Order Information

Sales order number:

Estimated shipping date:

Site ready date:

Installation date:

Site Location and Address

Company name:

Site address:

Shipping address:

Building or computer room access:

Special instructions:

Hours and days of operation:

Site Survey Contacts

Primary Contact

Name:

Title:

Phone number:

Mobile phone number:

Fax number:

Pager number:

E-mail address:

Secondary Contact

Name:

Title:

Phone number:

Mobile phone number:

Fax number:

Pager number:

E-mail address:

Delivery and Installation Constraints

Is there a loading dock available to unload the equipment at this site?

Is the path to the installation area unobstructed? If not, can special arrangements be made to get the equipment to the installation area? Describe them.

On what floor is the installation?

If it is on a floor other than the ground floor, is there a freight elevator available? Note if the equipment will have to be brought up a flight of stairs.

Is there someone on site during working hours to accept delivery of the materials? If not, list the times this person would be available.

For more information, see Shipping and Receiving.

Floor Mounting

How many Cisco CRS 16-Slot Line Card Chassis Enhanced routers will be installed? Is there floor space available for all of the chassis?

Does the floor meet the routing system floor-loading requirements?

Can the primary or secondary chassis mounting locations be used to secure the chassis to the floor, or will an outrigger kit be required?

Make a sketch of the area where the chassis is to be installed and note the chassis location.

For more information, see Space Planning.

Power

Is AC or DC power available for the chassis? Is there a connection point on the panel for the chassis?

Is there a fuse access panel (FAP) available for the equipment? Provide a connection point on the fuse access panel for each chassis.

Will a fuse access panel be installed in time for the routing system installation? Provide a date when the FAP will be installed.

Is the FAP in the same room as the chassis?

Is there an AC power outlet (220 V or 110 V) located within 10 feet of each chassis for PCs and test equipment?

Is there proper grounding for the equipment? If not, when will the grounding be available? Provide a connection point for the grounding.

Are there any restrictions when the equipment can be powered on or when electrical work can be done? If so, describe them.

Are there special requirements for power or power cables (for example, a different wire gauge, and so on)? If so, describe them.

For more information, see Power and Cooling Requirements.

Air Conditioning

Does the site have the air conditioning capacity to handle the routing system? If not, note what will be done to rectify the lack of adequate cooling.

Describe the air conditioning at the site.

For more information, see Power and Cooling Requirements.

System Interconnection Cabling (if applicable)

Has the chassis-to-chassis interconnection cabling been considered?

Control Plane, BITS, and Alarm Interfaces

Will the facility building integrated timing source (BITS) be used? Has the cabling been considered?

Will the chassis be connected to an external alarm system? Has the cabling been considered?

Supported Data Interfaces

Will the routing system be connected to OC-3/STM-1 POS circuits? How many ports?

Will the routing system be connected to OC-48/STM-16 POS or DPT circuits? How many ports?

Will the routing system be connected to OC-192/STM-64 POS or RPR XFP circuits? How many ports?

Will the routing system be connected to OC-768/STM-256 POS circuits? How many ports?

Will the routing system be connected to Gigabit Ethernet (GE) or 10-GE circuits? How many ports?

Will the routing system be connected to 100-GE circuits? How many ports?

Cable Plant

Are there connection points on the fiber distribution panel for all optical cables connecting to the routing system?

Will fiber jumpers be provided? If not, measure and record the length of fiber jumper required to complete the installation, and place the order.

What type of fiber connector is used at the site?

If attenuation is required, will attenuators be provided? If not, who will provide the attenuators?