Cisco UCS C-Series Integrated Management Controller GUI Configuration Guide, Release 3.1

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Book Contents
Find Matches in This Book
Available Languages
Download Options

Book Title

Cisco UCS C-Series Integrated Management Controller GUI Configuration Guide, Release 3.1

Chapter Title

Configuring Communication Services

Results

Updated:
August 16, 2017

Chapter: Configuring Communication Services

Configuring Communication Services

This chapter includes the following sections:

Configuring HTTP

Before you begin

You must log in as a user with admin privileges to perform this task.

Procedure

Step 1

In the Navigation pane, click the Admin menu.

Step 2

In the Admin menu, click Communication Services.

Step 3

In the HTTP Properties area, update the following properties:

Name Description

HTTP/S Enabled check box

Whether HTTP and HTTPS are enabled on the Cisco IMC.

Redirect HTTP to HTTPS Enabled check box

If enabled, all attempts to communicate via HTTP are redirected to the equivalent HTTPS address.

We strongly recommend that you enable this option if you enable HTTP.

HTTP Port field

The port to use for HTTP communication. The default is 80.

HTTPS Port field

The port to use for HTTPS communication. The default is 443

Session Timeout field

The number of seconds to wait between HTTP requests before the Cisco IMC times out and terminates the session.

Enter an integer between 60 and 10,800. The default is 1,800 seconds.

Max Sessions field

The maximum number of concurrent HTTP and HTTPS sessions allowed on the Cisco IMC.

This value may not be changed.

Active Sessions field

The number of HTTP and HTTPS sessions currently running on the Cisco IMC.

Step 4

Click Save Changes.

Configuring SSH

Before you begin

You must log in as a user with admin privileges to configure SSH.

Procedure

Step 1

In the Navigation pane, click the Admin menu.

Step 2

In the Admin menu, click Communication Services.

Step 3

In the SSH Properties area, update the following properties:

Name Description

SSH Enabled check box

Whether SSH is enabled on the Cisco IMC.

SSH Port field

The port to use for secure shell access. The default is 22.

SSH Timeout field

The number of seconds to wait before the system considers an SSH request to have timed out.

Enter an integer between 60 and 10,800. The default is 1,800 seconds.

Max Sessions field

The maximum number of concurrent SSH sessions allowed on the Cisco IMC.

This value may not be changed.

Active Sessions field

The number of SSH sessions currently running on the Cisco IMC.

Step 4

Click Save Changes.

Configuring XML API

XML API for Cisco IMC

The Cisco Cisco IMC XML application programming interface (API) is a programmatic interface to Cisco IMC for a C-Series Rack-Mount Server. The API accepts XML documents through HTTP or HTTPS.

For detailed information about the XML API, see Cisco UCS Rack-Mount Servers Cisco IMC XML API Programmer’s Guide.

Enabling the XML API

Before you begin

You must log in as a user with admin privileges to perform this task.

Procedure

Step 1

In the Navigation pane, click the Admin menu.

Step 2

In the Admin menu, click Communication Services.

Step 3

In the XML API Properties area, update the following properties:

Name Description

XML API Enabled check box

Whether API access is allowed on this server.

Max Sessions field

The maximum number of concurrent API sessions allowed on the Cisco IMC.

This value may not be changed.

Active Sessions field

The number of API sessions currently running on the Cisco IMC.

Step 4

Click Save Changes.

Enabling Redfish

Before you begin

You must be logged in as admin to perform this action.

Procedure

Step 1

In the Navigation pane, click the Admin tab.

Step 2

On the Admin tab, click Communications Services.

Step 3

In the Redfish Properties area, update the following properties:

Name Description

XML API Enabled check box

Whether API access is allowed on this server.

Max Sessions field

The maximum number of concurrent API sessions allowed on the Cisco IMC.

This value may not be changed.

Active Sessions field

The number of API sessions currently running on the Cisco IMC.

Step 4

Click Save Changes.

Configuring IPMI

IPMI Over LAN

Intelligent Platform Management Interface (IPMI) defines the protocols for interfacing with a service processor embedded in a server platform. This service processor is called a Baseboard Management Controller (BMC) and resides on the server motherboard. The BMC links to a main processor and other on-board elements using a simple serial bus.

During normal operations, IPMI lets a server operating system obtain information about system health and control system hardware. For example, IPMI enables the monitoring of sensors, such as temperature, fan speeds and voltages, for proactive problem detection. If server temperature rises above specified levels, the server operating system can direct the BMC to increase fan speed or reduce processor speed to address the problem.

Configuring IPMI over LAN

Configure IPMI over LAN when you want to manage the Cisco IMC with IPMI messages.


Note

  • If you would want to run IPMI commands without issuing an encryption key, set the Encryption Key field in Cisco IMC to any even number of zeroes and save. This allows you to issue IPMI commands without including an encryption key.

  • You are only allowed a maximum of four concurrent IPMI sessions.

Before you begin

You must log in as a user with admin privileges to perform this task.

Procedure

Step 1

In the Navigation pane, click the Admin menu.

Step 2

In the Admin menu, click Communication Services.

Step 3

In the IPMI over LAN Properties area, update the following properties for BMC 1, BMC 2, CMC 1, or CMC 2:

Name Description

Enabled check box

Whether IPMI access is allowed on this server.

Privilege Level Limit drop-down list

The highest privilege level that can be assigned to an IPMI session on this server. This can be one of the following:

  • read-only—IPMI users can view information but cannot make any changes. If you select this option, IPMI users with the "Administrator", "Operator", or "User" user roles can only create read-only IPMI sessions, regardless of their other IPMI privileges.

  • user—IPMI users can perform some functions but cannot perform administrative tasks. If you select this option, IPMI users with the "Administrator" or "Operator" user role can create user and read-only sessions on this server.

  • admin—IPMI users can perform all available actions. If you select this option, IPMI users with the "Administrator" user role can create admin, user, and read-only sessions on this server.

Encryption Key field

The IPMI encryption key to use for IPMI communications.

Randomize button

Enables you to change the IPMI encryption key to a random value.

Step 4

Click Save Changes.

Configuring SNMP

Configuring SNMP Properties

Before you begin

You must log in as a user with admin privileges to perform this task.

Procedure

Step 1

In the Navigation pane, click the Admin menu.

Step 2

In the Admin menu, click Communication Services.

Step 3

In the Communications Services pane, click the SNMP tab.

Step 4

In the SNMP Properties area, update the following properties:

Name Description

SNMP Enabled check box

Whether this server sends SNMP traps to the designated host.

Note 

After you check this check box, you need to click Save Changes before you can configure SNMP users or traps.

SNMP Port field

The port on which Cisco IMC SNMP agent runs.

Enter an SNMP port number within the range 1 to 65535. The default port number is 161.

Note 
The port numbers that are reserved for system calls, such as 22,23,80,123,443,623,389,636,3268,3269 and 2068, cannot be used as an SNMP port.

Access Community String field

The default SNMP v1 or v2c community name Cisco IMC includes on any SNMP get operations.

Enter a string up to 18 characters.

SNMP Community Access drop-down list

This can be one of the following:

  • Disabled — This option blocks access to the information in the inventory tables.

  • Limited — This option provides partial access to read the information in the inventory tables.

  • Full — This option provides full access to read the information in the inventory tables.

Note 
SNMP Community Access is applicable only for SNMP v1 and v2c users.

Trap Community String field

The name of the SNMP community group used for sending SNMP trap to other devices.

Enter a string up to 18 characters.

Note 
This field is visible only for SNMP v1 and v2c users. SNMP v3 users need to use SNMP v3 credentials.

System Contact field

The system contact person responsible for the SNMP implementation.

Enter a string up to 64 characters, such as an email address or a name and telephone number.

System Location field

The location of the host on which the SNMP agent (server) runs.

Enter a string up to 64 characters.

SNMP Input Engine ID field

User-defined unique identification of the static engine.

SNMP Engine ID field

Unique string to identify the device for administration purpose. This is generated from the SNMP Input Engine ID if it is already defined, else it is derived from the BMC serial number.

Step 5

Click Save Changes.

What to do next

Configure SNMP trap settings.

Configuring SNMP Trap Settings

Before you begin

You must log in as a user with admin privileges to perform this task.

Procedure

Step 1

In the Navigation pane, click the Admin menu.

Step 2

In the Admin menu, click Communication Services.

Step 3

In the Communications Services pane, click the SNMP tab.

Step 4

Click on Trap Destinations tab.

Step 5

In the Trap Destinations area, you can perform one of the following:

  • Select an existing user from the table and click Modify Trap.

  • Click Add Trap to create a new user.

Note 

If the fields are not highlighted, select Enabled.

Step 6

In the Trap Details dialog box, complete the following fields:

Name Description

ID field

The trap destination ID. This value cannot be modified.

Enabled check box drop-down list

If checked, then this trap is active on the server.

Version drop-down list

The SNMP version and model used for the trap. This can be one of the following:

  • V2

  • V3

Trap Type radio button drop-down list

The type of trap to send. This can be one of the following:

  • Trap: If this option is chosen, the trap will be sent to the destination but you do not receive any notifications.

  • Inform: You can choose this option only for V2 users. If chosen, you will receive a notification when a trap is received at the destination.

User drop-down list

The drop-down list displays all available users, select a user from the list.

Trap Destination Address field

Address to which the SNMP trap information is sent. You can set an IPv4 or IPv6 address or a domain name as the trap destination.

Port

The port the server uses to communicate with the trap destination.

Enter a trap destination port number within the range 1 to 65535.

Step 7

Click Save Changes.

Step 8

If you want to delete a trap destination, select the row and click Delete.

Click OK in the delete confirmation prompt.

Sending a Test SNMP Trap Message

Before you begin

You must log in as a user with admin privileges to perform this task.

Procedure

Step 1

In the Navigation pane, click the Admin menu.

Step 2

In the Admin menu, click Communication Services.

Step 3

In the Communication Services pane, click SNMP.

Step 4

In the Trap Destinations area, select the row of the desired SNMP trap destination.

Step 5

Click Send SNMP Test Trap.

An SNMP test trap message is sent to the trap destination.

Note 

The trap must be configured and enabled in order to send a test message.

Managing SNMP Users

Before you begin

  • You must log in as a user with admin privileges to perform this task.

  • SNMP must be enabled.

Procedure

Step 1

In the Navigation pane, click the Admin menu.

Step 2

In the Admin menu, click Communication Services.

Step 3

In the Communications Services pane, click the SNMP tab.

Step 4

In the User Settings area, update the following properties:

Name Description

Add User button

Click an available row in the table then click this button to add a new SNMP user.

Modify User button

Select the user you want to change in the table then click this button to modify the selected SNMP user.

Delete User button

Select the user you want to delete in the table then click this button to delete the selected SNMP user.

ID column

The system-assigned identifier for the SNMP user.

Name column

The SNMP user name.

Auth Type column

The user authentication type.

Privacy Type column

The user privacy type.

Step 5

Click Save Changes.

Configuring SNMP Users

Before you begin

  • You must log in as a user with admin privileges to perform this task.

  • SNMP must be enabled.

Procedure

Step 1

In the Navigation pane, click the Admin menu.

Step 2

In the Admin menu, click Communication Services.

Step 3

In the Communications Services pane, click the SNMP tab.

Step 4

In the User Settings area, perform one of the following actions:

  • Select an existing user from the table and click Modify User.
  • Select a row in the Users area and click Add User to create a new user.
Step 5

In the SNMP User Details dialog box, update the following properties:

Name Description

ID field

The unique identifier for the user. This field cannot be changed.

Name field

The SNMP username.

Enter between 1 and 31 characters or spaces.

Note 

Cisco IMC automatically trims leading or trailing spaces.

Security Level drop-down list

The security level for this user. This can be one of the following:

  • no auth, no priv—The user does not require an authorization or privacy password.

  • auth, no priv—The user requires an authorization password but not a privacy password. If you select this option, Cisco IMC enables the Auth fields described below.

  • auth, priv—The user requires both an authorization password and a privacy password. If you select this option, Cisco IMC enables the Auth and Privacy fields.

Auth Type drop-down

The authorization type. This can be one of the following:

  • MD5

  • SHA

Auth Password field

The authorization password for this SNMP user.

Enter between 8 and 64 characters or spaces.

Note 

Cisco IMC automatically trims leading or trailing spaces.

Confirm Auth Password field

The authorization password again for confirmation purposes.

Privacy Type drop-down

The privacy type. This can be one of the following:

  • DES

  • AES

Privacy Password field

The privacy password for this SNMP user.

Enter between 8 and 64 characters or spaces.

Note 

Cisco IMC automatically trims leading or trailing spaces.

Confirm Privacy Password field

The authorization password again for confirmation purposes.

Step 6

Click Save Changes.

Step 7

If you want to delete a user, select the user and click Delete User.

Click OK in the delete confirmation prompt.

Configuring a Server to Send Email Alerts Using SMTP

The Cisco IMC supports email-based notification of server faults to recipients without relying on the SNMP. The system uses the Simple Mail Transfer Protocol (SMTP) to send server faults as email alerts to the configured SMTP server.

A maximum of four recipients is supported.

Configuring SMTP Server For Receiving Email Alerts

Configure the SMTP properties and add email recipients on the Mail Alert tab to receive email notifications for server faults.

Before you begin

You must log in as a user with admin privileges to perform this task.

Procedure

Step 1

Step 2

In the Admin menu, click Communication Services.

Step 3

In the Communications Services pane, click the Mail Alert tab.

Step 4

In the SMTP Properties area, update the following properties.

Name Description

SMTP Enabled checkbox

If checked, it enables the SMTP service.

SMTP Server Address field

Allows you to enter the SMTP server address.

SMTP Port field

Allows you to enter the SMTP port number. The default port number is 25.

Minimum Severity to Report drop-down list

Allows you to choose the minimum severity level for receiving the email alert. This can be one of the following:

  • Condition

  • Warning

  • Minor

  • Major

  • Critical

If you choose a minimum severity level, the mail alerts are sent for that level and the other higher severity levels. For example, if you choose 'Minor' as the minimum severity level, you will receive email alerts for the minor, major, and critical fault events.

Step 5

In the SMTP Recipients area, do the following:

  1. Click the Add (+) button to add the email recipients to whom notifications should be sent. Enter the email ID and click Save.

    To delete an email recipient, select the email recipient and click the Delete (X) button.

  2. Click Send Test Mail to check whether the email recipient you added is reachable.

    If the email address and the SMTP settings are valid, a confirmation pop-up window appears with the message that an email has been sent. If the settings are not valid, a confirmation pop-up window appears with the message that no email has been sent. The Reachability column indicates whether test mails have been sent successfully to the email recipient. The Reachability column has one of the following values:

    • Yes (if the test mail has been sent successfully)

    • No (if the test mail has not been sent successfully)

    • na (if no test mail has been sent)

Step 6

Click Save Changes.

Troubleshooting

The following table describes troubleshooting suggestions for SMTP mail alert configuration issues (when the reachability status is No) that may appear in the Cisco IMC logs:

Issue

Suggested Solution

Timeout was reached

This could occur when you are not able to reach the configured SMTP IP address. Enter a valid IP address.

Couldn't resolve host name

This could occur when you are not able to reach the configured SMTP domain name. Enter a valid domain name.

Couldn't connect to server

This could occur when the SMTP IP or domain name or port number is/are incorrectly configured. Enter valid configuration details.

Failed sending data to the peer

This could occur when the an invalid recipient email ID is configured. Enter a valid email ID.

Adding SMTP Email Recipients

Add email recipients on the Mail Alert tab to receive email notifications for server faults.

Before you begin

Procedure

Step 1

In the Navigation pane, click the Admin menu.

Step 2

In the Admin menu, click Communication Services.

Step 3

In the Communications Services pane, click the Mail Alert tab.

Step 4

In the SMTP Recipients area, do the following:

  1. Click the Add (+) button to add the email recipients to whom notifications should be sent. Enter the email ID and click Save.

  2. Click Send Test Mail to check whether the email recipient you added is reachable.

    If the email address and the SMTP settings are valid, a confirmation pop-up window appears with the message that an email has been sent. If the settings are not valid, a confirmation pop-up window appears with the message that no email has been sent. The Reachability column indicates whether test mails have been sent successfully to the email recipient. The Reachability column has one of the following values:

    • Yes (if the test mail has been sent successfully)

    • No (if the test mail has not been sent successfully)

    • na (if no test mail has been sent)

Was this Document Helpful?

FeedbackFeedback

Contact Cisco