Contents

Configuring Wi-Fi Direct Client Policy

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the Feature Information Table at the end of this document.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to http:/​/​www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Restrictions for the Wi-Fi Direct Client Policy

Wi-Fi Direct Client Policy is applicable to WLANs that have APs in local mode only.

Information About the Wi-Fi Direct Client Policy

Devices that are Wi-Fi Direct capable can connect directly to each other quickly and conveniently to do tasks such as printing, synchronization, and sharing of data. Wi-Fi Direct devices may associate with multiple peer-to-peer (P2P) devices and with infrastructure wireless LANs (WLANs) concurrently. You can use the switch to configure the Wi-Fi Direct Client Policy, on a per WLAN basis, where you can allow or disallow association of Wi-Fi devices with infrastructure WLANs, or disable Wi-Fi Direct Client Policy altogether for WLANs.

Related Tasks
Configuring the Wi-Fi Direct Client Policy (CLI)
Disabling Wi-Fi Direct Client Policy (CLI)
Related References
Monitoring Wi-Fi Direct Client Policy (CLI)

How to Configure Wi-Fi Direct Client Policy

Configuring the Wi-Fi Direct Client Policy (CLI)

SUMMARY STEPS

    1.    configure terminal

    2.    wlan profile-name

    3.    wifidirect policy {permit | deny }

    4.    end


DETAILED STEPS
     Command or ActionPurpose
    Step 1 configure terminal


    Example: 
    Switch# configure terminal
     

    Enters global configuration mode.

     
    Step 2wlan profile-name


    Example: 
    Switch# wlan test4
     

    Enters the WLAN configuration submode. The profile-name is the profile name of the configured WLAN.

     
    Step 3wifidirect policy {permit | deny }


    Example:
    Switch(config-wlan)# wifidirect policy permit
     
    Configures the Wi-Fi Direct client policy on the WLAN using one of the following:
    • permit—Enables Wi-Fi Direct clients to associate with the WLAN.
    • deny—When the Wi-Fi Direct policy is configured as "deny," the switch permits or denies Wi-Fi Direct devices based on the device capabilities. A Wi-Fi Direct device reports these capabilities in its association request to the switch and these are based on the Wi-Fi capabilities of the device. These include:
      • Concurrent operation
      • Cross connection
      Note   

      The command no wifidirect policy ignores the client's Wi-Fi direct status. Additionally, the access point also does not advertise any beacons and probes. Effectively, the no form of the command disables the Wi-Fi direct feature on the WLAN.

      If the Wi-Fi device supports either concurrent operations or cross connections or both, the client association is denied. The client can associate if the device does not support concurrent operations and cross connections.
     
    Step 4end


    Example:
    Switch(config-wlan)# end
     

    Returns to privileged EXEC mode. Alternatively, you can also press Ctrl-z to exit global configuration mode.

     
    Related Concepts
    Information About the Wi-Fi Direct Client Policy
    Related References
    Monitoring Wi-Fi Direct Client Policy (CLI)

    Disabling Wi-Fi Direct Client Policy (CLI)

    SUMMARY STEPS

      1.    configure terminal

      2.    wlan profile-name

      3.    no wifidirect policy

      4.    end


    DETAILED STEPS
       Command or ActionPurpose
      Step 1 configure terminal


      Example: 
      Switch# configure terminal
       

      Enters global configuration mode.

       
      Step 2wlan profile-name


      Example: 
      Switch# wlan test4
       

      Enters the WLAN configuration submode. The profile-name is the profile name of the configured WLAN.

       
      Step 3no wifidirect policy


      Example:
      Switch(config)# no wifidirect policy
       

      Ignores the Wi-Fi Direct status of clients thereby allowing Wi-Fi Direct clients to associate.

       
      Step 4end


      Example:
      Switch(config-wlan)# end
       

      Returns to privileged EXEC mode. Alternatively, you can also press Ctrl-z to exit global configuration mode.

       
      Related Concepts
      Information About the Wi-Fi Direct Client Policy
      Related References
      Monitoring Wi-Fi Direct Client Policy (CLI)

      Monitoring Wi-Fi Direct Client Policy (CLI)

      The following commands can be used to monitor Wi-Fi Direct Client Policy:

      Command Description
      show wireless client wifidirect stats

      Displays the total number of clients associated and the number of association requests rejected if the Wi-Fi Direct Client Policy is enabled.
      show wlan summary

      Displays status of the Wi-Fi Direct on the WLAN.
      show wireless cli mac-address mac-address

      Displays the detail information of a client.
      Related Concepts
      Information About the Wi-Fi Direct Client Policy
      Related Tasks
      Configuring the Wi-Fi Direct Client Policy (CLI)
      Disabling Wi-Fi Direct Client Policy (CLI)

      Additional References for Wi-Fi Direct Client Policy

      Related Documents

      Related Topic Document Title

      WLAN Command reference

      		 WLAN Command Reference, Cisco IOS XE Release 3SE (Catalyst 3850 Switches)

      Error Message Decoder

      Description Link

      To help you research and resolve system error messages in this release, use the Error Message Decoder tool.

      https:/​/​www.cisco.com/​cgi-bin/​Support/​Errordecoder/​index.cgi

      MIBs

      MIB MIBs Link

      All Supported MIBs for this release.

      To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

      http:/​/​www.cisco.com/​go/​mibs

      Technical Assistance

      Description Link

      The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

      To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

      Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

      http:/​/​www.cisco.com/​support

      Feature Information about Wi-Fi Direct Client Policy

      Feature Name Release Feature Information
      Wi-Fi Direct Feature Cisco IOS XE 3.3SE This feature was introduced.
      Configuring Wi-Fi Direct Client Policy

      Configuring Wi-Fi Direct Client Policy

      Finding Feature Information

      Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the Feature Information Table at the end of this document.

      Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to http:/​/​www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

      Restrictions for the Wi-Fi Direct Client Policy

      Wi-Fi Direct Client Policy is applicable to WLANs that have APs in local mode only.

      Information About the Wi-Fi Direct Client Policy

      Devices that are Wi-Fi Direct capable can connect directly to each other quickly and conveniently to do tasks such as printing, synchronization, and sharing of data. Wi-Fi Direct devices may associate with multiple peer-to-peer (P2P) devices and with infrastructure wireless LANs (WLANs) concurrently. You can use the switch to configure the Wi-Fi Direct Client Policy, on a per WLAN basis, where you can allow or disallow association of Wi-Fi devices with infrastructure WLANs, or disable Wi-Fi Direct Client Policy altogether for WLANs.

      Related Tasks
      Related References

      How to Configure Wi-Fi Direct Client Policy

      Configuring the Wi-Fi Direct Client Policy (CLI)

      SUMMARY STEPS

        1.    configure terminal

        2.    wlan profile-name

        3.    wifidirect policy {permit | deny }

        4.    end


      DETAILED STEPS
         Command or ActionPurpose
        Step 1 configure terminal


        Example: 
        Switch# configure terminal
         

        Enters global configuration mode.

         
        Step 2wlan profile-name


        Example: 
        Switch# wlan test4
         

        Enters the WLAN configuration submode. The profile-name is the profile name of the configured WLAN.

         
        Step 3wifidirect policy {permit | deny }


        Example:
        Switch(config-wlan)# wifidirect policy permit
         
        Configures the Wi-Fi Direct client policy on the WLAN using one of the following:
        • permit—Enables Wi-Fi Direct clients to associate with the WLAN.
        • deny—When the Wi-Fi Direct policy is configured as "deny," the switch permits or denies Wi-Fi Direct devices based on the device capabilities. A Wi-Fi Direct device reports these capabilities in its association request to the switch and these are based on the Wi-Fi capabilities of the device. These include:
          • Concurrent operation
          • Cross connection
          Note   

          The command no wifidirect policy ignores the client's Wi-Fi direct status. Additionally, the access point also does not advertise any beacons and probes. Effectively, the no form of the command disables the Wi-Fi direct feature on the WLAN.

          If the Wi-Fi device supports either concurrent operations or cross connections or both, the client association is denied. The client can associate if the device does not support concurrent operations and cross connections.
         
        Step 4end


        Example:
        Switch(config-wlan)# end
         

        Returns to privileged EXEC mode. Alternatively, you can also press Ctrl-z to exit global configuration mode.

         
        Related Concepts
        Related References

        Disabling Wi-Fi Direct Client Policy (CLI)

        SUMMARY STEPS

          1.    configure terminal

          2.    wlan profile-name

          3.    no wifidirect policy

          4.    end


        DETAILED STEPS
           Command or ActionPurpose
          Step 1 configure terminal


          Example: 
          Switch# configure terminal
           

          Enters global configuration mode.

           
          Step 2wlan profile-name


          Example: 
          Switch# wlan test4
           

          Enters the WLAN configuration submode. The profile-name is the profile name of the configured WLAN.

           
          Step 3no wifidirect policy


          Example:
          Switch(config)# no wifidirect policy
           

          Ignores the Wi-Fi Direct status of clients thereby allowing Wi-Fi Direct clients to associate.

           
          Step 4end


          Example:
          Switch(config-wlan)# end
           

          Returns to privileged EXEC mode. Alternatively, you can also press Ctrl-z to exit global configuration mode.

           
          Related Concepts
          Related References

          Monitoring Wi-Fi Direct Client Policy (CLI)

          The following commands can be used to monitor Wi-Fi Direct Client Policy:

          Command Description
          show wireless client wifidirect stats

          Displays the total number of clients associated and the number of association requests rejected if the Wi-Fi Direct Client Policy is enabled.
          show wlan summary

          Displays status of the Wi-Fi Direct on the WLAN.
          show wireless cli mac-address mac-address

          Displays the detail information of a client.
          Related Concepts
          Related Tasks

          Additional References for Wi-Fi Direct Client Policy

          Related Documents

          Related Topic Document Title

          WLAN Command reference

          		 WLAN Command Reference, Cisco IOS XE Release 3SE (Catalyst 3850 Switches)

          Error Message Decoder

          Description Link

          To help you research and resolve system error messages in this release, use the Error Message Decoder tool.

          https:/​/​www.cisco.com/​cgi-bin/​Support/​Errordecoder/​index.cgi

          MIBs

          MIB MIBs Link

          All Supported MIBs for this release.

          To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

          http:/​/​www.cisco.com/​go/​mibs

          Technical Assistance

          Description Link

          The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

          To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

          Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

          http:/​/​www.cisco.com/​support

          Feature Information about Wi-Fi Direct Client Policy

          Feature Name Release Feature Information
          Wi-Fi Direct Feature Cisco IOS XE 3.3SE This feature was introduced.