PIX para PIX 6.x: Exemplo de configuração de Easy VPN (NEM)
Contents
Introduction
Este documento fornece uma configuração de exemplo para IPsec entre o PIX Easy VPN Remote Hardware Client e o PIX Easy VPN Server. O recurso Easy VPN Remote para o PIX foi introduzido na versão 6.2 e também é chamado de cliente de hardware/cliente EzVPN. O Cisco Easy VPN Server é compatível com o software PIX versão 6.0 e posterior.
Consulte PIX/ASA 7.x Easy VPN com um ASA 5500 como o Exemplo de Configuração de Servidor e PIX 506E como o Cliente (NEM) para saber mais sobre o mesmo cenário em que o Security Appliance é executado com a versão de software 7.x.
Consulte PIX/ASA 7.x Easy VPN com um ASA 5500 como o Servidor e o Cisco 871 como o Exemplo de Configuração Remota de Easy VPN para obter mais informações sobre um cenário semelhante em que o Cisco 871 Router atua como o Easy VPN Remote.
Consulte VPN Hardware Client em um PIX 501/506 Series Security Appliance com VPN 3000 Concentrator Configuration Example para obter mais informações sobre um cenário semelhante em que o Cisco VPN 3000 Concentrator atua como o Easy VPN Server.
Consulte PIX 501/506 Easy VPN Remote para um IOS Router no Network Extension Mode com Extended Authentication Configuration Example para obter mais informações sobre um cenário semelhante em que o Cisco IOS® Router atua como o Easy VPN Server.
Prerequisites
Requirements
Certifique-se de atender a estes requisitos antes de tentar esta configuração:
-
Certifique-se de que o seu PIX Easy VPN Remote Hardware Client seja um PIX 501 ou PIX 506/506E que execute o software PIX versão 6.2 ou posterior.
-
Certifique-se de que o seu Easy VPN Server seja um PIX Firewall que execute o PIX Software versão 6.0 ou posterior.
Componentes Utilizados
As informações neste documento são baseadas nestas versões de software e hardware:
-
O PIX Easy VPN Remote Hardware Client é um PIX 501 que executa o PIX Software versão 6.3(1).
-
O Easy VPN Server é um PIX 515 que executa o software PIX versão 6.3(1).
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Conventions
Consulte as Convenções de Dicas Técnicas da Cisco para obter mais informações sobre convenções de documentos.
Configurar
Nesta seção, você encontrará informações para configurar os recursos descritos neste documento.
Nota: Use a Command Lookup Tool (somente clientes registrados) para obter mais informações sobre os comandos usados nesta seção.
Diagrama de Rede
Este documento utiliza a seguinte configuração de rede:
Configurações
Este documento utiliza as seguintes configurações:
| PIX Easy VPN Server |
|---|
pix515#write terminal Building configuration... : Saved : PIX Version 6.3(1) !--- Specify speed and duplex settings. interface ethernet0 auto interface ethernet1 auto interface ethernet2 auto shutdown interface ethernet3 auto shutdown interface ethernet4 auto shutdown interface ethernet5 auto shutdown nameif ethernet0 outside security0 nameif ethernet1 inside security100 nameif ethernet2 intf2 security4 nameif ethernet3 intf3 security6 nameif ethernet4 intf4 security8 nameif ethernet5 intf5 security10 enable password 8Ry2YjIyt7RRXU24 encrypted passwd 2KFQnbNIdI.2KYOU encrypted hostname pix515 fixup protocol ftp 21 fixup protocol h323 h225 1720 fixup protocol h323 ras 1718-1719 fixup protocol http 80 fixup protocol ils 389 fixup protocol rsh 514 fixup protocol rtsp 554 fixup protocol sip 5060 fixup protocol sip udp 5060 fixup protocol skinny 2000 fixup protocol smtp 25 fixup protocol sqlnet 1521 names !--- Specify split tunnelling access list and "nonat" access list. access-list 101 permit ip 10.2.2.0 255.255.255.0 10.1.1.0 255.255.255.0 pager lines 24 mtu outside 1500 mtu inside 1500 mtu intf2 1500 mtu intf3 1500 mtu intf4 1500 mtu intf5 1500 !--- Define IP address for the PIX's inside and outside interfaces. ip address outside 172.16.2.1 255.255.255.0 ip address inside 10.2.2.1 255.255.255.0 no ip address intf2 no ip address intf3 no ip address intf4 no ip address intf5 ip audit info action alarm ip audit attack action alarm ip local pool ippool 10.3.3.1-10.3.3.254 no failover failover timeout 0:00:00 failover poll 15 no failover ip address outside no failover ip address inside no failover ip address intf2 no failover ip address intf3 no failover ip address intf4 no failover ip address intf5 pdm history enable arp timeout 14400 !--- Configure Network Address Translation (NAT)/ !--- Port Address Translation (PAT) for regular traffic, !--- as well as NAT for IPsec traffic. global (outside) 1 interface nat (inside) 0 access-list 101 nat (inside) 1 0.0.0.0 0.0.0.0 0 0 !--- Define the outside router as the default gateway. !--- Typically this is the IP address of your !--- Internet service provider's (ISP) router. route outside 0.0.0.0 0.0.0.0 172.16.2.2 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00 timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00 timeout uauth 0:05:00 absolute aaa-server TACACS+ protocol tacacs+ aaa-server RADIUS protocol radius aaa-server LOCAL protocol local no snmp-server location no snmp-server contact snmp-server community public no snmp-server enable traps floodguard enable sysopt connection permit-ipsec !--- Configure IPsec transform set and dynamic crypto map. crypto ipsec transform-set myset esp-aes esp-md5-hmac crypto dynamic-map dynmap 10 set transform-set myset crypto map mymap 10 ipsec-isakmp dynamic dynmap !--- Apply crypto map to the outside interface. crypto map mymap interface outside !--- Configure Phase 1 Internet Security Association !-- and Key Management Protocol (ISAKMP) parameters. isakmp enable outside isakmp identity address isakmp policy 10 authentication pre-share isakmp policy 10 encryption aes isakmp policy 10 hash md5 isakmp policy 10 group 2 isakmp policy 10 lifetime 86400 !--- Configure VPNGroup parameters, to be sent down to the client. vpngroup mygroup address-pool ippool vpngroup mygroup dns-server 10.2.2.2 vpngroup mygroup wins-server 10.2.2.2 vpngroup mygroup default-domain cisco.com vpngroup mygroup split-tunnel 101 vpngroup mygroup idle-time 1800 vpngroup mygroup password ******** vpngroup idle-time idle-time 1800 telnet timeout 5 ssh timeout 5 console timeout 0 terminal width 80 Cryptochecksum:67106d7a5a3aa3da0caaeea93b9fc8d6 : end [OK] pix515# |
| PIX Easy VPN Remote Hardware Client |
|---|
pix501#write terminal Building configuration... : Saved : PIX Version 6.3(1) !--- Specify speed and duplex settings. interface ethernet0 auto interface ethernet1 100full nameif ethernet0 outside security0 nameif ethernet1 inside security100 enable password 8Ry2YjIyt7RRXU24 encrypted passwd 2KFQnbNIdI.2KYOU encrypted hostname pix501 fixup protocol ftp 21 fixup protocol h323 h225 1720 fixup protocol h323 ras 1718-1719 fixup protocol http 80 fixup protocol ils 389 fixup protocol rsh 514 fixup protocol rtsp 554 fixup protocol sip 5060 fixup protocol sip udp 5060 fixup protocol skinny 2000 fixup protocol smtp 25 fixup protocol sqlnet 1521 names pager lines 24 mtu outside 1500 mtu inside 1500 !--- Define IP address for the PIX's inside and outside interfaces. ip address outside 172.16.1.1 255.255.255.0 ip address inside 10.1.1.1 255.255.255.0 ip audit info action alarm ip audit attack action alarm pdm history enable arp timeout 14400 !--- Configure NAT for traffic that is not encrypted. global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 0 0 !--- Define the outside router as the default gateway. !--- Typically this is the IP address of your ISP's router. route outside 0.0.0.0 0.0.0.0 172.16.1.2 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00 timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00 timeout uauth 0:05:00 absolute aaa-server TACACS+ protocol tacacs+ aaa-server RADIUS protocol radius aaa-server LOCAL protocol local no snmp-server location no snmp-server contact snmp-server community public no snmp-server enable traps floodguard enable telnet timeout 5 ssh timeout 5 console timeout 0 !--- Define Easy VPN Remote parameters. vpnclient server 172.16.2.1 vpnclient mode network-extension-mode vpnclient vpngroup mygroup password ******** !--- Enable the VPN Client. !--- (This automatically initiates the IPSec tunnel to the server.) vpnclient enable terminal width 80 Cryptochecksum:b8242b410ad8e3b372018cd1cff77f91 : end [OK] |
Verificar
Use esta seção para confirmar se a sua configuração funciona corretamente.
A Output Interpreter Tool ( somente clientes registrados) (OIT) oferece suporte a determinados comandos show. Use a OIT para exibir uma análise da saída do comando show.
Comandos show e saída de exemplo do PIX Easy VPN Server
-
show crypto isakmp sa — Exibe todas as associações de segurança (SA) atuais do Internet Key Exchange (IKE) em um peer.
pix515#show crypto isakmp sa Total : 1 Embryonic : 0 dst src state pending created 172.16.2.1 172.16.1.1 QM_IDLE 0 2 pix515# -
show crypto ipsec sa — Exibe SAs IPsec criadas entre peers.
pix515#show crypto ipsec sa !--- This command was issued after a ping !--- was attempted from the PC behind the !--- Easy VPN Client to the PC !--- behind the server. interface: outside Crypto map tag: mymap, local addr. 172.16.2.1 local ident (addr/mask/prot/port): (10.2.2.0/255.255.255.0/0/0) remote ident (addr/mask/prot/port): (10.1.1.0/255.255.255.0/0/0) current_peer: 172.16.1.1:500 dynamic allocated peer ip: 0.0.0.0 PERMIT, flags={} #pkts encaps: 4, #pkts encrypt: 4, #pkts digest 4 #pkts decaps: 4, #pkts decrypt: 4, #pkts verify 4 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 0, #pkts compr. failed: 0, #pkts decompress failed: 0 #send errors 0, #recv errors 0 !--- Ping packets !--- were successfully exchanged between the !--- Easy VPN Remote Hardware Client !--- and the Easy VPN Server. local crypto endpt.: 172.16.2.1, remote crypto endpt.: 172.16.1.1 path mtu 1500, ipsec overhead 64, media mtu 1500 current outbound spi: 3a5a28e4 inbound esp sas: spi: 0x505c96c6(1348245190) transform: esp-aes esp-md5-hmac , in use settings ={Tunnel, } slot: 0, conn id: 2, crypto map: mymap sa timing: remaining key lifetime (k/sec): (4607999/28471) IV size: 16 bytes replay detection support: Y inbound ah sas: inbound pcp sas: outbound esp sas: spi: 0x3a5a28e4(978987236) transform: esp-aes esp-md5-hmac , in use settings ={Tunnel, } slot: 0, conn id: 1, crypto map: mymap sa timing: remaining key lifetime (k/sec): (4607999/28471) IV size: 16 bytes replay detection support: Y outbound ah sas: outbound pcp sas: local ident (addr/mask/prot/port): (10.2.2.0/255.255.255.0/0/0) remote ident (addr/mask/prot/port): (172.16.1.1/255.255.255.255/0/0) current_peer: 172.16.1.1:500 dynamic allocated peer ip: 0.0.0.0 PERMIT, flags={} #pkts encaps: 0, #pkts encrypt: 0, #pkts digest 0 #pkts decaps: 0, #pkts decrypt: 0, #pkts verify 0 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 0, #pkts compr. failed: 0, #pkts decompress failed: 0 #send errors 0, #recv errors 0 local crypto endpt.: 172.16.2.1, remote crypto endpt.: 172.16.1.1 path mtu 1500, ipsec overhead 64, media mtu 1500 current outbound spi: 27f378f9 inbound esp sas: spi: 0xf2bb4f00(4072361728) transform: esp-aes esp-md5-hmac , in use settings ={Tunnel, } slot: 0, conn id: 3, crypto map: mymap sa timing: remaining key lifetime (k/sec): (4608000/27796) IV size: 16 bytes replay detection support: Y inbound ah sas: inbound pcp sas: outbound esp sas: spi: 0x27f378f9(670267641) transform: esp-aes esp-md5-hmac , in use settings ={Tunnel, } slot: 0, conn id: 4, crypto map: mymap sa timing: remaining key lifetime (k/sec): (4608000/27787) IV size: 16 bytes replay detection support: Y outbound ah sas: outbound pcp sas: pix515#
Comandos show e exemplo de saída do cliente de hardware remoto PIX Easy VPN
-
vpnclient enable —Habilita uma conexão Easy VPN Remote. (No Network Extension Mode (NEM), o túnel está ativo mesmo quando não há tráfego interessante para ser trocado com o headend Easy VPN Server.)
pix501(config)#vpnclient enable
-
show crypto isakmp policy — Exibe os parâmetros para cada política IKE.
pix501#show crypto isakmp policy Default protection suite encryption algorithm: DES - Data Encryption Standard (56 bit keys). hash algorithm: Secure Hash Standard authentication method: Rivest-Shamir-Adleman Signature Diffie-Hellman group: #1 (768 bit) lifetime: 86400 seconds, no volume limitA saída do comando show crypto isakmp policy depois que o cliente de hardware está ativado é mostrada aqui.
pix501(config)#show crypto isakmp policy Protection suite of priority 65001 encryption algorithm: AES - Advanced Encryption Standard (256 bit keys). hash algorithm: Secure Hash Standard authentication method: Pre-Shared Key with XAUTH Diffie-Hellman group: #2 (1024 bit) lifetime: 86400 seconds, no volume limit Protection suite of priority 65002 encryption algorithm: AES - Advanced Encryption Standard (256 bit keys). hash algorithm: Message Digest 5 authentication method: Pre-Shared Key with XAUTH Diffie-Hellman group: #2 (1024 bit) lifetime: 86400 seconds, no volume limit Protection suite of priority 65003 encryption algorithm: AES - Advanced Encryption Standard (192 bit keys). hash algorithm: Secure Hash Standard authentication method: Pre-Shared Key with XAUTH Diffie-Hellman group: #2 (1024 bit) lifetime: 86400 seconds, no volume limit Protection suite of priority 65004 encryption algorithm: AES - Advanced Encryption Standard (192 bit keys). hash algorithm: Message Digest 5 authentication method: Pre-Shared Key with XAUTH Diffie-Hellman group: #2 (1024 bit) lifetime: 86400 seconds, no volume limit Protection suite of priority 65005 encryption algorithm: AES - Advanced Encryption Standard (128 bit keys). hash algorithm: Secure Hash Standard authentication method: Pre-Shared Key with XAUTH Diffie-Hellman group: #2 (1024 bit) lifetime: 86400 seconds, no volume limit Protection suite of priority 65006 encryption algorithm: AES - Advanced Encryption Standard (128 bit keys). hash algorithm: Message Digest 5 authentication method: Pre-Shared Key with XAUTH Diffie-Hellman group: #2 (1024 bit) lifetime: 86400 seconds, no volume limit Protection suite of priority 65007 encryption algorithm: Three key triple DES hash algorithm: Secure Hash Standard authentication method: Pre-Shared Key with XAUTH Diffie-Hellman group: #2 (1024 bit) lifetime: 86400 seconds, no volume limit Protection suite of priority 65008 encryption algorithm: Three key triple DES hash algorithm: Message Digest 5 authentication method: Pre-Shared Key with XAUTH Diffie-Hellman group: #2 (1024 bit) lifetime: 86400 seconds, no volume limit Protection suite of priority 65009 encryption algorithm: DES - Data Encryption Standard (56 bit keys). hash algorithm: Message Digest 5 authentication method: Pre-Shared Key with XAUTH Diffie-Hellman group: #2 (1024 bit) lifetime: 86400 seconds, no volume limit Protection suite of priority 65010 encryption algorithm: AES - Advanced Encryption Standard (256 bit keys). hash algorithm: Secure Hash Standard authentication method: Pre-Shared Key Diffie-Hellman group: #2 (1024 bit) lifetime: 86400 seconds, no volume limit Protection suite of priority 65011 encryption algorithm: AES - Advanced Encryption Standard (256 bit keys). hash algorithm: Message Digest 5 authentication method: Pre-Shared Key Diffie-Hellman group: #2 (1024 bit) lifetime: 86400 seconds, no volume limit Protection suite of priority 65012 encryption algorithm: AES - Advanced Encryption Standard (192 bit keys). hash algorithm: Secure Hash Standard authentication method: Pre-Shared Key Diffie-Hellman group: #2 (1024 bit) lifetime: 86400 seconds, no volume limit Protection suite of priority 65013 encryption algorithm: AES - Advanced Encryption Standard (192 bit keys). hash algorithm: Message Digest 5 authentication method: Pre-Shared Key Diffie-Hellman group: #2 (1024 bit) lifetime: 86400 seconds, no volume limit Protection suite of priority 65014 encryption algorithm: AES - Advanced Encryption Standard (128 bit keys). hash algorithm: Secure Hash Standard authentication method: Pre-Shared Key Diffie-Hellman group: #2 (1024 bit) lifetime: 86400 seconds, no volume limit Protection suite of priority 65015 encryption algorithm: AES - Advanced Encryption Standard (128 bit keys). hash algorithm: Message Digest 5 authentication method: Pre-Shared Key Diffie-Hellman group: #2 (1024 bit) lifetime: 86400 seconds, no volume limit Protection suite of priority 65016 encryption algorithm: Three key triple DES hash algorithm: Secure Hash Standard authentication method: Pre-Shared Key Diffie-Hellman group: #2 (1024 bit) lifetime: 86400 seconds, no volume limit Protection suite of priority 65017 encryption algorithm: Three key triple DES hash algorithm: Message Digest 5 authentication method: Pre-Shared Key Diffie-Hellman group: #2 (1024 bit) lifetime: 86400 seconds, no volume limit Protection suite of priority 65018 encryption algorithm: DES - Data Encryption Standard (56 bit keys). hash algorithm: Message Digest 5 authentication method: Pre-Shared Key Diffie-Hellman group: #2 (1024 bit) lifetime: 86400 seconds, no volume limit -
show crypto isakmp sa — Exibe todas as SAs IKE atuais em um peer.
pix501(config)#show crypto isakmp sa Total : 1 Embryonic : 0 dst src state pending created 172.16.2.1 172.16.1.1 QM_IDLE 0 1 -
show crypto ipsec sa — Exibe SAs IPsec criadas entre peers.
pix501(config)#show crypto ipsec sa !--- This command was issued after a ping !--- was attempted from the PC behind the !--- Easy VPN client to the PC !--- behind the server. interface: outside Crypto map tag: _vpnc_cm, local addr. 172.16.1.1 local ident (addr/mask/prot/port): (10.1.1.0/255.255.255.0/0/0) remote ident (addr/mask/prot/port): (10.2.2.0/255.255.255.0/0/0) current_peer: 172.16.2.1:500 PERMIT, flags={origin_is_acl,} #pkts encaps: 4, #pkts encrypt: 4, #pkts digest 4 #pkts decaps: 4, #pkts decrypt: 4, #pkts verify 4 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 0, #pkts compr. failed: 0, #pkts decompress failed: 0 #send errors 1, #recv errors 0 !--- Ping packets !--- were successfully exchanged between !--- the Easy VPN Remote Hardware Client !--- and the Easy VPN Server. local crypto endpt.: 172.16.1.1, remote crypto endpt.: 172.16.2.1 path mtu 1500, ipsec overhead 64, media mtu 1500 current outbound spi: 505c96c6 inbound esp sas: spi: 0x3a5a28e4(978987236) transform: esp-aes esp-md5-hmac , in use settings ={Tunnel, } slot: 0, conn id: 4, crypto map: _vpnc_cm sa timing: remaining key lifetime (k/sec): (4607999/28745) IV size: 16 bytes replay detection support: Y inbound ah sas: inbound pcp sas: outbound esp sas: spi: 0x505c96c6(1348245190) transform: esp-aes esp-md5-hmac , in use settings ={Tunnel, } slot: 0, conn id: 3, crypto map: _vpnc_cm sa timing: remaining key lifetime (k/sec): (4607999/28745) IV size: 16 bytes replay detection support: Y outbound ah sas: outbound pcp sas: local ident (addr/mask/prot/port): (172.16.1.1/255.255.255.255/0/0) remote ident (addr/mask/prot/port): (10.2.2.0/255.255.255.0/0/0) current_peer: 172.16.2.1:500 PERMIT, flags={origin_is_acl,} #pkts encaps: 0, #pkts encrypt: 0, #pkts digest 0 #pkts decaps: 0, #pkts decrypt: 0, #pkts verify 0 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 0, #pkts compr. failed: 0, #pkts decompress failed: 0 #send errors 0, #recv errors 0 local crypto endpt.: 172.16.1.1, remote crypto endpt.: 172.16.2.1 path mtu 1500, ipsec overhead 64, media mtu 1500 current outbound spi: f2bb4f00 inbound esp sas: spi: 0x27f378f9(670267641) transform: esp-aes esp-md5-hmac , in use settings ={Tunnel, } slot: 0, conn id: 1, crypto map: _vpnc_cm sa timing: remaining key lifetime (k/sec): (4608000/28125) IV size: 16 bytes replay detection support: Y inbound ah sas: inbound pcp sas: outbound esp sas: spi: 0xf2bb4f00(4072361728) transform: esp-aes esp-md5-hmac , in use settings ={Tunnel, } slot: 0, conn id: 2, crypto map: _vpnc_cm sa timing: remaining key lifetime (k/sec): (4608000/28125) IV size: 16 bytes replay detection support: Y outbound ah sas: outbound pcp sas: pix501(config)# -
show vpnclient — Exibe informações de configuração de dispositivo VPN Client ou Easy VPN Remote.
pix501(config)#show vpnclient LOCAL CONFIGURATION vpnclient server 172.16.2.1 vpnclient mode network-extension-mode vpnclient vpngroup mygroup password ******** vpnclient enable DOWNLOADED DYNAMIC POLICY Current Server : 172.16.2.1 Primary DNS : 10.2.2.2 Primary WINS : 10.2.2.2 Default Domain : cisco.com PFS Enabled : No Secure Unit Authentication Enabled : No User Authentication Enabled : No Split Networks : 10.2.2.0/255.255.255.0 Backup Servers : None pix501(config)#
Troubleshoot
Esta seção fornece informações que podem ser usadas para o troubleshooting da sua configuração.
Se você configurou o Easy VPN Remote Hardware Client e o Easy VPN Server conforme descrito neste documento e ainda tiver problemas, reúna a saída de depuração de cada PIX e a saída dos comandos show para análise pelo Cisco Technical Assistance Center (TAC). Consulte também Troubleshooting do PIX para Passar o Tráfego de Dados em um Túnel IPsec Estabelecido ou Troubleshooting de Segurança IP - Entendendo e Usando Comandos de Depuração. Habilitar a depuração de IPSec no PIX.
Os comandos PIX debug e a saída de exemplo são mostrados aqui.
Nota:Consulte Informações Importantes sobre Comandos de Depuração antes de usar comandos debug.
Comandos do Easy VPN Server
-
debug crypto ipsec — Exibe as negociações de IPSec de fase 2
-
debug crypto isakmp — Exibe as negociações ISAKMP da Fase 1.
Esse é o exemplo de saída.
pix515(config)#
!--- As soon as the vpnclient enable command !--- is issued on the remote client PIX, !--- the server receives an IKE negotiation request.
crypto_isakmp_process_block:src:172.16.1.1,
dest:172.16.2.1 spt:500 dpt:500
OAK_AG exchange
ISAKMP (0): processing SA payload. message ID = 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 10 policy
ISAKMP: encryption AES-CBC
ISAKMP: keylength of 256
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: extended auth pre-share (init)
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): Checking ISAKMP transform 2 against priority 10 policy
ISAKMP: encryption AES-CBC
ISAKMP: keylength of 256
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: extended auth pre-share (init)
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): Checking ISAKMP transform 3 against priority 10 policy
ISAKMP: encryption AES-CBC
ISAKMP: keylength of 192
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: extended auth pre-share (init)
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): Checking ISAKMP transform 4 against priority 10 policy
ISAKMP: encryption AES-CBC
ISAKMP: keylength of 192
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: extended auth pre-share (init)
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): Checking ISAKMP transform 5 against priority 10 policy
ISAKMP: encryption AES-CBC
ISAKMP: keylength of 128
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: extended auth pre-share (init)
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): Checking ISAKMP transform 6 against priority 10 policy
ISAKMP: encryption AES-CBC
ISAKMP: keylength of 128
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: extended auth pre-share (init)
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): Checking ISAKMP transform 7 against priority 10 policy
ISAKMP: encryption 3DES-CBC
ISAKMP: hash SHA
ISAKMP: default group 2
ISAKMP: extended auth pre-share (init)
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): Checking ISAKMP transform 8 against priority 10 policy
ISAKMP: encryption 3DES-CBC
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: extended auth pre-share (init)
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): Checking ISAKMP transform 9 against priority 10 policy
ISAKMP: encryption DES-CBC
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: extended auth pre-share (init)
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 3
ISAKMP (0): Checking ISAKMP transform 10 against priority 10 policy
crypto_isakmp_process_block:src:172.16.1.1,
dest:172.16.2.1 spt:500 dpt:500
OAK_AG exchange
ISAKMP (0): processing HASH payload. message ID = 0
ISAKMP (0): processing NOTIFY payload 24578 protocol 1
spi 0, message ID = 0
ISAKMP (0): processing notify INITIAL_CONTACTIPSEC(key_engine):
got a queue event...
IPSEC(key_engine_delete_sas): rec'd delete notify from ISAKMP
IPSEC(key_engine_delete_sas): delete all SAs shared with 172.16.1.1
ISAKMP (0): processing vendor id payload
ISAKMP (0): received xauth v6 vendor id
ISAKMP (0): processing vendor id payload
ISAKMP (0): remote peer supports dead peer detection
ISAKMP (0): processing vendor id payload
ISAKMP (0): speaking to another IOS box!
ISAKMP (0): processing vendor id payload
crypto_isakmp_process_block:src:172.16.1.1,
dest:172.16.2.1 spt:500 dpt:500
ISAKMP_TRANSACTION exchange
crypto_isakmp_process_block:src:172.16.1.1,
dest:172.16.2.1 spt:500 dpt:500
OAK_QM exchange
oakley_process_quick_mode:
OAK_QM_IDLE
ISAKMP (0): processing SA payload. message ID = 4788683
ISAKMP : Checking IPSec proposal 1
ISAKMP: transform 1, ESP_AES
ISAKMP: attributes in transform:
ISAKMP: encaps is 1
ISAKMP: SA life type in seconds
ISAKMP: SA life duration (basic) of 28800
ISAKMP: SA life type in kilobytes
ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
ISAKMP: authenticator is HMAC-SHA
ISAKMP: key length is 256IPSEC(validate_proposal):
transform proposal (prot 3, trans 12, hmac_alg 2) not supported
ISAKMP (0): atts not acceptable. Next payload is 0
ISAKMP : Checking IPSec proposal 2
ISAKMP: transform 1, ESP_AES
ISAKMP: attributes in transform:
ISAKMP: encaps is 1
ISAKMP: SA life type in seconds
ISAKMP: SA life duration (basic) of 28800
ISAKMP: SA life type in kilobytes
ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
ISAKMP: authenticator is HMAC-MD5
ISAKMP: key length is 256IPSEC(validate_proposal):
transform proposal (prot 3, trans 12, hmac_alg 1) not supported
ISAKMP (0): atts not acceptable. Next payload is 0
ISAKMP : Checking IPSec proposal 3
ISAKMP: transform 1, ESP_AES
ISAKMP: attributes in transform:
ISAKMP: encaps is 1
ISAKMP: SA life type in seconds
ISAKMP: SA life duration (basic) of 28800
ISAKMP: SA life type in kilobytes
ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
ISAKMP: authenticator is HMAC-SHA
ISAKMP: key length is 192IPSEC(validate_proposal):
transform proposal (prot 3, trans 12, hmac_alg 2) not supported
ISAKMP (0): atts not acceptable. Next payload is 0
ISAKMP : Checking IPSec proposal 4
ISAKMP: transform 1, ESP_AES
ISAKMP: attributes in transform:
ISAKMP: encaps is 1
ISAKMP: SA life type in seconds
ISAKMP: SA life duration (basic) of 28800
ISAKMP: SA life type in kilobytes
ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
ISAKMP: authenticator is HMAC-MD5
ISAKMP: key length is 192IPSEC(validate_proposal):
transform proposal (prot 3, trans 12, hmac_alg 1) not supported
ISAKMP (0): atts not acceptable. Next payload is 0
ISAKMP : Checking IPSec proposal 5
ISAKMP: transform 1, ESP_AES
ISAKMP: attributes in transform:
ISAKMP: encaps is 1
ISAKMP: SA life type in seconds
ISAKMP: SA life duration (basic) of 28800
ISAKMP: SA life type in kilobytes
ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
ISAKMP: authenticator is HMAC-SHA
ISAKMP: key length is 128IPSEC(validate_proposal):
transform proposal (prot 3, trans 12, hmac_alg 2) not supported
ISAKMP (0): atts not acceptable. Next payload is 0
ISAKMP : Checking IPSec proposal 6
ISAKMP: transform 1, ESP_AES
ISAKMP: attributes in transform:
ISAKMP: encaps is 1
ISAKMP: SA life type in seconds
ISAKMP: SA life duration (basic) of 28800
ISAKMP: SA life type in kilobytes
ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
ISAKMP: authenticator is HMAC-MD5
ISAKMP: key length is 128
ISAKMP (0): atts are acceptable.IPSEC(validate_proposal_request):
proposal part #1,
(key eng. msg.) dest= 172.16.2.1, src= 172.16.1.1,
dest_proxy= 10.2.2.0/255.255.255.0/0/0 (type=4),
src_proxy= 172.16.1.1/255.255.255.255/0/0 (type=1),
protocol= ESP, transform= esp-aes esp-md5-hmac ,
lifedur= 0s and 0kb,
spi= 0x0(0), conn_id= 0, keysize= 128, flags= 0x4
!--- Both PIXes accept the policy for IPsec.
ISAKMP (0): processing NONCE payload. message ID = 4788683
ISAKMP (0): processing ID payload. message ID = 4788683
ISAKMP (0): ID_IPV4_ADDR src 172.16.1.1 prot 0 port 0
ISAKMP (0): processing ID payload. message ID = 4788683
ISAKMP (0): ID_IPV4_ADDR_SUBNET dst 10.2.2.0/255.255.255.0 prot 0
port 0IPSEC(key_engine): got a queue event...
IPSEC(spi_response): getting spi 0xf5720496(4117890198) for SA
from 172.16.1.1 to 172.16.2.1 for prot 3
return status is IKMP_NO_ERROR
crypto_isakmp_process_block:src:172.16.1.1,
dest:172.16.2.1 spt:500 dpt:500
OAK_QM exchange
oakley_process_quick_mode:
OAK_QM_AUTH_AWAIT
ISAKMP (0): Creating IPSec SAs
inbound SA from 172.16.1.1 to 172.16.2.1
(proxy 172.16.1.1 to 10.2.2.0)
has spi 4117890198 and conn_id 3 and flags 4
lifetime of 28800 seconds
crypto_isakmp_process_block:src:172.16.1.1,
dest:172.16.2.1 spt:500 dpt:500
ISAKMP (0): processing NOTIFY payload 36136 protocol 1
spi 0, message ID = 843197376
ISAMKP (0): received DPD_R_U_THERE from peer 172.16.1.1
ISAKMP (0): sending NOTIFY message 36137 protocol 1
return status is IKMP_NO_ERR_NO_TRANS
crypto_isakmp_process_block:src:172.16.1.1,
dest:172.16.2.1 spt:500 dpt:500
ISAKMP (0): processing NOTIFY payload 36136 protocol 1
spi 0, message ID = 1985282089
ISAMKP (0): received DPD_R_U_THERE from peer 172.16.1.1
ISAKMP (0): sending NOTIFY message 36137 protocol 1
return status is IKMP_NO_ERR_NO_TRANS
crypto_isakmp_process_block:src:172.16.1.1,
dest:172.16.2.1 spt:500 dpt:500
ISAKMP (0): processing NOTIFY payload 36136 protocol 1
spi 0, message ID = 1510977390
ISAMKP (0): received DPD_R_U_THERE from peer 172.16.1.1
ISAKMP (0): sending NOTIFY message 36137 protocol 1
return status is IKMP_NO_ERR_NO_TRANS
Comandos do Easy VPN Remote Hardware Client
-
debug crypto ipsec — Exibe as negociações de IPSec de fase 2
-
debug crypto isakmp — Exibe as negociações ISAKMP da Fase 1.
pix501(config)#vpnclient enable
(cIoSnAfKigM)P# (0): ID payload
next-payload : 13
type : 11
protocol : 17
port : 0
length : 11
ISAKMP (0): Total payload length: 15
ISAKMP (0:0): sending NAT-T vendor ID - rev 2 & 3
ISAKMP (0): beginning Aggressive Mode exchange
crypto_isakmp_process_block:src:172.16.2.1,
dest:172.16.1.1 spt:500 dpt:500
OAK_AG exchange
ISAKMP (0): processing SA payload. message ID = 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 65001 policy
ISAKMP: encryption AES-CBC
ISAKMP: keylength of 128
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: auth pre-share
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 65002 policy
ISAKMP: encryption AES-CBC
ISAKMP: keylength of 128
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: auth pre-share
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 65003 policy
ISAKMP: encryption AES-CBC
ISAKMP: keylength of 128
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: auth pre-share
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 65004 policy
ISAKMP: encryption AES-CBC
ISAKMP: keylength of 128
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: auth pre-share
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 65005 policy
ISAKMP: encryption AES-CBC
ISAKMP: keylength of 128
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: auth pre-share
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 65006 policy
ISAKMP: encryption AES-CBC
ISAKMP: keylength of 128
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: auth pre-share
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 65007 policy
ISAKMP: encryption AES-CBC
ISAKMP: keylength of 128
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: auth pre-share
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 65008 policy
ISAKMP: encryption AES-CBC
ISAKMP: keylength of 128
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: auth pre-share
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP (0): atts are not acceptable. Next payload is 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 65009 policy
ISAKMP: encryption AES-CBC
ISAKMP: keylength of 128
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP: auth pre-share
ISAKMP: life type in seconds
ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
ISAKMP : attributes being requested
crypto_isakmp_process_block:src:172.16.2.1,
dest:172.16.1.1 spt:500 dpt:500
ISAKMP (0): beginning Quick Mode exchange,
M-ID of 1112046058:424879eaIPSEC(key_engine): got a queue event...
IPSEC(spi_response): getting spi 0x274d3063(659370083) for SA
from 172.16.2.1 to 172.16.1.1 for prot 3
crypto_isakmp_process_block:src:172.16.2.1,
dest:172.16.1.1 spt:500 dpt:500
OAK_QM exchange
oakley_process_quick_mode:
OAK_QM_IDLE
ISAKMP (0): processing SA payload. message ID = 1112046058
ISAKMP : Checking IPSec proposal 1
ISAKMP: transform 1, ESP_AES
ISAKMP: attributes in transform:
ISAKMP: encaps is 1
ISAKMP: SA life type in seconds
ISAKMP: SA life duration (basic) of 28800
ISAKMP: SA life type in kilobytes
ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
ISAKMP: authenticator is HMAC-MD5
ISAKMP: key length is 128
ISAKMP (0): atts are acceptable.IPSEC(validate_proposal_request):
proposal part #1,
(key eng. msg.) dest= 172.16.2.1, src= 172.16.1.1,
dest_proxy= 10.2.2.0/255.255.255.0/0/0 (type=4),
src_proxy= 172.16.1.1/255.255.255.255/0/0 (type=1),
protocol= ESP, transform= esp-aes esp-md5-hmac ,
lifedur= 0s and 0kb,
spi= 0x0(0), conn_id= 0, keysize= 128, flags= 0x4
ISAKMP (0): processing NONCE payload. message ID = 1112046058
ISAKMP (0): processing ID payload. message ID = 1112046058
ISAKMP (0): processing ID payload. message ID = 1112046058
ISAKMP (0): Creating IPSec SAs
inbound SA from 172.16.2.1 to 172.16.1.1
(proxy 10.2.2.0 to 172.16.1.1)
has spi 659370083 and conn_id 2 and flags 4
lifetime of 28800 seconds
lifetime of 4608000 kilobytes
outbound SA from 172.16.1.1 to 172.16.2.1
(proxy 172.16.1.1 to 10.2.2.0)
has spi 264316759 and conn_id 1 and flags 4
lifetime of 28800 seconds
lifetime of 4608000 kilobytesIPSEC(key_engine):
got a queue event...
IPSEC(initialize_sas): ,
(key eng. msg.) dest= 172.16.1.1, src= 172.16.2.1,
dest_proxy= 172.16.1.1/255.255.255.255/0/0 (type=1),
src_proxy= 10.2.2.0/255.255.255.0/0/0 (type=4),
protocol= ESP, transform= esp-aes esp-md5-hmac ,
lifedur= 28800s and 4608000kb,
spi= 0x274d3063(659370083), conn_id= 2, keysize= 128, flags= 0x4
IPSEC(initialize_sas): ,
(key eng. msg.) src= 172.16.1.1, dest= 172.16.2.1,
src_proxy= 172.16.1.1/255.255.255.255/0/0 (type=1),
dest_proxy= 10.2.2.0/255.255.255.0/0/0 (type=4),
protocol= ESP, transform= esp-aes esp-md5-hmac ,
lifedur= 28800s and 4608000kb,
spi= 0xfc12757(264316759), conn_id= 1, keysize= 128, flags= 0x4
VPN Peer: IPSEC: Peer ip:172.16.2.1/500 Ref cnt incremented to:2
Total VPN Peers:1
VPN Peer: IPSEC: Peer ip:172.16.2.1/500 Ref cnt incremented to:3
Total VPN Peers:1
return status is IKMP_NO_ERROR
pix501(config)#
pix501(config)#
ISAKMP (0): sending NOTIFY message 36136 protocol 1
crypto_isakmp_process_block:src:172.16.2.1,
dest:172.16.1.1 spt:500 dpt:500
ISAKMP (0): processing NOTIFY payload 36137 protocol 1
spi 0, message ID = 136860646n
ISAMKP (0): received DPD_R_U_THERE_ACK from peer 172.16.2.1
-
debug vpncient — Exibe as negociações específicas do VPN Client.
pix501(config)#vpnclient enable pix501(config)# 505: VPNC CFG: transform set unconfig attempt done 506: VPNC CLI: no isakmp keepalive 10 507: VPNC CLI: no isakmp nat-traversal 20 508: VPNC CFG: IKE unconfig successful 509: VPNC CLI: no crypto map _vpnc_cm 510: VPNC CFG: crypto map deletion attempt done 511: VPNC CFG: crypto unconfig successful 512: VPNC CLI: no global (outside) 65001 513: VPNC CLI: no nat (inside) 0 access-list _vpnc_acl 514: VPNC CFG: nat unconfig attempt failed 515: VPNC CLI: no http 10.1.1.1 255.255.255.0 inside 516: VPNC CLI: no http server enable 517: VPNC CLI: no access-list _vpnc_acl 518: VPNC CFG: ACL deletion attempt failed 519: VPNC CLI: no crypto map _vpnc_cm interface outside 520: VPNC CFG: crypto map de/attach failed 521: VPNC CLI: no sysopt connection permit-ipsec 522: VPNC CLI: sysopt connection permit-ipsec 523: VPNC CFG: transform sets configured 524: VPNC CFG: crypto config successful 525: VPNC CLI: isakmp keepalive 10 526: VPNC CLI: isakmp nat-traversal 20 527: VPNC CFG: IKE config successful 528: VPNC CLI: http 10.1.1.1 255.255.255.0 inside 529: VPNC CLI: http server enable 530: VPNC CLI: no access-list _vpnc_acl 531: VPNC CFG: ACL deletion attempt failed 532: VPNC CLI: access-list _vpnc_acl permit ip host 172.16.1.1 host 172.16.2.1 533: VPNC CLI: crypto map _vpnc_cm 10 match address _vpnc_acl 534: VPNC CFG: crypto map acl update successful 535: VPNC CLI: no crypto map _vpnc_cm interface outside 536: VPNC CLI: crypto map _vpnc_cm interface outside 537: VPNC INF: IKE trigger request done 538: VPNC INF: Constructing policy download req 539: VPNC INF: Packing attributes for policy request 540: VPNC INF: Attributes being requested 541: VPNC ATT: ALT_DEF_DOMAIN: cisco.com 542: VPNC ATT: INTERNAL_IP4_NBNS: 10.2.2.2 543: VPNC ATT: INTERNAL_IP4_DNS: 10.2.2.2 544: VPNC ATT: ALT_SPLIT_INCLUDE 545: VPNC INF: 10.2.2.0/255.255.255.0 546: VPNC ATT: ALT_PFS: 0 547: VPNC ATT: ALT_CFG_SEC_UNIT: 0 548: VPNC ATT: ALT_CFG_USER_AUTH: 0 549: VPNC CLI: no access-list _vpnc_acl 550: VPNC CLI: access-list _vpnc_acl permit ip 10.1.1.0 255.255.255.0 10.2.2.0 255.255.255.0 551: VPNC CLI: access-list _vpnc_acl permit ip host 172.16.1.1 10.2.2.0 255.255.255.0 552: VPNC CFG: _vpnc_acl ST define done 553: VPNC CFG: Split DNS config attempt done 554: VPNC CLI: crypto map _vpnc_cm 10 match address _vpnc_acl 555: VPNC CFG: crypto map acl update successful 556: VPNC CLI: no crypto map _vpnc_cm interface outside 557: VPNC CLI: crypto map _vpnc_cm interface outside 558: VPNC CLI: no global (outside) 65001 559: VPNC CLI: no nat (inside) 0 access-list _vpnc_acl 560: VPNC CFG: nat unconfig attempt failed 561: VPNC CLI: nat (inside) 0 access-list _vpnc_acl 562: VPNC INF: IKE trigger request done
Informações Relacionadas
Histórico de revisões
| Revisão | Data de publicação | Comentários |
|---|---|---|
1.0 |
26-Sep-2008 |
Versão inicial |
FeedbackContate a Cisco
- Abrir um caso de suporte
- (É necessário um Contrato de Serviço da Cisco)