Specifying Wireless Settings

Setting Up WLANs and WLAN Users

About WLANs in a Cisco Mobility Express Network

You can create and manage Wireless Local Area Networks (WLANs) through the WLAN Configuration window. Choose Wireless Settings > WLANs.

The total number of active WLANs is displayed at the top of the WLAN Configuration window along with a list of all the WLANs currently configured on the primary AP's controller. This list displays the following details for each WLAN:

Whether the WLAN is enabled or disabled.
Name of the WLAN.
Security Policy on WLAN.
Radio Policy on WLAN.

Guidelines and Limitations for Setting Up WLANs

You can associate up to 16 WLANs with the Cisco Mobility Express controller. Cisco recommends a maximum of 4 WLANs. The controller assigns all the configured WLANs to all the connected APs.
Each WLAN has a unique WLAN ID, a unique profile name, and an SSID.
The WLAN name and SSID can have up to 32 characters.
Each connected AP advertises only the WLANs that are in an Enabled state. The APs do not advertise disabled WLANs.
The controller uses different attributes to differentiate between WLANs with the same SSID.
Peer-to-peer blocking does not apply to multicast traffic.
You cannot map a WLAN to VLAN0, and you cannot map VLANs 1002 to 1006.
Dual-stack clients with static IPv4 addresses are not supported.
When creating WLANs with the same SSID, create a unique profile name for each WLAN.

Adding a WLAN

Procedure

Step 1	Choose Wireless Settings > WLANs. The WLAN Configuration window is displayed.
Step 2	Click Add New WLAN. The Add New WLAN window is displayed.
Step 3	Under the General tab, set the following parameters:
Step 4	Under the WLAN Security tab, set one of the following security authentication options from the Security drop-down list: Open—This option stands for Open authentication, which allows any device to authenticate and then attempt to communicate with an AP. Using open authentication, any wireless device can authenticate with the AP. WPA2 Personal—This option stands for Wi-Fi Protected Access 2 with pre-shared key (PSK). WPA2 Personal is a method used for securing your network with the use of a PSK authentication. The PSK is configured separately both on the controller AP, under the WLAN security policy, and on the client. WPA2 Personal does not rely on an authentication server on your network. This option is used when you do not have an enterprise authentication server. If you choose this option, then specify the PSK in the Shared Key field, and confirm it by specifying it again in the Confirm Shared Key field. The PSK you enter is hidden under asterisks for security purposes. Check the Show Shared Key checkbox to reveal it. WPA2 Enterprise—This option stands for Wi-Fi Protected Access 2, with a local authentication server or a RADIUS server. This is the default option. To have a local authentication method, choose AP in the Authentication Server drop-down list. This option is a Local EAP authentication method that allows users and wireless clients to be authenticated locally. The controller in the primary AP serves as the authentication server and the local user database, which removes dependence on an external authentication server. To have a RADIUS server-based authentication method, choose External Radius in the Authentication Server drop-down list. RADIUS is a client/server protocol that enables communication with a central server to authenticate users and authorize their access to the WLAN. You can specify up to two RADIUS authentication servers. For each server you need to specify the following details: RADIUS IP—IPv4 address of the RADIUS server. RADIUS Port—Enter the communication port of the RADIUS server. The default value is 1812. Shared Secret—Enter the secret key used by the RADIUS server, in ASCII format. Guest—The controller can provide guest user access on WLANs which are specifically designated for use by guest users. To set this WLAN exclusively for guest user access, choose the Security as Guest. You can set the authentication for guest users by choosing one of the following options in the Guest Type drop-down list: WPA2 Personal—This option stands for Wi-Fi Protected Access 2 with pre-shared key (PSK). WPA2 Personal is a method used for securing your network with the use of a PSK authentication. The PSK is configured separately both on the controller AP, under the WLAN security policy, and on the client. WPA2 Personal does not rely on an authentication server on your network. This option is used when you do not have an enterprise authentication server. If you choose this option, then specify the PSK in the Passphrase field, and confirm it by specifying it again in the Confirm Passphrase field. The PSK you enter is hidden under asterisks for security purposes. Check the Show Passphrase checkbox to reveal it. Captive Portal (AP)—Choose this option to set a captive portal which presents one of the following Captive Portal Types to users: Require Username and Password—This is the default option. Choose this option to authenticate guests using the username and password which you can specify for guest users of this WLAN, under Wireless Settings > WLAN Users. For more information, see Viewing and Managing WLAN Users. Web Consent—Choose this option to allow guests access to the WLAN upon acceptance of displayed terms and conditions. This option allows guest users to access the WLAN without entering a username and password. Require Email Address—Choose this option, if you want guest users to be prompted for their e-mail address when attempting to access the WLAN. Upon entering a valid email address, access it provided. This option allows guest users to access the WLAN without entering a username and password. Captive Portal (External Web Server)—Choose this option to have external captive portal authentication, using a web server outside your network. Also specify the URL of the server in the Site URL field. CMX Guest Connect—Choose this option to authenticate guests using the Cisco CMX Connect. Also, specify the URL of your CMX Cloud site in the Site URL field.
Step 5	Under the VLAN & Firewall tab, in the Use VLAN Tagging drop-down list, choose Yes to enable VLAN tagging of packets. Then, choose a VLAN ID from the drop-down list, to use for the tagging. By default VLAN Tagging is disabled. By enabling VLAN Tagging, the chosen VLAN ID is inserted into a packet header in order to identify which VLAN (Virtual Local Area Network) the packet belongs to. This enables the controller to use the VLAN ID to determine which VLAN to send a broadcast packet to, thereby providing traffic separation between VLANs.
Step 6	If you have chosen to enable VLAN Tagging, then you have an option to enable a firewall for the WLAN based on Access Control Lists (ACLs). An ACL is a set of rules used to limit access to a particular WLAN to control data traffic to and from wireless clients or to the controller CPU to control all traffic destined for the CPU. To enable an ACL-based firewall: In the Enable Firewall drop-down list, choose Yes. In the ACL Name field, enter a name for the new ACL. You can enter up to 32 alphanumeric characters. The ACL name must be unique. Click Apply. To set rules for the ACL, click Add Rule. Note that ACL rules are applied to the VLAN. Multiple WLANs can use the same VLAN, hence inheriting ACL rules, if any. Configure a rule for this ACL as follows: From the Action drop-down list, choose Deny to cause this ACL to block packets or Permit to cause this ACL to allow packets. The default is Permit. The controller can permit or deny only IP packets in an ACL. Other types of packets (such as ARP packets) cannot be specified. From the Protocol drop-down list, choose the protocol ID of the IP packets to be used for this ACL. These are the protocol options: Any—Any protocol (this is the default value) TCP—Transmission Control Protocol UDP—User Datagram Protocol ICMP—Internet Control Message Protocol ESP—IP Encapsulating Security Payload AH—Authentication Header GRE—Generic Routing Encapsulation IP in IP—Internet Protocol (IP) in IP (permits or denies IP-in-IP packets) Eth Over IP—Ethernet-over-Internet Protocol OSPF—Open Shortest Path First Other—Any other Internet Assigned Numbers Authority (IANA) protocol. If you choose Other, enter the number of the desired protocol in the Protocol text box. You can find the list of available protocols in the IANA website. In the Dest. IP/Mask field, enter the IP address and netmask of the specific destination. If you have chosen TCP or UDP, you will need specify a Destination Port. This destination port can be used by applications that send and receive data to and from the networking stack. Some ports are designated for certain applications such as Telnet, SSH, HTTP, and so on. From the DSCP drop-down list, choose one of these options to specify the differentiated services code point (DSCP) value of this ACL. DSCP is an IP header text box that can be used to define the quality of service across the Internet. You can choose: Any—Any DSCP (this is the default value) Specific—A specific DSCP from 0 to 63, which you enter in the DSCP edit box Click the Apply icon to commit your changes.
Step 7	Quality of service (QoS) refers to the capability of a network to provide better service to selected network traffic over various technologies. The primary goal of QoS is to provide priority, including dedicated bandwidth, controlled jitter and latency (required by some real-time and interactive traffic), and improved loss characteristics. The Cisco Mobility Express controller supports the following four QoS levels. Under the QoS tab, from the QoS drop-down list, choose one of the following QoS levels: Platinum (Voice)—Ensures a high quality of service for voice over wireless. Gold (Video)—Supports high-quality video applications. Silver (Best Effort)—Supports normal bandwidth for clients. Bronze (Background)—Provides the lowest bandwidth for guest services.
Step 8	Application Visibility classifies applications using the Network-Based Application Recognition (NBAR2) engine, and provides application-level visibility in wireless networks. Application Visibility enables the controller to detect and recognize more than 1000 applications and perform real-time analysis, and monitor network congestion and network link usage. This feature contributes to the Applications By Usage statistic in the Monitoring > Network Summary. To enable Application Visibility, choose Enabled (the default option) from the Application Visibility drop-down list. Otherwise, choose Disabled.
Step 9	Click Apply.

What to do next

You can proceed to create or edit user accounts for a WLAN. See Viewing and Managing WLAN Users.

Enabling and Disabling a WLAN

Procedure

Step 1

Choose Wireless Settings > WLANs.

The WLAN Configuration window is displayed.

Step 2

Click the Edit icon adjacent to the WLAN you want to enable or disable.

The Edit WLAN window is displayed.

Step 3

Choose General > Admin State and select Enabled or Disabled, as required.

Step 4

Click Apply.

Note

Clicking Apply after creating a new WLAN or editing an existing one always enables the WLAN irrespective of whether it was previously enabled or disabled.

Editing and Deleting a WLAN

Choose Wireless Settings > WLANs. In the window that is displayed, perform one of the following actions:

To edit a WLAN, click the Edit icon adjacent to it.
To delete a WLAN, click the Delete icon adjacent to it.

Viewing and Managing WLAN Users

To view and manage WLAN users, choose Wireless Settings > WLAN Users.

The WLAN Users window is displayed, along with the total number of WLAN users configured on the controller. It also lists all the WLAN users in the network along with the following details for each:

User name—Name of the WLAN user.
Guest user—If this checkbox is selected, then this is a guest user account with a limited validity of only 86400 seconds (or 24 hours) from the time of its creation.
WLAN Profile—The WLANs that this user can connect to.
Password—The password to be used when connecting to a WLAN.
Description—Additional details or comments about the user.

You can view and manage WLAN users only for the WPA2 Enterprise with Local Server setup. To use your Cisco Mobility Express wireless network, a wireless client should connect to a WLAN in the network. To connect to a WLAN, the wireless client will have to use the user credentials set for that WLAN. If this WLAN uses WPA2-Personal as a Security Policy, then the user must provide the appropriate WPA2-PSK set for that WLAN on the Controller AP. If the Security Policy is set to WPA2-Enterprise, the user must provide a valid user identity and the corresponding password set in the RADIUS user database.

Adding a WLAN User

To add a WLAN user, click Add WLAN User, and then fill in the following details:

User name—Specify a name for WLAN user account.
Guest user—Select this checkbox if this is meant to be a guest WLAN user account. You can also specify the validity of this account from the time of its creation, in seconds, the Lifetime field. The default value is 86400 seconds (that is, 24 hours). You can specify a lifetime value from 60 to 31536000 seconds (that is, 1 minute to 1 year).
WLAN Profile—Select the WLAN that this user can connect to. From the drop-down list, choose a particular WLAN, or choose Any WLAN to apply this account for all WLANs set up on the controller.

This drop-down list is populated with the WLANs which have been configured under Wireless Settings > WLANs.

For information on adding WLANs, see Adding a WLAN.
Password—The password to be used when connecting to a WLAN.
Description—Additional details or comments on the user.

Editing a WLAN User

To edit a WLAN user, click the Edit icon adjacent to the WLAN user whose details you want to edit and make the necessary changes.

Deleting a WLAN User

To delete a WLAN user, click the Delete icon adjacent to the WLAN user you want to delete. and then click Ok in the confirmation dialog box.

Managing Associated Access Points

Choose Wireless Settings > Access Points. The Access Points Administration window is displayed. The number of APs associated with the controller is displayed at the top of the window, along with the following details:

Manage—The icons shown below indicate whether the AP is acting as Primary Controller (or Primary AP) or a subordinate AP.

Figure 1. Primary Controller (or Primary AP) icon

Figure 2. Subordinate AP icon
Location—Location of the AP.
Name—Name of the AP.
IP Address—IP address of the AP.
AP MAC—The MAC address of the AP.
Up Time—Shows how long the AP has been associated to the controller.
AP Model—The model number of the access point.

Administering Access Points

Procedure

Step 1

Choose Wireless Settings > Access Points.

The Access Points Administration window is displayed. You can only administer those APs that are associated to the controller.

Step 2

Click the Edit icon adjacent to the AP you want to manage.

The Edit window with the General tab is displayed.

Step 3

Under the General tab, you can edit the following AP parameters:

Operating Mode and Make me Controller—For a primary AP, the Operating Mode field shows AP & Controller. For other associated APs, this field shows AP Only.

The Make me Controller button is available only for subordinate APs that are capable of participating in the primary Election process. Click this button to make this AP the primary AP.
IP Configuration—Choose Obtain from DHCP to let the IP address of the AP be assigned by a DHCP server on the network, or choose to have a Static IP address. If you choose to have a static IP address, then you can edit the IP Address, Subnet Mask, and Gateway fields.
AP Name—Edit the name of the AP. This is a free text field.
Location—Edit a location for the AP. This is a free text field.

The following non-editable AP parameters are also displayed under the General tab:

AP MAC address
AP Model number
IP Address of the access point (non-editable only if Obtain from DHCP has been selected).
Subnet mask (non-editable only if Obtain from DHCP has been selected).
Gateway (non-editable only if Obtain from DHCP has been selected).

Step 4

(Only for the primary AP) Under the Controller tab, you can manually edit the following controller parameters for the integrated Mobility Express wireless LAN controller:

IP Address—This IP address decides the login URL to the controller's web interface. The URL is in the format https://<ip address>. If you change this IP address, the login URL also changes.
Subnet Mask
Country Code

Step 5

Under the Radio 1 and Radio 2 tabs you can set the following parameters.

Note

The Radio 1 tab corresponds to the 2.4 GHz (802.11 b/g/n) radio on all APs, except the Cisco Aironet 3800 and 2800 series APs. On these APs, it can be set to either 2.4 GHz (802.11 b/g/n) or 5 GHz (802.11a/n/ac). The Radio 2 tab corresponds to only the 5 GHz (802.11a/n/ac) radio on all APs.

The radio tab name also indicates the operational radio band within brackets.


Parameter	Description
Admin Mode	Enable or Disable the corresponding radio on the AP.
Band	Only present for Radio 1. It is set to 2.4 GHz by default. For 3800 and 2800 series APs you can change it to 5 GHz.
Channel	For 2.4 GHz, you can set this to Automatic, or set a value from 1 to 11. Selecting Automatic enables Dynamic Channel Assignment. This means that channels are dynamically assigned to each AP, under the control of the primary AP. This prevents neighboring APs from broadcasting over the same channel and prevents interference and other communication problems. For the 2.4 GHz radio, 11 channels are offered in the U.S. and up to 14 in other parts of the world. However, only 1-6-11 can be considered non-overlapping if they are used by neighboring APs. Assigning a specific value statically assigns a channel to that AP.	For 5 GHz, you can set this to Automatic, 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 132, 136, 140, 149, 153, 157, 161, or 165. For the 5 GHz radio, up to 23 non-overlapping channels are offered. Assigning a specific value statically assigns a channel to that AP.
Channel Width	The channel width for 2.4 GHz can only be 20 MHz.	The channel width for 5 GHz can be set to Automatic, or to 20, 40, or 80 MHz, if channel bonding is used. Channel bonding groups the channels by 2 or 4 for a single radio stream. This increases the speed and the throughput. Because the number of channels is insufficient in 2.4 GHz, channel bonding cannot be used to enable multiple non-overlapping channels.
Transmit Power	You can set it to Automatic, or set a value from 1 to 8. This is a logarithmic scale of the transmit power, which is the transmission energy used by the AP, with 1 being the highest, 2 being half of it, 3 being 1/4th, and so on. Selecting Automatic adjusts the radio transmitter output power based on the varying signal level at the receiver. This allows the transmitter to operate at less than maximum power for most of the time; when fading conditions occur, transmit power will be increased as required until the maximum is reached.

Step 6

Click Apply to save your changes and exit.

Setting a Login Page for WLAN Guest Users

Before you begin, follow these steps to provide guest users with access to your network:

Set up a new WLAN or decide on an existing WLAN, to which you will provide access for guest users.

You can also specifically set up a WLAN exclusively for guest access. This is done by setting the WLAN Security as Guest for that WLAN. For more information, see Adding a WLAN.
Set up a guest user account. Go to Wireless Settings > WLAN Users, and set up an account with the Guest User check box selected. For more information, see Viewing and Managing WLAN Users.

You can present the Guest users of your WLAN with either of the following login page options:

A simple minimalist default login page with a few modification options. To configure this, see Setting the Default Login Page.
A customized login page uploaded into the controller. To configure this, see Setting a Customized Login Page.

Setting the Default Login Page

Right out of the box, the default login page contains a Cisco logo and Cisco-specific text. You can choose to modify this default login page as described here.

Procedure

Step 1	Choose Wireless Settings > Guest WLAN. The Guest WLAN page is displayed. The number of Guest WLANs currently set up in the network is displayed at the top of the page.
Step 2	To use the default login page, in the Page Type drop-down list, choose Internal.
Step 3	Set the following parameters to modify the default internal login page: Display Cisco Logo—This field is set to Yes by default. To hide the Cisco logo that appears at the top-right corner of the default window, choose No. This field is set to Yes by default. However, you do not have an option to display any other logo. Redirect URL After Login— To have guest users redirected to a particular URL (such as the URL for your company) after login, enter the URL in this field. You can enter up to 254 characters. Page Headline—The default headline is Welcome to the Cisco Wireless Network. To create your own headline on the login page, enter the desired text in this field. You can enter up to 127 characters. Page Message— The default message is Cisco is pleased to provide the Wireless LAN infrastructure for your network. Please login and put your air space to work. To create your own message on the login page, enter the desired text in this field, You can enter up to 2047 characters.
Step 4	Click Apply.

Setting a Customized Login Page

You can create a custom login page on a computer, compress the page and image files into a .TAR file, and then upload it to the controller. The upload is done via HTTP.

Note

When you save the controller's configuration, it does not include extra files or components, such as the web authentication bundle, that you download and store on your controller. Hence, manually save external backup copies of such files.

Note

Cisco TAC is not responsible for creating a custom web authentication bundle.

Before you begin

Create a custom login page on a computer while ensuring the following:
- Name the login page login.html. The controller prepares the web authentication URL based on this name. If the server does not find this file after the web authentication bundle has been untarred, the bundle is discarded, and an error message appears.
- The page should not contain more than 5 elements (including HTML, CSS, and Images). This is because the internal controller web server implements a DoS protection mechanism that limits each client to open a maximum of 5 (five) concurrent TCP connections depending on the load. Some browsers may try to open more than 5 TCP sessions at the same time if the page contains more elements and this may result in the page loading slowly depending on how the browser handles the DoS protection.
- Include input text boxes for the username and the password.
- Extract and set the action URL in the page from the original URL.
- Include scripts to decode the return status code.
- All paths used in the main page (to refer to images, for example) are of relative type.
- No filenames within the bundle are longer than 30 characters.
Compress the page and image files into a ,TAR file. The maximum allowed size of the files in their uncompressed state is 1 MB.

Cisco recommends that you use an application that complies with GNUstandards to compress the .TAR file (also referred to as the web authentication bundle.). If you load a web authentication bundle with a .TAR compression application that is not GNU compliant, the controller will not be able to extract the files in the bundle.

The .TAR file enters the controller’s file system as an untarred file.

Note

If you have a complex customized web authentication bundle which does not comply with the aforementioned prerequisites, then Cisco recommends that you host it on an external web server. See (..)

Procedure

Step 1	Choose Wireless Settings > Guest WLAN. The Guest WLAN page is displayed. The number of Guest WLANs currently set up in the network is displayed at the top of the page.
Step 2	To upload a customized login page into the controller, in the Page Type drop-down list, choose Customized.
Step 3	Click Upload, to browse to and upload the .TAR file of the customized web authentication bundle.
Step 4	If you want the user to be directed to a particular URL (such as the URL for your company) after login, enter that URL in the Redirect URL After Login text box. You can enter up to 254 characters.
Step 5	Click Apply. Click Preview to view your customized web authentication login page.

Managing the Internal DHCP Server

The Cisco Mobility Express controller contains an internal DHCP server which manages the DHCP addresses assigned to network devices associated with it. The IP addresses assigned to client devices are not preserved across reboots. This enables reuse of IP addresses across multiple client devices. To resolve IP address conflicts, client devices need to release their existing IP address and request for a new one.

Starting Cisco Wireless Release 8.3, you can configure the internal DHCP server using the Cisco Mobility Express web interface.

Add DHCP Pool

Procedure

Step 1

Choose Wireless Settings > DHCP Server.

The DHCP Configuration window appears.

Step 2

Click Add New Pool.

The Add DHCP Pool window appears.

Step 3

In the Pool Name field, enter the desired name.

The DHCP pool name must meet the following conditions:

Step 4

From the Active drop-down list, select either Enabled or Disabled.

The default setting is Disabled.

Step 5

In the VLAN ID field, specify the VLAN ID for the DHCP Pool.

Note

Select the Management Network checkbox to set the management interface IP address of the Cisco Mobility Express controller as the DHCP server IP address.

Step 6

In the Network/Mask fields, specify the IP address of the network and the subnet mask.

Step 7

In the Start IP field, specify the starting IP address for the network.

Step 8

In the End IP field, specify the ending IP address for the network.

Step 9

In the Default Gateway field, specify the IP address for the default gateway to the network.

Note

The default gateway, starting IP address, and the ending IP address must be in the same subnet.

Step 10

In the Domain Name field, enter the desired name.

The domain name must meet the following conditions:

Step 11

From the Name Servers drop-down list, select either OpenDNS or User Defined.

The default setting is OpenDNS.

Step 12

Enter the IP address for the name servers in the provided fields.

Edit DHCP Pool

Procedure

Step 1	Choose Wireless Settings > DHCP Server. The DHCP Configuration window appears.
Step 2	Click the <edit_icon.gif> icon in the row containing the DHCP Pool whose details you wish to modify. The desired row in the DHCP Pool table becomes editable (or the Edit DHCP Pool window appears.)
Step 3	In the DHCP Pool table, make the desired modifications inline (or in the Edit DHCP Pool window).
Step 4	Click Apply. The DHCP Pool table is refreshed and the updated entry appears in this table.

Delete DHCP Pool

Procedure

Step 1

Choose Wireless Settings > DHCP Server.

The DHCP Configuration window appears.

Step 2

Click the X icon in the row containing the DHCP pool you wish to delete.

A warning message appears.

Step 3

Click Yes in the pop-up window.

The DHCP pool table is refreshed and the deleted entry is removed from this table.

View DHCP Lease Details

Procedure

Step 1

Choose Wireless Settings > DHCP Server.

The DHCP Configuration window appears.

Step 2

Under the DHCP pool table, click DHCP Leases.

The DHCP Pool Information window appears where you can view details such as the host name, its MAC address, assigned IP address, and lease expiry details.

Note

You can release a specific IP address by removing the lease to the host in the corresponding entry of the DHCP Pool Information table.

Export Details of Leased IP Addresses

Procedure

Step 1	Choose Wireless Settings > DHCP Server. The DHCP Configuration window appears.
Step 2	Under the DHCP pool table, click DHCP Leases. The DHCP Pool Information window appears.
Step 3	Below the DHCP Pool Information table, click Export.
Step 4	Choose the format in which you wish to export the details of the leased IP addresses and the corresponding hosts.

Release Leased IP Address

Procedure

Step 1	Choose Wireless Settings > DHCP Server. The DHCP Configuration window appears.
Step 2	Under the DHCP pool table, click DHCP Leases. The DHCP Pool Information window appears.
Step 3	In the row containing the the host assigned the leased IP address you wish to delete, click the <release_icon.gif> icon. A warning message appears.
Step 4	You can release a specific IP address by removing the lease to in the corresponding entry of the DHCP Pool Information table.
Step 5	Click Yes in the pop-up window. The DHCP Pool Information table is refreshed and the deleted entry is removed from this table.

Cisco Mobility Express Configuration and User Guide, Cisco Wireless Release 8.3

Bias-Free Language

Results

Chapter: Specifying Wireless Settings

Specifying Wireless Settings

About WLANs in a Cisco Mobility Express Network

Guidelines and Limitations for Setting Up WLANs

Adding a WLAN

Procedure

What to do next

Enabling and Disabling a WLAN

Procedure

Editing and Deleting a WLAN

Viewing and Managing WLAN Users

Adding a WLAN User

Editing a WLAN User

Deleting a WLAN User

Managing Associated Access Points

Administering Access Points

Procedure

Setting a Login Page for WLAN Guest Users

Setting the Default Login Page

Procedure

Setting a Customized Login Page

Before you begin

Procedure

Managing the Internal DHCP Server

Add DHCP Pool

Procedure

Edit DHCP Pool

Procedure

Delete DHCP Pool

Procedure

View DHCP Lease Details

Procedure

Export Details of Leased IP Addresses

Procedure

Release Leased IP Address

Procedure

Was this Document Helpful?

Contact Cisco