Routing Policy Language Commands on Cisco IOS XR Software
This chapter describes the Cisco IOS XR software routing policy language (RPL) commands used to create, modify, monitor, and maintain routing policies.
For detailed information about RPL concepts, configuration tasks, and examples, see Implementing Routing Policy on Cisco IOS XR Software module in Cisco IOS XR Routing Configuration Guide.
abort (RPL)
To discard a route policy or set definition and return to global configuration mode, use the abort command in the appropriate configuration mode.
abort
Syntax Description
This command has no arguments or keywords.
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Prefix set configuration
Route distinguisher set configuration
AS path set configuration
Community set configuration
Extended community set configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following example shows how to discard a route policy definition that was started and return to global configuration mode:
RP/0/RP0/CPU0:router(config)# route-policy policy_1
RP/0/RP0/CPU0:router(config-rpl)# if as-path is-local then
RP/0/RP0/CPU0:router(config-rpl-if)# abort
RP/0/RP0/CPU0:router(config)#
The following example shows how to discard a prefix set definition that was started and return to global configuration mode:
RP/0/RP0/CPU0:router(config)# prefix-set legal-ipv4-prefix-examples
RP/0/RP0/CPU0:router(config-pfx)# 10.0.1.1,
RP/0/RP0/CPU0:router(config-pfx)# 10.0.2.0/24,
RP/0/RP0/CPU0:router(config-pfx)# abort
RP/0/RP0/CPU0:router(config)#
add
To add a value to an Routing Information Protocol (RIP) or Enhanced Interior Gateway Protocol (EIGRP) existing metric, use the add command in route-policy configuration mode.
add {eigrp-metric bandwidth delay reliability loading max-transmission | rip-metric {number | parameter}}
Syntax Description
eigrp-metric |
Specifies an EIGRP metric attribute. |
bandwidth |
Bandwidth in kilobits per second. Range is from 0 to 4294967295. |
delay |
Delay in 10-microsecond units. Range is from 0 to 4294967295. |
reliability |
Reliability metric. 255 is 100-percent reliable. Range is from 0 to 255. |
loading |
Effective bandwidth (loading). 255 is 100-percent loaded. Range is from 0 to 255. |
max-transmission |
Maximum transmission of the path. Range is from 0 to 65535. |
rip-metric |
Specifies an RIP metric attribute. |
number |
Value assigned to a four-bit unsigned integer. Range is from 0 to 16. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
If the add value is greater than the maximum allowed value, the metric is added. If the resulting metric exceeds the maximum for the routing protocol, then the route is dropped (by the client routing protocol).
Examples
The following example shows how to offset the RIP metric value:
RP/0/RP0/CPU0:router(config)# route-policy policy_1
RP/0/RP0/CPU0:router(config-rpl)# add rip-metric 4
RP/0/RP0/CPU0:router(config-rpl)# end-policy
The following example shows how to set the EIGRP metric value:
RP/0/RP0/CPU0:router(config)# route-policy policy_1
RP/0/RP0/CPU0:router(config-rpl)# add eigrp-metric 50000 24000 230 14000
RP/0/RP0/CPU0:router(config-rpl)# end-policy
apply
To execute a parameterized or unparameterized policy from within another policy, use the apply command in route-policy configuration mode.
apply policy_name [argument1, argument2, . . . , argumentN]
Syntax Description
policy_name |
Name of a route policy. |
argument |
(Optional) Parameter name. The argument can be a value (for example, '100' ) or a parameter (for example, '$parameter') |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the apply command to execute a policy (either parameterized or unparameterized) from within another policy, which allows for the reuse of common blocks of policy.
Examples
In the following example, the policy CustomerIn applies the route-policy SetLocalPref to conditionally set the local preference on a route. The parameters 20, 30, 40, and 50 are passed to the parameterized policy SetLocalPref, where the local preference is set to:
•20, if the community 217:20 is present in the route
•30, if the community 217:30 is present in the route
•40, if the community 217:40 is present in the route
•50, if the community 217:50 is present in the route
RP/0/RP0/CPU0:router(config)# route-policy SetLocalPref ($lp0, $lp1, $lp2, $lp3, $lp4)
RP/0/RP0/CPU0:router(config-rpl)# if community matches-any ($lp0:$lp1)then
RP/0/RP0/CPU0:router(config-rpl-elseif)# set local-preference $lp1
RP/0/RP0/CPU0:router(config-rpl-elseif)# elseif community matches-any ($lp0:$lp2) then
RP/0/RP0/CPU0:router(config-rpl-elseif)# set local-preference $lp2
RP/0/RP0/CPU0:router(config-rpl-elseif)# elseif community matches-any ($lp0:$lp3) then
RP/0/RP0/CPU0:router(config-rpl-elseif)# set local-preference $lp3
RP/0/RP0/CPU0:router(config-rpl-elseif)# elseif community matches-any ($lp0:$lp4) then
RP/0/RP0/CPU0:router(config-rpl-elseif)# set local-preference $lp4
RP/0/RP0/CPU0:router(config-rpl-elseif)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
RP/0/RP0/CPU0:router(config)# route-policy CustomerIn($cust)
RP/0/RP0/CPU0:router(config-rpl)# apply SetLocalPref ($cust, 20, 30, 40, 50)
RP/0/RP0/CPU0:router(config-rpl)# end-policy
RP/0/RP0/CPU0:router(config)# route-policy Cust_217
RP/0/RP0/CPU0:router(config-rpl)# apply CustomerIn(217)
RP/0/RP0/CPU0:router(config-rpl)# end-policy
as-path in
To match the AS path of a route to an AS path set, use the as-path in command in route-policy configuration mode.
as-path in {as-path-set-name | inline-as-path-set | parameter}
Syntax Description
as-path-set-name |
Name of an AS path set. |
inline-as-path-set |
Inline AS path set. The inline AS path set must be enclosed in parentheses. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
The parameter argument was added. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the as-path in command as a conditional expression within an if statement to match the AS path of a route to an AS path set. The AS path is a sequence of autonomous system numbers traversed by a route.
Note For a list of all conditional expressions available within an if statement, see the if command.
The as-path in command evaluates to true if at least one of the regular expressions defined in the associated AS path set matches the AS path attribute of the route.
In the case where the AS path set is defined but contains no elements in it, the as-path in conditional expression command returns false.
Examples
For example, assume we have an AS path set named my-as-set defined as follows:
RP/0/RP0/CPU0:router(config)# as-path-set my-as-set
RP/0/RP0/CPU0:router(config-as)# ios-regex '_12$',
RP/0/RP0/CPU0:router(config-as)# ios-regex '_13$'
RP/0/RP0/CPU0:router(config-as)# end-set
and the following policy excerpt using an as-path-set-name argument:
RP/0/RP0/CPU0:router(config-rpl)# if as-path in my-as-set then
RP/0/RP0/CPU0:router(config-rpl-if)# set local-preference 100
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)#
The AS path in condition evaluates to true if one or more of the regular expression matches in the set my-as-set match the AS path associated with the route. In the case of a defined but empty AS path set, this operator returns false.
The preceding policy excerpt is equivalent to the following version, which uses an inline-as-path set variable:
RP/0/RP0/CPU0:router(config-rpl)# if as-path in (ios-regex `_12$,ios-regex `_13$') then
RP/0/RP0/CPU0:router(config-rpl-if)# set local-preference 100
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)#
as-path is-local
To determine if this router or another router within this autonomous system or confederation originated a Border Gateway Protocol (BGP) route, use the as-path is-local command in route-policy configuration mode.
as-path is-local
Syntax Description
This command has no arguments or keywords.
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the as-path is-local command as a conditional expression within an if statement to determine if this router (or another router within this autonomous system or confederation) originated the route.
Note For a list of all conditional expressions available within an if statement, see the if command.
Routes that are locally originated within the autonomous system or confederation carry an empty AS path. For the Border Gateway Protocol (BGP) specification, when a route is advertised across the autonomous system boundary or a confederation boundary, the local autonomous system number or confederation ID is appended to the autonomous system path. The AS path of a locally originated aggregate is also empty unless it has been modified by policy.
The is-local operator evaluates to true for autonomous system paths that are empty. An empty AS path is how an AS path that is local to our autonomous system is represented in BGP.
Examples
In the following example, if the AS path is local, then the local preference is set to 100:
RP/0/RP0/CPU0:router(config-rpl)# if as-path is-local then
RP/0/RP0/CPU0:router(config-rpl-if)# set local-preference 100
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)#
as-path length
To compare the number of ASN in the AS path of a Border Gateway Protocol (BGP) route, use the as-path length command in route-policy configuration mode.
as-path length {eq | is | ge | le} {number | parameter}
Syntax Description
eq | is | ge | le |
Equal to; greater than or equal to; less than or equal to. |
number |
Value assigned to an 11-bit unsigned integer. Range is from 0 to 2047. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the as-path length command as a conditional expression within an if statement to perform a conditional check based on the length of the AS path.
Note For a list of all conditional expressions available within an if statement, see the if command.
This command takes either a specific integer value or a range of integer values specified with the ge and le operators. Any or all these integers can be parameterized. The operator counts one for each autonomous system in the path. In the case where the route may be aggregated and contain one or more AS sets, the length operator adds one for each set present, the occurrence of an AS set typically indicates that this route is an aggregated route, and the aggregated route had a component route that contained one of the autonomous systems in the set. Likewise, in the case of confederations, a count of one is added for each confederation in the path or each confederation set in the path. A null AS path has a length of zero.
Examples
In the following example, if the AS path length equals 10, then the local preference is set to 100:
RP/0/RP0/CPU0:router(config-rpl)# if as-path length eq 10 then
RP/0/RP0/CPU0:router(config-rpl-if)# set local-preference 100
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)#
Related Commands
|
|
as-path in |
Matches the AS path of a route to an AS path set. |
as-path originates-from |
Compares an AS path against the AS sequence beginning with the AS number that originated a route |
as-path passes-through |
Verifies if the supplied integer or parameter appears anywhere in the AS path or if the supplied sequence of integers and parameters appears, in the same order, anywhere in the AS path. |
as-path unique-length |
Performs specific checks based on the length of the AS path. |
as-path neighbor-is
To test autonomous system numbers at the head of the AS path against a sequence of one or more values or parameters, use the as-path neighbor-is command in route-policy configuration mode.
as-path neighbor-is as-number-list [exact]
Syntax Description
as-number-list |
Numbers or parameters, enclosed in single quotation marks, that represent a sequence of autonomous system numbers. Range for 2-byte numbers is 1 to 65535. Range for 4-byte numbers is 1.0 to 65535.65535. |
exact |
(Optional) Specifies that with the exact keyword, the as-number-list value must identically match the AS path for the route; without the exact keyword, any element in the as-number-list argument matches one or more occurrences of that element in the AS path for the route. |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
The as-number-list 4-byte number range 1.0 to 65535.65535 was supported. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the as-path neighbor-is command as a conditional expression within an if statement to test the autonomous system number or numbers at the head of the AS path against a sequence of one or more integral values or parameters. In other words, to test to learn if the sequence of autonomous system numbers matches the path beginning with the neighboring autonomous system from which this route was heard.
Note For a list of all conditional expressions available within an if statement, see the if command.
This command has an equivalent regular expression (ios-regex). For example, AS path neighbor-is `1' would be `^1_'.
Examples
The following are incomplete configuration examples:
RP/0/RP0/CPU0:router(config-rpl)# if as-path neighbor-is '10' then
RP/0/RP0/CPU0:router(config-rpl-if)# if as-path neighbor-is '$asnum' then
RP/0/RP0/CPU0:router(config-rpl-if)# if as-path neighbor-is '10 20' then
These statements evaluate to true when the first autonomous system numbers on the AS path match, in the same order, the supplied parameters or integer values in the neighbor-is statement. If the neighboring autonomous system location happens to be an AS-set, the operator evaluates to true if the corresponding argument to the neighbor-is operator is an element of the AS-set.
Without the exact keyword, repeated autonomous system numbers in the AS path are ignored. For example,
RP/0/RP0/CPU0:router(config-rpl)# if as-path neighbor-is '10 20' then
matches an AS path beginning
and an AS path beginning:
With the exact keyword, repetitions are not ignored, therefore
RP/0/RP0/CPU0:router(config-rpl)# if as-path neighbor-is '10 20' exact then
matches the second of these AS paths but not the first.
Related Commands
|
|
as-path in |
Matches the AS path of a route to an AS path set. |
as-path length |
Compares the number of ASN in the AS path of a route. |
as-path originates-from |
Compares an AS path to the AS sequence beginning with the AS number that originated a route. |
as-path passes-through |
Verifies if the supplied integer or parameter appears anywhere in the AS path or if the supplied sequence of integers and parameters appears, in the same order, anywhere in the AS path. |
as-path unique-length |
Performs specific checks based on the length of the AS path. |
as-path originates-from
To compare an AS path against the AS sequence beginning with the AS number that originated a route, use the as-path originates-from command in route-policy configuration mode.
as-path originates-from as-number-list [exact]
Syntax Description
as-number-list |
Numbers or parameters, enclosed in single quotation marks, that represent a sequence of autonomous system numbers. Range for 2-byte numbers is 1 to 65535. Range for 4-byte numbers is 1.0 to 65535.65535. |
exact |
(Optional) Specifies that with the exact keyword, the as-number-list value must identically match the AS path for the route; without the exact keyword, any element in the as-number-list argument matches one or more occurrences of that element in the AS path for the route. |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
The as-number-list 4-byte number range 1.0 to 65535.65535 was supported. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the as-path originates-from command as a conditional expression within an if statement to compare an AS path to the autonomous system sequence.
Note For a list of all conditional expressions available within an if statement, see the if command.
The originates-from operator is similar to the neighbor-is operator, except that it looks at the autonomous system number at the opposite end of the AS path. In other words, it is comparing to the autonomous system that originated the route. It can take numbers or parameters, enclosed in single quotation marks, that represent a sequence of autonomous system numbers. When more than one number is specified in the list, the sequence of autonomous system numbers listed must appear as a subsequence in the AS path, with the last number corresponding to the autonomous system that originated the route.
Examples
The following are incomplete configuration examples:
RP/0/RP0/CPU0:router(config-rpl)# if as-path originates-from '10 11' then
RP/0/RP0/CPU0:router(config-rpl-if)# if as-path originates-from '$asnum 11' then
The first line of the preceding example evaluates to true if autonomous system 11 originated the route and then advertised it to autonomous system 10, from which the route was eventually propagated to us. In the case where the route has been aggregated, and the location of the originating autonomous system contains an AS-set, the originates-from operator evaluates to true if the argument to the originates-from operator is contained in the AS-set.
Without the exact keyword, repeated autonomous system numbers in the AS path are ignored. For example,
RP/0/RP0/CPU0:router(config-rpl)# if as-path originates-from '10 11' then
matches an autonomous system path ending
and an autonomous system path ending
With the exact keyword, repetitions are not ignored, therefore
RP/0/RP0/CPU0:router(config-rpl)# if as-path originates-from '10 11' exact then
matches the second of these autonomous system paths but not the first.
Related Commands
|
|
as-path in |
Matches the AS path of a route to an AS path set. |
as-path length |
Compares the number of ASN in the AS path of a route |
as-path passes-through |
Verifies if the supplied integer or parameter appears anywhere in the AS path or if the supplied sequence of integers and parameters appears, in the same order |
as-path unique-length |
Performs specific checks based on the length of the AS path. |
as-path passes-through
To verify if the supplied integer or parameter appears anywhere in the AS path or if the supplied sequence of integers and parameters appears, in the same order, anywhere in the AS path, use the as-path passes-through command in route-policy configuration mode.
as-path passes-through as-number-list [exact]
Syntax Description
as-number-list |
Numbers or parameters, enclosed in single quotation marks, that represent a sequence of autonomous system numbers. Range for 2-byte numbers is 1 to 65535. Range for 4-byte numbers is 1.0 to 65535.65535. |
exact |
(Optional) Specifies that with the exact keyword, the as-number-list value must identically match the AS path for the route; without the exact keyword, any element in the as-number-list argument matches one or more occurrences of that element in the AS path for the route. |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
The as-number-list 4-byte number range 1.0 to 65535.65535 was supported. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the as-path passes-through command as a conditional expression within an if statement to verify if the specified integer or parameter appears anywhere in the AS path or if the sequence of integers and parameters appears.
Note For a list of all conditional expressions available within an if statement, see the if command.
The passes-through operator takes a sequence of integers or parameters, enclosed in single quotation marks, as an argument. It can also take a single integer or parameter as an argument. It evaluates to true if the supplied integer or parameter appears anywhere in the AS path, or if the supplied sequence of integers and parameters appears, in the same order, anywhere in the AS path. This includes the originates-from or neighbor-is location in the AS path.
Examples
The following are incomplete configuration examples:
RP/0/RP0/CPU0:router(config-rpl)# if as-path passes-through '10' then
RP/0/RP0/CPU0:router(config-rpl-if)# if as-path passes-through '$asnum' then
RP/0/RP0/CPU0:router(config-rpl-if)# if as-path passes-through '10 11' then
RP/0/RP0/CPU0:router(config-rpl-if)# if as-path passes-through '10 $asnum 12' then
Without the exact keyword, repeated autonomous system numbers in the AS path are ignored. For example:
RP/0/RP0/CPU0:router(config-rpl)# if as-path passes-through '9 10 11' then
matches an AS path containing
and an AS path containing:
With the exact keyword, repetitions are not ignored. Therefore:
RP/0/RP0/CPU0:router(config-rpl)# if as-path passes-through '9 10 11' exact then
matches the second of these AS paths but not the first.
Related Commands
as-path-set
To create a named AS path set, use the as-path-set command in global configuration mode. To remove the named AS path set, use the no form of this command.
as-path-set name
no as-path-set name
Syntax Description
name |
Name of the AS path set. |
Defaults
No default behavior or values
Command Modes
Global configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the as-path-set command to create a named AS path set.
An AS path set comprises operations for matching an AS path attribute.
This command enters AS path set configuration mode, in which you can use the ios-regex keyword to indicate the type of regular expression. Single quotation marks are required around the regular expression.
The inline set form is a parenthesized list of comma-separated expressions.
See the "Understanding Regular Expressions, Special Characters and Patterns" appendix in Cisco IOS XR Getting Started Guide for information about forming regular expressions.
Examples
The following is a sample definition of an AS path set named aset1:
RP/0/RP0/CPU0:router(config)# as-path-set aset1
RP/0/RP0/CPU0:router(config-as)# ios-regex '_42$',
RP/0/RP0/CPU0:router(config-as)# ios-regex '_127$'
RP/0/RP0/CPU0:router(config-as)# end-set
This AS path set is composed of two elements. When used in a matching operation, this AS path set matches any route whose AS path ends with either the autonomous system number 42 or 127.
The following is a sample of an inline set:
RP/0/RP0/CPU0:router(config-rpl)# if as-path in (ios-regex '_42$', ios-regex$ '_127$')
RP/0/RP0/CPU0:router(config-rpl-if)# pass
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)#
as-path unique-length
To perform specific checks based on the length of the AS path (match against the number of unique ASNs in the AS path), use the as-path unique-length command in route-policy configuration mode.
as-path unique-length {eq | is | ge | le} {number | parameter}
Syntax Description
eq | is | ge | le |
Equal to; greater than or equal to; less than or equal to. |
number |
Value assigned to an 11-bit unsigned integer. Range is from 0 to 2047. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the as-path unique-length command as a conditional expression within an if statement to perform a match based on the length of the AS path.
Note For a list of all conditional expressions available within an if statement, see the if command.
The unique-length operator is similar to the length operator, except that when an AS path has been padded with the same autonomous system number multiple times, the operator counts only one when the route is padded. Therefore, given an AS path of 333 333 111 222 123 444 444 444, the unique-length operator would return a value of 5, whereas the length operator would return a value of 8.
Examples
The following example shows show to perform checks based on the AS path length. If the AS path matches the specified values, the local preference is set to 100:
RP/0/RP0/CPU0:router(config-rpl)# if as-path unique-length eq 10 then
RP/0/RP0/CPU0:router(config-rpl-if)# if as-path unique-length ge 10 then
RP/0/RP0/CPU0:router(config-rpl-if)# if as-path unique-length le 10 then
RP/0/RP0/CPU0:router(config-rpl)# if as-path unique-length eq $integerparam then
RP/0/RP0/CPU0:router(config-rpl-if)# if as-path unique-length ge $geparam then
RP/0/RP0/CPU0:router(config-rpl-if)# if as-path unique-length le $leparam then
RP/0/RP0/CPU0:router(config-rpl)# set local-preference 100
RP/0/RP0/CPU0:router(config-rpl)# endif
Related Commands
|
|
as-path length |
Performs conditional checks based on the length of the AS path. |
community is-empty
To check if a route has no community attributes associated with it, use the community is-empty command in route-policy configuration mode.
community is-empty
Syntax Description
This command has no arguments or keywords.
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the community is-empty command as a conditional expression within an if statement to check if a route has community attributes associated with it.
Note For a list of all conditional expressions available within an if statement, see the if command.
This command takes no arguments and evaluates to true only if the route has no community attributes associated with it.
Examples
In the following example, if the route has no community attributes associated with it, then the local preference is set to 100:
RP/0/RP0/CPU0:router(config-rpl)# if community is-empty then
RP/0/RP0/CPU0:router(config-rpl-if)# set local-preference 100
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)#
community matches-any
To match any elements of a community set, use the community matches-any command in route-policy configuration mode.
community matches-any {community-set-name | inline-community-set | parameter}
Syntax Description
community-set-name |
Name of a community set. |
inline-community-set |
Inline community set. The inline community set must be enclosed in parentheses. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The BGP community matching operators were enhanced to allow comparisons on ranges and regular expressions. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
The parameter argument was added. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the community matches-any command as a conditional expression within an if statement to match any element of a community set.
Note For a list of all conditional expressions available within an if statement, see the if command.
A simple condition using the matches-any operator evaluates as true if at least one community element of the community attribute for the route matches an element in the community set operand. If no community in the route matches any of the specifications in the named or inline set, then the condition evaluates to false. Likewise, when there is no community at all in the route, the condition evaluates to false.
Matching of a community in the route to a specification in a named or an inline set is intuitive. If the community specification in a set is the familiar colon-separated decimal 16-bit numbers specification, or one of the well-known communities, the community matches the specification if the specification denotes the same 32-bit number as that in the route. If the community specification uses a wildcard, then the community in the route matches if it is one of the many communities denoted by the wildcard specification. In inline sets, community specifications may be parameterized, in which case the relevant matching is done when the value of the parameter has been supplied.
Communities may also be matched using range and regular expression operators. Range specifications are entered as follows: [low-value..high-value]. Either or both colon-separated halves of a community value may contain a range. The following are valid range specifications:
In addition, the private-as keyword may be used to specify the range from 64512 to 65534. Regular expressions are specified as the ios-regex keyword followed by a valid regular expression string.
Community values from the route are matched one at a time to the match specifications. Therefore, regex match specifications are expected to represent one individual community value and not a sequence of community values.
Examples
In the following example, a named community set called my-community-set and a route policy called community-matches-any-example are created. The policy sets the local-preference to 100 for any route that has one or more of the communities in the my-community-set community set. If the route does not have any of these communities, the policy checks whether it has any communities whose first half is in the range from 10 to 25 and whose second half is the value 35, in which case it sets the local-preference to 200. Otherwise, it checks for a community value in the range of 30:100 to 30:500, in which case it sets the local-preference to 300.
RP/0/RP0/CPU0:router(config)# community-set my-community-set
RP/0/RP0/CPU0:router(config-comm)# 10:20,
RP/0/RP0/CPU0:router(config-comm)# 10:30,
RP/0/RP0/CPU0:router(config-comm)# 10:40
RP/0/RP0/CPU0:router(config-comm)# end-set
RP/0/RP0/CPU0:router(config)# route-policy community-matches-any-example
RP/0/RP0/CPU0:router(config-rpl)# if community matches-any my-community-set then
RP/0/RP0/CPU0:router(config-rpl-if)# set local-preference 100
RP/0/RP0/CPU0:router(config-rpl-if)# elseif community matches-any ([10..25]:35) then
RP/0/RP0/CPU0:router(config-rpl-elseif)# set local-preference 200
RP/0/RP0/CPU0:router(config-rpl-elseif)# elseif community matches-any (30:[100..500]) then
RP/0/RP0/CPU0:router(config-rpl-elseif)# set local-preference 300
RP/0/RP0/CPU0:router(config-rpl-elseif)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
Related Commands
community matches-every
To match every element of a community set, use the community matches-every command in route-policy configuration mode.
community matches-every {community-set-name | inline-community-set | parameter}
Syntax Description
community-set-name |
Name of a community set. |
inline-community-set |
Inline community set. The inline community set must be enclosed in parentheses. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The BGP community matching operators were enhanced to allow comparisons on ranges and regular expressions. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
The parameter argument was added. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the community matches-every command as a conditional expression within an if statement to match every element of a community set.
Note For a list of all conditional expressions available within an if statement, see the if command.
A simple condition using the matches-every operator evaluates as true if every specification in the named set or inline set specified matches at least one community value in the route. If any community specification in the named or inline set is not matched, then the operation evaluates to false.
Matching of a community in the route to a specification in a named or an inline set is intuitive. If the community-specification in a set is the familiar colon-separated decimal 16-bit numbers specification, or one of the well-known communities, the community matches the specification if the specification denotes the same 32-bit number as that in the route. If the community specification uses a wildcard, then the community in the route matches if it is one of the many communities denoted by the wildcard specification. In inline sets, community specifications may be parameterized, in which case the relevant matching is done when the value of the parameter has been supplied.
Communities may also be matched using range and regular expression operators. Range specifications are entered as follows: [low-value..high-value]. Either or both colon-separated halves of a community value may contain a range. The following are valid range specifications:
Therefore, a matches-every operation with two community range specifications means that a community must be present in the route that corresponds to each range. For example, in the following statement:
if community matches-every (10:[100..200],20:[100..200]) then
the statement evaluates as true if one or more communities in the route lie in the range 10:[100.200] and one or more communities in the route lie in the range 20:[100..200].
In addition, the private-as keyword may be used to specify the range from 64512 to 65534.
Regular expressions are specified as the ios-regex keyword followed by a valid single-quoted regular expression string. Community values from the route are matched one at a time against the match specifications. Therefore, regex match specifications are expected to represent one individual community value and not a sequence of community values.
Examples
In the following example, the route policy named community-matches-every-example sets the local-preference value to 100 for all routes that have all three communities in the my-community-set community set. Routes that do not have all three communities but have a community that matches the first regular expression match have the local-preference value set to 200. Finally, any remaining routes that match the last regular expression have the local-preference values set to 300.
RP/0/RP0/CPU0:router(config)# community-set my-community-set
RP/0/RP0/CPU0:router(config-comm)# 10:20,
RP/0/RP0/CPU0:router(config-comm)# 10:30,
RP/0/RP0/CPU0:router(config-comm)# 10:40
RP/0/RP0/CPU0:router(config-comm)# end-set
RP/0/RP0/CPU0:router(config)# route-policy community-matches-every-example
RP/0/RP0/CPU0:router(config-rpl)# if community matches-every my-community-set then
RP/0/RP0/CPU0:router(config-rpl-if)# set local-preference 100
RP/0/RP0/CPU0:router(config-rp-elseif)# elseif community matches-every (ios-regex
'_10:[0-9]0_') then
RP/0/RP0/CPU0:router(config-rpl-elseif)# set local-preference 200
RP/0/RP0/CPU0:router(config-rpl-elseif)# elseif community matches-every
(ios-regex'_20:[0-9]0_') then
RP/0/RP0/CPU0:router(config-rpl-elseif)# set local-preference 300
RP/0/RP0/CPU0:router(config-rpl-elseif)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
Related Commands
community-set
To define a community set, use the community-set command in global configuration mode. To remove the community set, use the no form of this command.
community-set name
no community-set name
Syntax Description
name |
Name of the community set. |
Defaults
No default behavior or values
Command Modes
Global configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Regular expressions and ranges can be specified in a community set to support the matching or deleting of communities using ranges or regular expressions in named community sets. An attempt to use a community set that contains a range or regular expression to set a community value is rejected when an attempt to attach such a policy is made.
A community set holds community values for matching against the Border Gateway Protocol (BGP) community attribute. A community is a 32-bit quantity. For notational convenience, each community value must be split in half and expressed as two unsigned decimal integers in the range from 0 to 65535, separated by a colon.
The inline form of a community set also supports parameterization. Each 16-bit portion of the community may be parameterized.
The routing policy language (RPL) provides symbolic names for the standard well-known community values: internet is 0:0, no-export is 65535:65281, no-advertise is 65535:65282, and local-as is 65535:65283.
RPL also provides a facility for using wildcards in community specifications. A wildcard is specified by inserting an asterisk (*) in place of one of the 16-bit portions of the community specification, which indicates that any value for that portion of the community matches.
Every community set must contain at least one community value. An empty community set is invalid and the policy configuration system rejects it.
Examples
In the following example, a community set named cset1 is created:
RP/0/RP0/CPU0:router(config)# community-set cset1
RP/0/RP0/CPU0:router(config-comm)# 12:34,
RP/0/RP0/CPU0:router(config-comm)# 12:56,
RP/0/RP0/CPU0:router(config-comm)# 12:78,
RP/0/RP0/CPU0:router(config-comm)# internet
RP/0/RP0/CPU0:router(config-comm)# end-set
In the following example, a community set named cset2 is created:
RP/0/RP0/CPU0:router(config)# community-set cset2
RP/0/RP0/CPU0:router(config-comm)# 123:456,
RP/0/RP0/CPU0:router(config-comm)# no-advertise,
RP/0/RP0/CPU0:router(config-comm)# end-set
In the following example, a community set named cset3 is created. This policy uses wildcards and matches all communities where the autonomous system part of the community is 123.
RP/0/RP0/CPU0:router(config)# community-set cset3
RP/0/RP0/CPU0:router(config-comm)# 123:*
RP/0/RP0/CPU0:router(config-comm)# end-set
delete community
To delete community attributes associated with a Border Gateway Protocol (BGP) route, use the delete community command in route-policy configuration mode.
delete community {all | in {community-set-name | inline-community-set | parameter} | not in {community-set-name | inline-community-set | parameter}}
Syntax Description
all |
Removes all communities except the well-known communities. |
in |
Removes any communities associated with the route that are listed in either the named community set or the inline community set. |
community-set-name |
Name of a community set. |
inline-community-set |
Inline community set. The inline community set must be enclosed in parentheses. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
not in |
Removes all communities that are not listed in either the named community set or the inline community set, and are not well-known communities. |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The BGP community deletion operations were extended to allow communities that match a range specification or a regular expression to be deleted. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
The parameter argument was added. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the delete community command to delete community attributes associated with a BGP route.
Note The delete community command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
Communities are 32-bit values carried in Border Gateway Protocol (BGP) routes. Each route may have zero or more communities in an unordered list.
You can remove a well-known community (internet, no-export, no-advertise, or local-as) from a route, but this removal must be done explicitly. This command should be used with a degree of caution. In general, few circumstances exist in which you would need to remove a well-known community.
Examples
The following example shows how to delete any communities associated with the routes that are listed in either the named community set or inline community set, respectively.
RP/0/RP0/CPU0:router(config-rpl)# delete community in my_community_set
RP/0/RP0/CPU0:router(config-rpl)# delete community in (10:[0..50],20:[60..80])
The following example shows how to remove all communities including well-known communities.
RP/0/RP0/CPU0:router(config-rpl)# delete community in (internet, no-export, no-advertise,
local- as, *:*)
The following example shows how to remove all communities except for the well-known communities.
RP/0/RP0/CPU0:router(config-rpl)# delete community all
The following example shows how to delete the well-known community value internet from a route:
RP/0/RP0/CPU0:router(config-rpl)# delete community in (internet)
delete extcommunity rt
To delete route target (RT) extended community attributes associated with a Border Gateway Protocol (route), use the delete extcommunity rt command in route-policy configuration mode.
delete extcommunity rt {all | in {extcommunity-set-name | inline-extcommunity-set | parameter} | not in {extcommunity-set-name | inline-extcommunity-set | parameter}}
Syntax Description
all |
Removes all extended communities. |
in |
Removes any extended communities associated with the routes that are listed in either the named extended community set or the inline extended community set. |
extcommunity-set-name |
Name of an extended community set. |
inline-extcommunity-set |
Inline extended community set. The inline extended community set must be enclosed in parentheses. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
not in |
Removes all extended communities that are not listed in either the named extended community set or the inline extended community set, and are not well-known extended communities. |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
The parameter argument was added. |
Release 3.5.0 |
Support was added for the usage of Wildcards (*) and regular expressions for extended community set elements. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the delete extcommunity rt command to delete extended community values from a BGP route target extended community list in a route.
Note The delete extcommunity rt command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
Extended communities are similar to regular Border Gateway Protocol (BGP) communities but contain more data and have a richer structure for encoding information in them.
Extended communities can be in the following forms: SoO:AS:tag, SoO:IP:tag, RT:AS:tag, or RT:IP:tag.
Wildcards (*) and regular expressions are allowed for extended community set elements.
The forms of this command that take a named extended community set or an inline extended community set value as arguments are equivalent. They delete any extended communities that are listed in either the named set or the inline set, respectively.
Examples
In the following example, all extended communities are deleted:
RP/0/RP0/CPU0:router(config-rpl)# delete extcommunity rt all
In this example, any extended communities that are listed in my-extcommunity-set are deleted:
RP/0/RP0/CPU0:router(config-rpl)# delete extcommunity rt in my-extcommunity-set
In this example, extended communities associated with the route listed in the named inline extended community sets are deleted:
RP/0/RP0/CPU0:router(config-rpl)# delete extcommunity rt in (67:29, 67:55)
destination in
To match a destination entry in a named prefix set or inline prefix set, use the destination in command in route-policy configuration mode.
destination in {prefix-set-name | inline-prefix-set | parameter}
Syntax Description
prefix-set-name |
Name of a prefix set. |
inline-prefix-set |
Inline prefix set. The inline prefix set must be enclosed in parentheses. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
The parameter argument was added. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the destination in command as a conditional expression within an if statement to match a destination entry in a named prefix set or inline prefix set.
Note For a list of all conditional expressions available within an if statement, see the if command.
This command takes either a named prefix set or an inline prefix set value as an argument. The condition returns true if the destination entry matches any entry in the prefix set or inline prefix set. An attempt to match a destination using a prefix set that is defined but contains no elements returns false.
The routing policy language (RPL) provides the ability to test destinations for a match to a list of prefix match specifications using the in operator. The destination in command is protocol-independent.
In Border Gateway Protocol (BGP), the destination of a route is also known as its network-layer reachability information (NLRI). It comprises a prefix value and a mask length.
RPL supports both 32-bit IPv4 prefixes, specified in dotted-decimal format, and 128-bit IPv6 prefixes, specified in colon-separated hexadecimal format.
Examples
In the following example, a prefix set named my-prefix-set is defined and a route policy named use-destination-in is created. Within the use-destination-in route policy, the destination in command is used within an if statement to learn if the destination is in the prefix-set named my-prefix-set. If it is, then local preference is set to 100. If it is not in my-prefix-set but does match the next prefix specifications, then local preference is set to 200.
RP/0/RP0/CPU0:router(config)# prefix-set my-prefix-set
RP/0/RP0/CPU0:router(config-pfx)# 10.0.0.1/32,
RP/0/RP0/CPU0:router(config-pfx)# fe80::203:0:0:0/64,
RP/0/RP0/CPU0:router(config-pfx)# 10.0.0.2/24 le 32
RP/0/RP0/CPU0:router(config-pfx)# end-set
RP/0/RP0/CPU0:router(config)# route-policy use-destination-in
RP/0/RP0/CPU0:router(config-rpl)# if destination in my-prefix-set then
RP/0/RP0/CPU0:router(config-rpl-if)# set local-preference 100
RP/0/RP0/CPU0:router(config-rpl-if)# elseif destination in (10.0.0.1/32, 10.0.0.2/24 le
32) then
RP/0/RP0/CPU0:router(config-rpl-elseif)# set local-preference 200
RP/0/RP0/CPU0:router(config-rpl-elseif)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
In the following example, a prefix set named ipv6-prefix-set is defined and a route policy named ipv6-destination-in is created. Within the ipv6-destination-in route policy, the destination in command is used within an if statement to learn if the destination is in the prefix-set named ipv6-prefix-set. If it is, then the next hop is set to 2001:abcd:fedc::1. If it is not in ipv6-prefix-set but does match the next prefix specifications, then the next hop is set to 1111:2222:3333:4444:5555:6666:7777:8888.
RP/0/RP0/CPU0:router(config)# prefix-set ipv6-prefix-set
RP/0/RP0/CPU0:router(config-pfx)# 2001:0:0:1::/64,
RP/0/RP0/CPU0:router(config-pfx)# 2001:0:0:2::/64,
RP/0/RP0/CPU0:router(config-pfx)# 2001:0:0:3::/64,
RP/0/RP0/CPU0:router(config-pfx)# 2001:0:0:4::/64
RP/0/RP0/CPU0:router(config-pfx)# end-set
RP/0/RP0/CPU0:router(config)# route-policy ipv6-destination-in
RP/0/RP0/CPU0:router(config-rpl)# if destination in ipv6-prefix-set then
RP/0/RP0/CPU0:router(config-rpl-if)# set next-hop 2001:abcd:fedc::1
RP/0/RP0/CPU0:router(config-rpl-if)# elseif destination in (2001::1, 2002:1:2:3::/64) then
RP/0/RP0/CPU0:router(config-rpl-elseif)# set next-hop
1111:2222:3333:4444:5555:6666:7777:8888
RP/0/RP0/CPU0:router(config-rpl-elseif)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
done
To stop executing a policy and accept the route, use the done command in route-policy configuration mode.
done
Syntax Description
This command has no arguments or keywords.
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.5.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the done command to stop executing the policy and accept the route.
Note The done command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
When encountering a done statement the route is passed and no further policy statements are executed. All modifications made to the route prior to the done statement are still valid.
Note The default action of a route policy is to drop or discard any routes that have not been either explicitly passed or for which no attempt has been made to modify with an action. The routing policy language (RPL) does not have specific "match clauses," which means the default drop behavior is controlled by whether a route has been explicitly passed or an attempt has been to modify the route using an action statement.
Examples
In the following example, if the destination match succeeds for 29.0.0.0/8 le 32, the execution continues past set community 102:12 and onto the next statement. If the destination match succeeds for 39.0.0.0/8 le 32 execution, then the policy execution stops when in encounters the done statement.
RP/0/RP0/CPU0:router(config)# route-policy done_st_example
RP/0/RP0/CPU0:router(config-rpl)# if destination in (29.0.0.0/8 le 32) then
RP/0/RP0/CPU0:router(config-rpl-if)# set community 102:12
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)# if destination in (39.0.0.0/8 le 32) then
RP/0/RP0/CPU0:router(config-rpl-if)# set community 102:39
RP/0/RP0/CPU0:router(config-rpl-if)# done
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)# if destination in (49.0.0.0/8 le 32) then
RP/0/RP0/CPU0:router(config-rpl-if)# set community 102:49
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)# if destination in (59.0.0.0/8 le 32) then
RP/0/RP0/CPU0:router(config-rpl-if)# set community 102:59
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
drop
To discard a route, use the drop command in route-policy configuration mode.
drop
Syntax Description
This command has no arguments or keywords.
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the drop command within a route policy to drop a route.
Note The drop command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
This command causes the route to be dropped. After a route is dropped, no further execution of policy occurs. Therefore, if after executing the first two statements of a policy the drop statement is encountered, the route is discarded and execution stops immediately even when the policy contains further statements.
Note The default action of a route policy is to drop or discard any routes that have not been either explicitly passed or attempted to be modified with an action. The routing policy language (RPL) does not have specific "match clauses," which means the default drop behavior is controlled by whether a route has been explicitly passed or an attempt has been to modify the route using an action statement.
Examples
In the following example, any route with a destination address contained within the prefix set pset1 is dropped:
RP/0/RP0/CPU0:router(config-rpl)# if destination in pset1 then
RP/0/RP0/CPU0:router(config-rpl-if)# drop
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)#
edit
To edit the contents of a route policy, a prefix set, an AS path set, a community set, or an extended community set, use the edit command in EXEC mode.
edit {route-policy | prefix-set | as-path-set | community-set | extcommunity-set {rt | soo}| policy-global | rd-set} name [nano | emacs | vim | inline {add | prepend | remove} set-element]
Syntax Description
route-policy |
Edits the contents of a route policy. |
prefix-set |
Edits the contents of a prefix set. |
as-path-set |
Edits the contents of an AS path set. |
community-set |
Edits the contents of a community set. |
extcommunity-set |
Edits the contents of an extended community set of the specified type. |
rt |
Edits the BGP route target (RT) extended community. |
soo |
Edits the BGP site of origin (SoS) extended community. |
policy-global |
Edits the contents of policy-global definitions. |
rd-set |
Edits the contents of a route-distinguisher set. |
name |
Name of a route policy, a prefix set, an AS path set, a community set, or an extended community set, RD set, or global parameters. |
nano |
(Optional) Uses GNU Nano text editor. |
emacs |
(Optional) Uses Micro Emacs editor. |
vim |
(Optional) Uses VI Improved editor. |
inline |
(Optional) Uses the command line. |
add |
Appends the element to the set. |
prepend |
Prepends the element to the set. |
remove |
Removes the element from the set. |
set-element |
Value of the set element. Note To inline edit multiple set elements separated with comma, use quotes to club the entries as a single argument. Example: edit extcommunity-set rt rt_set inline add "4:4,5:4". |
Defaults
Default editor is GNU nano text editor
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
Added vim keyword. |
Release 3.4.0 |
The policy-global keyword was added. |
Release 3.5.0 |
The nano keyword was added and GNU nano text editor became the default editor type. |
Release 3.6.0 |
The following keywords and arguments were added: •inline •add •prepend •remove •set-element |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the edit command to edit the contents of a route policy, a prefix set, an AS path set, a community set, an extended community set, a global policy, or a route destination set.
After editing with Nano, save the edit buffer and exit the editor using the Ctrl-X keystroke.
After editing with Emacs, save the editor buffer by using the Ctrl-X and Ctrl-S keystrokes. To save and exit the editor, use the Ctrl-X and Ctrl-C keystrokes.
After editing with VIM, to write to a current file and exit use the :wq or :x or ZZ keystrokes. To quit and confirm, use the :q keystrokes. To quit and discard changes, use the :q! keystrokes.
Examples
In the following example, the policy_A policy is opened in the editor:
RP/0/RP0/CPU0:router# edit route-policy policy_A
----------------------------------------
== MicroEMACS 3.8b () == rpl_edit.139281 ==
if destination in (2001::/8) then
== MicroEMACS 3.8b () == rpl_edit.139281 ==
83 bytes parsed in 1 sec (82)bytes/sec
1 items committed in 1 sec (0)items/sec
Updated Commit database in 1 sec
If there are parse errors, you are asked whether editing should continue:
RP/0/RP0/CPU0:router#edit route-policy policy_B
== MicroEMACS 3.8b () == rpl_edit.141738
if destination in (2001::/8) then
== MicroEMACS 3.8b () == rpl_edit.141738 ==
105 bytes parsed in 1 sec (103)bytes/sec
% Syntax/Authorization errors in one or more commands.!! CONFIGURATION
FAILED DUE TO SYNTAX/AUTHORIZATION ERRORS
if destination in (2001::/8) then
If you answer yes, the editor continues on the text buffer from where you left off. If you answer no, the running configuration is not changed and the editing session is ended.
After the policy is opened, it may be manipulated using normal editor commands, then saved and committed to the running configuration.
end-global
To end the definition of global parameters and exit global parameter configuration mode, use the end-policy command in global parameter configuration mode.
end-global
Syntax Description
This command has no arguments or keywords.
Defaults
No default behavior or values
Command Modes
Global parameter configuration
Command History
|
|
Release 3.4.0 |
This command was introduced on the Cisco CRS-1 Cisco XR 12000 Series Router. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the end-global command to end the definition of global parameters and exit global parameter configuration mode.
Examples
In the following example, the end-global command ends the definition of global parameters:
RP/0/RP0/CPU0:router(config)# policy-global
RP/0/RP0/CPU0:router(config-rp-gl)# glbpathtype `ebgp'
RP/0/RP0/CPU0:router(config-rp-gl)# glbtag `100'
RP/0/RP0/CPU0:router(config-rp-gl)# end-global
Related Commands
end-policy
To end the definition of a route policy and exit route-policy configuration mode, use the end-policy command in route-policy configuration mode.
end-policy
Syntax Description
This command has no arguments or keywords.
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the end-policy command to end the definition of a route policy and exit route-policy configuration mode.
Examples
In the following example, the end-policy command ends the definition of a route policy:
RP/0/RP0/CPU0:router(config)# route-policy med-to-local-pref
RP/0/RP0/CPU0:router(config-rpl)# if med eq 150 then
RP/0/RP0/CPU0:router(config-rpl-if)# set local-preference 10
RP/0/RP0/CPU0:router(config-rpl-if)# elseif med eq 200 then
RP/0/RP0/CPU0:router(config-elseif)# set local-preference 60
RP/0/RP0/CPU0:router(config-elseif)# elseif med eq 250 then
RP/0/RP0/CPU0:router(config-elseif)# set local-preference 0
RP/0/RP0/CPU0:router(config-elseif)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
Related Commands
end-set
To end the definition of an AS path set, a prefix set, a community set, an extended community set, or an RD set and return to global configuration mode, use the end-set command in route-policy configuration mode.
end-set
Syntax Description
This command has no arguments or keywords.
Defaults
No default behavior or values
Command Modes
AS path set configuration
Prefix set configuration
Community set configuration
Extended community set configuration
Route distinguisher set configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
Added support functionality for the rd-set command. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the end-set command to end the definition of an AS path set, a prefix set, a community set, or an extended community set.
Examples
In the following example, the end-set command ends the definition of an AS path set named aset1:
RP/0/RP0/CPU0:router(config)# as-path-set aset1
RP/0/RP0/CPU0:router(config-as)# ios-regex '_42$',
RP/0/RP0/CPU0:router(config-as)# ios-regex '_127$'
RP/0/RP0/CPU0:router(config-as)# end-set
RP/0/RP0/CPU0:router(config)#
The following example shows how to create an RD set called my_rd_set and use the end-set command to end the definition:
RP/0/RP0/CPU0:router(config)# rd-set my_rd_set
RP/0/RP0/CPU0:router(config-rd)# 172.16.0.0/16:*,
RP/0/RP0/CPU0:router(config-rd)# 172.17.0.0/16:100,
RP/0/RP0/CPU0:router(config-rd)# 192:*,
RP/0/RP0/CPU0:router(config-rd)# 192:100
RP/0/RP0/CPU0:router(config-rd)# end-set
extcommunity rt is-empty
To check if a Border Gateway Protocol (BGP) route has route target (RT) extended community attributes associated with it, use the extcommunity rt is-empty command in route-policy configuration mode.
extcommunity rt is-empty
Syntax Description
This command has no arguments or keywords.
Defaults
No default behavior or value
Command Modes
Route-policy configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
|
This command replaced the extcommunity is-empty command. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the extcommunity rt is-empty command as a conditional expression within an if statement to check if a BGP route has extended community attributes associated with it.
Note For a list of all conditional expressions available within an if statement, see the if command.
The is-empty operator takes no arguments and evaluates to true if the route has no extended community attributes associated with it.
Examples
In the following example, if the extended community is empty, then the local preference is set to 100:
RP/0/RP0/CPU0:router(config)# route-policy extcommunity-is-empty-example
RP/0/RP0/CPU0:router(config-rpl)# if extcommunity rt is-empty then
RP/0/RP0/CPU0:router(config-rpl-if)# set local-preference 100
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
extcommunity rt matches-any
To match any element of a Border Gateway Protocol (BGP) route target (RT) extended community set, use the extcommunity rt matches-any command in route-policy configuration mode.
extcommunity rt matches-any {extcommunity-set-name | inline-extcommunity-set | parameter}
Syntax Description
extcommunity-set-name |
Name of an RT extended community set. |
inline-extcommunity-set |
Inline RT extended community set. The inline extended community set must be enclosed in parentheses. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
|
This command replaced the extcommunity matches-any command. |
Release 3.4.0 |
The parameter argument was added. |
Release 3.5.0 |
Wildcards (*) and regular expressions are allowed for extended community set elements. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the extcommunity rt matches-any command as a conditional expression within an if statement to match elements of an extended community set.
Note For a list of all conditional expressions available within an if statement, see the if command.
A simple condition using the matches-any operator evaluates as true if at least one extended community in the route matches an extended community specification in the named or inline set. If no extended community in the route matches any of the specifications in the named or inline set, then this simple condition evaluates to false. Likewise, when there is no extended community at all in the route, the condition evaluates to false.
Matching an extended community in the route to a specification in a named or an inline set is intuitive. In inline sets, extended community specifications may be parameterized, in which case the relevant matching is done when the value of the parameter has been supplied.
Examples
In the following example, an extended community set named my-extcommunity-set and a parameterized route-policy named my-extcommunity-set-example($tag,$ip) are defined. The extcommunity rt matches-any command is used in an if statement such that if at least one extended community in the route matches an extended community specification in the named set, then the local preference is set to 100. If there is no extended community in the route that matches any of the specifications in the named set, then the condition evaluates as false and the extended community is compared to the inline extended sets.
RP/0/RP0/CPU0:router(config)# extcommunity-set rt my-extcommunity-set
RP/0/RP0/CPU0:router(config-ext)# 10:615,
RP/0/RP0/CPU0:router(config-ext)# 10:6150,
RP/0/RP0/CPU0:router(config-ext)# 15.15.15.15:15
RP/0/RP0/CPU0:router(config-ext)# end-set
RP/0/RP0/CPU0:router(config)# route-policy my-extcommunity-set-example($tag,$ip)
RP/0/RP0/CPU0:router(config-rpl)# if extcommunity rt matches-any my-extcommunity-set then
RP/0/RP0/CPU0:router(config-rpl-if)# set local-preference 100
RP/0/RP0/CPU0:router(config-rpl-if)# elseif extcommunity rt matches-any (10:20, 10:$tag)
then
RP/0/RP0/CPU0:router(config-rpl-elseif)# set local-preference 200
RP/0/RP0/CPU0:router(config-rpl-elseif)# elseif extcommunity rt matches-any ($ip:$tag)
then
RP/0/RP0/CPU0:router(config-rpl-elseif)# set local-preference 300
RP/0/RP0/CPU0:router(config-rpl-elseif)# elseif extcommunity rt matches-any (2.3.4.5:$tag)
then
RP/0/RP0/CPU0:router(config-rpl-elseif)# set local-preference 400
RP/0/RP0/CPU0:router(config-rpl-elseif)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
Related Commands
extcommunity rt matches-every
To match every element of a Border Gateway Protocol (BGP) route target (RT) extended community set, use the extcommunity rt matches-every command in route-policy configuration mode.
extcommunity rt matches-every {extcommunity-set-name | inline-extcommunity-set | parameter}
Syntax Description
extcommunity-set-name |
Name of an RT extended community set. |
inline-extcommunity-set |
Inline RT extended community set. The inline extended community set must be enclosed in parentheses. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
|
This command replaced the extcommunity matches-every command. |
Release 3.4.0 |
The parameter argument was added. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the extcommunity rt matches-every command as a conditional expression within an if statement to match every element of an RT extended community set.
Note For a list of all conditional expressions available within an if statement, see the if command.
A simple condition using the matches-every operator evaluates as true if every extended community value in the extended community attribute for the route matches at least one element of the extended community set or inline set. If no extended community in the route matches any of the specifications in the named or inline set, then this simple condition evaluates to false. Likewise, when there is no extended community at all in the route, the condition evaluates to false.
Matching an extended community in the route to a specification in a named or an inline set is intuitive. In inline sets, extended community specifications may be parameterized, in which case the relevant matching is done when the value of the parameter has been supplied.
Examples
In the following example, an extended community set named my-extcommunity-set and a parameterized route policy named extcommunity-matches-every-example ($as, $tag) are defined. The condition extcommunity rt matches-every is used in an if statement in this policy. If it evaluates to true, the local-preference value is set to 100. If it evaluates to false, the extended community is evaluated using an inline set. If that condition evaluates to true, the local-preference value is set to 200. If it evaluates to false, the local-preference value is set to 300.
RP/0/RP0/CPU0:router(config)# extcommunity-set rt my-extcommunity-set
RP/0/RP0/CPU0:router(config-ext)# 10:20,
RP/0/RP0/CPU0:router(config-ext)# 10:30,
RP/0/RP0/CPU0:router(config-ext)# 10:40
RP/0/RP0/CPU0:router(config-ext)# end-set
RP/0/RP0/CPU0:router(config)# route-policy extcommunity-matches-every-example($as,$tag)
RP/0/RP0/CPU0:router(config-rpl)# if extcommunity rt matches-every my-extcommunity-set
then
RP/0/RP0/CPU0:router(config-rpl-if)# set local-preference 100
RP/0/RP0/CPU0:router(config-rpl-if)# elseif extcommunity rt matches-every (10:20, 10:$tag,
$as:30) then
RP/0/RP0/CPU0:router(config-rpl-elseif)# set local-preference 200
RP/0/RP0/CPU0:router(config-rpl-elseif)# elseif
RP/0/RP0/CPU0:router(config-rpl-elseif)# set local-preference 300
RP/0/RP0/CPU0:router(config-rpl-elseif)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
Related Commands
extcommunity-set cost
To define a cost extended community set, use the extcommunity-set cost command in global configuration mode. To remove the cost extended community set, use the no form of this command.
extcommunity-set cost name
no extcommunity-set cost name
Syntax Description
name |
Name of a cost extended community set. The name argument is case sensitive, can contain any alphanumeric characters, and can be up to 63 characters in length. |
Defaults
No default behavior or values
Command Modes
Global configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and the Cisco XR 12000 Series Router. |
|
This command replaced the extcommunity-set command. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
Support was added for the usage of Wildcards (*) and regular expressions for extended community set elements. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the extcommunity-set cost command to define a cost extended community set.
An extended community set is analogous to a community set except that it contains extended community values instead of regular community values. Extended community values are 64-bit structured values. An extended community set also supports named forms and inline forms.
Cost extended communities can be entered in either of the following formats:
•IGP:id:cost—Considered after IGP distance to next-hop is considered. For example, IGP:2:1025.
•Pre-Bestpath:id:cost—Considered before determining Degree of Preference of a path. For example, Pre-Bestpath:100:966.
where id is in range of 0-255 and cost is in range of 0 to 4294967295
Multiple cost community set clauses can be configured in each route policy block or sequence. Each cost community set clause must have a different ID (0-255). The cost community set clause with the lowest cost-value is preferred by the best path selection process when all other attributes are equal.
As with community sets, the inline form supports parameterization within parameterized policies. Either portion of the extended community value can be parameterized.
Every extended community set must contain at least one extended community value. Empty extended community sets are invalid and the policy configuration system rejects them.
Wildcards (*) and regular expressions are allowed for extended community set elements.
Examples
In the following example, a cost extended community set named extcomm-cost is defined:
RP/0/RP0/CPU0:router(config)# extcommunity-set cost extcomm-cost
RP/0/RP0/CPU0:router(config-ext)# IGP:90:914,
RP/0/RP0/CPU0:router(config-ext)# Pre-Bestpath:91:915
RP/0/RP0/CPU0:router(config-ext)# end-set
extcommunity-set rt
To define a Border Gateway Protocol (BGP) route target (RT) extended community set, use the extcommunity-set rt command in global configuration mode. To remove the RT community set, use the no form of this command.
extcommunity-set rt name
no extcommunity-set rt name
Syntax Description
name |
Name of an RT extended community set. |
Defaults
No default behavior or values
Command Modes
Global configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and the Cisco XR 12000 Series Router. |
|
This command replaced the extcommunity-set command. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the extcommunity-set rt command to define an RT extended community set for BGP.
An extcommunity set RT holds RT extended community values to match against the Border Gateway Protocol (BGP) RT extended community attribute. RT extended communities can be entered in either of the following formats:
•a.b.c.d:n—IPv4 format. For example, 10.0.0.2:666.
•asn:n—BGP ASN format. For example, 10002:666.
n is a number within the range of 1 to 65535.
Examples
In the following example, an RT extended community set named extcomm-rt is defined:
RP/0/RP0/CPU0:router(config)# extcommunity-set rt extcomm-rt
RP/0/RP0/CPU0:router(config-ext)# 10002:666
RP/0/RP0/CPU0:router(config-ext)# 10.0.0.2:666
RP/0/RP0/CPU0:router(config-ext)# end-set
extcommunity-set soo
To define a Border Gateway Protocol (BGP) Site-of-Origin (SoO) extended community set, use the extcommunity-set soo command in global configuration mode. To remove the SoO extended community set, use the no form of this command.
extcommunity-set soo name
no extcommunity-set soo name
Syntax Description
name |
Name of an SoO extended community set. |
Defaults
No default behavior or values
Command Modes
Global configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and the Cisco XR 12000 Series Router. |
|
This command replaced the extcommunity-set command. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the extcommunity-set soo command to define an SoO extended community set.
An extcommunity set soo holds SoO extended community values to match against the Border Gateway Protocol (BGP) SoO extended community attribute. SoO extended communities can be entered in either of the following formats:
•a.b.c.d:n—IPv4 format. For example, 100.100.100.1:153
•asn:n—BGP ASN format. For example, 66:60001
n is a site-specific number.
Examples
In the following example, a SoO extended community set named extcomm-soo is defined:
RP/0/RP0/CPU0:router(config)# extcommunity-set soo extcomm-soo
RP/0/RP0/CPU0:router(config-ext)# 66:60001,
RP/0/RP0/CPU0:router(config-ext)# 77:70001,
RP/0/RP0/CPU0:router(config-ext)# 88:80001,
RP/0/RP0/CPU0:router(config-ext)# 99:90001,
RP/0/RP0/CPU0:router(config-ext)# 100.100.100.1:153
RP/0/RP0/CPU0:router(config-ext)# end-set
extcommunity soo is-empty
To determine if a Border Gateway Protocol (BGP) route has any Site-of-Origin (SoO) extended communities associated with it, use the extcommunity soo is-empty command in route-policy configuration mode.
extcommunity soo is-empty
Syntax Description
This command has no arguments or keywords.
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
|
This command replaced the extcommunity is-empty command. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the extcommunity soo is-empty command as a conditional expression within an if statement to check if a BGP SoO route has extended community attributes associated with it.
Note For a list of all conditional expressions available within an if statement, see the if command.
The is-empty operator takes no arguments and evaluates to true if the route has no SoO extended community attributes associated with it.
Examples
In the following example, if a route has no SoO extended communities associated with it, the local preference is set to 100:
RP/0/RP0/CPU0:router(config)# route-policy extcommunity-is-empty-example
RP/0/RP0/CPU0:router(config-rpl)# if extcommunity soo is-empty then
RP/0/RP0/CPU0:router(config-rpl-if)# set local-preference 100
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
extcommunity soo matches-any
To match any element of a Border Gateway Protocol (BGP) Site-of-Origin (SoO) extended community set, use the extcommunity soo matches-any command in route-policy configuration mode.
extcommunity soo matches-any {extcommunity-set-name | inline-extcommunity-set | parameter}
Syntax Description
extcommunity-set-name |
Name of a SoO extended community set. |
inline-extcommunity-set |
Inline SoO extended community set. The inline extended community set must be enclosed in parentheses. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
|
This command replaced the extcommunity matches-any command. |
Release 3.4.0 |
The parameter argument was added. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the extcommunity soo matches-any command as a conditional expression within an if statement to match elements of an extended community set.
Note For a list of all conditional expressions available within an if statement, see the if command.
A simple condition using the matches-any operator evaluates as true if at least one extended community in the route matches an extended community specification in the named or inline set. If no extended community in the route matches any of the specifications in the named or inline set, then this simple condition evaluates to false. Likewise, when there is no extended community at all in the route, the condition evaluates to false.
Matching an extended community in the route to a specification in a named or an inline set is intuitive. In inline sets, extended community specifications may be parameterized, in which case the relevant matching is done when the value of the parameter has been supplied.
Examples
In the following example, an SoO extended community set named extcomm-soo and a parameterized route policy named my-extcommunity-set-example($tag,$ip) are defined.
The condition route policy named extcommunity soo matches-any is used in an if statement in this policy. If it evaluates to true, the local preference value is set to 100.
If it evaluates to false, the SoO extended community is evaluated using an inline set. If it evaluates to true, the local preference value is set to 200.
If it evaluates to false, the SoO extended community is evaluated using a different inline set. If it evaluates to true, the local preference value is set to 300.
If it evaluates to false, the SoO extended community is evaluated using a different inline set. If it evaluates to true, the local preference value is set to 400.
RP/0/RP0/CPU0:router(config)# extcommunity-set soo extcomm-soo
RP/0/RP0/CPU0:router(config-ext)# 66:60001,
RP/0/RP0/CPU0:router(config-ext)# 77:70001,
RP/0/RP0/CPU0:router(config-ext)# 88:80001,
RP/0/RP0/CPU0:router(config-ext)# 99:90001,
RP/0/RP0/CPU0:router(config-ext)# 100.100.100.1:153
RP/0/RP0/CPU0:router(config-ext)# end-set
RP/0/RP0/CPU0:router(config)# route-policy my-extcommunity-set-example($tag,$ip)
RP/0/RP0/CPU0:router(config-rpl)# if extcommunity soo matches-any extcomm-soo then
RP/0/RP0/CPU0:router(config-rpl-if)# set local-preference 100
RP/0/RP0/CPU0:router(config-rpl-if)# elseif extcommunity soo matches-any (10:20, 10:$tag)
then
RP/0/RP0/CPU0:router(config-rpl-elseif)# set local-preference 200
RP/0/RP0/CPU0:router(config-rpl-elseif)# elseif extcommunity soo matches-any ($ip:$tag)
then
RP/0/RP0/CPU0:router(config-rpl-elseif)# set local-preference 300
RP/0/RP0/CPU0:router(config-rpl-elseif)# elseif extcommunity soo matches-any
(2.3.4.5:$tag) then
RP/0/RP0/CPU0:router(config-rpl-elseif)# set local-preference 400
RP/0/RP0/CPU0:router(config-rpl-elseif)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
Related Commands
extcommunity soo matches-every
To match every element of a Border Gateway Protocol (BGP) Site-of-Origin (SoO) extended community set, use the extcommunity soo matches-every command in route-policy configuration mode.
extcommunity soo matches-every {extcommunity-set-name | inline-extcommunity-set | parameter}
Syntax Description
extcommunity-set-name |
Name of a SoO extended community set. |
inline-extcommunity-set |
Inline SoO extended community set. The inline extended community set must be enclosed in parentheses. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
|
This command replaced the extcommunity matches-every command. |
Release 3.4.0 |
The parameter argument was added. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the extcommunity soo matches-every command as a conditional expression within an if statement to match every element of a SoO extended community set.
Note For a list of all conditional expressions available within an if statement, see the if command.
A simple condition using the matches-every operator evaluates as true if every extended community value in the extended community attribute for the route matches at least one element of the extended community set or inline set. If no extended community in the route matches any of the specifications in the named or inline set, then this simple condition evaluates to false. Likewise, when there is no extended community at all in the route, the condition evaluates to false.
Matching an extended community in the route to a specification in a named or an inline set is intuitive. In inline sets, extended community specifications may be parameterized, in which case the relevant matching is done when the value of the parameter has been supplied.
Examples
In the following example, an extended community set named my-extcomm-rt-set and a parameterized route policy named extcommunity-matches-every-example($as, $tag) are defined. The condition extcommunity soo matches-every is used in an if statement in this policy and if it evaluates to true, the local-preference value is set to 100. If it evaluates to false, the extended community is evaluated using an inline set. If that condition evaluates to true, the local-preference value is set to 200. If it evaluates to false, the local-preference value is set to 300.
RP/0/RP0/CPU0:router(config)# extcommunity-set soo my-extcomm-rt-set
RP/0/RP0/CPU0:router(config-ext)# 10:20,
RP/0/RP0/CPU0:router(config-ext)# 10:30,
RP/0/RP0/CPU0:router(config-ext)# 10:40
RP/0/RP0/CPU0:router(config-ext)# end-set
RP/0/RP0/CPU0:router(config)# route-policy extcommunity-matches-every-example($as, $tag)
RP/0/RP0/CPU0:router(config-rpl)# if extcommunity soo matches-every my-extcomm-rt-set then
RP/0/RP0/CPU0:router(config-rpl-if)# set local-preference 100
RP/0/RP0/CPU0:router(config-rpl-if)# elseif extcommunity soo matches-every (10:20,
10:$tag, $as:30) then
RP/0/RP0/CPU0:router(config-rpl-elseif)# set local-preference 200
RP/0/RP0/CPU0:router(config-rpl-elseif)# else
RP/0/RP0/CPU0:router(config-rpl-elseif)# set local-preference 300
RP/0/RP0/CPU0:router(config-rpl-elseif)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
Related Commands
if
To decide which actions or dispositions should be taken for a given route, use the if command in route-policy configuration mode.
if conditional-expression then action-statement [action-statement] [elseif conditional-expression then action-statement [action-statement]] [else action-statement [action-statement]] endif
Syntax Description
conditional-expression |
Expression to decide which actions or dispositions should be taken for the given route. |
then |
Executes an action statement if the if condition is true. |
elseif |
Strings together a sequence of tests. |
else |
Executes an action statement if the if condition is false. |
endif |
Ends the if statement. |
action-statement |
Sequence of operations that modify a route. |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The if command uses a conditional expression to decide which actions or dispositions should be taken for a given route. Table 1 lists the conditional expressions.
An action statement is a sequence of operations that modify a route, most of which are distinguished by the set keyword. In a route policy, these operations can be grouped. Table 2 lists the action statements.
Table 1 Conditional Expressions
|
|
as-path in |
Matches the AS path of a route to an AS path set. The AS path is a sequence of autonomous system numbers traversed by a route. |
as-path is-local |
Determines if the router (or another router within this autonomous system or confederation) originated the route. |
as-path length |
Performs a conditional check based on the length of the AS path. |
as-path neighbor-is |
Tests the autonomous system number or numbers at the head of the AS path against a sequence of one or more integral values or parameters. |
as-path originates-from |
Tests an AS path against the AS sequence beginning with the AS number that originated a route. |
as-path passes-through |
Tests to learn if the specified integer or parameter appears anywhere in the AS path or if the sequence of integers and parameters appears. |
as-path unique-length |
Performs specific checks based on the length of the AS path. |
community is-empty |
Learns if a route has community attributes associated with it. |
community matches-any |
Matches any element of a community set. |
community matches-every |
Matches every element of a community set. |
destination in |
Matches a destination entry in a named prefix set or inline prefix set. |
extcommunity rt is-empty |
Learns if a route has RT extended community attributes associated with it. |
extcommunity rt matches-any |
Matches elements of an RT extended community set. |
extcommunity rt matches-every |
Matches every element of an RT extended community set. |
extcommunity soo is-empty |
Learns if a route has SoO extended community attributes associated with it. |
extcommunity soo matches-any |
Matches elements of an SoO extended community set. |
extcommunity soo matches-every |
Matches every element of an SoO extended community set. |
local-preference |
Specifies BGP local-preference attribute |
med |
Compares the MED to an integer value or a parameterized value. |
next-hop in |
Compares the next hop associated with the route to data contained in either a named or an inline prefix set. |
orf prefix in |
Matches a prefix in a prefix set or an inline prefix set. |
origin is |
Tests the value of the origin attribute. |
path-type is |
Tests the path type. |
protocol |
Checks if a protocol is installing the route. |
rd in |
Compares the RD associated with the route to data contained in either a named or an inline RD set. |
rib-has-route |
Checks if a route is in the RIB. |
route-has-label |
Checks if a route has a Multiprotocol Label Switching (MPLS) label. |
route-type is |
Compares route types when redistribution is being performed into BGP, OSPF, or IS-IS. |
source in |
Tests the source of the route against the data in either a named or an inline prefix set. |
tag |
Matches a specific tag value. |
vpn-distinguisher is |
Compares the VPN distinguisher against a specified value. |
Table 2 Action Statements
|
|
abort (RPL) |
Discards a route policy definition and returns to global configuration mode. |
add |
Adds an offset to an existing value. |
apply |
Executes a parameterized or an unparameterized policy from within another policy. |
delete community |
Deletes community values from a community list in a route. |
delete extcommunity rt |
Deletes extended community values from an extended community list in a route. |
done |
Accepts this route with no further processing |
drop |
Drops a route. |
end-policy |
Ends the definition of a route policy and exits route-policy configuration mode. |
pass |
Signifies that even though the route has not been modified, the user wants to continue executing in the policy block. |
prepend as-path |
Prepends the AS path with additional autonomous system numbers. |
replace as-path |
Replaces a sequence of AS numbers or private AS numbers in the AS path with the configured local AS. |
set community |
Sets the BGP community attribute. |
set dampening |
Configures BGP route dampening. |
set eigrp-metric |
Sets the Enhanced Interior Gateway Routing Protocol (EIGRP) metric value. |
set extcommunity cost |
Replaces or adds the extended communities for a cost on the route. |
set extcommunity rt |
Replaces or adds the extended communities for an RT on the route. |
set ip-precedence |
Sets the IP precedence to classify packets. |
set isis-metric |
Sets the IS-IS metric attribute value. |
set label |
Sets the BGP label attribute value. |
set level |
Configures the IS-IS level in which redistributed routes should be sent. |
set local-preference |
Specifies a preference value for the autonomous system path. |
set med |
Sets the MED value. |
set metric-type (IS-IS) |
Controls whether IS-IS treats the metric as an internal or external metric. |
set metric-type (OSPF) |
Controls whether OSPF treats the cost as a Type 1 or Type 2 metric. |
set next-hop |
Replaces the next hop associated with a given route. |
set origin |
Changes the origin attribute. |
set ospf-metric |
Sets an OSPF protocol metric attribute value. |
set qos-group |
Sets the QoS group to classify packets. |
set rib-metric |
Sets a RIB metric attribute value for a table policy. |
set rip-metric |
Sets RIP metric attributes. |
set rip-tag |
Sets route tag attribute. |
set tag |
Sets the tag attribute. |
set traffic-index |
Sets the traffic index attribute. |
set weight |
Sets the weight value for BGP routes. |
suppress-route |
Indicates that a given component of an aggregate should be suppressed, that is, not advertised. |
unsuppress-route |
Indicates that a given component of an aggregate should be unsuppressed. |
set vpn-distinguisher |
Sets the VPN distinguisher value. |
Examples
In the following example, any route whose AS path is in the set as-path-set-1 is dropped:
RP/0/RP0/CPU0:router(config-rpl)# if as-path in as-path-set-1 then
RP/0/RP0/CPU0:router(config-rpl-if)# drop
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)#
The contents of the then clause may be an arbitrary sequence of action statements.
The following example shows an if statement with two action statements:
RP/0/RP0/CPU0:router(config-rpl)# if origin is igp then
RP/0/RP0/CPU0:router(config-rpl-if)# set med 42
RP/0/RP0/CPU0:router(config-rpl-if)# prepend as-path 73 5
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)#
The if command also permits an else clause to be executed if the expression is false, as follows:
RP/0/RP0/CPU0:router(config-rpl)# if med eq 200 then
RP/0/RP0/CPU0:router(config-rpl-if)# set community (12:34) additive
RP/0/RP0/CPU0:router(config-rpl-if)# else
RP/0/RP0/CPU0:router(config-rpl-else)# set community (12:56) additive
RP/0/RP0/CPU0:router(config-rpl-else)# endif
RP/0/RP0/CPU0:router(config-rpl)#
The routing policy language (RPL) also provides syntax using the elseif command to string together a sequence of tests, as shown in the following example:
RP/0/RP0/CPU0:router(config-rpl)# if med eq 150 then
RP/0/RP0/CPU0:router(config-rpl-if)# set local-preference 10
RP/0/RP0/CPU0:router(config-rpl-if)# elseif med eq 200 then
RP/0/RP0/CPU0:router(config-rpl-elseif)# set local-preference 60
RP/0/RP0/CPU0:router(config-rpl-elseif)# elseif med eq 250 then
RP/0/RP0/CPU0:router(config-rpl-elseif)# set local-preference 110
RP/0/RP0/CPU0:router(config-rpl-elseif)# else
RP/0/RP0/CPU0:router(config-rpl-else)# set local-preference 0
RP/0/RP0/CPU0:router(config-rpl-else)# endif
RP/0/RP0/CPU0:router(config-rpl)#
The statements within an if statement may themselves be if statements, as shown in this example:
RP/0/RP0/CPU0:router(config-rpl)# if community matches-any (12:34, 56:78) then
RP/0/RP0/CPU0:router(config-rpl-if)# if med eq 150 then
RP/0/RP0/CPU0:router(config-rpl-if)# drop
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl-if)# set local-preference 100
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)#
The policy configuration shown sets the value of the local preference attribute to 100 on any route that has a community value of 12:34 or 56:78 associated with it. However, if any of these routes has a Multi Exit Descriminator (MED) value of 150, then each route with both the community value of 12:34 or 56:78 and a MED of 150 is dropped.
local-preference
To compare the local-preference attribute of a BGP route to an integer value or a parameterized value, use the local-preference command in route-policy configuration mode.
local-preference {eq | is | ge | le} {number | parameter}
Syntax Description
eq | is | ge | le |
Equal to; exact match; greater than or equal to; less than or equal to. |
number |
Value assigned to a 32-bit unsigned integer. Range is 0 to 4294967295. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the local- preference command as a conditional expression within an if statement to compare the local-preference attribute to an integer value or a parameterized value.
Note For a list of all conditional expressions available within an if statement, see the if command.
The MED is a 32-bit unsigned integer. The eq operation compares the local-preference to either a static value or a parameterized value passed to a parameterized policy for equality with that value. A greater than or equal to comparison can also be done with the ge operator, and a less than or equal to comparison can be performed using the le operator.
Examples
The following example shows that if the local-preference is 10, local-preference is set to 100:
RP/0/RP0/CPU0:router(config-rpl)# if local-preference eq 10 then
RP/0/RP0/CPU0:router(config-rpl-if)# set weight 100
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)#
med
To compare the Multi Exit Discriminator (MED) to an integer value or a parameterized value or compare the MED attribute of a BGP route to an integer value, use the med command in route-policy configuration mode.
med {eq | is | ge | le} {number | parameter}
Syntax Description
eq | is | ge | le |
Equal to; exact match; greater than or equal to; less than or equal to. |
number |
Value assigned to a 32-bit unsigned integer. Range is 0 to 4294967295. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the med command as a conditional expression within an if statement to compare the MED to an integer value or a parameterized value.
Note For a list of all conditional expressions available within an if statement, see the if command.
The MED is a 32-bit unsigned integer. The eq operation compares the MED to either a static value or a parameterized value passed to a parameterized policy for equality with that value. A greater than or equal to comparison can also be done with the ge operator, and a less than or equal to comparison can be performed using the le operator.
Examples
The following example shows that if the med commands match, the local preference is set to 100:
RP/0/RP0/CPU0:router(config-rpl)# if med eq 10 then
RP/0/RP0/CPU0:router(config-rpl-if)# set local-preference 100
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)#
next-hop in
To compare the next hop associated with the route to data contained in either an inline or a named prefix set, use the next-hop in command in route-policy configuration mode.
next-hop in {prefix-set-name | inline-prefix-set | parameter}
Syntax Description
prefix-set-name |
Name of a prefix set. |
inline-prefix-set |
Inline prefix set. The inline prefix set must be enclosed in parentheses. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
The parameter argument was added. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the next-hop in command as a conditional expression within an if statement to compare the next hop associated with the route to data contained in either an inline or a named prefix set. The result is true if any value in the prefix set matches the next hop of the route. A comparison that refers to a named prefix set that has no elements in it returns false.
Note For a list of all conditional expressions available within an if statement, see the if command.
The next hop is an IPv4 address entered as a dotted-decimal or an IPv6 address entered as a colon-separated hexadecimal.
Examples
The following example shows that if the next-hop in commands match, the local preference is set to 100
RP/0/RP0/CPU0:router(config-rpl)# if next-hop in some-prefix-set then
RP/0/RP0/CPU0:router(config-rpl-if)# if next-hop in (10.0.0.5, fe80::230/64) then
RP/0/RP0/CPU0:router(config-rpl-if)# set local-preference 0
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)#
orf prefix in
To configure an outbound route filter (ORF), use the orf prefix in command in route-policy configuration mode.
orf prefix in {prefix-set-name | inline-prefix-set}
Syntax Description
prefix-set-name |
Name of a prefix set. |
inline-prefix-set |
Inline prefix set. The inline prefix set must be enclosed in parentheses. |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the orf prefix in command to match a prefix in a prefix set or an inline prefix set.
This command takes either a named prefix set or an inline prefix set value as an argument. It returns true if the destination NLRI matches any entry in the prefix set. An attempt to match destination using a prefix set that is defined but contains no elements returns false.
This command is used in the context of the orf route-policy attach point in BGP. The destination of a route is also known in Border Gateway Protocol (BGP) as its network-layer reachability information (NLRI). It comprises a prefix value and a mask length. The routing policy language (RPL) provides one operation on prefixes, testing them for matching against a list of prefix-match specifications using the in operator.
Examples
In the following example, the prefix set orfpreset1 and the route policy named orfpolicy are defined. Next, the orfpolicy is applied to the neighbor orf attach point.
If the prefix of the route matches any of the prefixes specified in orfpreset1 (211.105.1.0/24, 211.105.5.0/24, 211.105.11.0/24), then the prefix is dropped. If the prefix matches in(211.105.3.0/24, 211.105.7.0/24, 211.105.13.0/24), then the prefix is accepted. In addition to this inbound filtering, BGP sends these prefix entries to the upstream neighbor indicating a permit or deny so that the neighbor can make the same filter updates.
RP/0/RP0/CPU0:router(config)# prefix-set orfpreset1
RP/0/RP0/CPU0:router(config-pfx)# 211.105.1.0/24,
RP/0/RP0/CPU0:router(config-pfx)# 211.105.5.0/24,
RP/0/RP0/CPU0:router(config-pfx)# 211.105.11.0/24
RP/0/RP0/CPU0:router(config-pfx)# end-set
RP/0/RP0/CPU0:router(config)# route-policy orfpolicy
RP/0/RP0/CPU0:router(config-rpl)# if orf prefix in orfpreset1 then
RP/0/RP0/CPU0:router(config-rpl-if)# drop
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)# if orf prefix in (211.105.3.0/24, 211.105.7.0/24,
211.105.13.0/24) then
RP/0/RP0/CPU0:router(config-rpl-if)# pass
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
RP/0/RP0/CPU0:router(config)# router bgp 2
RP/0/RP0/CPU0:router(config-bgp)# neighbor 1.1.1.1
RP/0/RP0/CPU0:router(config-bgp-nbr)# remote-as 3
RP/0/RP0/CPU0:router(config-bgp-nbr)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-bgp-nbr-af)# orf route-policy orfpolicy
Related Commands
|
|
orf |
Specifies BGP ORF and inbound filtering criteria. |
origin is
To match a specific origin type, use the origin is command in route-policy configuration mode.
origin is {igp | egp | incomplete | parameter}
Syntax Description
igp |
Specifies Interior Gateway Protocol. |
egp |
Specifies Exterior Gateway Protocol. |
incomplete |
Specifies that Border Gateway Protocol (BGP) first learned the route by means other than BGP or Interior Gateway Protocol (IGP); for example, the route is learned through configuration. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the origin is command as a conditional expression within an if statement to test the value of the origin attribute.
Note For a list of all conditional expressions available within an if statement, see the if command.
The origin of a BGP route is an enumeration; it is igp, egp, or incomplete.
This command can be parameterized.
Examples
In the following example, the origin is tested within an if statement to learn if it is either igp or egp:
RP/0/RP0/CPU0:router(config-rpl)# if origin is igp or origin is egp then
In the following example, a parameter is used to match a specific origin type:
RP/0/RP0/CPU0:router(config)# route-policy bar($origin)
RP/0/RP0/CPU0:router(config-rpl)# if origin is $origin then
RP/0/RP0/CPU0:router(config-rpl-if)# set med 20
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)#
pass
To pass a route for further processing, use the pass command in route-policy configuration mode.
pass
Syntax Description
This command has no arguments or keywords.
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the pass command to signify that even though this route has not been modified, the user wants to continue executing in this policy block.
Note The pass command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
When a policy block has finished executing, any route that has been modified in this policy block or has received a pass disposition in this policy block passes the policy and execution finishes for that policy. If this policy block is applied from within another policy block and the route is either passed or modified, then execution continues in the policy block that applied this policy block.
Examples
The following example shows how to accept the route unconditionally without modifying it:
RP/0/RP0/CPU0:router(config-rpl)# pass
This example accepts the route unconditionally, without modifying it, if the destination is in prefix-set permitted:
RP/0/RP0/CPU0:router(config-rpl)# if destination in permitted then
RP/0/RP0/CPU0:router(config-rpl-if)# pass
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)#
path-type is
To match path types, use the path-type is command in route-policy configuration mode.
path-type is {ibgp | ebgp | parameter}
Syntax Description
ibgp |
Specifies an internal BGP path. |
ebgp |
Specifies an external BGP path. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.4.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the path-type is command as a conditional expression within an if statement to match path types.
Note For a list of all conditional expressions available within an if statement, see the if command.
Examples
In the following example, if the path is an external BGP path the route is accepted:
RP/0/RP0/CPU0:router(config)# route-policy policy_A
RP/0/RP0/CPU0:router(config-rpl)# if path-type is ebgp then
RP/0/RP0/CPU0:router(config-rpl-if)# pass
RP/0/RP0/CPU0:router(config-rpl-if)# else
RP/0/RP0/CPU0:router(config-rpl-else)# drop
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
policy-global
To define global parameters and enter global parameter configuration mode, use the policy-global command in global configuration mode. To remove global parameters, use the no form of this command.
policy-global
no policy-global
Syntax Description
This command has no arguments or keywords.
Defaults
No default behavior or values
Command Modes
Global configuration
Command History
|
|
Release 3.4.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the policy-global command to define global parameters and enter global parameter configuration mode.
RPL supports the definition of systemwide global parameters that can be used inside a policy definition. The global parameter values can be used directly inside a policy definition similar to the local parameters of parameterized policy. When a parameterized policy has a parameter name "collision" with a global parameter name, parameters local to policy definition take precedence, effectively `masking off' global parameters. In addition, a validation mechanism is in place to prevent the deletion of a particular global parameter if it is referred by any policy. For more information on global parameters and parameterization, see the Implementing Routing Policy on Cisco IOS XR Software module of the Cisco IOS XR Routing Configuration Guide.
Examples
The following example shows how to configure global parameters:
RP/0/RP0/CPU0:router(config)# policy-global
RP/0/RP0/CPU0:router(config-rp-gl)# glbpathtype `ebgp'
RP/0/RP0/CPU0:router(config-rp-gl)# glbtag `100'
RP/0/RP0/CPU0:router(config-rp-gl)# end-global
In the following example, the globalparam argument makes use of the global parameters gbpathtype and glbtag defined above and is defined for a nonparameterized policy:
RP/0/RP0/CPU0:router(config)# route-policy globalparam
RP/0/RP0/CPU0:router(config-rpl)# if path-type is $glbpathtype then
RP/0/RP0/CPU0:router(config-rpl)# set tag $glbtag
RP/0/RP0/CPU0:router(config-rpl)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
Related Commands
|
|
end-global |
Ends the definition of global parameters. |
prefix-set
To enter prefix set configuration mode and define a prefix set, use the prefix-set command in global configuration mode. To remove a named prefix set, use the no form of this command.
prefix-set name
no prefix-set name
Syntax Description
name |
Name of a prefix set. |
Defaults
No default behavior or values
Command Modes
Global configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the prefix-set command to enter prefix set configuration mode and define a prefix set.
A prefix set is a comma-separated list of prefix match specifications. It holds IPv4 or IPv6 prefix match specifications, each of which has four parts: an address, a mask length, a minimum matching length, and a maximum matching length. The address is required, but the other three parts are optional. The address is a standard four-part, dotted-decimal numeric IPv4 address or a colon-separated hexadecimal IPv6 address. The mask length, if present, is a nonnegative decimal integer in the range from 0 to 32 for IPv4 prefixes or 0 to 128 for IPv6 prefixes following the address and separated from it by a slash. The optional minimum matching length follows the address and optional mask length and is expressed as the keyword ge (mnemonic for greater than or equal to), followed by a nonnegative decimal integer in the range from 0 to 32 for IPv4 or 0 to 128 for IPv6. The optional maximum matching length follows the rest and is expressed by the keyword le (mnemonic for less than or equal to), followed by yet another nonnegative decimal integer in the range from 0 to 32 for IPv4 or 0 to 128 for IPv6. A syntactic shortcut for specifying an exact length for prefixes to match is the eq keyword, mnemonic for equal to.
If a prefix match specification has no mask length, then the default mask length is 32 for IPv4 or 128 for IPv6. The default minimum matching length is the mask length. If a minimum matching length is specified, then the default maximum matching length must be less than 32 for IPv4 prefixes or 128 for IPv6 prefixes. Otherwise, if neither a minimum nor maximum length is specified, the default maximum length is the mask length.
Examples
The following example shows a prefix set named legal-ipv4-prefix-examples:
RP/0/RP0/CPU0:router(config)# prefix-set legal-ipv4-prefix-examples
RP/0/RP0/CPU0:router(config-pfx)# 10.0.1.1,
RP/0/RP0/CPU0:router(config-pfx)# 10.0.2.0/24,
RP/0/RP0/CPU0:router(config-pfx)# 10.0.3.0/24 ge 28,
RP/0/RP0/CPU0:router(config-pfx)# 10.0.4.0/24 le 28,
RP/0/RP0/CPU0:router(config-pfx)# 10.0.5.0/24 ge 26 le 30,
RP/0/RP0/CPU0:router(config-pfx)# 10.0.6.0/24 eq 28
RP/0/RP0/CPU0:router(config-pfx)# end-set
The first element of the prefix set matches only one possible value, 10.0.1.1/32 or the host address 10.0.1.1. The second element matches only one possible value, 10.0.2.0/24. The third element matches a range of prefix values, from 10.0.3.0/28 to 10.0.3.255/32. The fourth element matches a range of values, from 10.0.4.0/24 to 10.0.4.240/28. The fifth element matches prefixes in the range from 10.0.5.0/26 to 10.0.5.252/30. The sixth element matches any prefix of length 28 in the range from 10.0.6.0/28 through 10.0.6.240/28.
The following prefix set consists entirely of invalid prefix match specifications:
RP/0/RP0/CPU0:router(config)# prefix-set INVALID-PREFIX-EXAMPLES
RP/0/RP0/CPU0:router(config-pfx)# 10.1.1.1 ge 16,
RP/0/RP0/CPU0:router(config-pfx)# 10.1.2.1 le 16,
RP/0/RP0/CPU0:router(config-pfx)# 10.1.3.0/24 le 23,
RP/0/RP0/CPU0:router(config-pfx)# 10.1.4.0/24 ge 33,
RP/0/RP0/CPU0:router(config-pfx)# 10.1.5.0/25 ge 29 le 28
RP/0/RP0/CPU0:router(config-pfx)# end-set
Neither the minimum length nor the maximum length is legal without a mask length. The maximum length must be at least the mask length. The minimum length must be less than 32, the maximum length of an IPv4 prefix. The maximum length must be equal to or greater than the minimum length.
The following example shows a valid IPv6 prefix set named legal-ipv6-prefix-examples:
RP/0/RP0/CPU0:router(config)# prefix-set legal-ipv6-prefix-examples
RP/0/RP0/CPU0:router(config-pfx)# 2001:0:0:1::/64,
RP/0/RP0/CPU0:router(config-pfx)# 2001:0:0:2::/64,
RP/0/RP0/CPU0:router(config-pfx)# 2001:0:0:3::/64,
RP/0/RP0/CPU0:router(config-pfx)# 2001:0:0:4::/64
RP/0/RP0/CPU0:router(config-pfx)# end-set
prepend as-path
To prepend the AS path with additional autonomous system numbers, use the prepend as-path command in route-policy configuration mode.
prepend as-path {as-number | parameter | most-recent} [number | parameter]
Syntax Description
as-number |
Autonomous system number to prepend to the path. Range for 2-byte numbers is 1 to 65535. Range for 4-byte numbers is 1.0 to 65535.65535. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
most-recent |
Specifies that the most recent autonomous system number should be prepended. |
number |
(Optional) Number of times the autonomous system number should be prepended. Range is 1 to 63. |
Defaults
The default number is 1.
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
The as-number 4-byte number range 1.0 to 65535.65535 was supported. The most-recent keyword was added. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the prepend as-path command to prepend the AS path with additional autonomous system numbers.
Note The prepend as-path command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
This command can take one or two arguments. The first argument (either a number or parameter) is the autonomous system number to prepend to the path. The optional second argument (either a number or parameter) is the number of times the autonomous system number should be prepended.
Examples
The following example shows how to prepend the autonomous system number 666.1 to the AS path three times:
RP/0/RP0/CPU0:router(config-rpl)# prepend as-path 666.1 3
The following example shows how to prepend the autonomous system number 666.0 to the AS path one time:
RP/0/RP0/CPU0:router(config-rpl)# prepend as-path 666.1
protocol
To check the protocol that installs the route, use the protocol command in route-policy configuration mode.
protocol {in (protocol-set) | is protocol-name}
Syntax Description
in (protocol-set) |
Specifies a member of a set. The protocol-set argument accepts the following keywords within parentheses: •bgp—Border Gateway Protocol (BGP) •connected—Connected routes •eigrp—Enhanced Interior Gateway Routing Protocol (EIGRP) •isis—ISO Intermediate System-to-Intermediate System (IS-IS) •ospf—Open Shortest Path First (OSPF) •ospfv3—Open Shortest Path First version 3 (OSPFv3) •rip—Routing Information Protocol (RIP) •static—Static routes Note Keywords must be separated by a comma. |
is protocol-name |
Specifies a single protocol name, and accepted keywords are similar to the protocol-set argument. |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
Support for the ospfv3 keyword was added to the protocol-set argument. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the protocol command as a conditional expression within an if statement to specify a protocol to install a route.
Use the in keyword to determine if a protocol listed in the protocol-set is the originator of the route being filtered.
Use the is keyword to determine if protocol-name is an exact match.
Note For a list of all conditional expressions available within an if statement, see the if command.
Examples
The following example shows how to use the protocol command as a conditional expression within if statements:
RP/0/RP0/CPU0:router(config)# route-policy rip1
RP/0/RP0/CPU0:router(config-rpl)# if protocol in (connected, static) then
RP/0/RP0/CPU0:router(config-rpl-if)# add rip-metric 2
RP/0/RP0/CPU0:router(config-rpl-if)# elseif protocol is bgp 1 then
RP/0/RP0/CPU0:router(config-rpl-elseif)# add rip-metric 3
RP/0/RP0/CPU0:router(config-rpl-elseif)# elseif protocol is ospf 2 then
RP/0/RP0/CPU0:router(config-rpl-elseif)# add rip-metric 4
RP/0/RP0/CPU0:router(config-rpl-elseif)# else
RP/0/RP0/CPU0:router(config-rpl-else)# add rip-metric 5
RP/0/RP0/CPU0:router(config-rpl-else)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
RP/0/RP0/CPU0:router(config)# router rip
RP/0/RP0/CPU0:router(config-rip)# interface GigabitEthernet0/1/0/1
RP/0/RP0/CPU0:router(config-rip-if)# route-policy rip1 out
rd in
To compare the route distinguisher (RD) associated with the route to RDs contained in either a named or an inline RD set, use the rd in command in route-policy configuration mode.
rd in {rd-set-name | inline-rd-set | parameter}
Syntax Description
rd-set-name |
Name of an RD set. |
inline-rd-set |
Inline RD set. The inline RD set must be enclosed in parentheses. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.4.0 |
The parameter argument was added. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the rd in command as a conditional expression within an if statement to match a destination entry in a named prefix set or inline prefix set.
Note For a list of all conditional expressions available within an if statement, see the if command.
This command takes either a named RD set or an inline RD set value as an argument. The condition returns true if the destination entry matches any entry in the RD set or inline RD set. An attempt to match an RD using an RD set that is defined but contains no elements returns false.
Examples
The following example shows the rd in command with an inline RD set value as an argument:
RP/0/RP0/CPU0:router(config)# route-policy
RP/0/RP0/CPU0:router(config-rpl)# if rd in (128.1.0.0/16:100) then
RP/0/RP0/CPU0:router(config-rpl-if)# pass
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
rd-set
To define a route distinguisher (RD) set and enter RD configuration mode, use the rd-set command in global configuration mode.
rd-set name
no rd-set name
Syntax Description
name |
Name of an RD community set. |
Defaults
No default behavior or values
Command Modes
Global configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the rd-set command to create a set with RD elements and enter RD configuration mode. An RD set is a 64-bit value prepended to an IPv4 address to create a globally unique Border Gateway Protocol (BGP) VPN IPv4 address.
Note For m, the mask length is supported.
You can define RD values with the following commands:
•a.b.c.d/m:*—BGP VPN RD in IPv4 format with a wildcard character. For example, 10.0.0.2/24.0:*.
•a.b.c.d/m:n—BGP VPN RD in IPv4 format with a mask. For example, 10.0.0.2/24:666.
•a.b.c.d:* —BGP VPN RD in IPv4 format with a wildcard character. For example, 10.0.0.2:*.
•a.b.c.d:n—BGP VPN RD in IPv4 format. For example, 10.0.0.2:666.
•asn:*—BGP VPN RD in ASN format with a wildcard character. For example, 10002:*.
•asn:n—BGP VPN RD in ASN format. For example, 10002:666.
•x.y:*—BGP VPN RD in 4-byte ASN format with a wildcard character. For example, 10002.101:*.
•x.y:n—BGP VPN RD in 4-byte ASN format. For example, 10002.101:666.
Examples
The following example shows how to create an RD set called my_rd_set:
RP/0/RP0/CPU0:router(config)# rd-set my_rd_set
RP/0/RP0/CPU0:router(config-rd)# 172.16.0.0/16:*,
RP/0/RP0/CPU0:router(config-rd)# 172.17.0.0/16:100,
RP/0/RP0/CPU0:router(config-rd)# 192:*,
RP/0/RP0/CPU0:router(config-rd)# 192:100
RP/0/RP0/CPU0:router(config-rd)# end-set
replace as-path
To replace a sequence of AS numbers or private AS numbers in the AS path with the configured local AS, use the replace as-path command in route-policy configuration mode.
replace as-path {[as-number-list] [parameter] | private-as}
Syntax Description
as-number-list |
(Optional) Sequence of AS numbers to replace. The sequence must be enclosed in single quotes (`'). Range for the 16-byte numbers is from 0 to 65535. |
parameter |
(Optional) Parameter name. The parameter name must be preceded with a "$." |
private-as |
Matches within the BGP private AS range. Range is from 64512 to 65534. |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.4.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the replace as-path command to replace a sequence of AS numbers or private AS numbers in the AS path with the local AS. For example, if the AS path is `67 65534 100 65533 5 78 89 90' and the local AS is 900, then:
would replace `5 78' in the AS path with 900 (from the local AS). The path would be `67 65534 100 65533 900 89 90'.
Consider following statement:
replace as-path private-as
Because 65534 and 65533 are within the private AS range, they are replaced with 900. The path would be `67 900 100 900 5 78 89 90'.
Note The replace as-path command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
Caution
The
replace as-path command changes the AS path content which could lead to routing loops.
Examples
The following example shows how to use the replace as-path command to replace AS numbers in the AS path:
RP/0/RP0/CPU0:router(config-rpl)# replace as-path `90 78 45 $asnum'
RP/0/RP0/CPU0:router(config-rpl)# replace as-path private-as
RP/0/RP0/CPU0:router(config-rpl)# replace as-path `9.9 7.89 14.15 $asnum'
RP/0/RP0/CPU0:router(config-rpl)# replace as-path `9 89 14.15 $asnum'
rib-has-route
To check if a route listed in the prefix set exists in the Routing Information Base (RIB), use the rib-has-route command in route-policy configuration mode.
rib-has-route in {prefix-set-name | inline-prefix-set | parameter}
Syntax Description
prefix-set-name |
Name of a prefix set. |
inline-prefix-set |
Inline prefix set. The inline prefix set must be enclosed in parentheses. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
The name argument was removed. The following arguments were added: •prefix-set-name •inline-prefix-set •parameter |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
If routes are active, then they are advertised. Routes are considered active if they are already installed in the Routing Information Base (RIB).
The prefix sets used in the rib-has-route command contain two match specifications. The first is where an exact route match is requested (for example, 10.10.0.0/16 will match exactly one route) and the second is where a route match or any more-specific route match is allowed (for example, 10.10.0.0/16 le 32 will match the 10.10.0.0/16 route and any longer prefix).
Use the rib-has-route command as a conditional expression within an if statement to check if there is an active route with a specific prefix contained in the RIB. If the statement reveals an active route that meets that criteria, additional actions are executed.
For a list of all conditional expressions available within an if statement, see the if command.
Examples
In the following example, an if statement is used to learn if a route contained in a prefix set 10.10.0.0/16 is in the RIB:
RP/0/RP0/CPU0:router(config-rpl)# if rib-has-route in (10.10.0.0/16 ge 16) then
RP/0/RP0/CPU0:router(config-rpl-if)# pass
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)#
route-has-label
To check if there is a Multiprotocol Label Switching (MPLS) label in a route during redistribution, use the route-has-label command in route-policy configuration mode.
route-has-label
Syntax Description
This command has no arguments or keywords.
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the route-has-label command as a conditional expression within an if statement to check if there is an MPLS label in a route during redistribution.
For a list of all conditional expressions available within an if statement, see the if command.
Examples
In the following example, an if statement learns if an MPLS label is present in a route:
RP/0/RP0/CPU0:router(config-rpl)# if route-has-label then
RP/0/RP0/CPU0:router(config-rpl-if)# pass
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)#
route-policy (RPL)
To define a route policy and enter route-policy configuration mode, use the route-policy command in global configuration mode. To remove a policy definition, use the no form of this command.
route-policy name [(parameter1, parameter2, . . . , parameterN)]
no route-policy name [(parameter1, parameter2, . . . , parameterN)]
Syntax Description
name |
Name of a route policy. |
parameter |
(Optional) Parameter name. The parameter name must be preceded with a "$." The parameters must be enclosed in parenthesis "()". |
Defaults
No default behavior or values
Command Modes
Global configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the route-policy command to define a route policy and enter route-policy configuration mode.
Policy definitions create named bundles of policy statements. A policy definition consists of the route-policy command followed by a name, a group of policy statements, and the end-policy command.
The policy name serves as a handle for binding the policy to protocols.
Examples
The following example shows a simple policy named drop-everything that drops any route it encounters:
RP/0/RP0/CPU0:router(config)# route-policy drop-everything
RP/0/RP0/CPU0:router(config-rpl)# drop
RP/0/RP0/CPU0:router(config-rpl)# end-policy
Policies may also refer to other policies such that common blocks of policy can be reused. This reference to other policies is accomplished by using the apply command. The following is a simple example:
RP/0/RP0/CPU0:router(config)# route-policy drop-as-1234
RP/0/RP0/CPU0:router(config-rpl)# if as-path passes-through '1234' then
RP/0/RP0/CPU0:router(config-rpl-if)# apply check-communities
RP/0/RP0/CPU0:router(config-rpl-if)# else
RP/0/RP0/CPU0:router(config-rpl-else)# pass
RP/0/RP0/CPU0:router(config-rpl-else)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
The apply command indicates that the policy check-communities should be executed if the route under consideration passed through autonomous system 1234 before it was received. If so, the communities of the route are checked, and based on the findings the route may be accepted unmodified, accepted with changes, or dropped.
Related Commands
route-type is
To match route types when redistribution is being performed into Border Gateway Protocol (BGP), Open Shortest Path First (OSPF), or Integrated Intermediate System-to-Intermediate System (IS-IS), use the route-type is command in route-policy configuration mode.
route-type is {local | interarea | internal | type-1 | type-2 | level-l | level-2 | parameter}
Syntax Description
local |
Uses a local value to match locally generated BGP routes. |
interarea |
Uses an interarea value to match IS-IS interarea routes. |
internal |
Uses an internal value to match OSPF intra- and interarea routes. |
type-1 |
Uses a Type 1 value to match Type 1 OSPF routes. |
type-2 |
Uses a Type 2 value to match Type 2 OSPF routes. |
level-1 |
Uses a Level 1 value to match Level 1 IS-IS routes. |
level-2 |
Uses a Level 2 value to match Level 2 IS-IS routes. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
|
The level-1-2 keyword was replaced with the interarea keyword. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the route-type is command as a conditional expression within an if statement to compare route types when redistribution is being performed into BGP, OSPF, or IS-IS.
Note For a list of all conditional expressions available within an if statement, see the if command.
The valid keywords are local, internal, interarea, type-1, type-2, level-1, and level-2. A parameterized value that fills in one of these values may also be used. The local value is used to match locally generated BGP routes. The internal value is used to match OSPF intra- and interarea routes. The type-1 and type-2 values are used to match Type 1 and Type 2 OSPF external routes. The level-1, level-2, and interarea values are used to match IS-IS routes of those respective types.
Because the route type is a matching operator, it appears in conditional clauses of if and then statements.
Examples
In the following example, non-local routes are dropped:
RP/0/RP0/CPU0:router(config)# route-policy policy_A
RP/0/RP0/CPU0:router(config-rpl)# if route-type is local then
RP/0/RP0/CPU0:router(config-rpl-if)# pass
RP/0/RP0/CPU0:router(config-rpl-if)# else
RP/0/RP0/CPU0:router(config-rpl-else)# drop
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
rpl editor
To set the default routing policy language (RPL) editor, use the rpl editor command in global configuration mode.
rpl editor {nano | emacs | vim}
Syntax Description
nano |
Sets the default RPL editor to GNU nano. |
emacs |
Sets the default RPL editor to EMACS. |
vim |
Sets the default RPL editor to VIM. |
Defaults
The Nano editor is the default.
Command Modes
Global configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
The nano keyword was added and the GNU nano text editor became the default editor type. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
In the following example, the default RPL editor is set to Nano:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rpl editor nano
RP/0/RP0/CPU0:router(config)#
In the following example, the default RPL editor is set to EMACS:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rpl editor emacs
RP/0/RP0/CPU0:router(config)#
In the following example, the default RPL editor is set to VIM:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rpl editor vim
RP/0/RP0/CPU0:router(config)#
rpl maximum
To configure system limits on the routing policy subsystem, use the rpl maximum command in global configuration mode.
rpl maximum {{lines | policies} number}
Syntax Description
lines number |
Configures the number of lines of configuration limit. Range is from 1 to 131072. |
policies number |
Configures the number of policies limit. Range is from 1 to 5000. |
Defaults
lines number: 65536
policies numbers: 3500
Command Modes
Global configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the rpl maximum command to configure system limits on the routing policy subsystem. As such, rpl maximum configuration lines do not appear as statements within a routing policy. This command places resource limits on the routing policy subsystem. Use the rpl maximum command to configure the maximum number of lines of configuration and number of policies.
The number of lines of configuration includes the beginning and ending statements, for example, route-policy and end-policy. Each line of configuration for sets is also counted.
A line of configuration is counted only once; it is not counted each time it is used. Similarly, any multiple use of policy in an apply statement counts only as one policy.
A user can change the default values for lines and policies but cannot exceed the maximum value, nor can the value for lines and policies be configured lower than the number of lines or policies that are currently configured.
Examples
In the following example, the maximum number of RPL system limits are modified:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rpl maximum lines 50
RP/0/RP0/CPU0:router(config)# rpl maximum policies 6
Related Commands
|
|
show rpl maximum |
Displays the maximum limits for lines of configuration and number of policies. |
set community
To set the Border Gateway Protocol (BGP) community attributes in a route, use the set community command in route-policy configuration mode.
set community {community-set-name | inline-community-set | parameter} [additive]
Syntax Description
community-set-name |
Community set name. |
inline-community-set |
Inline community set. The inline community set must be enclosed in parentheses. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
additive |
(Optional) Adds communities to communities in the route. |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
The parameter argument was added. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the set community command to set the BGP community attribute.
Note The set community command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
Communities are 32-bit values carried in BGP routes. Each route may have zero or more communities in an unordered list.
Use this command to replace the communities in a route or add to them using the optional additive keyword.
As with the other community forms that support inline sets, either or both 16-bit portions of the community can be parameterized. Likewise, the names of the well-known communities internet (0:0), no-advertise (65535:65281), no-export (65535:65282), and local-AS (65535:65283) can also be used. In an inline community set, each 16-bit portion can also be specified as peeras to express the AS number of the neighbor from which the route was received. If the neighbor AS employs a 4-byte ASN, the IANA-assigned 16-bit value 23456 (AS_TRANS) is used as peeras instead.
Without the additive keyword, any existing communities (other than the well-known communities) are removed and replaced with the given communities. The additive keyword specifies that all communities already present in the route be maintained and the list of communities be added to them.
Examples
The following are incomplete configuration examples using the set community command:
RP/0/RP0/CPU0:router(config-rpl)# set community (10:24)
RP/0/RP0/CPU0:router(config-rpl)# set community (10:24, $as:24, $as:$tag)
RP/0/RP0/CPU0:router(config-rpl)# set community (10:24, internet) additive
RP/0/RP0/CPU0:router(config-rpl)# set community (10:24, $as:24) additive
RP/0/RP0/CPU0:router(config-rpl)# set community (10:24, peeras:24) additive
set dampening
To configure Border Gateway Protocol (BGP) route dampening, use the set dampening command in route-policy configuration mode.
set dampening {halflife {minutes | parameter} | max-suppress {minutes | parameter} | reuse {seconds | parameter} | suppress {penalty-units | parameter} | others default}
Syntax Description
halflife minutes |
Specifies the time (in minutes) after which a penalty is decreased. After the route has been assigned a penalty, the penalty is decreased by half after the half-life period. The process of reducing the penalty happens every 5 seconds. Range is 1 to 45 minutes. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
max-suppress minutes |
Specifies the maximum time (in minutes) a route can be suppressed. Range is 1 to 20000. If the half-life value is allowed to default, the maximum suppress time defaults to 60 minutes. |
reuse seconds |
Unsuppresses a route if the penalty for flapping the route decreases enough to fall below the configured value (in seconds). The process of unsuppressing routes occurs at 10-second increments. Range is 1 to 20000. |
suppress penalty-units |
Specifies a penalty of 1000 each time a route flaps. When a route penalty exceeds the configured limit, it is suppressed. Range is 1 to 20000. |
others default |
If all four keyword values are not specified in the command, then the command must end with others default. This designation indicates that any keyword not defined is set to its default. |
Defaults
half-life: 15 minutes
max-suppress: 60 minutes (four times the half-life)
reuse: 750 seconds
suppress: 2000 penalty units
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
The parameter argument was supported. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The BGP protocol supports route dampening using an exponential backoff algorithm. The algorithm is controlled by setting the four supported BGP values: half-life, max-suppress, reuse, and suppress. Use the set dampening command to configure BGP route dampening.
Note The set dampening command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
A value for at least one of the four keywords must be set. If the set dampening command defines values for three or fewer of the supported keywords, then the configuration must end with the others default, which indicates that any keyword value not defined in the command is set to its default value.
The keywords may appear in the command in any order.
Examples
In the following examples, the half-life is set to 20 minutes and the maximum suppress time is set to
90 minutes. Each command must end with others default because three or fewer keywords are defined.
RP/0/RP0/CPU0:router(config-rpl)# set dampening halflife 20 others default
RP/0/RP0/CPU0:router(config-rpl)# set dampening max-suppress 90 others default
In this example, all four keywords are defined, which means the command does not use others default.
RP/0/RP0/CPU0:router(config-rpl)# set dampening halflife 15 max-suppress 60 reuse 750
suppress 2000
The following command is invalid because it is missing others default.
RP/0/RP0/CPU0:router(config-rpl)# set dampening reuse 700
In the following example, the parameters are used.
RP/0/RP0/CPU0:router(config-rpl)# set dampening halflife $p1 suppress $p4 reuse $p3
max-suppress $p2
set eigrp-metric
To set Enhanced Interior Gateway Routing Protocol (EIGRP) route metrics, use the set eigrp-metric command in route-policy configuration mode.
set eigrp-metric bandwidth delay reliability loading mtu
Syntax Description
bandwidth |
Minimum bandwidth of the route in kilobits per second. Range is 1 to 4294967295. |
delay |
Route delay in tens of microseconds. Delay is 1 or any positive number that is a multiple of 39.1 nanoseconds. Range is 1 to 4294967295. |
reliability |
Likelihood of successful packet transmission expressed as a number between 0 and 255. The value 255 means 100 percent reliability; 0 means no reliability. |
loading |
Effective bandwidth of the route expressed as a number from 1 to 255 (255 is 100 percent loading). |
mtu |
Minimum maximum transmission unit (MTU) size of the route in bytes. Range is from 1 to 65535. |
Defaults
None
Command Modes
Route-policy configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
You can use the add command to further offset an existing EIGRP metric value.
Examples
In the following example, the EIGRP metrics are adjusted for route policy policy_1:
RP/0/RP0/CPU0:router(config)# route-policy policy_1
RP/0/RP0/CPU0:router(config-rpl)# set eigrp-metric 1400 120 250 100 1500
RP/0/RP0/CPU0:router(config-rpl)# end-policy
Related Commands
|
|
add |
Adds an offset to an existing value. |
set extcommunity cost
To set the Border Gateway Protocol (BGP) cost extended community attributes, use the set extcommunity cost command in route-policy configuration mode.
set extcommunity cost {cost-extcommunity-set-name | cost-inline-extcommunity-set | parameter} [additive]
Syntax Description
cost-extcommunity-set-name |
Cost extended community set name. |
cost-inline-extcommunity-set |
Inline cost extended community set. The inline cost extended community set must be enclosed in parentheses. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
additive |
(Optional) Adds extended communities for cost to extended communities in the route. |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
|
This command replaced the set extcommunity command. |
Release 3.4.0 |
The parameter argument was added. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the set extcommunity cost command to either replace the extended communities on the route or add to them using the optional additive keyword. Cost community is an extended community used to tie break the best path selection process in BGP so as to have a localized custom decision for packet forwarding. The extended community format defines generic points of insertion (POI) that influence the decision at different points of the bestpath algorithm.
Note The set extcommunity cost command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
As with the other extended community forms that support inline sets, either or both portions of the community can be parameterized. Similarly to regular communities, the additive keyword can be used to signify adding these extended communities to those that are already present, as opposed to replacing them. Without the additive keyword, any existing extended communities for cost (other than the well-known communities) are removed and replaced with the given communities. The additive keyword specifies that all extended communities for cost already present in the route be maintained and the set of extended communities be added to them. Well-known communities include internet, local-AS, no-advertise, and no-export.
Examples
The following are incomplete configuration examples using the set extcommunity cost command:
RP/0/RP0/CPU0:router(config-rpl)# set extcommunity cost (IGP:10:20)
RP/0/RP0/CPU0:router(config-rpl)# set extcommunity cost (Pre-Bestpath:33:44)
RP/0/RP0/CPU0:router(config-rpl)# set extcommunity cost (IGP:11:21)
set extcommunity rt
To set the Border Gateway Protocol (BGP) route target (RT) extended community attributes, use the set extcommunity rt command in route-policy configuration mode.
set extcommunity rt {rt-extcommunity-set-name | rt-inline-extcommunity-set | parameter} [additive]
Syntax Description
rt-extcommunity-set-name |
Route target extended community set name. |
rt-inline-extcommunity-set |
Inline route target extended community set. The inline route target extended community set must be enclosed in parentheses. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
additive |
(Optional) Adds extended communities for an RT to extended communities in the route. |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
|
This command replaced the set extcommunity command. |
Release 3.4.0 |
The parameter argument was added. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the set extcommunity rt command to either replace the extended communities on the route or add to them using the optional additive keyword.
Note The set extcommunity rt command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
As with the other extended community forms that support inline sets, either or both portions of the community can be parameterized. Similarly to regular communities, the additive keyword can be used to signify adding these extended communities to those that are already present, as opposed to replacing them.
Examples
The following are incomplete configuration examples using the set extcommunity rt command:
RP/0/RP0/CPU0:router(config-rpl)# set extcommunity rt (10:24)
RP/0/RP0/CPU0:router(config-rpl)# set extcommunity rt (10:24, $as:24, $as:$tag)
RP/0/RP0/CPU0:router(config-rpl)# set extcommunity rt (10:24, internet) additive
RP/0/RP0/CPU0:router(config-rpl)# set extcommunity rt (10:24, $as:24) additive
Without the additive keyword, any existing extended communities for cost (other than the well-known communities) are removed and replaced with the given communities. The additive keyword specifies that all extended communities for cost already present in the route be maintained and the list of extended communities be added to them.
set ip-precedence
To set the IP precedence, use the set ip-precedence command in route-policy configuration mode.
set ip-precedence {number | parameter}
Syntax Description
number |
Value of the precedence. The precedence value can be a number from 0 to 7: •7—network (set packets with network control precedence) •6—internet (set packets with internetwork control precedence) •5—critical (set packets with critical precedence) •4—flash-override (set packets with flash override precedence) •3—flash (set packets with flash precedence) •2—immediate (set packets with immediate precedence) •1—priority (set packets with priority precedence) •0—routine (set packets with routine precedence) |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.6.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the set ip-precedence command to set the IP precedence to classify packets. This command is supported at the BGP table-policy attachpoint. Prefixes are marked for subsequent processing in the forwarding plane. After QoS Policy Propagation through Border Gateway Protocol (BGP) (QPPB) is enabled on an interface, corresponding traffic shaping and policing is completed using packet classification based on the IP precedence or QoS group ID. See Cisco IOS XR Modular Quality of Service Configuration Guide for information on QPPB.
Examples
This example shows how use set ip-precedence command:
RP/0/RP0/CPU0:router(config)# route-policy policy_1
RP/0/RP0/CPU0:router(config-rpl)# set ip-precedence 3
RP/0/RP0/CPU0:router(config-rpl)# end-policy
set isis-metric
To set the Intermediate System-to-Intermediate System (IS-IS) metric attribute value, use the set is-is metric command in route-policy configuration mode.
set isis-metric {number | parameter}
Syntax Description
number |
24-bit integer number. Range is from 0 to 16777215. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the set isis-metric command to set the IS-IS metric attribute value for routes that are redistributed into IS-IS.
Examples
In the following example, the IS-IS metric attribute value is set to 1000:
RP/0/RP0/CPU0:router(config)# route-policy policy_1
RP/0/RP0/CPU0:router(config-rpl)# set isis-metric 1000
RP/0/RP0/CPU0:router(config-rpl)# end-policy
set label
To set the Border Gateway Protocol (BGP) label attribute value, use the set label command in route-policy configuration mode.
set label {explicit-null | implicit-null | parameter}
Syntax Description
explicit-null |
Sets the label to the well-known explicit value of 0. |
implicit-null |
Sets the label to the well-known implicit value of 3. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes the proper task IDs. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the set label command in a route policy at the allocate label attachpoint to set the label to explicit-null or implicit-null based on deployment preference. During inter-AS operation, the ASBR sends some of its own loopbacks to other its peers and labels them either implicit null or explicit null.
Examples
The following example shows how to set the labels:
RP/0/RP0/CPU0:router(config)# route-policy labelpolicy
RP/0/RP0/CPU0:router(config-rpl)# if destination in (206.141.1.0/24) then
RP/0/RP0/CPU0:router(config-rpl)# set label explicit-null
RP/0/RP0/CPU0:router(config-rpl)# elseif destination in (206.141.3.0/24) then
RP/0/RP0/CPU0:router(config-rpl)# drop
RP/0/RP0/CPU0:router(config-rpl)# elseif destination in (206.141.4.0/24) then
RP/0/RP0/CPU0:router(config-rpl)# set label explicit-null
RP/0/RP0/CPU0:router(config-rpl)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
set level
To configure the Intermediate System-to-Intermediate System (IS-IS) link-state packet (LSP) level advertised to redistributed routes, use the set level command in route-policy configuration mode.
set level {level-1 | level-2 | level-1-2 | parameter}
Syntax Description
level-1 |
Specifies that redistributed routes are advertised in the Level 1 LSP of the router. |
level-2 |
Specifies that redistributed routes are advertised in the Level 2 LSP of the router. |
level-1-2 |
Specifies that redistributed routes are advertised in Level 1 and Level 2 LSPs of the router. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the IS-IS set level command to configure the LSP level advertised to redistributed routes.
Note The set level command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
This command supports parameterization of the level keyword.
Examples
In the following example, the level is set to Level 2:
RP/0/RP0/CPU0:router(config)# route-policy bgp_isis_redist
RP/0/RP0/CPU0:router(config-rpl)# if destination in (172.2.0.0/16 ge 16) then
RP/0/RP0/CPU0:router(config-rpl)# set level level-2
RP/0/RP0/CPU0:router(config-rpl)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
set local-preference
To set the Border Gateway Protocol (BGP) local preference attribute in a route, use the set local-preference command in route-policy configuration mode.
set local-preference {number | parameter}
Syntax Description
number |
Value assigned to a 32-bit unsigned integer. Range is 0 to 4294967295. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
Default value is 100.
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the set local-preference command to specify a preference value for the autonomous system path. Local preference is a nontransitive (does not cross autonomous system boundaries) attribute and is the second metric considered in the BGP best path calculation (the highest local preference is chosen). Weight is the first metric evaluated for best path, but it is local to the router and propagates only to iBGP peers. See the Implementing BGP on Cisco IOS XR Software module of Cisco IOS XR Routing Configuration Guide for information on the BGP best path calculation.
Note The set local-preference command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
The local preference is a 32-bit unsigned integer.
Examples
In the following example, the local preference value is set to 10:
RP/0/RP0/CPU0:router(config-rpl)# set local-preference 10
set med
To set the Border Gateway Protocol (BGP) Multi Exit Discriminator (MED) attribute, use the set med command in route-policy configuration mode.
set med {number | parameter | igp-cost | {+ | -} {number | parameter} | max-reachable}
Syntax Description
number |
Value assigned to a 32-bit unsigned integer. Range is 0 to 4294967295. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
igp-cost |
Sets the MED value to the cost for the Interior Gateway Protocol (IGP) route to resolve the next hop of the BGP route. |
+ | - |
Sets the MED to the MED plus or minus a static offset. An integer or parameter must follow the plus or minus. |
max-reachable |
Sets the MED value to the maximum possible value of 4294967295. |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the set med command to set the MED value, which is a 32-bit unsigned integer.
Note The set med command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
This command can take the following as argument values: an integer, a parameter, the igp-cost keyword, or a mathematical operator (either plus or minus) followed by an integer or a parameter. Setting the MED to the IGP cost is supported on outbound BGP policies only. The MED cannot be set to the IGP cost in policies applied to other BGP attach points.
The max-reachable keyword sets the MED to the maximum value while leaving the route reachable.
The plus or minus variants allow the user to set the MED to the MED plus or minus a static offset. The variants that allow a user to add or subtract offsets to the MED value are also range checked for underflow or overflow. If the value underflows as a result of subtraction, then the MED value is set to zero. If the value overflows, the value is set to 4294967295, which is the maximum value for MED. when MED is set to 4294967295, the route is unreachable.
Examples
The following two examples show how to set the MED to a value that is either specified directly (using the integer 156) or passed to the policy as a parameter:
RP/0/RP0/CPU0:router(config-rpl)# set med 156
RP/0/RP0/CPU0:router(config-rpl)# set med $med_param
The following example shows how to instruct BGP to automatically set the MED value to the cost of the IGP route that resolves the next hop of the BGP route:
RP/0/RP0/CPU0:router(config-rpl)# set med igp-cost
set metric-type (IS-IS)
To configure the integrated Intermediate System-to-Intermediate System (IS-IS) metric type, use the set metric-type command in route-policy configuration mode.
set metric-type {internal | external | rib-metric-as-internal | rib-metric-as-external | parameter}
Syntax Description
internal |
Sets metric type to internal. |
external |
Sets the metric type to external. |
rib-metric-as-internal |
Uses RIB metric and sets IS-IS internal metric type. |
rib-metric-as-external |
Uses RIB metric and sets IS-IS external metric type. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
The rib-metric-as-internal and rib-metric-as-external keywords were added. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the IS-IS set metric-type command to control whether IS-IS treats the metric as an internal or external metric.
Use the rib-metric-as-external and rib-metric-as-internal keywords to preserve RIB metrics when redistributing routes from another ISIS router instance or another protocol.
Note The set metric-type command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
This command does not support parameterization.
Examples
In the following example, the IS-IS metric type is set to internal:
RP/0/RP0/CPU0:router(config-rpl)# set metric-type internal
set metric-type (OSPF)
To control how Open Shortest Path First (OSPF) computes the cost for a route, use the set metric-type command in route-policy configuration mode.
set metric-type {type-1 | type-2 | parameter}
Syntax Description
type-1 |
Uses the cost set on the route plus the topology-related costs in the calculation for Type 1 metrics. |
type-2 |
Uses only the cost set on the route in the calculation for Type 2 metrics. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the OSPF set metric-type command to control whether OSPF treats the cost as a Type 1 or Type 2 metric.
Note The set metric-type command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
The value of Type 1 or Type 2 controls how OSPF computes the cost for this route. For Type 2 metrics, only the cost set on the route is used. For Type 1 metrics, the cost set on the route plus the topology- related costs are used in the calculation.
This command does not support parameterization.
Examples
In the following example, the OSPF metric type is set to Type 1:
RP/0/RP0/CPU0:router(config-rpl)# set metric-type type-1
set next-hop
To replace the next hop associated with a given route, use the set next-hop command in route-policy configuration mode.
set next-hop {ipv4-address | ipv6-address | peer-address | parameter | self} [destination-vrf]
Syntax Description
ipv4-address |
Valid IPv4 address. |
ipv6-address |
Valid IPv6 address. |
peer-address |
Sets the next hop to the IP address of the remote Border Gateway Protocol (BGP) peer. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
self |
Sets itself as the next hop. |
destination-vrf |
(Optional) Specifies that the next hop of the route should be resolved in destination VRF context. This keyword is available when an IPv4 or IPv6 address or parameter is used. |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
The self keyword was added. |
Release 3.4.0 |
The destination-vrf keyword was added. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the set next-hop command to replace the next hop associated with a specific address.
Note The set next-hop command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
Use the set next-hop peer-address command to set the next hop to the address of the BGP neighbor, where this policy is attached.
The next hop is a valid IPv4 address entered as a dotted decimal or an IPv6 address entered as a colon-separated hexadecimal.
It is not possible to use this command to set the BGP IPv6 link-local next hop.
The destination-vrf keyword is used mainly in Layer 3 VPN networks when importing routes.
Examples
In the following example, the next hop is set to a valid IPv4 address:
RP/0/RP0/CPU0:router(config-rpl)# set next-hop 10.0.0.5
In this example, the next hop is set to a parameter value $nexthop:
RP/0/RP0/CPU0:router(config-rpl)# set next-hop $nexthop
In this example, the next hop is set to a valid IPv4 address with a destination VRF context:
RP/0/RP0/CPU0:router(config-rpl)# set next-hop 10.0.0.5 destination-vrf
set origin
To change the Border Gateway Protocol (BGP) origin attribute, use the set origin command in route-policy configuration mode.
set origin {igp | incomplete | egp | parameter}
Syntax Description
igp |
Sets the origin type to Interior Gateway Protocol (IGP). |
incomplete |
Sets the origin type to incomplete. |
egp |
Sets the origin type to Exterior Gateway Protocol (EGP). |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the set origin command to change the origin attribute.
Note The set origin command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
The origin of a Border Gateway Protocol (BGP) route is igp, egp, or incomplete.
Examples
In the following example, the origin attribute is set to EGP:
RP/0/RP0/CPU0:router(config-rpl)# set origin egp
set ospf-metric
To set an Open Shortest Path First (OSPF) protocol metric attribute value, use the set ospf-metric command in route-policy configuration mode.
set ospf-metric {number | parameter}
Syntax Description
number |
Value assigned to a 24-bit unsigned integer. Range is 0 to 4294967295. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the set ospf-metric command to set the metric for routes that are redistributed into OSPF. The OSPF metric operator accepts either an integer value or a parameter.
Examples
In the following example, the OSPF metric attribute value is set to 1000:
RP/0/RP0/CPU0:router(config)# route-policy policy_1
RP/0/RP0/CPU0:router(config-rpl)# set ospf-metric 1000
RP/0/RP0/CPU0:router(config-rpl)# end-policy
set qos-group
To set the quality of service (QoS) group, use the set qos-group command in route-policy configuration mode:
set qos-group {number | parameter}
Syntax Description
number |
QoS group ID. Range is from 0 to 31. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.6.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the set qos-group command to set the QoS group to classify packets.
This command is supported at the BGP table-policy attachpoint. Prefixes are marked for subsequent processing in the forwarding plane. After QoS Policy Propagation through Border Gateway Protocol (BGP) (QPPB) is enabled on an interface, corresponding traffic shaping and policing is completed using packet classification based on the IP precedence or QoS group ID. See Cisco IOS XR Modular Quality of Service Configuration Guide for information on QPPB.
Examples
This example shows how to use set qos-group command:
RP/0/RP0/CPU0:router(config)# route-policy policy_1
RP/0/RP0/CPU0:router(config-rpl)# set qos-group 12
RP/0/RP0/CPU0:router(config-rpl)# end-policy
set rib-metric
To set the Routing Information Base (RIB) metric attribute value for a table policy, use the set rib-metric command in route-policy configuration mode:
set rib-metric {number | parameter}
Syntax Description
number |
Value assigned to a 32-bit unsigned integer. Range is 0 to 4294967295. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the set rib-metric command set the RIB metric attribute value for BGP routes.
Every route in the RIB has a metric associated with it, signifying the cost to reach a specific destination based on link characteristics. The set rib-metric command modifies the RIB metric while installing BGP routes into RIB, enabling the upgrading or downgrading of the BGP route installed in RIB.
Examples
In the following example, the RIB metric attribute is set to 1000:
RP/0/RP0/CPU0:router(config)# route-policy policy_1
RP/0/RP0/CPU0:router(config-rpl)# set rib-metric 1000
RP/0/RP0/CPU0:router(config-rpl)# end-policy
set rip-metric
To set Routing Information Protocol (RIP) metric attributes, use the set rip-metric command in route-policy configuration mode.
set rip-metric {number | parameter}
Syntax Description
number |
Value assigned to a 4-bit unsigned integer. Range is from 0 to 16. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.4.0 |
The number range of 0 to 15 was changed to 0 to 16. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the set rip-metric command to set the cost attribute for routes that are redistributed into RIP.
You can use the add command to increment the RIP metric value.
Examples
In the following example, the RIP metric number is adjusted for route policy policy_1:
RP/0/RP0/CPU0:router(config)# route-policy policy_1
RP/0/RP0/CPU0:router(config-rpl)# set rip-metric 10
RP/0/RP0/CPU0:router(config-rpl)# end-policy
Related Commands
|
|
add |
Adds an offset to an existing value. |
set rip-tag
To set a route tag attribute for Routing Information Protocol (RIP) routes, use the set rip-tag command in route-policy configuration mode.
set rip-tag {number | parameter}
Syntax Description
number |
Value assigned to a 16-bit unsigned integer. Range is from 0 to 65535. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the set rip-tag command to set the RIP tag attribute for routes that are redistributed into RIP. The RIP tag operator accepts either an integer value or a parameter.
Examples
In the following example, the RIP tag is adjusted for route policy policy_1:
RP/0/RP0/CPU0:router(config)# route-policy policy_1
RP/0/RP0/CPU0:router(config-rpl)# set rip-tag 1000
RP/0/RP0/CPU0:router(config-rpl)# end-policy
set tag
To set the tag attribute, use the set tag command in route-policy configuration mode.
set tag {number | parameter}
Syntax Description
number |
Value assigned to a 32-bit unsigned integer. Range is from 0 to 4294967295. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the set tag command to set the tag attribute.
Note The set tag command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
Tags are routing-protocol independent 32-bit integers that can be associated with a given route in the Routing Information Base (RIB).
For the Border Gateway Protocol (BGP), the tag attribute can be set only at the table-policy attach point.
Examples
In the following example, the tag attribute is set to 10:
RP/0/RP0/CPU0:router(config-rpl)# set tag 10
In this example, the tag attribute is set to a parameter value $tag_param:
RP/0/RP0/CPU0:router(config-rpl)# set tag $tag_param
set rpf-topology
To set reverse-path forwarding (RPF) to any default or nondefault tables for particular sources and groups, use the set rpf-topology command in routing policy configuration mode.
set rpf-topology [vrf vrf-name] [{ipv4 | ipv6} {unicast | multicast | parameter} topology table-name}]
Syntax Description
vrf vrf-name |
[Optional] Specifies a VPN routing and forwarding (VRF) instance. Required when configuring extranet topologies. |
ipv4 |
[Optional] Specifies IPv4 address prefixes. |
ipv6 |
[Optional] Specifies IPv6 address prefixes. |
unicast |
Specifies unicast address prefixes. |
multicast |
Specifies multicast address prefixes. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
topology |
Specifies the default or nondefault topology table for the source or group. |
table-name |
Alphanumeric name string. |
Defaults
Default or current topology setting.
Command Modes
Routing policy configuration
Command History
|
|
Release 3.7.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.8.0 |
This command was supported for MVPN extranet routing configuration. The vrf vrf-name keyword and argument were added. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
When using this command for MVPN extranet routing configuration, only the vrf vrf-name keyword and argument are required.
When using this command in the context of multitopology routing, all keywords and arguments with the exception of vrf vrf-name keyword and argument are required.
Examples
The following example shows how to execute the set rpf-topology command:
RP/0/RP0/CPU0:router# config
RP/0/RP0/CPU0:router(config)# route-policy green
RP/0/RP0/CPU0:router(config-rpl)# set rpf-topology ipv6 multicast topology t12
The following example shows the use of set rpf-topology command in the context of creating an RPF for a topology table in multiple topologies:
if destination in (225.0.0.1, 225.0.0.11) then
set rpf-topology ipv4 multicast topology t201
elseif destination in (225.0.0.2, 225.0.0.12) then
set rpf-topology ipv4 multicast topology t202
elseif destination in (225.0.0.3, 225.0.0.13) then
if destination in (225.0.0.8) then
set rpf-topology ipv4 multicast topology t208
elseif destination in (225.0.0.9) then
set rpf-topology ipv4 multicast topology t209
elseif destination in (225.0.0.10) then
set rpf-topology ipv4 multicast topology t210
Related Commands
|
|
rpf topology |
Assigns a route policy in PIM to select a reverse-path forwarding (RPF) topology. |
set traffic-index
To set the traffic index attribute, use the set traffic-index command in route-policy configuration mode.
set traffic-index {number | parameter | ignore}
Syntax Description
number |
Integer value assigned to the traffic index attribute. Range is 1 to 63. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
ignore |
Specifies that Border Gateway Protocol (BGP) policy accounting is not done. |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the set traffic-index command to set the traffic index attribute.
Note The set traffic-index command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
Traffic index is a special attribute for BGP. It is used as an index to a set of counters that are maintained by forwarding hardware. It is also used to track packet and byte counters that are forwarded using routes with specific attributes. These counters can be enabled and disabled on an individual interface basis.
The traffic index attribute can be set only at the table-policy attach point, and can take a value from 1 to 63, or a value of ignore. If the traffic index is set to ignore, then BGP policy accounting is not done. Parameterization of this value is also supported.
Examples
In the following example, a policy is created in which the traffic index is set to 10 for all routes that originated in autonomous system 1234:
RP/0/RP0/CPU0:router(config)# route-policy count-as-1234
RP/0/RP0/CPU0:router(config-rpl)# if as-path originates-from `1234' then
RP/0/RP0/CPU0:router(config-rpl-if)# set traffic-index 10
RP/0/RP0/CPU0:router(config-rpl-if)# else
RP/0/RP0/CPU0:router(config-rpl-if)# pass
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
This policy could then be attached using the BGP table-policy command. The counters could then be enabled on various interfaces with the appropriate commands.
set vpn-distinguisher
To change the Border Gateway Protocol (BGP) VPN distinguisher attribute, use the set vpn-distinguisher command in route-policy configuration mode.
set vpn-distinguisher {number | parameter}
Syntax Description
number |
Value assigned to a 32-bit unsigned integer. Range is from 1 to 4294967295. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.4.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the set vpn-distinguisher command to change the VPN distinguisher attribute.
Note The set origin command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
A VPN distinguisher is used in Layer 3 VPN networks for enhanced individual VPN control and to avoid route target mapping at AS boundaries in inter-AS VPN networks. Route target extended communities are removed at neighbor outbound, and the VPN distinguisher value is applied on the BGP route as an extended community. When the route is received on a neighboring router in another AS, the VPN distinguisher is removed and mapped to a route target extended community.
Examples
In the following example, the VPN distinguisher attribute is set to 456:
RP/0/RP0/CPU0:router(config-rpl)# set vpn-distinguisher 456
set weight
To set the weight value for Border Gateway Protocol (BGP) routes, use the set weight command in route-policy configuration mode.
set weight {number | parameter}
Syntax Description
number |
Number assigned to the weight value for BGP routes. Weight is 16 bits. Range is 0 to 65535. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the set weight command to set the weight value for BGP routes.
Note The set weight command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
A weight is a value that can be applied to a route to override the BGP local preference. This is not a BGP attribute announced to BGP peer routers. RPL can be used to set the weight value.
Given two BGP routes with the same network layer reachability information (NLRI), a route with a higher weight is selected, no matter what the values of other BGP attributes may be. However, weight only has significance on the local router. It is not sent from one BGP speaker to another, even within the same autonomous system.
On Cisco routers, if a BGP route is sourced by the local router, its weight is automatically set to 32768; if the BGP route is learned from another router, its weight is automatically set to 0. Thus, by default, locally sourced routes are preferred over BGP learned routes.
Examples
In the following example, the weight of the route is set to 10 and then to a parameter value $weight_param:
RP/0/RP0/CPU0:router(config-rpl)# set weight 10
RP/0/RP0/CPU0:router(config-rpl)# set weight $weight_param
show rpl
To display system-wide RPL configuration, use the show rpl command in EXEC mode.
show [running-config] rpl [maximum {lines configuration-limit | policies policies-limit} | editor {emacs | nano | vim}]
Syntax Description
running-config |
(Optional) Displays configuration-limit argument. |
maximum |
(Optional) Displays the maximum number of lines of configuration and number of policies. |
lines configuration-limit |
(Optional) Displays the number of lines to which configuration is limited. Range is 1 to 131072. The configuration-limit argument is available if the running-config keyword is specified. |
policies policies-limit |
(Optional) Displays the limit on the number of policies. Range is 1 to 5000. The configuration-limit argument is available if the running-config keyword is specified. |
editor |
(Optional) Specifies the default RPL editor. This keyword is available if the running-config keyword is specified. |
emacs |
(Optional) Displays the default RPL editor to Micro Emacs. |
nano |
(Optional) Displays the default RPL editor to nano. |
vim |
(Optional) Displays the default RPL editor to Vim. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following shows the output of the show running-config rpl command:
RP/0/RP0/CPU0:router# show running-config rpl
extcommunity-set rt ext_comm_set_rt_ex1
prefix-set prefix_set_ex1
if destination in prefix_set_ex1 then
if (community matches-any com_set_exl) then
set community (10:666) additive
if (extcommunity rt matches-any ext_comm_set_rt_ex1) then
set community (10:999) additive
Related Commands
|
|
show rpl maximum |
Displays the maximum limits for lines of configuration and number of policies. |
show rpl active as-path-set
To display the AS path sets that are referenced by at least one policy that is being used at an attach point, use the show rpl active as-path-set command in EXEC mode.
show rpl active as-path-set [detail]
Syntax Description
detail |
(Optional) Displays the content of the object and all referenced objects for active AS path sets. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
Added the detail keyword. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl active as-path-set command to display all AS path sets that are in use in the system and referenced either directly or indirectly at a policy attach point.
Examples
This example shows the following sample configuration:
address-family ipv4 unicast
address-family ipv4 unicast
address-family ipv4 unicast
RP/0/RP0/CPU0:router# show rpl route-policy policy_2 detail
prefix-set prefix_set_ex1
community-set comm_set_ex1
extcommunity-set rt ext_comm_set_rt_ex1
if destination in prefix_set_ex1 then
if (community matches-any comm_set_ex1) then
set community (10:666) additive
if (extcommunity rt matches-any ext_comm_set_rt_ex1) then
set community (10:999) additive
RP/0/RP0/CPU0:router# show rpl route-policy policy_1 detail
prefix-set prefix_set_ex1
as-path-set as_path_set_ex1
if (destination in prefix_set_ex1) then
if (as-path in as_path_set_ex1) then
set community (10:333) additive
Given this sample configuration, the show rpl active as-path-set command displays the following information:
RP/0/RP0/CPU0:router# show rpl active as-path-set
ACTIVE -- Referenced by at least one policy which is attached
INACTIVE -- Only referenced by policies which are not attached
UNUSED -- Not attached (directly or indirectly) and not referenced
The following as-path-sets are ACTIVE
-------------------------------------
Related Commands
show rpl active community-set
To display the community sets that are referenced by at least one policy that is being used at an attach point, use the show rpl active community-set command in EXEC mode.
show rpl active community-set [detail]
Syntax Description
detail |
(Optional) Displays the content of the object and all referenced objects for active community sets. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
Added the detail keyword. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl active community-set command to display all community sets that are in use in the system and referenced either directly or indirectly at a policy attach point.
Examples
This example shows the following sample configuration:
address-family ipv4 unicast
address-family ipv4 unicast
address-family ipv4 unicast
RP/0/RP0/CPU0:router# show rpl route-policy policy_2 detail
prefix-set prefix_set_ex1
community-set comm_set_ex1
extcommunity-set rt ext_comm_set_rt_ex1
if destination in prefix_set_ex1 then
if (community matches-any comm_set_ex1) then
set community (10:666) additive
if (extcommunity rt matches-any ext_comm_set_rt_ex1) then
set community (10:999) additive
RP/0/RP0/CPU0:router# show rpl route-policy policy_1 detail
prefix-set prefix_set_ex1
as-path-set as_path_set_ex1
if (destination in prefix_set_ex1) then
if (as-path in as_path_set_ex1) then
set community (10:333) additive
Given this sample configuration, the show rpl active community-set command displays the following information:
RP/0/RP0/CPU0:router# show rpl active community-set
ACTIVE -- Referenced by at least one policy which is attached
INACTIVE -- Only referenced by policies which are not attached
UNUSED -- Not attached (directly or indirectly) and not referenced
The following community-sets are ACTIVE
---------------------------------------
Related Commands
|
|
show rpl active as-path-set |
Displays the AS path sets that are referenced by at least one policy that is being used at an attach point. |
show rpl active extcommunity-set |
Displays the extended community sets that are referenced by at least one policy that is being used at an attach point. |
show rpl active prefix-set |
Displays the route policies that are referenced by at least one policy that is being used at an attach point. |
show rpl active prefix-set |
Displays the prefix sets that are referenced by at least one policy that is being used at an attach point. |
show rpl active rd-set |
Displays the route distinguisher sets that are referenced by at least one policy that is being used at an attach point. |
show rpl active extcommunity-set
To display the extended community sets for cost, route target (RT), and Site-of-Origin (SoO) that are referenced by at least one route policy used at an attach point, use the show rpl active extcommunity-set command in EXEC mode.
show rpl active extcommunity-set [cost | rt | soo] [detail]
Syntax Description
cost |
(Optional) Displays all extended community cost sets. |
rt |
(Optional) Displays all extended community RT sets. |
soo |
(Optional) Displays all extended community SoO sets. |
detail |
(Optional) Displays the content of the object and all referenced objects for active extended community sets. |
Defaults
All extended community sets are displayed.
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
Added the cost, rt, soo, and detail keywords. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl active extcommunity-set command to display all extended community sets that are in use in the system and referenced either directly or indirectly at a policy attach point.
Examples
This example shows the following sample configuration:
address-family ipv4 unicast
address-family ipv4 unicast
address-family ipv4 unicast
RP/0/RP0/CPU0:router# show rpl route-policy policy_2 detail
prefix-set prefix_set_ex1
community-set comm_set_ex1
extcommunity-set rt ext_comm_set_rt_ex1
if destination in prefix_set_ex1 then
if (community matches-any comm_set_ex1) then
set community (10:666) additive
if (extcommunity rt matches-any ext_comm_set_rt_ex1) then
set community (10:999) additive
RP/0/RP0/CPU0:router# show rpl route-policy policy_1 detail
prefix-set prefix_set_ex1
as-path-set as_path_set_ex1
if (destination in prefix_set_ex1) then
if (as-path in as_path_set_ex1) then
set community (10:333) additive
Given this sample configuration, the show rpl active extcommunity-set command displays the following information:
RP/0/RP0/CPU0:router# show rpl active extcommunity-set
ACTIVE -- Referenced by at least one policy which is attached
INACTIVE -- Only referenced by policies which are not attached
UNUSED -- Not attached (directly or indirectly) and not referenced
The following extcommunity-sets are ACTIVE
------------------------------------------
Related Commands
|
|
show rpl active as-path-set |
Displays the AS path sets that are referenced by at least one policy that is being used at an attach point. |
show rpl active community-set |
Displays the community sets that are referenced by at least one policy that is being used at an attach point. |
show rpl active prefix-set |
Displays the route policies that are referenced by at least one policy that is being used at an attach point. |
show rpl active prefix-set |
Displays the prefix sets that are referenced by at least one policy that is being used at an attach point. |
show rpl active rd-set |
Displays the route distinguisher sets that are referenced by at least one policy that is being used at an attach point. |
show rpl active prefix-set
To display the prefix sets that are referenced by at least one policy that is being used at an attach point, use the show rpl active prefix-set command in EXEC mode.
show rpl active prefix-set [detail]
Syntax Description
detail |
(Optional) Displays the content of the object and all referenced objects for active prefix sets. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
Added the detail keyword. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl active prefix-set command to display all prefix sets that are in use in the system and referenced either directly or indirectly at a policy attach point.
Examples
This example shows the following sample configuration:
address-family ipv4 unicast
address-family ipv4 unicast
address-family ipv4 unicast
RP/0/RP0/CPU0:router# show rpl route-policy policy_2 detail
prefix-set prefix_set_ex1
community-set comm_set_ex1
extcommunity-set rt ext_comm_set_rt_ex1
if destination in prefix_set_ex1 then
if (community matches-any comm_set_ex1) then
set community (10:666) additive
if (extcommunity rt matches-any ext_comm_set_rt_ex1) then
set community (10:999) additive
RP/0/RP0/CPU0:router# show rpl route-policy policy_1 detail
prefix-set prefix_set_ex1
as-path-set as_path_set_ex1
if (destination in prefix_set_ex1) then
if (as-path in as_path_set_ex1) then
set community (10:333) additive
The following example displays active prefix sets:
RP/0/RP0/CPU0:router# show rpl active prefix-set
ACTIVE -- Referenced by at least one policy which is attached
INACTIVE -- Only referenced by policies which are not attached
UNUSED -- Not attached (directly or indirectly) and not referenced
The following prefix-sets are ACTIVE
------------------------------------
Related Commands
|
|
show rpl active as-path-set |
Displays the AS path sets that are referenced by at least one policy that is being used at an attach point. |
show rpl active community-set |
Displays the community sets that are referenced by at least one policy that is being used at an attach point. |
show rpl active extcommunity-set |
Displays the extended community sets that are referenced by at least one policy that is being used at an attach point. |
show rpl active prefix-set |
Displays the route policies that are referenced by at least one policy that is being used at an attach point. |
show rpl active rd-set |
Displays the route distinguisher sets that are referenced by at least one policy that is being used at an attach point. |
show rpl active rd-set
To display the route distinguisher (RD) sets that are referenced by at least one policy that is being used at an attach point, use the show rpl active rd-set command in EXEC mode.
show rpl active rd-set [detail]
Syntax Description
detail |
(Optional) Displays the content of the object and all referenced objects for active route policies. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 3.6.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl active rd-set command to display all RD sets that are in use in the system and that are referenced either directly or indirectly at a policy attach point.
Examples
This example shows the following sample configuration:
address-family vpnv4 unicast
address-family ipv4 unicast
route-policy rdsetmatch in
Given this sample configuration, the show rpl active rd-set command displays the following information:
RP/0/RP0/CPU0:router# show rpl active rd-set
ACTIVE -- Referenced by at least one policy which is attached INACTIVE -- Only referenced
by policies which are not attached UNUSED -- Not attached (directly or indirectly) and not
referenced
The following rd-sets are ACTIVE
------------------------------------------
Related Commands
show rpl active route-policy
To display the route policies that are referenced by at least one policy that is being used at an attach point, use the show rpl active route-policy command in EXEC mode.
show rpl active route-policy [detail]
Syntax Description
detail |
(Optional) Displays the content of the object and all referenced objects for active route policies. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The policy keyword was changed to route-policy. |
Release 3.3.0 |
Added the detail keyword. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl active route-policy command to display all policies that are in use in the system and that are referenced either directly or indirectly at a policy attach point.
Examples
This example shows the following sample configuration:
address-family ipv4 unicast
address-family ipv4 unicast
address-family ipv4 unicast
RP/0/RP0/CPU0:router# show rpl route-policy policy_1
if (destination in prefix_set_ex1) then
if (as-path in as_path_set_ex1) then
set community (10:333) additive
RP/0/RP0/CPU0:router# show rpl route-policy policy_2
if destination in prefix_set_ex1 then
if (community matches-any comm_set_ex1) then
set community (10:666) additive
if (extcommunity rt matches-any ext_comm_set_rt_ex1) then
set community (10:999) additive
Given this sample configuration, the show rpl active route-policy command displays the following information:
RP/0/RP0/CPU0:router# show rpl active route-policy
ACTIVE -- Referenced by at least one policy which is attached
INACTIVE -- Only referenced by policies which are not attached
UNUSED -- Not attached (directly or indirectly) and not referenced
The following policies are (ACTIVE)
-----------------------------------
Related Commands
|
|
show rpl active as-path-set |
Displays the AS path sets that are referenced by at least one policy that is being used at an attach point. |
show rpl active community-set |
Displays the community sets that are referenced by at least one policy that is being used at an attach point. |
show rpl active extcommunity-set |
Displays the extended community sets that are referenced by at least one policy that is being used at an attach point. |
show rpl active prefix-set |
Displays the prefix sets that are referenced by at least one policy that is being used at an attach point. |
show rpl active rd-set |
Displays the route distinguisher sets that are referenced by at least one policy that is being used at an attach point. |
show rpl as-path-set
To display the contents of AS path sets, use the show rpl as-path-set command in EXEC mode.
show rpl as-path-set [name | states | brief]
Syntax Description
name |
(Optional) Name of the AS path set. |
states |
(Optional) Displays all unused, inactive, and active states. |
brief |
(Optional) Limits the display to a list of the names of all AS path sets without their configurations. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The summary keyword was replaced with brief. The * keyword was removed and the states keyword was added. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the optional brief keyword to limit the display to a list of the names of all AS path sets without their configurations.
Examples
This example shows the following sample configuration:
RP/0/RP0/CPU0:router# show rpl route-policy policy_1
if (destination in prefix_set_ex1) then
if (as-path in as_path_set_ex1) then
set community (10:333) additive
Given this sample configuration, the show rpl as-path-set as_path_set_ex1 command displays the following information:
RP/0/RP0/CPU0:router# show rpl as-path-set as_path_set_ex1
as-path-set as_path_set_ex1
Related Commands
show rpl as-path-set attachpoints
To display all of the policies used at an attach point that reference the named AS path set, use the show rpl as-path-set attachpoints command in EXEC mode.
show rpl as-path-set name attachpoints
Syntax Description
name |
Name of an AS path set. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl as-path-set attachpoints command to display all policies used at an attach point that reference the named set either directly or indirectly.
The AS path set name is required.
Examples
This example shows the following sample configuration:
address-family ipv4 unicast
address-family ipv4 unicast
address-family ipv4 unicast
RP/0/RP0/CPU0:router# show rpl route-policy policy_1
if (destination in prefix_set_ex1) then
if (as-path in as_path_set_ex1) then
set community (10:333) additive
RP/0/RP0/CPU0:router# show rpl route-policy policy_2
if (destination in prefix_set_ex1) then
if (community matches-any comm_set_ex1) then
set community (10:666) additive
if (extcommunity matches-any ext_comm_set_rt_ex1) then
set community (10:999) additive
Given this sample configuration, the show rpl as-path-set as_path_set_ex1 attachpoints command displays the following information:
RP/0/RP0/CPU0:router# show rpl as-path-set as_path_set_ex1 attachpoints
Neighbor/Group type afi/safi in/out referring policy attached policy
----------------------------------------------------------------------------
10.0.101.2 -- IPv4/uni in policy_1 policy_1
10.0.101.3 -- IPv4/uni in policy_2 policy_2
Table 3 describes the significant fields shown in the display.
Table 3 show rpl as-path-set attachpoints Field Descriptions
|
|
BGP Attachpoint |
Location of the attach point. |
Neighbor/Group |
IP address of the attach point on the neighbor. |
type |
Displays the address family mode. |
afi/safi |
Address family identifier or subsequent address family identifier. |
in/out |
Import or export policy. |
referring policy |
Policy that refers to the AS path set. |
attached policy |
Policy used at the attach point. |
Related Commands
show rpl as-path-set references
To list all of the policies that reference the named AS path set, use the show rpl as-path-set references command in EXEC mode.
show rpl as-path-set name references [brief]
Syntax Description
name |
Name of the prefix set. |
brief |
(Optional) Limits the output to just the brief table and not the detailed information for the named AS path set. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The summary keyword was replaced with brief. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl as-path-set references command to display all policies that reference the named AS path set either directly or indirectly.
Use the optional brief keyword to limit the output to just a summary table and not the detailed information for the AS path set.
Examples
This example shows the following sample configuration:
address-family ipv4 unicast
address-family ipv4 unicast
RP/0/RP0/CPU0:router# show rpl route-policy policy_1
if (destination in prefix_set_ex1) then
if (as-path in as_path_set_ex1) then
set community (10:333) additive
Given this sample configuration, the show rpl as-path-set as_path_set_ex1 references command displays the following information:
RP/0/RP0/CPU0:router# show rpl as-path-set as_path_set_ex1 references
Usage Direct -- Reference occurs in this policy
Usage Indirect -- Reference occurs via an apply statement
Status UNUSED -- Policy is not in use at an attachpoint (unattached)
Status ACTIVE -- Policy is actively used at an attachpoint
Status INACTIVE -- Policy is applied by an unattached policy
--------------------------------------------------------------
route-policy usage policy status
--------------------------------------------------------------
Table 4 describes the significant fields shown in the display.
Table 4 show rpl as-path-set references Field Descriptions
|
|
Usage/Status |
Displays the usage and status of all policies that reference the AS path set. Values for usage are Direct or Indirect. Values for policy status are ACTIVE, INACTIVE, or UNUSED. |
count |
Number of policies that match each usage and status option. |
route-policy |
Name of the route policies that reference the AS path set. |
usage |
Type of usage for the policy. |
policy status |
Status of the policy. |
Related Commands
show rpl community-set
To display the configuration of community sets, use the show rpl community-set command in EXEC mode.
show rpl community-set [name | states | brief]
Syntax Description
name |
(Optional) Name of the community set. |
states |
(Optional) Shows all unused, inactive, and active states. |
brief |
(Optional) Limits the display to a list of the names of all community sets without their configurations. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The summary keyword was replaced with brief. The * keyword was removed and the states keyword was added. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the optional brief keyword to limit the display to a list of the names of community sets without their configurations.
Examples
This example shows the following sample configuration:
if (destination in prefix_set_ex2) then
if (community matches-any comm_set_ex2) then
set community (10:666) additive
if (extcommunity matches-any ext_comm_set_rt_ex2) then
set community (10:999) additive
Given this sample configuration, the show rpl community-set comm_set_ex2 command displays the following information:
RP/0/RP0/CPU0:router# show rpl community-set comm_set_ex2
community-set comm_set_ex2
Related Commands
show rpl community-set attachpoints
To display all the policies used at an attach point that reference the named community set, use the show rpl community-set attachpoints command in EXEC mode.
show rpl community-set name attachpoints
Syntax Description
name |
Name of a community set. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl community-set attachpoints command to display all the policies used at an attach point that reference the named community set either directly or indirectly.
The community set name is required.
Examples
This example shows the following sample configuration:
address-family ipv4 unicast
address-family ipv4 unicast
if destination in prefix_set_ex1 then
if (community matches-any comm_set_ex1) then
set community (10:666) additive
if (extcommunity rt matches-any ext_comm_set_rt_ex1) then <<<<<
set community (10:999) additive
Given this sample configuration, the show rpl community-set attachpoints command displays the following information:
RP/0/RP0/CPU0:router# show rpl community-set ext_comm_set_rt_ex1 attachpoints
Neighbor/Group type afi/safi in/out referring policy attached policy
----------------------------------------------------------------------------
10.0.101.3 -- IPv4/uni in policy_2 policy_2
Table 5 describes the significant fields shown in the display.
Table 5 show rpl community-set attachpoints Field Descriptions
|
|
BGP Attachpoint |
Location of the attach point. |
Neighbor/Group |
IP address of the attach point on the neighbor. |
type |
Displays the address family mode. |
afi/safi |
Address family identifier or subsequent address family identifier. |
in/out |
Import or export policy. |
referring policy |
Policy that refers to the AS path set. |
attached policy |
Policy used at the attach point. |
Related Commands
show rpl community-set references
To list all the policies that reference the named community set, use the show rpl community-set references command in EXEC mode.
show rpl community-set name references [brief]
Syntax Description
name |
Name of a community set. |
brief |
(Optional) Limits the output to just the summary table and not the detailed information for the community set. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The summary keyword was replaced with brief. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl community-set references command to display all the policies that reference the named community set.
Use the optional brief keyword to limit the output to just a summary table and not the detailed information for the community set.
Examples
This example shows the following sample configuration:
address-family ipv4 unicast
address-family ipv4 unicast
if (destination in prefix_set_ex1) then
if (community matches-any comm_set_ex1) then
set community (10:666) additive
if (extcommunity matches-any ext_comm_set_rt_ex1) then
set community (10:999) additive
Given this sample configuration, the show rpl extcommunity-set comm_set_ex1 references command displays the following information:
RP/0/RP0/CPU0:router# show rpl extcommunity-set comm_set_ex1 references
Usage Direct -- Reference occurs in this policy
Usage Indirect -- Reference occurs via an apply statement
Status UNUSED -- Policy is not in use at an attachpoint (unattached)
Status ACTIVE -- Policy is actively used at an attachpoint
Status INACTIVE -- Policy is applied by an unattached policy
--------------------------------------------------------------
route-policy usage policy status
--------------------------------------------------------------
Table 6 describes the significant fields shown in the display.
Table 6 show rpl community-set references Field Descriptions
|
|
Usage/Status |
Displays the usage and status of all policies that reference the community set. Values for usage are Direct or Indirect. Values for status are ACTIVE, INACTIVE, and UNUSED. |
count |
Number of policies that match each usage and status option. |
route-policy |
Name of the route policies that reference the community set. |
usage |
Type of usage for the policy. |
policy status |
Status of the policy. |
Related Commands
show rpl extcommunity-set
To display the configuration of extended community sets, use the show rpl extcommunity-set command in EXEC mode.
show rpl extcommunity-set [name [attachpoints | references]] [cost | rt | soo] [name] [brief] [states]
Syntax Description
name |
(Optional) Name of the community set. |
attachpoints |
(Optional) Displays all attach points for this community set. |
references |
(Optional) Displays all policies that use this community set. |
cost |
(Optional) Displays all extended community cost sets. |
rt |
(Optional) Displays all extended community RT sets. |
soo |
(Optional) Displays all extended community SoO sets. |
brief |
(Optional) Limits the display to a list of the names of all extended community sets without their configurations. |
states |
(Optional) Displays all unused, inactive, and active states. |
Defaults
If an attachpoint or reference is not specified, all configured extended community sets are displayed
If a cost, RT, or SoO sets is not specified, all configured extended community sets are displayed
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The summary keyword was replaced with brief. The * keyword was removed and the states keyword was added. |
Release 3.3.0 |
The following keywords were added: attachpoints, references, cost, rt, and soo. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the optional brief keyword to limit the display to a list of the names of extended community sets without their configurations.
Examples
In the following example, the configuration of an extended community is displayed for the RT community set named ext_comm_set_rt_ex1:
RP/0/RP0/CPU0:router# show rpl extcommunity-set rt ext_comm_set_rt_ex1
In the following example, the configuration of an extended community is displayed with all RT set objects:
RP/0/RP0/CPU0:router# show rpl extcommunity-set rt
Listing for all Extended Community RT Set objects
extcommunity-set rt extrt1
extcommunity-set rt rtset1
extcommunity-set rt rtset3
extcommunity-set rt extsoo1
extcommunity-set rt rtsetl1
In the following example, the configuration of an extended community is displayed with all cost set objects:
RP/0/RP0/CPU0:router# show rpl extcommunity-set cost
Listing for all Extended Community COST Set objects
extcommunity-set cost costset1
extcommunity-set cost costset2
In the following example, the configuration of an extended community is displayed with all SoO set objects:
Extended Community SOO Set objects
extcommunity-set soo sooset1
extcommunity-set soo sooset3
Related Commands
show rpl inactive as-path-set
To display the AS path sets that are referenced by a policy but not in any policy that is used at an attach point, use the show rpl inactive as-path-set command in EXEC mode.
show rpl inactive as-path-set [detail]
Syntax Description
detail |
(Optional) Displays the content of the object and all referenced objects for inactive AS path sets. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
Added the detail keyword. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl inactive as-path-set command to display all AS path sets that are not in use at an attach point either directly or indirectly but are referenced by at least one policy in the system.
Examples
This example shows the following sample configuration:
address-family ipv4 unicast
address-family ipv4 unicast
address-family ipv4 unicast
if (destination in sample) then
if (destination in prefix_set_ex1) then
if (as-path in as_path_set_ex1) then
set community (10:333) additive
if destination in prefix_set_ex1 then
if (community matches-any comm_set_ex1) then
set community (10:666) additive
if (extcommunity rt matches-any ext_comm_set_rt_ex1) then
set community (10:999) additive
if (destination in prefix_set_ex2) then
if (as-path in as_path_set_ex2) then
set community (10:333) additive
if (destination in prefix_set_ex2) then
if (community matches-any comm_set_ex2) then
set community (10:666) additive
if (extcommunity matches-any ext_comm_set_rt_ex2) then
set community (10:999) additive
Given this sample configuration, the show rpl inactive as-path-set command displays the following information:
RP/0/RP0/CPU0:router# show rpl inactive as-path-set
ACTIVE -- Referenced by at least one policy which is attached
INACTIVE -- Only referenced by policies which are not attached
UNUSED -- Not attached (directly or indirectly) and not referenced
The following as-path-sets are INACTIVE
---------------------------------------
Related Commands
show rpl inactive community-set
To display the community sets that are referenced by a policy but not any policy that is used at an attach point, use the show rpl inactive community-set command in EXEC mode.
show rpl inactive community-set [detail]
Syntax Description
detail |
(Optional) Displays the content of the object and all referenced objects for inactive community sets. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
Added the detail keyword. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl inactive community-set command to display all community sets that are not in use at an attach point either directly or indirectly but are referenced by at least one policy in the system.
Examples
This example shows the following sample configuration:
address-family ipv4 unicast
address-family ipv4 unicast
address-family ipv4 unicast
if (destination in sample2) then
if (destination in prefix_set_ex1) then
if (as-path in as_path_set_ex1) then
set community (10:333) additive
if destination in prefix_set_ex1 then
if (community matches-any comm_set_ex1) then
set community (10:666) additive
if (extcommunity rt matches-any ext_comm_set_rt_ex1) then
set community (10:999) additive
if (destination in prefix_set_ex2) then
if (as-path in as_path_set_ex2) then
set community (10:333) additive
if (destination in prefix_set_ex2) then
if (community matches-any comm_set_ex2) then
set community (10:666) additive
if (extcommunity matches-any ext_comm_set_rt_ex2) then
set community (10:999) additive
Given this sample configuration, the show rpl inactive community-set command displays the following information:
RP/0/RP0/CPU0:router# show rpl inactive community-set
ACTIVE -- Referenced by at least one policy which is attached
INACTIVE -- Only referenced by policies which are not attached
UNUSED -- Not attached (directly or indirectly) and not referenced
The following community-sets are INACTIVE
------------------------------------------
Related Commands
show rpl inactive extcommunity-set
To display the extended community sets that are referenced by a policy but not in any policy that is used at an attach point, use the show rpl inactive extcommunity-set command in EXEC mode.
show rpl inactive extcommunity-set [detail]
Syntax Description
detail |
(Optional) Displays the content of the object and all referenced objects for inactive extended community sets. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
Added the detail keyword. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl inactive extcommunity-set command to display all extended community sets that are not in use at an attach point either directly or indirectly but are referenced by at least one policy in the system.
Examples
This example shows the following sample configuration:
address-family ipv4 unicast
address-family ipv4 unicast
address-family ipv4 unicast
if (destination in sample3) then
if (destination in prefix_set_ex1) then
if (as-path in as_path_set_ex1) then
set community (10:333) additive
if destination in prefix_set_ex1 then
if (community matches-any comm_set_ex1) then
set community (10:666) additive
if (extcommunity rt matches-any ext_comm_set_rt_ex1) then
set community (10:999) additive
if (destination in prefix_set_ex2) then
if (as-path in as_path_set_ex2) then
set community (10:333) additive
if (destination in prefix_set_ex2) then
if (community matches-any comm_set_ex2) then
set community (10:666) additive
if (extcommunity matches-any ext_comm_set_rt_ex2) then
set community (10:999) additive
Given this sample configuration, the show rpl inactive extcommunity-set command displays the following information:
RP/0/RP0/CPU0:router# show rpl inactive extcommunity-set
ACTIVE -- Referenced by at least one policy which is attached
INACTIVE -- Only referenced by policies which are not attached
UNUSED -- Not attached (directly or indirectly) and not referenced
The following extcommunity-sets are INACTIVE
--------------------------------------------
Related Commands
show rpl inactive prefix-set
To display the prefix sets that are referenced by a policy but not in any policy that is used at an attach point, use the show rpl inactive prefix-set command in EXEC mode.
show rpl inactive prefix-set [detail]
Syntax Description
detail |
(Optional) Displays the content of the object and all referenced objects for inactive prefix sets. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
Added the detail keyword. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl inactive prefix-set command to display all prefix sets that are not in use at an attach point either directly or indirectly but are referenced by at least one policy in the system.
Examples
This example shows the following sample configuration:
address-family ipv4 unicast
address-family ipv4 unicast
address-family ipv4 unicast
if (destination in sample4) then
if (destination in prefix_set_ex1) then
if (as-path in as_path_set_ex1) then
set community (10:333) additive
if destination in prefix_set_ex1 then
if (community matches-any comm_set_ex1) then
set community (10:666) additive
if (extcommunity rt matches-any ext_comm_set_rt_ex1) then
set community (10:999) additive
if (destination in prefix_set_ex2) then
if (as-path in as_path_set_ex2) then
set community (10:333) additive
if (destination in prefix_set_ex2) then
if (community matches-any comm_set_ex2) then
set community (10:666) additive
if (extcommunity matches-any ext_comm_set_rt_ex2) then
set community (10:999) additive
Given this sample configuration, the show rpl inactive prefix-set command displays the following information:
RP/0/RP0/CPU0:router# show rpl inactive prefix-set
ACTIVE -- Referenced by at least one policy which is attached
INACTIVE -- Only referenced by policies which are not attached
UNUSED -- Not attached (directly or indirectly) and not referenced
The following prefix-sets are INACTIVE
--------------------------------------
Related Commands
show rpl inactive rd-set
To display the route distinguisher (RD) sets that are referenced by a policy but not in any policy that is used at an attach point, use the show rpl inactive rd-set command in EXEC mode.
show rpl inactive rd-set [detail]
Syntax Description
detail |
(Optional) Displays the content of the object and all referenced objects for inactive RD sets. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 3.4.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl inactive rd-set command to display all RD sets that are not in use at an attach point either directly or indirectly but are referenced by at least one policy in the system.
Examples
This example shows the following sample configuration:
Given this sample configuration, the show rpl inactive rd-set command displays the following information:
RP/0/RP0/CPU0:router# show rpl inactive rd-set
ACTIVE -- Referenced by at least one policy which is attached INACTIVE -- Only referenced
by policies which are not attached UNUSED -- Not attached (directly or indirectly) and not
referenced
The following rd-sets are INACTIVE
------------------------------------------
Related Commands
show rpl inactive route-policy
To display the route policies that are referenced by a policy but not in any policy that is used at an attach point, use the show rpl inactive route-policy command in EXEC mode.
show rpl inactive route-policy [detail]
Syntax Description
detail |
(Optional) Displays the content of the object and all referenced objects for inactive route policies. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The policy keyword was changed to route-policy. |
Release 3.3.0 |
Added the detail keyword. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl inactive route-policy command to display all policies that are not in use at an attach point either directly or indirectly but are referenced by at least one other policy in the system.
Examples
This example shows the following sample configuration:
address-family ipv4 unicast
address-family ipv4 unicast
address-family ipv4 unicast
if (destination in sample3) then
if (destination in prefix_set_ex1) then
if (as-path in as_path_set_ex1) then
set community (10:333) additive
if destination in prefix_set_ex1 then
if (community matches-any comm_set_ex1) then
set community (10:666) additive
if (extcommunity rt matches-any ext_comm_set_rt_ex1) then
set community (10:999) additive
if (destination in prefix_set_ex2) then
if (as-path in as_path_set_ex2) then
set community (10:333) additive
if (destination in prefix_set_ex2) then
if (community matches-any comm_set_ex2) then
set community (10:666) additive
if (extcommunity matches-any ext_comm_set_rt_ex2) then
set community (10:999) additive
Given this sample configuration, the show rpl inactive route-policy command displays the following information:
RP/0/RP0/CPU0:router# show rpl inactive route-policy
ACTIVE -- Referenced by at least one policy which is attached
INACTIVE -- Only referenced by policies which are not attached
UNUSED -- Not attached (directly or indirectly) and not referenced
The following policies are (INACTIVE)
-------------------------------------
Related Commands
show rpl maximum
To display the maximum limits for lines of configuration and number of policies, use the show rpl maximum command in EXEC mode.
show rpl maximum [lines | policies]
Syntax Description
lines |
(Optional) Displays the number of lines of configuration limit. |
policies |
(Optional) Displays the number of policies limit. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl maximum command to display the current total, current limit, and maximum limit for lines of configuration and policies.
Use the optional lines keyword to limit the display to the number of lines of configuration limits. Use the optional policies keyword to limit the display to the number of policies limits.
Examples
The following example shows sample output from the show rpl maximum command:
RP/0/RP0/CPU0:router# show rpl maximum
------------------------------------------------------------
Lines of configuration 3 65536 131072
Compiled policies size (kB) 0
Table 7 describes the significant fields shown in the display.
Table 7 show rpl maximum Field Descriptions
|
|
Lines of configuration |
Displays the current total, current limit, and maximum limit of lines for the policy. |
Policies |
Displays the current total, current limit, and maximum limit of policies. |
Compiled policies size (kB) |
Displays the current compiled total for policies in kilobytes. |
Related Commands
|
|
rpl maximum |
Configures the maximum number of lines of configuration and number of policies. |
show rpl policy-global references
To display policy-global definitions, use the show rpl policy-global references command in EXEC mode.
show rpl policy-global references [brief]
Syntax Description
brief |
(Optional) Limits the display to a list of the policy names. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 3.6.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
This example shows the following sample configuration:
route-policy set-rip-unreachable
Given this sample configuration, the show rpl policy-global references command displays the following information:
RP/0/RP0/CPU0:router# show rpl policy-global references
Usage Direct -- Reference occurs in this policy Usage Indirect -- Reference occurs via an
apply statement
Status UNUSED -- Policy is not in use at an attachpoint (unattached) Status ACTIVE --
Policy is actively used at an attachpoint Status INACTIVE -- Policy is applied by an
unattached policy
--------------------------------------------------------------
Usage Status Route-policy
--------------------------------------------------------------
Direct UNUSED set-rip-unreachable
show rpl prefix-set
To display the configuration of prefix sets, use the show rpl prefix-set command in EXEC mode.
show rpl prefix-set [name | states | brief]
Syntax Description
name |
(Optional) Name of the prefix set. |
states |
(Optional) Shows all unused, inactive, and active states. |
brief |
(Optional) Limits the display to a list of the names of all extended community sets without their configurations. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The summary keyword was replaced with brief. The * keyword was removed and the states keyword was added. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Because sets cannot hierarchically reference other sets or policies, no detail keyword exists as with the show rpl policy command.
Examples
In the following example, the configuration of prefix set pset1 is displayed:
RP/0/RP0/CPU0:router# show rpl prefix-set pset1
10.168.0.0/16 ge 16 le 32,
172.16.0.9/20 ge 20 le 32,
192.168.0.5/20 ge 20 le 32
Related Commands
show rpl prefix-set attachpoints
To display all the policies used at an attach point that reference the named prefix set, use the show rpl prefix-set attachpoints command in EXEC mode.
show rpl prefix-set name attachpoints
Syntax Description
name |
Name of a prefix set. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl prefix-set attachpoints command to display all the policies used at an attach point that reference the named prefix set either directly or indirectly.
The prefix set name is required.
Examples
This example shows the following sample configuration:
address-family ipv4 unicast
address-family ipv4 unicast
address-family ipv4 unicast
if (destination in prefix_set_ex1) then
if (as-path in as_path_set_ex1) then
set community (10:333) additive
if (destination in prefix_set_ex1) then
if (community matches-any comm_set_ex1) then
set community (10:666) additive
if (extcommunity matches-any ext_comm_set_rt_ex1) then
set community (10:999) additive
Given this sample configuration, the show rpl prefix-set prefix_set_ex1 attachpoints command displays the following information:
RP/0/RP0/CPU0:router# show rpl prefix-set prefix_set_ex1 attachpoints
Neighbor/Group type afi/safi in/out referring policy attached policy
----------------------------------------------------------------------------
10.0.101.2 -- IPv4/uni in policy_1 policy_1
10.0.101.3 -- IPv4/uni in policy_2 policy_2
Table 8 describes the significant fields shown in the display.
Table 8 show rpl prefix-set attachpoints Field Descriptions
|
|
BGP Attachpoint |
Location of the attach point. |
Neighbor/Group |
IP address of the attach point on the neighbor. |
type |
Address family mode. |
afi/safi |
Address family identifier or subsequent address family identifier. |
in/out |
Import or export policy. |
referring policy |
Policy that refers to the AS path set. |
attached policy |
Policy used at the attach point. |
Related Commands
show rpl prefix-set references
To list all the policies that reference the named prefix set, use the show rpl prefix-set references command in EXEC mode.
show rpl prefix-set name references [brief]
Syntax Description
name |
Name of the prefix set. |
brief |
(Optional) Limits the output to just a summary table and not the detailed information for the named prefix set. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The summary keyword was replaced with brief. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl prefix-set references command to list all the policies that reference the named prefix set.
Use the optional brief keyword to limit the output to just a summary table and not the detailed information for the named prefix set.
Examples
This example shows the following sample configuration:
if destination in ten-net then
set community (10:1234) additive
route-policy example-three
if destination in too-specific then
The following example displays information showing the usage and status of each policy that references the prefix set ten-net. The brief keyword limits the display to just a summary table and not the detailed information for the prefix set.
RP/0/RP0/CPU0:router# show rpl prefix-set ten-net references brief
Usage Direct -- Reference occurs in this policy
Usage Indirect -- Reference occurs via an apply statement
Status UNUSED -- Policy is not in use at an attachpoint (unattached)
Status ACTIVE -- Policy is actively used at an attachpoint
Status INACTIVE -- Policy is applied by an unattached policy
-------------------------------------------------------------
Table 9 describes the significant fields shown in the display.
Table 9 show rpl prefix-set name references Field Descriptions
|
|
Usage/Status |
Displays the usage and status of all policies that reference the prefix set. |
count |
Number of policies that match each usage and status option. |
Related Commands
show rpl rd-set
To display the configuration of route distinguisher (RD) sets, use the show rpl rd-set command in EXEC mode.
show rpl rd-set [name | states | brief]
Syntax Description
name |
(Optional) Name of the RD set. |
states |
(Optional) Shows all unused, inactive, and active states. |
brief |
(Optional) Limits the display to a list of the names of all RD sets without their configurations. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 3.4.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Because sets cannot hierarchically reference other sets or policies, no detail keyword exists as with the show rpl policy command.
Examples
In the following example, the configuration of RD set rdset1 is displayed:
RP/0/RP0/CPU0:router# show rpl rd-set rdset1
Related Commands
show rpl rd-set attachpoints
To display all the policies used at an attach point that reference the named route distinguisher (RD) set, use the show rpl rd-set attachpoints command in EXEC mode.
show rpl rd-set name attachpoints
Syntax Description
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 3.4.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl rd-set attachpoints command to display all the policies used at an attach point that reference the named RD set either directly or indirectly.
Examples
This example shows the following sample configuration:
address-family vpnv4 unicast
address-family vpnv4 unicast
route-policy rdsetmatch in
Given this sample configuration, the show rpl rd-set rdset1 attachpoints command displays the following information:
RP/0/RP0/CPU0:router# show rpl rd-set rdset attachpoints
BGP Attachpoint: Neighbor
Neighbor/Group type afi/safi in/out vrf name
--------------------------------------------------
10.0.101.1 -- IPv4/vpn in default
Table 10 describes the significant fields shown in the display.
Table 10 show rpl rd-set attachpoints Field Descriptions
|
|
Neighbor/Group |
BGP neighbor or neighbor group where the specified RD is used. |
afi/safi |
BGP address family or subaddress family where the RD set is used. |
in/out |
Direction |
vrf name |
VRF name where the RD set is used. |
Related Commands
show rpl rd-set references
To list all the policies that reference the named route distinguisher (RD) set, use the show rpl rd-set references command in EXEC mode.
show rpl rd-set name references [brief]
Syntax Description
name |
Name of the RD set. |
brief |
(Optional) Limits the output to just a summary table and not the detailed information for the RD set. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 3.4.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl rd-set references command to list all the policies that reference the named RD set.
Use the optional brief keyword to limit the output to just a summary table and not the detailed information for the named RD set.
Examples
This example shows the following sample configuration:
address-family vpnv4 unicast
address-family vpnv4 unicast
route-policy rdsetmatch in
Given this sample configuration, the show rpl rd-set rdset1 references command displays the following information:
RP/0/RP0/CPU0:router# show rpl rd-set rdset1 references
Usage Direct -- Reference occurs in this policy
Usage Indirect -- Reference occurs via an apply statement
Status UNUSED -- Policy is not in use at an attachpoint (unattached)
Status ACTIVE -- Policy is actively used at an attachpoint
Status INACTIVE -- Policy is applied by an unattached policy
--------------------------------------------------------------
route-policy usage policy status
--------------------------------------------------------------
Table 11 describes the significant fields shown in the display.
Table 11 show rpl rd-set name references Field Descriptions
|
|
route-policy |
Name of the route policy. |
usage |
Type of reference usage for the route policy. |
policy status |
Status of the route policy. |
Related Commands
show rpl route-policy
To display the configuration of route policies, use the show rpl route-policy command in EXEC mode.
show rpl route-policy [name [detail] | states | brief]
Syntax Description
name |
(Optional) Name of a route policy. |
detail |
(Optional) Displays the configuration of all policies and sets that a policy uses. |
states |
(Optional) Shows all unused, inactive, and active states. |
brief |
(Optional) Limits the display to a list of the names of all extended community sets without their configurations. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The summary keyword was replaced with brief. The policy keyword was changed to route-policy. The * keyword was removed and the states keyword was added. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the optional brief keyword to limit the display to a list of the names of policies without their configurations.
Examples
In the following example, the configuration of a route policy named policy_1 is displayed.
RP/0/RP0/CPU0:router# show rpl route-policy policy_1
if destination in prefix_set_1 and not destination in sample1 then
if as-path in aspath_set_1 then
elseif as-path in as_allowed then
set community (8660:612) additive
apply set_lpref_from_comm
If the optional detail keyword is used, all routing policy language (RPL) policies and sets that route policy policy_1 uses are displayed, as shown in the following example.
RP/0/RP0/CPU0:router# show rpl route-policy policy_1 detail
192.168.0.0/16 ge 16 le 32,
224.0.0.0/20 ge 20 le 32,
172.16.0.1/24 ge 24 le 32,
172.16.5.5/24 ge 24 le 32,
172.16.20.10/24 ge 24 le 32,
172.30.0.1/24 ge 24 le 32,
10.0.20.10/24 ge 24 le 32,
172.18.0.5/24 ge 24 le 32,
192.168.0.1/24 ge 24 le 32,
192.168.20.10/24 ge 24 le 32,
192.168.200.10/24 ge 24 le 32,
192.168.255.254/24 ge 24 le 32
ios-regex '.* _1239_ .*',
ios-regex '.* _3561_ .*',
ios-regex '.* _1755_ .*',
route-policy set_lpref_from_comm
if community matches-any (2:50) then
elseif community matches-any (2:60) then
elseif community matches-any (2:70) then
elseif community matches-any (2:80) then
elseif community matches-any (2:90) then
if destination in prefix_set_1 and not destination in sample1 then
if as-path in aspath_set_1 then
elseif as-path in as_allowed then
set community (8660:612) additive
apply set_lpref_from_comm
Related Commands
show rpl route-policy attachpoints
To display all the policies used at an attach point that reference the named policy, use the show rpl route-policy attachpoints command in EXEC mode.
show rpl route-policy name attachpoints
Syntax Description
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The policy keyword was changed to route-policy. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl route-policy attachpoints command to display all the policies used at an attach point that reference the named policy either directly or indirectly.
The policy name is required.
Examples
This example shows the following sample configuration:
address-family ipv4 unicast
address-family ipv4 unicast
address-family ipv4 unicast
RP/0/RP0/CPU0:router# show rpl route-policy policy_1
if (destination in prefix_set_ex1) then
if (as-path in as_path_set_ex1) then
set community (10:333) additive
RP/0/RP0/CPU0:router# show rpl route-policy policy_2
if (destination in prefix_set_ex1) then
if (community matches-any comm_set_ex1) then
set community (10:666) additive
if (extcommunity matches-any ext_comm_set_rt_ex1) then
set community (10:999) additive
The following command displays the route policy attach points for policy_2:
RP/0/RP0/CPU0:router# show rpl route-policy policy_2 attachpoints
BGP Attachpoint: Neighbor
Neighbor/Group type afi/safi in/out vrf name
--------------------------------------------------
10.0.101.2 -- IPv4/uni in default
10.0.101.2 -- IPv4/uni out default
Table 12 describes the significant fields shown in the display.
Table 12 show rpl route-policy attachpoints Field Descriptions
|
|
BGP Attachpoint |
Location of the attach point. |
Neighbor/Group |
IP address of the attach point on the neighbor. |
type |
Displays the address family mode. |
afi/safi |
Address family identifier or subsequent address family identifier. |
vrf name |
Name of the VPN routing and forwarding (VRF) instance. |
Related Commands
show rpl route-policy inline
To display all policies and sets that a policy uses expanded inline, use the show rpl route-policy inline command in EXEC mode.
show rpl route-policy name inline
Syntax Description
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 3.5.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl route-policy inline command to examine the configuration of a specified route policy. All policies and sets that a policy uses are gathered together and displayed expanded inline.
The policy name is required.
Examples
The following command displays the route policy policy_1:
RP/0/RP0/CPU0:router# show rpl route-policy policy_1
if destination in prefix_set_1 and not destination in martians then
if as-path in aspath_set_1 then
elseif as-path in as_allowed then
set community (8660:612) additive
apply set_lpref_from_comm
The following command displays the route policy policy_1 and all the other sets or policies it refers too inline. Adding the inline keyword causes the configuration to be displayed inline for all RPL objects that the route-policy policy_1 uses.
RP/0/RP0/CPU0:router# show rpl policy policy_1 inline
if destination in (91.5.152.0/24 ge 24 le 32, 91.220.152.0/24 ge 24 le 32,
61.106.52.0/24 ge 24 le 32, 222.168.199.0/24 ge 24 le 32, 93.76.114.0/24 ge 24 le 32,
41.195.116.0/24 ge 24 le 32, 35.92.152.0/24 ge 24 le 32, 143.144.96.0/24 ge 24 le 32,
79.218.81.0/24 ge 24 le 32, 75.213.219.0/24 ge 24 le 32, 178.220.61.0/24 ge 24 le 32,
27.195.65.0/24 ge 24 le 32) and not destination in (0.0.0.0/0, 0.0.0.0/0 ge 25 le 32,
10.0.0.0/8 ge 8 le 32, 192.168.0.0/16 ge 16 le 32, 224.0.0.0/20 ge 20 le 32, 240.0.0.0/20
ge 20 le 32) then
if as-path in (ios-regex '_9148_', ios-regex '_5870_', ios-regex '_2408_', ios-regex
'_2531_', ios-regex '_197_', ios-regex '_2992_') then
elseif as-path in (ios-regex '.* _1239_ .*', ios-regex '.* _3561_ .*', ios-regex '.*
_701_ .*', ios-regex '.* _666_ .*', ios-regex '.* _1755_ .*', ios-regex '.* _1756_ .*')
then
set community (8660:612) additive
# apply set_lpref_from_comm
if community matches-any (2:50) then
elseif community matches-any (2:60) then
elseif community matches-any (2:70) then
elseif community matches-any (2:80) then
elseif community matches-any (2:90) then
# end-apply set_lpref_from_comm
show rpl route-policy references
To list all the policies that reference the named policy, use the show rpl route-policy references command in EXEC mode.
show rpl route-policy name references [brief]
Syntax Description
name |
Name of a prefix set. |
brief |
(Optional) Limits the output to just a summary table and not the detailed information for the named policy. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The summary keyword was replaced with brief. The policy keyword was replaced with route-policy. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl route-policy references command to list all the policies that reference the named policy.
Use the optional brief keyword to limit the output to just a summary table and not the detailed information for the policy.
Examples
This example shows the following sample configuration:
if destination in ten-net then
set community (10:1234) additive
route-policy example-three
if destination in too-specific then
The following command displays information about the policy set-comms and how it is referenced:
RP/0/RP0/CPU0:router# show rpl route-policy set-comms references
Usage Direct -- Reference occurs in this policy
Usage Indirect -- Reference occurs via an apply statement
Status UNUSED -- Policy is not in use at an attachpoint (unattached)
Status ACTIVE -- Policy is actively used at an attachpoint
Status INACTIVE -- Policy is applied by an unattached policy
--------------------------------------------------------------
route-policy usage policy status
--------------------------------------------------------------
example-one Direct INACTIVE
example-three Indirect UNUSED
The direct usage indicates that the route policy example-one directly applies the policy set-comms, that is, example-one has a line in the form apply set-comms. The usage Indirect indicates that the route policy example-three does not directly apply the route policy set-comms. However, the route policy example-three does apply the policy example-one, which in turn applies the policy set-comms, so there is an indirect reference from example-three to the route policy set-comms.
The status column indicates one of three states. A policy is active if it is in use at an attach point. In the example provided, neither example-one nor example-three is in use at an attach point, which leaves two possible states: UNUSED or INACTIVE. The route policy example-one is inactive because it has some other policy (example-three) that references it, but neither example-one nor any of the policies that reference it (example-one) are in use at an attach point. The route policy example-three has a status of unused because it is not used at an attach point and no other route policies in the system refer to it.
Table 13 describes the significant fields shown in the display.
Table 13 show rpl route-policy references Field Descriptions
|
|
Usage/Status |
Displays the usage and status of all policies that reference the specified policy. Values for usage are Direct or Indirect. Values for status are ACTIVE, INACTIVE, and UNUSED. |
count |
Number of policies that match each usage and status option. |
route-policy |
One name for multiple policies that reference the specified policy. |
usage |
Type of usage for the policy. |
policy status |
Status of the policy. |
Related Commands
show rpl route-policy uses
To display information about a specified named policy, use the show rpl route-policy uses command in EXEC mode.
show rpl route-policy name uses {policies | sets | all} [direct]
Syntax Description
name |
Name of a policy. |
policies |
Generates a list of all policies that the named policy uses. |
sets |
Lists all named sets that are used by the policy. |
all |
Generates a list of both sets and policies that the named policy references. |
direct |
(Optional) Lists only the policies or sets used directly in the named policy block. Set or policy references that occur as a result of an apply statement are not listed. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The policy keyword was changed to route-policy. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl route-policy uses command to display information about a specified named policy.
Examples
This example shows the following sample configuration:
if destination in ten-net then
set community (10:1234) additive
route-policy example-three
if destination in too-specific then
The following command lists the policies one and set-comms. It also lists the prefix sets too-specific and ten-net.
RP/0/RP0/CPU0:router# show rpl route-policy example-three uses all
Policies directly and indirectly applied by this policy:
----------------------------------------------------------
Sets referenced directly and indirectly
----------------------------------------
(via applied policies) in this policy:
The sets example-one and set-comms are listed as policies that are used by the policy example-three. The policy example-one is listed because route policy example-three uses it in an apply statement. The policy set-comms is also listed because example-one applies it. Similarly, the prefix-set too-specific is used directly in the if statement in the policy example-three, and the prefix-set ten-net is used in the policy example-one. The optional direct keyword can be used to limit the output to just those sets and policies that are used within the example-three block itself, as shown in the following example:
RP/0/RP0/CPU0:router# show rpl route-policy example-three uses all direct
Policies directly applied by this policy:
------------------------------------------
Sets used directly in this policy
------------------------------------
As can be seen in the output, the route policy set-comms and the prefix set ten-net are no longer included in the output when the direct keyword is used. The direct form of the command considers only those sets or policies used in the specified route policy and any additional policies or sets that may be used if you follow the hierarchy of apply statements.
Table 14 describes the significant fields shown in the display.
Table 14 show rpl route-policy uses Field Descriptions
|
|
type |
Displays the type used in the policy configuration. Values for type are prefix-set, community-set, extcommunity-set, and as-path-set. |
show rpl unused as-path-set
To display the AS path sets that are defined but not used by a policy at an attach point or referenced in a policy using an apply statement, use the show rpl unused as-path-set command in EXEC mode.
show rpl unused as-path-set [detail]
Syntax Description
detail |
(Optional) Displays the content of the object and all referenced objects for unused AS path sets. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
Added the detail keyword. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl unused as-path-set command to display all AS path sets that are not used in a policy at an attach point either directly or indirectly and are not referenced by any policies in the system.
Examples
This example shows the following sample configuration:
address-family ipv4 unicast
address-family ipv4 unicast
address-family ipv4 unicast
as-path-set as_path_set_ex1
as-path-set as_path_set_ex2
as-path-set as_path_set_ex3
if (destination in sample) then
if (destination in prefix_set_ex1) then
if (as-path in as_path_set_ex1) then
set community (10:333) additive
if (destination in prefix_set_ex1) then
if (community matches-any comm_set_ex1) then
set community (10:666) additive
if (extcommunity matches-any ext_comm_set_rt_ex1) then
set community (10:999) additive
if (destination in prefix_set_ex2) then
if (as-path in as_path_set_ex2) then
set community (10:333) additive
if (destination in prefix_set_ex2) then
if (community matches-any comm_set_ex2) then
set community (10:666) additive
if (extcommunity matches-any ext_comm_set_rt_ex2) then
set community (10:999) additive
Given this sample configuration, the show rpl unused as-path-set command displays the following information:
RP/0/RP0/CPU0:router# show rpl unused as-path-set
ACTIVE -- Referenced by at least one policy which is attached
INACTIVE -- Only referenced by policies which are not attached
UNUSED -- Not attached (directly or indirectly) and not referenced
The following as-path-sets are UNUSED
-------------------------------------
Related Commands
show rpl unused community-set
To display the community sets that are defined but not used by a policy at an attach point or referenced in a policy using an apply statement, use the show rpl unused community-set command in EXEC mode.
show rpl unused community-set [detail]
Syntax Description
detail |
(Optional) Displays the content of the object and all referenced objects for unused community sets. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
Added the detail keyword. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl unused community-set command to display all the community sets that are not used in a policy at an attach point either directly or indirectly and are not referenced by any policies in the system.
Examples
This example shows the following sample configuration:
address-family ipv4 unicast
address-family ipv4 unicast
address-family ipv4 unicast
community-set comm_set_ex1
community-set comm_set_ex2
community-set comm_set_ex3
if (destination in sample) then
if (destination in prefix_set_ex1) then
if (as-path in as_path_set_ex1) then
set community (10:333) additive
if (destination in prefix_set_ex1) then
if (community matches-any comm_set_ex1) then
set community (10:666) additive
if (extcommunity matches-any ext_comm_set_rt_ex1) then
set community (10:999) additive
if (destination in prefix_set_ex2) then
if (as-path in as_path_set_ex2) then
set community (10:333) additive
if (destination in prefix_set_ex2) then
if (community matches-any comm_set_ex2) then
set community (10:666) additive
if (extcommunity matches-any ext_comm_set_rt_ex2) then
set community (10:999) additive
Given this sample configuration, the show rpl unused community-set command displays the following information:
RP/0/RP0/CPU0:router# show rpl unused community-set
ACTIVE -- Referenced by at least one policy which is attached
INACTIVE -- Only referenced by policies which are not attached
UNUSED -- Not attached (directly or indirectly) and not referenced
The following community-sets are UNUSED
---------------------------------------
Related Commands
show rpl unused extcommunity-set
To display the extended community sets that are defined but not used by a policy at an attach point or referenced in a policy using an apply statement, use the show rpl unused extcommunity-set command in EXEC mode.
show rpl unused extcommunity-set [cost | detail | rt | soo]
Syntax Description
cost |
(Optional) Displays the unused extended-community cost objects. |
rt |
(Optional) Displays the unused extended community RT objects. |
soo |
(Optional) Displays the unused extended-community SoO objects. |
detail |
(Optional) Displays the content of the object and all referenced objects for unused extended community sets. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
Added the following keywords: cost, rt, soo, and detail. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl unused extcommunity-set command to display all extended community sets that are not used in a policy at an attach point either directly or indirectly and are not referenced by any policies in the system.
Examples
The following is sample output for the show rpl unused extcommunity-set command:
RP/0/RP0/CPU0:router# show rpl unused extcommunity-set
ACTIVE -- Referenced by at least one policy which is attached
INACTIVE -- Only referenced by policies which are not attached
UNUSED -- Not attached (directly or indirectly) and not referenced
The following extcommunity-sets are UNUSED
------------------------------------------
Related Commands
show rpl unused prefix-set
To display the prefix sets that are defined but not used by a policy at an attach point or referenced in a policy using an apply statement, use the show rpl unused prefix-set command in EXEC mode.
show rpl unused prefix-set [detail]
Syntax Description
detail |
(Optional) Displays the content of the object and all referenced objects for unused prefix sets. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
Added the detail keyword. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl unused prefix-set command to display all prefix sets that are not used in a policy at an attach point either directly or indirectly and are not referenced by any policies in the system.
Examples
This example shows the following sample configuration:
address-family ipv4 unicast
address-family ipv4 unicast
address-family ipv4 unicast
192.168.0.0/16 ge 16 le 32,
224.0.0.0/20 ge 20 le 32,
prefix-set prefix_set_ex1
prefix-set prefix_set_ex2
220.220.220.0/24 ge 24 le 32,
220.220.120.0/24 ge 24 le 32,
220.220.130.0/24 ge 24 le 32
prefix-set prefix_set_ex3
221.221.220.0/24 ge 24 le 32,
221.221.120.0/24 ge 24 le 32,
221.221.130.0/24 ge 24 le 32
if (destination in sample) then
if (destination in prefix_set_ex1) then
if (as-path in as_path_set_ex1) then
set community (10:333) additive
if (destination in prefix_set_ex1) then
if (community matches-any comm_set_ex1) then
set community (10:666) additive
if (extcommunity matches-any ext_comm_set_rt_ex1) then
set community (10:999) additive
if (destination in prefix_set_ex2) then
if (as-path in as_path_set_ex2) then
set community (10:333) additive
if (destination in prefix_set_ex2) then
if (community matches-any comm_set_ex2) then
set community (10:666) additive
if (extcommunity matches-any ext_comm_set_rt_ex2) then
set community (10:999) additive
Given this sample configuration, the show rpl unused prefix-set command displays the following information:
RP/0/RP0/CPU0:router# show rpl unused prefix-set
ACTIVE -- Referenced by at least one policy which is attached
INACTIVE -- Only referenced by policies which are not attached
UNUSED -- Not attached (directly or indirectly) and not referenced
The following prefix-sets are UNUSED
------------------------------------
Related Commands
show rpl unused rd-set
To display the route distinguisher (RD) sets that are defined but not used by a policy at an attach point or referenced in a policy using an apply statement, use the show rpl unused rd-set command in EXEC mode.
show rpl unused rd-set [detail]
Syntax Description
detail |
(Optional) Displays the content of the object and all referenced objects for unused RD sets. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 3.4.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl unused rd-set command to display all of the RD sets that are not used in a policy at an attach point either directly or indirectly and are not referenced by any policies in the system.
Examples
The show rpl unused rd-set command displays the following information:
RP/0/RP0/CPU0:router# show rpl unused rd-set
ACTIVE -- Referenced by at least one policy which is attached
INACTIVE -- Only referenced by policies which are not attached
UNUSED -- Not attached (directly or indirectly) and not referenced
The following rd-sets are UNUSED
------------------------------------------
None found with this status.
Related Commands
show rpl unused route-policy
To display the route policies that are defined but not used at an attach point or referenced using an apply statement, use the show rpl unused route-policy command in EXEC mode.
show rpl unused route-policy [detail]
Syntax Description
detail |
(Optional) Displays the content of the object and all referenced objects for unused route policies. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The policy keyword was changed to route-policy. |
Release 3.3.0 |
Added the detail keyword. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rpl unused route-policy command to display route policies that are defined but not used at an attach point or referenced from another policy using an apply statement.
Examples
This example shows the following sample configuration:
RP/0/RP0/CPU0:router# show run | begin prefix-set
Building configuration...
prefix-set prefix_set_ex1
prefix-set prefix_set_ex2
220.220.220.0/24 ge 24 le 32,
220.220.120.0/24 ge 24 le 32,
220.220.130.0/24 ge 24 le 32
as-path-set as_path_set_ex1
as-path-set as_path_set_ex2
as-path-set as_path_set_ex3
community-set comm_set_ex1
community-set comm_set_ex2
extcommunity-set rt ext_comm_set_rt_ex1
extcommunity-set rt ext_comm_set_rt_ex2
if (destination in sample) then
if (destination in prefix_set_ex1) then
if (as-path in as_path_set_ex1) then
set community (10:333) additive
if (destination in prefix_set_ex1) then
if (community matches-any comm_set_ex1) then
set community (10:666) additive
if (extcommunity rt matches-any ext_comm_set_rt_ex1) then
set community (10:999) additive
if (destination in prefix_set_ex2) then
if (as-path in as_path_set_ex2) then
set community (10:333) additive
if (destination in prefix_set_ex2) then
if (community matches-any comm_set_ex2) then
set community (10:666) additive
if (extcommunity rt matches-any ext_comm_set_rt_ex2) then
set community (10:999) additive
route ipv4 0.0.0.0/0 10.91.37.129
route ipv4 10.91.36.0/23 10.91.37.129
route ipv4 10.91.38.0/24 10.91.37.129
In the following example, route policies that are defined but not used at an attach point or referenced from another policy using an apply statement are displayed using the show rpl unused route-policy command.
RP/0/RP0/CPU0:router# show rpl unused route-policy
ACTIVE -- Referenced by at least one policy which is attached
INACTIVE -- Only referenced by policies which are not attached
UNUSED -- Not attached (directly or indirectly) and not referenced
The following policies are (UNUSED)
-----------------------------------
Related Commands
source in
To test the source of a Border Gateway Protocol (BGP) route against the address contained in either a named or an inline prefix set, use the source in command in route-policy configuration mode.
source in {prefix-set-name | inline-prefix-set | parameter}
Syntax Description
prefix-set-name |
Name of a prefix set. |
inline-prefix-set |
Inline prefix set. The inline prefix set must be enclosed in parentheses. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
The parameter argument was added. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the source in command as a conditional expression within an if statement to test the source of the route against the data in either a named or an inline prefix set. A comparison that references a prefix set with zero elements in it returns false.
Note For a list of all conditional expressions available within an if statement, see the if command.
The source of a BGP route is the IP peering address of the neighboring router from which the route was received.
The prefix set can contain both IPv4 and IPv6 prefix specifications.
Examples
In the following example, the source of a BGP route is tested against the data in the prefix set my-prefix-set:
RP/0/RP0/CPU0:router(config)# route-policy policy-A
RP/0/RP0/CPU0:router(config-rpl)# if source in my-prefix-set then
In this example, the source of a BGP route is tested against the data in an inline IPv4 prefix set:
RP/0/RP0/CPU0:router(config)# route-policy policy-B
RP/0/RP0/CPU0:router(config-rpl)# if source in (10.0.0.8, 10.0.0.20) then
In this example, the source of a route is tested against the data in an inline IPv6 prefix set:
RP/0/RP0/CPU0:router(config)# route-policy policy-C
RP/0/RP0/CPU0:router(config-rpl)# if source in (2001:0:0:1::/64, 2001:0:0:2::/64) then
Related Commands
|
|
prefix-set |
Enters a prefix set configuration mode and defines a prefix set. |
suppress-route
To indicate that a given component of a BGP aggregate should be suppressed, use the suppress-route command in route-policy configuration mode.
suppress-route
Syntax Description
This command has no arguments or keywords.
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the suppress-route command to indicate that a given component of an aggregate should be suppressed, that is, not advertised by BGP. See the unsuppress-route command for information on overriding the suppress-route command for individual neighbors.
The suppress-route command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
Examples
In the following example, if the destination is in 10.1.0.0/16, then the route is not advertised:
RP/0/RP0/CPU0:router(config)# route-policy check-aggregate
RP/0/RP0/CPU0:router(config-rpl)# if destination in (10.1.0.0/16) then
RP/0/RP0/CPU0:router(config-rpl-if)# suppress-route
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl-if)# end-policy
Related Commands
|
|
unsuppress-route |
Indicates that a given component of an aggregate should be unsuppressed |
tag
To match a specific tag value, use the tag command in route-policy configuration mode.
tag {eq | ge | le | is} {integer | parameter}
Syntax Description
eq | ge | le | is |
Equal to; greater than or equal to; less than or equal to. |
integer |
Integer value. Range is 0 to 4294967295. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the tag command as a conditional expression within an if statement to match a specific tag value.
Note For a list of all conditional expressions available within an if statement, see the if command.
A tag is a 32-bit integer that can be associated with a given route within the RIB.
The eq operator matches either a specific tag value or a parameter value. Its variants ge and le match a range of tag values that are either greater than or equal to or less than or equal to the supplied value or parameter.
Examples
In the following example, if the tag equals 10, then the condition returns true:
RP/0/RP0/CPU0:router(config-rpl)# if tag eq 10 then
unsuppress-route
To indicate that a given component of a BGP aggregate should be unsuppressed, use the unsuppress-route command in route-policy configuration mode.
unsuppress-route
Syntax Description
This command has no arguments or keywords.
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.2 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the unsuppress-route command to indicate that a given component of an aggregate should be unsuppressed, that is, allowed to be advertised by BGP again. This command affects routes that have been suppressed in the generation of BGP aggregates. If the request to unsuppress a route is encountered in a policy at a neighbor-out attach point, it guarantees that the routes that it affects are advertised to that neighbor even if that route was suppressed using the suppress-route command in a policy at the aggregation attach point.
The unsuppress-route command can be used as an action statement within an if statement. For a list of all action statements available within an if statement, see the if command.
Examples
In the following example, if the destination is in 10.1.0.0/16, then the route is not advertised:
RP/0/RP0/CPU0:router(config)# route-policy check-aggregate
RP/0/RP0/CPU0:router(config-rpl)# if destination in (10.1.0.0/16) then
RP/0/RP0/CPU0:router(config-rpl-if)# unsuppress-route
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)# end-policy
Assuming that the policy is attached at a neighbor-out attach point, if the route 10.1.0.0/16 was suppressed in a policy at an aggregation attach point, 10.1.0.0/16 is advertised to the neighbor. Routes continue to be suppressed in advertisements to other BGP neighbors unless a specific policy is attached to unsuppress the route.
Related Commands
|
|
suppress-route |
Indicates that a given component of a BGP aggregate should be suppressed. |
vpn-distinguisher is
To match a specific Border Gateway Protocol (BGP) VPN distinguisher, use the vpn-distinguisher is command in route-policy configuration mode.
vpn-distinguisher is {number | parameter}
Syntax Description
number |
Value assigned to a 32-bit unsigned integer. Range is from 1 to 4294967295. |
parameter |
Parameter name. The parameter name must be preceded with a "$." |
Defaults
No default behavior or values
Command Modes
Route-policy configuration
Command History
|
|
Release 3.4.0 |
This command was introduced on the Cisco CRS-1 Cisco XR 12000 Series Router. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the vpn-distinguisher is command as a conditional expression within an if statement to test the value of the origin attribute.
A VPN distinguisher is used in Layer 3 VPN networks for enhanced individual VPN control and to avoid route target mapping at AS boundaries in inter-AS VPN networks. Route target extended communities are removed at neighbor outbound and the VPN distinguisher value is applied on the BGP route as an extended community. When the route is received on a neighboring router in another AS, the VPN distinguisher is removed and mapped to a route target extended community.
Note For a list of all conditional expressions available within an if statement, see the if command.
This command can be parameterized.
Examples
In the following example, the origin is tested within an if statement to learn if it is either igp or egp:
RP/0/RP0/CPU0:router(config-rpl)# if origin is igp or origin is egp then
In the following example, a parameter is used to match a specific origin type:
RP/0/RP0/CPU0:router(config)# route-policy bar($origin)
RP/0/RP0/CPU0:router(config-rpl)# if origin is $origin then
RP/0/RP0/CPU0:router(config-rpl-if)# set med 20
RP/0/RP0/CPU0:router(config-rpl-if)# endif
RP/0/RP0/CPU0:router(config-rpl)#