RST Commands
This chapter provides RST (restore) commands for the Cisco ONS 15454, ONS 15327, ONS 15600 and ONS 15310-CL.
20.1 RST-<MOD2>
Restore (10GFC, 10GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, CLNT, D1VIDEO, DS1, DV6000, E1, E3, E4, EC1, ESCON, ETRCLO, FSTE, G1000, GFPOS, GIGE, HDTV, ISC1, OC12, OC192, OC3, OC48, OCH, OMS, OTS, POS, STS1, STS12C, STS18C, STS192C, STS24C, STS36C, STS3C, STS48C, STS6C, STS9C, T1, T3, VC12, VC3, VT1, VT2)
Usage Guidelines
Cisco ONS 15454, ONS 15327, ONS 15600, ONS 15310-CL
This command provisions a facility in service.
See Table 27-1 on page 27-1 for supported modifiers by platform.
Note This command can only be executed when the port is in OOS,MT state.
Category
Facility
Security
Maintenance
Related Commands
DLT-<MOD1PAYLOAD> DLT-FFP-<MOD2DWDMPAYLOAD> DLT-FFP-<OCN_TYPE> ED-<GIGE_TYPE> ED-<MOD1FCPAYLOAD> ED-<MOD1FICONPAYLOAD> ED-<MOD2DWDMPAYLOAD> ED-<OCN_TYPE> ED-ALS ED-DS1 ED-EC1 ED-FFP-<MOD2DWDMPAYLOAD> ED-FFP-<OCN_TYPE> ED-FSTE ED-G1000 ED-GFP ED-HDLC ED-POS ED-T1 ED-T3 ED-TRC-<MOD2DWDMPAYLOAD> ED-TRC-<OCN_TYPE> ENT-<MOD1PAYLOAD> ENT-FFP-<MOD2DWDMPAYLOAD> ENT-FFP-<OCN_TYPE> INIT-REG-<MOD2> OPR-ALS OPR-LPBK-<MOD2> OPR-PROTNSW-<MOD2DWDMPAYLOAD> OPR-PROTNSW-<OCN_TYPE> REPT PM <MOD2> RLS-PROTNSW-<MOD2DWDMPAYLOAD> |
RLS-PROTNSW-<OCN_TYPE> RMV-<MOD2> RTRV-<MOD1FCPAYLOAD> RTRV-<MOD1FICONPAYLOAD> RTRV-<MOD2DWDMPAYLOAD> RTRV-<OCN_TYPE> RTRV-10GIGE RTRV-ALMTH-<MOD2> RTRV-ALS RTRV-DS1 RTRV-EC1RTRV-FAC RTRV-FFP-<MOD2DWDMPAYLOAD> RTRV-FFP-<OCN_TYPE> RTRV-FSTE RTRV-G1000 RTRV-GFP RTRV-GIGE RTRV-HDLC RTRV-PM-<MOD2> RTRV-PMSCHED-<MOD2> RTRV-POS RTRV-PROTNSW-<MOD2DWDMPAYLOAD> RTRV-PROTNSW-<OCN_TYPE> RTRV-T1 RTRV-T3 RTRV-TH-<MOD2> RTRV-TRC-<MOD2DWDMPAYLOAD> RTRV-TRC-<OCN_TYPE> SCHED-PMREPT-<MOD2> SET-ALMTH-<MOD2> SET-TH-<MOD2> |
Input Format
RST-<MOD2>:[<TID>]:<AID>:<CTAG>::::[<PST>[,<sst>]];
Input Example
RST-EC1:CISCO:FAC-1-1:1::::IS,AINS;
Input Parameters
Table 20-1 RST-<MOD2> Input Parameters
|
|
AID |
Access identifier from the "25.1.1 ALL" section on page 25-1 |
PST |
Primary state. Defaults to IS Parameter type is PST—indicates the current overall service condition of an entity |
•IS |
In service |
•OOS |
Out of service |
SST |
Secondary state. Defaults to AINS Parameter type is SST—provides additional information pertaining to PST and PSTQ |
•AINS |
Automatic in service |
•DSBLD |
Disabled |
•LPBK |
Loopback |
•MEA |
Mismatch of equipment and attributes |
•MT |
Maintenance mode |
•OOG |
Out of group |
•SWDL |
Software downloading |
•UAS |
Unassigned |
•UEQ |
Unequipped |
20.2 RST-EQPT
Restore Equipment
Usage Guidelines
Cisco ONS 15454, ONS 15327, ONS 15600, ONS 15310-CL
This command provisions equipment into the IS state from the MT state.
Note Only applicable to equipment that is in transition from the MT state to the IS state.
Category
Equipment
Security
Maintenance
Related Commands
ALW-SWDX-EQPT ALW-SWTOPROTN-EQPT ALW-SWTOWKG-EQPT CHG-EQPT DLT-EQPT ED-EQPT ENT-EQPT INH-SWDX-EQPT INH-SWTOPROTN-EQPT INH-SWTOWKG-EQPT REPT ALM EQPT REPT EVT EQPT |
REPT RMV EQPT REPT RST EQPT RMV-EQPT RTRV-ALM-EQPT RTRV-ALMTH-EQPT RTRV-COND-EQPT RTRV-EQPT SET-ALMTH-EQPT SW-DX-EQPT SW-TOPROTN-EQPT SW-TOWKG-EQPT |
Input Format
RST-EQPT:[<TID>]:<AID>:<CTAG>[::];
Input Example
RST-EQPT:CISCO:SLOT-1:1;
Input Parameters