IS-IS Commands on Cisco IOS XR Software
This chapter describes the commands used to configure and monitor the Intermediate System-to-Intermediate System (IS-IS) protocol.
For detailed information about IS-IS concepts, configuration tasks, and examples, see Implementing IS-IS on Cisco IOS XR Software module in Cisco IOS XR Routing Configuration Guide.
address-family (IS-IS)
To enter address family configuration mode for configuring Intermediate System-to-Intermediate System (IS-IS) routing that use standard IP Version 4 (IPv4) and IP Version 6 (IPv6) address prefixes, use the address-family command in router configuration or interface configuration mode. To disable support for an address family, use the no form of this command.
address-family {ipv4 | ipv6} {unicast | mulitcast}
no address-family {ipv4 | ipv6} {unicast | multicast}
Syntax Description
ipv4 |
Specifies IPv4 address prefixes. |
ipv6 |
Specifies IPv6 address prefixes. |
unicast |
Specifies unicast address prefixes. |
multicast |
Specifies multicast address prefixes. |
Defaults
An address family is not specified. The default subaddress family (SAFI) is unicast.
Command Modes
Router configuration
Interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
The multicast keyword was added. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the address family command to place the router or interface in address family configuration mode. In router address family configuration mode, you can configure routing that uses standard IPv4 or IPv6 address prefixes. An address family must be specified in interface configuration mode. In interface address family configuration mode, you can alter interface parameters for IPv4 or IPv6.
An address family must be specified to configure parameters that pertain to a single address family.
Examples
The following example shows how to configure the IS-IS router process with IPv6 unicast address prefixes:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface gigabitEthernet 0/1/0/0
RP/0/RP0/CPU0:router(config-isis-if)# address-family ipv6 unicast
RP/0/RP0/CPU0:router(config-isis-if-af)#
address-family multicast topology (IS-IS)
To enable a multicast topology when configuring Intermediate System-to-Intermediate System (IS-IS) routing (or to place a given topology within the IS-IS interface), use the address-family multicast topology command with either IPv4 or IPv6 address prefix in the appropriate configuration mode. To disable support for a multicast topology in IS-IS, use the no form of this command.
address-family {ipv4 | ipv6} multicast topology topo-name [maximum prefix prefix-limit]
no address-family {ipv4 | ipv6} multicast topology topo-name
Syntax Description
ipv4 |
Specifies IPv4 address prefixes. |
ipv6 |
Specifies IPv6 address prefixes. |
multicast |
Specifies multicast address prefixes. |
topology topo-name |
Specifies the name of the topology. |
maximum prefix |
Specifies maximum number of prefixes that a routing table can have. |
prefix-limit |
32-2,000,000. |
Defaults
An address family for multicast topology is not specified. The default subaddress family (SAFI) is unicast.
Command Modes
Router configuration
Interface configuration
Command History
|
|
Release 3.7.0 |
This command was introduced on the Cisco XR 12000 Series Router. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the address family multicast topology command to place the router or interface in address family configuration mode. In router address family configuration mode, you can associate an IS-IS topology ID with the topology you have created to add connected and local routes to a specific routing table.
Examples
The following example shows how to configure the IS-IS router topology with an IPv6 multicast address prefix:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# address-family ipv6 multicast topology green
RP/0/RP0/CPU0:router(config-isis-af)#
or
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface gigabitethernet 0/3/0/0
RP/0/RP0/CPU0:router(config-isis-if)# address-family ipv6 multicast topology green
RP/0/RP0/CPU0:router(config-isis-if-af)#
Related Commands
|
|
topology-id |
Associates a topology ID with a named IS-IS topology to differentiate topologies in the domain. |
adjacency-check disable
To suppress Intermediate System-to-Intermediate System (IS-IS) IP Version 4 (IPv4) or IP Version 6 (IPv6) protocol-support consistency checks performed on hello packets, use the adjacency-check disable command in address family configuration mode. To remove this function, use the no form of this command.
adjacency-check disable
no adjacency-check disable
Syntax Description
This command has no arguments or keywords.
Defaults
Adjacency check is enabled in both address families.
Command Modes
Address family configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
IS-IS performs consistency checks on hello packets and forms an adjacency only with a neighboring router that supports the same set of protocols. A router running IS-IS for both IPv4 and IPv6 does not form an adjacency with a router running IS-IS for IPv4 only.
Use the adjacency-check disable command to suppress the consistency checks for IPv6 IS-IS and allow an IPv4 IS-IS router to form an adjacency with a router running IPv4 IS-IS and IPv6. IS-IS never forms an adjacency between a router running IPv4 IS-IS only and a router running IPv6 only.
In addition, the adjacency-check disable command suppresses the IPv4 or IPv6 subnet consistency check and allows IS-IS to form an adjacency with other routers regardless of whether they have an IPv4 or IPv6 subnet in common.
Examples
The following example shows how the network administrator introduces IPv6 into an existing IPv4 IS-IS network and ensures that the checking of hello packet checks from adjacent neighbors is disabled until all neighbor routers are configured to use IPv6:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# address-family ipv6
RP/0/RP0/CPU0:router(config-isis-af)# adjacency-check disable
attached-bit receive ignore
To ignore the attached bit in a received Level 1 link-state packet (LSP), use the attached-bit receive ignore command in address family configuration mode. To remove the attached-bit receive ignore command from the configuration file and restore the system to its default condition, use the no form of this command.
attached-bit receive ignore
no attached-bit receive ignore
Syntax Description
This command has no arguments or keywords.
Defaults
The attached bit is set in the LSP.
Command Modes
Address family configuration
Command History
|
|
Release 3.8.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following example shows how to configure to ignore the attached bit in a received LSP:
RP/0/RP0/CPU0:router(config)# router isis isp1
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# attached-bit receive ignore
Related Commands
|
|
attached-bit send |
Configures an Intermediate System-to-Intermediate System (IS-IS) instance with an attached bit in the Level 1 link-state packet (LSP). |
attached-bit send
To configure an Intermediate System-to-Intermediate System (IS-IS) instance with an attached bit in the Level 1 link-state packet (LSP), use the attached-bit send command in address family configuration mode. To remove the attached-bit send command from the configuration file and restore the system to its default condition, use the no form of this command.
attached-bit send {always-set | never-set}
no attached-bit send {always-set | never-set}
Syntax Description
always-set |
Specifies to always set the attached bit in the LSP. |
never-set |
Specifies to never set the attached bit the LSP. |
Defaults
The attached bit is not set in the LSP.
Command Modes
Address family configuration
Command History
|
|
Release 3.8.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. This command replaces the set-attached-bit command. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the attached-bit send command to set an IS-IS instance with an attached bit in the Level 1 LSP that allows another IS-IS instance to redistribute Level 2 topology. The attached bit is used when the Level 2 connectivity from another IS-IS instance is advertised by the Level 1 attached bit.
Cisco IOS XR software does not support multiple Level 1 areas in a single IS-IS routing instance; however the equivalent functionality is achieved by redistribution of routes between two IS-IS instances by using the redistribute (IS-IS) command.
The attached bit is configured for a specific address family only if the single-topology command is not configured.
Note If connectivity for the Level 2 instance is lost, the attached bit in the Level 1 instance LSP continues sending traffic to the Level 2 instance and causes the traffic to be dropped.
Examples
The following example shows how to configure an Intermediate System-to-Intermediate System (IS-IS) instance with an attached bit:
RP/0/RP0/CPU0:router(config)# router isis isp1
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# attached-bit send always-set
Related Commands
|
|
redistribute (IS-IS) |
Redistribute routes from one routing protocol into Intermediate System-to-Intermediate System (IS-IS). |
single-topology |
Configures the link topology for IPv4 when IPv6 is configured. |
circuit-type
To configure the type of adjacency used for the Intermediate System-to-Intermediate System (IS-IS) protocol, use the circuit-type command in interface configuration mode. To reset the circuit type to Level l and Level 2, use the no form of this command.
circuit-type {level-1 | level-1-2 | level-2-only}
no circuit-type
Syntax Description
level-1 |
Establishes only Level 1 adjacencies over an interface. |
level-1-2 |
Establishes both Level 1 and Level 2 adjacencies, if possible. |
level-2-only |
Establishes only Level 2 adjacencies over an interface. |
Defaults
Default adjacency types are both Level 1 and Level 2 adjacencies.
Command Modes
Interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Adjacencies may not be established even if allowed by the circuit-type command. The proper way to establish adjacencies is to configure a router as a Level 1, Level 1 and Level 2, or Level 2-only system using the is-type command. Only on networking devices that are between areas (Level 1 and Level 2 networking devices) should you configure some interfaces to be Level 2-only to prevent wasting bandwidth by sending out unused Level 1 hello packets. Remember that on point-to-point interfaces, the Level 1 and Level 2 hello packets are in the same packet.
Examples
The following example shows how to configure a Level 1 adjacency with its neighbor on Packet-over-SONET/SDH (POS) interface 0/2/0/0 and Level 2 adjacencies with all Level 2-capable routers on POS interface 0/5/0/2:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# is-type level-1-2
RP/0/RP0/CPU0:router(config-isis)# interface POS0/2/0/0
RP/0/RP0/CPU0:router(config-isis-if)# circuit-type level-1
RP/0/RP0/CPU0:router(config-isis-if)# exit
RP/0/RP0/CPU0:router(config-isis)# interface POS0/5/0/2
RP/0/RP0/CPU0:router(config-isis-if)# circuit-type level-2-only
In this example, only Level 2 adjacencies are established because the is-type command is configured:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# is-type level-2-only
RP/0/RP0/CPU0:router(config-isis)# interface POS0/2/0/0
RP/0/RP0/CPU0:router(config-isis-if)# circuit-type level-1-2
Related Commands
|
|
is-type |
Configures the routing level for an instance of the IS-IS routing process. |
net |
Configures an IS-IS NET for the routing process. |
clear isis process
To clear the link-state packet (LSP) database and adjacency database sessions for an Intermediate System-to-Intermediate System (IS-IS) instance or all IS-IS instances, use the clear isis process command in EXEC mode.
clear isis [instance instance-id] process
Syntax Description
instance instance-id |
(Optional) Specifies IS-IS sessions for the specified IS-IS instance only. •The instance-id argument is the instance identifier (alphanumeric) defined by the router isis command. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the clear isis process command without any keyword to clear all the IS-IS instances. Add the instance instance-id keyword and argument to clear the specified IS-IS instance.
Examples
The following example shows the IS-IS LSP database and adjacency sessions being cleared for instance 1:
RP/0/RP0/CPU0:router# clear isis instance 1 process
Related Commands
clear isis route
To clear the Intermediate System-to-Intermediate System (IS-IS) routes in a topology, use the clear isis route command in EXEC mode.
clear isis [instance instance-id] {afi-all | ipv4 | ipv6} {unicast | multicast | safi-all} [topology topo-name] route
Syntax Description
instance instance-id |
(Optional) Specifies IS-IS sessions for the specified IS-IS instance only. •The instance-id argument is the instance identifier (alphanumeric) defined by the router isis command. |
afi-all |
Specifies IP Version 4 (IPv4) and IP Version 6 (IPv6) address prefixes. |
ipv4 |
Specifies IPv4 address prefixes. |
ipv6 |
Specifies IPv6 address prefixes. |
unicast |
Specifies unicast address prefixes. |
multicast |
Specifies multicast address prefixes. |
safi-all |
Specifies all secondary address prefixes. |
topology topo-name |
(Optional) Specifies topology table information and name of the topology table. |
Defaults
No default behavior or value
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The all keyword was changed to afi-all. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
The following keywords were added: •multicast •safi-all |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
The topology topo-name keyword and argument were added. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the clear isis route command to clear the routes from the specified topology or all routes in all topologies if no topology is specified.
|
|
isis |
execute |
rib |
read, write |
basic-services |
read, write |
Examples
The following example shows how to clear the routes with IPv4 unicast address prefixes:
RP/0/RP0/CPU0:router# clear isis ipv4 unicast route
Related Commands
clear isis statistics
To clear the Intermediate System-to-Intermediate System (IS-IS) statistics, use the clear isis statistics command in EXEC mode.
clear isis [instance instance-id] statistics [interface-type interface-instance]
Syntax Description
instance instance-id |
(Optional) Clears IS-IS sessions for the specified IS-IS instance only. •The instance-id argument is the instance identifier (alphanumeric) defined by the router isis command. |
interface-type |
(Optional) Interface type. For more information, use the question mark (?) online help function. |
interface-instance |
(Optional) Either a physical interface instance or a virtual interface instance as follows: •Physical interface instance. Naming notation is rack/slot/module/port and a slash between values is required as part of the notation. –rack: Chassis number of the rack. –slot: Physical slot number of the modular services card or line card. –module: Module number. A physical layer interface module (PLIM) is always 0. –port: Physical port number of the interface. Note In references to a Management Ethernet interface located on a route processor card, the physical slot number is alphanumeric (RP0 or RP1) and the module is CPU0. Example: interface MgmtEth0/RP1/CPU0/0. •Virtual interface instance. Number range varies depending on interface type. For more information about the syntax for the router, use the question mark (?) online help function. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 3.2 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the clear isis statistics command to clear the information displayed by the show isis statistics command.
|
|
isis |
execute |
rib |
read, write |
basic-services |
read, write |
Examples
The following example shows the IS-IS statistics for a specified interface being cleared:
RP/0/RP0/CPU0:router# clear isis instance 23 statistics
Related Commands
csnp-interval
To configure the interval at which periodic complete sequence number PDUs (CSNPs) packets are sent on broadcast interfaces, use the csnp-interval command in interface configuration mode. To restore the default value, use the no form of this command.
csnp-interval seconds [level {1 | 2}]
no csnp-interval [seconds] [level {1 |2}
Syntax Description
seconds |
Interval (in seconds) of time between transmission of CSNPs on multiaccess networks. This interval applies only for the designated router. Range is 0 to 65535 seconds. |
level {1 | 2} |
(Optional) Specifies the interval of time between transmission of CSNPs for Level 1 or Level 2 independently. |
Defaults
seconds: 10 seconds
Both Level 1 and Level 2 are configured if no level is specified.
Command Modes
Interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The csnp-interval command applies only to the designated router (DR) for a specified interface. Only DRs send CSNP packets to maintain database synchronization. The CSNP interval can be configured independently for Level 1 and Level 2.
Use of the csnp-interval command on point-to-point subinterfaces makes sense only in combination with the IS-IS mesh-group feature.
|
|
isis |
execute |
rib |
read, write |
basic-services |
read, write |
Examples
The following example shows how to set the CSNP interval for Level 1 to 30 seconds:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface POS0/0/2/0
RP/0/RP0/CPU0:router(config-isis-if)# csnp-interval 30 level 1
default-information originate (IS-IS)
To generate a default route into an Intermediate System-to-Intermediate System (IS-IS) routing domain, use the default-information originate command in address family configuration mode. To remove the default-information originate command from the configuration file and restore the system to its default condition, use the no form of this command.
default-information originate [route-policy route-policy-name]
no default-information originate [route-policy route-policy-name]
Syntax Description
route-policy |
(Optional) Defines the conditions for the default route. |
route-policy-name |
(Optional) Name for the route policy map. |
Defaults
A default route is not generated into an IS-IS routing domain.
Command Modes
Address family configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
The route-map map-name keyword and argument were changed to route-policy route-policy-name. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
If a router configured with the default-information originate command has a route to 0.0.0.0 in the routing table, IS-IS originates an advertisement for 0.0.0.0 in its link-state packets (LSPs).
Without a route policy, the default is advertised only in Level 2 LSPs. For Level 1 routing, there is another process to find the default route, which is to look for the closest Level 1 and Level 2 router. The closest Level 1 and Level 2 router can be found by looking at the attached-bit (ATT) in Level 1 LSPs.
A route policy can be used for two purposes:
•To make the router generate the default route in its Level 1 LSPs.
•To advertise 0.0.0.0/0 conditionally.
Examples
The following example shows how to generate a default external route into an IS-IS domain:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# default-information originate
Related Commands
disable (IS-IS)
To disable the Intermediate System-to-Intermediate System (IS-IS) topology on a specified interface, use the disable command in interface address family configuration mode. To remove this function, use the no form of this command.
disable
no disable
Syntax Description
This command has no arguments or keywords.
Defaults
IS-IS protocol is enabled.
Command Modes
Interface address family configuration
Command History
|
|
Release 3.2 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following example shows how to disable the IS-IS protocol for IPv4 unicast on Packet-over-SONET/SDH (POS) interface 0/1/0/1:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface POS0/1/0/1
RP/0/RP0/CPU0:router(config-isis-if)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-if-af)# disable
distance (IS-IS)
To define the administrative distance assigned to routes discovered by the Intermediate System-to-Intermediate System (IS-IS) protocol, use the distance command in address family configuration mode. To remove the distance command from the configuration file and restore the system to its default condition in which the software removes a distance definition, use the no form of this command.
distance weight [prefix mask | prefix/length [prefix-list-name]]
no distance [weight] [prefix mask | prefix/length [prefix-list-name]]
Syntax Description
weight |
Administrative distance to be assigned to IS-IS routes. Range is 1 to 255. |
prefix |
(Optional) The prefix argument specifies the IP address in four-part, dotted-decimal notation. |
mask |
(Optional) IP address mask. |
/length |
(Optional) The length of the IP prefix. A decimal value that indicates how many of the high-order contiguous bits of the address compose the prefix (the network portion of the address). A slash must precede the decimal value. Range is 0 to 32 for IPv4 addresses and 0 to 128 for IPv6 addresses. |
prefix-list-name |
(Optional) List of routes to which administrative distance applies. |
Defaults
weight: 115
Command Modes
Address family configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
An administrative distance is an integer from 1 to 255. In general, the higher the value, the lower the trust rating. An administrative distance of 255 means that the routing information source cannot be trusted at all and should be ignored. Weight values are subjective; no quantitative method exists for choosing weight values.
Use the distance command to configure the administrative distances applied to IS-IS routes when they are inserted into the Routing Information Base (RIB), and influence the likelihood of these routes being preferred over routes to the same destination addresses discovered by other protocols.
The address/prefix-length argument defines to which source router the distance applies. In other words, each IS-IS route is advertised by another router, and that router advertises an address that identifies it. This source address is displayed in the output of the show isis route detail command.
The distance command applies to the routes advertised by routers whose address matches the specified prefix. The prefix-list-name argument can then be used to refine this further so that the distance command affects only specific routes.
Examples
The following example gives a distance of 10 to all routes to 2.0.0.0/8 and 3.0.0.0/8 (or more specific prefixes) that are advertised by routers whose ID is contained in 1.0.0.0/8. It gives a distance of 80 to all other routes.
RP/0/RP0/CPU0:router(config)# ipv4 prefix-list target_routes
RP/0/RP0/CPU0:router(config-ipv4_pfx)# permit 2.0.0.0/8
RP/0/RP0/CPU0:router(config-ipv4_pfx)# permit 3.0.0.0/8
RP/0/RP0/CPU0:router(config-ipv4_pfx)# deny 0.0.0.0/0
RP/0/RP0/CPU0:router(config-ipv4_pfx)# exit
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# distance 10 1.0.0.0/8 target_routes
RP/0/RP0/CPU0:router(config-isis-af)# distance 80
Related Commands
|
|
router isis |
Configures the IS-IS routing protocol and specifies an IS-IS instance. |
show isis protocol |
Displays summary information about the IS-IS instance. |
show isis route detail |
Displays link-state packet (LSP) details. |
hello-interval (IS-IS)
To specify the length of time between hello packets sent by the Intermediate System-to-Intermediate System (IS-IS) protocol software, use the hello-interval command in interface configuration mode. To restore the default value, use the no form of this command.
hello-interval seconds [level {1 | 2}]
no hello-interval [seconds] [level {1 | 2}]
Syntax Description
seconds |
Integer value (in seconds) for the length of time between hello packets. By default, a value three times the hello interval seconds is advertised as the hold time in the hello packets sent. (That multiplier of three can be changed by using the hello-multiplier command.) With smaller hello intervals, topological changes are detected more quickly, but there is more routing traffic. Range is 1 to 65535 seconds. |
level {1 | 2} |
(Optional) Specifies the hello interval for Level 1 and Level 2 independently. For broadcast interfaces only. |
Defaults
seconds: 10 seconds
Both Level 1 and Level 2 are configured if no level is specified.
Command Modes
Interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The hello interval can be configured independently for Level 1 and Level 2, except on serial point-to-point interfaces. (Because only a single type of hello packet is sent on serial links, it is independent of Level 1 or Level 2.) Configuring Level 1 and Level 2 independently is used on LAN interfaces.
Note A shorter hello interval gives quicker convergence, but increases bandwidth and CPU usage. It might also add to instability in the network.
A slower hello interval saves bandwidth and CPU. Especially when used in combination with a higher hello multiplier, this strategy may increase overall network stability.
For point-to-point links, IS-IS sends only a single hello for Level 1 and Level 2, making the level keyword meaningless on point-to-point links. To modify hello parameters for a point-to-point interface, omit the level keyword.
Examples
The following example shows how to configure TenGigE interface 0/6/0/0 to advertise hello packets every 5 seconds for Level 1 topology routes. This situation causes more traffic than configuring a longer interval, but topological changes are detected more quickly.
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface TenGigE 0/6/0/0
RP/0/RP0/CPU0:router(config-isis-if)# hello-interval 5 level 1
Related Commands
|
|
hello-multiplier |
Specifies the number of IS-IS hello packets a neighbor must miss before the router should declare the adjacency as down. |
hello-multiplier
To specify the number of Intermediate System-to-Intermediate System (IS-IS) hello packets a neighbor must miss before the router should declare the adjacency as down, use the hello-multiplier command in interface configuration mode. To restore the default value, use the no form of this command.
hello-multiplier multiplier [level {1 | 2}]
no hello-multiplier [multiplier] [level {1 | 2}]
Syntax Description
multiplier |
Advertised hold time in IS-IS hello packets is set to the hello multiplier times the hello interval. Range is 3 to 1000. Neighbors declare an adjacency to this down router after not having received any IS-IS hello packets during the advertised hold time. The hold time (and thus the hello multiplier and the hello interval) can be set on an individual interface basis, and can be different between different networking devices in one area. Using a smaller hello multiplier gives faster convergence, but can result in more routing instability. Increase the hello multiplier to a larger value to help network stability when needed. Never configure a hello multiplier to a value lower than the default value of 3. |
level {1 | 2} |
(Optional) Specifies the hello multiplier independently for Level 1 or Level 2 adjacencies. |
Defaults
multiplier: 3
Both Level 1 and Level 2 are configured if no level is specified.
Command Modes
Interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The "holding time" carried in an IS-IS hello packet determines how long a neighbor waits for another hello packet before declaring the neighbor to be down. This time determines how quickly a failed link or neighbor is detected so that routes can be recalculated.
Use the hello-multiplier command in circumstances where hello packets are lost frequently and IS-IS adjacencies are failing unnecessarily. You can raise the hello multiplier and lower the hello interval (hello-interval (IS-IS) command) correspondingly to make the hello protocol more reliable without increasing the time required to detect a link failure.
On point-to-point links, there is only one hello for both Level 1 and Level 2. Separate Level 1 and Level 2 hello packets are also sent over nonbroadcast multiaccess (NBMA) networks in multipoint mode, such as X.25, Frame Relay, and ATM.
Examples
The following example shows how the network administrator wants to increase network stability by making sure an adjacency goes down only when many (ten) hello packets are missed. The total time to detect link failure is 60 seconds. This strategy ensures that the network remains stable, even when the link is fully congested.
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface POS0/2/0/1
RP/0/RP0/CPU0:router(config-isis-if)# hello-interval 6
RP/0/RP0/CPU0:router(config-isis-if)# hello-multiplier 10
Related Commands
hello-padding
To configure padding on Intermediate System-to-Intermediate System (IS-IS) hello protocol data units (IIH PDUs) for all IS-IS interfaces on the router, use the hello-padding command in interface configuration mode. To suppress padding, use the no form of this command.
hello-padding {disable | sometimes} [level {1 | 2}]
no hello-padding [disable | sometimes] [level {1 | 2}
Syntax Description
disable |
Suppresses hello padding. |
sometimes |
Enables hello padding during adjacency formation only. |
level {1 | 2} |
(Optional) Specifies hello padding for Level 1 or Level 2 independently. |
Defaults
Hello padding is enabled.
Command Modes
Interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
You might want to suppress hello padding to conserve network resources. The lower the circuit speed, the higher the percentage of padding overhead. Before suppressing the hello padding, you should know your physical and data link layer configurations and have control over them, and also know your router configuration at the network layer.
For point-to-point links, IS-IS sends only a single hello for Level 1 and Level 2, making the level keyword meaningless on point-to-point links. To modify hello parameters for a point-to-point interface, omit the level keyword.
Examples
The following example shows how to suppress IS-IS hello padding over local area network (LAN) circuits for interface POS 0/2/0/1:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface POS0/2/0/1
RP/0/RP0/CPU0:router(config-isis-if)# hello-padding disable
Related Commands
hello-password
To configure the authentication password for an Intermediate System-to-Intermediate System (IS-IS) interface, use the hello-password command in interface configuration mode. To disable authentication, use the no form of this command.
hello-password [hmac-md5 | text] [clear | encrypted] password [level {1 | 2}] [send-only]
no hello-password [hmac-md5 | text] [clear | encrypted] password [level {1 | 2}] [send-only]
Syntax Description
hmac-md5 |
(Optional) Specifies that the password use HMAC-MD5 authentication. |
text |
(Optional) Specifies that the password use clear text password authentication. |
clear |
(Optional) Specifies that the password be unencrypted. |
encrypted |
(Optional) Specifies that the password be encrypted using a two-way algorithm. |
password |
Authentication password you assign for an interface. |
level {1 | 2} |
(Optional) Specifies whether the password is for a Level 1 or a Level 2 protocol data unit (PDU). |
send-only |
(Optional) Specifies that the password applies only to protocol data units (PDUs) that are being sent and does not apply to PDUs that are being received. |
Defaults
Both Level 1 and Level 2 are configured if no level is specified.
password: encrypted text
Command Modes
Interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The clear and encrypted keywords replaced the 0 and 7 keywords, and the hmac-md5, text, and send-only keywords were added. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
The keychain keychain-name keyword and argument were added. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
Removed the keychain keyword and added the hello-password keychain command as a separate command from the hello-password command. Updated the syntax of the hello-password command. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
When a text password is configured, it is exchanged as clear text. Therefore, the hello-password command provides limited security.
When an hmac-md5 password is configured, the password is never sent over the network and is instead used to calculate a cryptographic checksum to ensure the integrity of the exchanged data.
For point-to-point links, IS-IS sends only a single hello for Level 1 and Level 2, making the level keyword meaningless on point-to-point links. To modify hello parameters for a point-to-point interface, omit the level keyword.
Examples
The following example shows how to configure a password with HMAC-MD5 authentication for hello packets running on Packet-over-SONET/SDH (POS) 0/2/0/3 interface:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface POS0/2/0/3
RP/0/RP0/CPU0:router(config-isis-if)# hello-password hmac-md5 clear mypassword
Related Commands
|
|
hello-password keychain |
Configures the authentication password keychain for an Intermediate System-to-Intermediate System (IS-IS) interface. |
hello-password accept |
Configures an additional authentication password for an IS-IS interface. |
hello-password keychain
To configure the authentication password keychain for an Intermediate System-to-Intermediate System (IS-IS) interface, use the hello-password keychain command in interface configuration mode. To disable the authentication password keychain, use the no form of this command.
hello-password keychain keychain-name [level {1 | 2}] [send-only]
no hello-password keychain keychain-name [level {1 | 2}] [send-only]
Syntax Description
keychain |
Keyword that specifies the keychain to be configured. An authentication password keychain is a sequence of keys collectively managed and used for authenticating a peer-to-peer group. |
keychain-name |
Specifies the name of the keychain. |
level {1 | 2} |
(Optional) Specifies whether the keychain is for a Level 1 or a Level 2 protocol data unit (PDU). |
send-only |
(Optional) Specifies that the keychain applies only to protocol data units (PDUs) that are being sent and does not apply to PDUs that are being received. |
Defaults
Both Level 1 and Level 2 are configured if no level is specified.
password: encrypted text
Command Modes
Interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The clear and encrypted keywords replaced the 0 and 7 keywords, and the hmac-md5, text, and send-only keywords were added. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
The keychain keychain-name keyword and argument were added. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
Separated the hello-password keychain command as a separate command from the hello-password command, and updated the syntax of the hello-password command. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Specify a keychain to enable keychain authentication between two IS-IS peers. Use the keychain keychain-name keyword and argument to implement hitless key rollover for authentication.
Examples
The following example shows how to configure a password keychain for level 1, send only authentication on a POS interface:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface POS 0/1/0/0
RP/0/RP0/CPU0:router(config-isis-if)# hello-password keychain mykeychain level 1 send-only
Related Commands
|
|
hello-password |
Configures the authentication password for an Intermediate System-to-Intermediate System (IS-IS) interface. |
hello-password accept |
Configures an additional authentication password for an IS-IS interface. |
hello-password accept
To configure an additional authentication password for an Intermediate System-to-Intermediate System (IS-IS) interface, use the hello-password accept command in interface configuration mode. To disable authentication, use the no form of this command.
hello-password accept {clear | encrypted} password [level {1 | 2}]
no hello-password accept {clear | encrypted} password [level {1 | 2}]
Syntax Description
clear |
Specifies that the password be unencrypted. |
encrypted |
Specifies that the password be encrypted using a two-way algorithm. |
password |
Authentication password you assign. |
level {1 | 2} |
(Optional) Specifies the password for Level 1 or Level 2 independently. |
Defaults
Both Level 1 and Level 2 are configured if no level is specified.
Command Modes
Interface configuration
Command History
|
|
Release 3.2 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the hello-password accept command to add an additional password for an IS-IS interface. An authentication password must be configured using the hello-password command before an accept password can be configured for the corresponding level.
Examples
The following example shows how to configure a password:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface POS0/2/0/3
RP/0/RP0/CPU0:router(config-isis)# hello-password accept encrypted 111D1C1603
Related Commands
|
|
hello-password |
Configures an authentication password for an IS-IS interface. |
hostname dynamic disable
To disable Intermediate System-to-Intermediate System (IS-IS) routing protocol dynamic hostname mapping, use the hostname dynamic command in router configuration mode. To remove the specified command from the configuration file and restore the system to its default condition, use the no form of this command.
hostname dynamic disable
no hostname dynamic disable
Syntax Description
disable |
Disables dynamic host naming. |
Defaults
Router names are dynamically mapped to system IDs.
Command Modes
Router configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
In an IS-IS routing domain, each router is represented by a 6-byte hexadecimal system ID. When network administrators maintain and troubleshoot networking devices, they must know the router name and corresponding system ID.
Link-state packets (LSPs) include the dynamic hostname in the type, length, and value (TLV) which carries the mapping information across the entire domain. Every router in the network, upon receiving the TLV from an LSP, tries to install it in a mapping table. The router then uses the mapping table when it wants to convert a system ID to a router name.
To display the entries in the mapping tables, use the show isis hostname command.
Examples
The following example shows how to disable dynamic mapping of hostnames to system IDs:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# hostname dynamic disable
Related Commands
|
|
hostname |
Specifies the name of the local router. |
show isis hostname |
Displays the router name-to-system ID mapping table. |
ignore-lsp-errors
To override the default setting of a router to ignore Intermediate System-to-Intermediate System (IS-IS) link-state packets (LSPs) that are received with internal checksum errors, use the ignore-lsp-errors disable command in router configuration mode. To enable ignoring IS-IS LSP errors, use the no form of this command.
ignore-lsp-errors disable
no ignore-lsp-errors disable
Syntax Description
disable |
Disables the functionality of the command. |
Defaults
The system ignores corrupt LSPs.
Command Modes
Router configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The IS-IS protocol definition requires that a received LSP with an incorrect data-link checksum be purged by the receiver, which causes the initiator of the packet to regenerate it. However, if a network has a link that causes data corruption while still delivering LSPs with correct data-link checksums, a continuous cycle of purging and regenerating large numbers of packets can occur. Because this situation could render the network nonfunctional, use this command to ignore these LSPs rather than purge the packets.
The receiving network devices use link-state packets to maintain their routing tables.
Examples
The following example shows how to instruct the router to ignore LSPs that have internal checksum errors:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# ignore-lsp-errors disable
interface (IS-IS)
To configure the Intermediate System-to-Intermediate System (IS-IS) protocol on an interface, use the interface command in router configuration mode. To disable IS-IS routing for interfaces, use the no form of this command.
interface type interface-path-id
no interface type interface-path-id
Syntax Description
type |
Interface type. For more information, use the question mark (?) online help function. |
interface-path-id |
Physical interface or virtual interface. Note Use the show interfaces command to see a list of all interfaces currently configured on the router. For more information about the syntax for the router, use the question mark (?) online help function. |
Defaults
No interfaces are specified.
Command Modes
Router configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
An address family must be established on the IS-IS interface before the interface is enabled for IS-IS protocol operation.
Examples
The following example shows how to enable an IS-IS multitopology configuration for IPv6 on Packet-over-SONET/SDH (POS) interface 0/3/0/0:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# net 49.0000.0000.0001.00
RP/0/RP0/CPU0:router(config-isis)# interface POS0/3/0/0
RP/0/RP0/CPU0:router(config-isis-if)# address-family ipv6 unicast
RP/0/RP0/CPU0:router(config-isis-if-af)# metric-style wide level 1
RP/0/RP0/CPU0:router(config)# interface POS0/3/0/0
RP/0/RP0/CPU0:router(config-if)# ipv6 address 2001::1/64
Related Commands
|
|
log adjacency changes (IS-IS) |
Configures the routing level for an instance of the IS-IS routing process. |
net |
Configures an IS-IS network entity title (NET) for the routing process. |
router isis |
Enables the IS-IS routing protocol. |
ipfrr lfa
To enable the IP fast reroute (IPFRR) loop-free alternate (LFA) computation, use the ipfrr lfa command in interface address family configuration mode. To disable this feature, use the no form of this command.
ipfrr lfa {level {1 | 2}}
no ipfrr lfa {level {1 | 2}}
Syntax Description
level {1 | 2} |
Configures IPFRR LFA the for Level 1 or Level 2 independently. |
Defaults
IPFRR LFA is disabled.
Command Modes
Interface address family configuration
Command History
|
|
Release 3.5.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the ipfrr lfa command to compute loop-free alternates for all links or neighbors in the event of a link failure.
To enable node protection on broadcast links, IPRR and bidirectional forwarding detection (BFD) must be enabled on the interface under IS-IS. See Cisco IOS XR Interface and Hardware Configuration Guide for information on configuring BFD.
Note Multiprotocol Label Switching (MPLS) FRR and IPFRR cannot be configured on the same interface simultaneously.
Examples
The following example shows how to configure IPFRR for the IPv4 unicast topology at Level 1:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface POS0/3/0/0
RP/0/RP0/CPU0:router(config-isis-if)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-if-af)# ipfrr lfa level 1
ipfrr lfa exclude interface
To exclude an interface from the IP fast reroute (IPFRR) loop-free alternate (LFA) computation, use the ipfrr lfa exclude interface command in interface address family configuration mode. To disable this feature, use the no form of this command.
ipfrr lfa exclude interface type interface-path-id
no ipfrr lfa exclude interface type interface-path-id
Syntax Description
type |
Interface type. For more information, use the question mark (?) online help function. |
interface-path-id |
Physical interface or virtual interface. Note Use the show interfaces command to see a list of all interfaces currently configured on the router. For more information about the syntax for the router, use the question mark (?) online help function. |
Defaults
IPFRR LFA is disabled.
Command Modes
Interface address family configuration
Command History
|
|
Release 3.8.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the ipfrr lfa command to compute loop-free alternates for all links or neighbors in the event of a link failure.
To enable node protection on broadcast links, IPRR and bidirectional forwarding detection (BFD) must be enabled on the interface under IS-IS. See Cisco IOS XR Interface and Hardware Configuration Guide for information on configuring BFD.
Note Multiprotocol Label Switching (MPLS) FRR and IPFRR cannot be configured on the same interface simultaneously.
Examples
The following example shows how to configure to exclude POS 0/1/0/0 interface from IPFRR LFA:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface POS0/1/0/0
RP/0/RP0/CPU0:router(config-isis-if)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-if-af)# ipfrr lfa exclude interface POS0/1/0/0
Related Commands
|
|
ipfrr lfa |
Enable the IP fast reroute (IPFRR) loop-free alternate (LFA) computation |
ispf
To configure the incremental shortest path first (iSPF) algorithm to calculate network topology, use the ispf command in address family configuration mode. To disable this algorithm function, use the no form of this command.
ispf [level {1 | 2}]
no ispf [level {1 | 2}]
Syntax Description
level {1 | 2} |
(Optional) Configures the iSPF algorithm for Level 1 or Level 2 independently. |
Defaults
The iSPF algorithm is not configured.
Command Modes
Address family configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
The startup-delay seconds keyword and argument were removed. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The iSPF algorithm may be used to reduce the processor load when IS-IS needs to recalculate its topology after minor changes.
Examples
The following example shows how to configure iSPF for the IPv4 unicast topology at Level 1:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# ispf level 1
is-type
To configure the routing level for an Intermediate System-to-Intermediate System (IS-IS) area, use the is-type command in router configuration mode. To set the routing level to the default level, use the no form of this command.
is-type {level-1 | level-1-2 | level-2-only}
no is-type [level-1 | level-1-2 | level-2-only]
Syntax Description
level-1 |
Specifies that the router perform only Level 1 (intra-area) routing. This router learns only about destinations inside its area. Level 2 (interarea) routing is performed by the closest Level 1-2 router. |
level-1-2 |
Specifies that the router perform both Level 1 and Level 2 routing. |
level-2-only |
Specifies that the routing process acts as a Level 2 (interarea) router only. This router is part of the backbone, and does not communicate with Level 1-only routers in its own area. |
Defaults
Both Level 1 and Level 2 are configured if no level is specified.
Command Modes
Router configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
When the router is configured with Level 1 routing only, this router learns about destinations only inside its area. Level 2 (interarea) routing is performed by the closest Level 1-2 router.
When the router is configured with Level 2 routing only, this router is part of the backbone, and does not communicate with Level 1 routers in its own area.
The router has one link-state packet database (LSDB) for destinations inside the area (Level 1 routing) and runs a shortest path first (SPF) calculation to discover the area topology. It also has another LSDB with link-state packets (LSPs) of all other backbone (Level 2) routers, and runs another SPF calculation to discover the topology of the backbone and the existence of all other areas.
We highly recommend that you configure the type of an IS-IS routing process to establish the proper level of adjacencies. If there is only one area in the network, there is no need to run both Level 1 and Level 2 routing algorithms.
Examples
The following example shows how to specify that the router is part of the backbone and that it does not communicate with Level 1-only routers:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# is-type level-2-only
Related Commands
log adjacency changes (IS-IS)
To cause an IS-IS instance to generate a log message when an Intermediate System-to-Intermediate System (IS-IS) adjacency changes state (up or down), use the log adjacency changes command in router configuration mode. To restore the default value, use the no form of this command.
log adjacency changes
no log adjacency changes
Syntax Description
This command has no arguments or keywords.
Defaults
No log messages are generated.
Command Modes
Router configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the log adjacency changes command to monitor IS-IS adjacency state changes; it may be very useful when monitoring large networks. Messages are logged using the system error message facility. Messages are of the forms:
%ISIS-4-ADJCHANGE: Adjacency to 0001.0000.0008 (POS0/2/1/0) (L2) Up, new adjacency
%ISIS-4-ADJCHANGE: Adjacency to router-gsr8 (POS0/2/1/0) (L1) Down, Holdtime expired
Using the no form of the command removes the specified command from the configuration file and restores the system to its default condition with respect to the command.
Examples
The following example shows how to configure the router to log adjacency changes:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# log adjacency changes
Related Commands
|
|
logging |
Logs messages to a syslog server host. |
log pdu drops
To log Intermediate System-to-Intermediate System (IS-IS) protocol data units (PDUs) that are dropped, use the log pdu drops command in router configuration mode. To disable this function, use the no form of this command.
log pdu drops
no log pdu drops
Syntax Description
This command has no arguments or keywords.
Defaults
PDU logging is disabled.
Command Modes
Router configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the log pdu drops command to monitor a network when IS-IS PDUs are suspected of being dropped. The reason for the PDU being dropped and current PDU drop statistics are recorded.
The following are examples of PDU messages:
%ISIS-4-ERR_IIH_INPUT_Q_OVERFLOW: IIH input queue overflow: 86 total drops; 19 IIH drops,
44 LSP drops, 23 SNP drops
%ISIS-4-ERR_LSP_INPUT_Q_OVERFLOW: LSP input queue overflow: 17 total drops; 9 IIH drops, 3
LSP drops, 5 SNP drops
Examples
The following example shows how to enable PDU logging:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# log pdu drops
lsp fast-flood threshold
To configure the link-state packet (LSP) threshold, use the lsp fast-flood threshold command in interface configuration mode. To restore the default value, use the no form of this command.
lsp fast-flood threshold lsp-number [level {1 | 2}]
no lsp fast-flood threshold [lsp-number] [level {1 | 2}]
Syntax Description
lsp-number |
Number of LSPs to send back to back. Range is 1 to 4294967295. |
level {1 | 2} |
(Optional) Specifies the LSP threshold for Level 1 or Level 2 independently. |
Defaults
10 LSPs are allowed in a back-to-back window
Command Modes
Interface configuration
Command History
|
|
Release 3.4.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the lsp fast-flood threshold command to accelerate convergence of LSP database. LSPs are sent back-to-back over an interface up to the specified limit. Past the limit, LSPs are sent out in the next batch window as determined by LSP pacing interval.
Duration of back-to-back window = LSP interval * LSP fast-flood threshold limit.
Examples
The following example shows how to configure the LSP threshold:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface POS 0/3/0/0
RP/0/RP0/CPU0:router(config-isis-if)# lsp fast-flood threshold 234 level 1
Related Commands
|
|
lsp-interval |
Configures the amount of time between each LSP sent on an IS-IS interface. |
lsp-gen-interval
To customize IS-IS throttling of link-state packet (LSP) generation, use the lsp-gen-interval command in router configuration mode. To restore the default value, use the no form of this command.
lsp-gen-interval {[initial-wait initial] [secondary-wait secondary] [maximum-wait maximum]} [level {1 | 2}]
no lsp-gen-interval [[initial-wait initial] [secondary-wait secondary] [maximum-wait maximum]] [level {1 | 2}]
Syntax Description
initial-wait initial |
Specifies the initial LSP generation delay (in milliseconds). Range is 0 to 120000 milliseconds. |
secondary-wait secondary |
Specifies the hold time between the first and second LSP generation (in milliseconds). Range is 1 to 120000 milliseconds. |
maximum-wait maximum |
Specifies the maximum interval (in milliseconds) between two consecutive occurrences of an LSP being generated. Range is 1 to 120000 milliseconds. |
level {1 | 2} |
(Optional) Specifies the LSP time interval for Level 1 or Level 2 independently. |
Defaults
initial-wait initial: 50 milliseconds
secondary-wait secondary: 200 milliseconds
maximum-wait maximum: 5000 milliseconds
Command Modes
Router configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
The initial-wait initial, secondary-wait secondary, and maximum-wait maximum keywords and arguments were added. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
During prolonged periods of network instability, repeated recalculation of LSPs can cause increased CPU load on the local router. Further, the flooding of these recalculated LSPs to the other Intermediate Systems in the network causes increased traffic and can result in other routers having to spend more time running route calculations.
Use the lsp-gen-interval command to reduce the rate of LSP generation during periods of instability in the network. This command can help to reduce CPU load on the router and to reduce the number of LSP transmissions to its IS-IS neighbors.
Examples
The following example shows how to set the maximum interval between two consecutive occurrences of an LSP to 15 milliseconds and the initial LSP generation delta to 5 milliseconds:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# lsp-gen-interval maximum-wait 15 initial-wait 5
Related Commands
lsp-interval
To configure the amount of time between each link-state packet (LSP) sent on an Intermediate System-to-Intermediate System (IS-IS) interface, use the lsp-interval command in interface configuration mode. To restore the default value, use the no form of this command.
lsp-interval milliseconds [level {1 | 2}]
no lsp-interval [milliseconds] [level {1 | 2}]
Syntax Description
milliseconds |
Time delay (in milliseconds) between successive LSPs. Range is 1 to 4294967295. |
level {1 | 2} |
(Optional) Configures the LSP time delay for Level 1 or Level 2 independently. |
Defaults
milliseconds: 33 milliseconds
Command Modes
Interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following example shows how to cause the system to send LSPs every 100 milliseconds (10 packets per second) on Level 1 and Level 2:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface POS0/2/0/1
RP/0/RP0/CPU0:router(config-isis-if)# lsp-interval 100
Related Commands
lsp-mtu
To set the maximum transmission unit (MTU) size of Intermediate System-to-Intermediate System (IS-IS) link-state packets (LSPs), use the lsp-mtu command in router configuration mode. To restore the default, use the no form of this command.
lsp-mtu bytes [level {1 | 2}]
no lsp-mtu [bytes] [level {1 | 2}]
Syntax Description
bytes |
Maximum packet size in bytes. The number of bytes must be less than or equal to the smallest MTU of any link in the network. Range is 128 to 4352 bytes. |
level {1 | 2} |
(Optional) Specifies routing Level 1 or Level 2 independently. |
Defaults
Both Level 1 and Level 2 are configured if no level is specified.
Command Modes
Router configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Under normal conditions, the default MTU size should be sufficient. However, if the MTU size of a link is less than 1500 bytes, the LSP MTU size must be lowered accordingly on each router in the network. If this action is not taken, routing becomes unpredictable.
This guideline applies to all Cisco networking devices in a network. If any link in the network has a reduced MTU size, all devices must be changed, not just the devices directly connected to the link.
Note Do not set the lsp-mtu command (network layer) to a value greater than the link MTU size that is set with the mtu command (physical layer).
To be certain about a link MTU size, use the show isis interface command to display the value.
Examples
The following example shows how to set the MTU size to 1300 bytes:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# lsp-mtu 1300
Related Commands
|
|
mtu |
Adjusts the maximum packet size or MTU size. |
show isis interface |
Displays information about the IS-IS interface. |
lsp-password
To configure the link-state packet (LSP) authentication password, use the lsp-password command in router configuration mode. To remove the lsp-password command from the configuration file and disable link-state packet authentication, use the no form of this command.
lsp-password [[hmac-md5 | text] [clear | encrypted] password | keychain keychain-name] [level {1 | 2}] [send-only] [snp send-only]
no lsp-password [[hmac-md5 | text] [clear | encrypted] password | keychain keychain-name] [level {1 | 2}] [send-only] [snp send-only]
Syntax Description
hmac-md5 |
Specifies that the password uses HMAC-MD5 authentication. |
text |
Specifies that the password uses clear text password authentication. |
clear |
Specifies that the password be unencrypted. |
encrypted |
Specifies that the password be encrypted using a two-way algorithm. |
password |
Authentication password you assign. |
keychain |
(Optional) Specifies a keychain. |
keychain-name |
Name of the keychain. |
level {1 | 2} |
(Optional) Specifies the password for Level 1 or Level 2 independently. |
send-only |
(Optional) Adds passwords to LSP and sequence number protocol (SNP) data units when they are sent. Does not check for authentication in received LSPs or sequence number PDUs (SNPs). |
snp send-only |
(Optional) Adds passwords to SNP data units when they are sent. Does not check for authentication in received SNPs. This option is available when the text keyword is specified. |
Defaults
Both Level 1 and Level 2 are configured if no level is specified.
Command Modes
Router configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The hmac-md5, text, clear, and encrypted keywords replaced the 0 and 7 keywords, the snp validate keyword was removed, and the send-only keyword was added |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
The keychain keychain-name keyword and argument were added. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
When a text password is configured, it is exchanged as clear text. Therefore, the lsp-password command provides limited security.
When an HMAC-MD5 password is configured, the password is never sent over the network and is instead used to calculate a cryptographic checksum to ensure the integrity of the exchanged data.
The recommended password configuration is that both incoming and outgoing SNPs be authenticated.
Note To disable SNP password checking, the snp send-only keywords must be specified in the lsp-password command.
To configure an additional password, use the lsp-password accept command.
Specify a key chain to enable key chain authentication between two IS-IS peers. Use the keychain keychain-name keyword and argument to implement hitless key rollover for authentication.
Examples
The following example shows how to configure separate Level 1 and Level 2 LSP and SNP passwords, one with HMAC-MD5 authentication and encryption and one with clear text password authentication and no encryption:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# lsp-password hmac-md5 clear password1 level 1
RP/0/RP0/CPU0:router(config-isis)# lsp-password text clear password2 level 2
Related Commands
|
|
lsp-password accept |
Configures an additional LSP password when one LSP password is already configured for a level. |
lsp-password accept
To configure an additional link-state packet (LSP) authentication password, use the lsp-password accept command in router configuration mode. To remove the lsp-password accept command from the configuration file and restore the system to its default condition, use the no form of this command.
lsp-password accept {clear | encrypted} password [level {1 | 2}]
no lsp-password accept [{clear | encrypted} password [level {1 | 2}]]
Syntax Description
clear |
Specifies that the password be unencrypted. |
encrypted |
Specifies that the password be encrypted using a two-way algorithm. |
password |
Authentication password you assign. |
level {1 | 2} |
(Optional) Specifies the password for Level 1 or Level 2 independently. |
Defaults
Both Level 1 and Level 2 are configured if no level is specified.
Command Modes
Router configuration
Command History
|
|
Release 3.2 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The lsp-password accept command adds an additional password for use when validating incoming LSPs and sequence number PDUs (SNPs). An LSP password must be configured using the lsp-password command before an accept password can be configured for the corresponding level.
Examples
The following example shows how to configure an accept Level 1 LSP and SNP password:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# lsp-password accept encrypted password1 level 1
Related Commands
lsp-refresh-interval
To set the time between regeneration of link-state packets (LSPs) that contain different sequence numbers, use the lsp-refresh-interval command in router configuration mode. To restore the default refresh interval, use the no form of this command.
lsp-refresh-interval seconds [level {1 | 2}]
no lsp-refresh-interval [seconds [level {1 | 2}]]
Syntax Description
seconds |
Refresh interval (in seconds). Range is 1 to 65535 seconds. |
level {1 | 2} |
(Optional) Specifies routing Level 1 or Level 2 independently. |
Defaults
seconds: 900 seconds (15 minutes)
Both Level 1 and Level 2 are configured if no level is specified.
Command Modes
Router configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The refresh interval determines the rate at which the software periodically sends the route topology information that it originates. This behavior is done to keep the information from becoming too old. By default, the refresh interval is 900 seconds (15 minutes).
LSPs must be refreshed periodically before their lifetimes expire. The refresh interval must be less than the LSP lifetime specified with this router command. Reducing the refresh interval reduces the amount of time that undetected link-state database corruption can persist at the cost of increased link utilization. (This event is extremely unlikely, however, because there are other safeguards against corruption.) Increasing the interval reduces the link utilization caused by the flooding of refreshed packets (although this utilization is very small).
Examples
The following example shows how to change the LSP refresh interval to 10,800 seconds (3 hours):
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# lsp-refresh-interval 10800
Related Commands
|
|
max-lsp-lifetime |
Sets the maximum time that LSPs persist without being refreshed. |
maximum-paths (IS-IS)
To configure the maximum number of parallel routes that an IP routing protocol will install into the routing table, use the maximum-paths command in address family configuration mode. To remove the maximum-paths command from the configuration file and restore the system to its default condition with respect to the routing protocol, use the no form of this command.
maximum-paths maximum
no maximum-paths
Syntax Description
maximum |
Maximum number of parallel routes that IS-IS can install in a routing table. Range is 1 to 32 for Cisco CRS-1s and 1 to 16 for Cisco XR 12000 Series Routers. |
Defaults
maximum (Cisco CRS-1): 8 routes
maximum (Cisco XR 12000 Series Router): 8 routes
Command Modes
Address family configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following example shows how to allow a maximum of 16 paths to a destination:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# maximum-paths 16
maximum-redistributed-prefixes (IS-IS)
To specify an upper limit on the number of external prefixes (subject to summarization) that the Intermediate System-to-Intermediate System (IS-IS) protocol advertises, use the maximum-redistributed-prefixes command in address family mode. To disable this feature, use the no form of this command.
maximum-redistributed-prefixes maximum [level {1 | 2}]
no maximum-redistributed-prefixes [maximum [level {1 | 2}]]
Syntax Description
maximum |
Maximum number of redistributed prefixes advertised. Range is 1 to 28000. |
level {1 | 2} |
(Optional) Specifies maximum prefixes for Level 1 or Level 2. |
Defaults
maximum: 10000
level: 1-2
Command Modes
Address family configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the maximum-redistributed-prefixes command to prevent a misconfiguration from resulting in redistribution of the Internet. If IS-IS encounters more than the maximum number of prefixes, it sets a bi-state alarm. If the number of to-be-redistributed prefixes drops back to the maximum or lower—either through reconfiguration or a change in the redistribution source—IS-IS clears the alarm.
Examples
The following example shows how to specify the number of redistributed prefixes at 5000 for Level 2:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# maximum-redistributed-prefixes 5000 level 2
max-lsp-lifetime
To set the maximum time that link-state packets (LSPs) persist without being refreshed, use the max-lsp-lifetime command in router configuration mode. To restore the default time, use the no form of this command.
max-lsp-lifetime seconds [level {1 | 2}]
no max-lsp-lifetime [seconds [level {1 | 2}]]
Syntax Description
seconds |
Lifetime (in seconds) of the LSP. Range from 1 to 65535 seconds. |
level {1 | 2} |
(Optional) Specifies routing Level 1 or Level 2 independently. |
Defaults
seconds: 1200 seconds (20 minutes)
Both Level 1 and Level 2 are configured if no level is specified.
Command Modes
Router configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
You might need to adjust the maximum LSP lifetime if you change the LSP refresh interval with the lsp-refresh-interval command. The maximum LSP lifetime must be greater than the LSP refresh interval.
Examples
The following example shows how to set the maximum time that the LSP persists to 11,000 seconds (more than 3 hours):
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# max-lsp-lifetime 11000
Related Commands
mesh-group (IS-IS)
To optimize link-state packet (LSP) flooding in highly meshed networks, use the mesh-group command in interface configuration mode. To remove a subinterface from a mesh group, use the no form of this command.
mesh-group {number | blocked}
no mesh-group
Syntax Description
number |
Number identifying the mesh group of which this interface is a member. Range is 1 to 4294967295. |
blocked |
Specifies that no LSP flooding takes place on this interface. |
Defaults
There is no mesh group configuration (normal LSP flooding).
Command Modes
Interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The {number | blocked} argument and keyword was changed from optional to mandatory. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
LSPs first received on subinterfaces that are not part of a mesh group are flooded to all other subinterfaces in the usual way.
LSPs first received on subinterfaces that are part of a mesh group are flooded to all interfaces except those in the same mesh group. If the blocked keyword is configured on a subinterface, then a newly received LSP is not flooded out over that interface.
To minimize the possibility of incomplete flooding, you should allow unrestricted flooding over at least a minimal set of links in the mesh. Selecting the smallest set of logical links that covers all physical paths results in very low flooding, but less robustness. Ideally you should select only enough links to ensure that LSP flooding is not detrimental to scaling performance, but enough links to ensure that under most failure scenarios, no router is logically disconnected from the rest of the network. In other words, blocking flooding on all links permits the best scaling performance, but there is no flooding. Permitting flooding on all links results in very poor scaling performance.
Note See RFC 2973 for details about the mesh group specification.
Examples
In the following example, six interfaces are configured in three mesh groups. LSPs received are handled as follows:
•LSPs first received by Packet-over-SONET/SDH (POS) interface 0/1/0/0 are flooded to all interfaces except POS 0/1/0/1 (which is part of the same mesh group) and POS 0/3/0/0 (which is blocked).
•LSPs first received by POS 0/2/0/1 are flooded to all interfaces except POS 0/2/0/0 (which is part of the same mesh group) and POS 0/3/0/0 (which is blocked).
•LSPs first received by POS 0/3/0/0 are not ignored, but flooded as usual to all interfaces.
•LSPs received first through POS 0/3/0/1 are flooded to all interfaces, except POS 0/3/0/0 (which is blocked).
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface POS0/1/0/0
RP/0/RP0/CPU0:router(config-isis-if)# mesh-group 10
RP/0/RP0/CPU0:router(config-isis-if)# exit
RP/0/RP0/CPU0:router(config-isis)# interface POS0/1/0/1
RP/0/RP0/CPU0:router(config-isis-if)# mesh-group 10
RP/0/RP0/CPU0:router(config-isis-if)# exit
RP/0/RP0/CPU0:router(config-isis)# interface POS0/2/0/0
RP/0/RP0/CPU0:router(config-isis-if)# mesh-group 11
RP/0/RP0/CPU0:router(config-isis-if)# exit
RP/0/RP0/CPU0:router(config-isis)# interface POS0/2/0/1
RP/0/RP0/CPU0:router(config-isis-if)# mesh-group 11
RP/0/RP0/CPU0:router(config-isis-if)# exit
RP/0/RP0/CPU0:router(config-isis)# interface POS0/3/0/1
RP/0/RP0/CPU0:router(config-isis-if)# mesh-group 12
RP/0/RP0/CPU0:router(config-isis-if)# exit
RP/0/RP0/CPU0:router(config-isis)# interface POS0/3/0/0
RP/0/RP0/CPU0:router(config-isis-if)# mesh-group blocked
metric (IS-IS)
To configure the metric for Intermediate System-to-Intermediate System (IS-IS) interfaces, use the metric command in address family or interface address family configuration mode. To restore the default metric value, use the no form of this command.
metric {default-metric | maximum} [level {1 | 2}]
no metric [{default-metric | maximum} [level {1 | 2}]]
Syntax Description
default-metric |
Metric assigned to the link and used to calculate the cost from each other router using the links in the network to other destinations. Range is 1 to 63 for narrow metric and 1 to 16777214 for wide metric. Note Setting the default metric under address family results in setting the same metric for all interfaces that is associated with the address family. Setting a metric value under an interface overrides the default metric. |
maximum |
Specifies maximum wide metric. All routers exclude this link from their shortest path first (SPF). |
level {1 | 2} |
(Optional) Specifies the SPF calculation for Level 1 or Level 2 independently. |
Defaults
default-metric: 10
Both Level 1 and Level 2 are configured if no level is specified.
Command Modes
Address family configuration
Interface address family configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
Default metric value was set to 10. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Set the default metric under address family to set the same metric for all interfaces that is associated with the address family. Set a metric value under an interface to override the default metric.
Specifying the level keyword resets the metric only for Level 1 or Level 2 routing, respectively.
We highly recommend that you configure metrics on all interfaces.
Metrics of more than 63 cannot be used with narrow metric style.
Examples
The following example shows how to configure Packet-over-SONET/SDH 0/1/0/1 interface with a default link-state metric cost of 15 for Level 1:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface POS0/1/0/1
RP/0/RP0/CPU0:router(config-isis-if)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-if-af)# metric 15 level 1
The following example shows how to configure a metric cost of 15 for all interfaces under address family IPv4 unicast for level 2:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# metric 15 level 2
Related Commands
|
|
metric-style narrow |
Configures a router running IS-IS so that it generates and accepts old-style TLV objects. |
metric-style transition |
Configures the software to generate and accept both old-style and new-style TLV objects. |
metric-style wide |
Configures the software to generate and accept only new-style TLV objects objects. |
metric-style narrow
To configure the Intermediate System-to-Intermediate System (IS-IS) software to generate and accept old-style type, length, and value (TLV) objects, use the metric-style narrow command in address family configuration mode. To remove the metric-style narrow command from the configuration file and restore the system to its default condition, use the no form of this command.
metric-style narrow [transition] [level {1 | 2}]
no metric-style narrow [transition] [level {1 | 2}]
Syntax Description
transition |
(Optional) Instructs the router to generate and accept both old-style and new-style TLV objects. It generates only old-style TLV objects. |
level {1 | 2} |
(Optional) Specifies routing Level 1 or Level 2 independently. |
Defaults
Old-style TLVs are generated.
Both Level 1 and Level 2 are configured if no level is specified.
Command Modes
Address family configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
IS-IS traffic engineering extensions include new-style TLV objects with wider metric fields than old-style TLV objects. By default, the router generates old-style TLV objects only. To perform Multiprotocol Label Switching traffic engineering (MPLS TE), a router must generate new-style TLV objects.
Examples
The following example shows how to configure the router to generate and accept only old-style TLV objects on router Level 1:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# metric-style narrow level 1
Related Commands
metric-style transition
To configure the Intermediate System-to-Intermediate System (IS-IS) software to generate and accept both old-style and new-style type, length, and value (TLV) objects, use the metric-style transition command in address family configuration mode. To remove the metric-style transition command from the configuration file and restore the system to its default condition, use the no form of this command.
metric-style transition [level {1 | 2}]
no metric-style transition [level {1 | 2}]
Syntax Description
transition |
Instructs the router to generate and accept both old-style and new-style TLV objects. |
level {1 | 2} |
(Optional) Specifies routing Level 1 or Level 2 independently. |
Defaults
Old-style TLVs are generated, if this command is not configured.
Both Level 1 and Level 2 are configured if no level is specified.
Command Modes
Address family configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
IS-IS traffic engineering extensions include new-style TLV objects with wider metric fields than old-style TLV objects. By default, the router generates old-style TLV objects only. To perform Multiprotocol Label Switching traffic engineering (MPLS TE), a router needs to generate new-style TLV objects.
Examples
The following example shows how to configure the router to generate and accept both old-style and new-style TLV objects on Level 2:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# metric-style transition level 2
Related Commands
metric-style wide
To configure the Intermediate System-to-Intermediate System (IS-IS) software to generate and accept only new-style type, length, and value (TLV) objects, use the metric-style wide command in address family configuration mode. To remove the metric-style wide command from the configuration file and restore the system to its default condition, use the no form of this command.
metric-style wide [transition] [level {1 | 2}]
no metric-style wide [transition] [level {1 | 2}]
Syntax Description
transition |
(Optional) Instructs the router to generate and accept both old-style and new-style TLV objects. It generates only new-style TLV objects. |
level {1 | 2} |
(Optional) Specifies routing Level 1 or Level 2 independently. |
Defaults
Old-style TLV lengths are generated, if this command is not configured.
Both Level 1 and Level 2 are configured if no level is specified.
Command Modes
Address family configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
IS-IS traffic engineering extensions include new-style TLV objects with wider metric fields than old-style TLV objects. If you enter the metric-style wide command, a router generates and accepts only new-style TLV objects. Therefore, the router uses less memory and fewer other resources rather than generating both old-style and new-style TLV objects.
To perform MPLS traffic engineering, a router needs to generate new-style TLV objects.
Note This discussion of metric styles and transition strategies is oriented toward traffic engineering deployment. Other commands and models may be appropriate if the new-style TLV objects are desired for other reasons. For example, a network may require wider metrics, but may not use traffic engineering.
Examples
The following example shows how to configure a router to generate and accept only new-style TLV objects on Level 1:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# metric-style wide level 1
Related Commands
mpls ldp auto-config
To enable Label Distribution Protocol (LDP) Interior Gateway Protocol (IGP) interface auto-configuration, use the mpls ldp auto-config command in IPv4 address family configuration mode. To disable LDP IGP auto-configuration, use the no form of this command.
mpls ldp auto-config
no mpls ldp auto-config
Syntax Description
This command has no arguments or keywords.
Defaults
LDP IGP auto-configuration is disabled.
Command Modes
IPv4 address family configuration
Command History
|
|
Release 3.5.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the mpls ldp auto-config command to automatically configure LDP on a set of interfaces associated with a specified IGP instance. Further, LDP IGP auto-configuration provides a means to block LDP from being enabled on a specified interface. If you do not want an IS-IS interface to have LDP enabled, use the igp auto-config disable command.
Examples
The following example shows how to enable LDP IGP auto-configuration:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# mpls ldp auto-config
Related Commands
|
|
igp auto-config disable |
Disables LDP IGP auto-configuration for a specific interface. |
mpls ldp sync (IS-IS)
To configure Label Distribution Protocol (LDP) IS-IS synchronization, use the mpls ldp sync command in interface address family configuration mode. To disable LDP synchronization, use the no form of this command.
mpls ldp sync [level {1 | 2}]
no mpls ldp sync [level {1 | 2}]
Syntax Description
level {1 | 2} |
(Optional) Sets LDP synchronization for the specified level. |
Defaults
If a level is not specified, LDP synchronization is set for both levels.
Command Modes
Interface address family configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
MPLS VPN traffic forwarded using LDP labels may be dropped in the following instances:
•A new link is introduced in the network and IS-IS has converged before LDP establishes labels.
•An existing LDP session goes down while IS-IS adjacency is intact over the link.
In both instances, outbound LDP labels are not available for forwarding MPLS traffic. LDP IS-IS synchronization addresses the traffic drop. When the mpls ldp sync command is configured, IS-IS advertises the maximum possible link metric until LDP has converged over the link. The link is less preferred and least used in forwarding MPLS traffic. When LDP establishes the session and exchanges labels, IS-IS advertises the regular metric over the link.
Note IS-IS advertises the maximum metric -1 (16777214) if wide metrics are configured since the maximum wide metric is specifically used for link exclusion from the shortest path first algorithm (SPF) (RFC 3784). However, the maximum narrow metric is unaffected by this definition.
Examples
The following example shows how to enable LDP IS-IS synchronization:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface POS 0/3/0/0
RP/0/RP0/CPU0:router(config-isis-if)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-if-af)# mpls ldp sync
Related Commands
mpls traffic-eng
To configure a router running the Intermediate System-to-Intermediate System (IS-IS) protocol to flood Multiprotocol Label Switching traffic engineering (MPLS TE) link information into the indicated IS-IS level, use the mpls traffic-eng command in IPv4 address family configuration mode. To disable this feature, use the no form of this command.
mpls traffic-eng {level-1 | level-1-2 | level-2-only}
no mpls traffic-eng [level-1 | level-1-2 | level-2-only]
Syntax Description
level-1 |
Specifies routing level 1. |
level-1-2 |
Specifies routing levels 1 and 2. |
level-2-only |
Specifies routing level 2. |
Defaults
Flooding is disabled.
Command Modes
IPv4 address family configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The level keyword became mandatory. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
The level {1 | 2} keywords were removed. The following keywords were added: •level-1 •level-1-2 •level-2-only |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the mpls traffic-eng command, which is part of the routing protocol tree, to flood link resource information (such as available bandwidth) for appropriately configured links in the link-state packet (LSP) of the router.
Examples
The following example shows how to turn on MPLS traffic engineering for IS-IS level 1:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# mpls traffic-eng level-1
Related Commands
mpls traffic-eng igp-intact (IS-IS)
To ensure that IS-IS protocol installs both TE and non-TE nexthops in the Routing Information Base (RIB), use the mpls traffic-eng igp-intact command in IPv4 address family (unicast) configuration mode. To disable installing both the TE and non-TE nexthops in the RIB, use the no form of this command.
mpls traffic-eng igp-intact
no mpls traffic-eng igp-intact
Syntax Description
This command has no arguments or keywords.
Command Default
IGP-intact is disabled.
Command Modes
IPv4 address family configuration
Command History
|
|
Release 3.7.0 |
This command was introduced on the Cisco CRS-1 and the Cisco XR 12000 Series Router. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
When multiple TE tunnels and multiple IPv4 (ECMP) nexthops are available to reach an ISIS-learnt prefix, ISIS will pack nexthops in such a way that TE tunnels are preferred up to {maximum-paths - 1} with one IPv4 nexthop. When the number of TE tunnels is less than {maximum-paths - 1}, the remaining nexthops up to maximum-paths will be filled with any available (ECMP) IPv4 nexthops.
The IS-IS protocol adds both tunnel next-hops (igp-shortcuts) and IPv4 next-hops to the next-hop list in the Routing Information Base (RIB), until it reaches the maximum number of paths. When IGP-intact is enabled, it ensures that the Routing Information Base (RIB) always has at least one IPv4 next-hop present in the list of next-hops when the number of paths is at maximum.
The IGP-intact is recommended to be used when Policy-Based Tunnel Selection (PBTS) is in use. This ensures that at least one IPv4 next-hop is available for the default Differentiated Services Code Point (DSCP) traffic class. It also prevents traffic loss for other DSCP traffic classes by diverting such traffic to an IPv4 next-hop when the corresponding tunnel is unavailable for forwarding.
Note that when Policy-Based Tunnel Selection (PBTS) is in use, traffic that is not policy-based is forwarded to an IGP path. In TE-FRR environments where IP-FRR (IP-fast reroute) is not in use, such traffic may not have fast reroute (FRR) protection.
Examples
The following example shows how to enable IGP-intact:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# mpls traffic-eng igp-intact
RP/0/RP0/CPU0:router(config-isis-af)# commit
Related Commands
|
|
mpls traffic-eng igp-intact (OSPF) |
Ensures that the OSPF protocol installs at least one IPv4 next-hop when it adds the tunnel next-hops (igp-shortcuts). |
mpls traffic-eng multicast-intact (IS-IS)
To enable a router that is running the Intermediate System-to-Intermediate System (IS-IS) protocol so that Protocol-Independent Multicast (PIM) and Multiprotocol Label Switching (MPLS) traffic engineering operate, use the mpls traffic-eng multicast-intact command in IPv4 address family configuration mode. To disable this feature, use the no form of this command.
mpls traffic-eng multicast-intact
no mpls traffic-eng [multicast-intact]
Syntax Description
This command has no arguments or keywords.
Defaults
Multicast-intact is disabled.
Command Modes
IPv4 address family configuration
Command History
|
|
Release 3.2 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
If Multiprotocol Label Switching Traffic Engineering (MPLS-TE) is configured through the IS-IS routing domain and multicast protocols (like Protocol Independent Multicast [PIM]) are also enabled, then use the mpls traffic-end multicast-intact command to install nontraffic engineering next hops in the Routing Information Base (RIB) for use by multicast. The installation of IP-only next hops is in addition to the installation of the standard set of paths for a prefix, which might be over traffic engineered tunnels.
The mpls traffic-eng multicast-intact command allows PIM to use the native hop-by-hop neighbors even though the unicast routing is using MPLS TE tunnels.
Examples
The following example shows how to enable the multicast-intact feature:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# mpls traffic-eng multicast-intact
Related Commands
|
|
show isis route |
Displays IP reachability information for an IS-IS instance, optionally for multicast-intact. |
show isis topology |
Displays a list of connected IS-IS routers in all areas, optionally for multicast-intact. |
mpls traffic-eng path-selection ignore overload
To ensure that label switched paths (LSPs) are not disabled when routers have the Intermediate System-to-Intermediate System (IS-IS) overload bit set, use the mpls traffic-eng path-selection ignore overload command in global configuration mode. To disable this override, use the no form of this command.
mpls traffic-eng path-selection ignore overload
no mpls traffic-eng path-selection ignore overload
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values
Command Modes
Global configuration
Command History
|
|
Release 3.7.0 |
This command was introduced on the Cisco CRS-1 and the Cisco XR 12000 Series Router. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
When the IS-IS overload bit avoidance feature is activated, which means that they are still available for use label switched paths (LSPs), all nodes with the overload bit set, including the following nodes, are ignored:
•head nodes
•mid nodes
•tail nodes
Examples
The following example shows how to activate IS-IS overload bit avoidance:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# mpls traffic-eng path-selection ignore overload
The following example shows how to deactivate IS-IS overload bit avoidance:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# no mpls traffic-eng path-selection ignore overload
Related Commands
|
|
set-overload-bit |
Configures a router to signal other routers not to use it as an intermediate hop in their shortest path first (SPF) calculations. |
mpls traffic-eng router-id (IS-IS)
To specify the Multiprotocol Label Switching traffic engineering (MPLS TE) router identifier for the node, use the mpls traffic-eng router-id command in IPv4 address family configuration mode. To disable this feature, use the no form of this command.
mpls traffic-eng router-id {ip-address | interface-type interface-instance}
no mpls traffic-eng [router-id]
Syntax Description
ip-address |
IP address in four-part, dotted-decimal notation. |
interface-type |
Interface type. For more information, use the question mark (?) online help function. |
interface-instance |
Either a physical interface instance or a virtual interface instance as follows: •Physical interface instance. Naming notation is rack/slot/module/port and a slash between values is required as part of the notation. –rack: Chassis number of the rack. –slot: Physical slot number of the modular services card or line card. –module: Module number. A physical layer interface module (PLIM) is always 0. –port: Physical port number of the interface. Note In references to a Management Ethernet interface located on a route processor card, the physical slot number is alphanumeric (RP0 or RP1) and the module is CPU0. Example: interface MgmtEth0/RP1/CPU0/0. •Virtual interface instance. Number range varies depending on interface type. For more information about the syntax for the router, use the question mark (?) online help function. |
Defaults
Global router identifier is used.
Command Modes
IPv4 address family configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The identifier of the router acts as a stable IP address for the traffic engineering configuration. This IP address is flooded to all nodes. For all traffic engineering tunnels originating at other nodes and ending at this node, you must set the tunnel destination to the traffic engineering router ID of the destination node, because that is the address used by the traffic engineering topology database at the tunnel head for its path calculation.
Note We recommend that loopback interfaces be used for MPLS TE, because they are more stable than physical interfaces.
Examples
The following example shows how to specify the traffic engineering router identifier as the IP address associated with loopback interface 0:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# mpls traffic-eng router-id Loopback0
Related Commands
|
|
mpls traffic-eng |
Turns on flooding of MPLS traffic engineering link information in the indicated IGP level or area. |
mpls traffic-eng srlg (IS-IS)
To configure Shared Risk Link Group (SRLG) membership of a link, use the mpls traffic-eng srlg command in global configuration mode. To disable this feature, use the no form of this command.
mpls traffic-eng [type interface-path-id] srlg number
no mpls traffic-eng [type interface-path-id] srlg number
Syntax Description
number |
SRLG membership number. Range is 0 to 4294967295. |
type |
Interface type. For more information, use the question mark (?) online help function. |
interface-path-id |
Physical interface or virtual interface. Note Use the show interfaces command to see a list of all interfaces currently configured on the router. For more information about the syntax for the router, use the question mark (?) online help function. |
Defaults
Shared Risk Link Group memberships are not configured.
Command Modes
Global configuration
Command History
|
|
Release 3.8.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Note We recommend that loopback interfaces be used for MPLS TE, because they are more stable than physical interfaces
|
|
isis |
read, write |
mpls-te |
read, write |
Examples
The following example shows how to configure an SRLG with 10 member links:
RP/0/RP0/CPU0:router(config)#mpls traffic-eng interface gigabitEthernet 0/1/0/1
RP/0/RP0/CPU0:router(config-mpls-te-if)#srlg 10
Related Commands
|
|
mpls traffic-eng |
Turns on flooding of MPLS traffic engineering link information in the indicated IGP level or area. |
net
To configure an Intermediate System-to-Intermediate System (IS-IS) network entity title (NET) for the routing process, use the net command in router configuration mode. To remove the net command from the configuration file and restore the system to its default condition, use the no form of this command.
net network-entity-title
no net network-entity-title
Syntax Description
network-entity-title |
NET that specifies the area address and the system ID for an IS-IS routing process. |
Defaults
No NET is configured. The IS-IS instance is not operational, because a NET is mandatory.
Command Modes
Router configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Under most circumstances, one and only one NET should be configured.
A NET is a network service access point (NSAP) where the last byte is always zero. On a Cisco router running IS-IS, a NET can be 8 to 20 bytes in length. The last byte is always the n-selector and must be zero. The n-selector indicates to which transport entity the packet is sent. An n-selector of zero indicates no transport entity and means that the packet is for the routing software of the system.
The six bytes directly preceding the n-selector are the system ID. The system ID length is a fixed size and cannot be changed. The system ID must be unique throughout each area (Level 1) and throughout the backbone (Level 2).
All bytes preceding the system ID are the area ID.
A maximum of three NETs for each router is allowed. In rare circumstances, it is possible to configure two or three NETs. In such a case, the area this router is in has three area addresses. Only one area still exists, but it has more area addresses.
Configuring multiple NETs can be temporarily useful in network reconfiguration in which multiple areas are merged, or in which one area is split into more areas. Multiple area addresses enable you to renumber an area individually as needed.
Examples
The following example shows how to configure a router with NET area ID 47.0004.004d.0001 and system ID 0001.0c11.1110:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# net 47.0004.004d.0001.0001.0c11.1110.00
Related Commands
nsf (IS-IS)
To enable nonstop forwarding (NSF) on the next restart, use the nsf command in router configuration mode. To restore the default setting, use the no form of this command.
nsf {cisco | ietf}
no nsf {cisco | ietf}
Syntax Description
cisco |
Specifies Cisco proprietary NSF restart. |
ietf |
Specifies Internet Engineering Task Force (IETF) NSF restart. |
Defaults
NSF is disabled.
Command Modes
Router configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
NSF allows an Intermediate System-to-Intermediate System (IS-IS) instance to restart using checkpointed adjacency and link-state packet (LSP) information, and to perform restart with no impact on its neighbor routers. In other words, there is no impact on other routers in the network due to the destruction and recreation of adjacencies and the system LSP.
Examples
The following example shows how to enable Cisco proprietary NSF:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# nsf cisco
Related Commands
|
|
nsf interface-expires |
Configures the number of resends of an an acknowledged NSF-restart acknowledgment. |
nsf interface-timer |
Configures the time interval after which an unacknowledged IETF NSF restart attempt is repeated. |
nsf lifetime (IS-IS) |
Configures the maximum route lifetime following an NSF restart. |
nsf interface-expires
To configure the number of resends of an acknowledged nonstop forwarding (NSF)-restart acknowledgment, use the nsf interface-expires command in router configuration mode. To restore the default value, use the no form of this command.
nsf interface-expires number
no nsf interface-expires
Syntax Description
number |
Number of resends. Range is 1 to 3. |
Defaults
number: 3 resends
Command Modes
Router configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
When a hello packet sent with the NSF restart flag set is not acknowledged, it is re-sent. Use the nsf interface-expires command to control the number of times the NSF hello is re-sent. When this limit is reached on an interface, any neighbor previously known on that interface is assumed to be down and the initial shortest path first (SPF) calculation is permitted, provided that all other necessary conditions are met.
The total time period available for adjacency reestablishment (interface-timer * interface-expires) should be greater than the expected total NSF restart time.
The nsf interface-expires command applies only to Internet Engineering Task Force (IETF)-style NSF. It has no effect if Cisco proprietary NSF is configured.
Examples
The following example shows how to allow only one retry attempt on each interface if an IETF NSF restart signal is not acknowledged:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# nsf ietf
RP/0/RP0/CPU0:router(config-isis)# nsf interface-expires 1
Related Commands
|
|
hello-multiplier |
Specifies the number of IS-IS hello packets a neighbor must miss before the router should declare the adjacency as down. |
nsf interface-timer |
Configures the time interval after which an unacknowledged IETF NSF restart attempt is repeated. |
nsf interface-timer
To configure the time interval after which an unacknowledged Internet Engineering Task Force (IETF) nonstop forwarding (NSF) restart attempt is repeated, use the nsf interface-timer command in router configuration mode. To restore the default value, use the no form of this command.
nsf interface-timer seconds
no nsf interface-timer
Syntax Description
seconds |
NSF restart time interval (in seconds). Range is 3 to 20 seconds. |
Defaults
seconds: 10 seconds
Command Modes
Router configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
When the IETF NSF restart process begins, hello packets send an NSF restart flag that must be acknowledged by the neighbors of the router. Use the nsf interface-timer command to control the restart time interval after the hello packet is re-sent. The restart time interval need not match the hello interval.
The nsf interface-timer command applies only to IETF-style NSF. It has no effect if Cisco proprietary NSF is configured.
Examples
The following example shows how to ensure that a hello packet with the NSF restart flag set is sent again every 5 seconds until the flag is acknowledged:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# nsf ietf
RP/0/RP0/CPU0:router(config-isis)# nsf interface-timer 5
Related Commands
nsf lifetime (IS-IS)
To configure the maximum route lifetime following a nonstop forwarding (NSF) restart, use the nsf lifetime command in router configuration mode. To restore the default value, use the no form of this command.
nsf lifetime seconds
no nsf lifetime
Syntax Description
seconds |
Maximum route lifetime (in seconds) following an NSF restart. Range is 5 to 300 seconds. |
Defaults
seconds: 60 seconds (1 minute)
Command Modes
Router configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the nsf lifetime command to set the maximum available time for the reacquisition of checkpointed adjacencies and link-state packets (LSPs) during a Cisco proprietary NSF restart. LSPs and adjacencies not recovered during this time period are abandoned, thus causing changes to the network topology.
Examples
The following example shows how to configure the router to allow only 20 seconds for the entire NSF process:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# nsf cisco
RP/0/RP0/CPU0:router(config-isis)# nsf lifetime 20
passive (IS-IS)
To suppress Intermediate System-to-Intermediate System (IS-IS) packets from being transmitted to the interface and received packets from being processed on the interface, use the passive command in interface configuration mode. To restore IS-IS packets coming to an interface, use the no form of this command.
passive
no passive
Syntax Description
This command has no arguments or keywords.
Defaults
Interface is active.
Command Modes
Interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following example shows how to configure the router to suppress IS-IS packets on Packet-over-SONET/SDH (POS) interface 0/1/0/1:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface POS0/1/0/1
RP/0/RP0/CPU0:router(config-isis-if)# passive
Related Commands
|
|
suppressed |
Allows the IS-IS interface to participate in forming adjacencies without advertising connected prefixes in the LSPs. |
point-to-point
To configure a network of only two networking devices that use broadcast media and the integrated Intermediate System-to-Intermediate System (IS-IS) routing protocol to function as a point-to-point link instead of a broadcast link, use the point-to-point command in interface configuration mode. To disable the point-to-point usage, use the no form of this command.
point-to-point
no point-to-point
Syntax Description
This command has no arguments or keywords.
Defaults
Interface is treated as broadcast if connected to broadcast media.
Command Modes
Interface configuration
Command History
|
|
Release 3.2 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the point-to-point command only on broadcast media in a network with two networking devices. The command causes the system to issue packets point-to-point rather than as broadcasts. Configure the command on both networking devices in the network.
Examples
The following example shows how to configure a 10-Gb Ethernet interface to act as a point-to-point interface:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface TenGigE 0/6/0/0
RP/0/RP0/CPU0:router(config-isis-if)# point-to-point
priority (IS-IS)
To configure the priority of designated routers, use the priority command in interface configuration mode. To reset the default priority, use the no form of this command.
priority value [level {1 | 2}]
no priority [value] [level {1 | 2}]
Syntax Description
value |
Priority of a router. Range is 0 to 127. |
level {1 | 2} |
(Optional) Specifies routing Level 1 or Level 2 independently. |
Defaults
value: 64
Both Level 1 and Level 2 are configured if no level is specified.
Command Modes
Interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Priorities can be configured for Level 1 and Level 2 independently. Specifying Level 1 or Level 2 resets priority only for Level 1 or Level 2 routing, respectively. Specifying no level allows you to configure all levels.
The priority is used to determine which router on a LAN is the designated router or Designated Intermediate System (DIS). The priorities are advertised in the hello packets. The router with the highest priority becomes the DIS.
In the Intermediate System-to-Intermediate System (IS-IS) protocol, there is no backup designated router. Setting the priority to 0 lowers the chance of this system becoming the DIS, but does not prevent it. If a router with a higher priority comes online, it takes over the role from the current DIS. For equal priorities, the higher MAC address breaks the tie.
Examples
The following example shows how to give Level 1 routing priority by setting the priority level to 80. This router is now more likely to become the DIS.
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface TenGigE0/6/0/0
RP/0/RP0/CPU0:router(config-isis-if)# priority 80 level 1
propagate level
To propagate routes from one Intermediate System-to-Intermediate System (IS-IS) level into another level, use the propagate level command in address family configuration mode. To disable propagation, use the no form of this command.
propagate level {1 | 2} into level {1 | 2} route-policy route-policy-name
no propagate level {1 | 2} into level {1 | 2}
Syntax Description
level {1 | 2} |
Propagates from routing Level 1 or Level 2 routes. |
into |
Propagates from Level 1 or Level 2 routes into Level 1 or Level 2 routes. |
route-policy route-policy-name |
Specifies a configured route policy. |
Defaults
Route leaking (Level 2 to Level 1) is disabled.
Command Modes
Address family configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
The distribute-list access-list-name keyword and argument were changed to route-policy route-policy-name. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
In general, route propagation from Level 1 to Level 2 is automatic. You might want to use this command to better control which Level 1 routes can be propagated into Level 2.
Propagating Level 2 routes into Level 1 is called route leaking. Route leaking is disabled by default. That is, Level 2 routes are not automatically included in Level 1 link-state packets (LSPs). If you want to leak Level 2 routes into Level 1, you must enable that behavior by using this command.
Propagation from Level 1 into Level 1 and from Level 2 into Level 2 is not allowed.
Examples
The following example shows how to redistribute Level 2 routes to Level 1:
RP/0/RP0/CPU0:router(config)# ipv4 access-list 101 permit ip 10.0.0.0 255.0.0.0 10.1.0.1
0.255.255.255
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# net 49.1234.2222.2222.2222.00
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# propagate level 2 into level 1 route-policy policy_a
Related Commands
redistribute (IS-IS)
To redistribute routes from one routing protocol into Intermediate System-to-Intermediate System (IS-IS), use the redistribute command in address family configuration mode. To remove the redistribute command from the configuration file and restore the system to its default condition in which the software does not redistribute routes, use the no form of this command.
Border Gateway Protocol (BGP)
redistribute bgp process-id [level-1 | level-2 | level-1-2] [metric metric-value] [metric-type {internal | external | rib-metric-as-external | rib-metric-as-internal}] [route-policy route-policy-name]
no redistribute bgp process-id [level-1 | level-2 | level-1-2] [metric metric-value] [metric-type {internal | external | rib-metric-as-external | rib-metric-as-internal}] [route-policy route-policy-name]
Connected Routes
redistribute connected [level-1 | level-2 | level-1-2] [metric metric-value] [metric-type {internal | external | rib-metric-as-external | rib-metric-as-internal}] [route-policy route-policy-name]
no redistribute connected [level-1 | level-2 | level-1-2] [metric metric-value] [metric-type {internal | external | rib-metric-as-external | rib-metric-as-internal}] [route-policy route-policy-name]
Intermediate System-to-Intermediate System (IS-IS)
redistribute isis process-id [level-1 | level-2 | level-1-2] [metric metric-value] [metric-type {internal | external | rib-metric-as-external | rib-metric-as-internal}] [route-policy route-policy-name]
no redistribute isis process-id [level-1 | level-2 | level-1-2] [metric metric-value] [metric-type {internal | external | rib-metric-as-external | rib-metric-as-internal}] [route-policy route-policy-name]
Open Shortest Path First (OSPF)
redistribute ospf process-id [level-1 | level-2 | level-1-2] [match {external [1 | 2] | internal | nssa-external [1 | 2]}] [metric metric-value] [metric-type {internal | external | rib-metric-as-external | rib-metric-as-internal}] [route-policy route-policy-name]
no redistribute ospf process-id [level-1 | level-2 | level-1-2] [match {external [1 | 2] | internal | nssa-external [1 | 2]}][metric metric-value] [metric-type {internal | external | rib-metric-as-external | rib-metric-as-internal}] [route-policy route-policy-name]
Open Shortest Path First Version 3 (OSPFv3)
redistribute ospfv3 process-id [level-1 | level-2 | level-1-2] [match {external [1 | 2] | internal | nssa-external [1 | 2]}] [metric metric-value] [metric-type {internal | external | rib-metric-as-external | rib-metric-as-internal}] [route-policy route-policy-name]
no redistribute ospfv3 process-id [level-1 | level-2 | level-1-2] [match {external [1 | 2] | internal | nssa-external [1 | 2]}] [metric metric-value] [metric-type {internal | external | rib-metric-as-external | rib-metric-as-internal}] [route-policy route-policy-name]
Static
redistribute static [level-1 | level-2 | level-1-2] [metric metric-value] [metric-type {internal | external | rib-metric-as-external | rib-metric-as-internal}] [route-policy route-policy-name]
no redistribute static [level-1 | level-2 | level-1-2] [metric metric-value] [metric-type {internal | external | rib-metric-as-external | rib-metric-as-internal}] [route-policy route-policy-name]
Syntax Description
process-id |
For the bgp keyword, an autonomous system number, which is a 16-bit decimal number. Range is 1 to 65535. For the isis keyword, an IS-IS instance identifier from which routes are to be redistributed. For the ospf keyword, an OSPF process name from which routes are to be redistributed. The value takes the form of a string. A decimal number can be entered, but it is stored internally as a string. For the ospfv3 keyword, an OSPFv3 process name from which routes are to be redistributed. The value takes the form of a string. A decimal number can be entered, but it is stored internally as a string. |
level-1 |
(Optional) Specifies that redistributed routes are advertised in the Level-1 LSP of the router. |
level-1-2 |
(Optional) Specifies that redistributed routes are advertised in the Level-1-2 LSP of the router. |
level-2 |
(Optional) Specifies that redistributed routes are advertised in the Level-2 LSP of the router. |
metric metric-value |
(Optional) Specifies the metric used for the redistributed route. Range is 0 to 16777215. The metric-value must be consistent with the IS-IS metric style of the area and topology into which the routes are being redistributed. |
metric-type {internal | external | rib-metric-as-external | rib-metric-as-internal} |
(Optional) Specifies the external link type associated with the route advertised into the ISIS routing domain. It can be one of four values: •internal-Use the internal keyword to set IS-IS internal metric-type •external-Use the external keyword to set IS-IS external metric-type •rib-metric-as-external-Use the rib-metric-as-external keyword to use RIB metric and set IS-IS external metric-type •rib-metric-as-internal-Use the rib-metric-as-internal keyword to use RIB metric and set IS-IS internal metric-type Any route with an internal metric (however large the metric is) is preferred over a route with external metric (however small the metric is). Use the rib-metric-as-external and rib-metric-as-internal keywords to preserve RIB metrics when redistributing routes from another IS-IS router instance or another protocol. |
route-policy route-policy-name |
(Optional) Specifies the identifier of a configured policy. A policy is used to filter the importation of routes from this source routing protocol to IS-IS. |
match {internal | external [1 | 2] | nsaa-external [1 | 2]} |
(Optional) Specifies the criteria by which OSPF routes are redistributed into other routing domains. It can be one or more of the following: •internal—Routes that are internal to a specific autonomous system (intra- and interarea OSPF routes). •external [1 | 2]—Routes that are external to the autonomous system, but are imported into OSPF as Type 1 or Type 2 external routes. •nssa-external [1 | 2]—Routes that are external to the autonomous system, but are imported into OSPF as Type 1 or Type 2 not-so-stubby area (NSSA) external routes. For the external and nssa-external options, if a type is not specified, then both Type 1 and Type 2 are assumed. |
Defaults
Level 2 is configured if no level is specified.
metric-type: internal
match: If no match keyword is specified, all OSPF routes are redistributed.
Command Modes
Address family configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
The policy policy-name keyword and argument were changed to route-policy route-policy-name. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
The rib-metric-as-external and rib-metric-as-internal keywords were added. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Note When redistributing routes (into IS-IS) using both command keywords for setting or matching of attributes and a route policy, the routes are run through the route policy first, followed by the keyword matching and setting.
Use the redistribute command to control the redistribution of routes between separate IS-IS instances. To control the propagation of routes between the levels of a single IS-IS instance, use the propagate level command.
Only IPv4 OSPF addresses can be redistributed into IS-IS IPv4 address families and only IPv6 OSPFv3 prefixes can be distributed into IS-IS IPv6 address families.
Examples
In this example, IS-IS instance isp_A readvertises all of the routes of IS-IS instance isp_B in Level 2 LSP. Note that the level-2 keyword affects which levels instance isp_A advertises the routes in and has no impact on which routes from instance isp_B are advertised (any Level 1 routes from IS-IS instance isp_B are included in the redistribution.
RP/0/RP0/CPU0:router(config)# router isis isp_A
RP/0/RP0/CPU0:router(config-isis)# net 49.1234.2222.2222.2222.00
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# redistribute isis isp_B level-2
RP/0/RP0/CPU0:router(config)# router isis isp_B
RP/0/RP0/CPU0:router(config-isis)# is-type level 1
RP/0/RP0/CPU0:router(config-isis)# net 49.4567.2222.2222.2222.00
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# attached-bit send always-set
Related Commands
retransmit-interval (IS-IS)
To configure the amount of time between retransmission of each Intermediate System-to-Intermediate System (IS-IS) link-state packet (LSP) on a point-to-point link, use the retransmit-interval command in interface configuration mode. To restore the default value, use the no form of this command.
retransmit-interval seconds [level {1 | 2}]
no retransmit-interval [seconds [level {1 | 2}]]
Syntax Description
seconds |
Time (in seconds) between retransmission of each LSP. It is an integer that should be greater than the expected round-trip delay between any two networking devices on the attached network. Range is 0 to 65535 seconds. |
level {1 | 2} |
(Optional) Specifies routing Level 1 or Level 2 independently. |
Defaults
seconds: 5 seconds
Command Modes
Interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The level {1 | 2} keywords were added. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
To prevent needless transmission results, the seconds argument should be conservative.
The retransmit-interval command has no effect on LAN (multipoint) interfaces. On point-to-point links, the value can be increased to enhance network stability.
Because retransmissions occur only when LSPs are dropped, setting this command to a higher value has little effect on reconvergence. The more neighbors networking devices have, and the more paths over which LSPs can be flooded, the higher this value can be made.
Examples
The following example shows how to configure Packet-over-SONET/SDH (POS) interface 0/2/0/1 for retransmission of IS-IS LSPs every 60 seconds for a large serial line:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface POS0/2/0/1
RP/0/RP0/CPU0:router(config-isis-if)# retransmit-interval 60
Related Commands
retransmit-throttle-interval
To configure minimum interval between retransmissions of different Intermediate System-to-Intermediate System (IS-IS) link-state packets (LSPs) on a point-to-point interface, use the retransmit-throttle-interval command in interface configuration mode. To remove the command from the configuration file and restore the system to its default condition, use the no form of this command.
retransmit-throttle-interval milliseconds [level {1 | 2}]
no retransmit-throttle-interval [milliseconds [level {1 | 2}]]
Syntax Description
milliseconds |
Minimum delay (in milliseconds) between LSP retransmissions on the interface. Range is 0 to 65535. |
level {1 | 2} |
(Optional) Specifies routing Level 1 or Level 2 independently. |
Defaults
Default is 0.
Command Modes
Interface configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The level {1 | 2} keywords were added. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the retransmit-throttle-interval command to define the minimum period of time that must elapse between retransmitting any two LSPs on an interface. The retransmit-throttle-interval command may be useful in very large networks with many LSPs and many interfaces as a way of controlling LSP retransmission traffic. This command controls the rate at which LSPs can be re-sent on the interface.
Examples
The following example shows how to configure Packet-over-SONET/SDH (POS) interface 0/2/0/1 to limit the rate of LSP retransmissions to one every 300 milliseconds:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface POS0/2/0/1
RP/0/RP0/CPU0:router(config-isis-if)# retransmit-throttle-interval 300
Related Commands
|
|
lsp-gen-interval |
Configures the minimum interval time between regenerating the same LSP. |
retransmit-interval (IS-IS) |
Configures the amount of time between retransmission of each IS-IS LSP over a point-to-point link. |
router isis
To enable the Intermediate System-to-Intermediate System (IS-IS) routing protocol and to specify an IS-IS instance, use the router isis command in global configuration mode. To disable IS-IS routing, use the no form of this command.
router isis instance-id
no router isis instance-id
Syntax Description
instance-id |
Name of the routing process. Maximum number of characters is 40. |
Defaults
An IS-IS routing protocol is not enabled.
Command Modes
Global configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the router isis command to create an IS-IS routing process. An appropriate network entity title (NET) must be configured to specify the address of the area (Level 1) and system ID of the router. Routing must be enabled on one or more interfaces before adjacencies may be established and dynamic routing is possible.
Multiple IS-IS processes can be configured. Up to eight processes are configurable. A maximum of five IS-IS instances on a system are supported.
Examples
The following example shows how to configure IS-IS for IP routing:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# net 49.0001.0000.0001.00
Related Commands
|
|
net |
Configures an IS-IS NET for the routing process. |
set-attached-bit
Note Effective with Release 3.8.0, the set-attached-bit command is replaced by the attached-bit send command. See the attached-bit send command for more information.
To configure an Intermediate System-to-Intermediate System (IS-IS) instance with an attached bit in the Level 1 link-state packet (LSP), use the set-attached-bit command in address family configuration mode. To remove the set-attached-bit command from the configuration file and restore the system to its default condition, use the no form of this command.
set-attached-bit
no set-attached-bit
Syntax Description
This command has no arguments or keywords.
Defaults
Attached bit is not set in the LSP.
Command Modes
Address family configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
This command was replaced by the attached-bit send command. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the set-attached bit command to set an IS-IS instance with an attached bit in the Level 1 LSP that allows another IS-IS instance to redistribute Level 2 topology. The attached bit is used when the Level 2 connectivity from another IS-IS instance is advertised by the Level 1 attached bit.
Cisco IOS XR software does not support multiple Level 1 areas in a single IS-IS routing instance. But the equivalent functionality is achieved by redistribution of routes between two IS-IS instances by using the redistribute (IS-IS) command.
The attached bit is configured for a specific address family only if the single-topology command is not configured.
Note If connectivity for the Level 2 instance is lost, the attached bit in the Level 1 instance LSP continues sending traffic to the Level 2 instance and causes the traffic to be dropped.
Examples
The following example shows how to set the attached bit for a Level 1 instance that allows the Level 2 instance to redistribute routes from the Level 1 instance:
RP/0/RP0/CPU0:router(config)# router isis 1
RP/0/RP0/CPU0:router(config-isis)# net 49.0001.0001.0001.0001.00
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# redistribute isis 2 level 2
RP/0/RP0/CPU0:router(config-isis-af)# interface POS0/3/0/0
RP/0/RP0/CPU0:router(config-isis-af-if)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config)# router isis 2
RP/0/RP0/CPU0:router(config-isis)# is-type level-1
RP/0/RP0/CPU0:router(config-isis)# net 49.0002.0001.0001.0002.00
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# attached-bit send always-set
RP/0/RP0/CPU0:router(config-isis-af)# interface POS0/1/0/0
RP/0/RP0/CPU0:router(config-isis-af-if)# address-family ipv4 unicast
Related Commands
set-overload-bit
To configure the router to signal other routers not to use it as an intermediate hop in their shortest path first (SPF) calculations, use the set-overload-bit command in router configuration mode. To remove the designation, use t he no form of this command.
set-overload-bit [on-startup {delay | wait-for-bgp}] [level {1 | 2}]
no set-overload-bit [[on-startup {delay | wait-for-bgp}] [level {1 | 2}]]
Syntax Description
on-startup |
(Optional) Sets the overload bit only temporarily after reboot. |
delay |
(Optional) Time (in seconds) to advertise when the router is overloaded after reboot. Range is 5 to 86400 seconds (86400 seconds = 1 day). |
wait-for-bgp |
(Optional) Sets the overload bit on startup until the Border Gateway Protocol (BGP) signals converge or time out. |
level {1 | 2} |
(Optional) Specifies the overload bit for Level 1 or Level 2 independently. |
Defaults
The overload bit is not set.
Both Level 1 and Level 2 are configured if no level is specified.
Command Modes
Router configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the set-overload-bit command to force the router to set the overload bit in its nonpseudonode link-state packets (LSPs). Normally the setting of the overload bit is allowed only when a router experiences problems. For example, when a router is experiencing a memory shortage, the reason might be that the link-state database is not complete, resulting in an incomplete or inaccurate routing table. If the overload bit is set in the LSPs of the unreliable router, other routers can ignore the router in their SPF calculations until it has recovered from its problems. The result is that no paths through the unreliable router are seen by other routers in the Intermediate System-to-Intermediate System (IS-IS) area. However, IP prefixes directly connected to this router are still reachable.
The set-overload-bit command can be useful when you want to connect a router to an IS-IS network, but do not want real traffic flowing through it under any circumstances.
Routers with overload bit set are:
•A test router in the lab, connected to a production network.
•A router configured as an LSP flooding server, for example, on a nonbroadcast multiaccess (NBMA) network, in combination with the mesh group feature.
Examples
The following example shows how to configure the overload bit:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# set-overload-bit
show isis
The show isis [instance instance-id] command displays general information about an IS-IS instance and protocol operation. If the instance ID is not specified, the command shows information about all IS-IS instances.
show isis [instance instance-id]
Syntax Description
instance instance-id |
(Optional) Displays the IS-IS adjacencies for the specified IS-IS instance only. Note The instance-id argument is the instance identifier (alphanumeric) defined by the router isis command. |
Defaults
No instance ID specified displays IS-IS adjacencies for all the IS-IS instances.
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
For each instance, the first line of output lists the IS-IS instance ID with the following lines identifying the IS-IS system ID, supported levels (level 1, level 2, or level-1-2), configured area addresses, active area addresses, status (enabled or not) and type (Cisco or IETF) of nonstop forwarding (NSF), and the mode in which the last IS-IS process startup occurred.
Next, the status of each configured address family (or just IPv4 unicast if none are configured) is summarized. For each level (level 1 or level 2), the metric style (narrow or wide) generated and accepted is listed along with the status of incremental shortest path first (iSPF) computation (enabled or not). Then redistributed protocols are listed, followed by the administrative distance applied to the redistributed routes.
Finally, the running state (active, passive, or disabled) and configuration state (active or disabled) of each IS-IS interface is listed.
Examples
The following is sample output from the show isis command:
RP/0/RP0/CPU0:router#show isis
Wed Aug 20 23:54:55.043 PST DST
System Id: 0000.0000.0002
Routing for area address(es):
Non-stop forwarding: Disabled
Most recent startup mode: Cold Restart
Topologies supported by IS-IS:
Metric style (generate/accept): Narrow/Narrow
No protocols redistributed
Interfaces supported by IS-IS:
Loopback0 is running passively (passive in configuration)
POS0/1/0/2 is running actively (active in configuration)
POS0/1/0/3 is running actively (active in configuration)
Table 1 describes the significant fields shown in the display.
Table 1 show isis Field Descriptions
|
|
IS-IS Router |
IS-IS instance ID. |
System Id |
IS-IS system ID. |
IS Levels |
Supported levels for the instance. |
Manual area address(es) |
Domain and area. |
Routing for area address(es): |
Configured area addresses and active area addresses. |
Non-stop forwarding |
Status (enabled or not) and type (Cisco or IETF) of nonstop forwarding (NSF). |
Most recent startup mode |
The mode in which the last IS-IS process startup occurred. |
Topologies supported by IS-IS |
The summary of the status of each configured address family (or just IPv4 unicast if none are configured). |
Redistributed protocols |
List of redistributed protocols, followed by the administrative distance applied to the redistributed routes. |
Metric style (generate/accept) |
The status of each configured address family (or just IPv4 unicast if none are configured) is summarized. For each level (level 1 or level 2), the metric style (narrow or wide) generated and accepted is listed along with the status of incremental shortest path first (iSPF) computation (enabled or not). |
Interfaces supported by IS-IS |
The running state (active, passive, or disabled) and configuration state (active or disabled) of each IS-IS interface. |
show isis adjacency
To display Intermediate System-to-Intermediate System (IS-IS) adjacencies, use the show isis adjacency command in EXEC mode.
show isis [instance instance-id] adjacency [level {1 | 2}] [interface-type interface-instance] [detail] [systemid system-id]
Syntax Description
instance instance-id |
(Optional) Displays the IS-IS adjacencies for the specified IS-IS instance only. •The instance-id argument is the instance identifier (alphanumeric) defined by the router isis command. |
level {1 | 2} |
(Optional) Displays the IS-IS adjacencies for Level 1 or Level 2 independently. |
interface-type |
Interface type. For more information, use the question mark (?) online help function. |
interface-instance |
Either a physical interface instance or a virtual interface instance as follows: •Physical interface instance. Naming notation is rack/slot/module/port and a slash between values is required as part of the notation. –rack: Chassis number of the rack. –slot: Physical slot number of the modular services card or line card. –module: Module number. A physical layer interface module (PLIM) is always 0. –port: Physical port number of the interface. Note In references to a Management Ethernet interface located on a route processor card, the physical slot number is alphanumeric (RP0 or RP1) and the module is CPU0. Example: interface MgmtEth0/RP1/CPU0/0. •Virtual interface instance. Number range varies depending on interface type. For more information about the syntax for the router, use the question mark (?) online help function. |
detail |
(Optional) Displays neighbor IP addresses and active topologies. |
systemid system-id |
(Optional) Displays the information for the specified router only. |
Defaults
No instance ID specified displays IS-IS adjacencies for all the IS-IS instances.
Both Level 1 and Level 2 are configured if no level is specified.
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following is sample output from the show isis adjacency command:
RP/0/RP0/CPU0:router# show isis adjacency
IS-IS p Level-1 adjacencies:
System Id Interface SNPA State Hold Changed NSF BFD
12a4 PO0/1/0/1 *PtoP* Up 23 00:00:06 Capable Init
12a4 Gi0/6/0/2 0004.2893.f2f6 Up 56 00:04:01 Capable Up
IS-IS p Level-2 adjacencies:
System Id Interface SNPA State Hold Changed NSF BFD
12a4 PO0/1/0/1 *PtoP* Up 23 00:00:06 Capable None
12a4 Gi0/6/0/2 0004.2893.f2f6 Up 26 00:00:13 Capable Init
Table 2 describes the significant fields shown in the display.
Table 2 show isis adjacency Field Descriptions
|
|
Level-1 |
Level 1 adjacencies. |
Level-2 |
Level 2 adjacencies. |
System ID |
Dynamic hostname of the system. The hostname is specified using the hostname command. If the dynamic hostname is not known or hostname dynamic disable command has been executed, the 6-octet system ID is used. |
Interface |
Interface used to reach the neighbor. |
SNPA |
Data-link address (also known as the Subnetwork Point of Attachment [SNPA]) of the neighbor. |
State |
Adjacency state of the neighboring interface. Valid states are: Down, Init, and Up. |
Holdtime |
Hold time of the neighbor. |
Changed |
Time the neighbor has been up (in hours:minutes:seconds). |
NSF |
Specifies whether the neighbor can adhere to the IETF-NSF restart mechanism. |
BFD |
Specifies the Bidirectional Forwarding Detection (BFD) status for the interface. Valid status are: •None—BFD is not configured. •Init—BFD session is not up. One reason is that other side is not yet enabled. •Up—BFD session has been established. •Down—BFD session holdtime expired. |
Related Commands
show isis adjacency-log
To display the Intermediate System-to-Intermediate System (IS-IS) adjacency log, use the show isis adjacency-log command in EXEC mode.
show isis adjacency-log [level {1 | 2}] [last number | first number]
Syntax Description
level {1 | 2} |
(Optional) Displays the IS-IS adjacency log for Level 1 or Level 2 independently. |
last number |
(Optional) Specifies that the output is restricted to the last number of entries. Range is 1 to 100. |
first number |
(Optional) Specifies that the output is restricted to the first number of entries. Range is 1 to 100. |
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following is sample output from the show isis adjacency-log command:
RP/0/RP0/CPU0:router# show isis adjacency-log
IS-IS 10 Level 1 Adjacency log
When System Interface State Details
4d00h 12a1 PO0/5/0/0 d -> i
4d00h 12a1 PO0/5/0/0 i -> u New adjacency
4d00h 12a1 Gi0/6/0/0 d -> u New adjacency
4d00h 12a1 Gi0/6/0/0 u -> d Interface state
3d17h 12a1 Gi0/6/0/0 d -> u New adjacency
3d17h 12a1 Gi0/6/0/0 u -> d Interface state
01:44:07 12a1 Gi0/6/0/0 d -> u New adjacency
IS-IS 10 Level 2 Adjacency log
When System Interface State Details
4d00h 12a1 PO0/5/0/0 d -> i
4d00h 12a1 PO0/5/0/0 i -> u New adjacency
4d00h 12a1 Gi0/6/0/0 d -> u New adjacency
4d00h 12a1 Gi0/6/0/0 u -> d Interface state
3d17h 12a1 Gi0/6/0/0 d -> u New adjacency
3d17h 12a1 Gi0/6/0/0 u -> d Interface state
01:44:07 12a1 Gi0/6/0/0 d -> u New adjacency
Table 3 describes the significant fields shown in the display.
Table 3 show isis adjacency-log Field Descriptions
|
|
When |
Elapsed time (in hh:mm:ss) since the event was logged. |
System |
System ID of the adjacent router. |
Interface |
Specific interface involved in the adjacency change. |
State |
State transition for the logged event. |
Details |
Description of the adjacency change. |
show isis checkpoint adjacency
To display the Intermediate System-to-Intermediate System (IS-IS) checkpoint adjacency database, use the show isis checkpoint adjacency command in EXEC mode.
show isis [instance instance-id] checkpoint adjacency
Syntax Description
instance instance-id |
(Optional) Displays the IS-IS checkpoint adjacencies for the specified IS-IS instance only. •The instance-id argument is the instance identifier (alphanumeric) defined by the router isis command. |
Defaults
No instance ID specified displays IS-IS checkpoint adjacencies for all the IS-IS instances.
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show isis checkpoint adjacency command to display the checkpointed adjacencies. With this information you can restore the adjacency database during a Cisco proprietary nonstop forwarding (NSF) restart. This command, with the show isis adjacency command, may be used to verify the consistency of the two databases.
Examples
The following is sample output from the show isis checkpoint adjacency command:
RP/0/RP0/CPU0:router# show isis checkpoint adjacency
Interface Level System ID State Circuit ID Chkpt ID
POS3/0/0/1 1 router-gsr8 Up 0001.0000.0008.04 80011fec
POS0/4/0/1 1 router-gsr9 Up 0001.0000.0006.01 80011fd8
POS3/0/0/1 2 router-gsr8 Up 0001.0000.0008.04 80011fc4
Table 4 describes the significant fields shown in the display.
Table 4 show isis checkpoint adjacency Field Descriptions
|
|
Interface |
Interface used to reach the neighbor. |
Level |
Lists either routers with Level 1 or Level 2 adjacency configured. |
System ID |
Dynamic hostname of the system. The hostname is specified using the hostname command. If the dynamic hostname is not known or hostname dynamic disable command has been executed, the 6-octet system ID is used. |
State |
State of the neighboring interface. |
Circuit ID |
Unique ID issued to a circuit at its creation. |
Chkpt ID |
Unique ID issued to the checkpoint at its creation. |
Related Commands
show isis checkpoint interface
To display the Intermediate System-to-Intermediate System (IS-IS) checkpoint interfaces, use the show isis checkpoint interface command in EXEC mode.
show isis checkpoint interface
Syntax Description
This command has no arguments or keywords.
Defaults
No default behavior or values
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following is sample output from the show isis checkpoint interface command:
RP/0/RP0/CPU0:router# show isis checkpoint interface
IS-IS 10 checkpoint interface
Interface Index CircNum DIS Areas Chkpt ID
PO0/5/0/0 0 0 NONE 80002fe8
Gi0/6/0/0 1 3 L1L2 80002fd0
Table 5 describes the significant fields shown in the display.
Table 5 show isis checkpoint interface Field Descriptions
|
|
Interface |
Interface used to reach the neighbor. |
Index |
Interface index assigned to an interface upon its creation. |
CircNum |
Unique ID issued to a circuit internally. |
DIS Areas |
Designated Intermediate System area. |
Chkpt ID |
Unique ID issued to the checkpoint at its creation. |
show isis checkpoint lsp
To display the Intermediate System-to-Intermediate System (IS-IS) checkpoint link-state packet (LSP) protocol data unit (PDU) identifier database, use the show isis checkpoint lsp command in EXEC mode.
show isis [instance instance-id] checkpoint lsp
Syntax Description
instance instance-id |
(Optional) Displays the IS-IS checkpoint LSPs for the specified instance only. •The instance-id argument is the instance identifier (alphanumeric) defined by the router isis command. |
Defaults
No instance ID specified displays IS-IS checkpoint LSPs for all the IS-IS instances.
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The checkpointed LSPs displayed by this command are used to restore the LSP database during a Cisco proprietary nonstop forwarding (NSF) restart. The show isis checkpoint lsp command, with the show isis database command, may be used to verify the consistency of the two databases.
Examples
The following is sample output from the show isis checkpoint lsp command:
RP/0/RP0/CPU0:router# show isis checkpoint lsp
1 router-gsr6.00-00 80011f9c
1 router-gsr6.01-00 80011f88
1 router-gsr8.00-00 80011f74
1 router-gsr9.00-00 80011f60
2 router-gsr6.00-00 80011f4c
2 router-gsr6.01-00 80011f38
2 router-gsr8.00-00 80011f24
2 router-gsr9.00-00 80011f10
Total LSP count: 8 (L1: 4, L2 4, local L1: 2, local L2 2)
Table 6 describes the significant fields shown in the display.
Table 6 show isis checkpoint lsp Field Descriptions
|
|
Level |
Routers with Level 1 or Level 2 adjacency configured. |
LSPID |
LSP identifier. The first six octets form the system ID of the router that originated the LSP. The next octet is the pseudonode ID. When this byte is zero, the LSP describes links from the system. When it is nonzero, the LSP is a so-called nonpseudonode LSP. This is similar to a router link-state advertisement (LSA) in the Open Shortest Path First (OSPF) protocol. The LSP describes the state of the originating router. For each LAN, the designated router for that LAN creates and floods a pseudonode LSP, describing all systems attached to that LAN. The last octet is the LSP number. If there is more data than can fit in a single LSP, the LSP is divided into multiple LSP fragments. Each fragment has a different LSP number. An asterisk (*) indicates that the LSP was originated by the system on which this command is issued. |
Chkpt ID |
Unique ID issued to the checkpoint at its creation. |
Related Commands
show isis database
To display the Intermediate System-to-Intermediate System (IS-IS) link-state packet (LSP) database, use the show isis database command in EXEC mode.
show isis [instance instance-id] database [level {1 | 2}] [update] [summary] [detail] [verbose] [* | lsp-id]
Syntax Description
instance instance-id |
(Optional) Displays the IS-IS LSP database for the specified instance only. •The instance-id argument is the instance identifier (alphanumeric) defined by the router isis command. |
level {1 | 2} |
(Optional) Displays the IS-IS LSP database for Level 1 or Level 2 independently. |
update |
(Optional) Displays contents of LSP database managed by update thread. |
summary |
(Optional) Displays the LSP ID number, sequence number, checksum, hold time, and bit information. |
detail |
(Optional) Displays the contents of each LSP. |
verbose |
(Optional) Displays the contents of each LSP. |
* | lsp-id |
(Optional) LSP protocol data units (PDUs) identifier. Displays the contents of a single LSP by its ID number or may contain an * as a wildcard character. |
Defaults
No instance ID specified displays the IS-IS LSP database for all the IS-IS instances.
Both Level 1 and Level 2 is configured if no level is specified.
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
This command was modified to include MPLS Shared Risk Link Groups (SRLG) specific information. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Each of the options for the show isis database command can be entered in an arbitrary string within the same command entry. For example, the following are both valid command specifications and provide the same output: show isis database detail level 2 and show isis database level 2 detail.
The summary keyword used with this command allows you to filter through a large IS-IS database and quickly identify problematic areas.
Examples
The following is sample out from the show isis database command with the summary keyword:
RP/0/RP0/CPU0:router# show isis database summary
IS-IS 10 Database Summary for all LSPs
L1 L2 Total L1 L2 Total L1 L2 Total
----- ----- ----- ----- ----- ----- ----- ----- -----
Router LSPs: 1 1 2 0 0 0 1 1 2
Pseudo-node LSPs: 0 0 0 0 0 0 0 0 0
All LSPs: 1 1 2 0 0 0 1 1 2
ATT bit set LSPs: 0 0 0 0 0 0 0 0 0
OVL bit set LSPs: 0 0 0 0 0 0 0 0 0
Router LSPs: 1 1 2 0 0 0 1 1 2
Pseudo-node LSPs: 0 0 0 0 0 0 0 0 0
All LSPs: 1 1 2 0 0 0 1 1 2
Table 7 describes the significant fields shown in the display.
Table 7 show isis database summary Field Descriptions
|
|
Router LSPs: |
Active, purged, and total LSPs associated with routers. |
Pseudo-node LSPs: |
Active, purged, and total LSPs associated with pseudonodes. |
All LSPs: |
Total active and purged LSPs. |
ATT bit set LSPs |
Attach bit (ATT). Indicates that the router is also a Level 2 router, and it can reach other areas. Level 1-only routers and Level 1-2 routers that have lost connection to other Level 2 routers use the Attach bit to find the closest Level 2 router. They point to a default route to the closest Level 2 router. |
OVL bit set LSPs |
Overload bit. Indicates if the IS is congested. If the Overload bit is set, other routers do not use this system as a transit router when calculating routers. Only packets for destinations directly connected to the overloaded router are sent to this router. |
The following is sample out from the show isis database command with the verbose keyword specified.
RP/0/4/CPU0:router# show isis database verbose
IS-IS test (Level-1) Link State Database
LSPID LSP Seq Num LSP Checksum LSP Holdtime ATT/P/OL
router1.00-00 * 0x00000d44 0x7e2c 535 0/0/0
MT: Standard (IPv4 Unicast)
IP Address: 192.168.0.145
IPv6 Address: 192:168::145
Metric: 10 IS-Extended router1.01
Metric: 10 IS-Extended router2.00
Metric: 10 IS-Extended router2.00
Interface IP Address: 10.3.11.145
Neighbor IP Address: 10.3.11.143
Physical BW: 155520 kbits/sec
Reservable Global pool BW: 0 kbits/sec
Global Pool BW Unreserved:
[0]: 0 kbits/sec [1]: 0 kbits/sec
[2]: 0 kbits/sec [3]: 0 kbits/sec
[4]: 0 kbits/sec [5]: 0 kbits/sec
[6]: 0 kbits/sec [7]: 0 kbits/sec
Interface IP Address: 10.3.11.145
Neighbor IP Address: 10.3.11.143
Metric: 10 IP-Extended 10.3.11.0/24
Metric: 10 IP-Extended 192.168.0.145/32
Metric: 10 MT (IPv6 Unicast) IS-Extended router1.01
Metric: 10 MT (IPv6 Unicast) IPv6 192:168::145/128
Metric: 10 MT (IPv4 Multicast) IS-Extended router1.01
Metric: 10 MT (IPv4 Multicast) IP-Extended 192.168.0.145/32
Metric: 10 MT (IPv6 Multicast) IPv6 192:168::145/128
router1.01-00 0x0000013e 0x3309 1159 0/0/0
Metric: 0 IS-Extended router1.00
Metric: 0 IS-Extended router2.00
Table 8 describes the significant fields shown in the display. As the output shows, the command with the verbose keyword displays the contents of each LSP.
Table 8 show isis database verbose Field Descriptions
|
|
LSPID |
LSP identifier. The first six octets form the system ID of the router that originated the LSP. The next octet is the pseudonode ID. When this byte is zero, the LSP describes links from the system. When it is nonzero, the LSP is a so-called nonpseudonode LSP. This is similar to a router link-state advertisement (LSA) in the Open Shortest Path First (OSPF) protocol. The LSP describes the state of the originating router. For each LAN, the designated router for that LAN creates and floods a pseudonode LSP, describing all systems attached to that LAN. The last octet is the LSP number. If there is more data than can fit in a single LSP, the LSP is divided into multiple LSP fragments. Each fragment has a different LSP number. An asterisk (*) indicates that the LSP was originated by the system on which this command is issued. |
LSP Seq Num |
Sequence number for the LSP that allows other systems to determine if they have received the latest information from the source. |
LSP Checksum |
Checksum of the entire LSP packet. |
LSP Holdtime |
Time the LSP remains valid (in seconds). An LSP hold time of zero indicates that this LSP was purged and is being removed from the link-state database (LSDB) of all routers. The value indicates how long the purged LSP stays in the LSDB before being completely removed. |
ATT/P/OL |
ATT—Attach bit. This bit indicates that the router is also a Level 2 router, and it can reach other areas. Level 1-only routers and Level 1-2 routers that have lost connection to other Level 2 routers use the Attach bit to find the closest Level 2 router. They point to a default route to the closest Level 2 router. P—P bit. Detects if the intermediate system is area partition repair capable. Cisco and other vendors do not support area partition repair. OL—Overload bit. Determines if the IS is congested. If the Overload bit is set, other routers do not use this system as a transit router when calculating routers. Only packets for destinations directly connected to the overloaded router are sent to this router. |
Area Address |
Reachable area addresses from the router. For Level 1 LSPs, these are the area addresses configured manually on the originating router. For Level 2 LSPs, these are all the area addresses for the area to which this route belongs. |
NLPID |
Network Layer Protocol Identifier. |
Hostname |
Hostname of the node. |
IP Address |
IP address of the node. |
Metric |
IS-IS metric for the cost of the adjacency between the originating router and the advertised neighbor, or the metric of the cost to get from the advertising router to the advertised destination (which can be an IP address, an end system (ES), or a Connectionless Network Service (CLNS) prefix). |
MPLS SRLG |
MPLS SRLG TLV information per neighbor, identified by hostname or system ID. |
Interface IP Address |
Local interface IP address. |
Neighbor IP Address |
Remote interface IP address. |
Flags |
Flags carried in SRLG TLV. The Least Significant Bit (LSB) is set if the interface is numbered. |
SRLGs |
SRLG values. |
show isis database-log
To display the entries in the Intermediate System-to-Intermediate System (IS-IS) database log, use the show isis database-log command in EXEC mode.
show isis database-log [level {1 | 2}] [last number | first number]
Syntax Description
level {1 | 2} |
(Optional) Displays the database log for Level 1 or Level 2 independently. |
last number |
(Optional) Specifies that the output is restricted to the last number of entries. Range is 1 to 1000. |
first number |
(Optional) Specifies that the output is restricted to the first number of entries. Range is 1 to 1000. |
Defaults
Both Level 1 and Level 2 are configured if no level is specified.
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following is sample output from the show isis database-log command:
RP/0/RP0/CPU0:router# show isis database-log
IS-IS 10 Level 1 Link State Database Log
WHEN LSPID Op Seq Num Holdtime OL Seq Num Holdtime OL
01:17:19 12b1.03-00 REP 0x00000003 1200 0 0x00000002 340 0
001:06:20 12b1.00-00 REP 0x000001d8 1200 0 0x000001d7 375 0
01:06:00 12b1.03-00 REP 0x00000004 1200 0 0x00000003 520 0
01:05:46 12a1.00-00 REP 0x000001fc 1200 0 0x000001fb 425 0
00:55:01 12b1.00-00 REP 0x000001d9 1200 0 0x000001d8 520 0
00:53:39 12b1.03-00 REP 0x00000005 1200 0 0x00000004 459 0
00:53:19 12a1.00-00 REP 0x000001fd 1200 0 0x000001fc 453 0
00:42:12 12b1.00-00 REP 0x000001da 1200 0 0x000001d9 431 0
00:39:56 12b1.03-00 REP 0x00000006 1200 0 0x00000005 376 0
00:38:54 12a1.00-00 REP 0x000001fe 1200 0 0x000001fd 334 0
00:29:10 12b1.00-00 REP 0x000001db 1200 0 0x000001da 418 0
00:27:22 12b1.03-00 REP 0x00000007 1200 0 0x00000006 446 0
00:25:10 12a1.00-00 REP 0x000001ff 1200 0 0x000001fe 375 0
00:17:04 12b1.00-00 REP 0x000001dc 1200 0 0x000001db 473
Table 9 describes the significant fields shown in the display.
Table 9 show isis database-log Field Descriptions
|
|
WHEN |
Elapsed time (in hh:mm:ss) since the event was logged. |
LSPID |
LSP identifier. The first six octets form the system ID of the router that originated the LSP. The next octet is the pseudonode ID. When this byte is zero, the LSP describes links from the system. When it is nonzero, the LSP is a so-called nonpseudonode LSP. This is similar to a router link-state advertisement (LSA) in the Open Shortest Path First (OSPF) protocol. The LSP describes the state of the originating router. For each LAN, the designated router for that LAN creates and floods a pseudonode LSP, describing all systems attached to that LAN. The last octet is the LSP number. If there is more data than can fit in a single LSP, the LSP is divided into multiple LSP fragments. Each fragment has a different LSP number. An asterisk (*) indicates that the LSP was originated by the system on which this command is issued. |
New LSP |
New router or pseudonode appearing in the topology. |
Old LSP |
Old router or pseudonode leaving the topology. |
Op |
Operation on the database: inserted (INS) or replaced (REP). |
Seq Num |
Sequence number for the LSP that allows other systems to determine if they have received the latest information from the source. |
Holdtime |
Time the LSP remains valid (in seconds). An LSP hold time of zero indicates that this LSP was purged and is being removed from the link-state database (LSDB) of all routers. The value indicates how long the purged LSP stays in the LSDB before being completely removed. |
OL |
Overload bit. Determines if the IS is congested. If the Overload bit is set, other routers do not use this system as a transit router when calculating routers. Only packets for destinations directly connected to the overloaded router are sent to this router. |
Related Commands
show isis hostname
To display the entries in the Intermediate System-to-Intermediate System (IS-IS) router name-to-system ID mapping table, use the show isis hostname command in EXEC mode.
show isis [instance instance-id] hostname
Syntax Description
instance instance-id |
(Optional) Displays the IS-IS router name-to-system ID mapping table for the specified IS-IS instance only. The instance-id argument is the instance identifier (alphanumeric) defined by the router isis command. |
Defaults
No instance ID specified displays the IS-IS router name-to-system ID mapping table for all the IS-IS instances.
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The show isis hostname command does not display entries if the dynamic hostnames are disabled.
Examples
The following is sample output from the show isis hostname command with the instance and instance-id values specified:
RP/0/RP0/CPU0:router# show isis instance isp hostname
Level System ID Dynamic Hostname
2 * 0001.0000.0011 router-11
Table 10 describes the significant fields shown in the display.
Table 10 show isis instance isp hostname Field Descriptions
|
|
Level |
IS-IS level of the router. |
System ID |
Dynamic hostname of the system. The hostname is specified using the hostname command. If the dynamic hostname is not known or hostname dynamic disable command has been executed, the 6-octet system ID is used. |
Dynamic Hostname |
Hostname of the router. |
* |
Local router. |
Related Commands
|
|
hostname |
Specifies the name of the local router. |
hostname dynamic disable |
Enables the IS-IS routing protocol to dynamically update the mapping of router names to system IDs. |
show isis interface
To display information about the Intermediate System-to-Intermediate System (IS-IS) interfaces, use the show isis interface command in EXEC mode.
show isis interface [type interface-path-id | level {1 | 2}] [brief]
Syntax Description
type |
Interface type. For more information, use the question mark (?) online help function. |
interface-path-id |
Physical interface or virtual interface. Note Use the show interfaces command to see a list of all interfaces currently configured on the router. For more information about the syntax for the router, use the question mark (?) online help function. |
level {1 | 2} |
(Optional) Displays IS-IS interface information for Level 1 or Level 2 independently. |
brief |
(Optional) Displays brief interface output. |
Defaults
Displays all IS-IS interfaces.
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following is sample output from the show isis interface command:
RP/0/5/CPU0:router#show isis interface POS 0/3/0/2
Adjacency Formation: Enabled
Prefix Advertisement: Enabled
Circuit Type: level-2-only
Extended Circuit Number: 67111168
LSP Pacing Interval: 33 ms
IPv4 Unicast Topology: Enabled
Adjacency Formation: Running
Prefix Advertisement: Running
MPLS LDP Sync (L1/L2): Disabled/Disabled
IPv6 Unicast Topology: Disabled (Not cfg on the intf)
IPv4 Address Family: Enabled
Forwarding Address(es): 10.3.10.143
Global Prefix(es): 10.3.10.0/24
IPv6 Address Family: Disabled (No topology enabled which uses IPv6)
LSP transmit timer expires in 0 ms
Can send up to 9 back-to-back LSPs in the next 0 ms
Table 11 describes the significant fields shown in the display.
Table 11 show isis interface Field Descriptions
|
|
GigabitEthernet0/6/0/0 |
Status of the interface, either enabled or disabled. |
Adjacency formation: |
Status of adjacency formation, either enabled or disabled. |
Prefix Advertisement: |
Status of advertising connected prefixes, either enabled or disabled. |
BFD: |
Status of Bidirectional Forwarding Detection (BFD), either enabled or disabled. |
BFD Min Interval: |
BFD minimum interval. |
BFD Multiplier: |
BFD multiplier. |
Circuit Type: |
Levels the interface is running on (circuit-type configuration) which may be a subset of levels on the router. |
Media Type: |
Media type on which IS-IS is running. |
Circuit Number: |
Unique ID assigned to a circuit internally (8-bit integer). |
Extended Circuit Number: |
Valid only for point-to-point interfaces (32-bit integer). |
LSP Rexmit Queue Size: |
Number of LSPs pending retransmission on the interface. |
Adjacency Count: |
Number of adjacencies formed with a neighboring router that supports the same set of protocols. |
PSNP Entry Queue Size: |
Number of SNP entries pending inclusion in the next PSNP. |
LAN ID: |
ID of the LAN. |
Priority (Local/DIS): |
Priority of this interface or priority of the Designated Intermediate System. |
Next LAN IIH in: |
Time (in seconds) in which the next LAN hello message is sent. |
LSP Pacing Interval: |
Interval at which the link-state packet (LSP) transmission rate (and by implication the reception rate of other systems) is to be reduced. |
Protocol State: |
Running state of the protocol (up or down). |
MTU: |
Link maximum transmission unit (MTU). |
SNPA: |
Data-link address (also known as the Subnetwork Point of Attachment [SNPA]) of the neighbor. |
All Level-n ISs: |
Status of interface membership in Layer 2 multicast group. The status options are Yes or reason for not being a member of the multicast group. |
IPv4 Unicast Topology: |
Status of the topology, either enabled or disabled. |
Adjacency Formation: |
Status of adjacency formation. The status options are Running or a reason for not being ready to form adjacencies. |
Prefix Advertisement: |
Status of advertising prefixes, either enabled or disabled. |
Metric (L1/L2): |
IS-IS metric for the cost of the adjacency between the originating router and the advertised neighbor, or the metric of the cost to get from the advertising router to the advertised destination (which can be an IP address, an end system (ES), or a connectionless network service (CLNS) prefix). |
MPLS LDP Sync (L1/L2) |
Status of LDP IS-IS synchronization, either enabled or disabled. When enabled, the state of synchronization (Sync Status) is additionally displayed as either achieved or not achieved. |
IPv4 Address Family: |
Status of the address family, either enabled or disabled. |
Protocol State: |
State of the protocol. |
Forwarding Address(es): |
Addresses on this interface used by the neighbor for next-hop forwarding. |
Global Prefix(es): |
Prefixes for this interface included in the LSP. |
LSP transmit timer expires in |
LSP transmission expiration timer interval (in milliseconds). |
LSP transmission is |
State of LSP transmission. Valid states are: •idle •in progress •requested •requested and in progress |
The following is sample output from the show isis interface command with the brief keyword:
RP/0/0/CPU0:router# show isis interface brief
Interface All Adjs Adj Topos Adv Topos CLNS MTU Prio
OK L1 L2 Run/Cfg Run/Cfg L1 L2
----------------- --- --------- --------- --------- ---- ---- --------
PO0/5/0/0 Yes 1 1 1/1 1/1 Up 4469 - -
Gi0/6/0/0 Yes 1* 1* 1/1 1/1 Up 1497 64 64
Table 12 describes the significant fields shown in the display.
Table 12 show isis interface brief Field Descriptions
|
|
Interface |
Name of the interface. |
All OK |
Everything is working as expected for this interface. |
Adjs L1 L2 |
Number of L1 and L2 adjacencies over this interface. |
Adj Topos Run/Cfg |
Number of topologies that participate in forming adjacencies. Number of topologies that were configured to participate in forming adjacencies. |
Adv Topos Run/Cfg |
Number of topologies that participate in advertising prefixes. Number of topologies that were configured to participate in advertising prefixes. |
CLNS |
Status of the Connectionless Network Service. Status options are Up or Down. |
MTU |
Maximum transfer unit size for the interface. |
Prio L1 L2 |
Interface L1 priority. Interface L2 priority. |
show isis lsp-log
To display link-state packet (LSP) log information, use the show isis lsp-log command in EXEC mode.
show isis [instance instance-id] lsp-log [level {1 | 2}] [last number | first number]
Syntax Description
instance instance-id |
(Optional) Displays the LSP log information for the specified IS-IS instance only. •The instance-id argument is the instance identifier (alphanumeric) defined by the router isis command. |
level {1 | 2} |
(Optional) Displays the Intermediate System-to-Intermediate System (IS-IS) link-state database for Level 1 or Level 2 independently. |
last number |
(Optional) Specifies that the output is restricted to the last number of entries. Range is 1 to 20. |
first number |
(Optional) Specifies that the output is restricted to the first number of entries. Range is 1 to 20. |
Defaults
No instance ID specified displays the LSP log information for all the IS-IS instances.
Both Level 1 and Level 2 are configured if no level is specified.
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following is sample output from the show isis lsp-log command with the instance and instance-id values specified:
RP/0/RP0/CPU0:router# show isis instance isp lsp-log
When Count Interface Triggers
When Count Interface Triggers
Table 13 describes the significant fields shown in the display.
Table 13 show isis instance isp lsp-log Field Descriptions
|
|
Level |
IS-IS level of the router. |
When |
How long ago (in hh:mm:ss) an LSP rebuild occurred. The last 20 occurrences are logged. |
Count |
Number of events that triggered this LSP run. When there is a topology change, often multiple LSPs are received in a short period. A router waits 5 seconds before running a full LSP, so it can include all new information. This count denotes the number of events (such as receiving new LSPs) that occurred while the router was waiting its 5 seconds before running full LSP. |
Interface |
Interface that corresponds to the triggered reasons for the LSP rebuild. |
Triggers |
A list of all reasons that triggered an LSP rebuild. The triggers are: •AREASET—area set changed •ATTACHFLAG—bit attached •CLEAR—clear command •CONFIG—configuration change •DELADJ—adjacency deleted •DIS—DIS changed •IFDOWN—interface down •IPADDRCHG—IP address change •IPDEFORIG—IP def-orig •IPDOWN—connected IP down •IFDOWN—interface down •IPEXT—external IP •IPIA—interarea IP •IPUP—connected IP up •LSPDBOL—LSPDBOL bit •LSPREGEN—LSP regeneration •NEWADJ—new adjacency |
show isis mesh-group
To display Intermediate System-to-Intermediate System (IS-IS) mesh group information, use the show isis mesh-group command in EXEC mode.
show isis [instance instance-id] mesh-group
Syntax Description
instance instance-id |
(Optional) Displays the mesh group information for the specified IS-IS instance only. •The instance-id argument is the instance identifier (alphanumeric) defined by the router isis command. |
Defaults
No instance ID specified displays the IS-IS mesh group information for all the IS-IS instances.
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following is sample output from the show isis mesh-group command with the instance and instance-id values specified:
RP/0/RP0/CPU0:router# show isis instance isp mesh-group
Table 14 describes the significant fields shown in the display.
Table 14 show isis instance isp mesh-group Field Descriptions
|
|
Mesh group |
Mesh group number to which this interface is a member. A mesh group optimizes link-state packet (LSP) flooding in nonbroadcast multiaccess (NBMA) networks with highly meshed, point-to-point topologies. LSPs that are first received on interfaces that are part of a mesh group are flooded to all interfaces except those in the same mesh group. |
POS0/4/0/1 |
Interface belonging to mesh group 6. |
show isis mpls traffic-eng adjacency-log
To display a log of Multiprotocol Label Switching traffic engineering (MPLS TE) adjacency changes for an Intermediate System-to-Intermediate System (IS-IS) instance, use the show isis mpls traffic-eng adjacency-log command in EXEC mode.
show isis [instance instance-id] mpls traffic-eng adjacency-log [last number | first number]
Syntax Description
instance instance-id |
(Optional) Displays the MPLS TE adjacency changes for the specified IS-IS instance only. •The instance-id argument is the instance identifier (alphanumeric) defined by the router isis command. |
last number |
(Optional) Specifies that the output is restricted to last number of entries. Range is 1 to 20. |
first number |
(Optional) Specifies that the output is restricted to first number of entries. Range is 1 to 20. |
Defaults
No instance ID specified displays MPLS TE adjacency changes for all the IS-IS instances.
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The last number and first number keywords and arguments were added. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show isis mpls traffic-eng adjacency-log command to display the status of MPLS TE adjacencies.
Examples
The following is sample output from the show isis mpls traffic-eng adjacency-log command with the instance and instance-id values specified:
RP/0/RP0/CPU0:router# show isis instance isp mpls traffic-eng adjacency-log
IS-IS isp Level-2 MPLS Traffic Engineering adjacency log
When Neighbor ID IP Address Interface Status
00:03:36 router-6 172.17.1.6 PO0/3/0/1 Up
00:03:36 router-6 172.17.1.6 PO0/3/0/1 Down
00:02:38 router-6 172.17.1.6 PO0/3/0/1 Up
Table 15 describes the significant fields shown in the output.
Table 15 show isis instance isp mpls traffic-eng adjacency-log Field Descriptions
|
|
When |
Time (in hh:mm:ss) since the entry was recorded in the log. |
Neighbor ID |
Identification value of the neighbor. |
IP Address |
Neighbor IP Version 4 (IPv4) address. |
Interface |
Interface from which a neighbor is learned. |
Status |
Up (active) or Down (disconnected). |
Related Commands
show isis mpls traffic-eng advertisements
To display the latest flooded record from Multiprotocol Label Switching traffic engineering (MPLS TE) for an Intermediate System-to-Intermediate System (IS-IS) instance, use the show isis mpls traffic-eng advertisements command in EXEC mode.
show isis [instance instance-id] mpls traffic-eng advertisements
Syntax Description
instance instance-id |
(Optional) Displays the latest flooded record from MPLS TE for the specified IS-IS instance only. •The instance-id argument is the instance identifier (alphanumeric) defined by the router isis command. |
Defaults
No instance ID specified displays the latest flooded record from MPLS TE for all the IS-IS instances.
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show isis mpls traffic-eng advertisements command to verify that MPLS TE is flooding its record and that the bandwidths are correct.
Examples
The following is sample output from the show isis mpls traffic-eng advertisements command with the instance and instance-id values specified:
RP/0/RP0/CPU0:router# show isis instance isp mpls traffic-eng advertisements
ISIS isp Level-2 MPLS Traffic Engineering advertisements
Neighbor System ID: router-gsr6 (P2P link)
Interface IP address: 172.18.0.9
Neighbor IP Address: 172.18.0.6
Physical BW: 155520000 bits/sec
Reservable BW global: 10000000 bits/sec
Reservable BW sub: 0 bits/sec
Global pool BW unreserved:
[0]: 10000000 bits/sec, [1]: 10000000 bits/sec
[2]: 10000000 bits/sec, [3]: 10000000 bits/sec
[4]: 10000000 bits/sec, [5]: 10000000 bits/sec
[6]: 10000000 bits/sec, [7]: 10000000 bits/sec
[0]: 0 bits/sec, [1]: 0 bits/sec
[2]: 0 bits/sec, [3]: 0 bits/sec
[4]: 0 bits/sec, [5]: 0 bits/sec
[6]: 0 bits/sec, [7]: 0 bits/sec
Affinity Bits: 0x00000000
Table 16 describes the significant fields shown in the output.
Table 16 show isis instance isp mpls traffic-eng advertisements Field Descriptions
|
|
System ID |
Dynamic hostname of the system. The hostname is specified using the hostname command. If the dynamic hostname is not known or hostname dynamic disable command has been executed, the 6-octet system ID is used. |
Router ID |
MPLS TE router ID. |
Link Count |
Number of links that MPLS TE advertised. |
Neighbor System ID |
System ID of a neighbor number in an area. The six bytes directly preceding the n-selector are the system ID. The system ID length is a fixed size and cannot be changed. The system ID must be unique throughout each area (Level 1) and throughout the backbone (Level 2). In an IS-IS routing domain, each router is represented by a 6-byte hexadecimal system ID. When network administrators maintain and troubleshoot networking devices, they must know the router name and corresponding system ID. |
Interface IP address |
IP address of the interface. |
Neighbor IP Address |
IP address of the neighbor. |
Admin. Weight |
Administrative weight associated with this link. |
Physical BW |
Link bandwidth capacity (in bits per second). |
Reservable BW |
Reservable bandwidth on this link. |
Global pool BW unreserved |
Unreserved bandwidth that is available in the global pool. |
Sub pool BW unreserved |
Amount of unreserved bandwidth that is available in the subpool. |
Affinity Bits |
Link attribute flags being flooded. Bits are MPLS-TE specific. |
Related Commands
show isis mpls traffic-eng tunnel
To display Multiprotocol Label Switching traffic engineering (MPLS TE) tunnel information for an Intermediate System-to-Intermediate System (IS-IS) instance, use the show isis mpls traffic-eng tunnel command in EXEC mode.
show isis [instance instance-id] mpls traffic-eng tunnel
Syntax Description
instance instance-id |
(Optional) Displays the MPLS TE tunnel information for the specified IS-IS instance only. •The instance-id argument is the instance identifier (alphanumeric) defined by the router isis command. |
Defaults
No instance ID specified displays the MPLS TE tunnel information for all the IS-IS instances.
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show isis command to find the current status of MPLS TE tunnels.
Tunnels are used in IS-IS next-hop calculations.
Examples
The following is sample output from the show isis mpls traffic-eng tunnel command:
RP/0/RP0/CPU0:router# show isis mpls traffic-eng tunnel
ISIS isp Level-2 MPLS Traffic Engineering tunnels
System Id Tunnel Name Bandwidth Nexthop Metric Mode
router-6 tu0 100000 172.18.1.6 0 Relative
Table 17 describes the significant fields shown in the display.
Table 17 show isis mpls traffic-eng tunnel Field Descriptions
|
|
System ID |
Dynamic hostname of the system. The hostname is specified using the hostname command. If the dynamic hostname is not known or hostname dynamic disable command has been executed, the 6-octet system ID is used. |
Tunnel Name |
Name of the MPLS TE tunnel interface. |
Bandwidth |
MPLS TE-specified tunnel bandwidth of the tunnel. |
Nexthop |
MPLS TE destination IP address of the tunnel. |
Metric |
MPLS TE metric of the tunnel. |
Mode |
MPLS TE metric mode of the tunnel. It can be relative or absolute. |
show isis neighbors
To display information about Intermediate System-to-Intermediate System (IS-IS) neighbors, use the show isis neighbors command in EXEC mode.
show isis [instance instance-id] neighbors [interface-type interface-number | summary] [detail] [systemid system-id]
Syntax Description
instance instance-id |
(Optional) Displays the IS-IS neighbor information for the specified IS-IS instance only. •The instance-id argument is the instance identifier (alphanumeric) defined by the router isis command. |
interface-type |
(Optional) Interface type. For more information, use the question mark (?) online help function. |
interface-number |
(Optional) Interface number. For more information about the numbering syntax for the router, use the question mark (?) online help function. No space is required between the interface-type and interface-number values. |
summary |
(Optional) Displays neighbor status count for each level. |
detail |
(Optional) Displays additional details. |
systemid system-id |
(Optional) Displays the information for the specified neighbor only. |
Defaults
No instance ID specified displays neighbor information for all the IS-IS instances.
Both Level 1 and Level 2 are configured if no level is specified.
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following is sample output from the show isis neighbors command with the instance and instance-id values specified:
RP/0/RP0/CPU0:router# show isis instance isp neighbors detail
System Id Interface SNPA State Holdtime Type IETF-NSF
e222e Gi0/1/0/0 *PtoP* Up 23 L1 Capable
IPv4 Address(es): 10.1.0.45*
IPv6 Address(es): fe80::212:daff:fe6b:68a8*
Topologies: 'IPv4 Unicast' 'IPv6 Unicast'
IPFRR: LFA Neighbor: elise
LFA IPv4 address: 10.100.1.2
LFA Router address: 192.168.0.45
LFA Interface: Gi0/1/0/0.1
e333e Gi0/1/0/0.1 0012.da6b.68a8 Up 8 L1 Capable
IPv4 Address(es): 10.100.1.2*
Topologies: 'IPv4 Unicast'
IPFRR: LFA Neighbor: elise
LFA IPv4 address: 10.1.0.45
LFA Router address: 192.168.0.45
m44i Gi0/1/0/1 0012.da62.e0a8 Up 7 L1 Capable
IPv4 Address(es): 10.1.2.47*
IPv6 Address(es): fe80::212:daff:fe62:e0a8*
Topologies: 'IPv4 Unicast' 'IPv6 Unicast'
Table 18 describes the significant fields shown in the display.
Table 18 show isis instance isp neighbors Field Descriptions
|
|
System ID |
Dynamic hostname of the system. The hostname is specified using the hostname command. If the dynamic hostname is not known or hostname dynamic disable command has been executed, the 6-octet system ID is used. |
Interface |
Interface through which the neighbor is reachable. |
SNPA |
Data-link address (also known as the Subnetwork Point of Attachment [SNPA]) of the neighbor. |
State |
Adjacency state of the neighboring interface. Valid states are: Down, Init, and Up. |
Holdtime |
Hold time of the neighbor. |
Type |
Type of adjacency. |
IETF-NSF |
Specifies whether the neighbor can adhere to the IETF-NSF restart mechanism. Valid states are Capable and Unable. |
Area Address(es) |
Number of area addresses on this router. |
IPv4 Address(es) |
IPv4 addresses configured on this router. |
Topologies |
Address and subaddress families for which IS-IS is configured. |
Uptime |
Time (in hh:mm:ss) that the neighbor has been up. |
IPFRR: LFA Neighbor |
IP fast reroute (IPFRR) loop-free alternate (LFA) neighbor. |
LFA IPv4 address: |
Address of the LFA. |
LFA Interface: |
LFA interface. |
The following is sample output from the show isis neighbors command with the summary keyword specified:
RP/0/RP0/CPU0:router# show isis instance isp neighbors summary
ISIS isp neighbor summary:
Table 19 describes the significant fields shown in the display.
Table 19 show isis neighbors summary Field Descriptions
|
|
State |
State of the neighbor is up, initialized, or failed. |
L1 |
Number of Level 1 neighbors. |
L2 |
Number of Level 2 neighbors. |
L1L2 |
Number of Level 1 and 2 neighbors. |
Related Commands
show isis protocol
To display summary information about an Intermediate System-to-Intermediate System (IS-IS) instance, use the show isis protocol command in EXEC mode.
show isis [instance instance-id] protocol
Syntax Description
instance instance-id |
(Optional) Displays the IS-IS adjacencies for the specified IS-IS instance only. •The instance-id argument is the instance identifier (alphanumeric) defined by the router isis command. |
Defaults
No instance ID specified displays IS-IS adjacencies for all the IS-IS instances.
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following is sample output from the show isis protocol command:
RP/0/RP0/CPU0:router# show isis protocol
System Id: 0001.0000.0011
Routing for area address(es):
Non-stop forwarding: Cisco Proprietary NSF Restart enabled
Process startup mode: Cold Restart
Topologies supported by IS-IS:
Level-1 iSPF status: Dormant (awaiting initial convergence)
Level-2 iSPF status: Dormant (awaiting initial convergence)
No protocols redistributed
Interfaces supported by IS-IS:
Loopback0 is running passively (passive in configuration)
POS0/4/0/1 is running actively (active in configuration)
POS0/5/0/1 is running actively (active in configuration)
Table 20 describes the significant fields shown in the display.
Table 20 show isis protocol Field Descriptions
|
|
System ID: |
Dynamic hostname of the system. The hostname is specified using the hostname command. If the dynamic hostname is not known or hostname dynamic disable command has been executed, the 6-octet system ID is used. |
IS Levels: |
IS-IS level of the router. |
Manual area address(es) |
Area addresses that are manually configured. |
Routing for area address(es) |
Area addresses for which this router provides the routing. |
Non-stop forwarding: |
Status and name of nonstop forwarding (NSF). |
Process startup mode: |
Mode in which the last process startup occurred. Valid modes are: •Cisco Proprietary NSF Restart •IETF NSF Restart •Cold Restart |
iSPF status: |
State of incremental shortest path first (iSPF) configuration for this IS-IS instance. Four states exist: Disabled if iSPF has not been configured but is awaiting a full SPF to compile the topology for use by the iSPF algorithm. Dormant if iSPF has been configured but is awaiting initial convergence before initializing. Awake if iSPF has been configured but is awaiting a full SPF to compile the topology for use by the iSPF algorithm. Active if IS-IS is ready to consider using the iSPF algorithm whenever a new route calculation needs to be run. |
No protocols redistributed: |
No redistributed protocol information exists to be displayed. |
Distance: |
Administrative distance for this protocol. |
show isis route
To display IP reachability information for an Intermediate System-to-Intermediate System (IS-IS) instance, use the show isis route command in EXEC mode.
show isis [instance instance-id] [[ipv4 | ipv6 | afi-all] [unicast | multicast [topology {all | topo-name}] | safi-all]] route [ip-address mask | ip-address/length [longer-prefixes]] [summary] [multicast-intact] [backup] [detail]
Syntax Description
instance instance-id |
(Optional) Displays the IP reachability information for the specified IS-IS instance only. •The instance-id argument is the instance identifier (alphanumeric) defined by the router isis command. |
ipv4 |
(Optional) Specifies IP Version 4 address prefixes. |
ipv6 |
(Optional) Specifies IP Version 6 address prefixes. |
afi-all |
(Optional) Specifies all address prefixes. |
unicast |
(Optional) Specifies unicast address prefixes. |
multicast |
(Optional) Specifies multicast address prefixes. |
topology |
(Optional) Specifies IS-IS paths to intermediate systems. |
topology topo-name |
(Optional) Specifies topology table information and name of the topology table. |
safi-all |
(Optional) Specifies all secondary address prefixes. |
ip-address |
(Optional) Network IP address about which routing information should be displayed. |
mask |
(Optional) Network mask specified in either of two ways: •Network mask can be a four-part, dotted decimal address. For example, 255.0.0.0 indicates that each bit equal to 1 means the corresponding address bit is a network address. •Network mask can be indicated as a slash (/) and number. For example, /8 indicates that the first 8 bits of the mask are ones, and the corresponding bits of the address are the network address. |
/length |
(Optional) Length of the IP prefix. A decimal value that indicates how many of the high-order contiguous bits of the address compose the prefix (the network portion of the address). A slash must precede the decimal value. Range is 0 to 32 for IPv4 addresses and 0 to 128 for IPv6 addresses. |
longer-prefixes |
(Optional) Displays route and more-specific routes. |
summary |
(Optional) Displays topology summary information. |
multicast-intact |
(Optional) Displays multicast intact information for this entry. |
systemid |
(Optional) Displays multicast information by system ID. |
backup |
(Optional) Displays backup information for this entry. |
detail |
(Optional) Displays link-state packet (LSP) details. |
Defaults
No instance ID specified displays the IP reachability information for all the IS-IS instances.
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The longer-prefixes keyword was added. |
Release 3.3.0 |
The multicast-intact keyword was added. |
Release 3.4.0 |
The safi-all and multicast keywords were added. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
The topology keyword was added for multicast routing tables on the Cisco XR 12000 Series Router. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following is sample output from the show isis route command:
RP/0/RP0/CPU0:router# show isis route
IS-IS isp IPv4 Unicast routes
Codes: L1 - level 1, L2 - level 2, ia - interarea (leaked into level 1)
df - level 1 default (closest attached router), su - summary null
C - connected, S - static, R - RIP, B - BGP, O - OSPF
i - IS-IS (redistributed from another instance)
Maximum parallel path count: 8
L2 10.76.240.6/32 [4/115]
via 10.76.245.252, SRP0/1/0/2, isp2
via 10.76.246.252, SRP0/1/0/0, isp2
is directly connected, Loopback0
L2 10.76.240.9/32 [256/115]
via 10.76.249.2, POS0/3/0/0, isp3
L2 10.76.240.10/32 [296/115]
via 10.76.249.2, POS0/3/0/0, isp3
is directly connected, SRP0/1/0/2
is directly connected, SRP0/1/0/0
is directly connected, POS0/3/0/0
L2 10.101.10.0/24 [296/115]
via 10.76.249.2, POS0/3/0/0, isp3
Table 21 describes the significant fields shown in the display.
Table 21 show isis route ipv4 unicast Field Descriptions
|
|
C172.18.0.0/24 |
Connected route for POS interface 0/5/0/0. |
C 172.19.1.0/24 |
Connected route for POS interface 0/4/0/1. |
L1 172.35.0.0/24 [10] |
Level 1 route to network 172.35.0.0/24. |
C 172.18.0/24 |
Connected route for loopback interface 0. |
show isis spf-log
To display how often and why the router has run a full shortest path first (SPF) calculation, use the show isis spf-log command in EXEC mode.
show isis [instance instance-id] [[ipv4 | ipv6 | afi-all] [unicast | multicast [topology {all | topo-name}] | safi-all]] spf-log [level {1 | 2}] [ispf | fspf | prc | nhc] [detail | verbose] [last number | first number]
Syntax Description
instance instance-id |
(Optional) Displays the IS-IS SPF log for the specified IS-IS instance only. |
ipv4 |
(Optional) Specifies IP Version 4 address prefixes. |
ipv6 |
(Optional) Specifies IP Version 6 address prefixes. |
afi-all |
(Optional) Specifies all address prefixes. |
unicast |
(Optional) Specifies unicast address prefixes. |
multicast |
(Optional) Specifies multicast address prefixes. |
topology all | topo-name |
(Optional) Specifies topology table information for all topologies or for the specified topology table (top-name). |
safi-all |
(Optional) Specifies all secondary address prefixes. |
level {1 | 2} |
(Optional) Displays the IS-IS SPF log for Level 1 or Level 2 independently. |
ispf |
(Optional) Specifies incremental SPF entries only. |
fspf |
(Optional) Specifies full SPF entries only. |
prc |
(Optional) Specifies partial route calculations only. |
nhc |
(Optional) Specifies next hop route calculations only. |
detail |
(Optional) Specifies detailed output. Includes a breakdown of the time taken to perform the calculation and changes resulting from the calculation. |
verbose |
(Optional) Specifies verbose output. |
last number |
(Optional) Specifies that the output is restricted to the last number of entries. Range is 1 to 210. |
first number |
(Optional) Specifies that the output is restricted to the first number of entries. Range is 1 to 210. |
Defaults
No instance ID specified displays IS-IS adjacencies for all the IS-IS instances.
Both Level 1 and Level 2 are configured if no level is specified.
Displays all types of route calculation (not just fspf, ispf and prc).
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
The ispf, fspf, prc, detail, internal, last number and first number keywords and arguments were added. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The internal keyword was removed. |
Release 3.3.0 |
The nhc and verbose keywords were added. |
Release 3.4.0 |
The safi-all and multicast keywords were added. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
The topology keyword was added for multicast spf-log on the Cisco XR 12000 Series Router. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following is sample output from the show isis spf-log command:
RP/0/RP0/CPU0:router# show isis spf-log
IS-IS 1 Level 1 IPv4 Unicast Route Calculation Log
Timestamp Type (ms) Nodes Count First Trigger LSP Triggers
----------- ---- ---- ----- ----- ----- ------- --- --------
--- Thurs Aug 19 2004 ---
12:00:50.787 FSPF 1 1 3 ensoft-grs7.00-00 LSPHEADER TLVCODE
12:00:52.846 FSPF 1 1 1 ensoft-grs7.00-00 LSPHEADER
12:00:56.049 FSPF 1 1 1 ensoft-grs7.00-00 TLVCODE
12:01:02.620 FSPF 1 1 2 ensoft-grs7.00-00 NEWADJ LINKTLV
IS-IS 1 Level 1 IPv4 Unicast Route Calculation Log
Timestamp Type (ms) Nodes Count First Trigger LSP Triggers
----------- ---- ---- ----- ----- ----- ------- --- --------
12:00:50.790 FSPF 0 1 4 ensoft-grs7.00-00 LSPHEADER TLVCODE
12:00:54.043 FSPF 1 1 2 ensoft-grs7.00-00 NEWADJ LSPHEADER
12:00:55.922 FSPF 1 2 1 ensoft-grs7.00-00 NEWLSPO
12:00:56.724 FSPF 1 13 1 ensoft-grs7.00-00 NEWLSPO
Table 22 describes the significant fields shown in the output.
Table 22 show isis spf-log ipv4 unicast Field Descriptions
|
|
Level |
IS-IS level of the router. |
Timestamp |
Time when the SPF calculation started. |
Duration |
Number of milliseconds taken to complete this SPF run. Elapsed time is wall clock time, not CPU time. |
Nodes |
Number of routers and pseudonodes (LANs) that make up the topology calculated in this SPF run. |
Trig Count |
Number of events that triggered this SPF run. When there is a topology change, often multiple link-state packets (LSPs) are received in a short time. Depending on the configuration of the spf-interval command, a router may wait for a fixed period of time before running a router calculation. This count denotes the number of triggering events that occurred while the router was waiting to run the calculation. For a full description of the triggering events, see Table 23. |
First Trigger LSP |
LSP ID stored by the router whenever a full SPF calculation is triggered by the arrival of a new LSP. The LSP ID can suggest the source of routing instability in an area. If multiple LSPs are causing an SPF run, only the LSP ID of the first received LSP is remembered. |
Triggers |
List of all reasons that triggered a full SPF calculation. For a list of possible triggers, see Table 23. |
Table 23 lists triggers of a full SPF calculation.
Table 23 List of Triggers
|
|
PERIODIC |
Runs a full SPF calculation very 15 minutes. |
NEWLEVEL |
Configured new level (using is-type) on this router. |
RTCLEARED |
Cleared IS-IS topology on the router. |
MAXPATHCHANGE |
Changed IP maximum parallel path. |
NEWMETRIC |
Changed link metric. |
ATTACHFLAG |
Changed Level 2 Attach bit. |
ADMINDIST |
Configured another administrative distance for the IS-IS instance on this router. |
NEWADJ |
Created a new adjacency to another router. |
DELADJ |
Deleted adjacency. |
BACKUP |
Installed backup route. |
SEEDISPF |
Seed incremental SPF. |
NEXTHOP |
Changed IP next-hop address. |
NEWLSP0 |
New LSP 0 appeared in the topology. |
LSPEXPIRED |
Some LSP in the link-state database (LSDB) has expired. |
LSPHEADER |
Changed important LSP header fields. |
TLVCODE |
Type, length, and value (TLV) objects code mismatch, indicating that different TLV objects are included in the newest version of an LSP. |
LINKTV |
Changed Link TLV content. |
PREFIXTLV |
Changed Prefix TLV content. |
AREAADDRTLV |
Changed Area address TLV content. |
IP ADDRTLV |
Changed IP address TLV content. |
TUNNEL |
Changed RRR tunnel. |
The following is sample output from the show isis spf-log command with the first keyword specified:
RP/0/RP0/CPU0:router# show isis spf-log first 2
IISIS isp Level 1 IPv4 Unicast Route Calculation Log
Timestamp Type (ms) Nodes Count First Trigger LSP Triggers
19:25:35.140 FSPF 1 1 1 12a5.00-00 NEWLSP0
19:25:35.646 FSPF 1 1 1 NEWADJ
IISIS isp Level 2 IPv4 Unicast Route Calculation Log
Timestamp Type (ms) Nodes Count First Trigger LSP Triggers
19:25:35.139 FSPF 1 1 1 12a5.00-00 NEWLSP0
19:25:35.347 FSPF 1 1 2 12a5.00-00 NEWSADJ TLVCODE
Table 24 describes the significant fields shown in the output.
Table 24 show isis spf-log first Field Descriptions
|
|
Level |
IS-IS level of the router. |
Timestamp |
Time at which the SPF calculation started. |
Type |
Type of route calculation. The possible types are incremental SPF (iSPF), full SPF (FSPF), or partial route calculation (PRC). |
Time (ms) |
Number of milliseconds taken to complete this SPF run. Elapsed time is wall clock time, not CPU time. |
Nodes |
Number of routers and pseudonodes (LANs) that make up the topology calculated in this SPF run. |
Trig Count |
Number of events that triggered this SPF run. When there is a topology change, often multiple link-state packets (LSPs) are received in a short time. Depending on the configuration of the spf-interval command, a router may wait for a fixed period of time before running a router calculation. This count denotes the number of triggering events that occurred while the router was waiting to run the calculation. For a full description of the triggering events, see Table 23. |
First Trigger LSP |
LSP ID stored by the router whenever a full SPF calculation is triggered by the arrival of a new LSP. The LSP ID can suggest the source of routing instability in an area. If multiple LSPs are causing an SPF run, only the LSP ID of the first received LSP is remembered. |
Triggers |
List of all reasons that triggered a full SPF calculation. For a list of possible triggers, see Table 23. |
The following is sample output from the show isis spf-log command with the detail keyword specified:
RP/0/RP0/CPU0:router# show isis spf-log detail
IISIS isp Level 1 IPv4 Unicast Route Calculation Log
Timestamp Type (ms) Nodes Count First Trigger LSP Triggers
19:25:35.140 FSPF 1 1 1 12a5.00-00 NEWLSP0
Delay: 51ms (since first trigger)
Next Wait Interval: 200ms
Table 25 describes the significant fields shown in the output.
Table 25 show isis spf-log detail Field Descriptions
|
|
Level |
IS-IS level of the router. |
Timestamp |
Time at which the SPF calculation started. |
Type |
Type of route calculation. The possible types are incremental SPF (iSPF), full SPF (FSPF), or partial route calculation (PRC). |
Time (ms) |
Number of milliseconds taken to complete this SPF run. Elapsed time is wall clock time, not CPU time. |
Nodes |
Number of routers and pseudonodes (LANs) that make up the topology calculated in this SPF run. |
Trig Count |
Number of events that triggered this SPF run. When there is a topology change, often multiple link-state packets (LSPs) are received in a short time. Depending on the configuration of the spf-interval command, a router may wait for a fixed period of time before running a router calculation. This count denotes the number of triggering events that occurred while the router was waiting to run the calculation. For a full description of the triggering events, see Table 23. |
First Trigger LSP |
LSP ID stored by the router whenever a full SPF calculation is triggered by the arrival of a new LSP. The LSP ID can suggest the source of routing instability in an area. If multiple LSPs are causing an SPF run, only the LSP ID of the first received LSP is remembered. |
Triggers |
List of all reasons that triggered a full SPF calculation. For a list of possible triggers, see Table 23. |
Delay |
Two different delays exist: 1. The delay between the time when the route calculation was first triggered and the time when it was run. 2. The delay between the end of the last route calculation and the start of this one. This is used to verify that the SPF-interval timers are working correctly, and is only reported for calculations after the first delay. |
CPU Time |
Two different CPU times exist: 1. CPU time (in milliseconds) taken to calculate the shortest path tree (SPT). 2. CPU time (in milliseconds) taken to perform the prefix updates. |
Real Time |
Two different real times exist: 1. Real time (in milliseconds) taken to calculate the shortest path tree (SPT). 2. Real time (in milliseconds) taken to perform the prefix updates. |
New LSP Arrivals |
Number of LSP arrivals since the start of this route calculation. |
Next Wait Interval |
Enforced delay until the next route calculation can be run, based on the spf-interval command configuration. |
Reach |
Number of reachable nodes or prefixes. |
Unreach |
Number of unreachable nodes or prefixes. |
Total |
Total number of nodes or prefixes at various priorities. |
Related Commands
|
|
spf-interval |
Sets IS-IS throttling of shortest path first (SPF) calculations. |
show isis statistics
To display Intermediate System-to-Intermediate System (IS-IS) traffic counters use the show isis statistics command in EXEC mode.
show isis [instance instance-id] statistics [interface-type interface-number]
Syntax Description
instance instance-id |
(Optional) Displays the IS-IS traffic statistics for the specified IS-IS instance only. •The instance-id argument is the instance identifier (alphanumeric) defined by the router isis command. |
interface-type |
(Optional) Interface type. For more information, use the question mark (?) online help function. |
interface-number |
(Optional) Either a physical interface instance or a virtual interface instance as follows: •Physical interface instance. Naming notation is rack/slot/module/port and a slash between values is required as part of the notation. –rack: Chassis number of the rack. –slot: Physical slot number of the modular services card or line card. –module: Module number. A physical layer interface module (PLIM) is always 0. –port: Physical port number of the interface. Note In references to a Management Ethernet interface located on a route processor card, the physical slot number is alphanumeric (RP0 or RP1) and the module is CPU0. Example: interface MgmtEth0/RP1/CPU0/0. •Virtual interface instance. Number range varies depending on interface type. For more information about the syntax for the router, use the question mark (?) online help function. |
Defaults
No instance ID specified displays IS-IS traffic statistics for all the IS-IS instances.
IS-IS traffic statistics are displayed for all interfaces.
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
The show isis statistics command displays IS-IS traffic counters for the specified interface or all traffic counters if no interface is specified.
Examples
The following is sample output from the show isis statistics command that shows all traffic counters:
RP/0/5/CPU0:router#show isis statistics
Fast PSNP cache (hits/tries): 164115/301454
Fast CSNP cache (hits/tries): 41828/43302
Fast CSNP cache updates: 2750
LSP checksum errors received: 0
Average transmit times and rate:
Hello: 0 s, 987947 ns, 4/s
CSNP: 0 s, 1452987 ns, 0/s
PSNP: 0 s, 1331690 ns, 0/s
LSP: 0 s, 1530018 ns, 1/s
Average process times and rate:
Hello: 0 s, 874584 ns, 41/s
CSNP: 0 s, 917925 ns, 29/s
PSNP: 0 s, 1405458 ns, 0/s
LSP: 0 s, 4352850 ns, 0/s
LSPs sourced (new/refresh): 3376/2754
Next Hop Calculations : 0
Partial Route Calculations : 0
IPFRR R-SPF calculations : 0
IPFRR Parallel calculations: 0
Next Hop Calculations : 13
Partial Route Calculations : 1
LSPs sourced (new/refresh): 4255/3332
Next Hop Calculations : 8
Partial Route Calculations : 0
IPFRR R-SPF calculations : 0
IPFRR Parallel calculations: 0
Next Hop Calculations : 82
Partial Route Calculations : 1
Interface GigabitEthernet0/1/0/1.1:
Level-1 Hellos (sent/rcvd): 22398/25633
Level-1 DR Elections : 66
Level-1 LSPs (sent/rcvd) : 246/7077
Level-1 CSNPs (sent/rcvd) : 0/33269
Level-1 PSNPs (sent/rcvd) : 22/0
Level-1 LSP Flooding Duplicates : 25129
Level-2 Hellos (sent/rcvd): 22393/67043
Level-2 DR Elections : 55
Level-2 LSPs (sent/rcvd) : 265/437
Level-2 CSNPs (sent/rcvd) : 0/86750
Level-2 PSNPs (sent/rcvd) : 0/0
Level-2 LSP Flooding Duplicates : 78690
Table 26 describes the significant fields shown in the display.
Table 26 show isis statistics Field Descriptions
|
|
Fast PSNP cache (hits/tries): |
Number of successful lookups (hits) along with the number of lookup attempts (tries). To save time or processing power when receiving multiple copies of the same LSP, IS-IS attempts to look up incoming LSPs to see if they have been received recently. |
Fast CSNP cache (hits/tries): |
Number of successful lookups (hits) along with the number of lookup attempts (tries). To reduce CSNP construction time, IS-IS maintains a cache of CSNPs and attempts to look up CSNP in this cache before transmission on the interface. |
Fast CSNP cache updates: |
Number of times the CSNP cache has been updated since the last clearing of statistics. The cache is updated on LSP addition or removal from the database. |
LSP checksum errors received: |
Number of internal checksum errors received in LSPs. |
IIH (LSP/SNP) dropped: |
Number of hello, LSP, and SNP messages dropped. |
IIH (UPD) Max Queue size: |
Maximum number of queued packets. |
Average transmit times and rate: |
Average time taken to transmit the pdu type across all interfaces and the corresponding rate at which the pdu type is being transmitted. |
Average process times and rate: |
Average time taken to process an incoming pdu type across all interfaces and the corresponding rate at which the pdu type is being received. |
LSPs sourced (new/refresh): |
Number of LSPs this IS-IS instance has created or refreshed. More details on these LSPs can be found using the show isis lsp-log command. |
SPF calculations: |
Number of shortest path first (SPF) calculations. SPF calculations are performed only when the topology changes. They are not performed when external routes change. The interval at which SPF calculations are performed is configured using the spf-interval command. |
iSPF calculations: |
Number of incremental shortest path first (iSPF) calculations. iSPF calculations are performed only when ISPF has been configured in the isis address family configuration submode. |
Partial Route Calculations: |
Number of partial route calculations (PRCs). PRCs are processor intensive. Therefore, it may be useful to limit how often a PRC is done, especially on slower networking devices. Increasing the PRC interval reduces the processor load on the router, but potentially slows the rate of convergence. The interval at which PRC calculations are performed is configured using the spf-interval command. |
Level-(1/2) (LSPs/ CSNPs/PSNPs/Hellos) (sent/rcvd): |
Number of LSPs, Complete Sequence Number Packets (CSNPs), Partial Sequence Number Packets (PSNPs), and hello packets sent or received on this interface. |
PTP Hellos (sent/rcvd): |
Point-to-point (PTP) hellos sent and received. |
LSP Retransmissions: |
Total number of retransmissions on each IS-IS LSP on a point-to-point interface. The LSP retransmission interval can be configured using the retransmit-throttle-interval command. |
Level-(1.2) DR Elections: |
Total number of Designated Intermediate System elections that have taken place. These counts are maintained on an individual level basis. |
LSP Flooding Duplicates: |
Number of duplicate LSPs filtered from flooding to the neighbor. In case of parallel interfaces to the same neighbor, IS-IS optimizes the flooding by avoiding sending the same LSP copy on other interfaces. |
Related Commands
|
|
show isis spf-log |
Displays how often and why the router has run a full SPF calculation. |
spf-interval |
Sets IS-IS throttling of shortest path first (SPF) calculations. |
show isis topology
To display a list of connected Intermediate System-to-Intermediate System (IS-IS) routers in all areas, use the show isis topology command in EXEC mode.
show isis [instance instance-id] [[ipv4 | ipv6 | afi-all] [unicast | multicast [topology {all | topo-name}] | safi-all]] | summary | level {1 | 2}] [multicast-intact] [systemid system-id] [detail]
Syntax Description
instance instance-id |
(Optional) Displays the IS-IS topology for the specified IS-IS instance only. •The instance-id argument is the instance identifier (alphanumeric) defined by the router isis command. |
ipv4 |
(Optional) Specifies IP Version 4 address prefixes. |
ipv6 |
(Optional) Specifies IP Version 6 address prefixes. |
afi-all |
(Optional) Specifies all address prefixes. |
unicast |
(Optional) Specifies unicast address prefixes. |
multicast |
(Optional) Specifies multicast address prefixes. |
topology topo-name |
(Optional) Specifies topology table information and name of the topology table. |
safi-all |
(Optional) Specifies all secondary address prefixes. |
summary |
(Optional) Displays a brief list of the IS-IS topology. |
level {1 | 2} |
(Optional) Displays the IS-IS link-state topology for Level 1 or Level 2 independently. |
multicast-intact |
(Optional) Displays multicast intact information on the IS-IS topology. |
systemid system-id |
(Optional) Displays the information for the specified router only. |
detail |
(Optional) Displays detailed information on the IS-IS topology. |
Defaults
No instance ID specified displays a list of connected routers in all areas for all the IS-IS instances.
Both Level 1 and Level 2 is configured if no level is specified.
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
The detail and multicast-intact keywords were added. |
Release 3.4.0 |
The safi-all and multicast keywords were added. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
The topology keyword was added to the multicast keyword on the Cisco XR 12000 Series Router. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the show isis topology command to verify the presence and connectivity among all routers in all areas.
Examples
The following is sample output from the show isis topology command:
RP/0/RP0/CPU0:router# show isis topology
IS-IS isp paths to (Level-1) routers
System Id Metric Next-Hop Interface SNPA
ensoft-5 10 ensoft-5 PO0/4/0/1 *PtoP*
ensoft-5 10 ensoft-5 Gi0/5/0/0 0003.6cff.0680
IS-IS isp paths to (Level-2) routers
System Id Metric Next-Hop Interface SNPA
ensoft-5 10 ensoft-5 PO0/4/0/1 *PtoP*
ensoft-5 10 ensoft-5 Gi0/5/0/0 0003.6cff.0680
Table 27 describes the significant fields shown in the display.
Table 27 show isis topology ipv4 unicast Field Descriptions
|
|
System ID |
Dynamic hostname of the system. The hostname is specified using the hostname command. If the dynamic hostname is not known or hostname dynamic disable command has been executed, the 6-octet system ID is used. |
Metric |
Metric assigned to the link and used to calculate the cost from each router using the links in the network to other destinations. Range is 1 to 16777214. Default is 1 to 63 for narrow metric and 1 to 16777214 for wide metric. 0 is set internally if no metric has been specified by the user. |
Next-Hop |
Address of the next hop. |
Interface |
Interface used to reach the neighbor. |
SNPA |
Data-link address (also known as the Subnetwork Point of Attachment [SNPA]) of the neighbor. |
The following is sample output from the show isis topology command with the summary keyword specified:
RP/0/RP0/CPU0:router# show isis topology summary
IS-IS 10 IS Topology Summary IPv4 Unicast
Reach UnReach Total Reach UnReach Total
------- ------- ------- ------- ------- -------
Router nodes: 1 1 2 1 1 2
Pseudo nodes: 0 0 0 0 0 0
Table 28 describes the significant fields shown in the display.
Table 28 show isis topology summary Field Descriptions
|
|
L1/L2 |
IS-IS level of the router. |
Reach |
Number of router nodes or pseudonodes that are reachable. |
UnReach |
Number of router nodes or pseudonodes that are unreachable. |
Total |
Total number of reachable and unreachable nodes. |
show protocols (IS-IS)
To group a number of protocol show commands according to the specified address family, use the show protocols command in EXEC mode.
show protocols [afi-all | ipv4 | ipv6] [all | protocol]
Syntax Description
afi-all |
(Optional) Specifies all address families. |
ipv4 |
(Optional) Specifies an IPv4 address family. |
ipv6 |
(Optional) Specifies an IPv6 address family. |
all |
(Optional) Specifies all protocols for a given address family. |
protocol |
(Optional) Specifies a routing protocol. For the IPv4 address family, the options are: •bgp •isis •ospf •rip •eigrp For the IPv6 address family, the options are •bgp •isis •ospfv3 |
Defaults
If no address family is specified, the default is IPv4.
Command Modes
EXEC
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. The afi-all keyword was added. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
If IPv6 is enabled on an IS-IS instance, the instance is displayed in the show protocols ipv6 command output. IPv4 IS-IS instances are displayed in the show protocols ipv4 command output.
When using the show protocols command with the ipv6 or ipv4 keyword, you get all routing instances in that particular address family—not only IS-IS instances.
Examples
The following example shows the output for the show protocols command using the ipv6 keyword:
RP/0/RP0/CPU0:router# show protocols ipv6
System Id: 0000.0000.12a8
Routing for area address(es):
Non-stop forwarding: Disabled
Most recent startup mode: Cold Restart
Topologies supported by IS-IS:
Metric style (generate/accept): Narrow/Narrow
Metric style (generate/accept): Narrow/Narrow
No protocols redistributed
Interfaces supported by IS-IS:
POS 0/6/0/0 is running actively (active in configuration)
Table 29 describes the significant fields shown in the display.
Table 29 show protocols ipv6 Field Descriptions
|
|
System ID |
Dynamic hostname of the system. The hostname is specified using the hostname command. If the dynamic hostname is not known or hostname dynamic disable command has been executed, the 6-octet system ID is used. |
IS Levels |
IS-IS level of the router. |
Manual area address(es) |
Area addresses configured manually on the originating router. |
Routing for area address(es) |
Area addresses for which this router provides the routing. |
Non-stop forwarding |
Status and name of NSF. |
Most recent startup mode |
Mode in which the most recent startup was performed. |
Topologies supported by IS-IS |
Address and subaddress family IS-IS are configured. |
Metric style |
Type, length, and value (TLV) objects accepted by IS-IS. To configure this value, see the metric-style narrow, metric-style transition, or metric-style wide command. |
ISPF status |
State of iSPF configuration for this IS-IS instance. Four states exist: •Disabled if iSPF has not been configured but is awaiting a full SPF to compile the topology for use by the iSPF algorithm. •Dormant if iSPF has been configured but is awaiting initial convergence before initializing. •Awake if iSPF has been configured but is awaiting a full SPF to compile the topology for use by the iSPF algorithm. •Active if IS-IS is ready to consider using the iSPF algorithm whenever a new route calculation needs to be run. |
Redistributing |
IS-IS is configured to redistribute IP static routes into Level 1 or Level 2. The redistribute command is used to configure redistribution. |
Distance |
Administrative distance. |
Interfaces supported by IS-IS |
Interfaces and their states currently supported by IS-IS. Both operational and configuration status are displayed. |
The following example shows how to disable the IPv6 address family, then no output is shown for IS-IS IPv6 instances from the show protocols ipv6 command:
RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# router isis uut
RP/0/RP0/CPU0:router(config-isis)# no address-family ipv6 unicast
RP/0/RP0/CPU0:router(config-isis)# commit
RP/0/RP0/CPU0:router# show protocols ipv6
Related Commands
|
|
metric-style narrow |
Configures the IS-IS software to generate and accept old-style type, length, and value (TLV) objects. |
metric-style transition |
Configures the IS-IS software to generate and accept both old-style and new-style type length, and value (TLV) objects. |
metric-style wide |
Configures the IS-IS software to generate and accept only new-style type, length, and value (TLV) objects. |
redistribute (IS-IS) |
Redistributes routes from one IS-IS instance into another instance. |
shutdown (IS-IS)
To disable the Intermediate System-to-Intermediate System (IS-IS) protocol on a particular interface, use the shutdown command in interface configuration mode. To re-enable the IS-IS protocol, use the no form of this command.
shutdown
no shutdown
Syntax Description
This command has no arguments or keywords.
Defaults
IS-IS protocol is enabled.
Command Modes
Interface configuration
Command History
|
|
Release 2.0 |
This command was introduced. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following example disables the IS-IS protocol on Packet-over-SONET/SDH (POS) interface 0/1/0/1:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface POS0/1/0/1
RP/0/RP0/CPU0:router(config-isis-if)# shutdown
single-topology
To configure the link topology for IP Version 4 (IPv4) when IP Version 6 (IPv6) is configured, use the single-topology command in address family configuration mode. To remove the single-topology command from the configuration file and restore the system to its default condition, use the no form of this command.
single-topology
no single-topology
Syntax Description
This command has no arguments or keywords.
Defaults
Performs in multitopology mode in which independent topologies for IPv4 and IPv6 are running in a single area or domain.
Command Modes
IPv6 address family configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the single-topology command to allow Intermediate System-to-Intermediate System (IS-IS) for IPv6 to be configured on interfaces along with an IPv4 network protocol. All interfaces must be configured with the identical set of network protocols, and all routers in the IS-IS area (for Level 1 routing) or the domain (for Level 2 routing) must support the identical set of network layer protocols on all interfaces.
When single-topology support for IPv6 is being used, only old-style type, length, and value (TLV) objects may be used and a single shortest path (SPF) individual level is used to compute IPv4 (if configured) and IPv6 routes. The use of a single SPF means that both IPv4 IS-IS and IPv6 IS-IS routing protocols must share a network topology.
To allow link information to be shared between IPv4 and IPv6, you must configure the single-topology command for an address family. In single-topology IPv6 mode, the configured metric is always the same for both IPv4 and IPv6.
Examples
The following example shows how to enable single-topology mode for IPv6:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# net 49.0000.0000.0001.00
RP/0/RP0/CPU0:router(config-isis)# address-family ipv6 unicast
RP/0/RP0/CPU0:router(config-isis-af)# single-topology
snmp-server traps isis
To enable the Simple Network Management Protocol (SNMP) server notifications (traps) available for IS-IS, use the snmp-server traps isis command in global configuration mode. To disable all available SNMP notifications, use the no form of this command.
snmp-server traps isis {all | traps set}
no snmp-server traps isis {all | traps set}
Syntax Description
all |
Specifies all IS-IS SNMP server traps. |
traps set |
Specify any set of trap names. |
Defaults
SNMP server traps notification is disabled.
Command Modes
Router configuration
Command History
|
|
Release 3.8.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following examples show how to enable all SNMP server traps available for isis:
RP/0/RP0/CPU0:router(config)# snmp-server traps isis ?
adjacency-change isisAdjacencyChange
all Enable all IS-IS traps
area-mismatch isisAreaMismatch
attempt-to-exceed-max-sequence isisAttemptToExceedMaxSequence
authentication-failure isisAuthenticationFailure
authentication-type-failure isisAuthenticationTypeFailure
corrupted-lsp-detected isisCorruptedLSPDetected
database-overload isisDatabaseOverload
id-len-mismatch isisIDLenMismatch
lsp-error-detected isisLSPErrorDetected
lsp-too-large-to-propagate isisLSPTooLargeToPropagate
manual-address-drops isisManualAddressDrops
max-area-addresses-mismatch isisMaxAreaAddressesMismatch
orig-lsp-buff-size-mismatch isisOrigLSPBuffSizeMismatch
own-lsp-purge isisOwnLSPPurge
protocols-supported-mismatch isisProtocolsSupportedMismatch
rejected-adjacency isisRejectedAdjacency
sequence-number-skip isisSequenceNumberSkip
version-skew isisVersionSkew
RP/0/RP0/CPU0:router(config)#snmp-server traps isis all
RP/0/RP0/CPU0:router(config)#snmp-server traps isis area-mismatch
spf-interval
To customize IS-IS throttling of shortest path first (SPF) calculations, use the spf-interval command in address family configuration mode. To restore default values, use the no form of this command.
spf-interval {[initial-wait initial | secondary-wait secondary | maximum-wait maximum] ...}[level {1 | 2}]
no spf-interval [[initial-wait initial | secondary-wait secondary | maximum-wait maximum] ...][level {1 | 2}]
Syntax Description
initial-wait initial |
Initial SPF calculation delay (in milliseconds) after a topology change. Range is 0 to 120000. |
secondary-wait secondary |
Hold time between the first and second SPF calculations (in milliseconds). Range is 0 to 120000. |
maximum-wait maximum |
Maximum interval (in milliseconds) between two consecutive SPF calculations. Range is 0 to 120000. |
level {1 | 2} |
(Optional) Enables the SPF interval configuration for Level 1 or Level 2 independently. |
Defaults
initial-wait initial: 50 milliseconds
secondary-wait secondary: 200 milliseconds
maximum-wait maximum: 5000 milliseconds
Command Modes
Address family configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
The initial-wait initial, secondary-wait secondary, and maximum-wait maximum keywords and arguments were added. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
SPF calculations are performed only when the topology changes. They are not performed when external routes change.
Use the spf-interval command to control how often the software can perform the SPF calculation. The SPF calculation is processor intensive. Therefore, it may be useful to limit how often this calculation is done, especially when the area is large and the topology changes often. Increasing the SPF interval reduces the processor load of the router, but potentially slows the rate of convergence.
Examples
The following example shows how to set the initial SPF calculation delay to 10 milliseconds and the maximum interval between two consecutive SPF calculations to 5000 milliseconds:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# spf-interval initial-wait 10 maximum-wait 5000
spf prefix-priority
To assign a priority to an ISIS prefix for customizing the RIB update sequence, use the spf prefix-priority command in address family configuration mode. To restore default values, use the no form of this command.
spf prefix-priority [level {1 | 2}] {critical | high | medium} {access-list-name | tag tag}
no spf prefix-priority [level {1 | 2}] {critical | high | medium} [access-list-name | tag tag]
Syntax Description
level {1 | 2} |
(Optional) Enables the assignment of a priority to Level 1 or Level 2 independently. |
critical |
Assigns a critical priority. |
high |
Assigns a high priority. |
medium |
Assigns a medium priority. |
access-list-name |
Name of an access list. |
tag tag |
Specifies a tag to indicate priority. The tag argument range is 1 to 4294967295. |
Defaults
By default, IPv4 prefixes with a length of 32 and IPv6 prefixes with a length of 128 are given medium priority. The remaining prefixes are given low priority.
Command Modes
Address family configuration
Command History
|
|
Release 3.3.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.4.0 |
The tag tag keyword and argument were added. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the spf prefix-priority command to change the sequence of prefix updates to the RIB after an SPF is run. ISIS installs prefixes in the RIB according to the following priority order:
Critical > High > Medium > Low
The spf prefix-priority command supports prefix lists for the first three priorities. The unmatched prefixes are updated with low priority.
If an spf prefix-priority is specified, the default behavior of prioritizing either length 32 or 128 prefixes for IPv4 or IPv6, respectively, as medium is disabled.
Examples
The following example shows how to set the prefix priorities:
RP/0/RP0/CPU0:router(config)# ipv4 prefix-list isis-critical-acl
RP/0/RP0/CPU0:router(config-ipv4_pfx)# 10 permit 0.0.0.0/0 eq 32
RP/0/RP0/CPU0:router(config)# ipv4 prefix-list isis-med-acl
RP/0/RP0/CPU0:router(config-ipv4_pfx)# 10 permit 0.0.0.0/0 eq 29
RP/0/RP0/CPU0:router(config)# ipv4 prefix-list isis-high-acl
RP/0/RP0/CPU0:router(config-ipv4_pfx)# 10 permit 0.0.0.0/0 eq 30
RP/0/RP0/CPU0:router(config)# router isis ring
RP/0/RP0/CPU0:router(config-isis)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-af)# spf prefix-priority critical isis-critical-acl
RP/0/RP0/CPU0:router(config-isis-af)# spf prefix-priority high isis-high-acl
RP/0/RP0/CPU0:router(config-isis-af)# spf prefix-priority medium isis-med-acl
summary-prefix (IS-IS)
To create aggregate addresses for the Intermediate System-to-Intermediate System (IS-IS) protocol, use the summary-prefix command in address family configuration mode. To restore the default behavior, use the no form of this command.
summary-prefix {address/prefix-length | ipv6-prefix/prefix-length} [level {1 | 2}]
no summary-prefix {address/prefix-length | ipv6-prefix/prefix-length} [level {1 | 2}]
Syntax Description
address |
Summary address designated for a range of IPv4 addresses. The address argument must be in four-part, dotted-decimal notation. |
/prefix-length |
Length of the IPv4 or IPv6 prefix. A decimal value that indicates how many of the high-order contiguous bits of the address compose the prefix (the network portion of the address). A slash must precede the decimal value. |
ipv6-prefix |
Summary prefix designated for a range of IPv6 prefixes. The ipv6-prefix argument must be in the form documented in RFC 2373, in which the address is specified in hexadecimal using 16-bit values between colons. |
level {1 | 2} |
(Optional) Redistributes routes into Level 1 or Level 2 and summarizes them with the configured address and mask value. |
Defaults
All redistributed routes are advertised individually.
Both Level 1 and Level 2 are configured if no level is specified.
Command Modes
Address family configuration
Command History
|
|
Release 2.0 |
This command was introduced on the Cisco CRS-1. |
Release 3.0 |
No modification. |
Release 3.2 |
This command was supported on the Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Multiple groups of addresses can be summarized for a given level. Routes learned from other routing protocols can also be summarized. The metric used to advertise the summary is the smallest metric of all the more-specific routes. Use the summary-prefix command to help reduce the size of the routing table.
This command also reduces the size of the link-state packets (LSPs) and thus the link-state database. It also helps ensure stability, because a summary advertisement depends on many more specific routes. If one more-specific route flaps, in most cases, this flap does not cause a flap of the summary advertisement.
The drawback of summary addresses is that other routes might have less information to calculate the most optimal routing table for all individual destinations.
Note When IS-IS advertises a summary prefix, it automatically inserts the summary prefix into the IP routing table but labels it as a "discard" route entry. Any packet that matches the entry is discarded to prevent routing loops. When IS-IS stops advertising the summary prefix, the routing table entry is removed.
Examples
The following example shows how to redistribute Open Shortest Path First (OSPF) routes into IS-IS. In the OSPF routing table, IPv6 routes exist for 3ffe:f000:0001:0000::/64, 3ffe:f000:0002:0000::/64, 3ffe:f000:0003:0000::/64, and so on. This example shows only 3ffe:f000::/24 advertised into IPv6 IS-IS Level 2.
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# address-family ipv6 unicast
RP/0/RP0/CPU0:router(config-isis-af)# redistribute ospfv3 2 level-2
RP/0/RP0/CPU0:router(config-isis-af)# summary-prefix 3ffe:f000::/24 level-2
suppressed
To allow an IS-IS interface to participate in forming adjacencies without advertising connected prefixes in the system link-state packets (LSPs), use the suppressed command in interface configuration mode. To enable advertising connected prefixes, use the no form of this command.
suppressed
no suppressed
Syntax Description
This command has no arguments or keywords.
Defaults
Interface is active.
Command Modes
Interface configuration
Command History
|
|
Release 3.2 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.3.0 |
No modification. |
Release 3.4.0 |
No modification. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Use the suppressed command to reduce the number of routes that IS-IS has to maintain, improving convergence times after an isolated failure. Improvement is noticeable if the command is used widely throughout the network. Other routers in the domain do not install routes to the affected connected prefixes.
Examples
The following example shows how to disable the advertisement of connected prefixes on Packet-over-SONET/SDH (POS) interface 0/1/0/1:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface POS0/1/0/1
RP/0/RP0/CPU0:router(config-isis-if)# suppressed
Related Commands
tag (IS-IS)
To associate and advertise a tag with the prefix of an IS-IS interface, use the tag command in interface address family configuration mode. To restore the default behavior, use the no form of this command.
tag tag
no tag [tag]
Syntax Description
tag |
Interface tag. Range is 1 to 4294967295. |
Defaults
Default is that no tag is associated and advertised.
Command Modes
Interface address family configuration
Command History
|
|
Release 3.4.0 |
This command was introduced on the Cisco CRS-1 and Cisco XR 12000 Series Router. |
Release 3.5.0 |
No modification. |
Release 3.6.0 |
No modification. |
Release 3.7.0 |
No modification. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following example shows how to associate and advertise an interface tag:
RP/0/RP0/CPU0:router(config)# router isis isp
RP/0/RP0/CPU0:router(config-isis)# interface POS 0/3/0/0
RP/0/RP0/CPU0:router(config-isis-if)# address-family ipv4 unicast
RP/0/RP0/CPU0:router(config-isis-if-af)# tag 234
Related Commands
|
|
spf prefix-priority |
Assigns a priority to an ISIS prefix for customizing the RIB update sequence. |
topology-id
To differentiate one topology in the domain from another while configuring a multicast routing table, use the topology-id command in Intermediate System-to-Intermediate System (IS-IS) routing configuration address family submode. To disable the topology use the no form of the command.
topology-id isis-multicast-topology-id-number
no topology-id isis-multicast-topology-id-number
Syntax Description
isis-multicast-topology-id-number |
Range is 6 to 4095. |
Command Default
No topology is associated with a routing table by default.
Command Modes
IS-IS address family configuration
Command History
|
|
Release 3.7.0 |
This command was first introduced on the Cisco XR 12000 Series Router. |
Release 3.8.0 |
No modification. |
Usage Guidelines
To use this command, your Cisco IOS XR software system administrator must assign you to a user group associated with a task group that includes the corresponding command task IDs. If you need assistance with your task group assignment, contact your system administrator. For detailed information about user groups and task IDs, see the Configuring AAA Services on Cisco IOS XR Software module of Cisco IOS XR System Security Configuration Guide.
Examples
The following example shows how to differentiate a topology from another in the multicast routing table in IS-IS routing:
RP/0/0/CPU0:router(config)# router isis isp
RP/0/0/CPU0:router(config-isis)# address-family ipv6 multicast topology green
RP/0/0/CPU0:router(config-isis-af)# topology-id 2666
Related Commands
|
|
address-family multicast topology (IS-IS) |
Used in conjunction with the topology-id command, enables a multicast topology globally when configuring Intermediate System-to-Intermediate System (IS-IS) routing. |