O Commands

oam-channel

{ oam-channel <val> } | { no oam-channel }

Syntax Description

Syntax Description

oam-channel

oam-channel used

val

2 - nvo3 tissa
Command Mode
  • /exec/configure/configngoamprofile

obfl logging uuid msg

obfl logging uuid <uuid> <log-file> msg <log_str>

Syntax Description

Syntax Description

obfl

Perform the OBFL operation

logging

Perform the logging

uuid

UUID of the process

uuid

UUID of the process

log-file

Log File of your process

msg

Message to be Logged in the file

log_str

Type the message to be logged
Command Mode
  • /exec

object-group ip address

[no] object-group ip address <name>

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

object-group

Configure ACL object groups

ip

IP Object groups

address

Address object group

name

object-group name
Command Mode
  • /exec/configure

object-group ip port

[no] object-group ip port <name>

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

object-group

Configure ACL object groups

ip

IP Object groups

port

IP port object group (can be used in IPv4 and IPv6 access-lists)

name

object-group name
Command Mode
  • /exec/configure

object-group ipv6 address

[no] object-group ipv6 address <name>

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

object-group

Configure ACL object groups

ipv6

IPv6 Object groups

address

Address object group

name

object-group name
Command Mode
  • /exec/configure

of-port interface

[no] of-port interface <ifname>

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

of-port

Add interfaces to openflow switch

interface

Interface

ifname

interface name
Command Mode
  • /exec/configure/openflow/switch

offset-list route in

[no] offset-list { { route-map <map> } | { prefix-list <list> } } { in | out } <offset> <interface>

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

offset-list

Add or subtract offset from EIGRP metrics

route-map

Use a route-map for offset-list selection

map

Route-map name

prefix-list

Use a prefix-list for offset-list selection

list

Reference to prefix-list name

in

Perform offset on incoming updates

out

Perform offset on outgoing updates

offset

Offset

interface

Interface name
Command Mode
  • /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

onep

[no] onep

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

onep

Enable/Disable One Platform
Command Mode
  • /exec/configure

onep applications

[no] onep applications <config-domain>

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

onep

One Platform

applications

One platform applications

config-domain

Virtual service name or tag used by remote onep applications to retrieve its configuration
Command Mode
  • /exec/configure

onep install

onep install <xsd-location> <config-domain>

Syntax Description

Syntax Description

onep

One Platform

install

install a CLI definition

xsd-location

the xsd file containing the onep application CLI definition

config-domain

virtual service name or tag used by remote onep applications to retrieve its configuration
Command Mode
  • /exec

onep stop

onep stop { session { all | <onep-session-id> } }

Syntax Description

Syntax Description

onep

One Platform

stop

Stop specific activity

session

One Platform session

all

All sessions

onep-session-id

Specific session name
Command Mode
  • /exec

onep uninstall

onep uninstall <app-name> <app-version> <config-domain> [ force ]

Syntax Description

Syntax Description

onep

One Platform

uninstall

uninstall a CLI definition

app-name

application name

app-version

application version

config-domain

virtual service name or tag used by remote onep applications to retrieve its configuration

force

(Optional) force uninstallation
Command Mode
  • /exec

open-fsm

[no] open-fsm

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

open-fsm

Enable session open FSM for establishing BGP sessions
Command Mode
  • /exec/configure/router-bgp

openflow

[no] openflow

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

openflow

OpenFlow configuration
Command Mode
  • /exec/configure

operation-packet-priority normal

{ { no | default } operation-packet-priority | operation-packet-priority { normal | high } }

Syntax Description

Syntax Description

no

default

Set a command to its defaults

operation-packet-priority

Set operation packet properties

high

Priority high

normal

Priority normal
Command Mode
  • /exec/configure/ip-sla/jitter

option exporter-stats timeout

{ [ no ] option exporter-stats timeout <time> | no option exporter-stats timeout }

Syntax Description

Syntax Description

option

Version 9 Option Templates and Data

exporter-stats

Exporter Statistics Option

timeout

Option resend time

time

Time in seconds
Command Mode
  • /exec/configure/nfm-exporter-v9

option interface-table timeout

{ [ no ] option interface-table timeout <time> | no option interface-table timeout }

Syntax Description

Syntax Description

option

Version 9 Option Templates and Data

interface-table

Interface Table Option

timeout

Option resend time

time

Time in seconds
Command Mode
  • /exec/configure/nfm-exporter-v9

option sampler-table timeout

{ [ no ] option sampler-table timeout <time> | no option sampler-table timeout }

Syntax Description

Syntax Description

option

Version 9 Option Templates and Data

sampler-table

Export Sampler Information

timeout

Option resend time

time

Time in seconds
Command Mode
  • /exec/configure/nfm-exporter-v9

orib event-history

[no] orib event-history { cli | ipc | uroute | mroute | mroute_only | uhw | mhw | ha | internal } { size { <size_in_text> | <size_in_kbytes> } }

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

orib

Display ORIB information

event-history

ORIB event logs

cli

ORIB cli logs

ipc

ORIB ipc logs

uroute

ORIB unicast route logs

mroute

ORIB multicast route logs

mroute_only

ORIB multicast route logs without mhw

uhw

ORIB unicast platform logs

mhw

ORIB multicast platform logs

ha

ORIB ha logs

internal

ORIB internal logs

size

Configure size

size_in_text

Buffer size

size_in_kbytes

Size in kbytes
Command Mode
  • /exec/configure

orib orib_api_init

{ orib orib_api_init <client-name> } | { orib orib_api_close } | { orib orib_add_route <client-name> <mac> [ <nh> | <nh6> ] <if-name> } | { orib orib_delete_route <client-name> <mac> [ <nh> | <nh6> ] <if-name> }

Syntax Description

Syntax Description

orib

Use ORIB API routines from OTV process

orib_api_init

Call orib_api_init() from the OTV process

orib_api_close

Call orib_api_close() from the OTV process

orib_add_route

Call orib_add_route() from OTV process

orib_delete_route

Call orib_delete_route() from OTV process

client-name

Client name registered to ORIB process

mac

VLAN-ID/MAC Address tuple in vvvv-aaaa.bbbb.cccc format

nh

(Optional) Next-hop IPv4 address

if-name

Next-hop interface (iod)
Command Mode
  • /exec

ospfv3 authentication

ospfv3 authentication { disable | ipsec spi <spi_id> { md5 <akey> | sha1 <akey> } } | no ospfv3 authentication { disable | ipsec spi <spi_id> }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

ospfv3

OSPFv3 configuration commands

authentication

Enable Authentication

disable

Disable Authentication

ipsec

IPSec

spi

Security Parameter Index

spi_id

SPI Value

md5

Use the MD5 algorithim

akey

Authentication Key

sha1

Use the SHA1 algorithim

akey

Authentication Key
Command Mode
  • /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel /exec/configure/if-mgmt-config

ospfv3 bfd

[no] ospfv3 bfd [ disable ]

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

ospfv3

OSPFv3 configuration commands

bfd

Enable BFD on this interface

disable

(Optional) Disable BFD on this interface
Command Mode
  • /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mgmt-config

ospfv3 cost

{ ospfv3 cost <cost> } | { no ospfv3 cost [ <cost> ] }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

ospfv3

OSPFv3 configuration commands

cost

Cost associated with interface

cost

Cost value
Command Mode
  • /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel /exec/configure/if-mgmt-config

ospfv3 dead-interval

{ ospfv3 dead-interval <interval> } | { no ospfv3 dead-interval [ <interval> ] }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

ospfv3

OSPFv3 configuration commands

dead-interval

Dead interval

interval

(seconds)
Command Mode
  • /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel /exec/configure/if-mgmt-config

ospfv3 event-history detail

[no] ospfv3 event-history detail

Syntax Description

Syntax Description

no

Negate a command or set its defaults

ospfv3

Debugging functions

event-history

log debug events into event history buffer

detail

Detailed event history buffer
Command Mode
  • /exec/configure/router-ospf3

ospfv3 flood-bw-percentage

[no] ospfv3 flood-bw-percentage <percentage>

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

ospfv3

OSPFv3 configuration commands

flood-bw-percentage

Percentage of bandwidth used for flooding

percentage

Negate a command or set its defaults
Command Mode
  • /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel /exec/configure/if-mgmt-config

ospfv3 hello-interval

{ ospfv3 hello-interval <interval> } | { no ospfv3 hello-interval [ <interval> ] }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

ospfv3

OSPFv3 configuration commands

hello-interval

Hello interval

interval

(seconds)
Command Mode
  • /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel /exec/configure/if-mgmt-config

ospfv3 instance

{ ospfv3 instance <instance-id> } | { no ospfv3 instance [ <instance-id> ] }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

ospfv3

OSPFv3 configuration commands

instance

Instance identifier

instance-id

Instance identifier value
Command Mode
  • /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel /exec/configure/if-mgmt-config

ospfv3 mtu-ignore

[no] ospfv3 mtu-ignore

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

ospfv3

OSPFv3 configuration commands

mtu-ignore

Disable OSPF MTU mismatch detection
Command Mode
  • /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel /exec/configure/if-mgmt-config

ospfv3 network broadcast

{ ospfv3 network { broadcast | point-to-point } } | { no ospfv3 network [ { broadcast | point-to-point } ] }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

ospfv3

OSPFv3 configuration commands

network

Network type

broadcast

Specify OSPF broadcast multi-access network

point-to-point

Specify OSPF point-to-point network
Command Mode
  • /exec/configure/if-broadcast /exec/configure/if-p2p /exec/configure/if-mgmt-config

ospfv3 network point-to-point

{ ospfv3 network point-to-point } | { no ospfv3 network [ point-to-point ] }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

ospfv3

OSPFv3 configuration commands

network

Network type

point-to-point

Specify OSPF point-to-point network
Command Mode
  • /exec/configure/if-loopback

ospfv3 passive-interface

[ default | no ] ospfv3 passive-interface

Syntax Description

Syntax Description

default

(Optional) Undo a command

no

(Optional) Negate a command or set its defaults

ospfv3

OSPFv3 configuration commands

passive-interface

Suppress routing updates on the interface
Command Mode
  • /exec/configure/if-broadcast /exec/configure/if-p2p /exec/configure/if-mgmt-config

ospfv3 priority

{ ospfv3 priority <prio> } | { no ospfv3 priority [ <prio> ] }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

ospfv3

OSPFv3 configuration commands

priority

Router priority

prio

Router priority
Command Mode
  • /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel /exec/configure/if-mgmt-config

ospfv3 retransmit-interval

{ ospfv3 retransmit-interval <interval> } | { no ospfv3 retransmit-interval [ <interval> ] }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

ospfv3

OSPFv3 configuration commands

retransmit-interval

Packet retransmission interval

interval

(seconds)
Command Mode
  • /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel /exec/configure/if-mgmt-config

ospfv3 shutdown

[no] ospfv3 shutdown

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

ospfv3

OSPFv3 configuration commands

shutdown

Shutdown ospf on this interface
Command Mode
  • /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mgmt-config

ospfv3 transmit-delay

{ ospfv3 transmit-delay <delay> } | { no ospfv3 transmit-delay [ <delay> ] }

Syntax Description

Syntax Description

no

Negate a command or set its defaults

ospfv3

OSPFv3 configuration commands

transmit-delay

Packet transmission delay

delay

(seconds)
Command Mode
  • /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel /exec/configure/if-mgmt-config

overbudgetshut

overbudgetshut [ module <module> ]

Syntax Description

Syntax Description

overbudgetshut

Shut down the specified LCs due to power over budget

module

(Optional) Module Force Shut down

module

(Optional) please enter the module number
Command Mode
  • /exec

overbudgetsyslog

overbudgetsyslog

Syntax Description

Syntax Description

overbudgetsyslog

Print Syslog to indicate power over budget
Command Mode
  • /exec

overlay-encapsulation

[no] overlay-encapsulation <encap-type> [ tunnel-control-frames [ <layer2-prot> ] ]

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

overlay-encapsulation

NVE Overlay Encapsulation

encap-type

Configure encapsulation type

tunnel-control-frames

(Optional) tunnel protocol

layer2-prot

(Optional) configure specific protocol
Command Mode
  • /exec/configure/if-nve

overlay-encapsulation

[no] overlay-encapsulation <encap-type> [ tunnel-control-frames ]

Syntax Description

Syntax Description

no

(Optional) Negate a command or set its defaults

overlay-encapsulation

NVE Overlay Encapsulation

encap-type

Configure encapsulation type

tunnel-control-frames

(Optional) tunnel protocol
Command Mode
  • /exec/configure/if-nve

overload rip

overload rip

Syntax Description

Syntax Description

overload

rip

Forced RIP overload
Command Mode
  • /exec

owner

{ { no | default } owner | owner <text> }

Syntax Description

Syntax Description

no

default

Set a command to its defaults

owner

Owner of Entry

text

Owner String
Command Mode
  • /exec/configure/ip-sla/udp /exec/configure/ip-sla/jitter /exec/configure/ip-sla/tcp /exec/configure/ip-sla/icmpEcho /exec/configure/ip-sla/dns /exec/configure/ip-sla/fabricPathEcho /exec/configure/ip-sla/http