Show Commands
This chapter describes the Cisco NX-OS Hot Standby Router Protocol (HSRP) show commands.
show hsrp
To display Hot Standby Router Protocol (HSRP) information for each HSRP group, use the show hsrp command.
show hsrp [interface {ethernet slot/port | port-channel number | vlan vlan-id}] [group group-number] [active | init | listen | standby] [all] [brief] [detail] [ipv4]
Syntax Description
Command Default
None
Command Modes
Command HistoryAny command mode
|
|
|
|---|---|
5.0(3)N1(1) |
This command was introduced. |
Usage Guidelines
Use the show hsrp command to display information about HSRP groups. The brief keyword displays a single line of information about each virtual gateway or virtual forwarder.
If you have not configured authentication, the show hsrp command will display the following string:
Authentication text "cisco"
This is the default behavior of HSRP as defined in RFC 2281:
If no authentication data is configured, the RECOMMENDED default
value is 0x63 0x69 0x73 0x63 0x6F 0x00 0x00 0x00.
This command does not require a license.
Note 
Make sure the LAN Base Services license is installed on the switch to enable Layer 3 interfaces.
Examples
This example shows how to display the default information about HSRP:
switch# show hsrp
Vlan1 - Group 1 (HSRP-V1) (IPv4)
Local state is Active, priority 150 (Cfged 150), may preempt
Forwarding threshold(for vPC), lower: 1 upper: 150
Preemption Delay (Seconds) Reload:300
Hellotime 3 sec, holdtime 10 sec
Next hello sent in 0.793000 sec(s)
Virtual IP address is 10.1.1.3 (Cfged)
Active router is local
Standby router is unknown
Authentication text "cisco"
Virtual mac address is 0000.0c07.ac01 (Default MAC)
17 state changes, last state change 1w0d
IP redundancy name is hsrp-Vlan1-1 (default)
...
Note The authentication text string in the preceding example indicates that authentication has not been configured on the interface.
This example shows how to display a brief summary of HSRP information:
switch# show hsrp brief
P indicates configured to preempt.
|
Interface Grp Prio P State Active addr Standby addr Group addr
Vlan1 1 150 P Active local unknown 10.1.1.3 (conf)
Vlan2 2 150 P Active local unknown 10.1.2.3 (conf)
...
Related Commands
|
|
|
|---|---|
feature hsrp |
Enables the HSRP feature. |
show hsrp delay
To display the Hot Standby Router Protocol (HSRP) group delay information, use the show hsrp delay command.
show hsrp delay [interface {ethernet slot/port | port-channel number[.sub_if_number] | vlan vlan_id}] [group group-number] [all] [brief]
Syntax Description
Command Default
None
Command Modes
Command HistoryAny command mode
|
|
|
|---|---|
5.0(3)N1(1) |
This command was introduced. |
Usage Guidelines
This command does not require a license.
Note Make sure the LAN Base Services license is installed on the switch to enable Layer 3 interfaces.
Examples
This example shows how to display HSRP delay information:
switch# show hsrp delay
---------------------------------
Interface Minimum Reload
---------------------------------
Eth1/5 30 0
switch#
Related Commands
|
|
|
|---|---|
delay minimum |
Configures the delay infromation for HSRP groups. |
feature hsrp |
Enables the HSRP feature. |
hsrp delay |
Configures the delay infromation for HSRP groups. |
show hsrp summary
To display Hot Standby Router Protocol (HSRP) summary information for each HSRP group, use the show hsrp summary command.
show hsrp summary
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Command HistoryAny command mode
|
|
|
|---|---|
5.0(3)N1(1) |
This command was introduced. |
Usage Guidelines
This command does not require a license.
Note Make sure the LAN Base Services license is installed on the switch to enable Layer 3 interfaces.
Examples
This example shows how to display a summary of HSRP information:
switch# show hsrp summary
HSRP Summary:
Extended-hold (NSF) disabled
Global HSRP-BFD disabled
Total Groups: 1
Version:: V1-IPV4: 1 V2-IPV4: 0 V2-IPV6: 0
State:: Active: 0 Standby: 0 Listen: 0
State:: V6-Active: 0 V6-Standby: 0 V6-Listen: 0
Total HSRP Enabled interfaces: 1
Total Packets:
Tx - Pass: 0 Fail: 0
Rx - Good: 0
Packet for unknown groups: 0
Total MTS: Rx: 25
switch#
Related Commands
|
|
|
|---|---|
feature hsrp |
Enables the HSRP feature. |
hsrp |
Configures HSRP groups. |
Feedback