- Preface
- Overview
- Using the Command-Line Interface
- Configuring the Switch Alarms
- Assigning the Switch IP Address and Default Gateway
- Configuring Cisco IOS Configuration Engine
- Clustering Switches
- Configuring SDM Templates
- Administering the Switch
- Configuring Switch-Based Authentication
- Configuring IEEE 802.1x Port-Based Authentication
- Configuring Web-Based Authentication
- Configuring SGT Exchange Protocol over TCP (SXP) and Layer 3 Transport
- Configuring Interface Characteristics
- Configuring Smartports Macros
- Configuring VLANs
- Configuring VTP
- Configuring Voice VLAN
- Configuring Private VLANs
- Configuring IEEE 802.1Q and Layer 2 Protocol Tunneling
- Configuring STP
- Configuring MSTP
- Configuring Optional Spanning-Tree Features
- Configuring Resilient Ethernet Protocol
- Configuring Flex Links and the MAC Address-Table Move Update Feature
- Configuring DHCP Features and IP Source Guard
- Configuring Dynamic ARP Inspection
- Configuring Port-Based Traffic Control
- Configuring SPAN and RSPAN
- Configuring LLDP, LLDP-MED, and Wired Location Service
- Configuring CDP
- Configuring UDLD
- Configuring RMON
- Configuring System Message Logging
- Configuring SNMP
- Configuring Embedded Event Manager
- Configuring Network Security with ACLs
- Configuring QoS
- Configuring EtherChannels and Link-State Tracking
- Configuring IP Unicast Routing
- Configuring IPv6 Unicast Routing
- Implementing IPv6 Multicast
- Configuring IPv6 MLD Snooping
- Configuring IPv6 ACLs
- Configuring HSRP and VRRP
- Configuring Cisco IOS IP SLAs Operations
- Configuring Enhanced Object Tracking
- Configuring Web Cache Services By Using WCCP
- Configuring Fallback Bridging
- Troubleshooting
- Working with the Cisco IOS File System, Configuration Files, and Software Images
- Unsupported Commands in Cisco IOS Release 15.0(2)SE
- Index
- Access Control Lists
- Archive Commands
- ARP Commands
- Boot Loader Commands
- Embedded Syslog Manager
- Debug Commands
- High Availability
- IGMP Snooping Commands
- Interface Commands
- IP SLA
- MAC Address Commands
- Miscellaneous
- NetFlow Commands
- Network Address Translation (NAT) Commands
- QoS
- RADIUS
- SNMP
- SNMPv3
- Spanning Tree
- VLAN
Unsupported Commands in Cisco IOS Release 15.2(2)E
This appendix lists some of the command-line interface (CLI) commands that appear when you enter the question mark (?) at the IE 3010 switch prompt but are not supported in this release, either because they are not tested or because of switch hardware limitations. This is not a complete list. These unsupported commands are listed by software feature and command mode:
- Access Control Lists
- Archive Commands
- Boot Loader Commands
- Embedded Syslog Manager
- Debug Commands
- High Availability
- IGMP Snooping Commands
- Interface Commands
- IP SLA
- MAC Address Commands
- Miscellaneous
- NetFlow Commands
- Network Address Translation (NAT) Commands
- QoS
- RADIUS
- SNMP
- SNMPv3
- Spanning Tree
- VLAN
Access Control Lists
Unsupported Privileged EXEC Commands
access-enable [ host ] [ timeout minutes ]
access-template [ access-list-number | name ] [ dynamic-name ] [ source ] [ destination ] [ timeout minutes ]
clear access-template [ access-list-number | name ] [ dynamic-name ] [ source ] [ destination ].
show access-lists rate-limit [ destination ]
show ip accounting [ checkpoint ] [ output-packets | access violations ]
Unsupported Global Configuration Commands
access-list rate-limit acl-index { precedence | mask prec-mask }
Unsupported Route-Map Configuration Commands
match ip address prefix-list prefix-list-name [ prefix-list-name...]
Archive Commands
Unsupported Privileged EXEC Commands
ARP Commands
Unsupported Global Configuration Commands
arp ip-address hardware-address smds
Unsupported Interface Configuration Commands
Boot Loader Commands
Unsupported Global Configuration Commands
Embedded Syslog Manager
Unsupported Global Configuration Commands
Unsupported Privileged EXEC Commands
Debug Commands
Unsupported Privileged EXEC Commands
High Availability
Unsupported SSO-Aware HSRP Commands
IGMP Snooping Commands
Unsupported Global Configuration Commands
Interface Commands
Unsupported Privileged EXEC Commands
show interfaces [ interface-id | vlan vlan-id ] [ crb | fair-queue | irb | mac-accounting | precedence | irb | random-detect | rate-limit | shape ]
Unsupported Global Configuration Commands
Unsupported Interface Configuration Commands
IP SLA
Unsupported MPLS Health Monitor Commands
Unsupported Ethernet Gatekeeper Registration Commands
Unsupported VoIP Call Setup Probe Commands
MAC Address Commands
Unsupported Privileged EXEC Commands
show mac-address-table address
show mac-address-table aging-time
show mac-address-table dynamic
show mac-address-table interface
show mac-address-table multicast
show mac-address-table notification
show mac address-table multicast
Note
Use the show ip igmp snooping groups privileged EXEC command to display Layer 2 multicast address-table entries for a VLAN.
Unsupported Global Configuration Commands
Miscellaneous
Unsupported User EXEC Commands
Unsupported Privileged EXEC Commands
Unsupported Global Configuration Commands
errdisable recovery cause unicast flood
NetFlow Commands
Unsupported Global Configuration Commands
Network Address Translation (NAT) Commands
Unsupported Privileged EXEC Commands
QoS
Unsupported Global Configuration Command
Unsupported Interface Configuration Commands
Unsupported Policy-Map Configuration Command
class class-default where class-default is the class-map-name.
RADIUS
Unsupported Global Configuration Commands
aaa authentication feature default enable
aaa authentication feature default line
SNMP
Unsupported Global Configuration Commands
logging discriminator discr-name [[ facility ] [ mnemonics ] [ msg-body ] { drops string | includes string }] [ severity { drops sev-num | includes sev-num }] [ rate-limit msglimit ]
Feedback