Installation — All Nodes

Installation Media

The installation for Unified Intelligence Center is delivered on DVD media. Run the DVD installation on each node, and use the same DVD for all nodes.


Note

All nodes must be running the same version of Cisco Unified Intelligence Center.

Before You Begin

Every installation begins with an optional pre-install media check, which includes a hardware check. You then make your product deployment selection before continuing to the basic install configuration.

Procedure

Step 1

Mount ISO to the virtual DVD drive. Then restart or power on the server so that it boots from the DVD.

You see messages as the pre-install script runs. When the pre-install script ends, the DVD Found screen opens.

Step 2

In the DVD Found screen, you have the option to perform a media check to verify the integrity of the DVD.

If you want to check the media:

  1. Select Yes to begin the verification of the media integrity.

    Note 

    The media check can take up to an hour. If the media check for the Controller passes, you can safely skip the media check when you install the Members.

  2. If the media check passes, select OK. The Product Deployment Selection screen appears, and you can continue to Step 3.

    If the media check fails, the DVD is ejected and the installation terminates. Contact your support provider for assistance.

If you want to skip the media check:

  1. Select No. The Product Deployment Selection appears.

  2. Proceed to Step 3.

Step 3

Choose one of the following options:

  • Cisco Unified Intelligence Center
  • Live Data
  • Cisco Identity Service (IdS)
  • Cisco Unified Intelligence Center with Live Data and IdS
Note 

  • For the 2000 agent reference design, choose the co-resident deployment option Cisco Unified Intelligence Center with Live Data and IdS; and then select OK. The Cisco Unified Intelligence Center, Live Data, and IdS option installs Cisco Unified Intelligence Center, Live Data and Cisco Identity Service (IdS) on the same server.

  • For all other deployments, select one of the standalone install options. For example, select Cisco Unified Intelligence Center, Live Data, or Cisco Identity Service (IdS). Then select OK.

Step 4

Click OK to initiate a check for hard drive sanity, during which the installation checks for a supported hardware platform with the correct number of disks.

A successful hardware check opens the Proceed with Install screen. The Proceed with Install screen shows the version of the product that is currently on the hard drive (if any) and the version of the product that is on the DVD. For the initial installation, the version on the hard drive shows NONE.

Note 
If the server hardware is unsupported, a message appears indicating that the installation cannot proceed, and the installation halts. If you require assistance understanding the message, write it down to facilitate your conversation with your support provider. See Contact Center Enterprise Compatibility Matrix at https://www.cisco.com/c/en/us/support/customer-collaboration/unified-contact-center-enterprise/products-device-support-tables-list.html for details on supported hardware.
Step 5

Select Yes on the Proceed with Install screen.

The Platform Installation Wizard screen appears.
Step 6

In the Platform Installation Wizard screen, select Proceed to open the Apply Patch screen.

Step 7

Select No at the Apply Patch screen. Do not apply patches from the Installation wizard. See About Upgrades for instructions on upgrading Unified Intelligence Center software with Engineering Specials, Minor Releases, and Maintenance Releases.

Your selection of No opens the Basic Install screen.

If you select Yes by mistake and open the Apply Patch screen, select Back. Then choose one of the following options:

  • To enter your configuration information manually and have the installation program install the configured software on the server, choose Proceed and continue with this procedure.

  • To do any of the following tasks, choose Skip; then continue with the Entering Preexisting Configuration Information procedure:

    • Manually configure the software that is preinstalled on your server — In this case you do not need to install the software, but you must configure the preinstalled software.

    • Perform an unattended installation — In this case, you provide preexisting configuration information on a USB key or floppy disk.

    • Install the software before manually configuring it — In this case the installation program installs the software, then prompts you to configure it manually. You can choose Skip if you want to preinstall the application on all your servers first and then enter information at a later time. This method might cause you to spend more time performing the installation than the other methods.

Step 8

Select Continue at the Basic Install screen to enter the configuration screens.

Enter Pre-Existing Configuration Information

Start here if you have a server that has the product pre-installed or if you chose Skip in the Platform Installation Wizard window.

Procedure

Step 1

After the system restarts, the Pre-existing Installation Configuration window displays.

Step 2

If you have pre existing configuration information (Created by Answer File Generator) in a floppy disc or a USB key, insert the disc or the USB key now and choose Continue. The installation wizard will read the configuration information during the installation process.

Note 

If a popup window states that the system detected new hardware, press any key and then choose Install from the next window.

The Platform Installation Wizard window displays.

Step 3

To continue with the Platform Installation Wizard, choose Proceed.

Step 4

In the Basic Install window, choose Continue. Continue with the "Configure basic install" section.

Configure Basic Install

The basic install launches a series of screens that present questions and options pertinent to the platform and the setup configuration. There is online help for each wizard screen.


Note
You can change many of the basic installation configuration settings after the installation using the Set commands in the Command Line Interface (CLI). The CLI is documented in the Administration Console User Guide for Cisco Unified Intelligence Center.

The first Basic Install wizard screen is Timezone Configuration.

Procedure

Step 1

In the Timezone Configuration screen:

  1. Use the down arrow to select the local timezone that most closely matches where your server is located. You can also type the initial character of the timezone to move to that item in the list. The timezone field is based on country/city and is mandatory. Setting it incorrectly can affect system operation.

    Note 

    Use the same timezone for all nodes.

  2. Select OK to open the Auto Negotiation Configuration screen.

Step 2

In the Auto Negotiation Configuration screen, select whether or not you want to use automatic negotiation for the settings of the Ethernet network interface card (NIC).

If

Then

You want to disable auto-negotiation and specify NIC speed and duplex settings.

Select No to open the NIC Speed and Duplex Configuration screen, where you can manually configure the settings.

Proceed to Step 3.

The ethernet network interface card (NIC) attached to your hub or Ethernet switch supports automatic negotiation.

Select Yes to open the MTU Configuration screen.

Proceed to Step 4.

Step 3

In the NIC Speed and Duplex Configuration screen, configure settings as follows:

  1. Specify the speed of the Network Interface (NIC) card in megabits per second. Speed options are 10 or 100.

  2. Specify the duplex setting of the server NIC. Options are Full or Half.

  3. Select OK to open the MTU Configuration screen.

Step 4

In the MTU Configuration screen, select No to keep the default setting for Maximum Transmission Units (1500). If you do not accept the default and configure the MTU size incorrectly, your network performance can be affected.

Your selection of No opens the DHCP Configuration screen.

Step 5

In the DHCP Configuration screen, select No to open the Static Network Configuration screen.

Step 6

At the Static Network Configuration screen, enter static network configuration values as follows, referring to the Configuration Worksheet if necessary:

  1. Enter the Host Name.

  2. Enter the IP Address.

  3. Enter the IP Mask.

  4. Enter the GW Address,

  5. Select OK to open the Domain Name System (DNS) Client Configuration screen.

Step 7

Select Yes to enable the Domain Name System (DNS) Client.

Step 8

Enter your DNS client information as follows, if necessary:

  1. Configuration Worksheet Enter the Primary DNS (mandatory).

  2. Enter the Secondary DNS (optional).

  3. Enter the Domain (mandatory).

  4. Select OK to open the Administrator Login Configuration screen.

Step 9

In the Administrator Login Configuration screen:

  1. Enter the ID for the System Administrator.

  2. Enter and then confirm the password for the administrator.

  3. Select OK to open the Certificate Information screen.

Step 10

In the Certificate Information screen:

  1. Enter data to create your Certificate Signing Request—Organization, Unit, Location, State, and Country.

  2. Select OK to open the First Node Configuration screen. ("Is this server the First Node in the cluster?")

Step 11

In the First Node Configuration screen, specify whether you are configuring the first node (the Controller).

If

Then

You are installing and configuring the primary node (the Controller).

Select Yes to open the Network Time Protocol Client Configuration screen.

Continue to Controller Configuration.

You are installing and configuring a secondary node (a Unified Intelligence Center Member).

Select No to open the First Node Configuration Warning screen.

Continue to Complete Configuration for Member Node .