Unsupported Commands in Cisco IOS Release 12.2(53)SE1

This appendix lists some of the command-line interface (CLI) commands that appear when you enter the question mark (?) at the Catalyst 2960 or 2960-S switch prompt but are not supported in this release, either because they are not tested or because of switch hardware limitations. This is not a complete list. These unsupported commands are listed by software feature and command mode:

Access Control Lists

Unsupported Privileged EXEC Commands

access-enable [ host ] [ timeout minutes ]

access-template [ access-list-number | name ] [ dynamic-name ] [ source ] [ destination ] [ timeout minutes ]

clear access-template [ access-list-number | name ] [ dynamic-name ] [ source ] [ destination ].

show access-lists rate-limit [ destination ]

show accounting

show ip accounting [ checkpoint ] [ output-packets | access violations ]

show ip cache [ prefix-mask ] [ type number ]

Unsupported Global Configuration Commands

access-list rate-limit acl-index { precedence | mask prec-mask }

access-list dynamic extended

Unsupported Route-Map Configuration Commands

match ip address prefix-list prefix-list-name [ prefix-list-name...]

Boot Loader Commands

Unsupported Global Configuration Commands

boot buffersize

Debug Commands

Unsupported Privileged EXEC Commands

debug platform cli-redirection main

debug platform configuration

IGMP Snooping Commands

Unsupported Global Configuration Commands

ip igmp snooping tcn

Interface Commands

Unsupported Privileged EXEC Commands

show interfaces [ interface-id | vlan vlan-id ] [ crb | fair-queue | irb | mac-accounting | precedence | irb | random-detect | rate-limit | shape ]

Unsupported Global Configuration Commands

interface tunnel

Unsupported Interface Configuration Commands

transmit-interface type number

MAC Address Commands

Unsupported Privileged EXEC Commands

show mac-address-table

show mac-address-table address

show mac-address-table aging-time

show mac-address-table count

show mac-address-table dynamic

show mac-address-table interface

show mac-address-table multicast

show mac-address-table notification

show mac-address-table static

show mac-address-table vlan

show mac address-table multicast

Note Use the show ip igmp snooping groups privileged EXEC command to display Layer 2 multicast address-table entries for a VLAN.

Unsupported Global Configuration Commands

mac-address-table aging-time

mac-address-table notification

mac-address-table static

Miscellaneous

Unsupported User EXEC Commands

verify

Unsupported Privileged EXEC Commands

file verify auto

show cable-diagnostics prbs

test cable-diagnostics prbs

Unsupported Global Configuration Commands

errdisable recovery cause unicast flood

l2protocol-tunnel global drop-threshold

memory reserve critical

service compress-config

stack-mac persistent timer

Network Address Translation (NAT) Commands

Unsupported Privileged EXEC Commands

show ip nat statistics

show ip nat translations

QoS

Unsupported Global Configuration Command

priority-list

Unsupported Interface Configuration Commands

priority-group

rate-limit

Unsupported Policy-Map Configuration Command

class class-default where class-default is the class-map-name.

RADIUS

Unsupported Global Configuration Commands

aaa nas port extended

aaa authentication feature default enable

aaa authentication feature default line

aaa nas port extended

authentication command bounce-port ignore (only on switches running the LAN Lite image)

authentication command disable-port ignore (only on switches running the LAN Lite image)

radius-server attribute nas-port

radius-server configure

radius-server extended-portnames

SNMP

Unsupported Global Configuration Commands

no monitor session all (only on switches running the LAN Lite image)

snmp-server enable informs

snmp-server enable traps hsrp

snmp-server enable traps rtr (only on switches running the LAN Lite image)

snmp-server ifindex persist

SNMPv3

Unsupported 3DES Encryption Commands

All

Spanning Tree

Unsupported Global Configuration Command

spanning-tree pathcost method { long | short }

Unsupported Interface Configuration Command

spanning-tree stack-port

VLAN

Unsupported Global Configuration Command

vlan internal allocation policy { ascending | descending }

Unsupported vlan-config Command

private-vlan

Unsupported User EXEC Commands

show running-config vlan

show vlan ifindex

vlan database

Unsupported vlan-config Command

private-vlan

Unsupported VLAN Database Commands

vtp

vlan

show vlan private-vlan

VTP

Unsupported Privileged EXEC Commands

vtp { password password | pruning | version number }

Note This command has been replaced by the vtp global configuration command.