RSVP Infrastructure Commands on
Cisco IOS XR Software
This chapter describes the commands that you will use to configure and use Resource Reservation Protocol (RSVP). RSVP is a signaling protocol used to set up, maintain, and control end-to-end quality-of-service (QoS) reservations over IP. RSVP is specified in Internet Engineering Task Force (IETF) RFC 2205 (ftp://ftp.isi.edu/in-notes/rfc2205.txt).
The protocol has been extended to signal Multiprotocol Label Switching traffic engineering (MPLS-TE) tunnels, as specified in the IETF RFC 3209, RSVP-TE: Extensions to RSVP for LSP Tunnels and Optical UNI tunnels, as specified in the Optical Internetworking Forum (OIF) document OIF2000.125.7, User Network Interface (UNI) 1.0, Signalling Specification. The RSVP implementation also supports fault handling as specified in IETF RFC 3473, Generalized Multiprotocol Label Switching (GMPLS) Signaling RSVP-TE extensions.
RFC2747, RSVP Cryptographic Authentication is also supported.
For detailed information about MPLS concepts, configuration tasks, and examples, refer to the
Cisco IOS XR MPLS Configuration Guide.
authentication (RSVP)
To enter RSVP authentication submode, use the authentication command in global configuration mode, RSVP interface configuration mode, or RSVP neighbor configuration mode. To remove authentication parameters in the applicable submode, use the no form of this command.
authentication
no authentication
Syntax Description
This command has no arguments or keywords.
Defaults
The default value is no authentication, which means that the feature is disabled.
Command Modes
Global configuration
RSVP interface configuration
RSVP neighbor configuration
Command History
|
|
Release 3.4.1 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the authentication command to enter RSVP authentication configuration mode.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to enter RSVP authentication configuration mode from global configuration mode:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp authentication
RP/0/RP0/CPU0:router(config-rsvp-auth)#
The following example shows how to activate the RSVP on an interface and enter RSVP authentication configuration mode:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp interface pos 0/2/1/0
RP/0/RP0/CPU0:router(config-rsvp-if)# authentication
RP/0/RP0/CPU0:router(config-rsvp-if-auth)#
The following example shows how to configure the RSVP neighbor with IP address 1.1.1.1 and enter neighbor authentication configuration mode:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp neighbor 1.1.1.1
RP/0/RP0/CPU0:router(config-rsvp-nbor)# authentication
RP/0/RP0/CPU0:router(config-rsvp-nbor-auth)#
Related Commands
bandwidth (RSVP)
To configure RSVP bandwidth on an interface using prestandard DS-TE mode, use the bandwidth command in RSVP interface configuration mode. To reset the RSVP bandwidth on that interface to its default value, use the no form of this command.
bandwidth [total reservable bandwidth] [bc0 bandwidth] [global-pool bandwidth] [sub-pool reservable-bw]
no bandwidth [total reservable bandwidth] [bc0 bandwidth] [global-pool bandwidth] [sub-pool reservable-bw]
Syntax Description
total reservable bandwidth |
(Optional) Total reservable bandwidth (in kbps) that RSVP accepts for reservations on this interface. Range is 0 to 4294967295 Kbps. |
bc0 bandwidth |
Configures the total reservable bandwidth in the bc0 pool (in Kbps, Mbps or Gbps). The default is Kbps. Range is 0 to 4294967295. |
global-pool bandwidth |
(Optional) Configures the total reservable bandwidth in the global-pool. Range is 0 to 4294967295 Kbps. |
Defaults
If the command is entered without the optional arguments, the RSVP total bandwidth is set to 75 percent of the intrinsic bandwidth of the interface. If the interface has no (0) intrinsic bandwidth, then no bandwidth is reserved for RSVP.
Command Modes
RSVP interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
The sub-pool keyword was added. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
RSVP is enabled either using the rsvp interface command or when MPLS is configured on the interface. In addition, there are other instances in which RSVP is enabled automatically; for example, when an RSVP message is received on an interface that is not configured under RSVP or MPLS (such as out-of-band signaling for an Optical User Network Interface application).
If RSVP reservation messages are received on an interface different from the one through which the corresponding Path message was sent out, the interfaces are adjusted such that all resource reservations, such as bandwidth, are done on the outgoing interface of the Path message.
Prestandard DS-TE uses the Cisco proprietary mechanisms for RSVP signaling and IGP advertisements. This DS-TE mode does not interoperate with third-party vendor equipment. Note that prestandard DS-TE is enabled only after configuring the sub-pool bandwidth values on MPLS-enabled interfaces.
Note You can also configure RSVP bandwidth on an interface using IETF DS-TE mode. This mode supports multiple bandwidth constraint models, including the Russian Doll Model (RDM) and the Maximum Allocation Model (MAM) both with two bandwidth pools.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to limit the total of all RSVP reservations on POS interface 0/3/0/0 to 5000 Kbps:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp interface pos 0/3/0/0
RP/0/RP0/CPU0:router(config-rsvp)# bandwidth 5000
Related Commands
|
|
bandwidth mam (RSVP) |
Configures RSVP bandwidth on an interface using the Maximum Allocation Model (MAM) bandwidth constraints model. |
bandwidth rdm (RSVP) |
Configures RSVP bandwidth on an interface using the Russian Doll Model (RDM) bandwidth constraints model. |
bandwidth mam (RSVP)
To configure RSVP bandwidth on an interface using the Maximum Allocation Model (MAM) bandwidth constraints model, use the bandwidth mam command in RSVP interface configuration mode. To return to the default behavior, use the no form of this command.
bandwidth mam {total reservable bandwidth | max-reservable-bw maximum-reservable-bw}
no bandwidth mam {total reservable bandwidth | max-reservable-bw maximum-reservable-bw}
Syntax Description
total reservable bandwidth |
Total reservable bandwidth (in kbps) that RSVP accepts for reservations on this interface. Range is 0 to 4294967295 Kbps. |
max-reservable-bw maximum-reservable-bw |
Configures the maximum reservable bandwidth (in kbps) that RSVP accepts for reservations on this interface. Range is 0 to 4294967295 Kbps. |
Defaults
If the command is entered without the optional arguments, the RSVP total bandwidth is set to 75 percent of the intrinsic bandwidth of the interface. If the interface has no (0) intrinsic bandwidth, then no bandwidth is reserved for RSVP.
Command Modes
RSVP interface configuration
Command History
|
|
Release 3.3 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Both the MAM and RDM models can be configured on a single interface to allow switching between each model.
Note Non-stop forwarding (NSF) is not guaranteed when the bandwidth constraint model is changed.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to limit the total of all RSVP reservations on POS interface 0/3/0/0 to 7500 kbps:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp interface pos 0/3/0/0
RP/0/RP0/CPU0:router(config-rsvp-if)# bandwidth mam 7500
Related Commands
|
|
bandwidth (RSVP) |
Configures RSVP bandwidth on an interface using prestandard DS-TE mode. |
bandwidth rdm (RSVP) |
Configures RSVP bandwidth on an interface using the Russian Doll Model (RDM) bandwidth constraints model. |
rsvp bandwidth mam |
Configures the RSVP default interface bandwidth for the maximum reservable bandwidth parameters using the Maximum Allocation Model (MAM) bandwidth constraints model. |
rsvp bandwidth rdm |
Configures the RSVP default interface bandwidth for the maximum reservable bandwidth parameters using the Russian Doll Model (RDM) bandwidth constraints model. |
bandwidth rdm (RSVP)
To configure RSVP bandwidth on an interface using the Russian Doll Model (RDM) bandwidth constraints model, use the bandwidth rdm command in RSVP interface configuration mode. To return to the default behavior, use the no form of this command.
bandwidth rdm {total-reservable-bw | bc0 | global-pool} {sub-pool | bc1 reservable-bw}
no bandwidth rdm {total-reservable-bw | bc0 | global-pool} {sub-pool | bc1 reservable-bw}
Syntax Description
total-reservable-bw |
Total reservable bandwidth (in Kbps, Mbps or Gbps). The default value is expressed in Kbps. |
bc0 |
Reserves bandwidth in the bc0 pool. |
global-pool |
Reserves bandwidth in the global pool. |
sub-pool |
Reserves bandwidth in the sub-pool. |
bc1 |
Reserves bandwidth in the bc1 pool. |
reservable-bw |
Reservable bandwidth in the sub- and bc1 pools (in Kbps, Mbps or Gbps). The default value is expressed in Kbps. |
Defaults
sub-pool-bw: 0
global-pool and bc0: default value expressed in Kbps
Note If the command is entered without the optional arguments, the RSVP total bandwidth is set to 75 percent of the intrinsic bandwidth of the interface. If the interface has no (0) intrinsic bandwidth, then no bandwidth is reserved for RSVP.
Command Modes
RSVP interface configuration
Command History
|
|
Release 3.3 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Both the MAM and RDM bandwidth constraint models support up two bandwidth pools.
Cisco IOS XR software provides global configuration when switching between bandwidth constraint models. Both models are configured on a single interface to allow switching between models.
Note Non-stop forwarding (NSF) is not guaranteed when the bandwidth constraint model is changed.
The global pool and sub-pool keywords are included in this command for backward compatibility with prestandard DS-TE. The global pool keyword is equivalent to the bc0 keyword. The sub-pool keyword is equivalent to the bc1 keyword.
RDM is the default bandwidth constraint model used in both pre-standard and IETF mode.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to limit the total of all RSVP reservations on POS interface 0/3/0/0 to 7500 kbps, and allows each single flow to reserve no more than 1000 kbps:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp interface pos 0/3/0/0
RP/0/RP0/CPU0:router(config-rsvp-if)# bandwidth rdm 7500 1000
Related Commands
|
|
bandwidth (RSVP) |
Configures RSVP bandwidth on an interface using prestandard DS-TE mode. |
bandwidth mam (RSVP) |
Configures RSVP bandwidth on an interface using the Maximum Allocation Model (MAM) bandwidth constraints model. |
rsvp bandwidth mam |
Configures the RSVP default interface bandwidth for the maximum reservable bandwidth parameters using the Maximum Allocation Model (MAM) bandwidth constraints model. |
rsvp bandwidth rdm |
Configures the RSVP default interface bandwidth for the maximum reservable bandwidth parameters using the Russian Doll Model (RDM) bandwidth constraints model. |
clear rsvp authentication
To eliminate RSVP security association (SA) before the lifetime expires, use the clear rsvp authentication command in EXEC mode.
clear rsvp authentication [type interface-path-id] [destination IP address] [source IP address]
Syntax Description
type |
(Optional) Interface type. For more information, use the question mark (?) online help function. |
interface-path-id |
Physical interface or a virtual interface. Note Use the show interfaces command to see a list of all possible interfaces currently configured on the router. For more information about the syntax for the router, use the question mark (?) online help function. |
destination IP address |
(Optional) Eliminates the RSVP security associations (SA) before their lifetimes expire. All SAs with this destination IP address are cleared. |
source IP address |
(Optional) Eliminates the RSVP security associations (SA) before their lifetimes expire. All SAs with this source IP address are cleared. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 3.4.1 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the clear rsvp authentication command for the following reasons:
•To eliminate security associations before their lifetimes expire
•To free up memory
•To resolve a problem with a security association being in an indeterminate state
You can delete all RSVP security associations if you do not enter an optional filter (interface, source, or destination IP address).
If you delete a security association, it is recreated as needed.
|
|
mpls-te |
execute |
ouni |
execute |
Examples
The following example shows how to clear each SA:
RP/0/RP0/CPU0:router# clear rsvp authentication
The following example shows how to clear each SA with the destination address 1.1.1.1:
RP/0/RP0/CPU0:router# clear rsvp authentication destination 1.1.1.1
The following example shows how to clear each SA with the source address 2.2.2.2:
RP/0/RP0/CPU0:router# clear rsvp authentication source 2.2.2.2
The following example shows how to clear each SA with the POS interface 0/2/1/0:
RP/0/RP0/CPU0:router# clear rsvp authentication POS 0/2/1/0
The following example shows how to clear each SA on the POS interface 0/2/1/0, destination address 1.1.1.1, and source address 2.2.2.2:
RP/0/RP0/CPU0:router# clear rsvp authentication POS 0/2/1/0 destination 1.1.1.1 source
2.2.2.2
Related Commands
|
|
life-time (RSVP) |
Controls how long RSVP maintains idle security associations with other trusted RSVP neighbors. |
clear rsvp counters authentication
To eliminate RSVP counters for each security association (SA), use the clear rsvp counters authentication command in EXEC mode.
clear rsvp counters authentication [type interface-path-id] [destination IP address] [source IP address]
Syntax Description
type |
(Optional) Interface type. For more information, use the question mark (?) online help function. |
interface-path-id |
Physical interface or a virtual interface. Note Use the show interfaces command to see a list of all possible interfaces currently configured on the router. For more information about the syntax for the router, use the question mark (?) online help function. |
destination IP address |
(Optional) Eliminates authentication-related statistics for each security association (SA) with this destination IP address. |
source IP address |
(Optional) Eliminates authentication-related statistics for each security association (SA) with this source IP address. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 3.4.1 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
|
|
mpls-te |
execute |
ouni |
execute |
Examples
The following example shows how to clear authentication counters for each SA:
RP/0/RP0/CPU0:router# clear rsvp counters authentication
The following example shows how to clear authentication counters for each SA with the destination address 1.1.1.1:
RP/0/RP0/CPU0:router# clear rsvp counters authentication destination 1.1.1.1
The following example shows how to clear authentication counters for each SA with the source address 2.2.2.2:
RP/0/RP0/CPU0:router# clear rsvp counters authentication source 2.2.2.2
The following example shows how to clear authentication counters for each SA with the POS interface 0/2/1/0:
RP/0/RP0/CPU0:router# clear rsvp counters authentication POS 0/2/1/0
The following example shows how to clear authentication counters for each SA on the POS interface 0/2/1/0, destination address 1.1.1.1, and source address 2.2.2.2:
RP/0/RP0/CPU0:router# clear rsvp counters authentication POS 0/2/1/0 destination 1.1.1.1
source 2.2.2.2
clear rsvp counters all
To clear (set to zero) all RSVP message and event counters that are being maintained by the router, use the clear rsvp counters all command in EXEC mode.
clear rsvp counters all type interface-path-id
Syntax Description
type |
(Optional) Interface type. For more information, use the question mark (?) online help function. |
interface-path-id |
Physical interface or a virtual interface. Note Use the show interfaces command to see a list of all possible interfaces currently configured on the router. For more information about the syntax for the router, use the question mark (?) online help function. |
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to clear all message and event counters:
RP/0/RP0/CPU0:router# clear rsvp counters all
Related Commands
clear rsvp counters chkpt
To clear RSVP checkpoint counters, use the clear rsvp counters chkpt command in EXEC mode.
clear rsvp counters chkpt
Syntax Description
This command has no arguments or keywords.
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to clear all message and event counters:
RP/0/RP0/CPU0:router# clear rsvp counters chkpt
Related Commands
clear rsvp counters events
To clear (set to zero) all RSVP event counters that are being maintained by the router, use the clear rsvp counters events command in EXEC mode.
clear rsvp counters events [type interface-path-id]
Syntax Description
type |
(Optional) Interface type. For more information, use the question mark (?) online help function. |
interface-path-id |
Physical interface or a virtual interface. Note Use the show interfaces command to see a list of all possible interfaces currently configured on the router. For more information about the syntax for the router, use the question mark (?) online help function. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the clear rsvp counters events command to set all RSVP event counters to zero.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to clear all event counters:
RP/0/RP0/CPU0:router# clear rsvp counters events
Related Commands
clear rsvp counters messages
To clear (set to zero) all RSVP message counters that are being maintained by the router, use the clear rsvp counters messages command in EXEC mode.
clear rsvp counters messages [type interface-path-id]
Syntax Description
type |
(Optional) Interface type. For more information, use the question mark (?) online help function. |
interface-path-id |
Physical interface or a virtual interface. Note Use the show interfaces command to see a list of all possible interfaces currently configured on the router. For more information about the syntax for the router, use the question mark (?) online help function. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the clear rsvp counters messages command to set all RSVP message counters to zero.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to set all RSVP message counters for POS interface 0/3/0/2 to zero:
RP/0/RP0/CPU0:router# clear rsvp counters messages pos0/3/0/2
Related Commands
clear rsvp counters oor
To clear internal RSVP counters on out of resources (OOR) events, use the clear rsvp counters oor command in EXEC mode.
clear rsvp counters oor [type interface-path-id]
Syntax Description
type |
(Optional) Interface type. For more information, use the question mark (?) online help function. |
interface-path-id |
Physical interface or a virtual interface. Note Use the show interfaces command to see a list of all possible interfaces currently configured on the router. For more information about the syntax for the router, use the question mark (?) online help function. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 3.2 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the clear rsvp counters oor command to set RSVP OOR counters to zero.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example show how to clear all RSVP message counters for POS interface 0/3/0/2 to zero:
RP/0/RP0/CPU0:router# clear rsvp counters oor pos0/3/0/2
Related Commands
clear rsvp counters prefix filtering
To clear internal prefix-filtering related RSVP counters, use the clear rsvp counters prefix-filtering command in EXEC mode.
clear rsvp counters prefix-filtering {interface [type interface-path-id] | access-list [aclname]}
Syntax Description
interface |
Clears RSVP prefix-filtering counters for all interfaces. |
type |
(Optional) Interface type. For more information, use the question mark (?) online help function. |
interface-path-id |
Physical interface or a virtual interface. Note Use the show interfaces command to see a list of all possible interfaces currently configured on the router. For more information about the syntax for the router, use the question mark (?) online help function. |
access-list |
(Optional) Clears RSVP prefix-filtering counters for access control list. |
aclname |
Name of the access list. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 3.2 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the clear rsvp counters prefix-filtering command to set RSVP prefix-filtering related RSVP counters to zero.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to set all RSVP message counters for POS interface 0/3/0/2 to zero:
RP/0/RP0/CPU0:router# clear rsvp counters prefix-filtering interface pos0/3/0/2
The following example shows how to set all RSVP prefix-filtering counters for access-list banks to zero:
RP/0/RP0/CPU0:router# clear rsvp counters prefix-filtering access-list banks
Related Commands
key-source key-chain (RSVP)
To specify the source of the key information to authenticate RSVP messages, use the key-source key-chain command in the appropriate RSVP authentication configuration mode. To remove the key source from the appropriate RSVP authentication configuration mode, use the no form of this command.
key-source key-chain key-chain-name
no key-source key-chain key-chain-name
Syntax Description
key-chain-name |
Name of the keychain. The maximum number of characters is 32. |
Defaults
The default value is none, which means that the key source is not specified.
Command Modes
RSVP authentication configuration
RSVP interface authentication configuration
RSVP neighbor authentication configuration
Command History
|
|
Release 3.4.1 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Note•RSVP authentication is enabled regardless of whether or not the specified keychain exists or has no available keys to use. If the specified keychain does not exist or there are no available keys in the keychain, RSVP authentication processing fails.
•The key-source key-chain command does not create a keychain but just specifies which keychain to use. You must configure a keychain first. For an example of how a key chain is configured, see the Cisco IOS XR System Security Configuration Guide.
•The no key-source key-chain command does not necessarily disable the authentication.
•RSVP authentication supports only keyed-hash message authentication code (HMAC)-type algorithms.
Note For inheritance procedures, see Cisco IOS XR MPLS Configuration Guide.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows that the source of the key information is specified for the keychain mpls-keys in RSVP authentication configuration mode:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp authentication
RP/0/RP0/CPU0:router(config-rsvp-auth)# key-source key-chain mpls-keys
The following example shows that the source of the key information is specified for the keychain mpls-keys for a POS interface in RSVP authentication configuration mode:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp interface POS 0/2/1/0
RP/0/RP0/CPU0:router(config-rsvp-if)# authentication
RP/0/RP0/CPU0:router(config-rsvp-if-auth)# key-source key-chain mpls-keys
The following example shows that the source of the key information is specified for the keychain mpls-keys in RSVP neighbor authentication configuration mode:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp neighbor 1.1.1.1 authentication
RP/0/RP0/CPU0:router(config-rsvp-nbor-auth)# key-source key-chain mpls-keys
Related Commands
|
|
life-time (RSVP) |
Controls how long RSVP maintains idle security associations with other trusted RSVP neighbors. |
window-size (RSVP) |
Specifies the tolerance to accept out-of-sequence messages. |
life-time (RSVP)
To control how long RSVP maintains idle security associations with other trusted RSVP neighbors, use the life-time command in the appropriate RSVP authentication configuration mode. To disable the lifetime setting, use the no form of this command.
life-time seconds
no life-time seconds
Syntax Description
seconds |
Length of time (in seconds) that RSVP maintains security associations with other trusted RSVP neighbors. Range is 30 to 86400. |
Defaults
seconds: 1800 seconds (30 minutes)
Command Modes
RSVP authentication configuration
RSVP interface authentication configuration
RSVP neighbor authentication configuration
Command History
|
|
Release 3.4.1 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
For inheritance procedures, see the Cisco IOS XR MPLS Configuration Guide.
Use the life-time (RSVP) command to indicate when to end idle security associations with RSVP trusted neighbors.
By setting a larger lifetime, the router remembers the state for a long period time, which provides better protection against a replay attack.
Use the clear rsvp authentication command to free security associations before their lifetimes expire.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to configure a lifetime of 2000 seconds for each SA in RSVP authentication configuration mode:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp authentication
RP/0/RP0/CPU0:router(config-rsvp-auth)# life-time 2000
The following example shows how to configure a lifetime of 2000 seconds for each SA in RSVP neighbor authentication configuration mode:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp neighbor 1.1.1.1 authentication
RP/0/RP0/CPU0:router(config-rsvp-nbor-auth)# life-time 2000
The following example shows how to configure a lifetime of 2000 seconds for each SA in RSVP interface authentication configuration mode:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp interface POS 0/2/1/0
RP/0/RP0/CPU0:router(config-rsvp-if)# authentication
RP/0/RP0/CPU0:router(config-rsvp-if-auth)# life-time 2000
Related Commands
rsvp bandwidth mam
To configure the RSVP default interface bandwidth for the maximum reservable bandwidth parameters using the Maximum Allocation Model (MAM) bandwidth constraints model, use the rsvp bandwidth mam command in global configuration mode. To return to the default of 75% for the global (BC0) and BC1 pools, use the no form of this command.
rsvp bandwidth mam max-reservable percentage percent [bc0 percentage bc0-percent] [bc1 percentage bc1-percent]
no rsvp bandwidth mam max-reservable percentage percent [bc0 percentage bc0-percent] [bc1 percentage bc1-percent]
Syntax Description
max-reservable |
Configures the maximum reservable bandwidth. |
percentage percent |
Configures the maximum reservable bandwidth percentage. |
bc0 percentage |
(Optional) Configures the BC0 global pool bandwidth percentage. |
bc0-percent |
Percentage for the BC0 pool bandwidth interface. Range is from 0 to 10000. Use this range to under-book or over-book RSVP bandwidth on the interface. Note Before you configure the percentage for the BC0 pool, configure the maximum reservable bandwidth pool. |
bc1 percentage |
(Optional) Configures the BC1 subpool bandwidth percentage. |
bc1-percent |
Percentage for the BC1 pool bandwidth interface. Range is from 0 to 10000. Use this range to under-book or over-book RSVP bandwidth on the interface. Note Before you configure the percentage for the BC1 pool, configure the maximum reservable bandwidth for the BC0 pool. |
Command Default
If the command is entered without the optional arguments, the RSVP total bandwidth is set to 75 percent of the intrinsic bandwidth of the interface. If the interface has no (0) intrinsic bandwidth, then no bandwidth is reserved for RSVP.
Command Modes
Global configuration
Command History
|
|
Release 3.8.4 |
This command was introduced. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The percentage keyword allows for over-booking. The configured value overwrites the current default value of 75%.
RSVP and MPLS-TE uses these defaults to automatically set the BC0 (global pool) and BC1 (subpool) for any RSVP configured interface without specifying an absolute bandwidth.
The bandwidth is configured as a percentage instead of an absolute number. Automatic adjustment is based on the total interface bandwidth changes. The maximum reservable bandwidth automatically is readjusted when the interface bandwidth changes, for example, when adding or removing a bundle member.
You can specify the default percentage for the maximum reservable bandwidth, BC0 (global pool), BC1 (subpool), or either pool.
To configure a default for the BC0 pool, first configure one for the global pool. To configure a default for the BC1 pool, first configure one for the BC0 pool.
Each pool uses the following values:
•Explicit value configured on the interface for this pool.
•Default percentage value configured for this pool.
•Pool parent value (global is parent of both BC0 and BC1). This does not apply to the global pool since it does not have a parent.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to configure RSVP default interface bandwidth percentage for the maximum reservable bandwidth using MAM:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp bandwidth mam max-reservable percentage 5000 bc0
percentage 3000
Related Commands
|
|
bandwidth mam (RSVP) |
Configures RSVP bandwidth on an interface using the Maximum Allocation Model (MAM) bandwidth constraints model. |
bandwidth rdm (RSVP) |
Configures RSVP bandwidth on an interface using the Russian Doll Model (RDM) bandwidth constraints model. |
rsvp bandwidth rdm |
Configures the RSVP default interface bandwidth for the maximum reservable bandwidth parameters using the Russian Doll Model (RDM) bandwidth constraints model |
show rsvp interface |
Displays information about all interfaces with RSVP enabled. |
rsvp bandwidth rdm
To configure the RSVP default interface bandwidth for the maximum reservable bandwidth parameters using the Russian Doll Model (RDM) bandwidth constraints model, use the rsvp bandwidth rdm command in global configuration mode. To return to the default of 75% for the maximum reservable BC0 pool and 0% for the BC1 pools, use the no form of this command.
rsvp bandwidth rdm max-reservable-bc0 percentage percent [bc1 percentage bc1-percent]
no rsvp bandwidth rdm max-reservable-bc0 percentage percent [bc1 percentage bc1-percent]
Syntax Description
max-reservable-bc0 |
Configures the maximum reservable bandwidth for the BC0 global pool. |
percentage percent |
Percentage for the BC0 pool bandwidth interface. Range is from 0 to 10000. Use this range to under-book or over-book RSVP bandwidth on the interface. |
bc1 percentage |
(Optional) Configures the BC1 subpool percentage for the bandwidth. |
bc1-percent |
Percentage for the BC1 pool bandwidth interface. Range is from 0 to 10000. Note Before you configure the percentage for the BC1 pool, configure the maximum reservable bandwidth for the BC0 pool. |
Command Default
If the command is entered without the optional arguments, the RSVP total bandwidth is set to 75 percent of the intrinsic bandwidth of the interface. If the interface has no (0) intrinsic bandwidth, then no bandwidth is reserved for RSVP.
Command Modes
Global configuration
Command History
|
|
Release 3.8.4 |
This command was introduced. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The percentage keyword allows for over-booking. The configured value overwrites the current default value of 75%.
RSVP and MPLS-TE use these defaults to automatically set the BC0 (global pool) and BC1 (subpool) for any RSVP configured interface without specifying an absolute bandwidth.
The bandwidth is configured as a percentage instead of an absolute number. Automatic adjustment is based on the total interface bandwidth changes. The maximum reservable bandwidth is automatically readjusted when the interface bandwidth changes, for example, when adding or removing a bundle member.
You can specify the default percentage for the maximum reservable bandwidth for the BC0 (global pool), BC1 (subpool), or either pool.
Each pool uses the following values:
•Explicit value configured on the interface for this pool.
•Default percentage value configured for this pool.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to configure RSVP default interface bandwidth percentage for the maximum reservable bandwidth using RDM:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp bandwidth rdm max-reservable-bc0 percentage 3000 bc1
percentage 5000
Related Commands
|
|
bandwidth mam (RSVP) |
Configures RSVP bandwidth on an interface using the Maximum Allocation Model (MAM) bandwidth constraints model. |
bandwidth rdm (RSVP) |
Configures RSVP bandwidth on an interface using the Russian Doll Model (RDM) bandwidth constraints model. |
rsvp bandwidth mam |
Configures the RSVP default interface bandwidth for the maximum reservable bandwidth parameters using the Maximum Allocation Model (MAM) bandwidth constraints model. |
show rsvp interface |
Displays information about all interfaces with RSVP enabled. |
rsvp interface
To configure RSVP on an interface, use the rsvp interface command in global configuration mode. To disable RSVP on that interface, use the no form of this command.
rsvp interface type interface-path-id}
no rsvp interface type interface-path-id
Syntax Description
type |
(Optional) Interface type. For more information, use the question mark (?) online help function. |
interface-path-id |
Physical interface or a virtual interface. Note Use the show interfaces command to see a list of all possible interfaces currently configured on the router. For more information about the syntax for the router, use the question mark (?) online help function. |
Defaults
RSVP is enabled by default on an interface under the following conditions. (Enabling RSVP on an interface means that interface can be used by RSVP to send and receive RSVP messages).
•RSVP is configured on that interface using the rsvp interface command.
•MPLS is configured on that interface.
•Automatically enabled as in the case of out-of-band signaling for the Optical User Network Interface (O-UNI) application, where an RSVP message could be received on an interface which is not configured under RSVP or MPLS.
Command Modes
Global configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
When RSVP is enabled on an interface by any of the three methods mentioned in the above section, the default bandwidth is 0. Use the bandwidth command in RSVP interface configuration mode to configure the bandwidth on an interface.
If the interface bandwidth is 0, RSVP can be used only to signal flows that do not require bandwidth on this interface. In the case of O-UNI, 0 bandwidth is not an issue, because O-UNI does not use bandwidth as a resource.
The rsvp interface command enables the RSVP interface configuration submode.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to enable the RSVP interface configuration submode and to enable RSVP on this interface with 0 bandwidth:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp interface pos 0/3/0/0
Related Commands
|
|
bandwidth (RSVP) |
Configures RSVP bandwidth on an interface using prestandard DS-TE mode. |
signalling dscp (RSVP) |
Gives all RSVP packets sent out on a specific interface higher priority in the network by marking them with a particular differentiated services code point (DSCP). |
rsvp neighbor
To specify an RSVP neighbor, use the rsvp neighbor command in global configuration mode. To deactivate authentication for a neighbor, use the no form of this command.
rsvp neighbor IP address authentication
no rsvp neighbor IP address authentication
Syntax Description
IP address |
IP address of the neighbor. A single IP address of a specific neighbor; usually one of the neighbor's physical or logical (loopback) interfaces. |
authentication |
Configures RSVP authentication parameters. |
Defaults
No default values or behaviors
Command Modes
Global configuration
Command History
|
|
Release 3.4.1 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Note RSVP neighbor configuration mode can be used only if you want to configure authentication for a particular neighbor.
Use the rsvp neighbor command to enter RSVP neighbor authentication configuration mode.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to enter RSVP neighbor authentication configuration mode for IP address 1.1.1.1:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp neighbor 1.1.1.1 authentication
RP/0/RP0/CPU0:router(config-rsvp-nbor-auth)#
Related Commands
show rsvp authentication
To display the database for the security association that RSVP has established with other RSVP neighbors, use the show rsvp authentication command in EXEC mode.
show rsvp authentication [type interface-path-id] [destination IP address] [detail] [mode {receive | send}] [neighbor IP address] [source IP address]
Syntax Description
type |
(Optional) Interface type. For more information, use the question mark (?) online help function. |
interface-path-id |
Physical interface or a virtual interface. Note Use the show interfaces command to see a list of all possible interfaces currently configured on the router. For more information about the syntax for the router, use the question mark (?) online help function. |
destination IP address |
Displays the database for the security association (SA) for the destination IP address. The IP address argument is the IP address of the destination address. |
detail |
(Optional) Displays additional information about RSVP security SAs. |
mode |
(Optional) Specifies the SA type. An SA is used to authenticate either incoming (receive) or outgoing (send) messages. |
receive |
Displays SAs for incoming messages. |
send |
Displays SAs for outgoing messages. |
neighbor IP address |
(Optional) Displays the RSVP authentication information for the neighbor IP address. The IP address argument is the IP address of the neighbor. For the send SA, the neighbor address is the destination address. For receive, the neighbor address is the source address. |
source IP address |
(Optional) Displays the database for the SA for the source IP address. The IP address argument is the IP address of the source address. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 3.4.1 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following sample output displays information for RSVP authentication:
RP/0/RP0/CPU0:router# show rsvp authentication
Codes: S - static, G - global, N - neighbor, I -interface, C - chain
Source Address Dest Address Interface Mode Key-Source Key-ID Code
3.0.0.1 3.0.0.2 PO0/7/0/2 Send mpls-keys 1 SGC
3.0.0.2 3.0.0.1 PO0/7/0/2 Recv mpls-keys 1 SGC
Table 53 describes the significant fields shown in the display.
Table 53 show rsvp authentication Field Descriptions
|
|
Source Address |
IP address of the sender. For Send mode, this is the local address (either the address of the Interface field or the local router ID). For Recv mode, this is the address of the RSVP neighbor. |
Dest Address |
IP address of the receiver. For Send mode, this is the address of the RSVP neighbor. For Recv mode, this is the local address (either the address of the Interface field or the local router ID). |
Interface |
Name of the interface over which the security association is being maintained. |
Mode |
Direction of the association for the following mode types: •Send—Authenticates messages that you forward. •Recv—Authenticates messages that you receive. |
Key-Source |
Key source identification string that is currently set to the configured keychain name. |
Key-ID |
The last successful key ID that is used for authentication and that maps to the keychain ID configuration. If the value is too large to fit into the column, it is truncated and a (..) suffix is appended. Use the detail mode to see the non-truncated key ID. |
Code |
Code field has the following terms: •Static—Key is static and configured. •Global—Key is global-based. •Neighbor—Key is neighbor-based. •Interface—Key is interface-based. •Chain—Key is part of a keychain. |
The following sample output shows detailed information about a Send mode SA that is followed by a Receive mode SA:
RP/0/RP0/CPU0:router# show rsvp authentication detail
RSVP Authentication Information:
Destination Address: 3.0.0.2
Neighbour Address: 3.0.0.2
LifeTime left: 1305 (sec)
KeyType: Static Global KeyChain
TX Sequence: 5023969459702858020 (0x45b8b99b00000124)
Messages successfully authenticated: 245
Messages failed authentication: 0
Incomplete security association: 0
Missing INTEGRITY object: 0
Duplicate sequence number: 0
Out-of-range sequence number: 0
Invalid message format: 0
Table 54 describes the significant fields shown in the display.
Table 54 show rsvp authentication detail Field Descriptions
|
|
Source Address |
IP address of the sender. For Send mode, this is the local address (either the address of the Interface field or the local router ID). For Recv mode, this is the address of the RSVP neighbor. |
Destination Address |
IP address of the receiver. For Send mode, this is the address of the RSVP neighbor. For Recv mode, this is the local address (either the address of the Interface field or the local router ID). |
Neighbor Address |
IP address of the RSVP neighbor with which the security association is being maintained. |
Interface |
Name of the interface over which the security association is being maintained. |
Direction |
Direction of the association for the following mode types: •Send—Authenticates messages that you forward. •Recv—Authenticates messages that you receive. |
LifeTime |
Configured expiration timer value. |
LifeTime left |
Number of seconds until the expiration timer expires. |
KeyType |
Lists the keys that are used: •Static—Key is static and configured. •Global—Key is global-based. •Neighbor—Key is neighbor-based. •Interface—Key is interface-based. •Chain—Key is part of a keychain. |
Key-Source |
Key source identification string that is currently set to the configured keychain name. |
Key Status |
Last status reported from the key source. |
Key-ID |
Last successful key ID that is used for authentication and that maps to the keychain ID configuration. If the value is too large to fit into the column, it is truncated and a (..) suffix is appended. (Use the detail mode to see the non-truncated key ID.) |
Digest |
Digest algorithm that is used. The algorithms are either HMAC-MD5 or HMAC-SHA1. |
Challenge |
Current challenge status (always Not supported) reported. |
Tx Sequence |
Last sequence number that was sent. |
RX Sequence |
Last accepted sequence number that was received. |
Messages successfully authenticated |
Number of messages authenticated by using this SA. |
Messages failed authentication |
Number of messages that failed authentication using this SA. |
Sequence Window Size |
Maximum configured RX sequence number window. |
Sequence Window Count |
Currently used size of the RX sequence number window. |
Sequence Window |
List of the last Sequence Window Count sequence numbers that were accepted. |
Incomplete security association |
Number of messages that are dropped due to a key failure. |
Incorrect digest |
Number of messages that are dropped due to an incorrect digest. |
Digest type mismatch |
Number of messages that are dropped due to an incorrect digest length, which implies an algorithm mismatch. |
Duplicate sequence number |
Number of messages that are dropped due to a duplicate sequence number. |
Out-of-range sequence number |
Number of messages that are dropped due to a sequence number range (window-size) checking. |
Invalid message format |
Number of messages that are dropped due to formatting errors, such as incorrect objects. |
show rsvp counters
To display internal RSVP counters, use the show rsvp counters command in EXEC mode.
show rsvp counters [messages type interface-path-id] [events | database]
Syntax Description
messages |
(Optional) Displays a historical count of the number of messages RSVP has received and sent on each interface along with a summation. |
type |
(Optional) Interface type. For more information, use the question mark (?) online help function. |
interface-path-id |
Physical interface or a virtual interface. Note Use the show interfaces command to see a list of all possible interfaces currently configured on the router. For more information about the syntax for the router, use the question mark (?) online help function. |
events |
(Optional) Displays the number of states expired for lack of refresh and a count of received NACKs. |
database |
(Optional) Displays counters on RSVP database, including number of paths, session, and so on. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The database keyword was added on both the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
In message counters, bundle messages are counted as single bundle messages. The component messages are not counted separately.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following is sample output from the show rsvp counters messages command for POS0/3/0/0:
RP/0/RP0/CPU0:router# show rsvp counters messages POS 0/3/0/0
POS0/3/0/0 Recv Xmit Recv Xmit
PathError 0 0 ResvError 0 0
PathTear 5 1 ResvTear 0 0
SRefresh 10118 0 OutOfOrder 0
Retransmit 0 Rate Limited 0
Table 55 describes the significant fields shown in the display.
Table 55 show rsvp counters messages Field Descriptions
|
|
Path |
Number of Path messages sent downstream or received from an upstream node. |
PathError |
Number of Path Error messages received from a downstream neighbor or sent to an upstream neighbor. |
PathTear |
Number of Path Tear messages sent downstream, or messages received, from upstream neighbors. |
ResvConfirm |
Number of ResvConfirm messages received from an upstream neighbor or sent to a downstream neighbor. |
Bundle |
Number of bundle messages containing RSVP messages sent and received by the neighbor. |
SRefresh |
Number of summary refresh messages sent to and received by a neighbor to refresh the path and reservation states. |
Retransmit |
Number of messages retransmitted to ensure reliable messaging (related to refresh reduction). |
Resv |
Number of reservation messages received from a downstream neighbor or sent to an upstream neighbor to reserve resources. |
ResvError |
Number of reservation error messages received from a upstream neighbor or sent to a downstream neighbor. |
ResvTear |
Number of reservation tear messages received from a downstream neighbor or sent to an upstream neighbor to tear down RSVP flows. |
Ack |
Number of acknowledgement messages sent and received by a neighbor acknowledging receipt of a message. |
Hello |
Number of hello messages sent to and received by a neighbor. |
OutOfOrder |
Number of messages received that are out of order. |
Rate Limited |
Number of RSVP packets affected by rate limiting. |
The following is sample output from the show rsvp counters events command:
RP/0/RP0/CPU0:router# show rsvp counters events
Expired Path states 0 Expired Path states 0
Expired Resv states 0 Expired Resv states 0
NACKs received 0 NACKs received 0
Expired Path states 0 Expired Path states 0
Expired Resv states 0 Expired Resv states 0
NACKs received 0 NACKs received 0
POS0/3/0/3 All RSVP Interfaces
Expired Path states 0 Expired Path states 0
Expired Resv states 0 Expired Resv states 0
NACKs received 0 NACKs received 0
Table 56 describes the significant fields shown in the display.
Table 56 show rsvp counters events Field Descriptions
|
|
Expired Path states |
Number of Path states expired for lack of refresh. |
Expired Reserve states |
Number of Resv states expired for lack of refresh. |
NACKS received |
Number of NACKS received. |
The following is sample output from the show rsvp counters database command:
RP/0/RP0/CPU0:router# show rsvp counters database
Locally created and incoming paths: 0
Locally created and incoming Reservations: 0
Table 57 describes the significant fields shown in the display.
Table 57 show rsvp counters database Field Descriptions
|
|
Sessions |
RSVP sessions. |
Locally created and incoming paths |
Path states created by a: •local application on the node, or •Path message received from the network |
Outgoing paths |
Outgoing path states. |
Locally created and incoming Reservations |
Reservations created by a: •Local application on the node, or •Path message received from the network |
Outgoing Reservations |
Outgoing reservation (request) states. |
Interfaces |
Known RSVP interfaces. |
show rsvp counters oor
To display internal RSVP counters on out of resources (OOR) events, use the show rsvp counters oor command in EXEC mode.
show rsvp counters oor [type interface-path-id | summary]
Syntax Description
type |
(Optional) Interface type. For more information, use the question mark (?) online help function. |
interface-path-id |
Physical interface or a virtual interface. Note Use the show interfaces command to see a list of all possible interfaces currently configured on the router. For more information about the syntax for the router, use the question mark (?) online help function. |
summary |
(Optional) Displays a summary of OOR events. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 3.2 |
This command was introduced on the Cisco CRS-1 and the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following is sample output from the show rsvp counters oor command:
RP/0/RP0/CPU0:router# show rsvp counters oor
All RSVP Interfaces Rejected
Table 58 describes the significant fields shown in the display.
Table 58 show rsvp counters oor Field Descriptions
|
|
Path |
Number of Path messages received on the interface that were rejected due to oor conditions. |
show rsvp counters prefix filtering
To display internal prefix-filtering related RSVP counters, use the show rsvp counters prefix-filtering command in EXEC mode.
show rsvp counters prefix-filtering {interface [type interface-path-id | summary]} {access-list [aclname]}
Syntax Description
interface |
Displays RSVP prefix-filtering counters for all interfaces. |
type |
(Optional) Interface type. For more information, use the question mark (?) online help function. |
interface-path-id |
Physical interface or a virtual interface. Note Use the show interfaces command to see a list of all possible interfaces currently configured on the router. For more information about the syntax for the router, use the question mark (?) online help function. |
summary |
(Optional) Displays a summary of RSVP prefix-filtering counters on all interfaces. |
access-list |
(Optional) Displays RSVP prefix-filtering counters for the access control list. |
aclname |
Name of the access control list. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 3.2 |
This command was introduced on the Cisco CRS-1 and the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Note Counters do not increment if you have not configured an access control list for prefix-filtering.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following is sample output from the show rsvp counters prefix filtering command:
RP/0/RP0/CPU0:router# show rsvp counters prefix-filtering interface
Routed Fwd Local Drop Def-Drop Def-Proc Total
POS0/5/0/1 Fwd Local Drop Def-Drop Def-Proc Total
POS0/5/0/2 Fwd Local Drop Def-Drop Def-Proc Total
Interfaces Fwd Local Drop Def-Drop Def-Proc Total
The following is sample output from the show rsvp counters prefix filtering interface type interface-path-id command:
RP/0/RP0/CPU0:router# show rsvp counters prefix-filtering interface POS 0/5/0/1
POS0/5/0/1 Fwd Local Drop Def-Drop Def-Proc Total
The following is sample output from the show rsvp counters prefix filtering summary command:
RP/0/RP0/CPU0:router# show rsvp counters prefix-filtering interface summary
Interfaces Fwd Local Drop Def-Drop Def-Proc Total
RP/0/RP0/CPU0:router# show rsvp counters prefix-filtering access-list
ACL: banks Forward Local Drop Total
RP/0/RP0/CPU0:router# show rsvp counters prefix-filtering access-list banks
ACL: banks Forward Local Drop Total
Table 59 describes the significant fields shown in the display.
Table 59 show rsvp counters prefix filtering interface and summary Field Descriptions
|
|
Fwd |
Number of messages forwarded to the next router. Note Because RSVP does not know what interface the messages will be forwarded, the messages are counted against the routed interface only. |
Local |
Number of messages not forwarded (because locally destined). |
Drop |
Number of messages dropped. |
Def-Drop |
Number of messages dropped when an access control list match returns an implicit deny. (Results when RSVP is configured to drop implicit deny messages.) |
Def-Proc |
Number of messages processed by RSVP when an access control list match returns an implicit deny. |
Path |
Number of Path messages. |
PathTear |
Number of Path Tear messages. |
ResvConfirm |
Number of ResvConfirm messages. |
show rsvp fast-reroute
To display RSVP Fast-Reroute (FRR) information, use the show rsvp counters fast-reroute command in EXEC mode.
show rsvp fast-reroute [destination A.B.C.D | dst-port destination port | source A.B.C.D | src-port source port | summary]
Syntax Description
destination A.B.C.D |
(Optional) Displays the IP address of the destination network. |
dst-port destination port |
(Optional) Displays the port address of the destination router. |
source A.B.C.D |
(Optional) Displays the IP address of the source network. |
src-port source port |
(Optional) Displays the port number of the source router. |
summary |
(Optional) Displays summarized information about the FRR database. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 3.2 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following is sample output from the show rsvp fast-reroute command:
RP/0/RP0/CPU0:router# show rsvp fast-reroute
Type Destination TunID Source PSBs RSBs
-------- --------------- ----------- ------------ --------- -------
LSP4 70.70.70.70 1 50.50.50.50 Ready Ready
Table 60 describes the significant fields shown in the display.
Table 60 show rsvp fast-reroute Field Descriptions
|
|
Type |
Type of session. |
Destination |
Destination address of session. |
TunID |
Tunnel ID number. |
Source |
Source address of session. |
PSBs |
PSB FRR1 state. |
RSBs |
RSB FRR state. |
The following is sample output from the show rsvp fast-reroute summary command:
RP/0/RP0/CPU0:router# show rsvp fast-reroute summary
States Total Ready Act-Wait Active
Table 61 describes the significant fields shown in the display.
Table 61 show rsvp fast-reroute summary Field Descriptions
|
|
States |
FRR1 state. |
Total |
Total number of path and reservation states. |
Ready |
Number of states in FRR ready state. No FRR processing has been done on these states. |
Act-Wait |
Number of states in "Active Wait" FRR state. •For PSBs, this indicates that after FRR the path message has not yet been sent. •For RSBs, this indicates that after FRR, the reservation message has not yet been received. |
Active |
Number of states in "Active" FRR state. •For PSBs, this indicates that after FRR the path message has been sent. •For RSBs, this indicates that after FRR, the reservation message has been received. |
show rsvp graceful-restart
To display the local graceful-restart information for RSVP, use the show rsvp graceful-restart command in EXEC mode.
show rsvp graceful-restart [neighbors A.B.C.D | detail]
Syntax Description
neighbors |
(Optional) Displays single-line status for each neighbor. If this keyword is not specified, only a multiline table entry is displayed showing local graceful-restart information. |
A.B.C.D |
(Optional) Address of the neighbor you are displaying. Displays a specific neighbor with that destination address only. If this keyword is not specified, all neighbors are displayed. |
detail |
(Optional) Displays multiline status for each neighbor. If this keyword is not specified, only a single-line table entry is displayed. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Graceful-restart neighbors are displayed in ascending order of neighbor IP address.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following is sample output from the show rsvp graceful-restart command:
RP/0/RP0/CPU0:router# show rsvp graceful-restart
Graceful restart: enabled Number of global neighbors: 1
Local MPLS router id: 192.168.55.55
Restart time: 60 seconds Recovery time: 120 seconds
Recovery timer: Not running
Hello interval: 5000 milliseconds Maximum Hello miss-count: 4
Table 62 describes the significant fields shown in the display.
Table 62 show rsvp graceful-restart Field Descriptions
|
|
Graceful restart |
Indicates whether graceful restart is configured locally. |
Number of global neighbors |
Number of neighbors identified by a unique router ID. |
Local router id |
Local router ID used for the MPLS or OUNI applications. |
Restart time |
Amount of time after a loss in hello messages within which RSVP hello session is reestablished. This setting is manually configurable. |
Recovery time |
Local recovery time advertised to neighbors. This is dynamically computed based on the number of LSPs established and is the time used by neighbors to refresh states in the event of a failure. |
Recovery timer |
A countdown timer which, upon expiry, causes un-refreshed data forwarding states to be deleted (usually beginning with a value that is equivalent to the sum of the restart and recovery times). |
Hello interval |
Interval at which hello messages are sent to neighbors. |
Maximum hello miss-count |
Number of hellos from a neighbor that can be missed before declaring hellos down. |
The following is sample output from the show rsvp graceful-restart neighbors command, which displays information about graceful restart neighbors in the router:
RP/0/RP0/CPU0:router# show rsvp graceful-restart neighbors
Neighbor App State Recovery Reason Since LostCnt
--------------- ----- ------ -------- ------------ -------------------- --------
192.168.77.77 MPLS UP DONE N/A 19/12/2002 17:02:25 0
Table 63 describes the significant fields shown in the display.
Table 63 show rsvp graceful-restart neighbors Field Descriptions
|
|
Neighbor |
Router ID of a global neighbor. |
App |
Application type of a global neighbor (MPLS or OUNI). |
State |
State of the hello session to a global neighbor (up, down, INIT). |
Recovery |
The state at which the local node is recovering a global neighbor. |
Reason |
The last reason for which communication has been lost for a global neighbor. If none has occurred, this field is marked as N/A. |
Since |
The time at which the current hello state for a global neighbor has been established. |
LostCnt |
Number of times hello communication has been lost with a global neighbor. |
The following is sample output from the show rsvp graceful-restart neighbors detail command, which displays detailed information about all graceful restart neighbors:
RP/0/RP0/CPU0:router# show rsvp graceful-restart neighbors detail
Neighbor: 192.168.77.77 Source: 192.168.55.55 (MPLS)
Hello instance for application MPLS
Hello State: UP (for 00:20:52)
Number of times communications with neighbor lost: 0
Number of Interface neighbors: 1
Restart time: 120 seconds Recovery time: 120 seconds
Restart timer: Not running
Recovery timer: Not running
Hello interval: 5000 milliseconds Maximum allowed missed Hello messages: 4
Table 64 describes the significant fields shown in the display.
Table 64 show rsvp graceful-restart neighbors detail Field Descriptions
|
|
Neighbor |
Router ID of a global neighbor. |
Source |
Local router ID and application type. |
Hello State |
State of the hello instance for the global neighbor (up, down, or init) and duration of the current state. |
Number of times communications with neighbor lost |
Number of times hello communication has been lost with a global neighbor. |
Reason |
Last reason indicating why communication was lost for a global neighbor. If none has occurred, this field is marked as N/A. |
Recovery State |
State at which the local node is recovering a global neighbor. |
Number of Interface neighbors |
Number of interfaces belonging to a global neighbor. |
Address |
IP address of the interface neighbor. |
Recovery time |
Remote recovery time for a global neighbor. |
Hello interval |
Interval at which hello messages are sent by the remote global neighbor. |
Maximum allowed missed Hello messages |
Number of hellos that can be missed by the remote global neighbor before declaring hellos down. |
show rsvp hello instance
To display the RSVP hello instances, use the show rsvp hello instance command in EXEC mode.
show rsvp hello instance [Hostname or A.B.C.D | detail]
Syntax Description
Hostname or A.B.C.D |
(Optional) Address of the neighbor you are displaying. If this argument is not specified, all neighbors are displayed. |
detail |
(Optional) Displays multiline status for each hello instance. If this keyword is not specified, only a single-line table entry is displayed. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Hello instances are displayed in ascending order of neighbor IP address.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following is sample output from the show rsvp hello instance command, which displays brief information about all hello instances in the router:
RP/0/RP0/CPU0:router# show rsvp hello instance
Neighbor Type State Interface LostCnt
---------------- ------ -------- ------------ --------
192.168.77.77 ACTIVE UP None 0
Table 65 describes the significant fields shown in the display.
Table 65 show rsvp hello instance Field Descriptions
|
|
Neighbor |
Router ID of a global neighbor hosting the hello instance. |
Type |
Hello instance type (active or passive). active type indicates that a node is sending hello requests and passive indicates that a node is sending hello acknowledgements. |
State |
State of the hello session to a global neighbor (up, down, or init). |
Interface |
Interface for interface bound hello's used for FRR1 . Hello instances bound to a global neighbor show Interface as None. Hello's used for FRR are currently not supported. |
LostCnt |
Number of times hello communication has been lost with a global neighbor. |
The following is sample output from the show rsvp hello instance command, which displays detailed information about all hello instances in the router:
RP/0/RP0/CPU0:router# show rsvp hello instance detail
Neighbor: 192.168.77.77 Source: 192.168.55.55 (MPLS)
Type: ACTIVE (sending requests)
Hello interval (msec) (used when ACTIVE)
Src_instance 0x484b01, Dst_instance 0x4d4247
Communication with neighbor lost:
Neighbor disabled Hello: 0
Table 66 describes the significant fields shown in the display.
Table 66 show rsvp hello instance detail Field Descriptions
|
|
Neighbor |
Router ID of a global neighbor. |
Source |
Local router ID and application type. |
State |
State of the hello instance for the global neighbor (up, down or init) and duration of the current state. |
Type |
Hello instance type (active or passive). active type indicates that a node is sending hello requests and passive indicates that a node is sending hello acks. |
I/F |
Interface for interface bound hello's. Hello instances for Graceful restart show interface as None. |
show rsvp hello instance interface-based
To display the RSVP hello instances on a specific interface, use the show rsvp hello instance interface-based command in EXEC mode.
show rsvp hello instance interface-based [A.B.C.D | detail]
Syntax Description
A.B.C.D |
(Optional) Address of the neighboring interface. you are displaying. If this argument is not specified, all neighbors are displayed. |
detail |
(Optional) Displays detailed information for the specified interface. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Hello instances are displayed in ascending order of neighbor IP address.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following is sample output from the show rsvp hello instance interface-based command, which displays detailed information about hello instances on a specific interface:
RP/0/RP0/CPU0:router# show rsvp hello instance interface-based 10.10.10.10
Neighbor Type State Interface LostCnt
---------------- ------ -------- ------------ --------
10.10.10.10 ACTIVE UP None 0
Table 67 describes the significant fields shown in the display.
Table 67 show rsvp hello instance Field Descriptions
|
|
Neighbor |
Router ID of a global neighbor hosting the hello instance. |
Type |
Hello instance type (active or passive). active type indicates that a node is sending hello requests and passive indicates that a node is sending hello acknowledgements. |
State |
State of the hello session to a global neighbor (up, down, or init). |
Interface |
Interface for interface bound hello's used for FRR1 . Hello instances bound to a global neighbor show Interface as None. Hello's used for FRR are currently not supported. |
LostCnt |
Number of times hello communication has been lost with a global neighbor. |
show rsvp interface
To display information about all interfaces with RSVP enabled, use the show rsvp interface command in EXEC mode.
show rsvp interface [type interface-path-id] [detail]
Syntax Description
type |
(Optional) Interface type. For more information, use the question mark (?) online help function. |
interface-path-id |
Physical interface or a virtual interface. Note Use the show interface command to see a list of all possible interfaces currently configured on the router. For more information about the syntax for the router, use the question mark (?) online help function. |
detail |
(Optional) Displays multiline status for each interface. If this keyword is not specified, only a single-line table entry is displayed. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Release 3.8.4 |
The following enhancements were added to the sample output to display RSVP bandwidth as a percentage: •Configured percentages are displayed if applicable. •The applicable interfaces are flagged that are using the RSVP bandwidth as a percentage as opposed to the absolute bandwidth. •A header line is displayed to indicate that the per pool percentages are used. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rsvp interface command to display various configuration settings such as the list of neighbors and their refresh reduction capabilities.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following is sample output from the show rsvp interface command, which displays brief information about RSVP-configured interfaces running in prestandard DS-TE mode.
RP/0/RP0/CPU0:router# show rsvp interface
*: Default I/F B/W % {RDM}: 90% (max reservable), 90% (bc0), 50% (bc1)
Interface MaxBW (bps) MaxFlow (bps) Allocated (bps) MaxSub (bps)
----------- ------------------ -------------------- -------------------- --------
PO0/4/0/0 10M 10M 1M ( 10%) 0
PO0/4/0/1 139968K* 116640K 0 ( 0%) 77760K*
Gi0/5/0/0 10M 10M 0 ( 0%) 0
Gi0/5/0/1 10M 10M 0 ( 0%) 0
This following is sample output from the show rsvp interface detail command running in standard DS-TE mode:
RP/0/RP0/CPU0:router# show rsvp interface pos 0/4/0/1 detail
*: Default I/F B/W % {RDM}: 90% (max reservable), 90% (bc0), 50% (bc1) INTERFACE:
POS0/4/0/1 (ifh=0x5000600).
VRF ID: 0x60000000 (Default).
BW (bits/sec): Max=139968K*. MaxFlow=116640K.
Allocated=0 (0%). MaxSub=77760K*.
Signalling: No DSCP marking. No rate limiting.
States in: 0. Max missed msgs: 4.
Expiry timer: Not running. Refresh interval: 45s.
Normal Refresh timer: Not running. Summary refresh timer: Not running.
Refresh reduction local: Enabled. Summary Refresh: Enabled (4096 bytes max).
Reliable summary refresh: Disabled. Bundling: Enabled. (4096 bytes max).
Ack hold: 400 ms, Ack max size: 4096 bytes. Retransmit: 900ms.
Related Commands
show rsvp neighbor
To display information about RSVP neighbors, use the show rsvp neighbor command in EXEC mode.
show rsvp neighbor [detail]
Syntax Description
detail |
(Optional) Displays detailed information about RSVP neighbors. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 3.3 |
This command was introduced on the Cisco CRS-1. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show rsvp interface command to display various configuration settings such as the list of neighbors and their refresh reduction capabilities.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following is sample output from the show rsvp neighbor command using the detail keyword:
RP/0/RP0/CPU0:router# show rsvp neighbor detail
Global Neighbor: 40.40.40.40
Interface Neighbor: 1.1.1.1
Refresh Reduction: "Enabled" or "Disabled".
Retransmitted messages: 0
Interface Neighbor: 2.2.2.2
Refresh Reduction: "Enabled" or "Disabled".
Retransmitted messages: 0
show rsvp request
To list all the requests that RSVP knows about on a router, use the show rsvp request command in EXEC mode.
show rsvp request [detail] [destination A.B.C.D | dst-port port-num | source A.B.C.D | src-port port-num]
Syntax Description
detail |
(Optional) Displays multiline status for each path. If this keyword is not specified, only a single-line table entry is displayed. |
destination A.B.C.D |
(Optional) Displays destination address information. |
dst-port port-num |
(Optional) Displays destination port and tunnel information. |
source A.B.C.D |
(Optional) Displays source address information. |
src-port port-num |
(Optional) Displays port and LSP ID information. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
This command displays information about upstream reservations only; that is, reservations being sent to upstream hops. Information about downstream reservations (that is, incoming or locally created reservations) is available using the show rsvp reservation command.
Reservations are displayed in ascending order of destination IP address, destination port, source IP address, and source port.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following is sample output from the show rsvp request command:
RP/0/RP0/CPU0:router# show rsvp request
Dest Addr DPort Source Addr SPort Pro OutputIF Sty Serv Rate Burst
---------------- ----- ---------------- ----- --- ---------- --- ---- ---- -----
192.168.40.40 2001 192.168.67.68 2 0 PO0/7/0/1 SE LOAD 0 1K
The following is sample output from the show rsvp request detail command, which displays detailed information about all requests in the router. Requests are reservation states for the reservation messages sent upstream:
RP/0/RP0/CPU0:router# show rsvp request detail
REQ: IPv4-LSP Session addr: 192.168.40.40. TunID: 2001. LSPId: 2.
Source addr: 192.168.67.68. ExtID: 192.168.67.68.
Output interface: POS0/7/0/1. Next hop: 192.168.67.68 (lih: 0x19700001).
Style: Shared-Explicit. Service: Controlled-Load.
Rate: 0 bits/sec. Burst: 1K bytes. Peak: 0 bits/sec.
MTU min: 0, max: 500 bytes.
Policy: Forwarding. Policy source(s): MPLS/TE.
Number of supporting PSBs: 1
Destination Add DPort Source Add SPort Pro Input IF Rate Burst Prot
192.168.40.40 2001 192.168.67.68 2 0 PO0/7/0/1 0 1K Off
Number of supporting RSBs: 1
Destination Add DPort Source Add SPort Pro Input IF Sty Serv Rate Burst
192.168.40.40 2001 65.66.67.68 2 0 None SE LOAD 0 1K
Table 68 describes the significant fields shown in the display.
Table 68 show rsvp request detail Field Descriptions
|
|
Number of supporting PSBs |
Number of senders for this session (typically, 1). |
Number of supporting RSBs |
Number of reservations per session (typically, 1). |
Policy |
Admission control status. |
Policy source |
Entity performing the admission control (MPLS-TE or COPS). |
Related Commands
show rsvp reservation
To display all reservations that RSVP knows about on a router, use the show rsvp reservation command in EXEC mode.
show rsvp reservation [detail] [destination A.B.C.D | dst-port port-num | source A.B.C.D | src-port port-num]
Syntax Description
detail |
(Optional) Displays multiline status for each reservation. If the detail keyword is not specified, only a single-line table entry is displayed. |
destination A.B.C.D |
(Optional) Displays destination address information. |
dst-port port-num |
(Optional) Displays destination port and tunnel ID information. |
source A.B.C.D |
(Optional) Displays source address information. |
src-port port-num |
(Optional) Displays source port and LSP ID information. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The show rsvp reservation command displays information about downstream reservations only (that is, reservations received on this device or created by application program interface (API) calls). Upstream reservations or requests are displayed using the show rsvp request command.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following is sample output from the show rsvp reservation command:
cRP/0/RP0/CPU0:router# show rsvp reservation
Dest Addr DPort Source Addr SPort Pro Input IF Sty Serv Rate Burst
---------------- ----- ---------------- ----- --- ---------- --- ---- ---- -----
192.168.40.40 2001 192.168.67.68 2 0 None SE LOAD 0 1K
192.168.67.68 2000 10.40.40.40 15 0 PO0/7/0/1 SE LOAD 0 1K
The following example displays detailed information about all reservations in the router:
RP/0/RP0/CPU0:router# show rsvp reservation detail
RESV: IPv4-LSP Session addr: 192.168.40.40. TunID: 2001. LSPId: 2.
Source addr: 192.168.67.68. ExtID: 192.168.67.68.
Input adjusted interface: None. Input physical interface: None.
Next hop: 0.0.0.0 (lih: 0x0).
Style: Shared-Explicit. Service: Controlled-Load.
Rate: 0 bits/sec. Burst: 1K bytes. Peak: 0 bits/sec.
MTU min: 40, max: 500 bytes.
State expires in 0.000 sec.
Policy: Accepted. Policy source(s): MPLS/TE.
Header info: RSVP TTL=255. IP TTL=255. Flags: 0x0. TOS=0xff.
Labels: Local downstream: 3.
RESV: IPv4-LSP Session addr: 192.168.67.68. TunID: 2000. LSPId: 15.
Source addr: 192.168.40.40. ExtID: 10.10.40.40.
Input adjusted interface: PO0/7/0/1. Input physical interface: PO0/7/0/1.
Next hop: 10.66.67.68 (lih: 0x8DE00002).
Style: Shared-Explicit. Service: Controlled-Load.
Rate: 0 bits/sec. Burst: 1K bytes. Peak: 0 bits/sec.
MTU min: 0, max: 500 bytes.
State expires in 361.184 sec.
Policy: Accepted. Policy source(s): MPLS/TE.
Header info: RSVP TTL=254. IP TTL=254. Flags: 0x1. TOS=0xff.
Labels: Outgoing downstream: 3.
Table 69 describes the significant fields shown in the display.
Table 69 show rsvp reservation detail Field Descriptions
|
|
Input adjusted interface |
Interface to reflect the path's outgoing interface. |
Input physical interface |
Interface where the reservation was received. |
Next hop |
Address of the downstream node that sent the reservation to this node. |
Lih |
Logical interface handle sent in the hop object of path returned to us in the reservation to figure out what interface the path was sent on. |
Flags |
Indicates path state, including as Local Repair, Local Sender (LSP1 ingress node), and others. |
Policy |
Admission control status. |
Policy source |
Entity performing the admission control on the LSP. |
Header info |
RSVP header information as described in RFC 2205. |
Related Commands
show rsvp sender
To display all path states that RSVP knows about on this router, use the show rsvp sender command in EXEC mode.
show rsvp sender [detail] [destination A.B.C.D | dst-port port-num | source A.B.C.D | src-port port-num]
Syntax Description
detail |
(Optional) Displays multiline status for each path. If the detail keyword is not specified, only a single-line table entry is displayed. |
destination A.B.C.D |
(Optional) Displays destination address information. |
dst-port port-num |
(Optional) Displays destination port and tunnel ID information. |
source A.B.C.D |
(Optional) Displays source address information. |
src-port port-num |
(Optional) Displays source port and LSP ID information. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The show rsvp sender command displays information about path states.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following is sample output from the show rsvp sender command:
RP/0/RP0/CPU0:router# show rsvp sender
Dest Addr DPort Source Addr SPort Pro Input IF Rate Burst Prot
---------------- ----- ---------------- ----- --- ------------ ---- ----- ----
10.40.40.40 2001 10.66.67.68 2 0 PO0/7/0/1 0 1K Off
10.66.67.68 2000 10.40.40.40 15 0 None 0 1K Off
Table 70 describes the significant fields shown in the display.
Table 70 show rsvp sender Field Descriptions
|
|
DProt |
Destination port number and tunnel-id. |
Dest Address |
Destination and session address of LSP1 . |
SPort |
Source port and LSP ID. |
Source Addr |
Address of the ingress node of the LSP. |
Input IF |
Interface on which the Path message was received. |
The following example displays detailed information about all paths in the system:
RP/0/RP0/CPU0:router# show rsvp sender detail
PATH: IPv4-LSP Session addr: 65.66.67.68. TunID: 1. LSPId: 25.
Source addr: 40.40.40.40. ExtID: 40.40.40.40.
Prot: Off. Backup tunnel: None.
Setup Priority: 7, Reservation Priority: 0
Rate: 0 bits/sec. Burst: 1K bytes. Peak: 0 bits/sec.
Min unit: 40 bytes, Max unit: 500 bytes
State expires in 370.154 sec.
Policy: Accepted. Policy source(s): Default.
Header info: RSVP TTL=254. IP TTL=254. Flags: 0x1. TOS=0xc0.
Input interface: PO0/3/0/0. Previous hop: 40.40.40.40 (lih: 0x40600001).
Labels: Outgoing upstream: 3.
Explicit Route (Incoming):
Strict, 65.66.67.68(interface-path-id 5)
Table 71 describes the significant fields shown in the display.
Table 71 show rsvp sender detail Field Descriptions
|
|
Prot |
LSP configured as a protected tunnel. |
Backup tunnel |
Name of the backup tunnel assigned to protect this LSP1 . |
Flags |
Path state, including as local repair, local sender (LSP ingress node), and others. |
Policy |
Admission control status for Path message in the incoming direction. |
Policy source |
Entity doing the admission control, such as COPS or MPLS-TE2 . |
Header info |
RSVP header information as described in RFC 2205. |
Input interface |
Interface on which the path was received. At ingress mode, it is None. |
Previous hop |
Address of the upstream peer who sent us the Path message. May be the interface address or node-id depending on LSP (packet or optical). |
Lih |
Logical interface handle received in the hop object of the path. |
Output interface |
Interface on which the path was forwarded to the downstream neighbor |
Policy |
Admission control status for the path in the outgoing direction. |
Explicit route |
Explicit route specified in the explicit-route object of the Path message. |
show rsvp session
To list all sessions that RSVP knows about on this router, use the show rsvp session command in EXEC mode.
show rsvp session [detail] [destination A.B.C.D | dst-port port-num | tunnel-name tunnel-name]
Syntax Description
detail |
(Optional) Displays multiline status for each path. If the detail keyword is not specified, only a single-line table entry is displayed. |
destination A.B.C.D |
(Optional) Displays destination address information. |
dst-port port-num |
(Optional) Displays destination port and tunnel ID information. |
tunnel-name tunnel-name |
(Optional) Displays status for the session matching the specified tunnel-name. |
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Sessions are displayed in ascending order of destination IP address, destination port, and source IP address.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following is sample output from the show rsvp session command:
RP/0/RP0/CPU0:router# show rsvp session
Type Session Addr Port Proto/ExtTunID PSBs RSBs Reqs
---- --------------- ----- --------------- ----- ----- -----
LSP4 10.40.40.40 2001 10.66.67.68 1 1 1
LSP4 10.66.67.68 2000 10.40.40.40 1 1 0
Table 72 describes the significant fields shown in the display.
Table 72 show rsvp session Field Descriptions
|
|
Type |
Type of data flow (Traffic-Engineering LSP (LSP4), OUNI, or IPV4 session). |
Session Addr |
Destination address of the data packets and also tail of the LSP. |
Port |
Destination port or tunnel ID in case of TE and OUNI tunnels. |
Proto/ExtTunID |
Source address of TE and OUNI tunnels or protocol as in the case of IPV4 sessions. |
PSBs |
Number of path state blocks for this session. |
RSBs |
Number of reservation state blocks pertaining to incoming or local reservations for this session. |
Reqs |
Number of requests. State data structure representing reservations sent up-stream. |
The following is sample output for the show rsvp session detail command:
RP/0/RP0/CPU0:router# show rsvp session detail
SESSION: IPv4-LSP Addr: 65.66.67.68, TunID: 1, ExtID: 40.40.40.40
PSBs: 1, RSBs: 1, Requests: 0
InLabel: No intf, No label
Incoming Address: Unknown
Strict, 65.66.67.68(interface-path-id 5)
Tspec: avg rate=0, burst=1K, peak rate=0
FRR OutLabel: No intf, No label
Node-id 65.66.67.68, interface index 5
Fspec: avg rate=0, burst=1K, peak rate=0
Table 73 describes the significant fields shown in the display.
Table 73 show rsvp session detail Field Descriptions
|
|
TunID |
Tunnel identifier and the destination port of the LSP1 . |
ExtID |
Ingress node address of LSP. |
Tunnel Instance |
Source port of the LSP (with the ExtId forming the source parameters). |
Tunnel Name |
Name of the tunnel and LSP. |
InLabel |
Incoming interface and label info for the LSP in the upstream direction. At the egress node, using penultimate hop popping at the egress node, (implicit-null) appears as No Label. |
Incoming Address |
Address of the ingress interface. |
Explicit Route |
Explicit route specified in the explicit-route object of the Path message. |
Record Route |
Record route object in either the path or reservation message. |
Tspec |
Traffic parameters. |
OutLabel |
Outgoing interface and label sent downstream. |
FRR OutLabel |
For FRR2 , displays the backup tunnel and Merge-point label. |
Fspec |
Flow spec parameters for specified QoS. |
signalling dscp (RSVP)
To give all RSVP signaling packets sent out on a specific interface higher priority in the network by marking them with a particular Differentiated Service Code Point (DSCP), use the signalling dscp command in RSVP interface configuration submode. To return to the default behavior, use the no form of this command.
signalling dscp dscp
no signalling dscp
Syntax Description
dscp |
Specifies a DSCP priority number. Range is 0 to 63. |
Defaults
No default behavior or values
Command Modes
RSVP interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
DSCP marking improves signaling setup and teardown times.
Ordinarily, when a router receives Path messages for a particular state marked with a DSCP value, it sends out Path messages for that state marked with the same DSCP value. This command overrides that DSCP persistence and ensures that all messages sent out a particular interface are marked with a specified DSCP.
Though this command controls RSVP signaling packets, it has no effect on ordinary IP or MPLS data packets traveling along the path created or reserved by this RSVP session.
DSCP persistence operates on a per-state basis, but this command operates on a per-interface basis. So, if some incoming message (for example, multicast Path) with DSCP 10 causes two outgoing messages on interfaces A and B, ordinarily both are sent with DSCP 10. If signalling dscp 5 is configured for RSVP on interface A, the Path messages being sent out interface A is marked with DSCP 5, but the Path messages being sent out interface B are marked with DSCP 10.
There is a difference between the signalling dscp 0 and no signalling dscp commands. The first command instructs RSVP to explicitly set to 0 the DSCP on all packets sent out this interface. The second command removes any override on the packets being sent out this interface, and allows the DSCP of received packets that created this state to persist on packets forwarded out this interface.
The RFC specifies a standard mapping from the eight IP precedence values to eight values in the 64-value DSCP space. You can use those special DSCP values to specify IP precedence bits only.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to mark all RSVP packets going out on POS interface 0/1/0/1 as DSCP 20:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp interface pos 0/1/0/1
RP/0/RP0/CPU0:router(config-rsvp-if)# signalling dscp 20
The following example shows how to disable DSCP marking of signaling packets going out POS interface 0/1/0/1:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp interface pos 0/1/0/1
RP/0/RP0/CPU0:router(config-rsvp-if)# interface pos 0/1/0/1
RP/0/RP0/CPU0:router(config-rsvp-if)# no signalling dscp
signalling graceful-restart
To enable or disable RSVP signaling graceful restart, use the signalling graceful-restart command in RSVP configuration mode. To return to the default behavior, use the no form of this command.
signalling graceful-restart
no signalling graceful-restart
Syntax Description
This command has no arguments or keywords.
Defaults
RSVP signaling graceful restart is disabled.
Command Modes
RSVP configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The signalling graceful-restart command provides a mechanism that helps minimize the negative effects on MPLS and Optical User Network Interface (O-UNI) traffic for the following types of faults. This is an implementation of the fault handling section of the IETF standard RFC 3473:
•Control-channel-failure—Disruption of communication channels between 2 nodes when the communication channels are separated from the data channels.
•Node-failure—The control plane of a node fails, but the node preserves its data forwarding states.
The signalling graceful-restart command instigates the exchange of RSVP hello messages between the router and its neighbor nodes. After the hello messages are established with a given neighbor, RSVP can detect these types of faults when they occur.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to enable RSVP signalling graceful restart:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# configure rsvp
RP/0/RP0/CPU0:router(config-rsvp)# signalling graceful-restart
Related Commands
signalling graceful-restart restart-time
To configure the restart time that is advertised in the Restart Cap object in hello messages, use the signalling graceful-restart restart-time command in RSVP configuration mode. To return to the default behavior, use the no form of this command.
signalling graceful-restart restart-time time
no signalling graceful-restart restart-time
Syntax Description
time |
Time after a control-plane restart that RSVP can start exchanging hello messages. Range is 60 to 3600 seconds. Default is 120 seconds. |
Defaults
restart-time: 120 seconds
Command Modes
RSVP configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
If no hello messages are received from a neighbor within a certain number of hello intervals, a node assumes that communication with the neighbor has been lost. The node waits the amount of time advertised by the last restart time communicated by the neighbor, before invoking procedures for recovery from communication loss.
The configured restart time is important in case of recovery from failure. The configured value should accurately reflect the amount of time within which, after a control-plane restart, RSVP can start exchanging hello messages.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to set the restart time:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# configure rsvp
RP/0/RP0/CPU0:router(config-rsvp)# signalling graceful-restart restart-time 200
The following example shows how to reset the restart time to the default of 120 seconds:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# configure rsvp
RP/0/RP0/CPU0:router(config-rsvp)# no signalling graceful-restart restart-time
Related Commands
signalling hello graceful-restart interface-based
To enable RSVP to accept interface-based hello requests from the neighbor on an interface and send a Hello Ack to it, use the rsvp hello graceful-restart interface-based command in RSVP configuration mode. To return to the default behavior, use the no form of this command.
signalling hello graceful-restart interface-based
no signalling hello graceful-restart interface-based
Syntax Description
This command has no arguments or keywords.
Defaults
.No default behavior or values
Command Modes
RSVP interface configuration
Command History
|
|
Release 3.3 |
This command was introduced on the Cisco CRS-1. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to enable interface-based graceful restart:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# configure rsvp interface tunnel-te 66
RP/0/RP0/CPU0:router(config-rsvp-if)# signalling hello graceful-restart interface based
signalling hello graceful-restart refresh interval
To configure the interval at which RSVP graceful-restart hello messages are sent to each neighbor, use the signalling hello graceful-restart refresh interval command in global configuration mode. To return to the default behavior, use the no form of this command.
signalling hello graceful-restart refresh interval refresh-interval
no signalling hello graceful-restart refresh interval
Syntax Description
refresh-interval |
Interval at which RSVP graceful-restart hello messages are sent to each neighbor. Range is 3000 to 30000 milliseconds. |
Defaults
refresh interval: 5000 milliseconds
Command Modes
Global configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The signalling hello graceful-restart refresh interval command determines how often hello messages are sent to each neighbor. If the interval is made short, the hello messages are sent more frequently. Although a short interval may help detect failures quickly, it also results in increased network traffic. Optimizations in the RSVP hello mechanism exist to reduce the number of hello messages traveling over the network.
When an RSVP hello message is received, the receiving node acknowledges the hello and restarts its hello timer to the neighbor. By doing this, a hello is transmitted to the neighbor only if a hello is not received before the hello refresh interval has expired.
If two neighboring nodes do not have the same hello interval, the node with the larger hello interval has to acknowledge its neighbor's (more frequent) hellos. For instance, if node A has a hello interval of 5 seconds, and node B has a hello interval of 10 seconds, node B still has to send hello messages every 5 seconds.
The hello backoff mechanism is an optimization that is tailored to minimize the number of hello messages from a neighbor that either does not have graceful restart enabled, or that fails to come back up during the restart interval. The restart interval is provided by the neighbor in the restart cap object.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example sets the hello graceful-restart refresh interval to 4000 msecs:
RP/0/RP0/CPU0:router# config
RP/0/RP0/CPU0:router(config)# config rsvp
RP/0/RP0/CPU0:router(config-rsvp)# signalling hello graceful-restart refresh interval 4000
Related Commands
signalling hello graceful-restart refresh misses
To configure the number of consecutive missed RSVP hello messages before a neighbor is declared down or unreachable, use the signalling hello graceful-restart refresh misses command in RSVP configuration mode. To return to the default behavior, use the no form of this command.
signalling hello graceful-restart refresh misses refresh-misses
no signalling hello graceful-restart refresh misses
Syntax Description
refresh-misses |
The number of misses for hello messages before a neighbor is declared down or unreachable. Range is 1 to 10. Default is 3. |
Defaults
refresh-misses: 3
Command Modes
RSVP configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
If no hello messages (request or ACK) are received from a neighbor within the configured number of refresh misses, the node assumes that communication with the neighbor has been lost.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to set hello graceful-restart refresh misses to 4:
RP/0/RP0/CPU0:router# config
RP/0/RP0/CPU0:router(config)# config rsvp
RP/0/RP0/CPU0:router(config-rsvp)# signalling hello graceful-restart refresh misses 4
Related Commands
signalling prefix-filtering access-list
To specify the extended access control list to use for prefix filtering of RSVP Router Alert messages, use the signalling prefix-filtering access-list command in RSVP configuration mode. To return to the default behavior, use the no form of this command.
signalling prefix-filtering access-list access list name
no signalling prefix-filtering access-list access list name
Syntax Description
access list name |
Extended access-list name as a string (maximum 32 characters). |
Defaults
No default behavior or values
Command Modes
RSVP configuration
Command History
|
|
Release 3.2 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Note The extended access control list containing the source and destination prefixes used for packet filtering is configured separately.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to configure the access control list name banks for prefix-filtering of RSVP Router Alert messages:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# configure rsvp
RP/0/RP0/CPU0:router(config-rsvp)# signalling prefix-filtering access-list banks
The following example shows how to disable RSVP prefix-filtering of RSVP Router Alert messages:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# configure rsvp
RP/0/RP0/CPU0:router(config-rsvp)# no signalling prefix-filtering access-list banks
Related Commands
signalling prefix-filtering default-deny-action
To configure RSVP to drop RSVP Router Alert messages when an access control list match returns an implicit deny, use the signalling prefix-filtering default-deny-action command in RSVP configuration mode. To return to the default behavior, use the no form of this command.
signalling prefix-filtering default-deny-action drop
no signalling prefix-filtering default-deny-action drop
Syntax Description
drop |
Specifies when RSVP router alert messages are dropped. |
Defaults
Performs normal RSVP processing of Path, Path Tear, and ResvConfirm message packets.
Command Modes
RSVP configuration
Command History
|
|
Release 3.2 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to configure RSVP Router Alert messages when an access control list match returns an implicit deny:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# configure rsvp
RP/0/RP0/CPU0:router(config-rsvp)# signalling prefix-filtering default-deny-action drop
Related Commands
signalling rate-limit
To limit the rate of RSVP signaling messages being sent out a particular interface, use the signalling rate-limit command in RSVP interface configuration mode. To return to the default behavior, use the no form of this command.
signalling rate-limit [rate messages] [interval interval-length]
no signalling rate-limit [rate messages] [interval interval-length]
Syntax Description
rate messages |
(Optional) Configures the number of messages sent per scheduling interval. Range is 1 to 500 messages. |
interval interval-length |
(Optional) Specifies the length between scheduling intervals (specified in milliseconds). Range is 250 to 2000 milliseconds. |
Defaults
messages: 100
interval-length: 1 second
Command Modes
RSVP interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the rate-limiting feature with caution. Limiting the rate of RSVP signaling has the advantage of avoiding an overload of the next hop router's input queue, because such overloads would cause the next hop router to drop RSVP messages. However, reliable messaging and rapid retransmit usually enable the router to recover very rapidly from message drops; so rate limiting might not be necessary.
If the rate is set too low, it causes slower convergence times. This command limits all RSVP messages except acknowledgments (ACK) and SRefresh messages. The command does not let you make a router generate messages faster than its inherent limit. (That limit differs among router models.)
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to enable rate-limiting:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp interface POS0/3/0/0
RP/0/RP0/CPU0:router(config-rsvp-if)# signalling rate-limit
The following example shows how to limit the rate to 50 messages per second:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp interface pos 0/3/0/0
RP/0/RP0/CPU0:router(config-rsvp-if)# signalling rate-limit rate 50
The following example shows how to set a limit at 40 messages for every 250 milliseconds:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp interface pos 0/3/0/0
RP/0/RP0/CPU0:router(config-rsvp-if)# signalling rate-limit rate 40 interval 250
The following example shows how to restore the rate to the default of 100 messages per second:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp interface pos 0/3/0/0
RP/0/RP0/CPU0:router(config-rsvp-if)# no signalling rate-limit rate
The following example shows how to disable rate-limiting:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp interface pos 0/3/0/0
RP/0/RP0/CPU0:router(config-rsvp-if)# no signalling rate-limit
Related Commands
signalling refresh interval
To change the frequency with which a router updates the network about the RSVP state of a particular interface, use the signalling refresh interval command in RSVP interface configuration mode. To return to the default behavior, use the no form of this command.
signalling refresh interval seconds
no signalling refresh interval
Syntax Description
seconds |
Number of seconds the router waits to update the network about the RSVP state of an interface (specified in seconds). Range is 10 to 180 seconds. Default is 45 seconds. |
Defaults
seconds: 45
Command Modes
RSVP interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
RSVP relies on a soft-state mechanism to maintain state consistency in the face of network losses. That mechanism is based on continuous refresh messages to keep a state current. Each RSVP router is responsible for sending periodic refresh messages to its neighbors.
The router attempts to randomize network traffic and reduce metronomic burstiness by jittering the actual interval between refreshes by as much as 50 percent. As a result, refreshes may not be sent at exactly the interval specified. However, the average rate of refreshes are within the specified refresh interval.
Lengthening the interval reduces the refresh load of RSVP on the network but causes downstream nodes to hold state longer. This reduces the responsiveness of the network to failure scenarios. Shortening the interval improves network responsiveness but expands the messaging load on the network.
The reliable messaging extension, implemented through the signalling refresh reduction reliable command, may cause new or changed messages to be temporarily refreshed at a more rapid rate than specified, in order to improve network responsiveness.
The use of reliable messaging with rapid retransmit substantially improves network responsiveness in case of transient message loss; if the refresh interval is changed when using the reliable messaging feature, it is more useful to lengthen the interval than to shorten it.
The summary refresh extension, implemented through the signalling refresh reduction summary command, provides a lower-cost mechanism to refresh RSVP state. The router uses the same refresh interval between successive refreshes of a single state when using summary refresh and when using ordinary message-based refresh.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to specify a refresh interval of 30 seconds:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# configure rsvp interface tunnel-te 2
RP/0/RP0/CPU0:router(config-rsvp-if)# signalling refresh interval 30
The following example shows how to restore the refresh interval to the default value of 45 seconds:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# configure rsvp interface tunnel-te 2
RP/0/RP0/CPU0:router(config-rsvp-if)# no signalling refresh interval
Related Commands
signalling refresh missed
To specify the number of successive refresh messages that can be missed before the RSVP deems a state to be expired (resulting in the state to be torn down), use the signalling refresh missed command in RSVP interface configuration mode. To return to the default behavior, use the no form of this command.
signalling refresh missed number
no signalling refresh missed
Syntax Description
number |
Number of successive missed refresh messages. Range is 1 to 8. Default is 4. |
Defaults
number: 4
Command Modes
RSVP interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Decreasing the missed-message number improves RSVP responsiveness to major failures like router failure or link faults, but decreases the resilience of RSVP resulting in packet drops or temporary network congestion. The latter condition makes RSVP too sensitive.
Increasing the missed-message number increases the resilience of RSVP to such transient packet loss, but decreases the RSVP responsiveness to more intransient network failures such as router failure or link fault.
The default value of 4 provides a balance of resilience and responsiveness factors.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to specify a missed refresh limit of six (6) messages:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# configure rsvp interface tunnel-te 2
RP/0/RP0/CPU0:router(config-rsvp-if)# signalling refresh missed 6
The following example shows how to return the missed refresh limit to the default value of four (4):
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# configure rsvp interface tunnel-te 2
RP/0/RP0/CPU0:router(config-rsvp-if)# no signalling refresh missed
Related Commands
signalling refresh reduction bundle-max-size
To configure the maximum size of a single RSVP bundle message, use the signalling refresh reduction bundle-max-size command in RSVP interface configuration mode.
signalling refresh reduction bundle-max-size size
Syntax Description
size |
Maximum size of a single RSVP bundle message. Range is 512 to 65000 bytes. |
Defaults
size: 4096 bytes
Command Modes
RSVP interface configuration
Command History
|
|
Release 3.2 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to set the maximum bundle size of a single RSVP bundle message to 4000:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# configure rsvp interface tunnel-te 2
RP/0/RP0/CPU0:router(config-rsvp-if)# signalling refresh reduction bundle-max-size 4000
Related Commands
signalling refresh reduction disable
To disable RSVP refresh reduction on an interface, use the signalling refresh reduction disable command in RSVP interface configuration mode. To return to the default behavior, use the no form of this command.
signalling refresh reduction disable
no signalling refresh reduction disable
Syntax Description
This command has no arguments or keywords.
Defaults
No default behavior or values
Command Modes
RSVP interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The following features of the IETF refresh reduction standard RFC 2961 are enabled with this command:
•Setting the refresh-reduction-capable bit in message headers
•Message-ID usage
•Reliable messaging with rapid retransmit, acknowledgment (ACK), and NACK messages
•Summary refresh extension
Because refresh reduction relies on cooperation of the neighbor, the neighbor must also support the standard. If the router detects that a neighbor is not supporting the refresh reduction standard (either through observing the refresh-reduction-enabled bit in messages received from the next hop, or by sending a Message-ID object to the next hop and receiving an error), refresh reduction is not used on this link. That information is obtained through use of the show rsvp interface detail command.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to disable RSVP refresh reduction on an interface:
RP/0/RP0/CPU0:router(config-rsvp-if)# signalling refresh reduction disable
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# configure rsvp interface tunnel-te 2
The following example shows how to enable RSVP refresh reduction on the interface:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# configure rsvp interface tunnel-te 2
RP/0/RP0/CPU0:router(config-rsvp-if)# no signalling refresh reduction disable
Related Commands
signalling refresh reduction reliable
To configure the parameters of reliable messaging, use the signalling refresh reduction reliable command in RSVP interface configuration mode. To return to the default behavior, use the no form of this command.
signalling refresh reduction reliable [ack-max-size bytes | ack-hold-time milliseconds | retransmit-time milliseconds | summary-refresh]
no signalling refresh reduction reliable [ack-max-size bytes | ack-hold-time milliseconds | retransmit-time milliseconds | summary-refresh]
Syntax Description
ack-max-size |
(Optional) Specifies the maximum size of the RSVP component within a single acknowledgment message. |
bytes |
(Optional) Specifies the number of bytes that define the maximum size of an RSVP component. Range is 20 to 65000 bytes. |
ack-hold-time |
(Optional) Specifies the maximum amount of time a router holds an acknowledgment before sending it, in an attempt to bundle several acknowledgments into a single acknowledgment message. |
milliseconds |
(Optional) Specifies the number of milliseconds that define the acknowledgment hold time. Range is 100 to 5000 milliseconds. |
retransmit-time |
(Optional) Specifies the amount of time the router initially waits for an acknowledgment message before resending the RSVP message. |
milliseconds |
(Optional) Specifies the number of milliseconds that define the retransmit time. Range is 100 to 10000 milliseconds. |
summary-refresh |
(Optional) Enables the use of reliable transmission for RSVP summary refresh messages. |
Defaults
ack-max-size bytes: 4096
ack-hold-time milliseconds: 400 (0.4 seconds)
retransmit-time milliseconds: 900 (0.9 seconds)
Command Modes
RSVP interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
For reliable messaging to work properly, configure the retransmit time on the send router (A) and acknowledgment hold time on the peer router (B). (Vice versa for messages in reverse direction.)
The retransmit time must be greater than the acknowledgment hold time, so that the acknowledgment message has time to get back to the sender before the message retransmits. We recommend that the retransmit-time interval be at least twice the acknowledgment hold-time interval. If the retransmit-time value is smaller than the acknowledgment hold-time value, then router A retransmits the message even though router B may have received the message and is waiting for an acknowledgment hold time to time out to send the acknowledgment. This causes unnecessary network traffic.
Reducing the value of ack-max-size causes more acknowledgment messages to be issued, with fewer acknowledgments contained within each acknowledgment message. However, reducing the acknowledgment-max-size does not speed up the rate at which acknowledgment messages are issued, because their frequency is still controlled by the time values (acknowledgment hold time and retransmit time).
To use reliable messaging for summary refresh messages, use the rsvp interface interface-name signalling refresh reduction summary command.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to set the maximum acknowledgment message size to 4096 bytes on POS interface 0/4/0/1:
RP/0/RP0/CPU0:router(config)# rsvp interface pos 0/4/0/1
RP/0/RP0/CPU0:router(config-rsvp-if)# signalling refresh reduction reliable ack-max-size
4096
The following example shows how to return the maximum acknowledgment message size to the default of 1000 bytes on POS interface 0/4/0/1:
RP/0/RP0/CPU0:router(config)# rsvp interface pos 0/4/0/1
RP/0/RP0/CPU0:router(config-rsvp-if)# no rsvp signalling refresh reduction reliable
The following example shows how to set the acknowledgment hold time to 1 second:
RP/0/RP0/CPU0:router(config)# rsvp interface pos 0/4/0/1
RP/0/RP0/CPU0:router(config-rsvp-if)# signalling refresh reduction reliable
ack-hold-time 1000
The following example shows how to return the acknowledgment hold time to the default of 0.4 second:
RP/0/RP0/CPU0:router(config)# rsvp interface pos 0/4/0/1
RP/0/RP0/CPU0:router(config-rsvp-if)# no signalling refresh reduction reliable
ack-hold-time
The following example shows how to set the retransmit timer to 2 seconds:
RP/0/RP0/CPU0:router(config)# rsvp interface pos 0/4/0/1
RP/0/RP0/CPU0:router(config-rsvp-if)# signalling refresh reduction reliable
retransmit-time 2000
The following example shows how to return the retransmit timer to the default of 0.9 seconds:
RP/0/RP0/CPU0:router(config)# rsvp interface pos 0/4/0/1
RP/0/RP0/CPU0:router(config-rsvp-if)# no signalling refresh reduction reliable
The following example shows how to enable the use of reliable transmission for RSVP summary refresh messages:
RP/0/RP0/CPU0:router(config-rsvp-if)# signalling refresh reduction reliable
summary-refresh
The following example shows how to disable the use of reliable transmission for RSVP summary refresh messages:
RP/0/RP0/CPU0:router(config-rsvp-if)# no signalling refresh reduction reliable
summary-refresh
Related Commands
signalling refresh reduction summary
To configure RSVP summary refresh message size on an interface, use the signalling refresh reduction summary command in RSVP interface configuration mode. To return to the default behavior, use the no form of this command.
signalling refresh reduction summary [max-size bytes]
no signalling refresh reduction summary [max-size bytes]
Syntax Description
max-size bytes |
(Optional) Specifies the maximum size in bytes of a single RSVP summary refresh message. Range is 20 to 65000 bytes. |
Defaults
bytes: 4096
Command Modes
RSVP interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the signalling refresh reduction summary command to specify the maximum size of the summary refresh messages sent. Message size is verified using the show rsvp interface detail command.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to change the summary message maximum size on an interface:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# configure rsvp interface tunnel-te 2
RP/0/RP0/CPU0:router(config-rsvp-if)# signalling refresh reduction summary max-size 6000
The following example shows how to return the summary message maximum size to the default value on an interface:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# configure rsvp interface tunnel-te 2
RP/0/RP0/CPU0:router(config-rsvp-if)# no signalling refresh reduction summary max-size
6000
Related Commands
window-size (RSVP)
To specify the maximum number of RSVP authenticated messages that can be received out of sequence, use the window-size command in RSVP authentication configuration mode, RSVP interface authentication configuration mode, or RSVP neighbor authentication configuration mode. To disable the window size, use the no form of this command.
window-size {N}
no window-size
Syntax Description
N |
Size of the window to restrict out-of-sequence messages. Range is 1 to 64. Default is 1. All out-of-sequence messages are dropped. |
Defaults
N: 1
Command Modes
RSVP authentication configuration
RSVP interface authentication configuration
RSVP neighbor authentication configuration
Command History
|
|
Release 3.4.1 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the window-size command to specify the maximum number of authenticated messages that are received out of sequence. All RSVP authenticated messages include a sequence number that is used to prevent replays of RSVP messages.
With a default window size of one message, RSVP rejects any out-of-order or out-of-sequence authenticated messages, because they are assumed to be replay attacks. However, sometimes bursts of RSVP messages become reordered between RSVP neighbors. If this occurs on a regular basis, and you can verify that the node sending the burst of messages is trusted, you can use the window-size option to adjust the burst size such that RSVP does not discard such reordered bursts. RSVP checks for duplicate messages within these bursts.
|
|
mpls-te |
read, write |
ouni |
read, write |
Examples
The following example shows how to configure the size of the window to 33 in RSVP neighbor authentication configuration mode:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp neighbor 1.1.1.1 authentication
RP/0/RP0/CPU0:router(config-rsvp-nbor-auth)# window-size 33
The following example shows how to configure the size of the window to 33 in RSVP authentication configuration mode:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp authentication
RP/0/RP0/CPU0:router(config-rsvp-auth)# window-size 33
The following example shows how to configure the size of the window to 33 in RSVP interface authentication configuration mode by using the rsvp interface command:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# rsvp interface POS 0/2/1/0
RP/0/RP0/CPU0:router(config-rsvp-if)# authentication
RP/0/RP0/CPU0:router(config-rsvp-if-auth)# window-size 33
Related Commands
|
|
key-source key-chain (RSVP) |
Specifies the source of the key information to authenticate RSVP signaling messages. |
life-time (RSVP) |
Controls how long RSVP maintains idle security associations with other trusted RSVP neighbors. |