f4e) with payloads : 
HDR + HASH (8) + ATTR (14) + NONE (0) ... total length : 56

187 02/07/2002 08:00:22.110 SEV=9 IKEDBG/1 RPT=13 
process_attr(): Enter!

188 02/07/2002 08:00:22.110 SEV=9 IKEDBG/1 RPT=14 
Processing cfg ACK attributes

189 02/07/2002 08:00:22.180 SEV=8 IKEDBG/0 RPT=99 172.18.124.241 
RECEIVED Message (msgid=38a7c320) with payloads : 
HDR + HASH (8) + ATTR (14) + NONE (0) ... total length : 154

191 02/07/2002 08:00:22.180 SEV=9 IKEDBG/1 RPT=15 
process_attr(): Enter!

192 02/07/2002 08:00:22.180 SEV=9 IKEDBG/1 RPT=16 
Processing cfg Request attributes

193 02/07/2002 08:00:22.180 SEV=9 IKEDBG/53 RPT=1 
MODE_CFG: Received request for IPV4 address!

194 02/07/2002 08:00:22.180 SEV=9 IKEDBG/53 RPT=2 
MODE_CFG: Received request for IPV4 net mask!

195 02/07/2002 08:00:22.180 SEV=9 IKEDBG/53 RPT=3 
MODE_CFG: Received request for DNS server address!

196 02/07/2002 08:00:22.180 SEV=9 IKEDBG/53 RPT=4 
MODE_CFG: Received request for WINS server address!

197 02/07/2002 08:00:22.180 SEV=6 IKE/130 RPT=1 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Received unsupported transaction mode attribute: 5

199 02/07/2002 08:00:22.180 SEV=9 IKEDBG/53 RPT=5 
MODE_CFG: Received request for Application Version!

200 02/07/2002 08:00:22.180 SEV=9 IKEDBG/53 RPT=6 
MODE_CFG: Received request for Banner!

201 02/07/2002 08:00:22.180 SEV=9 IKEDBG/53 RPT=7 
MODE_CFG: Received request for Save PW setting!

202 02/07/2002 08:00:22.180 SEV=9 IKEDBG/53 RPT=8 
MODE_CFG: Received request for Default Domain Name!

203 02/07/2002 08:00:22.180 SEV=9 IKEDBG/53 RPT=9 
MODE_CFG: Received request for Split Tunnel List!

204 02/07/2002 08:00:22.180 SEV=9 IKEDBG/53 RPT=10 
MODE_CFG: Received request for PFS setting!

205 02/07/2002 08:00:22.180 SEV=9 IKEDBG/53 RPT=11 
MODE_CFG: Received request for FWTYPE!

206 02/07/2002 08:00:22.180 SEV=9 IKEDBG/53 RPT=12 
MODE_CFG: Received request for UDP Port!

207 02/07/2002 08:00:22.180 SEV=9 IKEDBG/31 RPT=1 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Obtained IP addr (10.1.1.100) prior to initiating Mode Cfg (XAuth enabled)

209 02/07/2002 08:00:22.180 SEV=9 IKEDBG/0 RPT=100 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
constructing blank hash

210 02/07/2002 08:00:22.180 SEV=9 IKEDBG/0 RPT=101 172.18.124.241 
0000: 00010004 0A010164 F0010000 F0070000     .......d........
0010: 00070062 43697363 6F205379 7374656D     ...bCisco System
0020: 732C2049 6E632E2F 56504E20 33303030     s, Inc./VPN 3000
0030: 20436F6E 63656E74 7261746F 72205665      Concentrator Ve
0040: 7273696F 6E20332E 352E5265 6C206275     rsion 3.5.Rel bu
0050: 696C7420 62792076 6D757270 6879206F     ilt by vmurphy o

216 02/07/2002 08:00:22.180 SEV=9 IKEDBG/0 RPT=102 172.18.124.241 
0000: 6E204E6F 76203237 20323030 31203131     n Nov 27 2001 11
0010: 3A32323A 3331                           :22:31

218 02/07/2002 08:00:22.180 SEV=9 IKEDBG/0 RPT=103 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
constructing qm hash

219 02/07/2002 08:00:22.180 SEV=8 IKEDBG/0 RPT=104 172.18.124.241 
SENDING Message (msgid=38a7c320) with payloads : 
HDR + HASH (8) + ATTR (14) + NONE (0) ... total length : 174

221 02/07/2002 08:00:22.190 SEV=9 IKEDBG/21 RPT=1 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Delay Quick Mode processing, Cert/Trans Exch/RM DSID in progress

223 02/07/2002 08:00:22.190 SEV=4 AUTH/22 RPT=86 
User ipsecuser connected

224 02/07/2002 08:00:22.190 SEV=7 IKEDBG/22 RPT=1 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Resume Quick Mode processing, Cert/Trans Exch/RM DSID completed

226 02/07/2002 08:00:22.200 SEV=4 IKE/119 RPT=68 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
PHASE 1 COMPLETED

227 02/07/2002 08:00:22.200 SEV=6 IKE/121 RPT=1 172.18.124.241 
Keep-alive type for this connection: DPD

228 02/07/2002 08:00:22.200 SEV=7 IKEDBG/0 RPT=105 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Starting phase 1 rekey timer: 82080000 (ms)

229 02/07/2002 08:00:22.200 SEV=9 IKEDBG/0 RPT=106 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
sending notify message

230 02/07/2002 08:00:22.200 SEV=9 IKEDBG/0 RPT=107 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
constructing blank hash

231 02/07/2002 08:00:22.200 SEV=9 IKEDBG/0 RPT=108 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
constructing qm hash

232 02/07/2002 08:00:22.200 SEV=8 IKEDBG/0 RPT=109 172.18.124.241 
SENDING Message (msgid=be237358) with payloads : 
HDR + HASH (8) + NOTIFY (11) + NONE (0) ... total length : 88

234 02/07/2002 08:00:22.200 SEV=8 IKEDBG/0 RPT=110 172.18.124.241 
RECEIVED Message (msgid=472c326b) with payloads : 
HDR + HASH (8) + SA (1) + NONCE (10) + ID (5) + ID (5) + NONE (0) ... total leng
th : 792

237 02/07/2002 08:00:22.200 SEV=9 IKEDBG/0 RPT=111 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
processing hash

238 02/07/2002 08:00:22.200 SEV=9 IKEDBG/0 RPT=112 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
processing SA payload

239 02/07/2002 08:00:22.200 SEV=9 IKEDBG/1 RPT=17 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
processing nonce payload

240 02/07/2002 08:00:22.200 SEV=9 IKEDBG/1 RPT=18 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Processing ID

241 02/07/2002 08:00:22.200 SEV=5 IKE/25 RPT=62 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Received remote Proxy Host data in ID Payload:
Address 10.1.1.100, Protocol 0, Port 0

244 02/07/2002 08:00:22.200 SEV=9 IKEDBG/1 RPT=19 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Processing ID

245 02/07/2002 08:00:22.200 SEV=5 IKE/24 RPT=61 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Received local Proxy Host data in ID Payload:
Address 172.18.124.133, Protocol 0, Port 0

248 02/07/2002 08:00:22.200 SEV=8 IKEDBG/0 RPT=113 
QM IsRekeyed old sa not found by addr

249 02/07/2002 08:00:22.200 SEV=5 IKE/66 RPT=121 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
IKE Remote Peer configured for SA: ESP-3DES-MD5

251 02/07/2002 08:00:22.200 SEV=9 IKEDBG/0 RPT=114 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
processing IPSEC SA

252 02/07/2002 08:00:22.200 SEV=8 IKEDBG/0 RPT=115 
Proposal # 2, Transform # 1, Type ESP, Id Triple-DES
Parsing received transform:
  Phase 2 failure:
  Mismatched attr types for class HMAC Algorithm:
    Rcv'd: SHA
    Cfg'd: MD5

256 02/07/2002 08:00:22.200 SEV=7 IKEDBG/27 RPT=1 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
IPSec SA Proposal # 3, Transform # 1 acceptable

258 02/07/2002 08:00:22.200 SEV=7 IKEDBG/0 RPT=116 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
IKE: requesting SPI!

259 02/07/2002 08:00:22.200 SEV=9 IPSECDBG/6 RPT=1 
IPSEC key message parse - msgtype 6, len 200, vers 1, pid 00000000, seq 129, err
 0, type 2, mode 0, state 32, label 0, pad 0, spi 00000000, encrKeyLen 0, hashKe
yLen 0, ivlen 0, alg 0, hmacAlg 0, lifetype 0, lifetime1 708648, lifetime2 0, ds
Id 300

263 02/07/2002 08:00:22.200 SEV=9 IPSECDBG/1 RPT=1 
Processing KEY_GETSPI msg!

264 02/07/2002 08:00:22.200 SEV=7 IPSECDBG/13 RPT=1 
Reserved SPI 1037485220

265 02/07/2002 08:00:22.200 SEV=8 IKEDBG/6 RPT=1 
IKE got SPI from key engine: SPI = 0x3dd6c4a4

266 02/07/2002 08:00:22.200 SEV=9 IKEDBG/0 RPT=117 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
oakley constucting quick mode

267 02/07/2002 08:00:22.200 SEV=9 IKEDBG/0 RPT=118 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
constructing blank hash

268 02/07/2002 08:00:22.200 SEV=9 IKEDBG/0 RPT=119 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
constructing ISA_SA for ipsec

269 02/07/2002 08:00:22.200 SEV=5 IKE/75 RPT=121 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Overriding Initiator's IPSec rekeying duration from 2147483 to 28800 seconds

271 02/07/2002 08:00:22.200 SEV=9 IKEDBG/1 RPT=20 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
constructing ipsec nonce payload

272 02/07/2002 08:00:22.200 SEV=9 IKEDBG/1 RPT=21 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
constructing proxy ID

273 02/07/2002 08:00:22.200 SEV=7 IKEDBG/0 RPT=120 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Transmitting Proxy Id:
  Remote host: 10.1.1.100  Protocol 0  Port 0
  Local host:  172.18.124.133  Protocol 0  Port 0

277 02/07/2002 08:00:22.200 SEV=7 IKEDBG/0 RPT=121 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Sending RESPONDER LIFETIME notification to Initiator

279 02/07/2002 08:00:22.200 SEV=9 IKEDBG/0 RPT=122 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
constructing qm hash

280 02/07/2002 08:00:22.200 SEV=8 IKEDBG/0 RPT=123 172.18.124.241 
SENDING Message (msgid=472c326b) with payloads : 
HDR + HASH (8) + SA (1) + NONCE (10) + ID (5) + ID (5) + NOTIFY (11) + NONE (0) 
... total length : 172

283 02/07/2002 08:00:22.210 SEV=8 IKEDBG/0 RPT=124 172.18.124.241 
RECEIVED Message (msgid=64c59a32) with payloads : 
HDR + HASH (8) + SA (1) + NONCE (10) + ID (5) + ID (5) + NONE (0) ... total leng
th : 796

286 02/07/2002 08:00:22.210 SEV=9 IKEDBG/0 RPT=125 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
processing hash

287 02/07/2002 08:00:22.210 SEV=9 IKEDBG/0 RPT=126 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
processing SA payload

288 02/07/2002 08:00:22.210 SEV=9 IKEDBG/1 RPT=22 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
processing nonce payload

289 02/07/2002 08:00:22.210 SEV=9 IKEDBG/1 RPT=23 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Processing ID

290 02/07/2002 08:00:22.210 SEV=5 IKE/25 RPT=63 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Received remote Proxy Host data in ID Payload:
Address 10.1.1.100, Protocol 0, Port 0

293 02/07/2002 08:00:22.210 SEV=9 IKEDBG/1 RPT=24 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Processing ID

294 02/07/2002 08:00:22.210 SEV=5 IKE/34 RPT=61 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Received local IP Proxy Subnet data in ID Payload:
 Address 0.0.0.0, Mask 0.0.0.0, Protocol 0, Port 0

297 02/07/2002 08:00:22.210 SEV=8 IKEDBG/0 RPT=127 
QM IsRekeyed old sa not found by addr

298 02/07/2002 08:00:22.210 SEV=5 IKE/66 RPT=122 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
IKE Remote Peer configured for SA: ESP-3DES-MD5

300 02/07/2002 08:00:22.210 SEV=9 IKEDBG/0 RPT=128 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
processing IPSEC SA

301 02/07/2002 08:00:22.210 SEV=8 IKEDBG/0 RPT=129 
Proposal # 2, Transform # 1, Type ESP, Id Triple-DES
Parsing received transform:
  Phase 2 failure:
  Mismatched attr types for class HMAC Algorithm:
    Rcv'd: SHA
    Cfg'd: MD5

305 02/07/2002 08:00:22.210 SEV=7 IKEDBG/27 RPT=2 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
IPSec SA Proposal # 3, Transform # 1 acceptable

307 02/07/2002 08:00:22.210 SEV=7 IKEDBG/0 RPT=130 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
IKE: requesting SPI!

308 02/07/2002 08:00:22.210 SEV=9 IPSECDBG/6 RPT=2 
IPSEC key message parse - msgtype 6, len 200, vers 1, pid 00000000, seq 130, err
 0, type 2, mode 0, state 32, label 0, pad 0, spi 00000000, encrKeyLen 0, hashKe
yLen 0, ivlen 0, alg 0, hmacAlg 0, lifetype 0, lifetime1 708648, lifetime2 0, ds
Id 300

312 02/07/2002 08:00:22.210 SEV=9 IPSECDBG/1 RPT=2 
Processing KEY_GETSPI msg!

313 02/07/2002 08:00:22.210 SEV=7 IPSECDBG/13 RPT=2 
Reserved SPI 1517437317

314 02/07/2002 08:00:22.210 SEV=8 IKEDBG/6 RPT=2 
IKE got SPI from key engine: SPI = 0x5a724185

315 02/07/2002 08:00:22.210 SEV=9 IKEDBG/0 RPT=131 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
oakley constucting quick mode

316 02/07/2002 08:00:22.210 SEV=9 IKEDBG/0 RPT=132 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
constructing blank hash

317 02/07/2002 08:00:22.210 SEV=9 IKEDBG/0 RPT=133 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
constructing ISA_SA for ipsec

318 02/07/2002 08:00:22.210 SEV=5 IKE/75 RPT=122 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Overriding Initiator's IPSec rekeying duration from 2147483 to 28800 seconds

320 02/07/2002 08:00:22.210 SEV=9 IKEDBG/1 RPT=25 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
constructing ipsec nonce payload

321 02/07/2002 08:00:22.210 SEV=9 IKEDBG/1 RPT=26 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
constructing proxy ID

322 02/07/2002 08:00:22.210 SEV=7 IKEDBG/0 RPT=134 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Transmitting Proxy Id:
  Remote host: 10.1.1.100  Protocol 0  Port 0
  Local subnet:  0.0.0.0  mask 0.0.0.0 Protocol 0  Port 0

326 02/07/2002 08:00:22.210 SEV=7 IKEDBG/0 RPT=135 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Sending RESPONDER LIFETIME notification to Initiator

328 02/07/2002 08:00:22.210 SEV=9 IKEDBG/0 RPT=136 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
constructing qm hash

329 02/07/2002 08:00:22.220 SEV=8 IKEDBG/0 RPT=137 172.18.124.241 
SENDING Message (msgid=64c59a32) with payloads : 
HDR + HASH (8) + SA (1) + NONCE (10) + ID (5) + ID (5) + NOTIFY (11) + NONE (0) 
... total length : 176

332 02/07/2002 08:00:22.220 SEV=8 IKEDBG/0 RPT=138 172.18.124.241 
RECEIVED Message (msgid=472c326b) with payloads : 
HDR + HASH (8) + NONE (0) ... total length : 48

334 02/07/2002 08:00:22.220 SEV=9 IKEDBG/0 RPT=139 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
processing hash

335 02/07/2002 08:00:22.220 SEV=9 IKEDBG/0 RPT=140 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
loading all IPSEC SAs

336 02/07/2002 08:00:22.220 SEV=9 IKEDBG/1 RPT=27 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Generating Quick Mode Key!

337 02/07/2002 08:00:22.220 SEV=9 IKEDBG/1 RPT=28 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Generating Quick Mode Key!

338 02/07/2002 08:00:22.220 SEV=7 IKEDBG/0 RPT=141 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Loading host:
  Dst: 172.18.124.133
  Src: 10.1.1.100

340 02/07/2002 08:00:22.220 SEV=4 IKE/49 RPT=129 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Security negotiation complete for User (ipsecuser)
Responder, Inbound SPI = 0x3dd6c4a4, Outbound SPI = 0x8104887e

343 02/07/2002 08:00:22.220 SEV=9 IPSECDBG/6 RPT=3 
IPSEC key message parse - msgtype 1, len 624, vers 1, pid 00000000, seq 0, err 0
, type 2, mode 1, state 64, label 0, pad 0, spi 8104887e, encrKeyLen 24, hashKey
Len 16, ivlen 8, alg 2, hmacAlg 3, lifetype 0, lifetime1 708648, lifetime2 0, ds
Id 0

347 02/07/2002 08:00:22.220 SEV=9 IPSECDBG/1 RPT=3 
Processing KEY_ADD msg!

348 02/07/2002 08:00:22.220 SEV=9 IPSECDBG/1 RPT=4 
key_msghdr2secassoc(): Enter

349 02/07/2002 08:00:22.220 SEV=7 IPSECDBG/1 RPT=5 
No USER filter configured

350 02/07/2002 08:00:22.220 SEV=9 IPSECDBG/1 RPT=6 
KeyProcessAdd: Enter

351 02/07/2002 08:00:22.220 SEV=8 IPSECDBG/1 RPT=7 
KeyProcessAdd: Adding outbound SA

352 02/07/2002 08:00:22.220 SEV=8 IPSECDBG/1 RPT=8 
KeyProcessAdd: src 172.18.124.133 mask 0.0.0.0, dst 10.1.1.100 mask 0.0.0.0

353 02/07/2002 08:00:22.220 SEV=8 IPSECDBG/1 RPT=9 
KeyProcessAdd: FilterIpsecAddIkeSa success

354 02/07/2002 08:00:22.220 SEV=9 IPSECDBG/6 RPT=4 
IPSEC key message parse - msgtype 3, len 336, vers 1, pid 00000000, seq 0, err 0
, type 2, mode 1, state 32, label 0, pad 0, spi 3dd6c4a4, encrKeyLen 24, hashKey
Len 16, ivlen 8, alg 2, hmacAlg 3, lifetype 0, lifetime1 708648, lifetime2 0, ds
Id 0

358 02/07/2002 08:00:22.220 SEV=9 IPSECDBG/1 RPT=10 
Processing KEY_UPDATE msg!

359 02/07/2002 08:00:22.220 SEV=9 IPSECDBG/1 RPT=11 
Update inbound SA addresses

360 02/07/2002 08:00:22.220 SEV=9 IPSECDBG/1 RPT=12 
key_msghdr2secassoc(): Enter

361 02/07/2002 08:00:22.220 SEV=7 IPSECDBG/1 RPT=13 
No USER filter configured

362 02/07/2002 08:00:22.220 SEV=9 IPSECDBG/1 RPT=14 
KeyProcessUpdate: Enter

363 02/07/2002 08:00:22.220 SEV=8 IPSECDBG/1 RPT=15 
KeyProcessUpdate: success

364 02/07/2002 08:00:22.220 SEV=8 IKEDBG/7 RPT=1 
IKE got a KEY_ADD msg for SA: SPI = 0x8104887e

365 02/07/2002 08:00:22.220 SEV=8 IKEDBG/0 RPT=142 
pitcher: rcv KEY_UPDATE, spi 0x3dd6c4a4

366 02/07/2002 08:00:22.220 SEV=4 IKE/120 RPT=129 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
PHASE 2 COMPLETED (msgid=472c326b)

367 02/07/2002 08:00:22.280 SEV=8 IKEDBG/0 RPT=143 172.18.124.241 
RECEIVED Message (msgid=64c59a32) with payloads : 
HDR + HASH (8) + NONE (0) ... total length : 48

369 02/07/2002 08:00:22.280 SEV=9 IKEDBG/0 RPT=144 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
processing hash

370 02/07/2002 08:00:22.280 SEV=9 IKEDBG/0 RPT=145 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
loading all IPSEC SAs

371 02/07/2002 08:00:22.280 SEV=9 IKEDBG/1 RPT=29 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Generating Quick Mode Key!

372 02/07/2002 08:00:22.280 SEV=9 IKEDBG/1 RPT=30 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Generating Quick Mode Key!

373 02/07/2002 08:00:22.280 SEV=7 IKEDBG/0 RPT=146 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Loading subnet:
  Dst: 0.0.0.0  mask: 0.0.0.0
  Src: 10.1.1.100

375 02/07/2002 08:00:22.280 SEV=4 IKE/49 RPT=130 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
Security negotiation complete for User (ipsecuser)
Responder, Inbound SPI = 0x5a724185, Outbound SPI = 0x285e6ed0

378 02/07/2002 08:00:22.280 SEV=9 IPSECDBG/6 RPT=5 
IPSEC key message parse - msgtype 1, len 624, vers 1, pid 00000000, seq 0, err 0
, type 2, mode 1, state 64, label 0, pad 0, spi 285e6ed0, encrKeyLen 24, hashKey
Len 16, ivlen 8, alg 2, hmacAlg 3, lifetype 0, lifetime1 708648, lifetime2 0, ds
Id 0

382 02/07/2002 08:00:22.280 SEV=9 IPSECDBG/1 RPT=16 
Processing KEY_ADD msg!

383 02/07/2002 08:00:22.280 SEV=9 IPSECDBG/1 RPT=17 
key_msghdr2secassoc(): Enter

384 02/07/2002 08:00:22.280 SEV=7 IPSECDBG/1 RPT=18 
No USER filter configured

385 02/07/2002 08:00:22.280 SEV=9 IPSECDBG/1 RPT=19 
KeyProcessAdd: Enter

386 02/07/2002 08:00:22.280 SEV=8 IPSECDBG/1 RPT=20 
KeyProcessAdd: Adding outbound SA

387 02/07/2002 08:00:22.280 SEV=8 IPSECDBG/1 RPT=21 
KeyProcessAdd: src 0.0.0.0 mask 255.255.255.255, dst 10.1.1.100 mask 0.0.0.0

388 02/07/2002 08:00:22.280 SEV=8 IPSECDBG/1 RPT=22 
KeyProcessAdd: FilterIpsecAddIkeSa success

389 02/07/2002 08:00:22.280 SEV=9 IPSECDBG/6 RPT=6 
IPSEC key message parse - msgtype 3, len 336, vers 1, pid 00000000, seq 0, err 0
, type 2, mode 1, state 32, label 0, pad 0, spi 5a724185, encrKeyLen 24, hashKey
Len 16, ivlen 8, alg 2, hmacAlg 3, lifetype 0, lifetime1 708648, lifetime2 0, ds
Id 0

393 02/07/2002 08:00:22.280 SEV=9 IPSECDBG/1 RPT=23 
Processing KEY_UPDATE msg!

394 02/07/2002 08:00:22.280 SEV=9 IPSECDBG/1 RPT=24 
Update inbound SA addresses

395 02/07/2002 08:00:22.280 SEV=9 IPSECDBG/1 RPT=25 
key_msghdr2secassoc(): Enter

396 02/07/2002 08:00:22.280 SEV=7 IPSECDBG/1 RPT=26 
No USER filter configured

397 02/07/2002 08:00:22.280 SEV=9 IPSECDBG/1 RPT=27 
KeyProcessUpdate: Enter

398 02/07/2002 08:00:22.280 SEV=8 IPSECDBG/1 RPT=28 
KeyProcessUpdate: success

399 02/07/2002 08:00:22.280 SEV=8 IKEDBG/7 RPT=2 
IKE got a KEY_ADD msg for SA: SPI = 0x285e6ed0

400 02/07/2002 08:00:22.280 SEV=8 IKEDBG/0 RPT=147 
pitcher: rcv KEY_UPDATE, spi 0x5a724185

401 02/07/2002 08:00:22.280 SEV=4 IKE/120 RPT=130 172.18.124.241 
Group [ipsecgroup] User [ipsecuser]
PHASE 2 COMPLETED (msgid=64c59a32)

Informações Relacionadas

• Página de suporte do Cisco VPN 3000 Series Concentrator
• Página de suporte ao cliente do Cisco VPN 3000 Series
• Negociação IPsec/Protocolos IKE
• Suporte Técnico e Documentação - Cisco Systems