- About This Guide
- Chapter 1, ACT Commands
- Chapter 2, ALW Commands
- Chapter 3, APPLY Commands
- Chapter 4, CANC Commands
- Chapter 5, CHG Commands
- Chapter 6, CLR Commands
- Chapter 7, CONN Commands
- Chapter 8, COPY Commands
- Chapter 9, DISC Commands
- Chapter 10, DLT Commands
- Chapter 11, ED Commands
- Chapter 12, ENT Commands
- Chapter 13, EX Commands
- Chapter 14, INH Commands
- Chapter 15, INIT Commands
- Chapter 16, OPR Commands
- Chapter 17, REPT Messages
- Chapter 18, RLS Commands
- Chapter 19, RMV Commands
- Chapter 20, RST Commands
- Chapter 21, RTRV Commands
- Chapter 22, SCHED Commands
- Chapter 23, SET Commands
- Chapter 24, SW Commands
- Chapter 25, Access Identifiers
- Chapter 26, Conditions
- Chapter 27, Modifiers
SET Commands
This chapter provides SET (set) commands for the Cisco ONS 15454, ONS 15327, ONS 15600 and ONS 15310-CL.
23.1 SET-ALMTH-<MOD2>
Set Alarm Threshold (10GFC, 10GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, CLNT, D1VIDEO, DS1, DV6000, E1, E3, E4, EC1, ESCON, ETRCLO, FSTE, G1000, GFPOS, GIGE, HDTV, ISC1, OC12, OC192, OC3, OC48, OCH, OMS, OTS, POS, STS1, STS12C, STS18C, STS192C, STS24C, STS36C, STS3C, STS48C, STS6C, STS9C, T1, T3, VC12, VC3, VT1, VT2)
Usage Guidelines
Cisco ONS 15454, ONS 15327, ONS 15310-CL
This command sets the alarm thresholds on the following cards/ports/channels: MXP_2.5G_10G/TXP_MR_10G, optical service channel, optical amplifier, dispersion compensation units, multiplex/demultiplex and OADM.
The only applicable MOD2 values are CLNT/OCH/OMS/OTS.
Category
DWDM
Security
Provisioning
Related Commands
Input Format
SET-ALMTH-<MOD2>:[<TID>]:<AID>:<CTAG>::<CONDTYPE>,<THLEV>[,,,];
Input Example
SET-ALMTH-{MOD2}::FAC-1-1:1::OPT-LOW,10;
Input Parameters
|
|
|
|---|---|
AID |
Access identifier from the "25.1.1 ALL" section on page 25-1. Must not be null |
CONDTYPE |
Condition type for an alarm or a reported event Parameter type is ALM_THR—alarm threshold list for MXP_2.5G_10G, TXP_MR_10G, OSCM, OSC-CSM, OPT-PRE, OPT-BST, MD-4, MUX-32, DMX-32, AD-1C, AD-2C, AD-4C, AD-1B, and AD-4B cards |
• |
Battery Voltage - Extremely High |
• |
Battery Voltage - Extremely Low |
• |
Battery Voltage - High |
• |
Battery Voltage - Low |
• |
Gain not reached—High Degrade Threshold |
• |
Gain not reached—High Failure Threshold |
• |
Gain not reached—Low Degrade Threshold |
• |
Gain not reached—Low Failure Threshold |
• |
Laser Bias current in uA as 1/10% High Warning Threshold, Low Warning Threshold Measured value [0.0%, 100.0%] |
• |
Receive power in 1/10 uW Measured value [-40.0 dBm,+30.0 dBm] |
• |
Receive power in 1/10 uW Measured value [-40.0 dBm,+30.0 dBm |
• |
Transmit power in 1/10 uW. Measured value [-40.0 dBm,+30.0 dBm] |
• |
Transmit power in 1/10 uW. Measured value [-40.0 dBm,+30.0 dBm] |
• |
Optical Power—High Degrade Threshold |
• |
Optical Power—High Failure Threshold |
• |
Optical Power—Low Degrade Threshold |
• |
Optical Power—Low Failure Threshold |
• |
VOA Attenuation—High Degrade Threshold |
• |
VOA Attenuation—High Failure Threshold |
• |
VOA Attenuation—Low Degrade Threshold |
• |
VOA Attenuation—Low Failure Threshold |
THLEVEL |
Threshold level. Float |
23.2 SET-ALMTH-EQPT
Set Alarm Threshold Equipment
Usage Guidelines
Cisco ONS 15454, ONS 15310-CL
This command sets the alarm thresholds to manage the power level monitoring on an NE.
Category
Equipment
Security
Provisioning
Related Commands
Input Format
SET-ALMTH-EQPT:[<TID>]::<CTAG>::<ALMTHTYPE>,<THLEV>[,,,];
Input Example
SET-ALMTH-EQPT:::1::BATV-HIGH,-53.5;
Input Parameters
23.3 SET-ATTR-CONT
Set Attribute Control
Usage Guidelines
Cisco ONS 15454, ONS 15327, ONS 15600, ONS 15310-CL
This command sets the attributes associated with an external control. The attributes are used when an external control is operated or released. To send the attributes, use the RTRV-ATTR-CONT command.
Note 
If the <CONTTYPE> parameter is not specified, the control specified by <AID> is unprovisioned.
Note A control should be unprovisioned before it is reprovisioned to another type of control.
Category
Environment
Security
Provisioning
Related Commands
OPR-ACO-ALL OPR-EXT-CONT REPT ALM ENV REPT EVT ENV |
RLS-EXT-CONT RTRV-ALM-ENV RTRV-ATTR-CONT RTRV-ATTR-ENV |
RTRV-COND-ENV RTRV-EXT-CONT SET-ATTR-ENV SET-ATTR-SECUDFLT |
Input Format
SET-ATTR-CONT:[<TID>]:<AID>:<CTAG>[::<CONTTYPE>];
Input Example
SET-ATTR-CONT:CISCO:ENV-OUT-1:123::AIRCOND;
Input Parameters
|
|
|
|---|---|
AID |
Access identifier from the "25.1.12 ENV" section on page 25-26. Identifies the external control for which attributes are being retrieved |
CONTTYPE |
Environmental control type. A null value is equivalent to ALL Parameter type is CONTTYPE—Environmental control types |
• |
Air conditioning |
• |
Engine |
• |
Fan |
• |
Generator |
• |
Heat |
• |
Light |
• |
Miscellaneous |
• |
Sprinkler |
23.4 SET-ATTR-ENV
Set Attribute Environment
Usage Guidelines
Cisco ONS 15454, ONS 15327, ONS 15600, ONS 15310-CL
This command sets the attributes associated with an external control.
Note•If the <NTFCNCDE>, <ALMTYPE>, and <ALMMSG> parameters are omitted, the environmental alarm specified by <AID> is unprovisioned.
•An alarm should be unprovisioned and you should wait for any raised alarm to clear before reprovisioning the alarm to another alarm type.
•CL in NOTIF_CODE is not valid for provisioning commands. It is only valid for autonomous messages.
Category
Environment
Security
Provisioning
Related Commands
OPR-ACO-ALL OPR-EXT-CONT REPT ALM ENV REPT EVT ENV |
RLS-EXT-CONT RTRV-ALM-ENV RTRV-ATTR-CONT RTRV-ATTR-ENV |
RTRV-COND-ENV RTRV-EXT-CONT SET-ATTR-CONT SET-ATTR-SECUDFLT |
Input Format
SET-ATTR-ENV:[<TID>]:<AID>:<CTAG>::[<NTFCNCDE>],[<ALMTYPE>],[<ALMMSG>];
Input Example
SET-ATTR-ENV:CISCO:ENV-IN-1:123::MJ,OPENDR,\"OPEN DOOR\";
Input Parameters
|
|
|
|---|---|
AID |
Access identifier from the "25.1.12 ENV" section on page 25-26. Must not be null |
NTFCNCDE |
Two-letter notification code. Must not be null Parameter type is NOTIF_CODE—two-character notification code associated with an autonomous message |
• |
The condition causing the alarm has cleared |
• |
A critical alarm |
• |
A major alarm |
• |
A minor alarm |
• |
The condition is not alarmed |
• |
The alarm is not reported |
ALMTYPE |
The alarm type for the environmental alarm. Must not be null Parameter type is ENV_ALM—environmental alarm types |
• |
Air compressor failure |
• |
Air conditioning failure |
• |
Air dryer failure |
• |
Battery discharging |
• |
Battery failure |
• |
Cooling fan failure |
• |
Centralized power major failure |
• |
Centralized power minor failure |
• |
Engine failure |
• |
Engine operating |
• |
Standby engine transfer |
• |
Explosive gas |
• |
Fire detector failure |
• |
Fire |
• |
Flood |
• |
Fuel leak |
• |
Fuse failure |
• |
Explosive gas, toxic gas, ventilation fail or gas monitor fail |
• |
CEV hatch fail |
• |
Generator failure |
• |
High airflow |
• |
High humidity |
• |
High temperature |
• |
High water |
• |
Intrusion |
• |
Level converter |
• |
Secondary ADSL low voltage disconnect |
• |
Low voltage disconnected bypass |
• |
Low battery voltage |
• |
Low fuel |
• |
Low humidity |
• |
Low cable pressure |
• |
Low temperature |
• |
Low water |
• |
Miscellaneous |
• |
Open door |
• |
Commercial power failure |
• |
Pump failure |
• |
48V power supply failure |
• |
-139V power converter |
• |
-190V power converter |
• |
Power supply major |
• |
Power supply minor |
• |
Rectifier failure |
• |
Rectifier high voltage |
• |
Rectifier low voltage |
• |
Ringing generator major |
• |
Ringing generator minor |
• |
AC or AC/rectifier power fail ADSL equipment |
• |
AC or AC/rectifier power fail DCL equipment critical site |
• |
AC or AC/rectifier power fail DCL equipment |
• |
Commercial AC fail, site equipped with standby engine |
• |
AC power loss distributed power RT bay |
• |
Retrieve standby engine, commercial AC restored |
• |
Smoke |
• |
High-low temperature |
• |
Toxic gas |
• |
T-repeater shelf |
• |
Ventilation system failure |
ALMMSG |
Alarm message. String. Must not be null |
23.5 SET-ATTR-SECUDFLT
Set Attribute Security Default
Usage Guidelines
Cisco ONS 15454, ONS 15327, ONS 15600, ONS 15310-CL
This command sets the system-wide default values associated with several security parameters.
The following parameters are set on a system-wide basis for all users and all privilege levels: MXINV, DURAL, UOUT, PFRCD, POLD, PINT, and LOGIN. The PRIVLVL keyword cannot be used to set these parameters for a specific privilege level.
The following parameters are set on a privilege-level basis: PAGE, PCND, and TMOUT. If any of these values are specified, the PRIVLVL keyword must also be present. If none of these parameters are specified, the PRIVLVL keyword cannot be used.
Note Password aging can only be enabled/disabled for all privilege levels. The PRIVLVL keyword cannot be used with PAGE=0 to disable a specific user privilege level.
When system-level and privilege-level keywords are combined in the same command, system-level parameters are still set for all privilege levels, regardless of the value specified by PRIVLVL. Privilege-level parameters are only set for the privilege level specified by PRIVLVL.
Note If PAGE and PINT both have values greater than 0, PINT must be less than PAGE.
The order of keywords is not restricted. Commas are only needed to separate keywords. If no keywords are specified, all parameters are left as is.
Category
Security
Security
Superuser
Related Commands
Input Format
SET-ATTR-SECUDFLT:[<TID>]::<CTAG>::[PAGE=<PAGE>],[PCND=<PCND>],
[MXINV=<MXINV>],[DURAL=<DURAL>],[TMOUT=<TMOUT>],[UOUT=<UOUT>],
[PFRCD=<PFRCD>],[POLD=<POLD>],[PINT=<PINT>],[LOGIN=<LOGIN>],
[PRIVLVL=<PRIVLVL>],[PDIF=<PDIF>];
Input Example
SET-ATTR-SECUDFLT:CISCO::123::PAGE=45,PCND=5,MXINV=5,DURAL=30,
TMOUT=0,UOUT=20,PFRCD=NO,POLD=5,PINT=20,LOGIN=MULTIPLE,
PRIVLVL=RTRV,PDIF=1;
Input Parameters
23.6 SET-PMMODE-<STS_PATH>
Set Performance Mode of PM Data Collection (STS1, STS12C, STS18C, STS192C, STS24C, STS36C, STS3C, STS48C, STS6C, STS9C)
Usage Guidelines
Cisco ONS 15454
This command sets the mode and turns the PM data collection mode on or off.
See Table 27-1 on page 27-1 for supported modifiers by platform.
Note•The PM mode and state of an entity are retrieved by using the RTRV-PMMODE command.
•The near end monitoring of the intermediate-path PM (IPPM) only supports OC3, OC12, OC48, OC192, and EC-1 on STS Path.
•The far end IPPM data collection is supported by the MRC-12 card only.
•This release of software will support only the Path (P) mode type PM parameters with this command, that is, this command is not applicable for Line (L) and Section (S) mode types. The PM monitoring for Line (L) and Section (S) are supported by the ONS 15454, and the storing PM data is always performed.
Category
Performance
Security
Provisioning
Related Commands
Input Format
SET-PMMODE-<STS_PATH>:[<TID>]:<SRC>:<CTAG>::<LOCN>,<MODETYPE>,
[<PMSTATE>];
Input Example
SET-PMMODE-STS1:CISCO:STS-4-1-2:123::NEND,P,ON;
Input Parameters
|
|
|
|---|---|
SRC |
Source access identifier from the "25.1.9 CrossConnectId" section on page 25-15 |
LOCN |
Location associated with a particular command. Identifies the location from which the PM mode is to be retrieved. Only the near end PM data collection is supported Parameter type is LOCATION—the location where the action is to take place |
• |
Action occurs on the Near End of the facility |
MODETYPE |
The type of PM parameters that the entity or the sub entity is to store as a result of an attribute change. Only the path (P) PM parameter is supported Parameter type is PM_MODE—the type of PM parameters |
• |
Transport Path PM parameters |
PMSTATE |
Directs the named PM mode type to turn on or off. A null value defaults to on Parameter type is PM_STATE—directs the named PM mode type - path (P) state |
• |
Disable the mode |
• |
Enable the mode |
23.7 SET-TH-<MOD2>
Set Threshold (10GFC, 10GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, CLNT, D1VIDEO, DS1, DS3I, DV6000, E1, E3, E4, EC1, ESCON, ETRCLO, FSTE, G1000, GFPOS, GIGE, HDTV, ISC1, OC12, OC192, OC3, OC48, OCH, OMS, OTS, POS, STM1E, STS1, STS12C, STS18C, STS192C, STS24C, STS36C, STS3C, STS48C, STS6C, STS9C, T1, T3, VC11, VC12, VC3, VT1, VT2)
Usage Guidelines
Cisco ONS 15454, ONS 15327, ONS 15600, ONS 15310-CL
This command sets the threshold for PM and sets the alarm thresholds for the MXP_2.5G_10G/TXP_MR_10G cards. If this command is used to set the alarm thresholds, the time-period is not applicable.
See Table 27-1 on page 27-1 for supported modifiers by platform.
The rules are as follows: The PM Thresholds have a default of NEND for the location. The Alarm Thresholds do not require or interpret the location. The TMPER is not applicable to alarm thresholds. The TMPER default is 15-MIN. The client ports only accept SONET, Laser and alarm MONTYPES. The trunk ports accept SONET, Laser, alarm, FEC, OTN and 8B10B MONTYPES.
Refer to the Cisco ONS SONET TL1 Reference Guide for specific card provisioning rules.
Category
Performance
Security
Provisioning
Related Commands
Input Format
SET-TH-<MOD2>:[<TID>]:<AID>:<CTAG>::<MONTYPE>,<THLEV>,[<LOCN>],,[<TMPER>];
Input Example
SET-TH-T3:CISCO:FAC-1-1:123::CVL,12,NEND,,15-MIN;
Input Parameters
|
|
|
|---|---|
AID |
Access identifier from the "25.1.1 ALL" section on page 25-1. All the STS, VT1, Facility, and DS1 AIDs are supported |
MONTYPE |
Monitored type Parameter type is ALL_MONTYPE—monitoring type list |
• |
Alarm Indication Signal Seconds—Path |
• |
All possible values |
• |
OTN—Background Block Errors—Path Monitor Point |
• |
OTN—Background Block Errors—Section Monitor Point |
• |
OTN—Background Block Error Ratio—Path Monitor Point expressed as 1/10th of a percentage. |
• |
OTN—Background Block Error Ratio—Section Monitor Point expressed as 1/10th of a percentage. |
• |
FEC—Bit Errors Corrected |
• |
8B10B—Code Group Violations |
• |
Controlled Slip Seconds—Path (DSXM-12 FDL/T1.403 PM count) |
• |
Coding Violations—CP-Bit Path |
• |
Coding Violations—Line |
• |
Coding Violations—Path |
• |
Coding Violations—Section |
• |
Coding Violations—Section |
• |
8B10B—Data Code Groups |
• |
Errored Second Type A-Path (DS3XM-12 DS1 PM count) |
• |
Errored Second Type B-Path (DS3XM-12 DS1 PM count) |
• |
Errored Seconds—CP—Bit Path |
• |
Errored Seconds—Line |
• |
Errored Second—Network Path (DS3XM-12 DS1 PM count) |
• |
Errored Seconds—Path |
• |
OTN—Errored Seconds—Path Monitor Point |
• |
OTN—Errored Seconds—Section Monitor Point |
• |
Errored Second—Ratio |
• |
Errored Seconds Ratio—Path monitor Point expressed as 1/10th of a percentage |
• |
Errored Seconds Ratio—Section monitor Point expressed as 1/10th of a percentage |
• |
Errored Seconds—Section |
• |
Errored Seconds—VT Path |
• |
The total number of good packets received that were directed to a multicast address |
• |
Number of transmit packets that are collisions |
• |
The total number of packets received that have a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets |
• |
Number of received frames dropped at the port level |
• |
The total number of packets received that were less than 64 octets |
• |
The total number of packets received that are longer than 1518 octets |
• |
The total number of octets of data |
• |
The total number of packets received that are longer than 1518 octets |
• |
The total number of packets (including bad packets, broadcast packets, and multicast packets) received |
• |
The total number of packets received that are less than 64 octets |
• |
Failure Count—Line |
• |
Failure Count—Path |
• |
OTN—Failure Count—Path Monitor Point |
• |
OTN—Failure Count—Section Monitor Point |
• |
Availability Ratio |
• |
High-Order Path Background Block Error |
• |
High-Order Path Background Block Error Ratio |
• |
High-Order Path Errored Block |
• |
High-Order Path Errored Second |
• |
High-Order Path Errored Seconds - A |
• |
High-Order Path Errored Seconds - B |
• |
High-Order Path Errored Second Ratio |
• |
High-Order Path Failure Count |
• |
High-Order Path Negative Pointer Justification Count |
• |
High-Order Path, Negative Pointer Justification Count |
• |
Outage Intensity |
• |
High-Order Path Pointer Justification Count Difference |
• |
High-Order Path Pointer Justification Count |
• |
High-Order Path Pointer Justification Count Seconds |
• |
High-Order Path Positive Pointer Justification Count |
• |
High-Order Path, Positive Pointer Justification Count |
• |
The number of SEP events in available time |
• |
High-Order Path Severely Errored Seconds |
• |
High-Order Path Severely Errored Second Ratio |
• |
High-Order Path Unavailable Seconds |
• |
Number of broadcast packets received since the last counter reset |
• |
The number of inbound packets |
• |
Receive Error Byte |
• |
The number of inbound packets (or transmission units) that contained errors |
• |
Receive Framing Error |
• |
Receive Interpkt Junk |
• |
Number of multicast packets received since the last counter reset |
• |
Number of bytes transmitted since the last counter reset |
• |
Number of unicast packets received since the last counter reset |
• |
Number of broadcast packets transmitted |
• |
The number of outbound packets |
• |
The number of outbound packets (or transmission units) that could not be transmitted because of errors |
• |
Number of multicast packets transmitted |
• |
Received payload CRC errors |
• |
Number of unicast packets transmitted |
• |
8B10B- Idle Ordered Sets |
• |
Invalid Packet Count |
• |
Average Laser Bias current in uA |
• |
Maximum Laser Bias current in uA |
• |
Minimum Laser Bias current in uA |
• |
Normalized Laser Bias Current for OC3-8 |
• |
Laser Bias Current |
• |
Laser Bias Current |
• |
Loss of Signal Seconds—Line |
• |
Low-Order Path Background Block Error |
• |
Low-Order Path Background Block Error Ratio |
• |
Low-Order Path Errored Block |
• |
Low-Order Path Errored Second |
• |
Low-Order Path Errored Seconds-A |
• |
Low-Order Path Errored Seconds-B |
• |
Low-Order Path Errored Second Ratio |
• |
Low-Order Path Failure Count |
• |
Low-Order Negative Pointer Justification Count, Detected |
• |
Low Order Negative Pointer Justification Count, Generated |
• |
Low-Order Positive Pointer Justification Count, Detected |
• |
Low-Order positive Pointer Justification Count, Generated |
• |
Low-Order Path Severely Errored Period |
• |
Low-Order Path Severely Errored Period Intensity |
• |
Low-Order Path Severely Errored |
• |
Low-Order Path Unavailable Seconds |
• |
Protection switch count |
• |
Protection switch duration |
• |
8B10B—Non Idle Ordered Sets |
• |
PPJC-PDET:Negative Pointer Justification |
• |
PPJC-PGEN:Negative Pointer Justification |
• |
Average Receive Power in 1/10 uW |
• |
Maximum Receive Power in 1/10 uW |
• |
Minimum Receive Power in 1/10 uW |
• |
Normalized Optical Receive Power for OC3-8 |
• |
Maximum value for OPRN |
• |
Minimum value for OPRN |
• |
Average Transmit Power in 1/10 uW |
• |
Maximum Transmit Power in 1/10 uW |
• |
Minimum Transmit Power in 1/10uW |
• |
Normalized value for Optical Power Transmitted for the OC3-8 card |
• |
Maximum value for OPTN |
• |
Minimum value for OPTN |
• |
Optical Power—Average Interval Value in 1/10th of dBm |
• |
Optical Power—Maximum Interval Value in 1/10th of dBm |
• |
Optical Power—Minimum Interval Value in 1/10th of dBm |
• |
PPJC-PDET:Positive Pointer Justification |
• |
PPJC-PGEN:Positive Pointer Justification |
• |
Protection Switching Count |
• |
Protection Switching Count—Ring |
• |
Protection Switching Count—Span |
• |
Protection Switching Count—Working |
• |
Protection Switching Duration |
• |
Protection Switching Duration—Ring |
• |
Protection Switching Duration—Span |
• |
Protection Switching Duration—Working |
• |
Severely Errored Framing/AIS Second—CP-Bit Path |
• |
Severely Errored Framing/AIS Seconds Path |
• |
Severely Errored Framing Seconds |
• |
Severely Errored Framing Seconds—Path (DS3XM-12 DS1 PM count) |
• |
Severely Errored Second—CP-Bit Path |
• |
Severely Errored Second—Line |
• |
Severely Errored Second—Network Path (DS3XM-12 DS1 PM count) |
• |
Severely Errored Second—Path |
• |
OTN—Severely Errored Second—Path |
• |
OTN—Severely Errored Second Ratio—Path Monitor Point expressed as 1/10th of a percentage |
• |
OTN—Severely Errored Second Ratio—Section Monitor Point expressed as 1/10th of a percentage |
• |
Severely Errored Second—Section |
• |
OTN—Severely Errored Second—Section Monitor Point |
• |
Severely Errored Second—VT Path |
• |
Unavailable Second—CP-Bit Path |
• |
Unavailable Second—Line |
• |
Unavailable Second—Network Path (DS3XM-12 DS1 PM count) |
• |
Unavailable Second—Path |
• |
OTN—Unavailable Second—Path Monitor Point |
• |
OTN—Unavailable Second—Section Monitor Point |
• |
Unavailable Second—VT Path |
• |
FEC—Uncorrectable Words |
• |
Valid Packet Count |
THELV |
Threshold level. Float |
LOCN |
Location associated with a particular command Parameter type is LOCATION—the location where the action is to take place |
• |
Action occurs on the Far End of the facility |
• |
Action occurs on the Near End of the facility |
TMPER |
Accumulation time period for performance counters. Optional Parameter type is TMPER—accumulation time period for the performance management center |
• |
Performance parameter accumulation interval length; every 24-hours. For SONET PM data only one day of history data is available. For RMON managed PM data seven days of history data are available. |
• |
Performance parameter accumulation interval length; every 1 hour. This is only applicable to RMON managed PM data. There are 24 hours of history data available. |
• |
Performance parameter accumulation interval length; every 1 minute. This is only applicable to RMON managed PM data. There are 60 minutes of history available. |
• |
Performance parameter accumulation interval length; every 15 minutes. There are 32 15-MIN buckets of history data available for this accumulation interval length. |
• |
Performance parameter accumulation interval length; starting from the last time the counters were cleared. This is only applicable to RMON managed PMs. |
23.8 SET-TOD
Set Time of Day
Usage Guidelines
Cisco ONS 15454, ONS 15327, ONS 15600, ONS 15310-CL
This command sets the system date and time for the NE. The year should be entered using four digits while the hour should be entered using a 24-hour time period (for example, military time).
Category
System
Security
Provisioning
Related Commands
Input Format
SET-TOD:[<TID>]::<CTAG>::<YEAR>,<MONTH>,<DAY>,<HOUR>,<MINUTE>,<SECOND>,
[<DIFFERENCE>][:DST=<DST>];
Input Example
SET-TOD:CAZADERO::240::1998,05,08,13,18,55,480:DST=Y;
Feedback