interface

peers

vni

sequence-interval through show platform software otv fp

sequence-interval

To assign sequential numbers to class-maps, use the sequence-interval command in policy-map configuration mode. To remove the numbers, use the no form of this command.

sequence-interval number

no sequence-interval number

Syntax Description

number

Specifies the sequential interval. The range is 1 to 65535.

Command Default

Class-maps are not assigned with sequential numbers.

Command Modes


Policy-map configuration (config-profile)

Command History

Release

Modification

15.1(2)T

This command was introduced.

Usage Guidelines

Use this command to assigns sequential numbers to the class-maps at specific interval.

Examples

The following example sets the interval as 100 to assign sequence numbers to class-maps:

Router(config)# policy-map type waas waas_global
Router(config-pmap)# sequence-interval 100

Related Commands

Command

Description

class

Associates a map class with a specified data-link connection identifier (DLCI).

passthrough

Allows traffic without optimization.

policy-map type waas

Defines a WAAS Express policy-map.

optimize

Applies WAAS optimization.

sequencing

To configure the direction in which sequencing is enabled for data packets in a Layer 2 pseudowire, use the sequencing command in pseudowire class configuration mode. To remove the sequencing configuration from the pseudowire class, use the no form of this command.

sequencing { transmit | receive | both | resync number }

no sequencing { transmit | receive | both | resync number }

Syntax Description

transmit

Updates the Sequence Number field in the headers of data packets sent over the pseudowire according to the data encapsulation method that is used.

receive

Keeps the value in the Sequence Number field in the headers of data packets received over the pseudowire. Out-of-order packets are dropped.

both

Enables both the transmit and receiveoptions.

resync

Enables the reset of packet sequencing after the disposition router receives a specified number of out-of-order packets.

number

The number of out-of-order packets that cause a reset of packet sequencing. The range is 5 to 65535.

Command Default

Sequencing is disabled.

Command Modes


Pseudowire class configuration

Command History

Release

Modification

12.0(23)S

This command was introduced for Layer 2 Tunnel Protocol Version 3 (L2TPv3).

12.3(2)T

This command was integrated into Cisco IOS Release 12.3(2)T.

12.0(29)S

This command was updated to support Any Transport over MPLS (AToM).

12.0(30)S

The resynckeyword was added.

12.2(25)S

This command was integrated into Cisco IOS Release 12.2(25)S.

12.2(27)SBC

L2TPv3 support for this command was integrated into Cisco IOS Release 12.2(27)SBC.

12.2(28)SB

AToM support for this command was integrated into Cisco IOS Release 12.2(28)SB.

Usage Guidelines

When you enable sequencing using any of the available options, the sending of sequence numbers is automatically enabled and the remote provider edge (PE) peer is requested to send sequence numbers. Out-of-order packets received on the pseudowire are dropped only if you use the sequencing receive or sequencing both command.

If you enable sequencing for Layer 2 pseudowires on the Cisco 7500 series routers and you issue the ip cef distributed command, all traffic on the pseudowires is switched through the line cards.

It is useful to specify the resync keyword for situations when the disposition router receives many out-of-order packets. It allows the router to recover from situations where too many out-of-order packets are dropped.

Examples

The following example shows how to enable sequencing in data packets in Layer 2 pseudowires that were created from the pseudowire class named “ether-pw” so that the Sequence Number field is updated in tunneled packet headers for data packets that are both sent and received over the pseudowire:

Router(config)
# pseudowire-class ether-pw
Router(config-pw)
# encapsulation mpls
Router(config-pw)
# sequencing both

The following example shows how to enable the disposition router to reset packet sequencing after it receives 1000 out-of-order packets:

Router(config)# pseudowire-class ether-pw
 
Router(config-pw)# encapsulation mpls
 
Router(config-pw)# sequencing both
 
Router(config-pw)# sequencing resync 1000

Related Commands

Command

Description

ip cef

Enables Cisco Express Forwarding on the Route Processor card.

pseudowire-class

Specifies the name of an L2TP pseudowire class and enters pseudowire class configuration mode.

services host-service peering

To configure the Secure Sockets Layer (SSL)-Express accelerator host peering service, use the services host-service peering command in WAAS SSL configuration mode.

services host-service peering

Syntax Description

This command has no arguments or keywords.

Command Default

Host peering service is enabled.

Command Modes

WAAS SSL configuration (config-waas-ssl)

Command History

Release

Modification

15.2(3)T

This command was introduced.

Usage Guidelines

SSL peering service configuration parameters control secure communications established by SSL-Express accelerator between WAAS Express devices while optimizing SSL connections.

Host peering service is enabled as soon as WAAS Express is enabled on a WAN interface. Host peering service is enabled with the default configurations for peer-ssl-version, peer-cipherlist, and peer-cert-verify enable commands. In the default state, the services host-service peering command does not display in the output of the show running-config all command. It displays in the show running-config all command output if any of the peer-ssl-version, peer-cipherlist, or peer-cert-verify enable command is modified.

To customize the peer-ssl-version, peer-cipherlist, or peer-cert-verify enable command, use the services host-service peering command in WAAS SSL configuration mode to enter SSL peering service configuration mode.

The services host-service peering command is used to enter SSL peering configuration mode. To exit SSL peering configuration mode, use the exit command in SSL peering configuration mode.

Examples

The following example shows how to customize a host peering service: 

Device(config)# parameter-map type waas waas_global
Device(config-profile)# accelerator ssl-express
Device(config-waas-ssl)# enable
Device(config-waas-ssl)# services host-service peering
Device(config-waas-ssl-peering)# peer-ssl-version ssl3

Related Commands

Command

Description

accelerator

Enters a specific WAAS Express accelerator configuration mode based on the accelerator being configured.

parameter-map type waas

Configures WAAS Express global parameters.

peer-cert-verify enable

Enables the verification of the peer certificate.

peer-cipherlist

Creates a cipher list to be used for WAAS-to-WAAS sessions.

peer-ssl-version

Configures the SSL version to be used for WAAS-to-WAAS sessions.

show running-config

Displays the contents of the current running configuration file or the configuration for a specific module, Layer 2 VLAN, class map, interface, map class, policy map, or VC class.

show waas accelerator

Displays information about WAAS Express accelerators.

show waas statistics accelerator

Displays statistical information about WAAS Express accelerators.

waas enable

Enables WAAS Express on a WAN interface.

waas-ssl-trustpoint

Associates a trustpoint with SSL-Express accelerator.

service pad

To enable all packet assembler/disassembler (PAD) commands and connections between PAD devices and access servers, use the service pad command in global configuration mode. To disable this service, use the no form of this command.

service pad [cmns] [from-xot] [to-xot]

no service pad [cmns] [from-xot] [to-xot]

Syntax Description

cmns

(Optional) Specifies sending and receiving PAD calls over CMNS.

from-xot

(Optional) Accepts XOT to PAD connections.

to-xot

(Optional) Allows outgoing PAD calls over XOT.

Command Default

All PAD commands and associated connections are enabled. PAD services over XOT or CMNS are not enabled.

Command Modes


Global configuration

Command History

Release

Modification

10.0

This command was introduced.

11.3

The cmns keyword was added.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

12.2(33)SB

This command was integrated into Cisco IOS Release 12.2(33)SB.

Usage Guidelines

The keywords from-xot and to-xot enable PAD calls to destinations that are not reachable over physical X.25 interfaces, but instead over TCP tunnels. This feature is known as PAD over XOT (X.25 over TCP).

Examples

If the service padcommandis disabled, the pad EXEC command and all PAD related configurations, such as X.29, are unrecognized, as shown in the following example:

Router(config)# no
 service pad
Router(config)# x29
 ?
% Unrecognized command
Router(config)# exit
 
Router# pad ?
% Unrecognized command

If the service padcommand is enabled, the pad EXEC command and access to an X.29 configuration are granted as shown in the following example:

Router# config terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)# service pad
Router(config)# x29 ?
access-list       Define an X.29 access list
inviteclear-time  Wait for response to X.29 Invite Clear message
profile           Create an X.3 profile
Router# pad ?
WORD   X121 address or name of a remote system

In the following example, PAD services over CMNS are enabled:

! Enable CMNS on a nonserial interface
interface ethernet0
 cmns enable
!
!Enable inbound and outbound PAD over CMNS service
service pad cmns
!
! Specify an X.25 route entry pointing to an interface’s CMNS destination MAC address
x25 route ^2193330 interface Ethernet0 mac 00e0.b0e3.0d62
Router# show x25 vc
SVC 1,  State: D1,  Interface: Ethernet0
     Started 00:00:08, last input 00:00:08, output 00:00:08
     Line: 0   con 0    Location: console Host: 2193330
      connected to 2193330 PAD <--> CMNS Ethernet0 00e0.b0e3.0d62
     Window size input: 2, output: 2
     Packet size input: 128, output: 128
     PS: 2  PR: 3  ACK: 3  Remote PR: 2  RCNT: 0  RNR: no
     P/D state timeouts: 0  timer (secs): 0
     data bytes 54/19 packets 2/3 Resets 0/0 RNRs 0/0 REJs 0/0 INTs 0/0

Related Commands

Command

Description

cmns enable

Enables the CMNS on a nonserial interface.

show x25 vc

Displays information about active SVCs and PVCs.

x29 access-list

Limits access to the access server from certain X.25 hosts.

x29 profile

Creates a PAD profile script for use by the translate command.

service pad from-xot

To permit incoming X.25 over TCP (XOT) calls to be accepted as a packet assembler/disassembler (PAD) session, use the service pad from-xotcommand in global configuration mode. To disable this service, use the no form of this command.

service pad from-xot

no service pad from-xot

Syntax Description

This command has no arguments or keywords.

Command Default

Incoming XOT connections are ignored.

Command Modes


Global configuration

Command History

Release

Modification

11.2

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

Usage Guidelines

If the service pad from-xotcommandis enabled, the calls received using the XOT service may be accepted for processing a PAD session.

Examples

The following example prevents incoming XOT calls from being accepted as a PAD session:

no service pad from-xot

Related Commands

Command

Description

x25 route

Creates an entry in the X.25 routing table (to be consulted for forwarding incoming calls and for placing outgoing PAD or protocol translation calls).

x29 access-list

Limits access to the access server from certain X.25 hosts.

x29 profile

Creates a PAD profile script for use by the translate command.

service pad to-xot

To permit outgoing PAD sessions to use routes to an XOT destination, use the service pad to-xotcommand in global configuration mode. To disable this service, use the no form of this command.

service pad to-xot

no service pad to-xot

Syntax Description

This command has no arguments or keywords.

Command Default

XOT routes pointing to XOT are not considered.

Command Modes


Global configuration

Command History

Release

Modification

11.2

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

Examples

If the service pad to-xotcommandis enabled, the configured routes to XOT destinations may be used when the router determines where to send a PAD Call, as shown in the following example:

service pad to-xot

Related Commands

Command

Description

x25 route

Creates an entry in the X.25 routing table (to be consulted for forwarding incoming calls and for placing outgoing PAD or protocol translation calls).

x29 access-list

Limits access to the access server from certain X.25 hosts.

x29 profile

Creates a PAD profile script for use by the translate command.

service translation

To enable upper layer user protocol encapsulation for Frame Relay-to-ATM Service Interworking (FRF.8) feature, which allows mapping between encapsulated ATM protocol data units (PDUs) and encapsulated Frame Relay PDUs, use the service translation command in FRF.8 connect configuration mode. To disable upper layer user protocol encapsulation, use the no form of this command.

service translation

no service translation

Syntax Description

This command has no arguments or keywords.

Command Default

The default state is service translation.

Command Modes


FRF.8 connect configuration

Command History

Release

Modification

12.1(2)T

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

Usage Guidelines

The no service translation command disables mapping between encapsulated ATM PDUs and encapsulated Frame Relay PDUs.

Examples

The following example shows an FRF.8 configuration with service translation disabled:

Router# show running-config
Building configuration...
Current configuration:
connect service-1 Serial1/0 16 ATM3/0 1/32 service-interworking
 no service translation
 efci-bit map-fecn

The following example shows how to configure service translation on the connection named service-1:

Router
(config)# 
connect service-1 serial1/0 16 ATM3/0 1/32 service-interworking
Router(config-frf8)# service translation

Related Commands

Command

Description

clp-bit

Sets the ATM CLP field in the ATM cell header.

connect (FRF.5)

Sets the Frame Relay DE bit field in the Frame Relay cell header.

de-bit map-clp

Sets the EFCI bit field in the ATM cell header.

set fr-fecn-becn

To enable forward explicit congestion notification (FECN) and backward explicit congestion notification (BECN) with Frame Relay over MPLS, use the set fr-fecn-becncommand in policy map class configuration mode. To disable the configuration notification, use the no form of this command.

set fr-fecn-becn percent

no set fr-fecn-becn percent

Syntax Description

percent

Specifies how much (percentage) of the total queue size should be used before marking the FECN and BECN bits. The valid range of percentages is 0 to 99. Setting the threshold to 0 indicates that all traffic is marked with FECN and BECN bits.

Command Default

Frame Relay does not perform FECN and BECN marking.

Command Modes


Policy map class configuration

Command History

Release

Modification

12.0(26)S

This command was introduced.

12.2(27)SXA

This command was integrated into Cisco IOS Release 12.2(27)SXA.

12.2(28)SB

This command was integrated into Cisco IOS Release 12.2(28)SB.

Usage Guidelines

This command works only with Frame Relay over MPLS.

If you configure FECN and BECN bit marking, you cannot configure bandwidth or priority.

Examples

The following example enables marking the FECN and BECN bits when 20 percent of the queue is used:

Router(config)# policy-map policy1 
Router(config-pmap)# class class1
Router(config-pmap-c)# shape 80000
Router(config-pmap-c)# set fr-fecn-becn 20

Related Commands

Command

Description

threshold ecn

Sets the FECN and BECN marking at the interface level.

shape fr-voice-adapt

To enable Frame Relay voice-adaptive traffic shaping, use the shape fr-voice-adaptcommand in policy-map class configuration mode. To disable Frame Relay voice-adaptive traffic shaping, use the noform of this command.

shape fr-voice-adapt [ deactivation seconds ]

no shape fr-voice-adapt

Syntax Description

deactivation seconds

(Optional) Number of seconds that must elapse after the last voice packet is transmitted before the sending rate is increased to the committed information rate (CIR). The range is from 1 to 10000.

Command Default

Frame Relay voice-adaptive traffic shaping is not enabled. Seconds: 30

Command Modes


Policy-map class configuration

Command History

Release

Modification

12.2(15)T

This command was introduced.

Usage Guidelines

Frame Relay voice-adaptive traffic shaping enables a router to reduce the permanent virtual circuit (PVC) sending rate to the minimum CIR (minCIR) whenever packets (usually voice) are detected in the low latency queueing priority queue or H.323 call setup signaling packets are present. When there are no packets in priority queue and signaling packets are not present for a configured period of time, the router increases the PVC sending rate from minCIR to CIR to maximize throughput.

The shape fr-voice-adaptcommand can be configured only in the class-default class. If you configure the shape fr-voice-adaptcommand in another class, the associated Frame Relay map class will be rejected when you attach it to the interface.

Frame Relay voice-adaptive traffic shaping can be used with other types of adaptive traffic shaping. For example, when both voice-adaptive traffic shaping and adaptive shaping based on interface congestion are configured, the sending rate will change to minCIR if there are packets in the priority queue or the interface queue size exceeds the configured threshold.


Note

Although the priority queue is generally used for voice traffic, Frame Relay voice-adaptive traffic shaping will respond to any packets (voice or data) in the priority queue.

In order to use Frame Relay voice-adaptive traffic shaping, you must have low latency queueing and traffic shaping configured using the Modular QoS CLI.

Examples

The following example shows the configuration of Frame Relay voice-adaptive traffic shaping and fragmentation. With this configuration, priority-queue packets or H.323 call setup signaling packets destined for PVC 100 will result in the reduction of the sending rate from CIR to minCIR and the activation of FRF.12 end-to-end fragmentation. If signaling packets and priority-queue packets are not detected for 50 seconds, the sending rate will increase to CIR and fragmentation will be turned off.

interface serial0
 encapsulation frame-relay
 frame-relay fragmentation voice-adaptive deactivation 50
 frame-relay fragment 80 end-to-end
 frame-relay interface-dlci 100
  class voice_adaptive_class
!
map-class frame-relay voice_adaptive_class
 frame-relay fair-queue  
 service-policy output shape
      
class-map match-all voice
 match access-group 102
class-map match-all data
 match access-group 101    
      
policy-map vats
 class voice
  priority 10
 class data
  bandwidth 10 
policy-map shape
 class class-default
  shape average 60000
  shape adaptive 30000
  shape fr-voice-adapt deactivation 50
  service-policy vats

Related Commands

Command

Description

frame-relay fragmentation voice-adaptive

Enables voice-adaptive Frame Relay fragmentation.

show policy-map

Displays the configuration of all classes for a specified service policy map or all classes for all existing policy maps.

show policy-map interface

Displays the packet statistics of all classes that are configured for all service policies either by interface or subinterface or by PVC.

show acircuit checkpoint

To display checkpointing information for each attachment circuit (AC), use the show acircuit checkpoint command in privileged EXEC mode.

show acircuit checkpoint

Syntax Description

This command has no arguments or keywords.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

12.2(25)S

This command was introduced.

12.2(28)SB

This command was integrated into Cisco IOS Release 12.2(28)SB.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

12.2(33)SRC

This command was integrated into Cisco IOS Release 12.2(33)SRC.

Usage Guidelines

This command is used for interface-based attachment circuits. For Frame Relay and ATM circuits, use the following commands to show redundancy information:

  • debug atm ha-error

  • debug atm ha-events

  • debug atm ha-state

  • debug atm l2transport

  • debug frame-relay redundancy

Examples

The following show acircuit checkpoint command displays information about the ACs that have been check-pointed. The output varies, depending on whether the command output is for the active or standby Route Processor (RP).

On the active RP, the command displays the following output: 

Router# show acircuit checkpoint
AC HA Checkpoint info:
Last Bulk Sync: 1 ACs
 AC    IW    XC    Id  VCId   Switch    Segment  St  Chkpt
----  ----  ----  ---  ----  --------  --------  --  -----
HDLC  LIKE  ATOM    3   100      1000      1000   0    N
VLAN  LIKE  ATOM    2  1002      2001      2001   3    Y

On the standby RP, the command displays the following output:: 

Router# show acircuit checkpoint
AC HA Checkpoint info:
 AC    IW    XC    Id  VCId   Switch    Segment  St  F-SLP
----  ----  ----  ---  ----  --------  --------  --  -----
HDLC  LIKE  ATOM    3   100         0         0   0   001
VLAN  LIKE  ATOM    2  1002      2001      2001   2   000

The table below describes the significant fields shown in the display.

Table 1 show acircuit checkpoint Field Descriptions

Field

Description

Last Bulk Sync

The number of ACs that were sent to the backup RP during the last bulk synchronization between the active and backup RPs.

AC

The type of attachment circuit.

IW

The type of interworking, either like-to-like (AToM) or any-to-any (Interworking).

XC

The type of cross-connect. Only AToM ACs are checkpointed.

ID

This field varies, depending on the type of attachment circuit. For Ethernet VLANs, the ID is the VLAN ID. For PPP and High-Level Data Link Control (HDLC), the ID is the AC circuit ID.

VCID

The configured virtual circuit ID.

Switch

An ID used to correlate the control plane and data plane contexts for this virtual circuit (VC). This is an internal value that is not for customer use.

Segment

An ID used to correlate the control plane and data plane contexts for this VC. This is an internal value that is not for customer use.

St

The state of the attachment circuit. This is an internal value that is not for customer use.

Chkpt

Whether the information about the AC was checkpointed.

F-SLP

Flags that provide more information about the state of the AC circuit. These values are not for customer use.

Related Commands

Command

Description

show mpls l2transport vc

Displays AToM status information.

show mpls l2transport vc checkpoint

Displays the status of the checkpointing process for both the active and standby RPs.

show ccm group

To display information about cluster control manager (CCM) groups on high availability (HA) Route Processor Stateful Switchover (RP-SSO) or Interchassis Stateful Switchover (IC-SSO) systems, use the show ccm group command in privileged EXEC mode.

show ccm group { all | id group-id }

Syntax Description

all

Displays information about all CCM groups (default, active, and inactive) configured on the router.

id

Displays the CCM group by group ID.

group-id

Valid existing CCM group ID.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

15.1(3)S

This command was introduced.

Usage Guidelines

Use the show ccm group command to display either all CCM redundancy groups with their group numbers or a specific CCM redundancy group, along with the number of CCM sessions in each group, the type of HA infrastructure, and the redundancy state of each group.

Examples

The following is sample output from the show ccm group all command: 

Device# show ccm group all
CCM Default Group(RP-SSO) Details
-----------------------------------
CCM Group ID              : 0
Infra Group ID            : Not Applicable
Infra Type                : Redundancy Facility (RF)
HA State                  : CCM HA Active
Redundancy State          : Collecting
Group Initialized/cleaned : Not Applicable
CCM Non-default Group(Inter-Box HA) Details
--------------------------------------------
 CCM Group 1 Details
------------------------
CCM Group ID              : 1
Infra Group ID            : 1
Infra Type                : Redundancy Group Facility (RGF)
HA State                  : CCM HA Active
Redundancy State          : Dynamic Sync

The following is sample output from the show ccm group id command: 

Device# show ccm group id 1
CCM Group 1 Details
----------------------------------------
CCM Group ID              : 1
Infra Group ID            : 1
Infra Type                : Redundancy Group Facility (RGF)
HA State                  : CCM HA Active
Redundancy State          : Dynamic Sync
Group Initialized/cleaned : FASLE

The table below describes the significant fields shown in the display. Any data not described in the table is either self-explanatory or used for Cisco internal debugging.

Table 2 show ccm group Field Descriptions

Field

Description

CCM Group ID

Group ID of the CCM group. The default group ID is 0.

Infra Group ID

The corresponding redundancy infrastructure ID for this CCM group. This ID also matches the corresponding APS group ID.

Infra Type

The HA infrastructure type (Redundancy Facility [RF] or RGF)

HA State

The current HA state of the CCM group (active, standby, or HA absent)

Redundancy State

The current redundancy state of sessions that belong to the CCM group.

Related Commands

Command

Description

show ccm sessions

Displays CCM session information about HA RP-SSO and IC-SSO systems.

show ccm sessions

To display information about cluster control manager (CCM) sessions on Route Processor Stateful Switchover (RP-SSO) or Interchassis Stateful Switchover (IC-SSO) systems, use the show ccm sessions command in privileged EXEC mode.

show ccm sessions [ id group-id ]

Syntax Description

id

Displays the CCM session by group ID.

group-id

Valid existing CCM group ID.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

12.2(31)SB2

This command was introduced.

12.2(33)SRC

This command was integrated into Cisco IOS Release 12.2(33)SRC.

15.1(3)S

This command was modified. The id group-id keyword-argument pair was added.

Usage Guidelines

Use the show ccm sessions command to display information about CCM sessions on active and standby processors, and also to display information about subscriber redundancy sessions configured using the subscriber redundancy command.

Examples

The following is sample output from the show ccm sessions command on a Cisco 10000 series router active processor: 

Device# show ccm sessions
Global CCM state:                                CCM HA Active - Dynamic Sync
Global ISSU state:                               Compatible, Clients Cap 0x0
	Number of sessions in state Down:                0
	Number of sessions in state Not Ready:           0
	Number of sessions in state Ready:               0
	Number of sessions in state Dyn Sync:            0
Timeout: Timer Type   Delay    Remaining Starts    CPU Limit CPU Last
		------------ -------- --------- --------- --------- --------
		Rate         00:00:01 	-         2         -         -       
		Dynamic CPU  00:00:10 	-         0         90        0

The following is sample output from the show ccm sessions command on a Cisco 10000 series router standby processor: 

Device# show ccm sessions
Global CCM state:                        CCM HA Standby - Collecting
Global ISSU state:                       Compatible, Clients Cap 0xFFE
                                         Current     Bulk Sent   Bulk Rcvd
                                         ----------- ----------- -----------
Number of sessions in state Down:        0           0           0          
Number of sessions in state Not Ready:   0           0           0          
Number of sessions in state Ready:       0           0           0          
Number of sessions in state Dyn Sync:    0           0           0          
Timeout: Timer Type   Delay    Remaining Starts      CPU Limit CPU Last
         ------------ -------- --------- ----------- --------- --------
         Rate         00:00:01 -         0           -         -       
         Dynamic CPU  00:00:10 -         0           90        0       
         Bulk Time Li 00:08:00 -         0           -         -       
         RF Notif Ext 00:00:20 -         0           -         -

The following is sample output from the show ccm sessions command on a Cisco 7600 series router active processor: 

Device# show ccm sessions
Global CCM state:                                CCM HA Active - Dynamic Sync
Global ISSU state:                               Compatible, Clients Cap 0xFFFE
										Current     Bulk Sent   Bulk Rcvd
                                         ----------- ----------- -----------
Number of sessions in state Down:        0           0           0          
Number of sessions in state Not Ready:   7424        0           0          
Number of sessions in state Ready:       0           0           0          
Number of sessions in state Dyn Sync:    20002       28001       0 
Timeout: Timer Type   Delay    Remaining Starts      CPU Limit CPU Last
         ------------ -------- --------- ----------- --------- --------
Rate         00:00:01 -         924         -         -       
         Dynamic CPU  00:00:10 -         0           90        2       
         Bulk Time Li 00:08:00 -         0           -         -       
         RF Notif Ext 00:00:20 -         18          -         -

The following is sample output from the show ccm sessions command on a Cisco 7600 series router standby processor: 

Device# show ccm sessions
Global CCM state:                        CCM HA Standby - Collecting
Global ISSU state:                       Compatible, Clients Cap 0xFFE
                                         Current     Bulk Sent   Bulk Rcvd
                                         ----------- ----------- -----------
Number of sessions in state Down:        0           0           0          
Number of sessions in state Not Ready:   8038        0           0          
Number of sessions in state Ready:       20002       0           28001      
Number of sessions in state Dyn Sync:    0           0           0 
Timeout: Timer Type   Delay    Remaining Starts      CPU Limit CPU Last
         ------------ -------- --------- ----------- --------- --------
Rate         00:00:01 -         0           -         -       
         Dynamic CPU  00:00:10 -         0           90        0       
         Bulk Time Li 00:08:00 -         1           -         -       
         RF Notif Ext 00:00:20 -         0           -         -

The following is sample output from the show ccm sessions id command on a Cisco 7600 series router: 

Device# show ccm sessions 
id
Global CCM state:                        CCM HA Active - Dynamic Sync
                                         Current     Bulk Sent   Bulk Rcvd
                                         ----------- ----------- -----------
Number of sessions in state Down:        0           0           31
Number of sessions in state Not Ready:   9           10          11
Number of sessions in state Ready:       0           0           56
Number of sessions in state Dyn Sync:    66          62          0
Timeout: Timer Type   Delay    Remaining Starts      CPU Limit CPU Last
         ------------ -------- --------- ----------- --------- --------
         Rate         00:00:01 -         0           -         -
         Dynamic CPU  00:00:10 -         0           90        0
         Bulk Time Li 00:08:00 -         0           -         -
         RF Notif Ext 00:00:01 -         0           -         -
         RGF Bulk Tim 00:05:00 -         1           -         -

The table below describes the significant fields shown in the display. Any data not described in the table is either self-explanatory or used for Cisco internal debugging.

Table 3 show ccm sessions Field Descriptions

Field

Description

Global CCM state

Displays the processor’s active or standby status and its CCM state. For example:

CCM HA Active - Dynamic Sync means that this is the active processor, standby is in STANDBY_HOT state, and CCM is ready to synchronize sessions.

CCM HA Active - Collecting means that this is the active processor and there is no standby processor. CCM can collect sessions but cannot synchronize them to a standby processor.

CCM HA Active - Bulk Sync means that this is the active processor and a standby processor is booting up. CCM is doing a bulk synchronization of sessions.

CCM HA Standby- Collecting means that this is the standby processor and is in STANDBY_HOT state. CCM is collecting sessions for synchronizing if a switchover happens.

Global ISSU state

Compatible, Clients Cap 0xFFFE0 indicates that CCM is compatible for in-service software upgrade (ISSU) clients, that is, ISSU-compatible Cisco IOS versions are running on both processors. It also means that CCM has the client capability for clients in the bitmask 0xFFFE.

Current

CCM sessions currently ready for synchronization.

Bulk Sent

CCM sessions sent during bulk synchronization.

Bulk Rcvd

CCM sessions received during bulk synchronization.

Number of sessions in state Down

Sessions in the down state.

Number of sessions in state Not Ready

Sessions in the not ready state.

Number of sessions in state Ready

Sessions in the ready state.

Number of sessions in state Dyn Sync

Sessions in the dynamic synchronization state.

Timeout

Displays statistics for the following timers:

Rate—Monitors the number of sessions to be synchronized per configured time period.

Dynamic CPU—Monitors the CPU limit, number of sessions, delay, and allowed calls configured for dynamic synchronization parameters.

Bulk Time Li—Monitors the time limit configured for bulk synchronization.

RF Notif Ext—Monitors redundancy facility (RF) active and standby state progressions and events.

Use the subscriber redundancy command to modify parameters that these timers monitor.

Delay

Timer delay (in hh:mm:ss) for bulk and dynamic synchronization of subscriber sessions.

Remaining

Indicates the remaining time in seconds before the timer expires.

Starts

Indicates the number of times the timer started.

CPU Limit

CPU usage percentage, a configurable value; default is 90 percent.

CPU Last

Indicates the last time the CPU limit timer was running.

Related Commands

Command

Description

show ccm clients

Displays CCM client information.

show ccm queues

Displays CCM queue information.

subscriber redundancy

Configures subscriber session redundancy policies.

show connect (FR-ATM)

To display statistics and other information about Frame-Relay-to-ATM Network Interworking (FRF.5) and Frame Relay-to-ATM Service Interworking (FRF.8) connections, use the show connectcommand in privileged EXEC mode.

show connect [ all | element | id ID | name | port port ]

Syntax Description

all

(Optional) Displays information about all Frame Relay-to-ATM connections.

element

(Optional) Displays information about the specified connection element.

id ID

(Optional) Displays information about the specified connection identifier.

name

(Optional) Displays information about the specified connection name.

port port

(Optional) Displays information about all connections on an interface.

Command Default

Default state is show connect all.

Command Modes


Privileged EXEC

Command History

Release

Modification

12.1(2)T

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

Examples

Examples

The following example displays information about all FRF.5 connections: 

C3640# show connect all
ID   Name               Segment 1            Segment 2           State
========================================================================
5    network-1         VC-Group network-1   ATM3/0 1/34          UP

The following example displays information about the specified FRF.5 connection identifier: 

Router# show connect id 5
FR/ATM Network Interworking Connection: network-1
  Status    - UP
  Segment 1 - VC-Group network-1
  Segment 2 - ATM3/0 VPI 1 VCI 34
  Interworking Parameters -
    de-bit map-clp
    clp-bit map-de

Examples

The following example displays information about the specified FRF.8 connection identifier: 

Router# show connect id 10
FR/ATM Service Interworking Connection: service-1
  Status    - UP
  Segment 1 - Serial1/0 DLCI 16
  Segment 2 - ATM3/0 VPI 1 VCI 32
Interworking Parameters -
    service translation
    efci-bit 0
    de-bit map-clp
    clp-bit map-de

The following example displays information about the FRF.8 connection on an interface: 

Router# show connect port atm3/0
ID   Name               Segment 1            Segment 2           State
========================================================================
10   service-1         Serial1/0 16         ATM3/0 1/32          UP

The table below describes the fields seen in these displays.

Table 4 show connect Field Descriptions

Display

Description

ID

Arbitrary connection identifier assigned by the operating system.

Name

Assigned connection name.

Segment 1 or 2

Frame Relay or ATM interworking segments.

State or Status

Status of the connection, UP, DOWN, or ADMIN DOWN.

Related Commands

Command

Description

connect (FRF.8)

Connects a Frame Relay DLCI to an ATM PVC.

show atm pvc

Displays all ATM PVCs, SVCs, and traffic information.

show frame-relay pvc

Displays statistics about Frame Relay interfaces.

show connection

To display the status of interworking connections, use the show connection command in privileged EXEC mode.

show connection [ all | element | id startid- [ endid ] | name name | port port ]

Syntax Description

all

(Optional) Displays information about all interworking connections.

element

(Optional) Displays information about the specified connection element.

id

(Optional) Displays information about the specified connection identifier.

startid

Starting connection ID number.

endid

(Optional) Ending connection ID number.

name name

(Optional) Displays information about the specified connection name.

port port

(Optional) Displays information about all connections on an interface. (In Cisco IOS Release 12.0S, only ATM, serial, and Fast Ethernet are shown.)

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

12.1(2)T

This command was introduced as show connect (FR-ATM).

12.0(27)S

This command was integrated into Cisco IOS Release 12.0(27)S and updated to show all ATM, serial, and Fast Ethernet interworking connections.

12.4(2)T

The command output was modified to add Segment 1 and Segment 2 fields for Segment state and channel ID.

12.0(30)S

This command was integrated into Cisco IOS Release 12.0(30)S.

12.2(25)S

This command was integrated into Cisco IOS Release 12.2(25)S.

12.2(28)SB

This command was integrated into Cisco IOS Release 12.2(28)SB.

12.4(8)

This command was integrated into Cisco IOS Release 12.4(8).

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.4(11)T

This command was integrated into Cisco IOS Release 12.4(11)T.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

12.2(33)SB

This command was updated to display High-Level Data Link Control (HDLC) local switching connections.

Cisco IOS XE Release 2.5

This command was integrated into Cisco IOS XE Release 2.5.

15.1(2)SNH

This command was implemented on the Cisco ASR 901 Series Aggregation Services Routers.

Examples

The following example shows the local interworking connections on a router: 

Device# show connection

ID   Name               Segment 1            Segment 2           State       
========================================================================
1    conn1          ATM 1/0/0 AAL5 0/100   ATM 2/0/0 AAL5 0/100   UP
2    conn2          ATM 2/0/0 AAL5 0/300   Serial0/1 16           UP
3    conn3          ATM 2/0/0 AAL5 0/400   FA 0/0.1 10            UP
4    conn4          ATM 1/0/0 CELL 0/500   ATM 2/0/0 CELL 0/500   UP
5    conn5          ATM 1/0/0 CELL 100     ATM 2/0/0 CELL 100     UP

The table below describes the significant fields shown in the display.

Table 5 show connection Field Descriptions

Field

Description

ID

Arbitrary connection identifier assigned by the operating system.

Name

Name of the connection.

Segment 1

Segment 2

Information about the interworking segments:

  • Interface name and number.

  • Segment state, interface name and number, and channel ID. Segment state will displays nothing if the segment state is UP, “-” if the segment state is DOWN, and “***Card Removed***” if the segment state is DETACHED.

  • Type of encapsulation (if any) assigned to the interface.

  • Permanent virtual circuit (PVC) assigned to the ATM interface, data-link connection identifier (DLCI) assigned to the serial interface, or VLAN ID assigned to the Ethernet interface.

State

Status of the connection, which is one of the following: INVALID, UP, ADMIN UP, ADMIN DOWN, OPER DOWN, COMING UP, NOT VERIFIED, ERR.

Related Commands

Command

Description

connect (L2VPN local switching)

Connects two different or like interfaces on a router.

show atm pvc

Displays the status of ATM PVCs and SVCs.

show frame-relay pvc

Displays the status of Frame Relay interfaces.

show ethernet service evc

To display information about Ethernet virtual connections (EVCs), use the showethernetserviceevccommand in privileged EXEC mode.

show ethernet service evc [ detail | id evc-id [detail] | interface type number [detail] ]

Syntax Description

interface detail

(Optional) Displays detailed information about service instances or the specified service instance ID or interface.

id

(Optional) Displays EVC information for the specified service.

evc-id

(Optional) String from 1 to 100 characters that identifies the EVC.

interface

(Optional) Displays service instance information for the specified interface.

type

(Optional) Type of interface.

number

(Optional) Number of the interface.

Command Modes

Privileged EXEC (#)

Command History

Release

Modification

12.2(25)SEG

This command was introduced.

12.2(33)SRB

This command was integrated into Cisco IOS Release 12.2(33)SRB.

Cisco IOS XE Release 3.8S

This command was integrated into Cisco IOS XE Release 3.8S.

15.1(2)SNG

This command was implemented on Cisco ASR 901 Series Aggregation Services Routers.

Usage Guidelines

This command is useful for system monitoring and troubleshooting.

Examples

Following is sample output from the show ethernet service evccommand: 

Device# show ethernet service evc

Identifier                     Type  Act-UNI-cnt Status
BLUE                           P-P       2       Active         
PINK                           MP-MP     2       PartiallyActive
PURPLE                         P-P       2       Active         
BROWN                          MP-MP     2       Active         
GREEN                          P-P       3       Active         
YELLOW                         MP-MP     2       PartiallyActive
BANANAS                        P-P       0       InActive       
TEST2                          P-P       0       NotDefined     
ORANGE                         P-P       2       Active         
TEAL                           P-P       0       InActive

The table below describes the significant fields in the output.

Table 6 show ethernet service evc Field Descriptions

Field

Description

Identifier

EVC identifier.

Type

Type of connection, for example point-to-point (P-P) or multipoint-to-multipoint (MP-MP).

Act-UNI-cnt

Number of active user network interfaces (UNIs).

Status

Availability status of the EVC.

Related Commands

Command

Description

show ethernet instance

Displays information about Ethernet customer service instances.

show ethernet interface

Displays interface-only information about Ethernet customer service instances.

show ethernet service instance

To display information about Ethernet service instances, use the show ethernet service instance command in privileged EXEC mode.

show ethernet service instance [ detail | id id { interface type number [ detail | mac { security [ address | last violation | statistics ] | static address } | load-balance | mac-tunnel [detail] ] } | platform | stats | interface type number [ detail | load-balance | platform | stats | summary ] | mac security [ address | last violation | statistics ] | platform | policy-map | stats | summary ]

Cisco ASR 901 Series Aggregation Services Router

show ethernet service instance [ detail | id id interface type number [ detail | mac security [ address | last violation | statistics ] | platform | stats ] | interface type number [ detail | platform | stats | summary ] | mac security [ address | last violation | statistics ] | platform | policy-map | stats | summary ]

Syntax Description

detail

(Optional) Displays detailed information about service instances, a specific service instance, or about a MAC tunnel service instance.

id

(Optional) Displays a specific service instance on an interface that does not map to a VLAN.

id

(Optional) Integer from 1 to 4294967295 that identifies a service instance on an interface that does not map to a VLAN.

interface

(Optional) Declares a specific interface selection for a specified service instance.

type

(Optional) Type of interface.

number

(Optional) Number of the interface.

mac

(Optional) Displays MAC address data.

security

(Optional) Displays the MAC security status of a specified service instance.

address

(Optional) Displays the secure addresses on the specified service instance.

last violation

(Optional) Displays the last violation recorded on the specified service instance.

statistics

(Optional) Displays MAC security statistics for the specified service instance.

static

(Optional) Displays MAC static address information.

address

(Optional) Displays MAC static addresses in a bridge domain.

load-balance

(Optional) Displays EtherChannel load-balancing information.

mac-tunnel

(Optional) Displays the MAC tunnel Ethernet service instance identifier.

platform

(Optional) Displays platform information for a specified service instance.

stats

(Optional) Displays statistics for a specified service instance.

summary

(Optional) Displays summary information about service instances.

policy-map

(Optional) Displays the policy map for service instances.

mac security

(Optional) Displays the MAC security status of the specified service instance for Cisco ASR 901 Series Aggregation Services Routers.

Command Modes

Privileged EXEC (#)

Command History

Release

Modification

12.2(25)SEG

This command was introduced.

12.2(33)SRB

This command was integrated into Cisco IOS Release 12.2(33)SRB.

12.2(33)SRD

This command was modified. The address, detail, lastviolation, macsecurity, platform, statistics, stats, and summary keywords were added.

12.2(33)SRE

This command was modified. The address, mac-tunnel, and static keywords were added.

15.0(1)S

This command was modified. The load-balance keyword was added.

15.1(2)S

This command was modified. The output was extended to include information about Layer 2 context service instances, service initiators associated with a Layer 2 context, and the control policy associated with a Layer 2 context service instance.

Cisco IOS XE Release 3.5S

This command was integrated into Cisco IOS XE Release 3.5S to provide support for the Cisco ASR 903 Router. This command was modified to provide support for Ethernet Flow Points (EFPs) on trunk ports (interfaces). The output includes information about trunk ports, if applicable.

15.1(2)SNG

This command was implemented on the Cisco ASR 901 Series Aggregation Services Router.

Usage Guidelines

This command is useful for system monitoring and troubleshooting.

Examples

The following is sample output from the show ethernet service instance command: 

Device# show ethernet service instance

Identifier  Type      Interface             State     CE-Vlans
4           static    GigabitEthernet3/2    Down

The table that follows describes the significant fields shown in the display.

Table 7 show ethernet service instance Field Descriptions

Field

Description

Identifier

Service instance identifier.

Type

Service instance type, as applicable, such as Static, L2Context, Dynamic, or Trunk.

Interface

Interface type and number with which the service instance is associated.

State

Service instance operational status such as Up, Down, or AdminDown.

CE-Vlans

Customer edge (CE) device VLAN ID.

Following is sample output from the show ethernet service instance detail command. The output shows details of different service instances configured on a given platform. 

Device# show ethernet service instance detail

Service Instance ID: 1
Service instance type: L2Context
Intiators: unclassified vlan
Control policy: ABC
Associated Interface: Ethernet0/0
Associated EVC: 
L2protocol drop
CE-Vlans:                                                                        
Encapsulation: dot1q 200-300 vlan protocol type 0x8100
Interface Dot1q Tunnel Ethertype: 0x8100
State: Up
EFP Statistics:
   Pkts In   Bytes In   Pkts Out  Bytes Out
         0          0          0          0

Service Instance ID: 2
Service instance type: Dynamic

Associated Interface: Ethernet0/0
Associated EVC: 
L2protocol drop
CE-Vlans: 10-20     
Encapsulation: dot1q 201 vlan protocol type 0x8100                                                             
Interface Dot1q Tunnel Ethertype: 0x8100
State: Up
EFP Statistics:
   Pkts In   Bytes In   Pkts Out  Bytes Out
         0          0          0          0

Following is sample output from the show ethernet service instance interface detail command. The output shows details of service instances configured on a specific interface. 

Device# show ethernet service instance interface ethernet 0/0 detail

Service Instance ID: 1
Service instance type: L2Context
Intiators: unclassified vlan
Control policy: ABC
Associated Interface: Ethernet0/0
Associated EVC: 
L2protocol drop
CE-Vlans:                                                                        
Encapsulation: dot1q 200-300 vlan protocol type 0x8100
Interface Dot1q Tunnel Ethertype: 0x8100
State: Up
EFP Statistics:
   Pkts In   Bytes In   Pkts Out  Bytes Out
         0          0          0          0

Service Instance ID: 2
Service instance type: Dynamic

Associated Interface: Ethernet0/0
Associated EVC: 
L2protocol drop
CE-Vlans: 10-20     
Encapsulation: dot1q 201 vlan protocol type 0x8100                                                             
Interface Dot1q Tunnel Ethertype: 0x8100
State: Up
EFP Statistics:
   Pkts In   Bytes In   Pkts Out  Bytes Out
         0          0          0          0

Service Instance ID: 3
Service instance type: static
Associated Interface: Ethernet0/0
Associated EVC: 
L2protocol drop
CE-Vlans: 10-20     
Encapsulation: dot1q 201 vlan protocol type 0x8100                                                             
Interface Dot1q Tunnel Ethertype: 0x8100
State: Up
EFP Statistics:
   Pkts In   Bytes In   Pkts Out  Bytes Out
         0          0          0          0

Following is sample output from the show ethernet service instance id interface detail command. The output shows details of a specific service instance configured on an interface. 

Device# show ethernet service instance id 1 interface ethernet 0/0 detail

Service Instance ID: 1
Service instance type: L2Context
Intiators: unclassified vlan
Control policy: ABC
Associated Interface: Ethernet0/0
Associated EVC: 
L2protocol drop
CE-Vlans:                                                                        
Encapsulation: dot1q 200-300 vlan protocol type 0x8100
Interface Dot1q Tunnel Ethertype: 0x8100
State: Up
EFP Statistics:
   Pkts In   Bytes In   Pkts Out  Bytes Out
         0          0          0          0

This is an example of output from the show ethernet service instance detail command on a Cisco ASR 901 Series Aggregation Services Router: 

Device# show ethernet service instance id 1 interface gigabitEthernet 0/1 detail

Service Instance ID: 1
Associated Interface: GigabitEthernet0/13
Associated EVC: EVC_P2P_10
L2protocol drop
CE-Vlans:
Encapsulation: dot1q 10 vlan protocol type 0x8100
Interface Dot1q Tunnel Ethertype: 0x8100
State: Up
EFP Statistics:
Pkts In Bytes In Pkts Out Bytes Out
214 15408 97150 6994800
EFP Microblocks:
****************
Microblock type: Bridge-domain
Bridge-domain: 10

This is an example of output from the show ethernet service instance stats command on a Cisco ASR 901 Series Aggregation Services Router: 

Device# show ethernet service instance id 1 interface gigabitEthernet 0/13 stats

Service Instance 1, Interface GigabitEthernet0/13
Pkts In Bytes In Pkts Out Bytes Out
214 15408 97150 6994800
Table 8 show ethernet service instance Field Descriptions

Field

Description

Service Instance ID

Service instance identifier.

Service instance type

Type of service instance.

Initiators

Service initiators associated with the service instance.

Control Policy

Control policy associated with the service instance.

Associated Interface

Interface on which the service instance is configured.

Associated EVC

Ethernet virtual circuit (EVC) associated with a device.

L2protocol drop

Number of Layer 2 protocol data units (PDUs) dropped.

CE-Vlans

VLANs associated with a device.

Encapsulation

Type of encapsulation used to enable session-level traffic classification.

Interface

Interface type and number with which the service instance is associated.

State

Up or Down.

EFP Statistics

Traffic on the service instance.

Related Commands

Command

Description

clear ethernet service instance

Clears Ethernet service instance attributes such as MAC addresses and statistics and purges Ethernet service instance errors.

show ethernet service interface

Displays interface-only information about Ethernet customer service instances.

show ethernet service interface

To display interface-only information about Ethernet customer service instances for all interfaces or for a specified interface, use the show ethernet service interface command in privileged EXEC mode.

show ethernet service interface [ type number ] [detail]

Syntax Description

type

(Optional) Type of interface.

number

(Optional) Number of the interface.

detail

(Optional) Displays detailed information about all interfaces or a specified service instance ID or interface.

Command Modes

Privileged EXEC (#)

Command History

Release

Modification

12.2(25)SEG

This command was introduced.

12.2(33)SRB

This command was integrated into Cisco IOS Release 12.2(33)SRB.

Cisco IOS XE Release 3.5S

This command was integrated into Cisco IOS XE Release 3.5S to provide support for the Cisco ASR 903 Device. This command was modified to provide support for Ethernet Flow Points (EFPs) on trunk ports (interfaces). The output includes information about trunk ports, if applicable.

Cisco IOS XE Release 3.6S

This command was modified. The output was modified to display the number of the bridge domains associated with the EFPs on an interface, if applicable.

15.1(2)SNG

This command was implemented on the Cisco ASR 901 Series Aggregation Services Router.

Usage Guidelines

Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain “Output” are displayed.

Examples

The following is an example of output from the show ethernet service interface command when the detail keyword is specified: 

Device# show ethernet service interface detail

Interface: FastEthernet0/1
ID:
CE-VLANS:
EVC Map Type: Bundling-Multiplexing
Interface: FastEthernet0/2
ID:
CE-VLANS:
EVC Map Type: Bundling-Multiplexing
Interface: FastEthernet0/3
ID:
CE-VLANS:
EVC Map Type: Bundling-Multiplexing
Bridge-Domains: 10,20,30
<output truncated>
Interface: GigabitEthernet0/1
ID: PE2-G101
CE-VLANS: 10,20,30
EVC Map Type: Bundling-Multiplexing
Associated EVCs:
EVC-ID CE-VLAN
WHITE 30
RED 20
BLUE 10
Associated Service Instances:
Service-Instance-ID CE-VLAN
10 10
20 20
30 30

The table below describes the significant fields in the output.

Table 9 show ethernet service interface Field Descriptions

Field

Description

Interface

Interface type and number.

Identifier

EVC identifier.

ID

EVC identifier.

CE-VLANS

VLANs associated with the customer edge (CE) device.

EVC Map Type

UNI service type; for example, Bundling, Multiplexing, All-to-one Bundling.

Bridge-Domains

Bridge domains associated with the EFPs on the interface.

Associated EVCs

EVCs associated with a device.

EVC-ID CE-VLAN

EVC identifier and associated VLAN.

Associated Service Instances

Service instances associated with a device.

Service-Instance-ID CE-VLAN

Service instance identifier and its associated CE VLAN.

Related Commands

Command

Description

service instance ethernet

Defines an Ethernet service instance and enters Ethernet service configuration mode.

show ethernet evc

Displays information about Ethernet customer service instances.

show ethernet interface

Displays interface-only information about Ethernet customer service instances.

show flow monitor type mace

To display the status and statistics for a flow monitor of type Measurement, Aggregation, and Correlation Engine (MACE), use the show flow monitor type macecommand in privileged EXEC mode.

show flow monitor type mace [name]

Syntax Description

name

(Optional) Name of a specific MACE flow monitor that is configured using the flow monitor type mace command.

Command Default

If no flow monitor name is specified, the command displays the status and statistics of all the configured flow monitors of type MACE.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

15.1(4)M

This command was introduced.

Usage Guidelines

Use the show flow monitor type command to display the status and statistics for a flow monitor of type MACE. If no flow monitor name is specified, the command displays the status and statistics of all the configured flow monitors of type MACE.


Note

You need to configure the flow monitor type mace command with a specific name to display the output for that flow monitor name using this command.

Examples

The following is sample output from the show flow monitor type mace command: 

Router# show flow monitor type mace mace_monitor_1
Flow Monitor type mace mace_monitor_1:
Description: User defined
Flow Record: mace_record
Flow Exporter: mace_exporter
No. of Inactive Users: 1
No. of Active Users: 0
Cache Timeout Update: 2 seconds

The table below describes the significant fields shown in the display.

Table 10 show flow record type mace Field Descriptions

Field

Description

Description

Displays the description provided for a flow monitor.

Flow Record

Displays the flow record that is included in the flow monitor.

Flow Exporter

Displays the flow exporter that is included in the flow monitor.

No. of Inactive Users

Displays the number of times that a flow monitor is inactive.

No. of Active Users

Displays the number of times that a flow monitor is active as an action under a policy when the policy is applied under an interface.

Cache Timeout Update

Displays the frequency with which the cache timeout is updated.

Related Commands

Command

Description

cache (Flexible NetFlow)

Configures a flow cache parameter for a Flexible NetFlow flow monitor.

flow monitor type mace

Configures a flow monitor of type MACE.

flow record

Configures the status and statistics for a Flexible Netflow flow record.

show flow record type

To display the configuration for a flow record, use the show flow record type command in privileged EXEC mode.

show flow record type { mace [ [name] flow-record-name ] | performance-monitor [name] [ default-rtp | default-tcp | record-name ] }

Syntax Description

mace

Displays Measurement, Aggregation, and Correlation Engine (MACE) metrics for the flow record.

name

(Optional) Displays the configuration for a specific MACE flow record if it is used with the mace keyword. Displays the configuration for a specific performance monitor flow record if it is used with the performance-monitor keyword.

flow-record-name

(Optional) Name of the user-defined MACE flow record that was previously configured.

performance-monitor

Displays configuration for the flow record of type performance monitor.

default-rtp

(Optional) Displays the Video Monitoring (VM) default Real-time Transport Protocol (RTP) record.

default-tcp

(Optional) Displays the VM default TCP record.

record-name

(Optional) Name of the user-defined performance monitor that was previously configured.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

15.1(4)M

This command was introduced.

Usage Guidelines

Use the show flow record type command to display the status and statistics for various flow record types. If you chose to use the name keyword in the command, you must use either the default-rtpor default-tcpkeywords, or use the record-nameargument to complete the command.


Note

You need to configure a flow record of type MACE using the flow record type mace command in order for the output of the show flow record type mace command to display information about the configured flow record.


Note

You need to configure a flow record of type performance monitor using the flow record type performance-monitor command in order for the output of the show flow record type performance-monitor command to display information about the configured flow record.

Examples

The following is sample output from the show flow record type mace command: 

Router# show flow record type mace mace1
flow record type mace mace1:
  Description:        User defined
  No. of users:       0
  Total field space:  164 bytes
  Fields:
    collect art all

The following is sample output from the show flow record type performance-monitor command: 

Router# show flow record type performance-monitor p1
flow record type performance-monitor p1:
  Description:        User defined
  No. of users:       0
  Total field space:  4 bytes
  Fields:
    collect application media bytes rate

The table below describes the significant fields shown in the above examples.

Table 11 show flow record type Field Descriptions

Field

Description

Description

Provides a description for this flow record.

No. of users

Indicates how many times a particular flow record has been used under a flow monitor.

Total field space

Displays the size of the record in bytes.

Fields

Displays the names of the fields that are configured.

Related Commands

Command

Description

flow record

Configures the status and statistics for an Flexible NetFlow flow record.

flow record type mace

Configures a flow record for MACE.

flow record type performance monitor

Configures a flow record for performance monitor.

show frame-relay end-to-end keepalive

To display statistics about Frame Relay end-to-end keepalive, use the show frame-relay end-to-end keepalive command in privileged EXEC mode.

show frame-relay end-to-end keepalive [ interface [dlci] | failures ]

Syntax Description

interface

(Optional) Interface to display.

dlci

(Optional) DLCI to display.

failures

(Optional) Displays the number of times keepalive has failed and the elapsed time since the last failure occurred.

Command Default

If no interface is specified, show all interfaces.

Command Modes


Privileged EXEC

Command History

Release

Modification

12.0(5)T

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.4T

This command was modified for Cisco IOS Release 12.4T.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

Usage Guidelines

Use this command to display the keepalive status of an interface.

Examples

The following examples show output from the show frame-relay end-to-end keepalive command:

Examples

Router# show frame-relay end-to-end keepalive interface s1
End-to-end Keepalive Statistics for Interface Serial1 (Frame Relay DTE)
DLCI = 100, DLCI USAGE = LOCAL, VC STATUS = STATIC (EEK UP)
 
SEND SIDE STATISTICS
Send Sequence Number: 86,       Receive Sequence Number: 87
Configured Event Window: 3,     Configured Error Threshold: 2
Total Observed Events: 90,      Total Observed Errors: 34
Monitored Events: 3,            Monitored Errors: 0
Successive Successes: 3,        End-to-end VC Status: UP
 
RECEIVE SIDE STATISTICS
Send Sequence Number: 88,       Receive Sequence Number: 87
Configured Event Window: 3,     Configured Error Threshold: 2
Total Observed Events: 90,      Total Observed Errors: 33
Monitored Events: 3,            Monitored Errors: 0
Successive Successes: 3,        End-to-end VC Status: UP

Examples

Router# show frame-relay end-to-end keepalive interface s1 failures
End-to-end Keepalive Statistics for Interface Serial1 (Frame Relay DTE)
DLCI = 100, DLCI USAGE = LOCAL, VC STATUS = STATIC (EEK UP)
SEND SIDE STATISTICS
Send Sequence Number: 86,       Receive Sequence Number: 87
Configured Event Window: 3,     Configured Error Threshold: 2
Total Observed Events: 90,      Total Observed Errors: 34
Monitored Events: 3,            Monitored Errors: 0
Successive Successes: 3,        End-to-end VC Status: UP
RECEIVE SIDE STATISTICS
Send Sequence Number: 88,       Receive Sequence Number: 87
Configured Event Window: 3,     Configured Error Threshold: 2
Total Observed Events: 90,      Total Observed Errors: 33
Monitored Events: 3,            Monitored Errors: 0
Successive Successes: 3,        End-to-end VC Status: UP
Failures Since Started: 1,      Last Failure: 00:01:31

The table below describes the fields shown in the display.

Table 12 show frame-relay end-to-end keepalive Field Descriptions

Field

Description

DLCI

The DLCI number that identifies the PVC.

DLCI USAGE

Lists SWITCHED when the router or access server is used as a switch, or LOCAL when the router or access server is used as a DTE device.

VC STATUS

Status of the PVC. The DCE device reports the status, and the DTE device receives the status. When you disable the Local Management Interface (LMI) mechanism on the interface (by using the no keepalive command), the PVC status is STATIC. Otherwise, the PVC status is exchanged using the LMI protocol:

  • STATIC--LMI is disabled on the interface.

  • ACTIVE-- The PVC is operational and can transmit packets.

  • INACTIVE--The PVC is configured, but down.

  • DELETED--The PVC is not present (DTE device only), which means that no status is received from the LMI protocol.

If the frame-relay end-to-end keepalive command is used, the end-to-end keepalive (EEK) status is reported in addition to the LMI status. For example:

  • ACTIVE (EEK UP) --The PVC is operational according to LMI and end-to-end keepalives.

  • ACTIVE (EEK DOWN)--The PVC is operational according to LMI, but end-to-end keepalive has failed.

Send Sequence Number

The current sequence number being sent in the keepalive packets.

Receive Sequence Number

The last sequence number received in the incoming keepalive packets.

Configured Event Window

The value configured by frame-relay end-to-end keepalive event-window command.

Configured Error Threshold

The value configured by frame-relay end-to-end keepalive error-threshold command.

Total Observed Events

The total number of successful events counted.

Total Observed Errors

The total number of error events counted.

Monitored Events

The number of events in current event window.

Monitored Errors

The number of errors in current event window.

Successive Successes

The number of successive success events in the current event window.

End-to-end VC Status

The status of the end-to-end keepalive protocol. The status is either UP or DOWN.

Failures Since Started

The number of times the end-to-end keepalive protocol has failed, causing the DLCI to go into the EEK DOWN state, since the protocol started.

Last Failure

The elapsed time since the last failure.

Related Commands

Command

Description

frame-relay end-to-end keepalive error-threshold

Modifies the keepalive error threshold value.

frame-relay end-to-end keepalive event-window

Modifies the keepalive event window value.

frame-relay end-to-end keepalive mode

Enables Frame Relay end-to-end keepalives.

frame-relay end-to-end keepalive success-events

Modifies the keepalive success events value.

frame-relay end-to-end keepalive timer

Modifies the keepalive timer.

map-class frame-relay

Specifies a map class to define QoS values for an SVC.

show frame-relay fragment

To display information about the Frame Relay fragmentation, use the show frame-relay fragment command in privileged EXEC mode.

show frame-relay fragment [ interface interface [dlci] ]

Syntax Description

interface

(Optional) Indicates a specific interface for which Frame Relay fragmentation information will be displayed.

interface

(Optional) Interface number containing the data-link connection identifier (DLCI) for which you wish to display fragmentation information.

dlci

(Optional) Specific DLCI for which you wish to display fragmentation information.

Command Modes


Privileged EXEC

Command History

Release

Modification

12.0(4)T

This command was introduced.

12.1(2)E

Support was added for Cisco 7500 series routers with Versatile Interface Processors.

12.1(5)T

Support was added for Cisco 7500 series routers with Versatile Interface Processors running 12.1(5)T.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

Cisco IOS XE Release

This command was integrated into Cisco IOS XE release.

Usage Guidelines

When no parameters are specified with this command, the output displays a summary of each DLCI configured for fragmentation. The information displayed includes the fragmentation type, the configured fragment size, and the number of fragments transmitted, received, and dropped.

When a specific interface and DLCI are specified, additional details are displayed.

Examples

The following is sample output for the show frame-relay fragment command without any parameters specified: 

Router# show frame-relay fragment
interface         dlci  frag-type    frag-size  in-frag    out-frag   dropped-frag
Serial0           108   VoFR-cisco   100        1261       1298       0         
Serial0           109   VoFR         100        0          243        0         
Serial0           110   end-to-end   100        0          0          0

The show frame-relay fragment command does not display any data in the in-frag and out-frag columns (displays 0) when high-priority data is flowing. The in-frag and out-frag columns are updated when low-priority data (only when packet size is greater than or equal to fragment size) is sent across the link.

The following is sample output for the show frame-relay fragment command when an interface and DLCI are specified: 

Router# show frame-relay fragment interface Serial1/0 16
  fragment-size 45                  fragment type end-to-end
  in fragmented pkts 0              out fragmented pkts 0
  in fragmented bytes 0             out fragmented bytes 0
  in un-fragmented pkts 0           out un-fragmented pkts 0
  in un-fragmented bytes 0          out un-fragmented bytes 0 
  in assembled pkts 0               out pre-fragmented pkts 0 
  in assembled bytes 0              out pre-fragmented bytes
  in dropped reassembling pkts 0    out dropped fragmenting pkts 0 
  in timeouts 0         
  in out-of-sequence fragments 0         
  in fragments with unexpected B bit set 0         
  out interleaved packets 0

The following table describes the fields shown in the display:

Table 13 show frame-relay fragment Field Descriptions

Field

Description

interface

Subinterface containing the DLCI for which the fragmentation information pertains.

dlci

Data-link connection identifier for which the displayed fragmentation information applies.

frag-type

Type of fragmentation configured on the designated DLCI. Supported types are end-to-end, VoFR, and VoFR-cisco.

frag-size

Configured fragment size in bytes.

in-frag

Total number of fragments received by the designated DLCI.

out-frag

Total number of fragments sent by the designated DLCI.

dropped-frag

Total number of fragments dropped by the designated DLCI.

in/out fragmented pkts

Total number of frames received/sent by this DLCI that have a fragmentation header.

in/out fragmented bytes

Total number of bytes, including those in the Frame Relay headers, that have been received/sent by this DLCI.

in/out un-fragmented pkts

Number of frames received/sent by this DLCI that do not require reassembly, and therefore do not contain the FRF.12 header. These counters can be incremented only when the end-to-end fragmentation type is set.

in/out un-fragmented bytes

Number of bytes received/sent by this DLCI that do not require reassembly, and therefore do not contain the FRF.12 header. These counters can be incremented only when the end-to-end fragmentation type is set.

in assembled pkts

Total number of fully reassembled frames received by this DLCI, including the frames received without a Frame Relay fragmentation header (in unfragmented packets). This counter corresponds to the frames viewed by the upper-layer protocols.

out pre-fragmented pkts

Total number of fully reassembled frames transmitted by this DLCI, including the frames transmitted without a Frame Relay fragmentation header (out un-fragmented pkts).

in assembled bytes

Number of bytes in the fully reassembled frames received by this DLCI, including the frames received without a Frame Relay fragmentation header (in un-fragmented bytes). This counter corresponds to the total number of bytes viewed by the upper-layer protocols.

out pre-fragmented bytes

Number of bytes in the fully reassembled frames transmitted by this DLCI, including the frames sent without a Frame Relay fragmentation header (out un-fragmented bytes). This counter corresponds to the total number of bytes viewed by the upper-layer protocols.

in dropped reassembling pkts

Number of fragments received by this DLCI that are dropped for reasons such as running out of memory, receiving segments out of sequence, receiving an unexpected frame with a B bit set, or timing out on a reassembling frame.

out dropped fragmenting pkts

Number of fragments that are dropped by this DLCI during transmission because of running out of memory.

in timeouts

Number of reassembly timeouts that have occurred on incoming frames to this DLCI. (A frame that does not fully reassemble within two minutes is dropped, and the timeout counter is incremented.)

in out-of-sequence fragments

Number of fragments received by this DLCI that have an unexpected sequence number.

in fragments with unexpected B bit set

Number of fragments received by this DLCI that have an unexpected B bit set. When this occurs, all fragments being reassembled are dropped and a new frame is begun with this fragment.

out interleaved packets

Number of packets leaving this DLCI that have been interleaved between segments.

Related Commands

Command

Description

frame-relay fragment

Enables fragmentation of Frame Relay frames for a Frame Relay map class.

show frame-relay pvc

Displays statistics about PVCs for Frame Relay interfaces.

show frame-relay vofr

Displays details about FRF.11 subchannels being used on Voice over Frame Relay DLCIs.

show interfaces serial

Displays information about a serial interface.

show traffic-shape queue

Displays information about the elements queued at a particular time at the VC level.

show frame-relay iphc

To display Frame Relay IP Header Compression Implementation Agreement (FRF.20) negotiation parameters for each PVC, use the show frame-relay iphc command in user EXEC or privileged EXEC mode.

show frame-relay iphc [ interface interface ] [dlci]

Syntax Description

interface

(Optional) Indicates a specific interface for which Frame Relay fragmentation information will be displayed.

interface

(Optional) Interface number containing the data link connection identifiers (DLCI(s)) for which you wish to display fragmentation information.

dlci

(Optional) Specific Data-Link Connection Identifier (DLCI) for which you wish to display fragmentation information. Valid values are from 16 to 1022.

Command Modes


User EXEC (>)
Privileged EXEC (#)

Command History

Release

Modification

12.4(15)T

This command was introduced.

12.1(2)E

This command was integrated into Cisco IOS Release 12.1(2)E.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command was integrated into Cisco IOS Release 12.2SX.

Examples

The following is sample output for the show frame-relay iphccommand without any parameters specified: 

Router# show frame-relay iphc
FRF.20 Statistics for Interface Serial2/0
DLCI 16 :
Parameters:        TCP space  16     non TCP space  16  
F_MAX period  256  F_MAX time 5      MAX header     168 
CP: State - req sent CP drops  0    
Reqs txed   2        Req rxed  0      Acks txed   0      Acks rxed  0

The table below describes the significant fields shown in the display.

Table 14 show frame-relay iphc Field Descriptions

Field

Description

DLCI

The DLCI number that identifies the PVC.

Parameters

Indicates FRF negotiation parameters configured for PVCs.

CP: State

Indicates the status of control protocol frames.

Related Commands

Command

Description

frame-relay fragment

Enables fragmentation of Frame Relay frames for a Frame Relay map class.

show frame-relay pvc

Displays statistics about PVCs for Frame Relay interfaces.

show frame-relay vofr

Displays details about FRF.11 subchannels being used on Voice over Frame Relay DLCIs.

show interfaces serial

Displays information about a serial interface.

show traffic-shape queue

Displays information about the elements queued at a particular time at the VC level.

show frame-relay ip tcp header-compression

To display Frame Relay Transmission Control Protocol (TCP)/IP header compression statistics, use the show frame-relay ip tcp header-compression command in user EXEC or privileged EXEC mode.

show frame-relay ip tcp header-compression [ interface type number ] [dlci]

Syntax Description

interface type number

(Optional) Specifies an interface for which information will be displayed. A space is optional between the type and number.

dlci

(Optional) Specifies a data-link connection identifier (DLCI) for which information will be displayed. Range is from 16 to 1022.

Command Modes


User EXEC
Privileged EXEC

Command History

Release

Modification

10.3

This command was introduced.

12.2(13)T

This command was integrated into Cisco IOS Release 12.2(13)T. The command was modified to support display of RTP header compression statistics for Frame Relay permanent virtual circuit (PVC) bundles.

12.2(27)SBC

This command was integrated into Cisco IOS Release 12.2(27)SBC, and the dlci argument was added.

12.2(28)SB

This command was integrated into Cisco IOS Release 12.2(28)SB.

12.4(9)T

The dlci argument was added.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

Examples

The following is sample output from the show frame-relay ip tcp header-compression command: 

Router# show frame-relay ip tcp header-compression
DLCI 200          Link/Destination info: ip 10.108.177.200
Interface Serial0:
Rcvd:     40 total, 36 compressed, 0 errors
          0 dropped, 0 buffer copies, 0 buffer failures
Sent:     0 total, 0 compressed
          0 bytes saved, 0 bytes sent
Connect:  16 rx slots, 16 tx slots, 0 long searches, 0 misses, 0% hit ratio
          Five minute miss rate 0 misses/sec, 0 max misses/sec

The following sample output from the show frame-relay ip tcp header-compression command shows statistics for a PVC bundle called “MP-3-static”: 

Router# show frame-relay ip tcp header-compression interface Serial1/4
 vc-bundle MP-3-static      Link/Destination info:ip 10.1.1.1
  Interface Serial1/4:
    Rcvd:   14 total, 13 compressed, 0 errors
             0 dropped, 0 buffer copies, 0 buffer failures
    Sent:   15 total, 14 compressed,
             474 bytes saved, 119 bytes sent
             4.98 efficiency improvement factor
    Connect:256 rx slots, 256 tx slots,
             1 long searches, 1 misses 0 collisions, 0 negative cache hits
             93% hit ratio, five minute miss rate 0 misses/sec, 0 max

In the following example, the show frame-relay ip tcp header-compression command displays information about DLCI 21: 

Router# show frame-relay ip tcp header-compression 21
DLCI 21         Link/Destination info: ip 10.1.2.1
  Interface POS2/0 DLCI 21 (compression on, VJ)
    Rcvd:    0 total, 0 compressed, 0 errors, 0 status msgs
             0 dropped, 0 buffer copies, 0 buffer failures
    Sent:    0 total, 0 compressed, 0 status msgs, 0 not predicted
             0 bytes saved, 0 bytes sent
    Connect: 256 rx slots, 256 tx slots, 
             0 misses, 0 collisions, 0 negative cache hits, 256 free contexts
DLCI 21         Link/Destination info: ip 10.1.4.1
  Interface Serial3/0 DLCI 21 (compression on, VJ)
    Rcvd:    0 total, 0 compressed, 0 errors, 0 status msgs
             0 dropped, 0 buffer copies, 0 buffer failures
    Sent:    0 total, 0 compressed, 0 status msgs, 0 not predicted
             0 bytes saved, 0 bytes sent
    Connect: 256 rx slots, 256 tx slots, 
             0 misses, 0 collisions, 0 negative cache hits, 256 free contexts

The following is sample output from the show frame-relay ip tcp header-compression command for a specific DLCI on a specific interface: 

Router# show frame-relay ip tcp header-compression pos2/0 21
DLCI 21         Link/Destination info: ip 10.1.2.1
  Interface POS2/0 DLCI 21 (compression on, VJ)
    Rcvd:    0 total, 0 compressed, 0 errors, 0 status msgs
             0 dropped, 0 buffer copies, 0 buffer failures
    Sent:    0 total, 0 compressed, 0 status msgs, 0 not predicted
             0 bytes saved, 0 bytes sent
    Connect: 256 rx slots, 256 tx slots, 
             0 misses, 0 collisions, 0 negative cache hits, 256 free contexts

The table below describes the fields shown in the display.

Table 15 show frame-relay ip tcp header-compression Field Descriptions

Field

Description

Rcvd:

Table of details concerning received packets.

total

Sum of compressed and uncompressed packets received.

compressed

Number of compressed packets received.

errors

Number of errors caused by errors in the header fields (version, total length, or IP checksum).

dropped

Number of packets discarded. Seen only after line errors.

buffer failures

Number of times that a new buffer was needed but was not obtained.

Sent:

Table of details concerning sent packets.

total

Sum of compressed and uncompressed packets sent.

compressed

Number of compressed packets sent.

bytes saved

Number of bytes reduced because of the compression.

bytes sent

Actual number of bytes transmitted.

Connect:

Table of details about the connections.

rx slots, tx slots

Number of states allowed over one TCP connection. A state is recognized by a source address, a destination address, and an IP header length.

long searches

Number of times that the connection ID in the incoming packet was not the same as the previous one that was processed.

misses

Number of times that a matching entry was not found within the connection table and a new entry had to be entered.

hit ratio

Percentage of times that a matching entry was found in the compression tables and the header was compressed.

Five minute miss rate

Miss rate computed over the most recent 5 minutes and the maximum per-second miss rate during that period.

show frame-relay lapf

To display information about the status of the internals of Frame Relay Layer 2 (LAPF) if switched virtual circuits (SVCs) are configured, use the show frame-relay lapf command in user EXEC or privileged EXEC mode.

show frame-relay lapf

Syntax Description

This command has no arguments or keywords.

Command Modes


User EXEC
Privileged EXEC

Command History

Release

Modification

11.2

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

Examples

The following is sample output from the show frame-relay lapfcommand. 

Router# show frame-relay lapf
Interface = Serial1 (up),  LAPF state = TEI_ASSIGNED (down)
SVC disabled, link down cause = LMI down,  #link-reset = 0
T200 = 1.5 sec.,  T203 = 30 sec.,  N200 = 3,  k = 7,  N201 = 260
I xmt = 0, I rcv = 0, I reXmt = 0, I queued = 0
I xmt dropped = 0,  I rcv dropped = 0,  Rcv pak dropped = 0
RR xmt = 0,  RR rcv = 0,  RNR xmt = 0,  RNR rcv = 0
REJ xmt = 0,  REJ rcv = 0,  FRMR xmt = 0,  FRMR rcv = 0
DM xmt = 0,  DM rcv = 0,  DISC xmt = 0,  DISC rcv = 0
SABME xmt = 0,  SABME rcv = 0,  UA xmt = 0,  UA rcv = 0
V(S) = 0,  V(A) = 0,  V(R) = 0,  N(S) = 0,  N(R) = 0
Xmt FRMR at Frame Reject

The table below describes significant fields in this output.

Table 16 show frame-relay lapf Field Descriptions

Field

Description

Interface

Identifies the interface and indicates the line status (up, down, administratively down).

LAPF state

A LAPF state of MULTIPLE FRAME ESTABLISHED or RIMER_RECOVERY indicates that Layer 2 is functional. Others, including TEI_ASSIGNED, AWAITING_ESTABLISHMENT, and AWAITING_RELEASE, indicate that Layer 2 is not functional.

SVC disabled

Indicates whether SVCs are enabled or disabled.

link down cause

Indicates the reason that the link is down. For example, N200 error, memory out, peer disconnect, LMI down, line down, and SVC disabled. Many other causes are described in the Q.922 specification.

#link-reset

Number of times the Layer 2 link has been reset.

T200, T203, N200, k, N201

Values of Layer 2 parameters.

I xmt, I rcv, I reXmt, I queued

Number of I frames sent, received, retransmitted, and queued for transmission, respectively.

I xmt dropped

Number of sent I frames that were dropped.

I rcv dropped

Number of I frames received over DLCI 0 that were dropped.

Rcv pak dropped

Number of received packets that were dropped.

RR xmt, RR rcv

Number of RR frames sent; number of RR frames received.

RNR xmt, RNR rcv

Number of RNR frames sent; number of RNR frames received.

REJ xmt, REJ rcv

Number of REJ frames sent; number of REJ frames received.

FRMR xmt, FRMR rcv

Number of FRMR frames sent; number of FRMR frames received.

DM xmt, DM rcv

Number of DM frames sent; number of DM frames received.

DISC xmt, DISC rcv

Number of DISC frames sent; number of DISC frames received.

SABME xmt, SABME rcv

Number of SABME frames sent; number of SABME frames received.

UA xmt, UA rcv

Number of UA frames sent; number of UA frames received.

V(S) 0, V(A) 0, V(R) 0, N(S) 0, N(R) 0

Layer 2 sequence numbers.

Xmt FRMR at Frame Reject

Indicates whether the FRMR frame is sent at Frame Reject.

show frame-relay lmi

To display statistics about the Local Management Interface (LMI), use the show frame-relay lmi command in user EXEC or privileged EXEC mode.

show frame-relay lmi [ type number ]

Syntax Description

type

(Optional) Interface type; it must be serial.

number

(Optional) Interface number.

Command Modes


User EXEC
Privileged EXEC

Command History

Release

Modification

10.0

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

12.0(33)S

Support for IPv6 was added. This command was implemented on the Cisco 12000 series routers.

Usage Guidelines

Enter the command without arguments to obtain statistics about all Frame Relay interfaces.

Examples

The following is sample output from the show frame-relay lmi command when the interface is a data terminal equipment (DTE) device: 

Router# show frame-relay lmi
LMI Statistics for interface Serial1 (Frame Relay DTE) LMI TYPE = ANSI
  Invalid Unnumbered info 0             Invalid Prot Disc 0
  Invalid dummy Call Ref 0              Invalid Msg Type 0
  Invalid Status Message 0              Invalid Lock Shift 0
  Invalid Information ID 0              Invalid Report IE Len 0
  Invalid Report Request 0              Invalid Keep IE Len 0
  Num Status Enq. Sent 9                Num Status msgs Rcvd 0
  Num Update Status Rcvd 0              Num Status Timeouts 9

The following is sample output from the show frame-relay lmi command when the interface is a Network-to-Network Interface (NNI): 

Router# show frame-relay lmi
LMI Statistics for interface Serial3 (Frame Relay NNI) LMI TYPE = CISCO
  Invalid Unnumbered info 0             Invalid Prot Disc 0
  Invalid dummy Call Ref 0              Invalid Msg Type 0
  Invalid Status Message 0              Invalid Lock Shift 0
  Invalid Information ID 0              Invalid Report IE Len 0
  Invalid Report Request 0              Invalid Keep IE Len 0
  Num Status Enq. Rcvd 11               Num Status msgs Sent 11
  Num Update Status Rcvd 0              Num St Enq. Timeouts 0
  Num Status Enq. Sent 10               Num Status msgs Rcvd 10
  Num Update Status Sent 0              Num Status Timeouts 0

The table below describes significant fields shown in the output.

Table 17 show frame-relay lmi Field Descriptions

Field

Description

LMI Statistics

Signalling or LMI specification: CISCO, ANSI, or ITU-T.

Invalid Unnumbered info

Number of received LMI messages with invalid unnumbered information field.

Invalid Prot Disc

Number of received LMI messages with invalid protocol discriminator.

Invalid dummy Call Ref

Number of received LMI messages with invalid dummy call references.

Invalid Msg Type

Number of received LMI messages with invalid message type.

Invalid Status Message

Number of received LMI messages with invalid status message.

Invalid Lock Shift

Number of received LMI messages with invalid lock shift type.

Invalid Information ID

Number of received LMI messages with invalid information identifier.

Invalid Report IE Len

Number of received LMI messages with invalid Report IE Length.

Invalid Report Request

Number of received LMI messages with invalid Report Request.

Invalid Keep IE Len

Number of received LMI messages with invalid Keep IE Length.

Num Status Enq. Sent

Number of LMI status inquiry messages sent.

Num Status Msgs Rcvd

Number of LMI status messages received.

Num Update Status Rcvd

Number of LMI asynchronous update status messages received.

Num Status Timeouts

Number of times the status message was not received within the keepalive time value.

Num Status Enq. Rcvd

Number of LMI status enquiry messages received.

Num Status Msgs Sent

Number of LMI status messages sent.

Num Status Enq. Timeouts

Number of times the status enquiry message was not received within the T392 DCE timer value.

Num Update Status Sent

Number of LMI asynchronous update status messages sent.

show frame-relay map

To display current Frame Relay map entries and information about connections, use the show frame-relay map command in privileged EXEC mode.

show frame-relay map [ interface type number ] [dlci]

Syntax Description

interface type number

(Optional) Specifies an interface for which mapping information will be displayed. A space is optional between the interface type and number.

dlci

(Optional) Specifies a data-link connection identifier (DLCI) for which mapping information will be displayed. Range: 16 to 1022.

Command Default

Static and dynamic Frame Relay map entries and information about connections for all DLCIs on all interfaces are displayed.

Command Modes


Privileged EXEC

Command History

Release

Modification

10.0

This command was introduced.

12.2(2)T

The display output for this command was modified to include the IPv6 address mappings of remote nodes to Frame Relay permanent virtual circuits (PVCs).

12.0(21)ST

This command was integrated into Cisco IOS Release 12.0(21)ST.

12.0(22)S

This command was integrated into Cisco IOS Release 12.0(22)S.

12.2(14)S

This command was integrated into Cisco IOS Release 12.2(14)S.

12.2(13)T

The display output for this command was modified to include information about Frame Relay PVC bundle maps.

12.2(28)SB

This command was integrated into Cisco IOS Release 12.2(28)SB, the interface keyword was added, and the dlci argument was added.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.4(9)T

The interface keyword was added, and the dlci argument was added.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

Cisco IOS XE Release 2.1

This command was introduced on Cisco ASR 1000 Series Routers.

12.0(33)S

This command was implemented on the Cisco 12000 series routers.

Examples

This section contains the following examples:

Examples

The sample output in these examples uses the following configuration: 

interface POS2/0
 no ip address
 encapsulation frame-relay
 frame-relay map ip 10.1.1.1 20 tcp header-compression
 frame-relay map ip 10.1.2.1 21 tcp header-compression
 frame-relay map ip 10.1.3.1 22 tcp header-compression
 frame-relay map bridge 23
 frame-relay interface-dlci 25
 frame-relay interface-dlci 26
 bridge-group 1
interface POS2/0.1 point-to-point
 frame-relay interface-dlci 24 protocol ip 10.1.4.1
interface Serial3/0
 no ip address
 encapsulation frame-relay
 serial restart-delay 0
 frame-relay map ip 172.16.3.1 20
 frame-relay map ip 172.16.4.1 21 tcp header-compression active
 frame-relay map ip 172.16.1.1 100
 frame-relay map ip 172.16.2.1 101
interface Serial3/0.1 multipoint
 frame-relay map ip 192.168.11.11 24
 frame-relay map ip 192.168.11.22 105

The following example shows how to display all maps: 

Router# show frame-relay map
POS2/0 (up): ip 10.1.1.1 dlci 20(0x14,0x440), static,
              CISCO, status deleted
              TCP/IP Header Compression (enabled), connections: 256
POS2/0 (up): ip 10.1.2.1 dlci 21(0x15,0x450), static,
              CISCO, status deleted
              TCP/IP Header Compression (enabled), connections: 256
POS2/0 (up): ip 10.1.3.1 dlci 22(0x16,0x460), static,
              CISCO, status deleted
              TCP/IP Header Compression (enabled), connections: 256
POS2/0 (up): bridge dlci 23(0x17,0x470), static,
              CISCO, status deleted
POS2/0.1 (down): point-to-point dlci, dlci 24(0x18,0x480), broadcast
          status deleted
Serial3/0 (downup): ip 172.16.3.1 dlci 20(0x14,0x440), static,
              CISCO, status deleted
Serial3/0 (downup): ip 172.16.4.1 dlci 21(0x15,0x450), static,
              CISCO, status deleted
              TCP/IP Header Compression (enabled), connections: 256
Serial3/0.1 (downup): ip 192.168.11.11 dlci 24(0x18,0x480), static,
              CISCO, status deleted
Serial3/0 (downup): ip 172.16.1.1 dlci 100(0x64,0x1840), static,
              CISCO, status deleted
Serial3/0 (downup): ip 172.16.2.1 dlci 101(0x65,0x1850), static,, CISCO, 
              CISCO, status deleted
              ECRTP Header Compression (enabled, IETF), connections 16
              TCP/IP Header Compression (enabled, IETF), connections 16 
Serial3/0.1 (downup): ip 192.168.11.22 dlci 105(0x69,0x1890), static,
              CISCO, status deleted
Serial4/0/1:0.1 (up): point-to-point dlci, dlci 102(0x66,0x1860), broadcast, CISCO
          status defined, active,
              RTP Header Compression (enabled), connections: 256

The following example shows how to display maps for a specific DLCI: 

Router# show frame-relay map 20
POS2/0 (up): ip 10.1.1.1 dlci 20(0x14,0x440), static,
              CISCO, status deleted
              TCP/IP Header Compression (enabled), connections: 256
Serial3/0 (down): ip 172.16.3.1 dlci 20(0x14,0x440), static,
              CISCO, status deleted

The following example shows how to display maps for a specific interface: 

Router# show frame-relay map interface pos2/0
POS2/0 (up): ip 10.1.1.1 dlci 20(0x14,0x440), static,
              CISCO, status deleted
              TCP/IP Header Compression (enabled), connections: 256
POS2/0 (up): ip 10.1.2.1 dlci 21(0x15,0x450), static,
              CISCO, status deleted
              TCP/IP Header Compression (enabled), connections: 256
POS2/0 (up): ip 10.1.3.1 dlci 22(0x16,0x460), static,
              CISCO, status deleted
              TCP/IP Header Compression (enabled), connections: 256
POS2/0 (up): bridge dlci 23(0x17,0x470), static,
              CISCO, status deleted
POS2/0.1 (down): point-to-point dlci, dlci 24(0x18,0x480), broadcast
          status deleted

The following example shows how to display maps for a specific DLCI on a specific interface: 

Router# show frame-relay map interface pos2/0 20
POS2/0 (up): ip 10.1.1.1 dlci 20(0x14,0x440), static,
              CISCO, status deleted
              TCP/IP Header Compression (enabled), connections: 256

The following example shows how to display maps for a specific subinterface: 

Router# show frame-relay map interface pos2/0.1
POS2/0.1 (down): point-to-point dlci, dlci 24(0x18,0x480), broadcast
          status deleted

The following example shows how to display maps for a specific DLCI on a specific subinterface: 

Router# show frame-relay map interface pos2/0.1 24
POS2/0.1 (down): point-to-point dlci, dlci 24(0x18,0x480), broadcast
          status deleted

Examples

The sample output in this example uses the following router configuration: 

hostname router1
!
interface Serial2/0
 ip address 10.0.0.2 255.255.255.0
 encapsulation frame-relay
 frame-relay vc-bundle vcb1
  pvc 100 vcb1-classA
   precedence 1-7
   class vcb1-classA
  pvc 109 vcb1-others
   precedence other
   class others
 frame-relay intf-type dce
!
map-class frame-relay vcb1-classA
 frame-relay cir 128000
!
map-class frame-relay others
 frame-relay cir 64000
hostname router2
!
interface Serial3/3
 ip address 10.0.0.1 255.255.255.0
 encapsulation frame-relay
 frame-relay vc-bundle vcb1
  pvc 100 vcb1-classA
   precedence 1-7
   class vcb1-classA
  pvc 109 vcb1-others
   precedence other
   class others
!
map-class frame-relay vcb1-classA
 frame-relay cir 128000
!
map-class frame-relay others
 frame-relay cir 64000

The following sample output displays mapping information for two PVC bundles. The PVC bundle MAIN-1-static is configured with a static map. The map for PVC bundle MAIN-2-dynamic is created dynamically using Inverse Address Resolution Protocol (ARP). 

Router# show frame-relay map 
Serial1/4 (up): ip 10.1.1.1 vc-bundle MAIN-1-static, static, 
          CISCO, status up
Serial1/4 (up): ip 10.1.1.2 vc-bundle MAIN-2-dynamic, dynamic, 
          broadcast, status up

Examples

The sample output in this example uses the following router configuration: 

hostname router1
!
interface Serial2/0
 no ip address
 encapsulation frame-relay
!
interface Serial2/0.1 point-to-point
 ipv6 address 1::1/64
 frame-relay interface-dlci 101   
!
interface Serial2/0.2 multipoint
 ipv6 address 2::1/64
 frame-relay map ipv6 2::2 201
 frame-relay interface-dlci 201   
! 
 
hostname router2
!
interface Serial3/3
 no ip address
 encapsulation frame-relay
 frame-relay intf-type dce
!
interface Serial3/3.1 point-to-point
 ipv6 address 1::2/64
 frame-relay interface-dlci 101   
!
interface Serial3/3.2 multipoint
 ipv6 address 2::2/64
 frame-relay map ipv6 3::1 201
 frame-relay interface-dlci 201
!

The following sample output from the show frame-relay map command shows that the link-local and global IPv6 addresses (FE80::E0:F727:E400:A and 2001:0DB8:2222:1044::32; FE80::60:3E47:AC8:8 and 2001:0DB8:2222:1044::32) of two remote nodes are explicitly mapped to DLCI 17 and DLCI 19, respectively. Both DLCI 17 and DLCI 19 are terminated on interface serial 3 of this node; therefore, interface serial 3 of this node is a point-to-multipoint interface. 

Router# show frame-relay map 
Serial3 (up): ipv6 FE80::E0:F727:E400:A dlci 17(0x11,0x410), static, 
              broadcast, CISCO, status defined, active 
Serial3 (up): ipv6 2001:0DB8:2222:1044::32 dlci 19(0x13,0x430), static, 
              CISCO, status defined, active 
Serial3 (up): ipv6 2001:0DB8:2222:1044::32 dlci 17(0x11,0x410), static, 
              CISCO, status defined, active 
Serial3 (up): ipv6 FE80::60:3E47:AC8:8 dlci 19(0x13,0x430), static, 
              broadcast, CISCO, status defined, active

The table below describes the significant fields shown in the displays.

Table 18 show frame-relay map Field Descriptions

Field

Description

POS2/0 (up)

Identifies a Frame Relay interface and its status (up or down).

ip 10.1.1.1

Destination IP address.

dlci 20(0x14,0x440)

DLCI that identifies the logical connection being used to reach this interface. This value is displayed in three ways: its decimal value (20), its hexadecimal value (0x14), and its value as it would appear on the wire (0x440).

vc-bundle

PVC bundle that serves as the logical connection being used to reach the interface.

static/dynamic

Indicates whether this is a static or dynamic entry.

broadcast

Indicates pseudobroadcasting.

CISCO

Indicates the encapsulation type for this map: either CISCO or IETF.

TCP/IP Header Compression (inherited), passive (inherited)

Indicates the header compression type (TCP/IP, Real-Time Transport Protocol (RTP), or Enhanced Compressed Real-Time Transport Protocol (ECRTP)) and whether the header compression characteristics were inherited from the interface or were explicitly configured for the IP map.

status defined, active

Indicates that the mapping between the destination address and the DLCI used to connect to the destination address is active.

Related Commands

Command

Description

show frame-relay pvc

Displays statistics about PVCs for Frame Relay interfaces.

show frame-relay vc-bundle

Displays attributes and other information about a Frame Relay PVC bundle.

show frame-relay multilink

To display configuration information and statistics about multilink Frame Relay bundles and bundle links, use the show frame-relay multilink command in user EXEC or privileged EXEC mode.

show frame-relay multilink [ mfr number | serial number ] [ dlci { dlci-number | lmi } ] [detailed]

Syntax Description

mfr number

(Optional) Displays information about a specific bundle interface.

serial number

(Optional) Displays information about a specific bundle link interface.

dlci

(Optional) Displays information about the data-link connection identifier (DLCI).

dlci-number

DLCI number. The range is from 16 to 1022.

lmi

Displays information about the Local Management Interface (LMI) DLCI.

detailed

(Optional) Displays more-detailed information, including counters for the control messages sent to and from the peer device and the status of the bundle links.

Command Default

Information for all bundles and bundle links is displayed.

Command Modes


User EXEC (>)
Privileged EXEC (#)

Command History

Release

Modification

12.0(17)S

This command was introduced.

12.2(8)T

This command was integrated into Cisco IOS Release 12.2(8)T.

12.0(24)S

This command was implemented on VIP-enabled Cisco 7500 series routers.

12.2(14)S

This command was integrated into Cisco IOS Release 12.2(14)S.

12.3(4)T

This command was implemented on VIP-enabled Cisco 7500 series routers.

12.0(30)S

This command was updated to display Multilink Frame Relay variable bandwidth class status.

12.4(2)T

This command was updated to display Multilink Frame Relay variable bandwidth class status.

12.2(28)SB

This command was integrated into Cisco IOS Release 12.2(28)SB.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command was integrated into the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

12.0(33)S

Support for IPv6 was added. This command was implemented on the Cisco 12000 series routers.

Examples

Examples

The following is sample output from the show frame-relay multilink command (see the table below for descriptions of the fields). Because a specific bundle or bundle link is not specified, information for all bundles and bundle links is displayed: 

Router# show frame-relay multilink
 
Bundle:MFR0, State = up, class = A, fragmentation disabled
 BID = MFR0
 Bundle links :
 Serial2/1:3, HW state :up, Protocol state :Idle, LID :Serial2/1:3
 Serial2/1:2, HW state :up, Protocol state :Idle, LID :Serial2/1:2
 Serial2/1:1, HW state :up, Protocol state :Idle, LID :Serial2/1:1

The following is sample output from the show frame-relay multilink command when a Frame Relay bundle is configured as bandwidth class C (threshold) (see the table below for descriptions of the fields): 

Router# show frame-relay multilink
 
Bundle: MFR0, state down, class C (threshold 2), no fragmentation
 ID: bundle
 Serial5/1, state up/up, ID: bundle1
 Serial5/3, state up/add-sent, ID: bundle3

Examples

The following is sample output from the show frame-relay multilink command when it is entered with the serialnumber keyword and argument pair (see the table below for descriptions of the fields). The example displays information about the specified bundle link: 

Router# show frame-relay multilink serial 3/2
 Bundle links :
 Serial3/2, HW state : down, Protocol state :Down_idle, LID :Serial3/2
 Bundle interface = MFR0,  BID = MFR0

Examples

The following is sample output from the show frame-relay multilink command when it is entered with the serialnumber keyword and argument pair and detailed keyword (see the table below for descriptions of the fields). The example shows a bundle link in the “idle” state: 

Router# show frame-relay multilink serial 3 detailed
 Bundle links:
  Serial3, HW state = up, link state = Idle, LID = Serial3
  Bundle interface = MFR0,  BID = MFR0
    Cause code = none, Ack timer = 4, Hello timer = 10,
    Max retry count = 2, Current count = 0,
    Peer LID = Serial5/3, RTT = 0 ms
    Statistics:
    Add_link sent = 0, Add_link rcv'd = 10,
    Add_link ack sent = 0, Add_link ack rcv'd = 0,
    Add_link rej sent = 10, Add_link rej rcv'd = 0,
    Remove_link sent = 0, Remove_link rcv'd = 0,
    Remove_link_ack sent = 0, Remove_link_ack rcv'd = 0,
    Hello sent = 0, Hello rcv'd = 0,
    Hello_ack sent = 0, Hello_ack rcv'd = 0,
    outgoing pak dropped = 0, incoming pak dropped = 0

The following is sample output from the show frame-relay multilink command when it is entered with the serialnumber keyword and argument pair and detailed keyword (see the table below for descriptions of the fields). The example shows a bundle link in the “up” state: 

Router# show frame-relay multilink serial 3 detailed
 Bundle links:
  Serial3, HW state = up, link state = Up, LID = Serial3
  Bundle interface = MFR0,  BID = MFR0
    Cause code = none, Ack timer = 4, Hello timer = 10,
    Max retry count = 2, Current count = 0,
    Peer LID = Serial5/3, RTT = 4 ms
    Statistics:
    Add_link sent = 1, Add_link rcv'd = 20,
    Add_link ack sent = 1, Add_link ack rcv'd = 1,
    Add_link rej sent = 19, Add_link rej rcv'd = 0,
    Remove_link sent = 0, Remove_link rcv'd = 0,
    Remove_link_ack sent = 0, Remove_link_ack rcv'd = 0,
    Hello sent = 0, Hello rcv'd = 1,
    Hello_ack sent = 1, Hello_ack rcv'd = 0,
    outgoing pak dropped = 0, incoming pak dropped = 0

The table below describes significant fields shown in the displays.

Table 19 show frame-relay multilink Field Descriptions

Field

Description

Bundle

Bundle interface.

State

Operational state of the bundle interface.

class

The bandwidth class criterion used to activate or deactivate a Frame Relay bundle.

  • Class A (single link)--The bundle activates when any bundle link is up and deactivates when all bundle links are down (default).

  • Class B (all links)--The bundle activates when all bundle links are up and deactivates when any bundle link is down.

  • Class C (threshold)--The bundle activates when the minimum configured number of bundle links (the threshold) is up and deactivates when the minimum number of configured bundle links fails to meet the threshold.

BID

Bundle identification.

Bundle links

Bundle links for which information is displayed.

HW state

Operational state of the physical link.

Protocol state

Operational state of the bundle link line protocol.

link state

Operational state of the bundle link.

LID

Bundle link identification.

Bundle interface

Bundle interface with which the bundle link is associated.

Cause code

Can be one of the following values:

  • ack timer expiry--Add link synchronization process is exhausted.

  • bundle link idle--Peer’s bundle link is idle. This usually occurs when the peer’s bundle interface is shut down.

  • inconsistent bundle--Peer already has this bundle associated with another bundle.

  • loopback detected--Local bundle link’s physical line is looped back.

  • none--ADD_LINK and ADD_LINK_ACK messages were properly exchanged, and no cause code was recorded.

  • other--Indicates one of the following: a link identifier (LID) mismatch, an ID from the peer that is too long, or a failure to allocate ID memory.

  • unexpected Add_link--ADD_LINK message is received when the bundle link is already in the “up” state. This code might appear when the line protocol is being set up, but will disappear once the connection is stabilized.

Ack timer

Number of seconds for which the bundle link waits for a hello acknowledgment before resending a hello message or resending an ADD_LINK message used for initial synchronization.

Hello timer

Interval at which a bundle link sends out hello messages.

Max retry count

Maximum number of times that a bundle link will resend a hello message before receiving an acknowledgment or resending an ADD_LINK message.

Current count

Number of retries that have been attempted.

Peer LID

Bundle link identification name of the peer end of the link.

RTT

Round-trip time (in milliseconds) as measured by using the Timestamp Information Element in the HELLO and HELLO_ACK messages.

Statistics

Displays statistics for each bundle link.

Add_link sent

Number of Add_link messages sent. Add_link messages notify the peer endpoint that the local endpoint is ready to process frames.

Add_link rcv’d

Number of Add_link messages received.

Add_link ack sent

Number of Add_link acknowledgments sent. Add_link acknowledgments notify the peer endpoint that an Add_link message was received.

Add_link ack rcv’d

Number of Add_link acknowledgments received.

Add_link rej sent

Number of Add_link_reject messages sent.

Add_link rej rcv’d

Number of Add_link_reject messages received.

Remove_link sent

Number of Remove_link messages sent. Remove_link messages notify the peer that on the local end a bundle link is being removed from the bundle.

Remove_link rcv’d

Number of Remove_link messages received.

Remove_link_ack sent

Number of Remove_link acknowledgments sent. Remove_link acknowledgments notify the peer that a Remove_link message has been received.

Remove_link_ack rcv’d

Number of Remove_link acknowledgments received.

Hello sent

Number of hello messages sent. Hello messages notify the peer endpoint that the local endpoint remains in the “up” state.

Hello rcv’d

Number of hello messages received.

Hello_ack sent

Number of hello acknowledgments sent. Hello acknowledgments notify the peer that hello messages have been received.

Hello_ack rcv’d

Number of hello acknowledgments received.

outgoing pak dropped

Number of outgoing packets dropped.

incoming pak dropped

Number of incoming packets dropped.

Related Commands

Command

Description

debug frame-relay multilink

Displays debug messages for multilink Frame Relay bundles and bundle links.

show frame-relay pvc

To display statistics about Frame Relay permanent virtual circuits (PVCs), use the show frame-relay pvc command in privileged EXEC mode.

show frame-relay pvc [ [ interface interface ] [ dlci ] [ 64-bit ] | summary [ all ] ]

Syntax Description

interface

(Optional) Specific interface for which PVC information will be displayed.

interface

(Optional) Interface number containing the data-link connection identifiers (DLCIs) for which you wish to display PVC information.

dlci

(Optional) A specific DLCI number used on the interface. Statistics for the specified PVC are displayed when a DLCI is also specified.

64-bit

(Optional) Displays 64-bit counter statistics.

summary

(Optional) Displays a summary of all PVCs on the system.

all

(Optional) Displays a summary of all PVCs on each interface.

Command Modes


Privileged EXEC

Command History

Release

Modification

10.0

This command was introduced.

12.0(1)T

This command was modified to display statistics about virtual access interfaces used for PPP connections over Frame Relay.

12.0(3)XG

This command was modified to include the fragmentation type and size associated with a particular PVC when fragmentation is enabled on the PVC.

12.0(4)T

This command was modified to include the fragmentation type and size associated with a particular PVC when fragmentation is enabled on the PVC.

12.0(5)T

This command was modified to include information on the special voice queue that is created using the queue keyword of the frame-relay voice bandwidth command.

12.1(2)T

This command was modified to display the following information:

  • Details about the policy map attached to a specific PVC.

  • The priority configured for PVCs within Frame Relay PVC interface priority queueing.

  • Details about Frame Relay traffic shaping and policing on switched PVCs.

12.0(12)S

This command was modified to display reasons for packet drops and complete status information for switched NNI PVCs.

12.1(5)T

This command was modified to display the following information:

  • The number of packets in the post-hardware-compression queue.

  • The reasons for packet drops and complete status information for switched network-to-network PVCs.

12.0(17)S

This command was modified to display the number of outgoing packets dropped and the number of outgoing bytes dropped because of QoS policy.

12.2 T

This command was modified to show that when payload compression is configured for a PVC, the throughput rate reported by the PVC is equal to the rate reported by the interface.

12.2(4)T

The 64-bit keyword was added.

12.2(11)T

This command was modified to display the number of outgoing packets dropped and the number of outgoing bytes dropped because of QoS policy.

12.2(13)T

This command was modified to support display of Frame Relay PVC bundle information.

12.2(15)T

This command was modified to support display of Frame Relay voice-adaptive fragmentation information.

12.2(27)SBC

This command was integrated into Cisco IOS Release 12.2(27)SBC, and the summary and all keywords were added.

12.2(28)SB

This command was integrated into Cisco IOS Release 12.2(28)SB, and support was added for hierarchical queueing framework (HQF).

12.4(9)T

The summary and all keywords were added, and support was added for hierarchical queueing framework (HQF).

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

12.0(33)S

Support for IPv6 was added. This command was implemented on the Cisco 12000 series routers.

Usage Guidelines

Use this command to monitor the PPP link control protocol (LCP) state as being open with an up state or closed with a down state.

When “vofr” or “vofr cisco” has been configured on the PVC, and a voice bandwidth has been allocated to the class associated with this PVC, configured voice bandwidth and used voice bandwidth are also displayed.

Statistics Reporting

To obtain statistics about PVCs on all Frame Relay interfaces, use this command with no arguments.

To obtain statistics about a PVC that include policy-map configuration or the priority configured for that PVC, use this command with the dlci argument.

To display a summary of all PVCs on the system, use the show frame-relay pvc command with the summary keyword. To display a summary of all PVCs per interface, use the summary allkeywords.

Per-VC counters are not incremented at all when either autonomous or silicon switching engine (SSE) switching is configured; therefore, PVC values will be inaccurate if either switching method is used.

You can change the period of time over which a set of data is used for computing load statistics. If you decrease the load interval, the average statistics are computed over a shorter period of time and are more responsive to bursts of traffic. To change the length of time for which a set of data is used to compute load statistics for a PVC, use the load-interval command in Frame-Relay DLCI configuration mode.

Traffic Shaping

Congestion control mechanisms are currently not supported on terminated PVCs nor on PVCs over ISDN. Where congestion control mechanisms are supported, the switch passes forward explicit congestion notification (FECN) bits, backward explicit congestion notification (BECN) bits, and discard eligible (DE) bits unchanged from entry points to exit points in the network.

Examples

The various displays in this section show sample output for a variety of PVCs. Some of the PVCs carry data only; some carry a combination of voice and data. This section contains the following examples:

The following example shows sample output of the show frame-relay pvc command with the summary keyword. The summary keyword displays all PVCs on the system. 

Router# show frame-relay pvc summary 
         
Frame-Relay VC Summary
              Active     Inactive      Deleted       Static
  Local          0           12            0            0
  Switched       0            0            0            0
  Unused         0            0            0            0

The following example shows sample output for the show frame-relay pvc command with the summaryand all keywords. The summary and all keywords display all PVCs per interface. 

Router# show frame-relay pvc summary all
VC Summary for interface Serial3/0 (Frame Relay DTE)
              Active     Inactive      Deleted       Static
  Local          0            7            0            0
  Switched       0            0            0            0
  Unused         0            0            0            0
VC Summary for interface Serial3/1 (Frame Relay DTE)
              Active     Inactive      Deleted       Static
  Local          0            5            0            0
  Switched       0            0            0            0
  Unused         0            0            0            0

The following sample output shows a generic Frame Relay configuration on DLCI 100: 

Router# show frame-relay pvc 100
PVC Statistics for interface Serial4/0/1:0 (Frame Relay DTE)
DLCI = 100, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE (EEK UP), INTERFACE = Serial4/0/1:0.1
  input pkts 4360          output pkts 4361         in bytes 146364    
  out bytes 130252         dropped pkts 3735        in pkts dropped 0         
  out pkts dropped 3735             out bytes dropped 1919790
  late-dropped out pkts 3735        late-dropped out bytes 1919790
  in FECN pkts 0           in BECN pkts 0           out FECN pkts 0         
  out BECN pkts 0          in DE pkts 0             out DE pkts 0         
  out bcast pkts 337       out bcast bytes 102084    
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
  pvc create time 05:34:06, last time pvc status changed 05:33:38

The following sample output indicates that Frame Relay voice-adaptive fragmentation is active on DLCI 202 and there are 29 seconds left on the deactivation timer. If no voice packets are detected in the next 29 seconds, Frame Relay voice-adaptive fragmentation will become inactive. 

Router# show frame-relay pvc 202
        
PVC Statistics for interface Serial3/1 (Frame Relay DTE)
        
DLCI = 202, DLCI USAGE = LOCAL, PVC STATUS = STATIC, INTERFACE = Serial3/1.2
          
  input pkts 0             output pkts 479          in bytes 0
  out bytes 51226          dropped pkts 0           in pkts dropped 0
  out pkts dropped 0                out bytes dropped 0
  in FECN pkts 0           in BECN pkts 0           out FECN pkts 0
  out BECN pkts 0          in DE pkts 0             out DE pkts 0
  out bcast pkts 0         out bcast bytes 0
  5 minute input rate 0 bits/sec, 0 packets/sec 
  5 minute output rate 5000 bits/sec, 5 packets/sec
  pvc create time 00:23:36, last time pvc status changed 00:23:31     
  fragment type end-to-end fragment size 80 adaptive active, time left 29 secs

The following sample output indicates that PVC 202 is a member of VC bundle MAIN-1-static: 

Router# show frame-relay pvc 202
PVC Statistics for interface Serial1/4 (Frame Relay DTE)
DLCI = 202, DLCI USAGE = LOCAL, PVC STATUS = STATIC, INTERFACE = Serial1/4
  input pkts 0             output pkts 45           in bytes 0
  out bytes 45000          dropped pkts 0           in FECN pkts 0
  in BECN pkts 0           out FECN pkts 0          out BECN pkts 0
  in DE pkts 0             out DE pkts 0
  out bcast pkts 0         out bcast bytes 0
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 2000 bits/sec, 2 packets/sec
  pvc create time 00:01:25, last time pvc status changed 00:01:11
  VC-Bundle MAIN-1-static

The following sample output displays the Frame Relay 64-bit counters: 

Router# show frame-relay pvc 35 64-bit
DLCI = 35, INTERFACE = Serial0/0
  input pkts 0                       output pkts 0
  in bytes 0                         out bytes 0

The following is sample output for the show frame-relay pvccommand for a PVC configured with Cisco-proprietary fragmentation and hardware compression: 

Router# show frame-relay pvc 110
PVC Statistics for interface Serial0/0 (Frame Relay DTE)
DLCI = 110, DLCI USAGE = LOCAL, PVC STATUS = STATIC, INTERFACE = Serial0/0
  input pkts 409           output pkts 409          in bytes 3752      
  out bytes 4560           dropped pkts 1           in FECN pkts 0         
  in BECN pkts 0           out FECN pkts 0          out BECN pkts 0         
  in DE pkts 0             out DE pkts 0         
  out bcast pkts 0          out bcast bytes 0         
  pvc create time 3d00h, last time pvc status changed 2d22h
  Service type VoFR-cisco
   Voice Queueing Stats: 0/100/0 (size/max/dropped)
  Post h/w compression queue: 0
  Current fair queue configuration:
   Discard     Dynamic      Reserved
   threshold   queue count  queue count
   64          16           2    
  Output queue size 0/max total 600/drops 0
  configured voice bandwidth 16000, used voice bandwidth 0
  fragment type VoFR-cisco         fragment size 100
  cir 64000     bc   640       be 0         limit 80     interval 10  
  mincir 32000     byte increment 80    BECN response no 
  frags 428       bytes 4810      frags delayed 24        bytes delayed 770      
  shaping inactive    
  traffic shaping drops 0
  ip rtp priority parameters 16000 32000 20000

The following is sample output from the show frame-relay pvc command for a switched Frame Relay PVC. This output displays detailed information about Network-to-Network Interface (NNI) status and why packets were dropped from switched PVCs. 

Router# show frame-relay pvc
 PVC Statistics for interface Serial2/2 (Frame Relay NNI) 
 DLCI = 16, DLCI USAGE = SWITCHED, PVC STATUS = INACTIVE, INTERFACE = Serial2/2 
 LOCAL PVC STATUS = INACTIVE, NNI PVC STATUS = INACTIVE
   input pkts 0             output pkts 0            in bytes 0 
   out bytes 0              dropped pkts 0           in FECN pkts 0 
   in BECN pkts 0           out FECN pkts 0          out BECN pkts 0 
   in DE pkts 0             out DE pkts 0 
   out bcast pkts 0         out bcast bytes 0 
   switched pkts0 
   Detailed packet drop counters: 
   no out intf 0            out intf down 0          no out PVC 0 
   in PVC down 0            out PVC down 0           pkt too big 0 
   shaping Q full 0         pkt above DE 0           policing drop 0 
   pvc create time 00:00:07, last time pvc status changed 00:00:07

The following is sample output from the show frame-relay pvc command that shows the statistics for a switched PVC on which Frame Relay congestion management is configured: 

Router# show frame-relay pvc 200
  
PVC Statistics for interface Serial3/0 (Frame Relay DTE)
  
DLCI = 200, DLCI USAGE = SWITCHED, PVC STATUS = ACTIVE, INTERFACE = Serial3/0
  input pkts 341           output pkts 390          in bytes 341000
  out bytes 390000         dropped pkts 0           in FECN pkts 0
  in BECN pkts 0           out FECN pkts 0          out BECN pkts 0
  in DE pkts 0             out DE pkts 390
  out bcast pkts 0          out bcast bytes 0            Num Pkts Switched 341
  pvc create time 00:10:35, last time pvc status changed 00:10:06
  Congestion DE threshold 50 
  shaping active 
  cir 56000     bc 7000      be 0         byte limit 875    interval 125
  mincir 28000     byte increment 875   BECN response no
  pkts 346       bytes 346000    pkts delayed 339       bytes delayed 339000
  traffic shaping drops 0
  Queueing strategy:fifo
  Output queue 48/100, 0 drop, 339 dequeued

The following is sample output from the show frame-relay pvc command that shows the statistics for a switched PVC on which Frame Relay policing is configured: 

Router# show frame-relay pvc 100
PVC Statistics for interface Serial1/0 (Frame Relay DCE)
DLCI = 100, DLCI USAGE = SWITCHED, PVC STATUS = ACTIVE, INTERFACE = Serial1/0  
  input pkts 1260          output pkts 0            in bytes 1260000
  out bytes 0              dropped pkts 0           in FECN pkts 0
  in BECN pkts 0           out FECN pkts 0          out BECN pkts 0
  in DE pkts 0             out DE pkts 0
  out bcast pkts 0          out bcast bytes 0            Num Pkts Switched 1260
  pvc create time 00:03:57, last time pvc status changed 00:03:19
  policing enabled, 180 pkts marked DE
  policing Bc  6000        policing Be  6000        policing Tc  125 (msec)
  in Bc pkts   1080        in Be pkts   180         in xs pkts   0
  in Bc bytes  1080000     in Be bytes  180000      in xs bytes  0

The following is sample output for a PVC that has been assigned high priority: 

Router# show frame-relay pvc 100
PVC Statistics for interface Serial0 (Frame Relay DTE)
DLCI = 100, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0
  
  input pkts 0             output pkts 0            in bytes 0
  out bytes 0              dropped pkts 0           in FECN pkts 0
  in BECN pkts 0           out FECN pkts 0          out BECN pkts 0
  in DE pkts 0             out DE pkts 0
  out bcast pkts 0          out bcast bytes 0
  pvc create time 00:00:59, last time pvc status changed 00:00:33
  priority high

The following is sample output from the show frame-relay pvc command for a PVC shaped to a 64000 bps committed information rate (CIR) with fragmentation. A policy map is attached to the PVC and is configured with a priority class for voice, two data classes for IP precedence traffic, and a default class for best-effort traffic. Weighted Random Early Detection (WRED) is used as the drop policy on one of the data classes. 

Router# show frame-relay pvc 100
PVC Statistics for interface Serial1/0 (Frame Relay DTE)
DLCI = 100, DLCI USAGE = LOCAL, PVC STATUS = INACTIVE, INTERFACE = Serial1/0.1
  input pkts 0             output pkts 0            in bytes 0         
  out bytes 0              dropped pkts 0           in FECN pkts 0         
  in BECN pkts 0           out FECN pkts 0          out BECN pkts 0         
  in DE pkts 0             out DE pkts 0         
  out bcast pkts 0          out bcast bytes 0         
  pvc create time 00:00:42, last time pvc status changed 00:00:42
  service policy mypolicy
 Class voice
  Weighted Fair Queueing
      Strict Priority
      Output Queue: Conversation 72 
        Bandwidth 16 (kbps) Packets Matched 0
        (pkts discards/bytes discards) 0/0
 Class immediate-data
  Weighted Fair Queueing
      Output Queue: Conversation 73 
        Bandwidth 60 (%) Packets Matched 0
        (pkts discards/bytes discards/tail drops) 0/0/0
        mean queue depth: 0
        drops: class  random   tail     min-th   max-th   mark-prob 
               0      0        0        64       128      1/10
               1      0        0        71       128      1/10
               2      0        0        78       128      1/10
               3      0        0        85       128      1/10
               4      0        0        92       128      1/10
               5      0        0        99       128      1/10
               6      0        0        106      128      1/10
               7      0        0        113      128      1/10
               rsvp   0        0        120      128      1/10
 Class priority-data
  Weighted Fair Queueing
      Output Queue: Conversation 74 
        Bandwidth 40 (%) Packets Matched 0 Max Threshold 64 (packets)
        (pkts discards/bytes discards/tail drops) 0/0/0
 Class class-default
  Weighted Fair Queueing
      Flow Based Fair Queueing
      Maximum Number of Hashed Queues 64  Max Threshold 20 (packets)
  Output queue size 0/max total 600/drops 0
  fragment type end-to-end         fragment size 50
  cir 64000     bc   640       be 0         limit 80     interval 10  
  mincir 64000     byte increment 80    BECN response no 
  frags 0         bytes 0         frags delayed 0         bytes delayed 0        
  shaping inactive    
  traffic shaping drops 0

The following is sample output from the show frame-relay pvc command that shows the PVC statistics for serial interface 5 (slot 1 and DLCI 55 are up) during a PPP session over Frame Relay: 

Router# show frame-relay pvc 55
PVC Statistics for interface Serial5/1 (Frame Relay DTE)
DLCI = 55, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial5/1.1
     input pkts 9             output pkts 16           in bytes 154
     out bytes 338            dropped pkts 6           in FECN pkts 0
     in BECN pkts 0           out FECN pkts 0          out BECN pkts 0
     in DE pkts 0             out DE pkts 0
     out bcast pkts 0         out bcast bytes 0
     pvc create time 00:35:11, last time pvc status changed 00:00:22
     Bound to Virtual-Access1 (up, cloned from Virtual-Template5)

The following is sample output from the show frame-relay pvc command for a PVC carrying Voice over Frame Relay (VoFR) traffic configured via the vofr cisco command. The frame-relay voice bandwidth command has been configured on the class associated with this PVC, as has fragmentation. The fragmentation type employed is proprietary to Cisco.

A sample configuration for this situation is shown first, followed by the output for the show frame-relay pvc command. 

interface serial 0
 encapsulation frame-relay
 frame-relay traffic-shaping
 frame-relay interface-dlci 108
  vofr cisco
  class vofr-class
map-class frame-relay vofr-class
 frame-relay fragment 100
 frame-relay fair-queue
 frame-relay cir 64000
 frame-relay voice bandwidth 25000
Router# show frame-relay pvc 108
PVC Statistics for interface Serial0 (Frame Relay DTE)
DLCI = 108, DLCI USAGE = LOCAL, PVC STATUS = STATIC, INTERFACE = Serial0
  input pkts 1260          output pkts 1271         in bytes 95671     
  out bytes 98604          dropped pkts 0           in FECN pkts 0         
  in BECN pkts 0           out FECN pkts 0          out BECN pkts 0         
  in DE pkts 0             out DE pkts 0         
  out bcast pkts 1271       out bcast bytes 98604     
  pvc create time 09:43:17, last time pvc status changed 09:43:17
  Service type VoFR-cisco
  configured voice bandwidth 25000, used voice bandwidth 0
  voice reserved queues 24, 25
  fragment type VoFR-cisco         fragment size 100
  cir 64000     bc 64000     be 0         limit 1000   interval 125 
  mincir 32000     byte increment 1000  BECN response no 
  pkts 2592      bytes 205140    pkts delayed 1296      bytes delayed 102570   
  shaping inactive    
  shaping drops 0
  Current fair queue configuration:
   Discard     Dynamic      Reserved
   threshold   queue count  queue count
    64          16           2    
  Output queue size 0/max total 600/drops 0

The following is sample output from the show frame-relay pvc command for an application employing pure FRF.12 fragmentation. A sample configuration for this situation is shown first, followed by the output for the show frame-relay pvc command. 

interface serial 0
 encapsulation frame-relay
 frame-relay traffic-shaping
 frame-relay interface-dlci 110
  class frag
map-class frame-relay frag
 frame-relay fragment 100
 frame-relay fair-queue
 frame-relay cir 64000
Router# show frame-relay pvc 110
PVC Statistics for interface Serial0 (Frame Relay DTE)
DLCI = 110, DLCI USAGE = LOCAL, PVC STATUS = STATIC, INTERFACE = Serial0
  input pkts 0             output pkts 243          in bytes 0         
  out bytes 7290           dropped pkts 0           in FECN pkts 0         
  in BECN pkts 0           out FECN pkts 0          out BECN pkts 0         
  in DE pkts 0             out DE pkts 0         
  out bcast pkts 243        out bcast bytes 7290      
  pvc create time 04:03:17, last time pvc status changed 04:03:18
  fragment type end-to-end         fragment size 100
  cir 64000     bc 64000     be 0         limit 1000   interval 125 
  mincir 32000     byte increment 1000  BECN response no 
  pkts 486       bytes 14580     pkts delayed 243       bytes delayed 7290     
  shaping inactive    
  shaping drops 0
  Current fair queue configuration:
   Discard     Dynamic      Reserved
   threshold   queue count  queue count
   64          16           2    
  Output queue size 0/max total 600/drops 0

Note that when voice is not configured, voice bandwidth output is not displayed.

The following is sample output from the show frame-relay pvc command for multipoint subinterfaces carrying data only. The output displays both the subinterface number and the DLCI. This display is the same whether the PVC is configured for static or dynamic addressing. Note that neither fragmentation nor voice is configured on this PVC. 

Router# show frame-relay pvc
DLCI = 300, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.103
input pkts 10  output pkts 7  in bytes 6222 
out bytes 6034  dropped pkts 0  in FECN pkts 0 
in BECN pkts 0  out FECN pkts 0  out BECN pkts 0 
in DE pkts 0  out DE pkts 0         
outbcast pkts 0  outbcast bytes 0
pvc create time 0:13:11  last time pvc status changed 0:11:46
DLCI = 400, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0.104
input pkts 20  output pkts 8  in bytes 5624 
out bytes 5222  dropped pkts 0  in FECN pkts 0 
in BECN pkts 0  out FECN pkts 0  out BECN pkts 0 
in DE pkts 0  out DE pkts 0         
outbcast pkts 0  outbcast bytes 0
pvc create time 0:03:57  last time pvc status changed 0:03:48

The following is sample output from the show frame-relay pvc command for a PVC when HQF is enabled: 

Router# show frame-relay pvc 16
PVC Statistics for interface Serial4/1 (Frame Relay DTE)
DLCI = 16, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial4/1
  input pkts 1             output pkts 1            in bytes 34
  out bytes 34             dropped pkts 0           in pkts dropped 0
  out pkts dropped 0                out bytes dropped 0
  in FECN pkts 0           in BECN pkts 0           out FECN pkts 0
  out BECN pkts 0          in DE pkts 0             out DE pkts 0
  out bcast pkts 1         out bcast bytes 34
  pvc create time 00:09:07, last time pvc status changed 00:09:07
  shaping inactive

The following is sample output from the show frame-relay pvc command for a PVC carrying voice and data traffic, with a special queue specifically for voice traffic created using the frame-relay voice bandwidth command queuekeyword : 

Router# show frame-relay pvc interface serial 1 45
  
 PVC Statistics for interface Serial1 (Frame Relay DTE)
  
 DLCI = 45, DLCI USAGE = LOCAL, PVC STATUS = STATIC, INTERFACE = Serial1
  
   input pkts 85            output pkts 289          in bytes 1730      
   out bytes 6580           dropped pkts 11          in FECN pkts 0         
   in BECN pkts 0           out FECN pkts 0          out BECN pkts 0         
   in DE pkts 0             out DE pkts 0         
   out bcast pkts 0          out bcast bytes 0         
   pvc create time 00:02:09, last time pvc status changed 00:02:09
   Service type VoFR
   configured voice bandwidth 25000, used voice bandwidth 22000
   fragment type VoFR         fragment size 100
   cir 20000     bc   1000      be 0         limit 125    interval 50  
   mincir 20000     byte increment 125   BECN response no 
   fragments 290       bytes 6613      fragments delayed 1         bytes delayed 33       
   shaping inactive    
   traffic shaping drops 0
    Voice Queueing Stats: 0/100/0 (size/max/dropped)
   ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
   Current fair queue configuration:
    Discard     Dynamic      Reserved
    threshold   queue count  queue count
    64          16           2    
   Output queue size 0/max total 600/drops 0

The table below describes the significant fields shown in the displays.

Table 20 show frame-relay pvc Field Descriptions

Field

Description

DLCI

One of the DLCI numbers for the PVC.

DLCI USAGE

Lists SWITCHED when the router or access server is used as a switch, or LOCAL when the router or access server is used as a DTE device.

PVC STATUS

Status of the PVC: ACTIVE, INACTIVE, or DELETED.

INTERFACE

Specific subinterface associated with this DLCI.

LOCAL PVC STATUS1

Status of PVC configured locally on the NNI interface.

NNI PVC STATUS 1

Status of PVC learned over the NNI link.

input pkts

Number of packets received on this PVC.

output pkts

Number of packets sent on this PVC.

in bytes

Number of bytes received on this PVC.

out bytes

Number of bytes sent on this PVC.

dropped pkts

Number of incoming and outgoing packets dropped by the router at the Frame Relay level.

in pkts dropped

Number of incoming packets dropped. Incoming packets may be dropped for a number of reasons, including the following:

  • Inactive PVC

  • Policing

  • Packets received above DE discard level

  • Dropped fragments

  • Memory allocation failures

  • Configuration problems

out pkts dropped

Number of outgoing packets dropped, including shaping drops and late drops.

out bytes dropped

Number of outgoing bytes dropped.

late-dropped out pkts

Number of outgoing packets dropped because of QoS policy (such as with VC queuing or Frame Relay traffic shaping). This field is not displayed when the value is zero.

late-dropped out bytes

Number of outgoing bytes dropped because of QoS policy (such with as VC queuing or Frame Relay traffic shaping). This field is not displayed when the value is zero.

in FECN pkts

Number of packets received with the FECN bit set.

in BECN pkts

Number of packets received with the BECN bit set.

out FECN pkts

Number of packets sent with the FECN bit set.

out BECN pkts

Number of packets sent with the BECN bit set.

in DE pkts

Number of DE packets received.

out DE pkts

Number of DE packets sent.

out bcast pkts

Number of output broadcast packets.

out bcast bytes

Number of output broadcast bytes.

switched pkts

Number of switched packets.

no out intf2

Number of packets dropped because there is no output interface.

out intf down 2

Number of packets dropped because the output interface is down.

no out PVC 2

Number of packets dropped because the outgoing PVC is not configured.

in PVC down 2

Number of packets dropped because the incoming PVC is inactive.

out PVC down 2

Number of packets dropped because the outgoing PVC is inactive.

pkt too big 2

Number of packets dropped because the packet size is greater than media MTU3.

shaping Q full 2

Number of packets dropped because the Frame Relay traffic-shaping queue is full.

pkt above DE 2

Number of packets dropped because they are above the DE level when Frame Relay congestion management is enabled.

policing drop 2

Number of packets dropped because of Frame Relay traffic policing.

pvc create time

Time at which the PVC was created.

last time pvc status changed

Time at which the PVC changed status.

VC-Bundle

PVC bundle of which the PVC is a member.

priority

Priority assigned to the PVC.

pkts marked DE

Number of packets marked DE because they exceeded the Bc.

policing Bc

Committed burst size.

policing Be

Excess burst size.

policing Tc

Measurement interval for counting Bc and Be.

in Bc pkts

Number of packets received within the committed burst.

in Be pkts

Number of packets received within the excess burst.

in xs pkts

Number of packets dropped because they exceeded the combined burst.

in Bc bytes

Number of bytes received within the committed burst.

in Be bytes

Number of bytes received within the excess burst.

in xs bytes

Number of bytes dropped because they exceeded the combined burst.

Congestion DE threshold

PVC queue percentage at which packets with the DE bit are dropped.

Congestion ECN threshold

PVC queue percentage at which packets are set with the BECN and FECN bits.

Service type

Type of service performed by this PVC. Can be VoFR or VoFR-cisco.

Post h/w compression queue

Number of packets in the post-hardware-compression queue when hardware compression and Frame Relay fragmentation are configured.

configured voice bandwidth

Amount of bandwidth in bits per second (bps) reserved for voice traffic on this PVC.

used voice bandwidth

Amount of bandwidth in bps currently being used for voice traffic.

service policy

Name of the output service policy applied to the VC.

Class

Class of traffic being displayed. Output is displayed for each configured class in the policy.

Output Queue

The WFQ4 conversation to which this class of traffic is allocated.

Bandwidth

Bandwidth in kbps or percentage configured for this class.

Packets Matched

Number of packets that matched this class.

Max Threshold

Maximum queue size for this class when WRED is not used.

pkts discards

Number of packets discarded for this class.

bytes discards

Number of bytes discarded for this class.

tail drops

Number of packets discarded for this class because the queue was full.

mean queue depth

Average queue depth, based on the actual queue depth on the interface and the exponential weighting constant. It is a moving average. The minimum and maximum thresholds are compared against this value to determine drop decisions.

drops:

WRED parameters.

class

IP precedence value.

random

Number of packets randomly dropped when the mean queue depth is between the minimum threshold value and the maximum threshold value for the specified IP precedence value.

tail

Number of packets dropped when the mean queue depth is greater than the maximum threshold value for the specified IP precedence value.

min-th

Minimum WRED threshold in number of packets.

max-th

Maximum WRED threshold in number of packets.

mark-prob

Fraction of packets dropped when the average queue depth is at the maximum threshold.

Maximum Number of Hashed Queues

(Applies to class default only) Number of queues available for unclassified flows.

fragment type

Type of fragmentation configured for this PVC. Possible types are as follows:

  • end-to-end--Fragmented packets contain the standard FRF.12 header

  • VoFR--Fragmented packets contain the FRF.11 Annex C header

  • VoFR-cisco--Fragmented packets contain the Cisco proprietary header

fragment size

Size of the fragment payload in bytes.

adaptive active/inactive

Indicates whether Frame Relay voice-adaptive fragmentation is active or inactive.

time left

Number of seconds left on the Frame Relay voice-adaptive fragmentation deactivation timer. When this timer expires, Frame Relay fragmentation turns off.

cir

Current CIR in bps.

bc

Current committed burst (Bc) size, in bits.

be

Current excess burst (Be) size, in bits.

limit

Maximum number of bytes sent per internal interval (excess plus sustained).

interval

Interval being used internally (may be smaller than the interval derived from Bc/CIR; this happens when the router determines that traffic flow will be more stable with a smaller configured interval).

mincir

Minimum CIR for the PVC.

byte increment

Number of bytes that will be sustained per internal interval.

BECN response

Indication that Frame Relay has BECN adaptation configured.

pkts

Number of packets associated with this PVC that have gone through the traffic-shaping system.

frags

Total number of fragments (and unfragmented packets that are too small to be fragmented) shaped on this VC.

bytes

Number of bytes associated with this PVC that have gone through the traffic-shaping system.

pkts delayed

Number of packets associated with this PVC that have been delayed by the traffic-shaping system.

frags delayed

Number of fragments (and unfragmented packets that are too small to be fragmented) delayed in the shaping queue before being sent.

bytes delayed

Number of bytes associated with this PVC that have been delayed by the traffic-shaping system.

shaping

Indication that shaping will be active for all PVCs that are fragmenting data; otherwise, shaping will be active if the traffic being sent exceeds the CIR for this circuit.

shaping drops

Number of packets dropped by the traffic-shaping process.

Queueing strategy

Per-VC queueing strategy.

Output queue

48/100

0 drop

300 dequeued

State of the per-VC queue.

  • Number of packets enqueued/size of the queue

  • Number of packets dropped

  • Number of packets dequeued

Voice Queueing Stats

Statistics showing the size of packets, the maximum number of packets, and the number of packets dropped in the special voice queue created using the frame-relay voice bandwidth command queuekeyword .

Discard threshold

Maximum number of packets that can be stored in each packet queue. Additional packets received after a queue is full will be discarded.

Dynamic queue count

Number of packet queues reserved for best-effort traffic.

Reserved queue count

Number of packet queues reserved for voice traffic.

Output queue size

Size in bytes of each output queue.

max total

Maximum number of packets of all types that can be queued in all queues.

drops

Number of frames dropped by all output queues.

1 The LOCAL PVC STATUS and NNI PVC STATUS fields are displayed only for PVCs configured on Frame Relay NNI interface types. These fields are not displayed if the PVC is configured on DCE or DTE interface types.
2 The detailed packet drop fields are displayed for switched Frame Relay PVCs only. These fields are not displayed for terminated PVCs.
3 MTU = maximum transmission unit.
4 WFQ = weighted fair queueing.

Related Commands

Command

Description

frame-relay accounting adjust

Enables byte count adjustment at the PVC level so that the number of bytes sent and received at the PVC corresponds to the actual number of bytes sent and received on the physical interface.

frame-relay interface-queue priority

Enables FR PIPQ on a Frame Relay interface and assigns priority to a PVC within a Frame Relay map class.

frame-relay pvc

Configures Frame Relay PVCs for FRF.8 Frame Relay-ATM Service Interworking.

service-policy

Attaches a policy map to an input interface or VC or an output interface or VC.

show dial-peer voice

Displays configuration information and call statistics for dial peers.

show frame-relay fragment

Displays Frame Relay fragmentation details.

show frame-relay map

Displays the current Frame Relay map entries and information about the connections

show frame-relay vc-bundle

Displays attributes and other information about a Frame Relay PVC bundle.

show frame-relay qos-autosense

To display the quality of service (QoS) values sensed from the switch, use the show frame-relay qos-autosense command in privileged EXEC mode.

show frame-relay qos-autosense [ interface number ]

Syntax Description

interface number

(Optional) Indicates the number of the physical interface for which you want to display QoS information.

Command Modes


Privileged EXEC

Command History

Release

Modification

11.2

This command was introduced.

12.1(3)T

This command was modified to display information about Enhanced Local Management Interface (ELMI) address registration.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

Examples

The following is sample output from the show frame-relay qos-autosensecommand when ELMI and ELMI address registration are enabled. 

Router# show frame-relay qos-autosense
ELMI information for interface Serial1
   IP Address used for Address Registration:9.2.7.9 My Ifindex:4
   ELMI AR status : Enabled.
   Connected to switch:hgw1 Platform:2611 Vendor:cisco 
   Sw side ELMI AR status: Enabled
   IP Address used by switch for address registration :9.2.6.9 Ifindex:5
   ELMI AR status : Enabled.
                (Time elapsed since last update 00:00:40)

The following is sample output from the show frame-relay qos-autosense command when ELMI and traffic shaping are enabled: 

Router# show frame-relay qos-autosense
 
 
ELMI information for interface Serial1 
 Connected to switch:FRSM-4T1   Platform:AXIS   Vendor:cisco
              (Time elapsed since last update 00:00:30)
 
 DLCI = 100
 OUT:   CIR  64000       BC 50000        BE 25000        FMIF 4497
 IN:    CIR  32000       BC 25000        BE 12500        FMIF 4497
 Priority 0     (Time elapsed since last update 00:00:12) 
 
 DLCI = 200
 OUT:   CIR 128000       BC 50000        BE 5100         FMIF 4497
 IN:    CIR Unknown      BC Unknown      BE Unknown      FMIF 4497
 Priority 0     (Time elapsed since last update 00:00:13)

The table below describes the significant fields in the output display.

Table 21 show frame-relay qos-autosense Field Descriptions

Field

Description

IP Address used for Address Registration

Management IP address of the data terminal equipment (DTE) interface.

My ifIndex

ifIndex of the DTE interface on which ELMI is running.

ELMI AR status

Indicates whether ELMI is enabled or disabled on the interface.

Connected to switch

Name of neighboring switch.

Platform

Platform information about neighboring switch.

Vendor

Vendor information about neighboring switch.

Sw side ELMI AR status

Indicates whether ELMI is enabled or disabled on the neighboring switch.

IP Address used by switch for address registration

IP address of DCE. If ELMI is not supported or is disabled, this value will be 0.0.0.0.

ifIndex

ifIndex of DCE.

DLCI

Value that indicates which PVC statistics are being reported.

Out:

Values reporting settings configured for the outgoing Committed Information Rate, Burst Size, Excess Burst Size, and FMIF.

In:

Values reporting settings configured for the incoming Committed Information Rate, Burst Size, Excess Burst Size, and FMIF.

Priority

Value indicating priority level (currently not used).

Related Commands

Command

Description

frame-relay qos-autosense

Enables ELMI on the Cisco router.

show frame-relay pvc

Displays statistics about PVCs for Frame Relay interfaces.

show frame-relay route

To display all configured Frame Relay routes, along with their status, use the show frame-relay route command in privileged EXEC mode.

show frame-relay route

Syntax Description

This command has no arguments or keywords.

Command Modes


Privileged EXEC

Command History

Release

Modification

10.0

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

Examples

The following is sample output from the show frame-relay route command: 

Router# show frame-relay route
    Input Intf      Input Dlci      Output Intf     Output Dlci  Status
    Serial1         100             Serial2         200          active
    Serial1         101             Serial2         201          active
    Serial1         102             Serial2         202          active
    Serial1         103             Serial3         203          inactive
    Serial2         200             Serial1         100          active
    Serial2         201             Serial1         101          active
    Serial2         202             Serial1         102          active
    Serial3         203             Serial1         103          inactive

The table below describes significant fields shown in the output.

Table 22 show frame-relay route Field Descriptions

Field

Description

Input Intf

Input interface and unit.

Input Dlci

Input DLCI number.

Output Intf

Output interface and unit.

Output Dlci

Output DLCI number.

Status

Status of the connection: active or inactive.

show frame-relay svc maplist

To display all the switched virtual circuits (SVCs) under a specified map list, use the show frame-relay svc maplist command in user EXEC or privileged EXEC mode.

show frame-relay svc maplist name

Syntax Description

name

Name of the map list.

Command Modes


User EXEC
Privileged EXEC

Command History

Release

Modification

11.2

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

Examples

The following example shows, first, the configuration of the map list “fish” and, second, the corresponding output of the show frame-relay svc maplist command. The following lines show the configuration: 

map-list fish local-addr X121 87654321 dest-addr X121 12345678
 ip 172.21.177.26 class fish ietf
 ipx 123.0000.0c07.d530 class fish ietf
!
map-class frame-relay fish
 frame-relay incir 192000
 frame-relay min-incir 19200
 frame-relay outcir 192000
 frame-relay min-outcir 19200
 frame-relay incbr(bytes) 15000
 frame-relay outcbr(bytes) 15000

The following lines show the output of the show frame-relay svc maplist command for the preceding configuration: 

Router# show frame-relay svc maplist fish
 
Map List : fish
Local Address : 87654321            Type: X121
Destination Address: 12345678       Type: X121
Protocol : ip 172.21.177.26
Protocol : ipx 123.0000.0c07.d530
Encapsulation : IETF
Call Reference : 1              DLCI : 501
Configured Frame Mode Information Field Size :
Incoming : 1500         Outgoing : 1500
Frame Mode Information Field Size :
Incoming : 1500         Outgoing : 1500
Configured Committed Information Rate (CIR) :
Incoming : 192 * (10**3)                Outgoing : 192 * (10**3)
Committed Information Rate (CIR) :
Incoming : 192 * (10**3)                Outgoing : 192 * (10**3)
Configured Minimum Acceptable CIR :
Incoming : 192 * (10**2)                Outgoing : 192 * (10**2)
Minimum Acceptable CIR :
Incoming : 0 * (10**0)          Outgoing : 0 * (10**0)
Configured Committed Burst Rate (bytes) :
Incoming : 15000                Outgoing : 15000
Committed Burst Rate (bytes) :
Incoming : 15000                Outgoing : 15000
Configured Excess Burst Rate (bytes) :
Incoming : 16000                Outgoing : 1200
Excess Burst Rate (bytes) :
Incoming : 16000                Outgoing : 1200

The table below describes significant fields in the output.

Table 23 show frame-relay svc maplist Field Descriptions

Field

Description

Map List

Name of the configured map-list.

Local Address...Type

Configured source address type (E.164 or X.121) for the call.

Destination Address...Type

Configured destination address type (E.164 or X.121) for the call.

Protocol : ip ... Protocol: ipx ...

Destination protocol addresses configured for the map-list.

Encapsulation

Configured encapsulation type (CISCO or IETF) for the specified destination protocol address.

Call Reference

Call identifier.

DLCI: 501

Number assigned by the switch as the DLCI for the call.

Configured Frame Mode Information Field Size: Incoming: Outgoing:

Frame Mode Information Field Size: Incoming: 1500 Outgoing: 1500

Lines that contrast the configured and actual frame mode information field size settings used for the calls.

Configured Committed Information Rate (CIR): Incoming: 192 * (10**3) Outgoing: 192 * (10**3)

Committed Information Rate (CIR): Incoming: 192 * (10**3) Outgoing: 192 * (10**3)

Lines that contrast the configured and actual committed information rate (CIR) settings used for the calls.

Configured Minimum Acceptable CIR: Incoming: 192 * (10**2) Outgoing: 192 * (10**2)

Minimum Acceptable CIR: Incoming: 0 * (10**0) Outgoing: 0 * (10**0)

Lines that contrast the configured and actual minimum acceptable CIR settings used for the calls.

Configured Committed Burst Rate (bytes): Incoming: 15000 Outgoing: 15000

Committed Burst Rate (bytes): Incoming: 15000 Outgoing: 15000

Lines that contrast the configured and actual committed burst rate (bytes) settings used for the calls.

Configured Excess Burst Rate (bytes): Incoming: 16000 Outgoing: 1200

Excess Burst Rate (bytes): Incoming: 16000 Outgoing: 1200

Lines that contrast the configured and actual excess burst rate (bytes) settings used for the calls.

Related Commands

Command

Description

class (map-list)

Associates a map class with a protocol-and-address combination.

frame-relay bc

Specifies the incoming or outgoing Bc for a Frame Relay VC.

frame-relay cir

Specifies the incoming or outgoing CIR for a Frame Relay VC.

frame-relay mincir

Specifies the minimum acceptable incoming or outgoing CIR for a Frame Relay VC.

map-class frame-relay

Specifies a map class to define QoS values for an SVC.

map-list

Specifies a map group and link it to a local E.164 or X.121 source address and a remote E.164 or X.121 destination address for Frame Relay SVCs.

show frame-relay traffic

To display the global Frame Relay statistics since the last reload, use the show frame-relay traffic command in privileged EXEC mode.

show frame-relay traffic

Syntax Description

This command has no arguments or keywords.

Command Modes


Privileged EXEC

Command History

Release

Modification

10.0

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

Examples

The following is sample output from the show frame-relay traffic command:

Router# show frame-relay traffic
Frame Relay statistics:
ARP requests sent 14, ARP replies sent 0
ARP request recvd 0, ARP replies recvd 10

show frame-relay vc-bundle

To display attributes and other information about a Frame Relay permanent virtual circuit (PVC) bundle, use the show frame-relay vc-bundle command in privileged EXEC mode.

show frame-relay vc-bundle vc-bundle-name [detail]

Syntax Description

vc-bundle-name

Name of this Frame Relay PVC bundle.

detail

(Optional) Displays output packet count information in addition to the other bundle member attributes for each PVC in the bundle specified by vc-bundle-name.

Command Modes


Privileged EXEC

Command History

Release

Modification

12.2(13)T

This command was introduced.

12.2(28)SB

This command was integrated into Cisco IOS Release 12.2(28)SB.

Usage Guidelines

Use this command to display packet service levels, bumping attributes, and other information about a specific Frame Relay PVC bundle. To view packet counts for each PVC in the bundle in addition to the other attributes, use the detail keyword.

Examples

Examples

The following example shows the Frame Relay PVC bundle named “MP-4-dynamic” with PVC protection applied. Note that in this PVC bundle, data-link connection identifier (DLCI) 400 is configured to explicitly bump traffic to the PVC that handles DSCP level 40, which is DLCI 404. All the other DLCIs are configured for implicit bumping. In addition, all the DLCIs are configured to accept bumped traffic.

The asterisk (*) before PVC 4a indicates that this PVC was configured with the precedence other command, which means the PVC will handle all levels that are not explicitly configured on other PVCs.

In this example all PVCs are up so, the values in the “Active level” fields match the values in the “Config level” fields. If a PVC goes down and its traffic is bumped, the “Active level” field value for the PVC that went down is cleared. The “Active level” field values for the PVC that the traffic bumped to will be updated to include the levels of the PVC that went down.

The first three PVCs in the following example make up a protected group. All three of these PVCs must go down before the bundle will go down. The last two PVCs are protected PVCs: if either of these PVCs goes down, the bundle will go down. 

Router# show frame-relay vc-bundle MP-4-dynamic
MP-4-dynamic on Serial1/4.1 - Status: UP Match-type: DSCP
Name 		DLCI 		Config. 	Active 				Bumping 			PG/ 		CIR 		Status 
				level 		level 			to/accept 			PV 		kbps
*4a 		400 		0-9 		0-9 			40/Yes 			pg 				up 
4b 		401 		10-19 		10-19 			9/Yes 			pg 				up 
4c 		402 		20-29 		20-29 			19/Yes 			pg 				up 
4d 		403 		30-39 		30-39 			29/Yes 			- 				up 
4e 		404 		40-49 		40-49 			39/Yes 			- 				up 
4f 		405 		50-59 		50-59 			49/Yes 			- 				up 
4g 		406 		60-62 		60-62 			59/Yes 			pv 				up 
4h 		407 		63 		63 			62/Yes 			pv 				up
Packets sent out on vc-bundle MP-4-dynamic : 0:
Router#

Examples

The following example shows that although some DLCIs are down, the bumping rules and the remaining DLCIs keep the bundle up and running for all traffic types.

Note that DLCI 304 is handling the traffic being bumped from the three DLCIs that are down. The “Active level” field indicates the levels that the PVC is actually handling, not just which levels are configured. 

Router# show frame-relay vc-bundle MP-3-static
MP-3-static on Serial1/4.1 - Status: UP Match-type: DSCP
Name 		DLCI 		Config. 	Active 				Bumping 			PG/ 		CIR 		Status 
				level 		level 			to/accept 			PV 		kbps
3a 		300 		0-9 		0-9 			-/Yes 			- 				up 
3b 		301 		10-19 		10-19 			9/Yes 			- 				up 
3c 		302 		20-29 		20-29 			19/Yes 			- 				up 
3d 		303 		30-39 					40/Yes 			- 				deleted 
3e 		304 		40-49 		30-59,63 			39/Yes 			- 				up 
3f 		305 		50-59 					49/Yes 			- 				deleted 
3g 		306 		60-62 		60-62 			59/No 			- 				up 
3h 		307 		63 					62/Yes 			- 				deleted
Packets sent out on vc-bundle MP-3-static : 335
Router#

Examples

The following example shows output for a PVC bundle configured with traffic shaping. The same rules of class inheritance apply to PVC-bundle members as to regular PVCs. 

Router# show frame-relay vc-bundle 26k
        
26k on Serial1/4.1 - Status:UP  Match-type:PRECEDENCE
Name    DLCI  Config.         Active          Bumping     PG/ CIR   Status
              level           level           to/ accept  PV  kbps
        521   0,2,4           0,2,4           -/Yes       -   20    up
        522   1,3,5-6         1,3,5-6         0/Yes       -   26    up
        523   7               7               6/Yes       -   20    up
Packets sent out on vc-bundle 26k :0
Router#

Examples

The following example shows the detail output of a PVC bundle. Note in this example that because all packet service levels are not handled, and because the PVCs are currently down, this bundle can never come up. 

Router# show frame-relay vc-bundle x41 detail
x41 on Serial1/1 - Status: DOWN Match-type: DSCP
Name 		DLCI 		Config. 		Active 			Bumping 			PG/ 		CIR 		Status 
				level 		level 			to/accept 			PV 		kbps
		410 		50-62 					49/Yes 			- 				down 
		411 		30,32,34,36,3.. 					29/Yes 			- 				down
Packets sent out on vc-bundle x41 : 0
Active configuration and statistics for each member PVC
DLCI 		Output pkts 				Active level
410 		0 				50-62 
411 		0 				30,32,34,36,38-40 
Router#

The table below describes the significant fields shown in the show frame-relay vc-bundle displays.

Table 24 show frame-relay vc-bundle Field Descriptions

Field

Description

Status:

PVC bundle status. Possible values are UP, DOWN, and INITIAL (no PVCs associated with the bundle).

Name

The user-defined, alphanumeric name of the PVC.

DLCI

The ID number of the PVC bundle member.

Config. level

The packet service levels configured for the PVC.

Active level

The packet service levels actually handled by the PVC. This may include packet service levels for bumped traffic accepted by the PVC.

Bumping to/accept

The packet service level that the PVC will bump to if it goes down/whether or not the PVC will accept bumped traffic from another PVC.

PG/PV

Indicates whether the PVC is a member of a protected group or is an individually protected PVC. A dash in this field indicates that the PVC is not protected.

CIR kbps

Committed information rate for the PVC, in kilobits per second.

Status

Indicates whether the PVC is up, down, or deleted.

Output pkts

Number of packets sent out on the PVC.

Related Commands

Command

Description

show frame-relay map

Displays the current Frame Relay map entries and information about the connections.

show frame-relay pvc

Displays statistics about PVCs for Frame Relay interfaces.

show l2cac

To display dynamic Layer 2 Call Admission Control (L2CAC) information for an asynchronous transfer mode (ATM) interface, use the show l2cac command in user EXEC or privileged EXEC mode.

show l2cac atm interface-number { aggregate-svc | vcd vcd-number }

Syntax Description

atm

Specifies an ATM interface.

interface-number

Interface or subinterface number. For more information about the numbering syntax for your networking device, use the question mark (?) online help function.

aggregate-svc

Aggregates switched virtual circuits (SVCs).

vcd

Specifies the virtual circuit descriptor (VCD) about which the L2CAC information must be displaced.

vcd-number

VCD number. The range is from 1 to 65535.

Command Modes


User EXEC (>)
Privileged EXEC (#)

Command History

Release

Modification

12.2(13)T

This command was introduced.

Examples

The following is sample output from the show l2cac command for aggregated SVCs on ATM interface 2/0: 

Router# show l2cac atm2/0 aggregate-sv
c 
*Jun 11 04:01:44.247: l2_cac_show_cmd. Begin
*Jun 11 04:01:44.247: l2_cac_show_cmd: l2 cac control block not found, with the vcd = 0
*Jun 11 04:01:44.247: l2_cac_show_cmd. End

The following is sample output from the show l2cac command for VCD 1 on ATM interface 2/0: 

Router# show l2cac atm2/0 vcd 1
 
vcci number = 1.
*Jun 11 04:02:16.487: l2_cac_show_cmd. Begin
*Jun 11 04:02:16.487: l2_cac_show_cmd: l2 cac control block not found, with the vcd = 1
*Jun 11 04:02:16.487: l2_cac_show_cmd. End

The table below describes the significant fields shown in the displays.

Table 25 show l2cac Field Descriptions

Field

Description

Begin

Indicates the beginning of the output.

l2 cac control block not found, with the vcd = 0

Displays the status of the L2CAC and the VCD number.

End

Indicates the end of the output.

vcci number

Displays the Virtual Circuit Connection Identifier (VCCI) number.

Related Commands

Command

Description

codec aal2-profile atmf

Configures the ATMF profile for VoAAL2.

show l2fib

To display information about a Layer 2 Forwarding Information Base (L2FIB), use the show l2fib command in privileged EXEC mode.

show l2fib { bridge-domain { summary | bridge-domain-ID [ port [ detail ] | detail | table { multicast | unicast } | address { multicast [ source-address ] group-address | unicast mac-address } | otv { decap | encap address } ] } | log { error | event } | output-list [ output-list-ID ] }

Syntax Description

bridge-domain

Displays the L2FIB bridge domain information.

summary

Displays summary information about a bridge domain.

bridge-domain-ID

ID of a bridge domain. The range is from 1 to 4096.

port detail

(Optional) Displays detailed information about the ports that are configured on a bridge domain.

detail

(Optional) Displays detailed information about the specified bridge domain.

table

(Optional) Displays the content of the specified bridge domain table.

multicast

Specifies the multicast address. This keyword is available only when the table keyword or the address keyword is configured.

unicast

Specifies the unicast address. This keyword is available only when the table keyword or the address keyword is configured.

address

(Optional) Displays information about a bridge domain address.

source-address

IPv4 source address. This argument is available only when the address multicast keyword is configured.

group-address

IPv4 group address or IPv4 multicast group prefix. This argument is available only when the address multicast keyword is configured.

mac-address

MAC address. This argument is available only when the address unicast keyword is configured.

otv

(Optional) Displays information about Overlay Transport Virtualization (OTV) tunnel adjacency.

decap

Displays information about OTV tunnel decapsulation adjacency. This argument is available only when the otv keyword is configured.

encap address

Displays information about OTV tunnel encapsulation adjacency for the specified encapsulated IPv4 address. This argument is available only when the otv keyword is configured.

log

Displays L2FIB logs.

error

Displays L2FIB error logs in the circular buffer.

event

Displays L2FIB event logs in the circular buffer.

output-list output-list-ID

Displays information about the specified output list.

Command Modes

Privileged EXEC (#)

Command History

Release

Modification

Cisco IOS XE Release 3.5S

This command was introduced.

Usage Guidelines

A bridge domain table consists of a unicast MAC address, a broadcast address, and IPv4 multicast entries.

Examples

The following is sample output from the show l2fib bridge-domain port command: 

Router# show l2fib bridge-domain 10 port

Bridge Domain: 10
  Replicator Port Count : 3
  Port Information : 
    Serv Inst: Te0/1/0:10, Refcount: 4
    Serv Inst: Ov1:10, Refcount: 4
    OTV Encap: 239.1.1.1, Refcount 2

The following is sample output from the show l2fib bridge-domain table command: 

Router# show l2fib bridge-domain 10 table unicast

Bridge Domain : 10
  Unicast Address table size : 3
  Unicast Address table information : 
    Mac: 0000.4817.1e7e, Adjacency: OTV Encap: 209.165.201.2
    Mac: 0000.4818.8a82, Adjacency: Serv Inst: Te0/1/0:10
    Mac: ffff.ffff.ffff, Adjacency: Olist: 2035, Ports: 2

The following is sample output from the show l2fib bridge-domain address command: 

Router# show l2fib bridge-domain 10 address unicast 1.1.2

Bridge Domain             : 10
Mac                       : 0001.0001.0002
Reference Count           : 1
Epoch                     : 0
Producer                  : BD-ENG
Flags                     : Age out
Adjacency: Service Instance: 
  ID                      : Te0/0/0:1
  Reference Count         : 3
  Bridge Domain           : 10
  Interface if num        : 3

The table below describes the significant fields shown in the display.

Table 26 show otv l2fib Field Descriptions

Field

Description

Bridge Domain

The ID of the bridge domain.

Replicator Port Count

Number of bridge domain ports.

Serv Inst

The service instance identifier.

Refcount

Number of references that exist for this adjacency.

OTV Encap

OTV encapsulation address.

Unicast Address table size

Number of MAC addresses in the bridge domain MAC address table.

Unicast Address table information

Details of MAC addresses in the bridge domain MAC address table.

Mac

MAC addresses of hosts in the site.

Adjacency

Adjacency or next hop.

Reference Count

Number of references that exist for this adjacency.

Epoch

The epoch number.

Producer

Producer of the route or next hop.

Flags

Attribute of the route or next hop.

Interface if num

The internal identifier of the interface.

Related Commands

Command

Description

show otv mroute

Displays the OTV multicast route information from the RIB.

show otv route

Displays the OTV MAC routes from the RIB.

show l2tun

To display general information about Layer 2 tunnels and sessions, use the show l2tuncommand in privileged EXEC mode.

show l2tun

Syntax Description

This command has no arguments or keywords.

Command Modes


Privileged EXEC

Command History

Release

Modification

12.0(23)S

This command was introduced.

12.3(2)T

This command was integrated into Cisco IOS Release 12.3(2)T.

12.2(25)S

This command was integrated into Cisco IOS Release 12.2(25)S.

12.2(27)SBC

Support for this command was integrated into Cisco IOS Release 12.2(27)SBC.

Usage Guidelines

The show l2tun command displays general information about all active Layer 2 tunnels and sessions. Use the show l2tun tunnel command or the show l2tun session command to display more detailed information about Layer 2 tunnels or sessions.

Examples

The following example shows the display of information about all currently active Layer 2 tunnels and sessions: 

Router# show l2tun
L2TP Tunnel and Session Information Total tunnels 1 sessions 1
LocID RemID Remote Name   State  Remote Address  Port  Sessions L2TP Class/
                                                                VPDN Group
45795 43092 PE1           est    10.1.1.1         0     1        generic
LocID      RemID      TunID      Username, Intf/      State  Last Chg Uniq ID
                                 Vcid, Circuit
42410      0          45795      123456789, Fa4/1/1   idle   00:00:24 1

The table below describes the significant fields shown in the display.

Table 27 show l2tun tunnel all Field Descriptions

Field

Description

Total tunnels

Total number of tunnels established on the router.

sessions

Total number of sessions established on the router.

LocID

Local ID of the tunnel.

RemID

Remote ID of the tunnel.

Remote Name

Hostname of the remote tunnel endpoint.

State

State of the tunnel.

Remote Address

IP address of the remote tunnel endpoint.

Port

Port number used by the remote tunnel endpoint.

Sessions

Number of sessions established in the tunnel.

L2TPclass

Name of the L2TP class the tunnel parameters are derived from.

VPDN group

Name of the virtual private dial-up network (VPDN) group the tunnel belongs to.

LocID

Local ID of the session.

RemID

Remote ID of the session.

TunID

Tunnel ID of the tunnel the session is in.

Username, Intf/Vcid, Circuit

The sessions username, interface, virtual circuit identifier (VCID), and circuit.

Last Chg

Time since the last change in the tunnel state, in hh:mm:ss.

Uniq ID

The tunnel session ID.

Related Commands

Command

Description

clear l2tun tunnel counters

Clears L2TP control channel authentication counters.

show l2tun session

Displays the current state of Layer 2 sessions and displays protocol information about L2TP control channels.

show l2tun tunnel

Displays the current state of a Layer 2 tunnel and displays information about currently configured tunnels.

show l2tun counters tunnel l2tp

To display global or per-tunnel control message statistics for Layer 2 Tunnel Protocol (L2TP) tunnels, use the show l2tun counters tunnel l2tp command in privileged EXEC mode.

show l2tun counters tunnel l2tp [ all | authentication | id local-id ]

Syntax Description

all

(Optional) Displays control message statistics for all L2TP tunnels that have per-tunnel statistics enabled.

authentication

(Optional) Displays global information about L2TP control channel authentication attribute-value (AV) pairs.

id local-id

(Optional) Displays control message statistics for the L2TP tunnel with the specified local ID.

Command Default

Global control message statistics are always enabled. Per-tunnel control message statistics are disabled by default.

Command Modes


Privileged EXEC

Command History

Release

Modification

12.2(28)SB

This command was introduced.

12.2(33)SRB

This command was integrated into Cisco IOS Release 12.2(33)SRB, and EXP ACK and CiscoACK were added to the command output.

Usage Guidelines

Use the show l2tun counters tunnel l2tpcommand to display global L2TP control message statistics.

Use the show l2tun counters tunnel l2tp authenticationcommand to display global L2TP authentication control message statistics.

The show l2tun counters tunnel l2tpcommand can display per-tunnel statistics, but per-tunnel statistics must first be enabled. Per-tunnel statistics are controlled on a tunnel by tunnel basis using the monitor l2tun counters tunnel l2tpcommand.

Use the show l2tun counters tunnel l2tp id local-idcommand to display per-tunnel statistics for a specific tunnel.

Use the show l2tun counters tunnel l2tp allcommand to display control message statistics for all tunnels that have per-tunnel statistics enabled.

Examples

The following example displays global L2TP control message counter information. In this example, the Number of unknown control messages received: displays only if the unknown message count is nonzero. 

Router# show l2tun counters tunnel l2tp
Global L2TP tunnel control message statistics:
 Number of unknown control messages received: 10
					XMIT      RE-XMIT         RCVD         DROP
			 	==========   ==========   ==========   ==========
Total                32           25           22           15
ZLB                   0            0            0            0
SCCRQ                 6           10            0            0
SCCRP                 0            0            1            0
SCCCN                 1            0            0            0
StopCCN               5            5            0            0
Hello                 0            0            0            0
OCRQ                  0            0            0            0
OCRP                  0            0            0            0
OCCN                  0            0            0            0
ICRQ                  2            0            0            0
ICRP                  0            0            2            0
ICCN                  2            0            0            0
CDN                   0            0            0            0
WEN                   0            0            0            0
SLI                   2            0            4            0
EXP ACK               0            0            0            0
SRRQ                  0            0            0            0
SRRP                  0            0            0            0
CiscoACK              4            0            5            5

The table below describes the significant fields shown in the display.

Table 28 show l2tun counters tunnel l2tp Field Descriptions

Field

Description

XMIT

The number of control messages that have been sent.

RE-XMIT

The number of control messages that have been sent.

RCVD

The number of control messages that have been received.

DROP

The number of control messages that have been dropped.

ZLB

The number of Zero Length Body (ZLB) messages.

SCCRQ

The number of Start-Control-Connection-Request (SCCRQ) messages.

SCCRP

The number of Start-Control-Connection-Reply (SCCRP) messages.

SCCCN

The number of Start-Control-Connection-Connected (SCCCN) messages.

StopCCN

The number of Stop-Control-Connection-Notification (StopCCN) messages.

Hello

The number of hello messages.

OCRQ

The number of Outgoing-Call-Request (OCRQ) messages.

OCRP

The number of Outgoing-Call-Reply (OCRP) messages.

OCCN

The number of Outgoing-Call-Connected (OCCN) messages.

ICRQ

The number of Incoming-Call-Request (ICRQ) messages.

ICRP

The number of Incoming-Call-Reply (ICRP) messages.

ICCN

The number of Incoming-Call-Connected (ICCN) messages.

CDN

The number of Call-Disconnect-Notify (CDN) messages.

WEN

The number of WAN-Error-Notify (WEN) messages.

SLI

The number of Set-Link-Info (SLI) messages.

EXP ACK

The number of Explicit-Acknowledgment (ACK) messages.

SRRQ

The number of Service Relay Request Message (SRRQ) messages.

SRRP

The number of Service Relay Reply Message (SRRP) messages.

CiscoACK

The number of Cisco Explicit-Acknowledgment (ACK) messages.

The following example shows the display of all possible L2TP control channel authentication AV pair statistics. AV pair statistic fields are displayed only if they are nonzero. For the purposes of this example, all possible output fields are displayed in the sample output. 

Router# show l2tun counters tunnel l2tp authentication
 L2TPv3 Tunnel Authentication Statistics:
   Nonce AVP Statistics:
     Ignored                                 0
     Missing                                 0
   All Digests Statistics:
     Unexpected                              0
     Unexpected ZLB                          0
   Primary Digest AVP Statistics:
     Validate fail                           0
     Hash invalid                            0
     Length invalid                          0
     Missing                                 0
     Ignored                                 0
     Passed                                  0
     Failed                                  0
   Secondary Digest AVP Statistics:
     Validate fail                           0
     Hash invalid                            0
     Length invalid                          0
     Missing                                 0
     Ignored                                 0
     Passed                                  0
     Failed                                  0
   Integrity Check Statistics:
     Validate fail                           0
     Length invalid                          0
     Passed                                  0
     Failed                                  0
   Local Secret Statistics:
     Missing                                 0
   Challenge AVP Statistics:
     Generate response fail                  0
     Ignored                                 0
   Challenge/Response AVP Statistics:
     Generate response fail                  0
     Missing                                 0
     Ignored                                 0
     Passed                                  0
     Failed                                  0
   Overall Statistics:
     Passed                                  0
     Skipped                                 0
     Ignored                                 0
     Failed                                  0

The table below describes the significant fields shown in the display.

Table 29 show l2tun counters tunnel l2tp authentication Field Descriptions

Field

Description

Nonce AVP Statistics

Counters for the nonce AV pair.

Ignored

Number of AV pair messages that were ignored.

Missing

Number of AV pair messages that were missing.

All Digests Statistics

Statistics for all configured digest passwords.

Unexpected

Digest information was received but the router is not configured for it.

Unexpected ZLB

A ZLB message was received while control message authentication is enabled. ZLB messages are permitted only when control message authentication is disabled.

Primary Digest AVP Statistics

Statistics for AV pair messages exchanged using the primary L2TP Version 3 (L2TPv3) control message digest password.

Validate fail

Number of AV pair messages that failed to validate.

Hash invalid

Number of AV pair messages with an invalid hash.

Length invalid

Number of AV pair messages with an invalid length.

Passed

Number of AV pair messages successfully exchanged.

Failed

Number of AV pair messages that have failed to authenticate.

Secondary Digest AVP Statistics

Statistics for AV pair messages exchanged using the secondary L2TPv3 control message digest password.

Integrity Check Statistics

Statistics for AV pair messages exchanged when integrity checking is enabled.

Local Secret Statistics

Statistics for AV pair messages related to the local secret.

Challenge AVP Statistics

Statistics for AV pair messages related to Challenge Handshake Authentication Protocol (CHAP) style authentication challenges.

Generate response fail

Number of AV pair messages that did not generate a response.

Challenge/Response AVP Statistics

Statistics for AV pair messages exchanged when CHAP-style authentication is configured.

Overall Statistics

Summary of the statistics for all authentication AV pair messages.

Skipped

The number of AV pair messages that authentication was not performed on.

The following example displays L2TP control message statistics for all L2TP tunnels with per-tunnel statistics enabled: 

Router# show l2tun counters tunnel l2tp all
Summary listing of per-tunnel statistics:
   LocID  RemID  Remote IP       Total     Total     Total     Total
                                 XMIT      RE-XMIT   RCVD      DROP      
   15587  39984  10.0.1.1       40        0         40        0         
   17981  42598  10.0.0.1       34        0         34        0         
   22380  14031  10.0.0.0       38        0         38        0         
   31567  56228  10.0.1.0       32        0         32        0         
   38360  30275  10.1.1.1       30        0         30        0         
   42759  1708   10.1.0.1       36        0         36        0         
Number of tunnels with per-tunnel stats: 6

The table below describes the significant fields shown in the display.

Table 30 show l2tun counters tunnel l2tp all Field Descriptions

Field

Description

LocID

The local tunnel ID.

RemID

The remote tunnel ID.

Remote IP

The IP address of the remote peer.

Total XMIT

Total number of control messages sent.

Total RE-XMIT

Total number of control messages sent.

Total RCVD

Total number of control messages received.

Total Drop

Total number of control messages dropped.

The following example enables per-tunnel L2TP control message statistics for the L2TP tunnel with the local ID 38360: 

Router# monitor l2tun counters tunnel l2tp id 38360 start
Router#

The following example displays L2TP control message statistics for the L2TP tunnel with the local ID 38360: 

Router# show l2tun counters tunnel l2tp id 38360
L2TP tunnel control message statistics:
   Tunnel LocID: 38360  RemID: 30275
   Remote Address: 10.1.1.1
					XMIT      RE-XMIT         RCVD         DROP
			 	==========   ==========   ==========   ==========
Total                32           25           22           15
ZLB                   0            0            0            0
SCCRQ                 6           10            0            0
SCCRP                 0            0            1            0
SCCCN                 1            0            0            0
StopCCN               5            5            0            0
Hello                 0            0            0            0
OCRQ                  0            0            0            0
OCRP                  0            0            0            0
OCCN                  0            0            0            0
ICRQ                  2            0            0            0
ICRP                  0            0            2            0
ICCN                  2            0            0            0
CDN                   0            0            0            0
WEN                   0            0            0            0
SLI                   2            0            4            0
EXP ACK               0            0            0            0
SRRQ                  0            0            0            0
SRRP                  0            0            0            0
CiscoACK              4            0            5            5

Related Commands

Command

Description

clear l2tun counters

Clears L2TP session counters.

clear l2tun counters tunnel l2tp

Clears global or per-tunnel control message statistics for L2TP tunnels.

monitor l2tun counters tunnel l2tp

Enables or disables the collection of per-tunnel control message statistics for L2TP tunnels.

show l2tun tunnel

Displays the current state of L2TP tunnels and information about configured tunnels.

show l2tun session

To display the current state of Layer 2 sessions and protocol information about Layer 2 Tunnel Protocol (L2TP) control channels, use the show l2tun session command in privileged EXEC mode.

show l2tun session [ l2tp | pptp ] [ all [filter] | brief [filter] [hostname] | circuit [filter] [hostname] | interworking [filter] [hostname] | packets [ipv6] [filter] | sequence [filter] | state [filter] ]

Syntax Description

l2tp

(Optional) Displays information about L2TP.

pptp

(Optional) Displays information about Point-to-Point Tunneling Protocol.

all

(Optional) Displays information about all current L2TP sessions on the router.

filter

(Optional) One of the filter parameters defined in the table below.

brief

(Optional) Displays information about all current L2TP sessions, including the peer ID address and circuit status of the L2TP sessions.

hostname

(Optional) Specifies that the peer hostname will be displayed in the output.

circuit

(Optional) Displays information about all current L2TP sessions, including circuit status (up or down).

interworking

(Optional) Displays information about Layer 2 Virtual Private Network (L2VPN) interworking.

packets

(Optional) Displays information about the packet counters (in and out) associated with current L2TP sessions.

ipv6

(Optional) Displays IPv6 packet and byte-count statistics.

sequence

(Optional) Displays sequencing information about each L2TP session, including the number of out-of-order and returned packets.

state

(Optional) Displays information about all current L2TP sessions and their protocol state, including remote Virtual Connection Identifiers (VCIDs).

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

12.0(23)S

This command was introduced.

12.3(2)T

This command was integrated into Cisco IOS Release 12.3(2)T.

12.2(25)S

This command was integrated into Cisco IOS Release 12.2(25)S.

12.0(31)S

The hostnamekeyword was added.

12.2(27)SBC

This command was integrated into Cisco IOS Release 12.2(27)SBC.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.4(11)T

This command was integrated into Cisco IOS Release 12.4(11)T.

12.2(33)SXH

This command was integrated into Cisco IOS Release 12.2(33)SXH.

12.4(22)T

This command was modified.The pptp and tunnel keywords were added.

Cisco IOS XE Release 2.6

The ipv6 keyword was added. The show l2tun session command with the all and l2tp all keywords was modified to display IPv6 counter information.

Usage Guidelines

Use the show l2tun sessioncommand to display information about current L2TP sessions on the router.

The table below defines the filter parameters available to refine the output of the show l2tun sessioncommand.

Table 31 Filter Parameters for the show l2tun session Command

Syntax

Description

ip-addr ip-address [vcid number]

Filters the output to display information about only those L2TP sessions associated with the IP address of the peer router. The 32-bit VCID shared between the peer router and the local router at each end of the control channel can be optionally specified.

  • ip-address --IP address of the peer router.

  • number --VCID number.

vcid number

Filters the output to display information about only those L2TP sessions associated with the VCID shared between the peer router and the local router at each end of the control channel.

  • number --VCID number.

username username

Filters the output to display information for only those sessions associated with the specified username.

  • username --Username.

tunnel {id local-tunnel local-session | remote-name remote-tunnel local-tunnel-name}

Displays the sessions in a tunnel.

  • id --Tunnel ID for established tunnels.

  • local-tunnel --Local tunnel ID.

  • local-session --Local session ID.

  • remote-name --Remote tunel name.

  • remote-tunnel --Remote tunnel name.

  • local-tunnel --Local tunnel name.

Examples

The following example shows how to display detailed information about all current L2TP sessions: 

Router# show l2tun session all
Session Information Total tunnels 0 sessions 1
Session id 42438 is down, tunnel id n/a
  Remote session id is 0, remote tunnel id n/a
Session Layer 2 circuit, type is Ethernet, name is FastEthernet4/1/1
  Session vcid is 123456789
  Circuit state is DOWN
    Local circuit state is DOWN
    Remote circuit state is DOWN
Call serial number is 1463700128
Remote tunnel name is PE1
  Internet address is 10.1.1.1
Local tunnel name is PE1
  Internet address is 10.1.1.2
IP protocol 115
  Session is L2TP signalled
  Session state is idle, time since change 00:00:26
    0 Packets sent, 0 received
    0 Bytes sent, 0 received
  Last clearing of "show vpdn" counters never
    Receive packets dropped:
      out-of-order:            0
      total:                   0
    Send packets dropped:
      exceeded session MTU:    0
      total:                   0
  DF bit off, ToS reflect disabled, ToS value 0, TTL value 255
  No session cookie information available
  UDP checksums are disabled
  L2-L2 switching enabled
  No FS cached header information available
  Sequencing is off
  Unique ID is 1

The following example shows how to display information only about the L2TP session set up on a peer router with an IP address of 192.0.2.0 and a VCID of 300: 

Router# show l2tun session all ip-addr 192.0.2.0 vcid 300
L2TP Session
Session id 32518 is up, tunnel id n/a
Call serial number is 2074900020
Remote tunnel name is tun1
  Internet address is 192.0.2.0
Session is L2TP signalled
  Session state is established, time since change 03:06:39
    9932 Packets sent, 9932 received
    1171954 Bytes sent, 1171918 received
  Session vcid is 300
  Session Layer 2 circuit, type is Ethernet Vlan, name is FastEthernet0/1/0.3:3
  Circuit state is UP
    Remote session id is 18819, remote tunnel id n/a
  Set DF bit to 0
  Session cookie information:
    local cookie, size 4 bytes, value CF DC 5B F3 
    remote cookie, size 4 bytes, value FE 33 56 C4 
  SSS switching enabled
  Sequencing is on
    Ns 9932, Nr 10001, 0 out of order packets discarded

The table below describes the significant fields shown in the displays.

Table 32 show l2tun session Field Descriptions

Field

Description

Total tunnels

Total number of L2TP tunnels established on the router.

sessions

Number of L2TP sessions established on the router.

Session id

Session ID for established sessions.

is

Session state.

tunnel id

Tunnel ID for established tunnels.

Remote session id

Session ID for the remote session.

tunnel id

Tunnel ID for the remote tunnel.

Session Layer 2 circuit, type is, name is

Type and name of the interface used for the Layer 2 circuit.

Session vcid is

VCID of the session.

Circuit state is

State of the Layer 2 circuit.

Local circuit state is

State of the local circuit.

Remote circuit state is

State of the remote circuit.

Call serial number is

Call serial number.

Remote tunnel name is

Name of the remote tunnel.

Internet address is

IP address of the remote tunnel.

Local tunnel name is

Name of the local tunnel.

Internet address is

IP address of the local tunnel.

IP protocol

The IP protocol used.

Session is

Signaling type for the session.

Session state is

Session state for the session.

time since change

Time since the session state last changed, in the format hh:mm:ss.

Packets sent, received

Number of packets sent and received since the session was established.

Bytes sent, received

Number of bytes sent and received since the session was established.

Last clearing of “show vpdn” counters

Time elapsed since the last clearing of the counters displayed with the show vpdn command. Time will be displayed in one of the following formats:

  • hh:mm:ss--Hours, minutes, and seconds.

  • dd:hh--Days and hours.

  • WwDd--Weeks and days, where W is the number of weeks and D is the number of days.

  • YyWw--Years and weeks, where Y is the number of years and W is the number of weeks.

  • never--The timer has not been started.

Receive packets dropped:

Number of received packets that were dropped since the session was established.

  • out-of-order--Total number of received packets that were dropped because they were out of order.

  • total--Total number of received packets that were dropped.

Send packets dropped:

Number of sent packets that were dropped since the session was established.

  • exceeded session MTU--Total number of sent packets that were dropped because the session maximum transmission unit (MTU) was exceeded.

  • total--Total number of sent packets that were dropped.

DF bit

Status of the Don’t Fragment (DF) bit option. The DF bit can be on or off.

ToS reflect

Status of the type of service (ToS) reflect option. ToS reflection can be enabled or disabled.

ToS value

Value of the ToS byte in the L2TP header.

TTL value

Value of the time-to-live (TTL) byte in the L2TP header.

local cookie

Size (in bytes) and value of the local cookie.

remote cookie

Size (in bytes) and value of the remote cookie.

UDP checksums are

Status of the User Datagram Protocol (UDP) checksum configuration.

switching

Status of switching.

No FS cached header information available

Fast Switching (FS) cached header information. If an FS header is configured, the encapsulation size and hexadecimal contents of the FS header will be displayed. The FS header is valid only for IP virtual private dialup network (VPDN) traffic from a tunnel server to a network access server (NAS).

Sequencing is

Status of sequencing. Sequencing can be on or off.

Ns

Sequence number for sending.

Nr

Sequence number for receiving.

Unique ID is

Global user ID correlator.

The following example shows how to display information about the circuit status of L2TP sessions on a router: 

Router# show l2tun session circuit
Session Information Total tunnels 3 sessions 3
LocID      TunID      Peer-address    Type Stat Username, Intf/                 
                                                Vcid, Circuit                   
32517      n/a 					 	172.16.184.142  VLAN UP   100, Fa0/1/0.1:1                
32519      n/a					 	172.16.184.142  VLAN UP   200, Fa0/1/0.2:2                
32518      n/a					 	172.16.184.142  VLAN UP   300, Fa0/1/0.3:3

The following example shows how to display information about the circuit status of L2TP sessions and the hostnames of remote peers: 

Router# show l2tun session circuit hostname

Session Information Total tunnels 3 sessions 3
LocID      TunID      Peer-hostname Type Stat Username, Intf/                 
                                                Vcid, Circuit                   
32517      n/a					 	<unknown>       VLAN UP   100, Fa0/1/0.1:1                
32519      n/a					 	router32        VLAN UP   200, Fa0/1/0.2:2                
32518      n/a					 	access3         VLAN UP   300, Fa0/1/0.3:3

The table below describes the significant fields shown in the displays.

Table 33 show l2tun session circuit Field Descriptions

Field

Description

LocID

Local session ID.

TunID

Tunnel ID.

Peer-address

IP address of the peer.

Peer-hostname

Hostname of the peer.

Type

Session type.

Stat

Session status.

Username, Intf/Vcid, Circuit

Username, interface name/VCID, and circuit number of the session.

Related Commands

Command

Description

show l2tun

Displays general information about Layer 2 tunnels and sessions.

show l2tun tunnel

Displays the current state of Layer 2 tunnels and information about configured tunnels.

show l2tun tunnel

To display the current state of Layer 2 Tunneling Protocol (L2TP) tunnels and information about configured tunnels, including local and remote hostnames, aggregate packet counts, and control channel information, use the show l2tun tunnel command in privileged EXEC mode.

show l2tun tunnel [ l2tp | pptp ] [ all [filter] | packets [filter] | state [filter] | summary [filter] | transport [filter] | authentication ]

Syntax Description

l2tp

(Optional) Displays information about L2TP.

pptp

(Optional) Displays information about Point-to-Point Tunneling Protocol.

all

(Optional) Displays information about all current L2TP tunnels configured on the router.

filter

(Optional) One of the filter parameters defined in the table below.

packets

(Optional) Displays aggregate packet counts for all negotiated L2TP sessions.

state

(Optional) Displays information about the current state of L2TP sessions, including the local and remote hostnames for each control channel.

summary

(Optional) Displays a summary of L2TP sessions on the router and their current state, including the number of virtual private dialup network (VPDN) sessions associated with each control channel.

transport

(Optional) Displays information about the L2TP control channels used in each session and the local and remote IP addresses at each end of the control channel.

authentication

(Optional) Displays global information about L2TP control channel authentication attribute-value pairs (AV pairs).

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

12.0(23)S

This command was introduced.

12.3(2)T

This command was integrated into Cisco IOS Release 12.3(2)T.

12.2(25)S

This command was integrated into Cisco IOS Release 12.2(25)S.

12.0(30)S

This command was enhanced to display information about pseudowire control channel authentication passwords.

12.0(31)S

The authentication keyword was added, and the output of the show l2tun tunnel all command was enhanced to display per-tunnel authentication failure counters.

12.2(27)SBC

This command was integrated into Cisco IOS Release 12.2(27)SBC.

12.2(28)SB

The authentication keyword was removed. The statistics previously displayed by the show l2tun tunnel authentication command are now displayed by the show l2tun counters tunnel l2tp authenticationcommand.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.4(11)T

This command was integrated into Cisco IOS Release 12.4(11)T.

12.2(33)SXH

This command was integrated into Cisco IOS Release 12.2(33)SXH.

12.4(22)T

This command was modified. The pptp keyword was added.

Cisco IOS XE Release 2.4

This command was integrated into Cisco IOS XE Release 2.4.

Usage Guidelines

Use the show l2tun tunnelcommand to display information about configured L2TP sessions on the router.

The table below defines the filter parameters available to refine the output of the show l2tun tunnelcommand.

Table 34 Filter Parameters for the show l2tun tunnel Command

Syntax

Description

id local-id

Filters the output to display information for only the tunnel with the specified local ID.

  • local-id --The local tunnel ID number. The range is 1 to 65535.

local-name local-name remote-name

Filters the output to display information for only the tunnel associated with the specified names.

  • local-name --Local tunnel name.

  • remote-name --Remote tunnel name.

remote-name remote-name local-name

Filters the output to display information for only the tunnel associated with the specified names.

  • remote-name --Remote tunnel name.

  • local-name --Local tunnel name.

Examples

The following example shows how to display detailed information about all L2TP tunnels: 

Router# show l2tun tunnel all
Tunnel Information Total tunnels 1 sessions 1
Tunnel id 26515 is up, remote id is 41814, 1 active sessions
  Tunnel state is established, time since change 03:11:50
  Tunnel transport is IP (115)
  Remote tunnel name is tun1
    Internet Address 172.0.0.0, port 0
  Local tunnel name is Router
    Internet Address 172.0.0.1, port 0
  Tunnel domain is 
  VPDN group for tunnel is 
  L2TP class for tunnel is
  0 packets sent, 0 received
  0 bytes sent, 0 received
  Control Ns 11507, Nr 11506
  Local RWS 2048 (default), Remote RWS 800
  Tunnel PMTU checking disabled
  Retransmission time 1, max 1 seconds
  Unsent queuesize 0, max 0
  Resend queuesize 1, max 1
  Total resends 0, ZLB ACKs sent 11505
  Total peer authentication failures 8 
  Current nosession queue check 0 of 5
  Retransmit time distribution: 0 0 0 0 0 0 0 0 0 
  Sessions disconnected due to lack of resources 0

The table below describes the significant fields shown in the displays.

Table 35 show l2tun tunnel all Field Descriptions

Field

Description

Total tunnels

Total number of L2TP tunnels currently established on the router.

sessions

Number of L2TP sessions currently established on the router.

Tunnel id is up

Tunnel ID and tunnel status.

remote id is

Remote ID.

active sessions

Number of active sessions.

Tunnel state is

State of the tunnel.

time since change

Time since the tunnel state last changed, in the format hh:mm:ss.

Tunnel transport is

Tunnel transport protocol.

Remote tunnel name is

Name of the remote tunnel endpoint.

Internet Address

IP address of the remote tunnel endpoint.

port

Port number used by the remote tunnel endpoint.

Local tunnel name is

Name of the local tunnel endpoint.

Internet Address

IP address of the local tunnel endpoint.

port

Port number used by the local tunnel endpoint.

Tunnel domain is

Domain information for the tunnel.

VPDN group for tunnel is

Name of the VPDN group associated with the tunnel.

L2TP class for tunnel is

Name of the L2TP class associated with the tunnel.

packets sent, received

Number of packets sent and received since the tunnel was established.

bytes sent, received

Number of bytes sent and received since the tunnel was established.

Control Ns, Nr

Sequence number for control packets sent and received.

Local RWS

Local receiving window size, in packets.

Remote RWS

Remote receiving window size, in packets.

Tunnel PMTU checking

Status of the tunnel path maximum transmission unit (MTU) checking option. It may be enabled or disabled.

Retransmission time, max

Current time, in seconds, required to resend a packet and maximum time, in seconds, that was required to resend a packet since tunnel establishment.

Unsent queuesize, max

Current size of the unsent queue and maximum size of the unsent queue since tunnel establishment.

Resend queuesize, max

Current size of the resend queue and maximum size of the resend queue since tunnel establishment.

Total resends

Total number of packets re-sent since tunnel establishment.

ZLB ACKs sent

Number of zero length body acknowledgment messages sent.

Total peer authentication failures

The total number of times peer authentication has failed.

Current nosession queue check

Number of tunnel timeout periods since the last session ended. Up to five tunnel timeouts are used if there are outstanding control packets on the unsent or resend queue. Otherwise, the tunnel is dropped after one tunnel timeout.

Retransmit time distribution

Histogram showing the number of retransmissions at 0, 1, 2,..., 8 seconds, respectively.

Sessions disconnected due to lack of resources

Number of sessions disconnected because of a lack of available resources.

secrets configured

The number of pseudowire control channel authentication passwords that are configured for the tunnel. One or two passwords may be configured.

The following example shows how to filter information to display L2TP control channel details only for the sessions configured with the local name Router and the remote name tun1: 

Router# show l2tun tunnel transport local-name Router tun1
Tunnel Information Total tunnels 3 sessions 3
LocID Type Prot  Local Address   Port  Remote Address  Port
26515 IP   115   172.16.0.0      0     172.16.0.1       0  
30866 IP   115   172.16.0.0      0     172.16.0.1       0

35217 IP 115 172.16.0.0 0 172.16.0.1 0 


 
		
 The table below describes the significant fields shown in the display.
		

 
		

Table 36 show l2tun tunnel transport Field Descriptions
 
				  
 Field
				  

 
						
 
				  
 Description
				  

 
						




 
				  
 Total tunnels
				  

 
						
 
				  
 Total number of tunnels established.
				  

 
						



 
				  
 sessions
				  

 
						
 
				  
 Number of sessions established.
				  

 
						



 
				  
 LocID
				  

 
						
 
				  
 Local session ID.
				  

 
						



 
				  
 Type
				  

 
						
 
				  
 Session type.
				  

 
						



 
				  
 Prot
				  

 
						
 
				  
 Protocol type used by the tunnel.
				  

 
						



 
				  
 Local Address
				  

 
						
 
				  
 IP address of the local tunnel endpoint.
				  

 
						



 
				  
 Port
				  

 
						
 
				  
 Port used by the local tunnel endpoint.
				  

 
						



 
				  
 Remote Address
				  

 
						
 
				  
 IP address of the remote tunnel endpoint.
				  

 
						



 
				  
 Port
				  

 
						
 
				  
 Port used by the remote tunnel endpoint.
				  

 
						







 
		
 The following example shows how to display information about the current state of L2TP tunnels with the local and remote hostnames of each session:
		

 
		
Router# show l2tun tunnel state
LocID  RemID   Local Name Remote Name  State  Last-Chg
26515  41814   Router      tun1         est     03:13:15
30866  6809    Router      tun1         est     03:13:15
35217  37340   Router      tun1         est     03:13:15


 
		
 The table below describes the significant fields shown in the display.
		

 
		

Table 37 show l2tun tunnel state Field Descriptions
 
				  
 Field
				  

 
						
 
				  
 Description
				  

 
						




 
				  
 LocID
				  

 
						
 
				  
 Local session ID.
				  

 
						



 
				  
 RemID
				  

 
						
 
				  
 Remote session ID.
				  

 
						



 
				  
 Local Name
				  

 
						
 
				  
 Name of the local tunnel endpoint.
				  

 
						



 
				  
 Remote Name
				  

 
						
 
				  
 Name of the remote tunnel endpoint.
				  

 
						



 
				  
 State
				  

 
						
 
				  
 Current state of the tunnel.
				  

 
						



 
				  
 Last-Chg
				  

 
						
 
				  
 Time since the state of the tunnel last changed, in the format hh:mm:ss.
				  

 
						







 
		
 The following example shows the display of all possible L2TP control channel authentication AV pair statistics. AV pair statistic fields are displayed only if they are nonzero. For the purposes of this example, all possible output fields are displayed in the sample output.
		

 
		
 This example is valid for Cisco IOS Release 12.0(31)S and later releases or Cisco IOS Release 12.2(27)SBC. To display authentication statistics in Cisco IOS Release 12.2(28)SB or a later release, use the 
		  monitor 
			 l2tun 
			 counters 
			 tun 
		  nel 
			 l2tp and 
			 show 
			 l2tun 
			 counters 
			 tunnel 
			 l2tp commands instead.
		

 
		
Router# show l2tun tunnel authentication
 L2TPv3 Tunnel Authentication Statistics:
   Nonce AVP Statistics:
     Ignored                                 0
     Missing                                 0
   All Digests Statistics:
     Unexpected                              0
     Unexpected ZLB                          0
   Primary Digest AVP Statistics:
     Validate fail                           0
     Hash invalid                            0
     Length invalid                          0
     Missing                                 0
     Ignored                                 0
     Passed                                  0
     Failed                                  0
   Secondary Digest AVP Statistics:
     Validate fail                           0
     Hash invalid                            0
     Length invalid                          0
     Missing                                 0
     Ignored                                 0
     Passed                                  0
     Failed                                  0
   Integrity Check Statistics:
     Validate fail                           0
     Length invalid                          0
     Passed                                  0
     Failed                                  0
   Local Secret Statistics:
     Missing                                 0
   Challenge AVP Statistics:
     Generate response fail                  0
     Ignored                                 0
   Challenge/Response AVP Statistics:
     Generate response fail                  0
     Missing                                 0
     Ignored                                 0
     Passed                                  0
     Failed                                  0
   Overall Statistics:
     Passed                                  0
     Skipped                                 0
     Ignored                                 0
     Failed                                  0


 
		
 The table below describes the significant fields shown in the display.
		

 
		

Table 38 show l2tun tunnel authentication Field Descriptions
 
				  
 Field
				  

 
						
 
				  
 Description
				  

 
						




 
				  
 Nonce AVP Statistics
				  

 
						
 
				  
 Counters for the nonce AV pair.
				  

 
						



 
				  
 Ignored
				  

 
						
 
				  
 Number of AV pair messages that were ignored.
				  

 
						



 
				  
 Missing
				  

 
						
 
				  
 Number of AV pair messages that were missing.
				  

 
						



 
				  
 All Digests Statistics
				  

 
						
 
				  
 Statistics for all configured digest passwords.
				  

 
						



 
				  
 Unexpected
				  

 
						
 
				  
 Digest information was received, but the router is not configured for it. 
				  

 
						



 
				  
 Unexpected ZLB
				  

 
						
 
				  
 A ZLB message was received while control message authentication was enabled. ZLB messages are permitted only when control message authentication is disabled.
				  

 
						



 
				  
 Primary Digest AVP Statistics
				  

 
						
 
				  
 Statistics for AV pair messages that were exchanged using the primary L2TP Version 3 (L2TPv3) control message digest password.
				  

 
						



 
				  
 Validate fail
				  

 
						
 
				  
 Number of AV pair messages that failed to validate.
				  

 
						



 
				  
 Hash invalid
				  

 
						
 
				  
 Number of AV pair messages with an invalid hash.
				  

 
						



 
				  
 Length invalid
				  

 
						
 
				  
 Number of AV pair messages with an invalid length.
				  

 
						



 
				  
 Passed
				  

 
						
 
				  
 Number of AV pair messages that were successfully exchanged.
				  

 
						



 
				  
 Failed
				  

 
						
 
				  
 Number of AV pair messages that failed to authenticate.
				  

 
						



 
				  
 Secondary Digest AVP Statistics
				  

 
						
 
				  
 Statistics for AV pair messages that were exchanged using the secondary L2TPv3 control message digest password. 
				  

 
						



 
				  
 Integrity Check Statistics
				  

 
						
 
				  
 Statistics for AV pair messages that were exchanged when integrity checking was enabled.
				  

 
						



 
				  
 Local Secret Statistics
				  

 
						
 
				  
 Statistics for AV pair that were messages related to the local secret.
				  

 
						



 
				  
 Challenge AVP Statistics
				  

 
						
 
				  
 Statistics for AV pair messages that were related to Challenge Handshake Authentication Protocol (CHAP), style authentication challenges.
				  

 
						



 
				  
 Generate response fail 
				  

 
						
 
				  
 Number of AV pair messages that did not generate a response.
				  

 
						



 
				  
 Challenge/Response AVP Statistics
				  

 
						
 
				  
 Statistics for AV pair messages exchanged when CHAP-style authentication is configured.
				  

 
						



 
				  
 Overall Statistics
				  

 
						
 
				  
 Summary of the statistics for all authentication AV pair messages.
				  

 
						



 
				  
 Skipped
				  

 
						
 
				  
 The number of AV pair messages that were not authenticated.
				  

 
						







 
	 


Related Commands
 
		

 
					 
 Command
					 

 
				  		
 
					 
 Description
					 

 
				  		




 
					 
 
						 
						  clear 
						  l2tun 
						  counters 
						  tunnel 
						  l2tp 
						 
					 

 
				  		
 
					 
 Clears global or per-tunnel control message statistics for L2TP tunnels.
					 

 
				  		



 
					 
 
						 
						  clear 
						  l2tun 
						  tunnel 
						  counters 
						 
					 

 
				  		
 
					 
 Clears L2TP control channel authentication counters.
					 

 
				  		



 
					 
 
						 
						  monitor 
						  l2tun 
						  counters 
						  tunnel 
						  l2tp 
						 
					 

 
				  		
 
					 
 Enables or disables the collection of per-tunnel control message statistics for L2TP tunnels.
					 

 
				  		



 
					 
 
						 
						  show 
						  l2tun 
						 
					 

 
				  		
 
					 
 Displays general information about Layer 2 tunnels and sessions.
					 

 
				  		



 
					 
 
						 
						  show 
						  l2tun 
						  session 
						 
					 

 
				  		
 
					 
 Displays the current state of Layer 2 sessions and protocol information about L2TP control channels.
					 

 
				  		



 
					 
 
						 
						  show 
						  l2tun 
						  counters 
						  tunnel 
						  l2tp 
						 
					 

 
				  		
 
					 
 Displays global or per-tunnel control message statistics for L2TP tunnels, or toggles the recording of per-tunnel statistics for a specific tunnel.
					 

 
				  		







 
		
 
		

 
	 






show l4f



      

To display the flow database for Layer 4 Forwarding (L4F), use the show l4f command in privileged EXEC mode.


    



      
show
l4f
 { clients | flows
 [ brief | detail | summary ]   | statistics } 

    


Syntax Description

      


                

                  
                    clients
                  
                


              		

                

Shows information about L4F clients.


              		




                

                  
                    flows
                  
                


              		

                

Shows information about L4F flows.


              		




                

                  
                    brief
                  
                


              		

                

(Optional) Shows brief information about L4F flows.


              		




                

                  
                    detail
                  
                


              		

                

(Optional) Shows detailed information about L4F flows.


              		




                

                  
                    summary
                  
                


              		

                

(Optional) Shows summary information about L4F flows.


              		




                

                  
                    statistics
                  
                


              		

                

Shows statistical information about L4F.


              		








    


Command Modes

      


Privileged EXEC (#)


    



      
Command History



                

Release


              		

                

Modification


              		





                

15.1(2)T


              		

                

This command was introduced.


              		








    


Usage Guidelines

      

Use this command to examine the flow database for L4F. New statistics for L4F are available through this command. The per-flow statistics help to correlate the information with existing per-TCB statistics. 


    


Examples

      

The following example displays the output of the show l4f statistics command. The fields in the table are self explanatory.


      
Router# show l4f statistics
L4F Global Statistics               Process     Interrupt
Client register                           4             0
Client deregister                         4             0
Client lookup failure                     8             0
Policy check accepted                     0             0
Policy check rejected                     0             0
Flows created                             0             0
Flow creation failed                      0             0
Flows destroyed                           0             0
Flows forced to bypass                    0             0
Flow lookup failed                        0             0
Flow cleanup scans                      501             0
Flows delayed for reinjection             0             0
Packet interception FORWARD               0             0
Packet interception PROXIED               0             0
Packet interception BYPASS                0             0
Packet interception ABORT                 0             0
Packet interception DROP                  0             0
Packet interception CONSUME               0             0
Packet interception PUNT                  0             0
Packet interception UNKNOWN               0             0
Packet interception forced punt           0             0
Spoofing to proxying failures             0             0
Spoofing to proxying success              0             0
Spoofing to proxying timeouts             0             0
Read notify called                        0             0
Read notify aborted                       0             0
Read notify punt                          0             0
Read notify ok                            0             0
Read buffer                               0             0
Read packet                               0             0
Write notify called                       0             0
Write notify aborted                      0             0
Write notify punt                         0             0
Write notify ok                           0             0
Write buffer                              0             0
Write packet                              0             0
Close notify called                       0             0
Shutdown called                           0             0
Close called                              0             0
Abort called                              0             0
Spoofing mode packets                     0             0
Proxying mode packets                     0             0
Packet reinject state alloc fail          0             0
Packet buffer alloc failed                0             0
Packet reinjection                        0             0
Packet reinjection punts                  0             0
Packet reinjection errors                 0             0
Packet reinjection other                  0             0
Packets delayed for reinjection           0             0
Packets drained from delay q              0             0
Packets freed from delay q                0             0



    


Related Commands

      


                

Command


              		

                

Description


              		





                

                  
                    debug
                    l4f
                  
                


              		

                

Enables troubleshooting for L4F flows.


              		








      

      


    






show line x121-address



      

To display all the line and rotary group addresses that are in a router, use the show line x121-addresscommand in user EXEC or privileged EXEC mode.


    



      
show
line
x121-address

    


Syntax Description

      

This command has no arguments or keywords.


    


Command Modes

      


User EXEC

Privileged EXEC


    



      
Command History



                

Release


              		

                

Modification


              		





                

12.3(11)YN


              		

                

This command was introduced.


              		




                

12.4(4)T


              		

                

This command was integrated into Cisco IOS Release 12.4(4)T.


              		








    


Usage Guidelines

      

You use this command to see whether any X.121 address has been assigned, and if so, to which line or rotary group it has been assigned.


    


Examples

      

The following example shows the lines and groups that have X.121 addresses. It also shows that address 1111 will be used as the calling address by calls originating from lines within Rotary Group 2.


      
Router# show line x121-address

	X121-Addresses     Line   Rotary
	34567 					97      	-
	12345 					98      	-
	23456 					-		1
	1111 					- 		2 (calling-address) 


      

Table 39 show line x121-address Field Descriptions

                

Field


              		

                

Description


              		





                

X121-Addresses


              		

                

X.121 address assigned to the TTY line or rotary group identified to the right in the same row.


              		




                

Line


              		

                

The TTY line’s absolute number.


              		




                

Rotary


              		

                

The rotary group’s ID number.


                

The words “calling address” also appear in this column when the group’s X.121 address has been assigned to be the source address for all calls originating with members of that group.


              		








    


Related Commands

      


                

Command


              		

                

Description


              		





                

                  
                    show
                    line
                  
                


              		

                

Displays status of configured lines.


              		








    






show mace metrics


 
		
 To display all Measurement, Aggregation, and Correlation Engine (MACE) metrics that were collected at the last export timeout, use the 
		  show 
			 mace 
			 metrics command in privileged EXEC mode.
		

 
	 


 
		
show
mace
metrics
 [ summary |  [name] 
monitor-name
 [ art | waas ]   | source-ip
 [ destination-ip
 [ port
 [protocol]  ]  ] 
 [ art | waas ]   ] 
 
	 


Syntax Description
 
		

 
					 
 
						 
						  summary 
						 
					 

 
				  		
 
					 
 (Optional) Displays the MACE metrics summary.
					 

 
				  		



 
					 
 
						 
						  name 
						 
					 

 
				  		
 
					 
 (Optional) Specifies the name of a flow monitor.
					 

 
				  		



 
					 
 
						 
						  monitor-name 
						 
					 

 
				  		
 
					 
 (Optional) Name of a flow monitor of type MACE that was previously configured.
					 

 
				  		



 
					 
 
						 
						  art 
						 
					 

 
				  		
 
					 
 (Optional) Displays the Application Response Time (ART) metrics.
					 

 
				  		



 
					 
 
						 
						  waas 
						 
					 

 
				  		
 
					 
 (Optional) Displays the Wide Area Application Services (WAAS) metrics.
					 

 
				  		



 
					 
 
						 
						  source-ip 
						 
					 

 
				  		
 
					 
 (Optional) Source IP address used by the exported packets. You can specify a valid source IP address, or you can use the 
						anykeyword. If you use the 
						anykeyword, the command displays information about all the source IP addresses.
					 

 
				  		



 
					 
 
						 
						  destination-ip 
						 
					 

 
				  		
 
					 
 (Optional) IP address of the destination host. You can specify a valid destination IP address or use the 
						anykeyword. If you use the 
						anykeyword, the command displays information about all the destination IP addresses.
					 

 
				  		



 
					 
 
						 
						  port 
						 
					 

 
				  		
 
					 
 (Optional) Destination port to which the exported packets are sent. The range is from 1 to 65535. You can specify a valid port address, or you can use the 
						anykeyword. If you use the 
						anykeyword, the command displays information about all the ports.
					 

 
				  		



 
					 
 
						 
						  protocol 
						 
					 

 
				  		
 
					 
 (Optional) Transport layer protocol used by the exported packets. The range is from 1 to 256. You can specify a valid protocol, or you can use the 
						anykeyword. If you use the 
						anykeyword, the command displays information about all the protocols.
					 

 
				  		







 
	 


Command Modes
 
		


Privileged EXEC (#)

 
	 


 
		
Command History


 
					 
 Release
					 

 
				  		
 
					 
 Modification
					 

 
				  		




 
					 
 15.1(4)M
					 

 
				  		
 
					 
 This command was introduced.
					 

 
				  		







 
	 


Usage Guidelines
 
		
 Use the 
		  show 
			 mace 
			 metrics command to display MACE metrics that are collected at the last export timeout. No metrics are displayed before the first export timeout. If you do not specify any source IP address, destination IP address, port, protocol, or flow-monitor, and instead use the 
		  any keyword, all MACE metrics for all flows are displayed.
		

 
	 


Examples
 
		
 The following examples are sample output from the 
		  show 
			 mace 
			 metrics command:
		

 
		
Router# show mace metrics summary
Segment          Client Pkts             Server Pkts             Flows Exported
0                 0                        0                        0             
1                 618                      771                      155           
2                 906                      890                      155           
4                 0                        0                        0             
8                 0                        0                        0             
16                182                      181                      46 


 
		
 The table below describes the significant fields shown in the display.
		

 
		

Table 40 show mace metrics summary Field Descriptions
 
				  
 Field 
				  

 
						
 
				  
 Description
				  

 
						




 
				  
 Segment
				  

 
						
 
				  
 WAAS Segment ID.
				  

 
						



 
				  
 Client Pkts
				  

 
						
 
				  
 Number of packets that are sent by the client.
				  

 
						



 
				  
 Server Pkts
				  

 
						
 
				  
 Number of packets that are sent by the server.
				  

 
						



 
				  
 Flows Exported
				  

 
						
 
				  
 Number of flows that are exported in the previous interval.
				  

 
						







 
		
Router# show mace metrics
Key fields:   | Client          | Server          | Dst. Port  | Protocol | Segment ID 
MACE Metrics: | DSCP        AppId      cByte       cPkts       sByte       sPkts      
ART Metrics:  | sumRT       sumAD       sumNT       sumCNT      sumSNT      sumTD                       sumTT       numT        sPkts       sByte       cPkts       cByte                       newSS       numR       
WAAS Metrics: | optMode    InBytes     OutBytes    LZByteIn    LZByteOut   DREByteIn                   DREByteOut 
Rec. 1    :   | 1.1.1.2         | 3.3.3.2         | 80         | 6        |  1          
MACE Metrics: | 0           0          88           4            72          2          
ART Metrics:  | 0           0           0           0            0           0           0                           0           2           0           4            0           0           0          
WAAS Metrics: | 7           0           0           0            0           0           0          
Rec. 2    :   | 1.1.1.2         | 3.3.3.2         | 80         | 6        |  2          
MACE Metrics: | 0           0          152          6            72          2          
ART Metrics:  | 0           0           0           0            0           0           0                           0           2           0           6            0           0           0          
WAAS Metrics: | 7           0           0           0            0           0           0 


 
		
 The table below describes the significant fields shown in the display.
		

 
		

Table 41 show mace metrics Field Descriptions
 
				  
 Field 
				  

 
						
 
				  
 Description
				  

 
						




 
				  
 Client
				  

 
						
 
				  
 Client address.
				  

 
						



 
				  
 Server
				  

 
						
 
				  
 Server address.
				  

 
						



 
				  
 Dst. Port
				  

 
						
 
				  
 Destination server port.
				  

 
						



 
				  
 Segment ID
				  

 
						
 
				  
 WAAS segment ID.
				  

 
						



 
				  
 DSCP
				  

 
						
 
				  
 Differentiated Services Code Point (DSCP) value in the Type of Service (TOS) field.
				  

 
						



 
				  
 AppId
				  

 
						
 
				  
 Network-Based Application Recognition (NBAR) application ID.
				  

 
						



 
				  
 cByte
				  

 
						
 
				  
 Client bytes.
				  

 
						



 
				  
 cPkts
				  

 
						
 
				  
 Client packets.
				  

 
						



 
				  
 sByte
				  

 
						
 
				  
 Server bytes.
				  

 
						



 
				  
 sPkts
				  

 
						
 
				  
 Server packets
				  

 
						



 
				  
 sumRT
				  

 
						
 
				  
 Response time sum.
				  

 
						



 
				  
 sumAD
				  

 
						
 
				  
 Application delay sum.
				  

 
						



 
				  
 sumNT
				  

 
						
 
				  
 Network time sum.
				  

 
						



 
				  
 sumCNT 
				  

 
						
 
				  
 Client network time sum.
				  

 
						



 
				  
 sumSNT
				  

 
						
 
				  
 Server network time sum.
				  

 
						



 
				  
 sumTD 
				  

 
						
 
				  
 Total delay sum.
				  

 
						



 
				  
 sumTT
				  

 
						
 
				  
 Transaction time sum.
				  

 
						



 
				  
 numT
				  

 
						
 
				  
 Number of transactions.
				  

 
						



 
				  
 newSS
				  

 
						
 
				  
 Number of sessions.
				  

 
						



 
				  
 numR
				  

 
						
 
				  
 Number of responses.
				  

 
						



 
				  
 optMode 
				  

 
						
 
				  
 WAAS optimization mode.
				  

 
						



 
				  
 InBytes
				  

 
						
 
				  
 WAAS input bytes.
				  

 
						



 
				  
 OutBytes
				  

 
						
 
				  
 WAAS output bytes.
				  

 
						



 
				  
 LZByteIn
				  

 
						
 
				  
 WAAS Lempel-Ziv (LZ) input bytes.
				  

 
						



 
				  
 LZByteOut
				  

 
						
 
				  
 WAAS LZ output bytes.
				  

 
						



 
				  
 DREByteIn 
				  

 
						
 
				  
 WAAS Data Redundancy Elimination (DRE) input bytes.
				  

 
						



 
				  
 DREByteOut 
				  

 
						
 
				  
 WAAS DRE output bytes.
				  

 
						







 
	 


Related Commands
 
		

 
					 
 Command
					 

 
				  		
 
					 
 Description
					 

 
				  		




 
					 
 
						 
						  flow 
						  monitor 
						  type 
						  mace 
						 
					 

 
				  		
 
					 
 Configures a Flexible NetFlow flow monitor of type MACE.
					 

 
				  		



 
					 
 
						 
						  mace 
						  enable 
						 
					 

 
				  		
 
					 
 Applies the global MACE policy on an interface.
					 

 
				  		



 
					 
 
						 
						  mace 
						  monitor 
						  waas 
						 
					 

 
				  		
 
					 
 Enables MACE on WAAS.
					 

 
				  		







 
	 






show mdns cache


 
		
  To display information about the resource records in the multicast Domain Name System (mDNS) cache, use the show 
			 mdns 
			 cache command in privileged EXEC mode.

 
	 


 
		
show
mdns
cache [
name | 
type] 

 
	 


Syntax Description
 
		

 
					 
 
						 
						  name 
						 
					 

 
				  		
 
					 
 (Optional)  Name of the resource record.

 
				  		



 type 



 (Optional)  Type of the mDNS cache resource record.









 
	 


Command Modes
 
		


Privileged EXEC (#)

 
	 


 
		
Command History


 
					 
 Release 
					 

 
				  		
 
					 
 Modification 
					 

 
				  		




15.3(2)S



This command was introduced.









 
	 


Usage Guidelines
 
		
 Use the     show 
			 mdns 
			 cache command to display resource record data for all mDNS service discovery devices. 
		This command lets you retrieve and resolve mDNS service discovery resource record information that is cached. The resource records belong to the Internet class are denoted by IN. 


This command displays information about the following types of resource records:

 
	 
  • Services Resolved (SRV) Records: Records where the instance name to hostname resolution is complete.
    

    • 

  • Point to Record (PTR) Records: Records listing all instances of the resource.
    

    • 

  • A Records: Records where the IPv4 address resolution is complete.
    

    • 

  • AAAA Records: Records where the IPv6 address resolution is complete.
    

    • 



This command also provides information about the Time to Live (TTL) value for each resource record. The TTL value denotes the time line for which the resource record can remain active in the cache.


The RR Record Data column displays miscellaneous information and notes about the resource records.




Examples
 
		
 The following is a sample output from the show 
			 mdns 
			 cache command. The fields in the output are self-explanatory.


Device# show mdns cache



                                                    MDNS CACHE
=========================================================================================================
[<NAME>]                               [<TYPE>] [<CLASS>] [<TTL>] [<RR Record Data>]


test._kwaas._tcp.local                     SRV     IN      117     0       0       5676    nostg-win7-1.local 

nostg-win7-1.local                         A       IN      117     1.1.1.6

_kwaas._tcp.local                          PTR     IN      4485    test._kwaas._tcp.local                     




 
		 
		 
		 
		 
		 
		 
		 
	 


Related Commands
 
		

 
					 
 Command 
					 

 
				  		
 
					 
 Description 
					 

 
				  		




 
						 
						  debug 
						  mdns 
						 
					 



 Enables debugging of mDNS service discovery information. 
					 





 
						show 
			 mdns 
			 requests 
					 



  Displays information about the browse requests, pending service requests, and pending host resolve requests recorded during the mDNS service discovery process.





 
					 
 
						show 
			 mdns 
			 statistics 
					 

 
				  		
 
					 
  Displays information about the number of packets sent, received, and dropped in the device recorded during the mDNS service discovery process.

 
				  		







 
		
 
		

 
	 






show mdns requests


 
		
  To display information about the  browse requests, pending service requests, and pending host resolve requests recorded during the multicast Domain Name System (mDNS) service discovery process, use the show 
			 mdns 
			 requests command in privileged EXEC mode.

 
	 


 
		
show
mdns
requests [
name | 
type] 

 
	 


Syntax Description
 
		

 
					 
 
						 
						  name 
						 
					 

 
				  		
 
					 
 (Optional)  Name of the mDNS request.

 
				  		



 type 



 (Optional)  Type of the mDNS service discovery request.









 
	 


Command Modes
 
		


Privileged EXEC (#)

 
	 


 
		
Command History


 
					 
 Release 
					 

 
				  		
 
					 
 Modification 
					 

 
				  		




15.3(2)S



This command was introduced.









 
	 


Usage Guidelines
 
		
 Use the show 
			 mdns 
			 requests command to display information about the different mDNS service discovery requests. 
		The different requests for which you can query, and later retrieve information about from the queue, are as follows:

 
	 
  • Browse Requests: Requests that are made for browsing through the other available devices to discover services of interest.
    

    • 

  • Service Requests: Requests made to other Cisco IOS devices that have been identified to contain services of interest.
    

    • 

  • Host Resolve Requests: Requests made to resolve the hostname to IPv4 and IPv6 addresses.
    

    • 





Examples
 
		
 The following is sample output from the show 
			 mdns 
			 requests command. The fields in the output are self-explanatory.


Device# show mdns requests



MDNS Outstanding Requests
======================================================
Request name  :   _kwaas._tcp.local
Request type  :   PTR
Request class :   IN
                     


 
		 
		 
		 
		 
		 
		 
		 
	 


Related Commands
 
		

 
					 
 Command 
					 

 
				  		
 
					 
 Description 
					 

 
				  		




 
						 
						  debug 
						  mdns 
						 
					 



 Enables debugging of mDNS service discovery information. 
					 





 
						show 
			 mdns 
			 cache 
					 



  Displays information about the resource records in the mDNS cache during the mDNS service discovery process.





 
					 
 
						show 
			 mdns 
			 statistics 
					 

 
				  		
 
					 
  Displays information about the number of packets sent, received, and dropped in the device during the mDNS service discovery process.

 
				  		







 
		
 
		

 
	 






show mdns statistics


 
		
  To display information about the  number of packets sent, received, and dropped in the device during the multicast Domain Name System (mDNS) service discovery process, use the show 
			 mdns 
			 statistics command in privileged EXEC mode.

 
	 


 
		
show
mdns
statistics
 
	 


Syntax Description
 
		
 This command has no arguments or keywords.

 
	 


Command Modes
 
		


Privileged EXEC (#)

 
	 


 
		
Command History


 
					 
 Release 
					 

 
				  		
 
					 
 Modification 
					 

 
				  		




15.3(2)S



This command was introduced.









 
	 


Examples
 
		
 The following is a sample output from the show 
			 mdns 
			 statistics command. The fields in the output are self-explanatory.


Device# show mdns cache


mDNS Statistics
mDNS packets sent     : 393
mDNS packets received : 1054
mDNS packets dropped  : 320
                  




 
		 
		 
		 
		 
		 
		 
		 
	 


Related Commands
 
		

 
					 
 Command 
					 

 
				  		
 
					 
 Description 
					 

 
				  		




 
						 
						  debug 
						  mdns 
						 
					 



 Enables debugging of mDNS service discovery information. 
					 





 
					 
 
						show 
			 mdns 
			 cache 
					 

 
				  		
 
					 
  Displays information about the resource records in the mDNS cache during the mDNS service discovery process.

 
				  		



 
					 
 
						show 
			 mdns 
			 requests 
					 

 
				  		
 
					 
  Displays information about the browse requests, pending service requests, and pending host resolve requests during the mDNS service discovery process.

 
				  		







 
		
 
		

 
	 






show mlrib common log


 
		
 To display the common Multilayer Routing Information Base (MLRIB) log buffers, use the 
		  show mlrib common log command in privileged EXEC mode. 
		

 
	 


 
		
 show mlrib common log
 { event | error } 
 [ all | unique | wrap ] 
 
	 


Syntax Description
 
		

 
					  
						 event 
						 
					  
				  


 
					 
 Displays common event logs. 
					 

 
				  		



 
					  
						 error 
						 
					  
				  


 
					 
 Displays common error logs. 
					 

 
				  		



 
					  
						 all 
						 
					  
				  


 
					 
 Displays all the buffers. 
					 

 
				  		



 
					  
						 unique 
						 
					  
				  


 
					 
 Displays unique entries in the buffer. 
					 

 
				  		



 
					  
						 wrap 
						 
					  
				  


 
					 
 Displays wrapped entries in the buffer. 
					 

 
				  		







 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 Cisco IOS XE Release 3.5S 
				  


 
					 
 This command was introduced. 
					 

 
				  		







 
	 


Examples
 
		
 The following is sample output from the 
		  show mlrib common log command: 
		

 
		
Router# show mlrib common log event all

[10/04/11 14:53:41.526 2 279] MLRIB_COMMON_REGISTRATION: client state set: L2FIB moving to REGISTERED state
[10/04/11 14:53:45.638 4 3] MLRIB_COMMON_REGISTRATION: client state set: ISISL2 OTV Overlay1 moving to REGISTERED state
[10/04/11 14:53:45.669 6 268] MLRIB_COMMON_REGISTRATION: client state set: IGMP Snoop moving to REGISTERED state
[10/04/11 14:53:47.063 7 245] MLRIB_COMMON_REGISTRATION: client state set: OTV APP UCAST PRODUCER moving to REGISTERED state

 
		
The table below describes the significant fields shown in the display. 
		

 
		

Table 42 show mlrib common log Field Descriptions
Field 
				



Description 
				






MLRIB_COMMON_REGISTRATION 
				



 
				





client state set 
				



 
				









 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 
 
						show otv mroute 
					 

 
				  		
 
					 
 Displays the OTV multicast route information from the RIB. 
					 

 
				  		



 
					 
 
						show otv route 
					 

 
				  		

Displays the OTV MAC routes from the RIB. 
				  









 
	 






show mlrib layer2 log


 
		
 To display the Layer 2-specific Multilayer Routing Information Base (MLRIB) log buffers, use the 
		  show mlrib layer2 log command in privileged EXEC mode. 
		

 
	 


 
		
 show mlrib layer2 log
 { event | error | trace } 
 [ all | unique | wrap ] 
 
	 


Syntax Description
 
		

 
					  
						 event 
						 
					  
				  


 
					 
 Displays Layer 2 event logs. 
					 

 
				  		



 
					  
						 error 
						 
					  
				  


 
					 
 Displays Layer 2 error logs. 
					 

 
				  		



 
					  
						 trace 
						 
					  
				  


 
					 
 Displays Layer 2 trace logs. 
					 

 
				  		



 
					  
						 all 
						 
					  
				  


 
					 
 Displays all the buffers. 
					 

 
				  		



 
					  
						 unique 
						 
					  
				  


 
					 
 Displays unique entries in the buffer. 
					 

 
				  		



 
					  
						 wrap 
						 
					  
				  


 
					 
 Displays wrapped entries in the buffer. 
					 

 
				  		







 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 Cisco IOS XE Release 3.5S 
				  


 
					 
 This command was introduced. 
					 

 
				  		







 
	 


Examples
 
		
 The following is sample output from the 
		  show mlrib layer2 log command: 
		

 
		
Router# show mlrib layer2 log event all

[10/17/11 10:44:38.889 E5D 167] MLRIB_L2_REDISTRIBUTE: hndl mcast redist refresh msg: Rcvd msg length 20, redist id = 0x0 walk id 0x0client = ISISL2 OTV Overlay1
[10/17/11 10:44:38.889 E5E 167] MLRIB_L2_REDISTRIBUTE: hndl mcast redist refresh msg: found filter for redist id = 0x0
[10/17/11 10:44:38.889 E5F 167] MLRIB_L2_REDISTRIBUTE: redist walk setup: for vpn 0x1 and client ISISL2 OTV Overlay1
[10/17/11 10:44:38.889 E60 167] MLRIB_L2_REDISTRIBUTE: snd redist walk resp msg: switch to hp msg ISISL2 OTV Overlay1 s=2 f=0x48 q=FALSE ri=0x0, wi=0x0
[10/17/11 10:44:38.960 E61 167] MLRIB_L2_REDISTRIBUTE: hndl mcast redist refresh msg: Rcvd msg length 28, redist id = 0x1 walk id 0x1client = OTV APP MCAST PRODUCER

 
		
The table below describes the significant fields shown in the display. 
		

 
		

Table 43 show mlrib common log Field Descriptions
Field 
				



Description 
				






MLRIB_L2_REDISTRIBUTE 
				



 
				





hndl mcast redist refresh msg 
				



 
				





Rcvd msg length 
				



 
				





redist id 
				



 
				





redist walk setup 
				



 
				





snd redist walk resp msg 
				



 
				









 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 
 
						show otv mroute 
					 

 
				  		
 
					 
 Displays the OTV multicast route information from the RIB. 
					 

 
				  		



 
					 
 
						show otv route 
					 

 
				  		

Displays the OTV MAC routes from the RIB. 
				  









 
	 






show mpls l2transport checkpoint




 
		
 To display checkpointing information about Any Transport over MPLS (AToM) virtual circuits (VCs), use the 
		  show mpls l2transport checkpoint command in privileged EXEC mode.
		

 
	 


 
		
show
mpls
l2transport
checkpoint
 
	 


Syntax Description
 
		
 This command has no arguments or keywords.
		

 
	 


Command Modes
 
		


Privileged EXEC (#)

 
	 


 
		
Command History


 
					 
 Release 
					 

 
				  		
 
					 
 Modification
					 

 
				  		




 
					 
 12.2(25)S
					 

 
				  		
 
					 
 This command was introduced.
					 

 
				  		



 
					 
 12.2(28)SB
					 

 
				  		
 
					 
 This command was integrated into Cisco IOS Release 12.2(28)SB.
					 

 
				  		



 
					 
 12.2SX
					 

 
				  		
 
					 
 This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.
					 

 
				  		



 
					 
 12.2(33)SRC
					 

 
				  		
 
					 
 This command was integrated into Cisco IOS Release 12.2(33)SRC.
					 

 
				  		



 
					 
 12.2(33)SCC
					 

 
				  		
 
					 
 This command was integrated into Cisco IOS Release 12.2(33)SCC.
					 

 
				  		







 
	 


Examples
 
		
 The output of the commands varies, depending on whether the output reflects the active or standby Route Processor (RP). 
		

 
		
 On the active RP, the command displays the following output:
		

 
		
Router# show mpls l2transport checkpoint
AToM Checkpoint info for active RP
Checkpointing is allowed
Bulk-sync checkpointed state for 1 VC


 
		
 On the standby RP, the command displays the following output:
		

 
		
Router# show mpls l2transport checkpoint
AToM HA Checkpoint info for standby RP
1 checkpoint information block in use


 
		
 In general, the output on the active RP shows that checkpointing information was sent to the backup RP. The output on the backup RP shows that checkpointing information was received from the active RP.
		

 
	 


Related Commands
 
		

 
					 
 Command 
					 

 
				  		
 
					 
 Description
					 

 
				  		




 
					 
 
						 
						  show mpls l2transport vc 
						 
					 

 
				  		
 
					 
 Displays information about the checkpointed data when checkpointing is enabled. 
					 

 
				  		







 
	 






show nve
	 interface




 
		
To display the
		  network virtualization endpoint (NVE) interface information, use the 
		  show nve
				interface command in privileged EXEC mode. 
		

 
	 


 
		
show nve
				  interface
nve-interface 
				
detail
 
	 


Syntax Description


 
				   
					 nve-interface 
				   
				
 
				  
The NVE
					 interface. 
				  

 
						



 
				   
					 detail 
				   
				
 
				  
(Optional)
					 Displays detailed information about the NVE interface. 
				  

 
						








Command Modes
 
		
EXEC (#)

 
	 


Command History


Release 
				
Modification 
				




 
				  
Cisco IOS
					 XE Release 3.11S 
				  

 
						
 
				  
This
					 command was introduced on the Cisco CSR 1000V. 
				  

 
						








Examples
 
		
The following
		  example shows the status of NVE interface 1: 
		

 
		
Router# show nve interface nve1
Interface: nve1, State:up, encapsulation:VXLAN 
source-interface: Lo1 (primary:1.1.1.1, secondary:1.1.1.2)

 
		
 
		

 
		
The following
		  example shows a detailed display for NVE interface 1: 
		

 
		
Router# show nve interface nve1 detail
Interface: nve1, State:up, encapsulation:VXLAN 
source-interface: Lo1 (primary:1.1.1.1, secondary:1.1.1.2)

VNI          mcast       VNI state
1010        239.0.0.0       UP
1110        239.0.0.0       UP

 
	 



Table 44 show nve
		interface Field Descriptions
 
				
Field 
				

 
			 		
 
				
Description 
				

 
			 		



 
				
VNI 
				

 
			 		
 
				
The VNI
				  number. 
				

 
			 		



 
				
mcast 
				

 
			 		
 
				
The
				  multicast address. 
				

 
			 		



 
				
VNI state 
				

 
			 		
 
				
The current
				  state of the VNI. 
				

 
			 		












show nve
	 peers




 
		
To display the
		  network virtualization endpoint (NVE) peers configured on the router, use the 
		  show nve
				peers command in EXEC mode. 
		

 
	 


 
		
show nve peers

 
	 


Command Modes
 
		
EXEC (#)

 
	 


Command History


Release 
				
Modification 
				




 
				  
Cisco IOS
					 XE Release 3.11S 
				  

 
						
 
				  
This
					 command was introduced on the Cisco CSR 1000V. 
				  

 
						








Examples
 
		
The following
		  example shows the NVE peers configured on the router: 
		

 
		
Router# show nve peers
Interface Peer-IP         VNI      Up Time
nve1       1.1.1.2        1010      10h
nve2       1.1.1.3        2030      20h

 
	 



Table 45 show nve peers
		Field Descriptions
 
				
Field 
				

 
			 		
 
				
Description 
				

 
			 		



 
				
Interface 
				

 
			 		
 
				
The NVE
				  interface. 
				

 
			 		



 
				
Peer-IP 
				

 
			 		
 
				
The peer IP
				  address of the NVE interface. 
				

 
			 		



 
				
VNI 
				

 
			 		
 
				
The VNI
				  number. 
				

 
			 		



 
				
Up Time 
				

 
			 		
 
				
The length
				  of time in hours that the NVE interface has been up. 
				

 
			 		












show nve
	 vni




 
		
To display the
		  network virtualization endpoint (NVE) VNIs configured on the router, use the 
		  show nve vni
		  command in EXEC mode. 
		

 
	 


 
		
show nve vni
 [ interfacenve-interface ] 
 
	 


Syntax Description


 
				   
					 interfacenve-interface 
				   
				
 
				  
(Optional)
					 Specifies the NVE interface. 
				  

 
						








Command Modes
 
		
EXEC (#)

 
	 


Command History


Release 
				
Modification 
				




 
				  
Cisco IOS
					 XE Release 3.11S 
				  

 
						
 
				  
This
					 command was introduced on the Cisco CSR 1000V. 
				  

 
						








Examples
 
		
The following
		  example displays all the NVE VNIs configured on the router: 
		

 
		
Router# show nve vni 
Interface  VNI          mcast       VNI state
nve1       1010        239.0.0.0      UP
nve2       1110        239.0.0.0      UP

 
		
 
		

 
		
The following
		  example displays the NVE VNIs assigned to NVE interface 1: 
		

 
		
Router# show nve vni interface nve1
Interface  VNI          mcast       VNI state
nve1       1010        239.0.0.0       UP
nve1       1110        239.0.0.0       UP

 
	 



Table 46 show nve vni
		Field Descriptions
 
				
Field 
				

 
			 		
 
				
Description 
				

 
			 		



 
				
Interface 
				

 
			 		
 
				
The NVE
				  interface. 
				

 
			 		



 
				
VNI 
				

 
			 		
 
				
The Virtual
				  Network Identifier. 
				

 
			 		



 
				
mcast 
				

 
			 		
 
				
The
				  multicast address for the NVE interface. 
				

 
			 		



 
				
VNI state 
				

 
			 		
 
				
The state of
				  the VNI. 
				

 
			 		












show otv


 
		
 To display the Overlay Transport Virtualization (OTV) status and parameters, use the 
		  show otv command in privileged EXEC mode. 
		

 
	 


 
		
 show otv
 [ overlay
overlay-interface ] 
 [detail] 
 
	 


Syntax Description
 
		

 
					  
						 overlay 
						overlay-interface 
						 
					  
				  


 
					 
 (Optional) Displays information about the specified overlay interface. The range is from 0 to 512. 
					 

 
				  		



 
					  
						 detail 
						 
					  
				  


 
					 
 (Optional) Displays detailed information about the overlay interface. 
					 

 
				  		







 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 
					 
Cisco IOS XE Release 3.5S 
					 

 
				  		
 
					 
 This command was introduced. 
					 

 
				  		







 
	 


Usage Guidelines
 
		
 If an overlay interface is specified, information about only that overlay is displayed; otherwise, information about all overlays is displayed.


In  a unicast-core network, the otv control-group and otv data-group commands are not configured. Therefore, fields displaying information about the control group and data group are not included in the output of the show otv in a unicast-core network.

 
	 


Examples
 
		
 The following example shows how to display OTV information about  a multicast-core network: 
		

 
		
Device# show otv overlay 1

Overlay Interface Overlay1
 VPN name                 : None
 VPN ID                   : 1
 State                    : UP
 AED Capable              : Yes
 IPv4 control group       : 224.0.0.1
 Mcast data group range(s): 239.0.0.1/8
 Join interface(s)        : GigabitEthernet 0/0/0
 Join IPv4 address        : 209.165.201.1
 Tunnel interface(s)      : Tunnel0
 Encapsulation format     : GRE/IPv4
 Site Bridge-Domain       : 100
 Capability               : Multicast-reachable
 Is Adjacency Server      : No
 Adj Server Configured    : No
 Prim/Sec Adj Svr(s)      : None

 
		
 The following is sample output from the show otv command in a unicast-core network when an OTV edge device is configured as a primary adjacency server: 
		

 
		
Device# show otv overlay 3

Overlay Interface Overlay3
 VPN name                 : otv_3
 VPN ID                   : 1
 State                    : UP
 AED Capable              : Yes
 Join interface(s)        : GigabitEthernet0/1/1
 Join IPv4 address        : 10.0.2.8
 Tunnel interface(s)      : Tunnel0
 Encapsulation format     : GRE/IPv4
 Site Bridge-Domain       : 2
 Capability               : Unicast-only
 Is Adjacency Server      : Yes
 Adj Server Configured    : No
 Prim/Sec Adj Svr(s)      : None


 The following is sample output from the show otv command in a unicast-core network when an OTV edge device is configured as a secondary adjacency server: 
		

 
		
Device# show otv overlay 3

Overlay Interface Overlay3
 VPN name                 : otv_3
 VPN ID                   : 1
 State                    : UP
 AED Capable              : Yes
 Join interface(s)        : GigabitEthernet0/3/3
 Join IPv4 address        : 172.16.1.8
 Tunnel interface(s)      : Tunnel0
 Encapsulation format     : GRE/IPv4
 Site Bridge-Domain       : 2
 Capability               : Unicast-only
 Is Adjacency Server      : Yes
 Adj Server Configured    : Yes
 Prim/Sec Adj Svr(s)      : 10.0.2.8


 The following is sample output from the show otv command when an OTV edge device is configured to use primary and secondary adjacency servers: 
		

 
		
Device# show otv overlay 3

Overlay Interface Overlay3
 VPN name                 : otv_3
 VPN ID                   : 1
 State                    : UP
 AED Capable              : Yes
 Join interface(s)        : GigabitEthernet0/1/1
 Join IPv4 address        : 192.168.1.5
 Tunnel interface(s)      : Tunnel1
 Encapsulation format     : GRE/IPv4
 Site Bridge-Domain       : 2
 Capability               : Unicast-only
 Is Adjacency Server      : No
 Adj Server Configured    : Yes
 Prim/Sec Adj Svr(s)      : 10.0.2.8/172.16.1.8


The table below describes the significant fields shown in the displays. 
		

 
		

Table 47 show otv Field Descriptions
Field 
				



Description 
				






VPN name 
				



 The OTV VPN name configured on the overlay interface. 
				





VPN ID 
				



 The ID allocated and used internally by Cisco IOS XE software. 
				





State 
				



The current state of the overlay interface. 
				





AED Capable 
				


 
				  
 Capability of the edge device to be authoritative for one or more VLANs. Valid values are Yes and No. Yes indicates that the edge device is capable of being authoritative for one or more VLANs. No indicates that the edge device is not capable of being authoritative, in which case, a reason is also displayed. 
				  

 
						



IPv4 control group 
				



 The IP multicast address used by OTV to form the overlay. 
				





Mcast data group range(s) 
				



 IP multicast addresses used for sending local IP multicast packets across the core. 
				





Join interface(s) 
				



 Interface used for sending Internet Group Management Protocol (IGMP) joins towards the core. 
				





Join IPv4 address 
				



 The IPv4 address of the join interface, used as the source IP address of OTV packets sent towards the core. 
				





Tunnel interface(s) 
				



 The tunnel interface automatically created by OTV to encapsulate and decapsulate OTV packets. 
				





Encapsulation format 
				



 The format of OTV packets sent across the core. 
				





Site Bridge-Domain 
				



 The ID of the bridge domain being used for internal site IS-IS peering. 
				





Capability 
				



 The multicast or unicast capability of the core. 
				





Is Adjacency Server 
				



Status indicating whether the local edge device is configured to be an adjacency server. 
				





Adj Server Configured 
				



 Status indicating whether this edge device is configured to use an adjacency server. 
				





Prim/Sec Adj Svr(s) 
				



 IP addresses of the primary and secondary adjacency servers configured, if any. 
				









 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 
 
						interface overlay 
					 

 
				  		
 
					 
 Creates an OTV overlay interface. 
					 

 
				  		



otv adjacency-server unicast-only
Configures a local edge device as an adjacency server in a unicast-core network.



otv control-group

Configures the IP multicast group address for the control and broadcast traffic for the specified OTV network.





otv data-group

Configures one or more ranges of core provider multicast group prefixes for multicast data traffic for the specified OTV network.





otv use-adjacency-server unicast-only

Configures a local edge device to use a remote adjacency server in a unicast-core network.





 
					 
 
						show otv isis 
					 

 
				  		
 
					 
 Displays the IS-IS status and configuration. 
					 

 
				  		







 
	 






show otv adjacency


 
		
 To display Overlay Transport Virtualization (OTV) adjacency information, use the 
		  show otv adjacency command in privileged EXEC mode. 
		

 
	 


 
		
 show otv
 [ overlay
overlay-interface ] 
adjacency
 
	 


Syntax Description
 
		

 
					  
						 overlay 
						overlay-interface 
						 
					  
				  


 
					 
 (Optional) Displays information about the specified overlay interface. The range is from 0 to 512. 
					 

 
				  		







 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 
					 
Cisco IOS XE Release 3.5S 
					 

 
				  		
 
					 
 This command was introduced. 
					 

 
				  		







 
	 


Usage Guidelines
 
		
 If an overlay interface is specified, information about only that overlay is displayed; otherwise information for all overlays is displayed. 
		

 
	 


Examples
 
		
 The following example shows how to display OTV adjacency information: 
		

 
		
Router# show otv overlay 1 adjacency

Overlay 1 Adjacency Database
Hostname       System-ID      Dest Addr       	Up Time   State
North          0026.cb0d.0800 209.165.201.13   0:37:10   UP

 
		
The table below describes the significant fields shown in the display. 
		

 
		

Table 48 show otv adjacency Field Descriptions
Field 
				



Description 
				






Hostname 
				



Dynamic hostname of the system. 
				





System-ID 
				



 The MAC address of the remote system. 
				





Dest Addr 
				



 The IP address of the remote edge device. 
				





Up Time 
				



Time since this adjacency has been up. 
				





State 
				



 Adjacency state of the neighboring interface. Valid states are Down, Init, and Up. 
				









 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 
 
						show otv isis 
					 

 
				  		
 
					 
 Displays the IS-IS status and configuration. 
					 

 
				  		







 
	 






show otv adjacency-server replication-list




 
		
 To display the list of unicast destinations for which multicast traffic is replicated, use the 
		  show otv adjacency-server replication-list command in privileged EXEC mode. 
		

 
	 


 
		
 show otv
 [ overlay
overlay-interface ] 
adjacency-server
replication-list
 
	 


Syntax Description
 
		

 
					  
						 overlay 
						overlay-interface 
						 
					  
				  


 
					 
 (Optional) Displays information about the specified overlay interface. The range is from 0 to 512. 
					 

 
				  		







 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 
					 
Cisco IOS XE Release 3.9S 
					 

 
				  		
 
					 
 This command was introduced. 
					 

 
				  		







 
	 


Usage Guidelines
 
		
 If an overlay interface is specified, information about only that overlay is displayed; otherwise, information about all overlays is displayed.


Overlay Transport Virtualization (OTV) maintains the unicast IP address of each remote edge device in the overlay network in a unicast replication list (URL). One URL is maintained per overlay network. OTV marks each address in the URL as active or inactive depending on the unicast-only status of the local and remote edge devices.

 
	 


Examples
 
		
 The following is sample output from the show otv adjacency-server replication-list command to display the list of unicast destinations for which multicast traffic is replicated: 
		

 
		
Device# show otv adjacency-server replication-list

Overlay 1 Unicast Replication List Database
Total num: 1

Dest Addr       Capability
10.10.10.2      Unicast

 
		
The table below describes the significant fields shown in the display. 
		

 
		

Table 49 show otv adjacency-server replication-list Field Descriptions
Field 
				



Description 
				






Dest Addr  
				



Specifies the IP address of the unicast destination.





Capability 
				



 Lists whether the destination is multicast- or unicast-capable.









 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 
 
						otv adjacency-server unicast-only 
					 

 
				  		
 
					 
Configures a local edge device as an adjacency server in a unicast-core network.

 
				  		



 
					 
 
						otv use-adjacency-server unicast-only 
					 

 
				  		
 
					 
Configures a local edge device to use a remote adjacency server in a unicast-core network.

 
				  		







 
	 






show otv arp-nd-cache


 
		
 To display Layer 2 and Layer 3 addresses cached from Address Resolution Protocol (ARP) packet inspection, use the 
		  show otv arp-nd-cache command in privileged EXEC mode. 
		

 
	 


 
		
 show otv
 [ overlay
overlay-interface ] 
arp-nd-cache
 
	 


Syntax Description
 
		

 
					  
						 overlay 
						overlay-interface 
						 
					  
				  


 
					 
 (Optional) Displays information about the specified overlay interface. The range is from 0 to 512. 
					 

 
				  		







 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 
					 
Cisco IOS XE Release 3.5S 
					 

 
				  		
 
					 
 This command was introduced. 
					 

 
				  		







 
	 


Usage Guidelines
 
		
 If an overlay interface is specified, cache entries for only that overlay are displayed. 
		

 
	 


Examples
 
		
 The following example shows how to display the Layer 2 and Layer 3 address mapping for remote MAC addresses: 
		

 
		
Router# show otv arp-nd-cache

Overlay1 ARP/ND L3->L2 Address Mapping Cache
 BD       MAC             Layer-3 Address  Age (HH:MM:SS)
 2        0030.19d2.ec39  172.16.1.2       00:05:30
 2        0030.16d5.3a5d  172.16.1.15      00:04:19
 65       0030.17e8.a389  172.16.1.18      00:00:50

 
		
The table below describes the significant fields shown in the display. 
		

 
		

Table 50 show otv arp-nd-cache Field Descriptions
Field 
				



Description 
				






BD 
				



 The ID of the bridge domain where the ARP cache entry was snooped. 
				





MAC 
				



 The MAC address snooped from the ARP reply packet. 
				





Layer-3 Address 
				



 The IP address snooped from the ARP reply packet. 
				





Age (HH:MM:SS) 
				



 Time since the ARP cache was last refreshed. 
				









 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 
 
						otv suppress arp-nd 
					 

 
				  		
 
					 
Suppresses sending the IPv4 ARP requests and IPv6 ND neighbor solicitations on an overlay network. 
					 

 
				  		



 
					 
 
						show otv isis 
					 

 
				  		
 
					 
 Displays the IS-IS status and configuration. 
					 

 
				  		







 
	 






show otv data-group


 
		
 To display Overlay Transport Virtualization (OTV) data group information, use the 
		  show otv data-group command in privileged EXEC mode. 
		

 
	 


 
		
 show otv
 [ overlay
overlay-interface ] 
data-group
 [ local | remote ] 
 [ detail ] 
 [ bridge-domain
bridge-domain-ID ] 
 [ delivery-source
delivery-source-address ] 
 [ delivery-group
delivery-group-address ] 
 [ instance
OTV-instance-ID ] 
 [ source
source-address ] 
 [ group
group-address ] 
 [ vlan
vlan-ID ] 
 
	 


Syntax Description
 
		

 
					  
						 overlay 
						overlay-interface 
						 
					  
				  


 
					 
 (Optional) Displays information about the specified overlay interface. The range is from 0 to 512. 
					 

 
				  		



 
						 local 
						 
					  
				  



(Optional) Displays output only for local data group sources. 
				  





 
						 remote 
						 
					  
				  



(Optional) Displays output only for remote data group sources. 
				  





 
						 detail 
						 
					  
				  



(Optional) Displays detailed output. 
				  





 
						bridge-domain 
						bridge-domain-ID 
					  
				  



(Optional) Filters output based on the specified bridge domain. The range is from 1 to 4096. 
				  





 
						delivery-source 
						delivery-source-address 
					  
				  



(Optional) Filters output based on the specified IPv4 delivery source address. 
				  





 
						delivery-group 
						delivery-group-address 
					  
				  



(Optional) Filters output based on the specified IPv4 delivery group address. 
				  





 
						instance 
						OTV-instance-ID 
				  



(Optional) Filters output based on the specified OTV instance. The range is from 0 to 127. 
				  





 
						source 
						source-address 
				  



(Optional) Filters output based on the specified IPv4 source address. 
				  





 
						group 
						group-address 
				  



(Optional) Filters output based on the specified IPv4 group address. 
				  





 
						vlan 
						vlan-ID 
				  



(Optional) Filters output based on the specified VLAN ID. The range is from 1 to 4094. 
				  









 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 
					 
Cisco IOS XE Release 3.5S 
					 

 
				  		
 
					 
 This command was introduced. 
					 

 
				  		







 
	 


Usage Guidelines
 
		
 If an overlay interface is specified, mappings for only that overlay are displayed. If the 
		  detail keyword is specified, then the number of unmapped sources is displayed. 
		

 
	 


Examples
 
		
 The following example shows how to display OTV data group information: 
		

 
		
Router# show otv data-group

Flags:  D - Local active source dynamically detected
        S - Local active source statically configured
        J - Data group has been joined in the core
        U - Data group has not been joined in the core

Remote Active Sources for Overlay1
 BD    Active-Source   Active-Group    Delivery-Source  Delivery-Group  Flags
 2     10.0.2.1        232.0.0.1       209.165.201.10   232.5.0.1       U
 4     10.0.4.1        232.0.0.1       209.165.201.10   232.5.0.3       U
 5     10.0.5.1        232.0.0.1       209.165.201.10   232.5.0.4       J
Displayed 3 remote data-group mappings

Local Active Sources for Overlay1
 BD    Active-Source   Active-Group    Delivery-Source  Delivery-Group  Flags
 1     10.0.1.1        232.0.0.1       209.165.201.10   232.5.0.0       S
 2     10.0.2.1        232.0.0.1       209.165.201.10   232.5.0.1       D


Displayed 2 local data-group mappings

 
		
The table below describes the significant fields shown in the display. 
		

 
		

Table 51 show otv data-group Field Descriptions
Field 
				



Description 
				






BD 
				



 The ID of the bridge domain where the multicast traffic was snooped. 
				





Active-Source 
				



 The unicast IP source address of the multicast sender. 
				





Active-Group 
				



 The multicast IP destination address used by the multicast sender. 
				





Delivery-Source 
				



 The unicast IP source address used for forwarding the multicast traffic in the core. 
				





Delivery-Group 
				



 The multicast IP destination address used for forwarding the multicast traffic in the core. 
				









 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 
 
						otv data-group 
					 

 
				  		
 
					 
Configures one or more ranges of core provider multicast group prefixes for multicast data traffic for the specified OTV network. 
					 

 
				  		



 
					 
 
						show otv isis 
					 

 
				  		
 
					 
 Displays the IS-IS status and configuration. 
					 

 
				  		







 
	 






show otv isis database



			
 To display the contents of the Overlay Transport Virtualization (OTV) Intermediate
				System-to-Intermediate System (IS-IS) link-state packet (LSP) database for each
				overlay, use the show otv isis database command in
				privileged EXEC mode. 


		



			
 show otv isis
 [ overlay
overlay-interface ] 
database
 [ mgroup | standard ] 
 [ detail | verbose ] 
lsp-ID

		


Syntax Description

			


										overlay overlay-interface
								



 (Optional) Displays information about the
									specified overlay interface. The range is from 0 to 512.
								






										 mgroup 
									
								



 (Optional) Displays the IS-IS multicast database for each
									overlay. 






										 standard 
									
								



(Optional) Displays standard LSP information. 






										 detail 
									
								



 (Optional) Displays detailed link state database IS-IS
									information. 






										 verbose 
									
								



(Optional) Displays verbose LSP information. 






									
										 lsp-ID 
									
								



								
 LSP ID in the form of xxxx.xxxx.xxxx.xx-xx or
											name.xx-xx. 


									








		


Command Modes

			
Privileged EXEC (#)


		



			
Command History


Release 



Modification 







								
Cisco IOS XE Release 3.5S 


									

								
This command was introduced. 


									








		


Usage Guidelines

			
The output of this command can be used to determine the unicast MACs and multicast
				groups received from each neighbor. 


		


Examples

			
 The following is sample output from the show otv isis
					database command: 


			
Router# show otv isis database detail

Tag Overlay1:
IS-IS Level-1 Link State Database:
LSPID      LSP Seq Num   LSP Checksum    LSP Holdtime   ATT/P/OL
u1.00-00   0x00000007    0x2B3A          1094           0/0/0
Area Address: 00
NLPID: 0xCC 0x8E
Hostname: u1
Layer 2 MAC Reachability: topoid 0, vlan 100, confidence 1
1122.3344.5566 2222.3344.5566
Layer 2 MAC Reachability: topoid 0, vlan 101, confidence 1
1122.7788.99aa 2222.7788.99aa


			
The table below describes the significant fields shown in the display. 


			

Table 52 show otv isis database detail
					Field Descriptions
Field 



Description 






LSPID 


LSP identifier. The first six octets form the
								system ID of the router that originated the LSP. The next octet is
								the pseudonode ID. When this byte is zero, the LSP describes links
								from the system. When it is nonzero, the LSP is a pseudonode LSP.
									
The last octet is the LSP number. If all data cannot fit into
									a single LSP, the LSP is divided into multiple LSP fragments.
									Each fragment has a different LSP number. 


									



LSP Seq Num 



 LSP sequence number that allows other systems
									to determine if they received the latest information from the
									source. 





LSP Checksum 



 Checksum of the entire LSP packet.
								





LSP Holdtime 



 Amount of time (in seconds) for which the LSP
									remains valid. An LSP hold time of zero indicates that this LSP
									was purged and is being removed from all routers’ link state
									databases (LSDBs). The value indicates how long the purged LSP
									will stay in the LSDB before it is completely removed.
								





ATT 



 Attach bit. This bit indicates that the router
									is also a Level 2 router and that it can reach other areas.
									Level 1 routers use the Attach bit to find the closest Level 2
									router. They install a default route to the closest Level 2
									router. 





P 



 P bit. This bit detects if the IS can repair
									area partitions. Cisco and other vendors do not support area
									partition repair. 





OL 



 Overload bit. This bit determines if the IS is
									congested. If the overload bit is set, other routers do not use
									this system as a transit router when they calculate routes. Only
									packets for destinations directly connected to the overloaded
									router are sent to this router. 





Area Address 



 Reachable area addresses from the router. For
									Level-1 LSPs, these are the area addresses configured manually
									on the originating router. For Level-2 LSPs, these are all the
									area addresses for the area to which this router belongs.
								





NLPID 



 Network Layer Protocol (NLP) identifier.
								





Hostname 



 Hostname of the node. 





Layer 2 MAC Reachability 



 Layer 2 MAC Reachability type, length, values
									(TLVs) and displays the MAC address that the IS is advertising,
									and the MAC address that can be reached from this IS.
								










		


Related Commands

			

Command 



Description 







								

									show otv isis
								


									

								
 Displays the IS-IS status and configuration. 


									








		






show otv isis hostname


 
		
 To display the Overlay Transport Virtualization (OTV) Intermediate System-to-Intermediate System (IS-IS) dynamic hostname table information, use the 
		  show otv isis hostname command in privileged EXEC mode. 
		

 
	 


 
		
 show otv isis
 [ overlay
overlay-interface ] 
hostname
 
	 


Syntax Description
 
		

 
						overlay 
						overlay-interface 
				  



 (Optional) Displays information about the specified overlay interface. The range is from 0 to 512. 
				  









 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 
					 
Cisco IOS XE Release 3.5S 
					 

 
				  		
 
					 
This command was introduced. 
					 

 
				  		







 
	 


Examples
 
		
 The following is sample output from the 
		  show otv isis hostname command: 
		

 
		
Router# show otv isis hostname

Level System ID        Dynamic Hostname (Overlay1)
1     AABB.CC00.0100   u1
*     AABB.CC00.0300   u3
1     AABB.CC00.0200   u2

 
		
 The dynamic hostname table in the example displays the router name-to-system ID mapping table entries for router u1, router u2, and the local router u3. The command output shows that the local router is running the IS-IS process named Overlay1. The table also shows that the neighbor routers u1 and u2 are Level-1 routers, and their hostnames are advertised by the Level-1 (L1) link-state packet (LSP). The * symbol that appears for the router u3 signifies that this is the router name-to-system ID mapping information for the local router. 
		

 
		
The table below describes the significant fields shown in the display. 
		

Table 53 show otv isis hostname detail Field Descriptions
Field 
				



Description 
				






Level 
				



 IS-IS level of the router. * indicates the local router. 
				





System ID 
				



 The MAC address of the remote edge device. 
				





Dynamic Hostname 
				



 The dynamic hostname of the edge device. 
				









 
		

 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 
 
						show otv isis 
					 

 
				  		
 
					 
 Displays the IS-IS status and configuration. 
					 

 
				  		







 
	 






show otv isis lsp-log


 
		
To display the Overlay Transport Virtualization (OTV) Intermediate System-to-Intermediate System (IS-IS) link-state packet (LSP) logs, use the 
		  show otv isis lsp-log command in privileged EXEC mode. 
		

 
	 


 
		
 show otv isis
 [ overlay
overlay-interface ] 
lsp-log 
				
 
	 


Syntax Description
 
		

 
						overlay 
						overlay-interface 
				  



 (Optional) Displays information about the specified overlay interface. The range is from 0 to 512. 
				  









 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 
					 
Cisco IOS XE Release 3.5S 
					 

 
				  		
 
					 
This command was introduced. 
					 

 
				  		







 
	 


Usage Guidelines
 
		
An entry in the LSP log is created each time a shortest path first (SPF) event is run along with a reason why SPF ran. 
		

 
	 


Examples
 
		
 The following is sample output from the 
		  show otv isis lsp-log command: 
		

 
		
Router# show otv isis lsp-log

Tag Overlay1:
Level 1 LSP log
When     Count Interface Triggers
00:47:11 3     Overlay1  CONFIG
00:46:58 2     Overlay1  NEWADJ DIS
00:45:44 1     Overlay1  CONFIG
00:44:58 1     Overlay1  CONFIG
00:21:51 4               CLEAR
00:20:49 4               CLEAR
00:20:46 4               CLEAR
00:19:01 2     Overlay1  DELADJ
00:18:45 2     Overlay1  NEWADJ DIS
00:18:06 4               CLEAR

Level 1 mgroup LSP log
When     Count Interface Triggers
00:47:11 2     Overlay1  CONFIG
00:45:44 1     Overlay1  CONFIG
00:44:58 1     Overlay1  CONFIG
00:18:45 2               CLEAR

 
		
The table below describes the significant fields shown in the display.
		

 
		

Table 54 show otv isis lsp-log detail Field Descriptions
Field 
				



Description 
				






When 
				



 Time elapsed (in hh:mm:ss) since the last LSP was generated. 
				





Count 
				



 Number of events that took place at this time. 
				





Interface 
				



 Interface that caused the LSP regeneration. 
				





Triggers 
				



 Event that triggered the LSP to be flooded. Possible triggers for an LSP are as follows: 
				  
  • AREASET—Active area set changed. 
					 
    

    • 

  • ATTACHFLAG—Attach bit changed state. 
					 
    

    • 

  • CLEAR—Some form of the manual 
						clear command was issued. 
					 
    

    • 

  • CONFIG—Any configuration change. 
					 
    

    • 

  • DELADJ—Adjacency went down. 
					 
    

    • 

  • DIS—Designated Intermediate System (DIS) or pseudonode changed. 
					 
    

    • 

  • ES—End System adjacency changed. 
					 
    

    • 

  • HIPPITY—LSP Database (LSPDB) overload bit changed state. 
					 
    

    • 

  • IF_DOWN—Needs a new LSP. 
					 
    

    • 

  • IP_DEF_ORIG—Default information originate changed. 
					 
    

    • 

  • IPDOWN—Directly connected IP prefix down. 
					 
    

    • 

  • IP_EXTERNAL—Redistributed IP route appeared or gone. 
					 
    

    • 

  • IPIA—Interarea IP route appeared or gone. 
					 
    

    • 

  • IPUP—Directly connected IP prefix up. 
					 
    

    • 

  • NEWADJ—New adjacency came up. 
					 
    

    • 

  • REDIST—Redistributed level-2 Connectionless Network Service (CLNS) route changed. 
					 
    

    • 

  • RRR_INFO—RRR bandwidth resource information. 
					 
    

    • 


 
				










	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 
 
						show otv isis 
					 

 
				  		
 
					 
 Displays the IS-IS status and configuration. 
					 

 
				  		







 
	 






show otv isis neighbors


To display the adjacencies formed by Overlay Transport Virtualization (OTV) Intermediate System-to-Intermediate System (IS-IS) for each overlay, use the 
		show otv isis neighbors command in privileged EXEC mode. 
	 


 
		
 show otv isis
 [  overlay
overlay-interface  | site ] 
neighbors
 [ detail ] 
 
	 


Syntax Description
 
		

 
						overlay 
						overlay-interface 
				  



 (Optional) Displays information about the specified overlay interface. The range is from 0 to 512. 
				  





 
						 site 
						 
					  
				  



(Optional) Configures the IS-IS Layer 2 site process. 
				  





 
					  
						 detail 
						 
					  
				  


 
					 
 (Optional) Displays detailed information about adjacencies. 
					 

 
				  		







 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 
					 
Cisco IOS XE Release 3.5S 
					 

 
				  		
 
					 
This command was introduced. 
					 

 
				  		







 
	 


Examples
 
		
 The following is sample output from the 
		  show otv isis neighbors command: 
		

 
		
Router# show otv isis neighbors

Tag Overlay1:
System Id   Type Interface  IP Address   						State   Holdtime   Circuit Id
u1          L1   Ov1        209.165.201.22     UP      22         u3.01

 
		
The table below describes the significant fields shown in the display. 
		

Table 55 show otv isis neighbors Field Descriptions
Field 
				



Description 
				






System Id 
				



 Six-byte value that identifies a system in an area. 
				





Type 
				



Level type. Indicates whether the IS-IS neighbor is a Level 1, Level-1-2, or Level 2 router. 
				





Interface 
				



 Interface from which the system was learned. 
				





IP Address 
				



 IP address of the neighbor router. 
				





State 
				



 Indicates whether the state of the IS-IS neighbor is up or down. 
				





Holdtime 
				



 Link-state packet (LSP) hold time. Amount of time (in seconds) for which the LSP remains valid. 
				





Circuit Id 
				



 Port location for the IS-IS neighbor router that indicates how it is connected to the local router. 
				









 
		

 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 
 
						show otv isis 
					 

 
				  		
 
					 
 Displays the IS-IS status and configuration. 
					 

 
				  		







 
	 






show otv isis nsf


 
		
To display the nonstop forwarding (NSF) state of Overlay Transport Virtualization (OTV) Intermediate System-to-Intermediate System (IS-IS), use the 
		  show otv isis nsf command in privileged EXEC mode. 
		

 
	 


 
		
 show otv isis nsf 
				
 
	 


Syntax Description
 
		
This command has no arguments or keywords. 
		

 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 
					 
Cisco IOS XE Release 3.5S 
					 

 
				  		
 
					 
This command was introduced. 
					 

 
				  		







 
	 


Examples
 
		
 The following is sample output from the 
		  show otv isis nsf command: 
		

 
		
Router# show otv isis nsf

Tag Overlay10:

NSF is ENABLED, mode 'cisco'

RP is ACTIVE, standby ready, RTR chkpt peer ready, UPD chkpt peer ready, bulk sync complete NSF interval timer expired (NSF restart enabled) Checkpointing enabled, no errors Local state: ACTIVE,  Peer state: STANDBY HOT,  Config Mode: SSO, Operating Mode: SSO

Tag Site:

NSF is ENABLED, mode 'cisco'

RP is ACTIVE, standby ready, RTR chkpt peer ready, UPD chkpt peer ready, bulk sync complete Checkpointing enabled, no errors Local state: ACTIVE,  Peer state: STANDBY HOT,  Config Mode: SSO, Operating Mode: SSO

 The output is self-explanatory. 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 
 
						show otv isis 
					 

 
				  		
 
					 
 Displays the IS-IS status and configuration. 
					 

 
				  		







 
	 






show otv isis protocol



			
 To display information about the general state of the Overlay Transport
				Virtualization (OTV) Intermediate-System-to-Intermediate System (IS-IS) process and
				a summary of the default configuration parameters, overlays, and interfaces enabled,
				use the show otv isis protocol command in privileged EXEC
				mode. 


		



			
 show otv isis
 [  overlay
overlay-interface  | site ] 
protocol

		


Syntax Description

			


										overlay overlay-interface
								



 (Optional) Displays information about the
									specified overlay interface. The range is from 0 to 512.
								






										 site 
									
								



(Optional) Configures the IS-IS Layer 2 site process.
								










		


Command Modes

			
Privileged EXEC (#)


		



			
Command History


Release 



Modification 







								
Cisco IOS XE Release 3.5S 


									

								
This command was introduced. 


									








		


Examples

			
 The following is sample output from the show otv isis
					protocol command: 


			
Router# show otv isis protocol

Tag Overlay10:
IS-IS Router: Overlay10
  System Id: AABB.CC00.8100.00  IS-Type: level-1
  Manual area address(es):
        00
  Routing for area address(es):
        00
  Interfaces supported by IS-IS:
        Overlay10

Tag Site:
IS-IS Router: Site
  System Id: AABB.CC00.8100.00  IS-Type: level-1
  Manual area address(es):
        00
  Routing for area address(es):
        00
  Interfaces supported by IS-IS:
        OTV-Site


			
The table below describes the significant fields shown in the display. 

Table 56 show otv isis protocol
						Field Descriptions
Field 



Description 






IS-IS Router 



Identifier of an IS-IS instance on the
										router. 





System Id 



 Identification value of the system.
									





Manual area address(es) 



 Area addresses that have been configured.
									





Routing for area address(es) 



 List of manually configured and learned
										area addresses. 





Interfaces supported by IS-IS 



 List of interfaces on the router
										supporting IS-IS. 










			


		


Related Commands

			

Command 



Description 







								

									show otv isis
								


									

								
 Displays the IS-IS status and configuration. 


									








		






show otv isis rib


To display information about the local Overlay Transport Virtualization (OTV) Intermediate System-to-Intermediate System (IS-IS) Routing Information Base (RIB), use the 
		show otv isis rib command in privileged EXEC mode. 
	 


 
		
 show otv isis rib
 [ overlay
overlay-interface ] 
 [ redistribution ] 
 { mac | multicast
 [mapping]   } 
 
	 


Syntax Description
 
		

 
						overlay 
						overlay-interface 
				  



 (Optional) Displays information about the specified overlay interface. The range is from 0 to 512. 
				  





 
					  
						 redistribution 
						 
					  
				  


 
					 
 (Optional) Displays IS-IS redistribution RIB information. 
					 

 
				  		



 
					  
						 mac 
						 
					  
				  


 
					 
 Displays MAC addresses from the IS-IS RIB. 
					 

 
				  		



 
						 multicast 
						 
					  
				  



Displays multicast route information from the IS-IS RIB. 
				  





 
						 mapping 
						 
					  
				  



(Optional) Displays multicast mapping information from the IS-IS RIB. 
				  









 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 
					 
Cisco IOS XE Release 3.5S 
					 

 
				  		
 
					 
This command was introduced. 
					 

 
				  		







 
	 


Examples
 
		
 The following is sample output from the 
		  show otv isis rib mac command: 
		

 
		
Router# show otv isis rib mac

Tag Overlay10:
 MAC  local rib for Overlay10 (Total 2)
  L2 Topology ID        Mac Address
  103                   1234.0002.0001
    [50/1] via 11.0.0.1(Overlay10), LSP[5/6]
  103                   1234.0002.0002
    [50/1] via 11.0.0.1(Overlay10), LSP[5/6]

 
		
 The following is sample output from the 
		  show otv isis rib multicast command: 
		

 
		
Router# show otv isis rib multicast

Tag Overlay10:
 MCAST  local rib for Overlay10 (Total Groups: 2, Sources: 4)
 L2 Topology ID    Source Address      Group Address
 103               192.0.1.1           224.0.0.1
    [50/1] via 192.0.2.1(Overlay10), LSP[6/6]
 103               192.0.2.1           224.0.0.1
    [50/1] via 192.0.2.1(Overlay10), LSP[6/6]
 103               192.0.1.1           224.0.0.2
    [50/1] via 192.0.2.1(Overlay10), LSP[6/6]
 103               192.0.2.1           224.0.0.2
    [50/1] via 192.0.2.1(Overlay10), LSP[6/6]

 
		
 The following is sample output from the 
		  show otv isis rib multicast mapping command: 
		

 
		
Router# show otv isis rib multicast mapping

Tag Overlay10:
 MCAST MAPPING   local rib for Overlay10 (Total Data/Delivery Groups: 4)
 Total Multicast Groups: 4, Sources: 4
 L2 Topology ID    Data Source     Data Group          Source          Group 
 103               192.0.2.1       232.1.1.2           192.0.1.1       224.0.0.1
    [0/0] LSP[6/6]
 103               192.0.2.1       232.1.1.3           192.0.2.1       224.0.0.1
    [0/0] LSP[6/6]
 103               192.0.2.1       232.1.1.6           192.0.1.1       224.0.0.2
    [0/0] LSP[6/6]
 103               192.0.2.1       232.1.1.7           192.0.2.1       224.0.0.2
    [0/0] LSP[6/6]

 
		
The table below describes the significant fields shown in the display. 
		

Table 57 show otv isis rib Field Descriptions
Field 
				



Description 
				






L2 Topology ID 
				



Layer 2 topology ID. 
				





Mac Address 
				



 Layer 2 route in the form of a unicast MAC Address. 
				





[50/1] 
				



 Administrative instance/type/metric for the routing path to reach the next hop of the router. 
				





via 192.0.2.1(Overlay10) 
				



 IP address of the next hop—in this instance, Overlay10. 
				





Source Address 
				



 Unicast source IP (or IPv6) address for a multicast Layer 2 route entry. 
				





Group Address 
				



 Multicast IP group address for a multicast Layer 2 route entry. 
				





Data Source 
				



 Unicast source IP (or IPv6) address in the provider network for a multicast mapping entry. 
				





Data Group 
				



Multicast IP group address in the provider network for a multicast mapping entry. 
				





Source 
				



Unicast source IP (or IPv6) address on the access side of the overlay for a multicast mapping entry. 
				





Group 
				



Multicast IP group address on the access side of the overlay for a multicast mapping entry. 
				









 
		

 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 
 
						show otv isis 
					 

 
				  		
 
					 
 Displays the IS-IS status and configuration. 
					 

 
				  		







 
	 






show otv isis spf-log


 
		
 To display logs related to Overlay Transport Virtualization (OTV) Intermediate-System-to-Intermediate System (IS-IS) shortest path first (SPF) computation, use the 
		  show otv isis spf-log command in privileged EXEC mode. 
		

 
	 


 
		
 show otv isis
 [ overlay
overlay-interface ] 
spf-log
 
	 


Syntax Description
 
		

 
						overlay 
						overlay-interface 
				  



 (Optional) Displays information about the specified overlay interface. The range is from 0 to 512. 
				  









 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 
					 
Cisco IOS XE Release 3.5S 
					 

 
				  		
 
					 
This command was introduced. 
					 

 
				  		







 
	 


Usage Guidelines
 
		
An entry in the log is created each time SPF is run, along with a reason why it ran. 
		

 
	 


Examples
 
		
 The following is sample output from the 
		  show otv isis spf-log command: 
		

 
		
Router# show otv isis spf-log

Tag Overlay1:
TID 0 level 1 SPF log
When     Duration   Nodes    Count    First trigger LSP    Triggers
00:17:05 0          1        3        u3.00-00             PERIODIC LSPEXPIRED
00:16:54 0          1        3        u3.00-00             NEWADJ NEWLSP CHGTUNNEL
00:16:53 0          2        1        u3.01-00             LSPEXPIRED
00:16:48 0          2        2        u1.00-00             LSPEXPIRED
00:16:47 0          3        3        u1.00-00             LSPEXPIRED
00:10:38 0          3        1        0000.0000.0000.00-00 LSPHEADER
00:02:06 1          3        1                             PERIODIC

 
		
The table below describes the significant fields shown in the display. 
		

Table 58 show otv isis spf-log Field Descriptions
Field 
				



Description 
				






When 
				



 The time elapsed (in hours: minutes: seconds) since the last full SPF calculation occurred. The last 20 occurrences are logged. 
				





Duration 
				



 Time (in milliseconds) required to complete this SPF run. Elapsed time is clock time, not CPU time. 
				





Nodes 
				



 Number of routers and pseudonodes (LANs) that comprise the topology calculated in this SPF run. 
				





Count 
				



 Number of events that triggered this SPF run. When there is a topology change, often multiple link-state packets (LSPs) are received in a short time. A router waits for 5 seconds before running a full SPF run, so it can include all new information. This count denotes the number of events (such as receiving new LSPs) that occurred while the router was waiting for 5 seconds before running full SPF. 
				





First trigger LSP 
				


 
				  
Whenever a full SPF calculation is triggered by the arrival of a new LSP, the router stores the LSP ID. The LSP ID can provide a clue as to the source of routing instability in an area. If multiple LSPs are causing an SPF run, only the LSP ID of the first received LSP is remembered. 
				  

 
						



Triggers 
				



 A possible reason that triggered a full SPF calculation. 
				









 
		

 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 
 
						show otv isis 
					 

 
				  		
 
					 
 Displays the IS-IS status and configuration. 
					 

 
				  		







 
	 






show otv isis vlan-database


 
		
To display information about Overlay Transport Virtualization (OTV) Intermediate System-to-Intermediate System (IS-IS) VLANs from the local database, use the 
		  show otv isis vlan-database command in privileged EXEC mode. 
		

 
	 


 
		
 show otv isis
 [ overlay
overlay-interface ] 
vlan-database 
				
 
	 


Syntax Description
 
		

 
						overlay 
						overlay-interface 
				  



 (Optional) Displays information about the specified overlay interface. The range is from 0 to 512. 
				  









 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 
					 
Cisco IOS XE Release 3.5S 
					 

 
				  		
 
					 
This command was introduced. 
					 

 
				  		







 
	 


Examples
 
		
 The following is sample output from the 
		  show otv isis vlan-database command. The fields shown in the output are self-explanatory.
		

 
		
Router# show otv isis vlan-database

Tag Overlay1:
OTV IS-IS process: Overlay1
VPN name: Overlay1
Bridge Domain ID  OTV Instance ID  VLAN ID  AED Status
1100              0                100      ENABLED
1101              0                101      ENABLED

 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 
 
						show otv isis 
					 

 
				  		
 
					 
 Displays the IS-IS status and configuration. 
					 

 
				  		







 
	 






show otv log


 
		
 To display the Overlay Transport Virtualization (OTV) debug log of events or errors, use the 
		  show otv log command in privileged EXEC mode. 
		

 
	 


 
		
 show otv log
 { event | error } 
 
	 


Syntax Description
 
		

 
					  
						 event 
						 
					  
				  


 
					 
 Displays the log of event buffers. 
					 

 
				  		



 
					  
						 error 
						 
					  
				  


 
					 
 Displays the log of error buffers. 
					 

 
				  		







 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 
					 
Cisco IOS XE Release 3.5S 
					 

 
				  		
 
					 
 This command was introduced. 
					 

 
				  		







 
	 


Examples
 
		
 The following example shows how to display the OTV log of events: 
		

 
		
Router# show otv log event

[1 11/12/10 20:04:23.630 3] OTV-APP-DB: otv-app Database initializing (Overlay table size = 4104 bytes (513 subblocks))
[2 11/12/10 20:04:23.630 3] OTV-APP-DB: Created otv_app subblock for overlay 1 VPN 1
[3 11/12/10 20:04:23.632 90] OTV-APP-EVC: Event: Walk topologies for VPN 0
3 entries printed

 
		
The table below describes the significant fields shown in the display. 
		

 
		

Table 59 show otv log Field Descriptions
Field 
				



Description 
				






OTV-APP-DB
				




				





OTV-APP-EVC
				




				










	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 
 
						interface overlay 
					 

 
				  		
 
					 
 Creates an OTV overlay interface. 
					 

 
				  		



 
					 
 
						show otv isis 
					 

 
				  		
 
					 
 Displays the IS-IS status and configuration. 
					 

 
				  		







 
	 






show otv mroute


 
		
 To display the Overlay Transport Virtualization (OTV) multicast route information from the Routing Information Base (RIB), use the 
		  show otv mroute command in privileged EXEC mode. 
		

 
	 


 
		
 show otv
 [ overlay
overlay-interface ] 
mroute
 [  bridge-domain
bridge-domain-ID  | vlan
vlan-ID  ] 
 [ source
source-address
group
group-address ] 
 
	 


Syntax Description
 
		

 
					  
						 overlay 
						overlay-interface 
						 
					  
				  


 
					 
 (Optional) Displays information about the specified overlay interface. The range is from 0 to 512. 
					 

 
				  		



 
						bridge-domain 
						bridge-domain-ID 
					  
				  



(Optional) Displays multicast routes for the specified bridge domain. The range is from 1 to 4096. 
				  





 
						vlan 
						vlan-ID 
				  



(Optional) Displays multicast routes for the specified VLAN. The range is from 1 to 4094. 
				  





 
						source 
						source-address 
				  



(Optional) Filters output based on the specified IPv4 source address. 
				  





 
						group 
						group-address 
				  



(Optional) Filters output based on the specified IPv4 group address. 
				  









 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 
					 
Cisco IOS XE Release 3.5S 
					 

 
				  		
 
					 
 This command was introduced. 
					 

 
				  		







 
	 


Examples
 
		
 The following example shows how to display multicast route information from the RIB: 
		

 
		
Router# show otv mroute bridge-domain 289 

OTV Multicast MAC Routing Table for Overlay1
Bridge-Domain = 289, s = 198.51.100.100, g = 232.1.1.20/8
 Incoming interface list:
  Overlay1, 198.51.100.100
 Outgoing interface list:
  Service Instance ID 50, GigabitEthernet 0/0/1
  Overlay1, 198.51.100.100
 Incoming interface count = 1, Outgoing interface count = 2

Bridge-Domain = 289, s = 198.51.100.101, g = 232.1.1.21/8
 Incoming interface list:
  Overlay1, 198.51.100.101
 Outgoing interface list:
  Service Instance ID 50, GigabitEthernet 0/0/1
  Overlay1, 198.51.100.101
 Incoming interface count = 1, Outgoing interface count = 2


2 multicast routes displayed in Overlay1

 
		
The table below describes the significant fields shown in the display. 
		

 
		

Table 60 show otv mroute Field Descriptions
Field 
				



Description 
				






Bridge-Domain 
				



 The ID of the bridge domain where the multicast route was learned. 
				





s 
				



 Source IPv4 address. 
				





g 
				



 Group IPv4 address 
				





Incoming interface list 
				



 The interface or Ethernet service instance where multicast packets are received. 
				





Outgoing interface list 
				



 Interfaces or Ethernet service instances where multicast packets will be forwarded. 
				









 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 
 
						show otv isis 
					 

 
				  		
 
					 
 Displays the IS-IS status and configuration. 
					 

 
				  		







 
	 






show otv route


 
		
 To display Overlay Transport Virtualization (OTV) MAC routes from the Routing Information Base (RIB), use the 
		  show otv route command in privileged EXEC mode. 
		

 
	 


 
		
 show otv
 [ overlay
overlay-interface ] 
route
 [ neighbor-address
neighbor-address ] 
 [  bridge-domain
bridge-domain-ID  | vlan
vlan-ID  ] 
 [ mac-address ] 
 [ owner
 { bd-engine | isis | otv }  ] 
 
	 


Syntax Description
 
		

 
					  
						 overlay 
						overlay-interface 
						 
					  
				  


 
					 
 (Optional) Displays information about the specified overlay interface. The range is from 0 to 512. 
					 

 
				  		



 
					  
						neighbor-address 
						neighbor-address 
					  
				  



(Optional) Filters output based on the specified IPv4 address of the neighbor. 
				  





 
						bridge-domain 
						bridge-domain-ID 
					  
				  



(Optional) Displays unicast routes for the specified bridge domain. The range is from 1 to 4096. 
				  





 
						 vlan 
						vlan-ID 
					  
				  



(Optional) Displays unicast routes for the specified VLAN. The range is from 1 to 4094. 
				  





mac-address 
				  



(Optional) Filters output to display routes for the specified MAC address.
				  





 
						 owner 
						 
					  
				  



(Optional) Filters output based on the specified owner. 
				  





 
						 bd-engine 
						 
					  
				  



Displays unicast MAC routes added by the BD-Engine. This keyword is available only when the 
					 owner keyword is configured. 
				  





 
						 isis 
						 
					  
				  



Displays unicast MAC routes added by Intermediate System-to-Intermediate System (IS-IS). This keyword is available only when the 
					 owner keyword is configured. 
				  





 
						 otv 
						 
					  
				  



Displays unicast MAC routes added by OTV. This keyword is available only when the 
					 owner keyword is configured. 
				  









 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 
					 
Cisco IOS XE Release 3.5S 
					 

 
				  		
 
					 
 This command was introduced. 
					 

 
				  		







 
	 


Examples
 
		
 The following example shows how to display OTV MAC route information: 
		

 
		
Router# show otv route

Codes: BD - Bridge-Domain, AD - Admin-Distance, SI - Service Instance
OTV Unicast MAC Routing Table for Overlay1
Inst VLAN BD     MAC Address    AD    Owner  Next Hops(s)
----------------------------------------------------------
0    67   67     0007.0007.0009 20    OTV    232.1.2.3
0    67   67     0102.0304.0506 40    BD Eng Gi0/0/1:SI67
0    99   99     0009.0009.0009 20    OTV    232.1.2.3
0    99   99     0038.0000.0000 1     OTV    Ov3, 10.33.1.0
0    99   99     0039.0000.0000 1     OTV    Ov3, 10.34.5.2
0    99   99     003a.0000.0000 1     OTV    Ov3, 10.35.4.6
0    99   99     003b.0000.0000 1     OTV    Ov3, 10.36.3.0
0    99   99     0102.0304.0507 40    BD Eng Et0/1:SI99

8 unicast routes displayed in Overlay1

OTV Unicast MAC Routing Table for Overlay2
Inst VLAN BD     MAC Address    AD    Owner  Next Hops(s)
----------------------------------------------------------
0    57   57     0005.0007.0009 20    OTV    Flood
0    57   57     0102.0304.0506 40    BD Eng Gi0/0/0:SI57
0    57   57     0102.0304.0508 40    BD Eng Gi0/0/0:SI57
0    57   57     0102.0304.0509 40    BD Eng Gi0/0/0:SI57
0    59   59     0005.0009.0009 20    OTV    Flood
0    59   59     0102.0304.0507 40    BD Eng Gi0/0/0:SI59

6 unicast routes displayed in Overlay2

OTV Unicast MAC Routing Table for Overlay3
Inst VLAN BD     MAC Address    AD    Owner  Next Hops(s)
----------------------------------------------------------

0 unicast routes displayed in Overlay3

----------------------------------------------------------
14 Total Unicast Routes Displayed

 
		
The table below describes the significant fields shown in the display. 
		

 
		

Table 61 show otv route Field Descriptions
Field 
				



Description 
				






Inst 
				



 The OTV overlay instance. 
				





VLAN
				



 The VLAN that is advertised with the MAC address by IS-IS.
				





BD
				



 The ID of the bridge domain where the MAC address was learned.
				





MAC Address 
				



The learned MAC address. 
				





AD 
				



 Administrative distance of the route. Routes with a lower administrative distance are preferred over routes with a higher administrative distance. 
				





Owner 
				



 The component that added the route. 
				





Next Hops(s) 
				



 Interfaces, Ethernet service instances, or remote OTV edge device where packets for this MAC address will be forwarded.
				









 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 
 
						show otv isis 
					 

 
				  		
 
					 
 Displays the IS-IS status and configuration. 
					 

 
				  		







 
	 






show otv site


 
		
 To display Overlay Transport Virtualization (OTV) site information, use the 
		  show otv site command in privileged EXEC mode. 
		

 
	 


 
		
 show otv
 [ overlay
overlay-interface ] 
site
 
	 


Syntax Description
 
		

 
					  
						 overlay 
						overlay-interface 
						 
					  
				  


 
					 
 (Optional) Displays information about the specified overlay interface. The range is from 0 to 512. 
					 

 
				  		







 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 
					 
Cisco IOS XE Release 3.5S 
					 

 
				  		
 
					 
 This command was introduced. 
					 

 
				  		







 
	 


Usage Guidelines
 
		
 This command displays OTV site information such as the site bridge domain and neighbors within the site. If an overlay interface is specified, site adjacencies only in the same overlay are displayed. If the 
		  all keyword is specified, then even the site adjacencies that are not yet associated with an overlay are displayed. 
		

 
	 


Examples
 
		
 The following example shows how to display all the OTV site adjacencies: 
		

 
		
Router# show otv site

Site Adjacency Information (Site-VLAN: 1) (* - this device)

 Overlay1 Site-Local Adjacencies (Count: 2) 

  Hostname       System ID        Last Change Ordinal    AED Enabled Status
* ED3            0026.CB0D.0800   2w0d        0          site overlay
  ED5            0026.CB0D.0801   1w5d        1          site overlay

 
		
The table below describes the significant fields shown in the display. 
		

 
		

Table 62 show otv site Field Descriptions
Field 
				



Description 
				






Hostname 
				



The dynamic hostname of the system. 
				





System ID 
				



 The MAC address of the system. 
				





Last Change 
				



 Time (in weeks, days) since the site adjacency last changed. 
				





Ordinal 
				



 A zero-based value used for calculating the authoritative edge device (AED) for a VLAN. 
				





AED Enabled Status 
				



 The IS-IS adjacency type used for determining AED status. 
				









 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 
 
						otv site bridge-domain 
					 

 
				  		
 
					 
Configures a bridge domain for sending IS-IS hellos over site interfaces. 
					 

 
				  		



 
					 
 
						otv site-identifier 
					 

 
				  		

Configures a site identifier for an OTV site. 
				  





 
					 
 
						show otv isis 
					 

 
				  		
 
					 
 Displays the IS-IS status and configuration. 
					 

 
				  		







 
	 






show otv statistics


 
		
To display Overlay Transport Virtualization (OTV) statistics, including some internal message counters, use the 
		  show otv statistics command in privileged EXEC mode. 
		

 
	 


 
		
 show otv statistics
 
	 


Syntax Description
 
		
This command has no arguments or keywords. 
		

 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 Cisco IOS XE Release 3.5S 
				  


 
					 
 This command was introduced. 
					 

 
				  		







 
	 


Examples
 
		
 The following is sample output from the 
		  show otv statistics command: 
		

 
		
Router# show otv statistics

OTV App Statistics
 RIB route update messages sent: 30
  Success responses: 30
  Sys Limit Failure responses: 0
  Topo Limit Failure responses: 0
  Sys and Topo Limit Failure responses: 0
  Other Failure responses: 0
 RIB route delete messages sent: 27
  Success responses: 27
  Not Found Failure responses: 0
  Other Failure responses: 0
 RIB route lookup messages sent: 668
  Route found responses: 0
  Route not found responses: 668
  Failure responses: 0

 OTV App Event Count:
  Invalid event                      : 0
  Configured control-group           : 3
  Configured data-group              : 2
  Configured join-interface          : 2
  Configured ARP/ND suppression      : 2
  Configured active-source           : 59
  Configured fragmentation           : 1
  External interface address change  : 0
  Bridge-domain VLAN assigned        : 17
  Bridge-domain VLAN unassigned      : 0
  Request to walk topologies         : 2
  Request for topology VLAN          : 0
  Request to walk multicast mappings : 27
  AED change pending notification    : 26
  Delete feature data                : 0
  MLRIB event received               : 268
  Send MLRIB MAC flood update        : 0
  Send MLRIB redist registration     : 2
  First/Last Overlay event           : 1
  Tunnel repopulation request        : 0
  Multicast HA DG sync               : 0
  Multicast HA checkpoint mapping    : 0
  ISIS mapping received              : 1263
  ISIS overlay adjacency change      : 182
  ISIS NSF mapping complete          : 0
  ISIS NSF adjacency complete        : 0
  Send MLRIB repopulation complete   : 0
  MLRIB NSF redistribution complete  : 0
  Join-interface OIR event           : 0

 
		
The table below describes the significant fields shown in the display. 
		

 
		

Table 63 show otv statistics Field Descriptions
Field 
				



Description 
				






RIB route update messages sent 
				



 Total number of update messages sent to the MLRIB. 
				





RIB route delete messages sent 
				



 Total number of delete messages sent to the MLRIB. 
				





RIB route lookup messages sent 
				



 Total number of route lookup messages sent to the MLRIB. 
				





OTV App Event Count 
				



 Number of OTV events processed by the system. 
				









 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 
 
						show otv isis 
					 

 
				  		
 
					 
 Displays the IS-IS status and configuration. 
					 

 
				  		







 
	 






show otv summary


 
		
 To display a table of all the Overlay Transport Virtualization (OTV) overlays configured on an edge device, use the 
		  show otv summary command in privileged EXEC mode. 
		

 
	 


 
		
 show otv summary
 
	 


Syntax Description
 
		
This command has no arguments or keywords. 
		

 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 Cisco IOS XE Release 3.5S 
				  


 
					 
 This command was introduced. 
					 

 
				  		







 
	 


Examples
 
		
 The following is sample output from the 
		  show otv summary command: 
		

 
		
Router# show otv summary

OTV Configuration Information, Site Bridge-Domain: 4

Overlay VPN Name        Control Group   Data Group(s)     Join Interface State
1       Northeast       225.22.22.22    232.5.0.0/8       Gi0/0/0        UP
2       Southwest       225.11.11.11    232.6.0.0/8       Gi0/0/1        DOWN
Total Overlay(s): 2

 
		
The table below describes the significant fields shown in the display. 
		

 
		

Table 64 show otv summary Field Descriptions
Field 
				



Description 
				






Overlay 
				



 Overlay interface ID. 
				





VPN Name 
				



 The OTV VPN name configured on the overlay interface.
				





Control Group 
				



 The IP multicast address used by OTV to form the overlay.
				





Data Group(s) 
				



 IP multicast addresses used for sending local IP multicast packets across the core.
				





Join Interface 
				



 The interface used for sending Internet Group Management Protocol (IGMP) joins towards the core.
				





State 
				



 The current state of the overlay interface. 
				









 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 
 
						show otv isis 
					 

 
				  		
 
					 
 Displays the IS-IS status and configuration. 
					 

 
				  		







 
	 






show otv vlan


 
		
 To display VLAN information for the Overlay Transport Virtualization (OTV) overlay interface, use the 
		  show otv vlan command in privileged EXEC mode. 
		

 
	 


 
		
 show otv
 [ overlay
overlay-interface ] 
vlan
 [ authoritative ] 
 
	 


Syntax Description
 
		

 
					  
						 overlay 
						overlay-interface 
						 
					  
				  


 
					 
 (Optional) Displays information about the specified overlay interface. The range is from 0 to 512. 
					 

 
				  		



 
						 authoritative 
						 
					  
				  


 
					 
(Optional) Displays only authoritative VLANs. 
					 

 
				  		







 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 
					 
Cisco IOS XE Release 3.5S 
					 

 
				  		
 
					 
 This command was introduced. 
					 

 
				  		







 
	 


Usage Guidelines
 
		
 If an overlay interface is specified, information for that overlay only is displayed; otherwise information for all overlays is displayed. When the 
		  authoritative keyword is specified, only those VLANs are displayed for which this device is the authoritative edge device (AED). 
		

 
	 


Examples
 
		
 The following example shows how to display VLAN information for the OTV overlay interface: 
		

 
		
Router# show otv overlay 1 vlan

Key:  SI - Service Instance
Overlay 1 VLAN Configuration Information
 Inst VLAN  Bridge-Domain  Auth  Site Interface(s)
 0    10    10             yes   Gi0/0/4:SI2
 0    11    11             yes   Gi0/0/4:SI3
 0    12    12             yes   Gi0/0/4:SI4
 Total VLAN(s): 3
 Total Authoritative VLAN(s): 3

 
		
The table below describes the significant fields shown in the display. 
		

 
		

Table 65 show otv vlan Field Descriptions
Field 
				



Description 
				






Inst 
				



 The OTV overlay instance. 
				





VLAN 
				



 The VLAN used by OTV when advertising local addresses.
				





Bridge-Domain 
				



 The ID of the local bridge domain associated with the given VLAN.
				





Auth 
				



 Authoritative status to indicate whether the edge device is authoritative and is forwarding traffic for the given VLAN.
				





Site Interface(s) 
				



 Interfaces and Ethernet service instances connected to the site network.
				









 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 
 
						show otv isis 
					 

 
				  		
 
					 
 Displays the IS-IS status and configuration. 
					 

 
				  		







 
	 






show parameter-map type waas




 
		
To display the parameter type configured for a Cisco Wide Area Application Services (WAAS) optimization, use the 
		  show parameter-map type waas command in privileged EXEC mode. 
		

 
	 


 
		
show 
				
parameter-map
type
waas 
				parameter-map-name
 
	 


Syntax Description
 
		

 
					  
						 parameter-map-name 
						 
					  
				  
 
					 
 Name of the configured Cisco WAAS parameter map. 
					 

 
				  		







 
	 


Command Modes
 
		
 Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  
Modification 
				  




 15.1(2)T 
				  
 
					 
 This command was introduced. 
					 

 
				  		







 
	 


Examples
 
		
The following is sample output from the 
		  show parameter-map type waas command: 
		

 
		
Device# show parameter-map type waas waas_global
        
parameter-map type waas waas_global 
 tfo optimize full
 tfo auto-discovery blacklist enable
 tfo auto-discovery blacklist hold-time 60
 lz entropy-check
 no dre uplink
 accelerator http
   enable
   metadatacache enable
   metadatacache https enable
   metadatacache max-age 100
   metadatacache min-age 5
   suppress-server-encoding enable
 accelerator cifs
 accelerator ssl
    waas-ssl-trustpoint TP-self-signed-27050293
    cipher-list waas_global
    . 
    .
    .
    services host-service peering
      version all
      peer-cipherlist waas_global
  enable
      

 
	 


Related Commands
 
		

Command 
				  
Description 
				  




 
					 
show policy-map type waas 
					 

 
				  		
 
					 
 Displays the policy map rules configured for a Cisco WAAS optimization policy map. 
					 

 
				  		







 
	 






show policy-map type mace


 
		
 To display policy-map statistics for the Measurement, Aggregation, and Correlation Engine (MACE), use the 
		  show 
			 policy-map 
			 type 
			 mace command in privileged EXEC mode. 
		

 
	 


 
		
show
policy-map
type
mace
 [  mace-name
 [ class
name ]   | apn
number  | interface
 [ type
number
 [  vc
 [ vpi/ 
								 ] 
vci  | vp
vpi
 [subinterface]   ]  ] 
 [  input
 [ class
name ]   | output
 [ class
name ]   ]   | session
 [ uid
 [session-id]  ] 
 [  input
 [ class
name ]   | output
 [ class
name ]   ]   ] 
 
	 


Syntax Description
 
		

 
					 
 
						 
						  mace-name 
						 
					 

 
				  		
 
					 
 (Optional) Name of the policy map. 
					 

 
				  		



 
					 
 
						 
						  class 
						 
						 
						  name 
						 
					 

 
				  		
 
					 
 (Optional) Displays quality of service (QoS) policy actions for an individual class map. 
					 

 
				  		



 
					 
 
						 
						  apn 
						 
					 

 
				  		
 
					 
 (Optional) Displays Access Point Name (APN)-related policy information. 
					 

 
				  		



 
					 
 
						 
						  number 
						 
					 

 
				  		
 
					 
 Number of the APN index. The range is from 1 to 65535. 
					 

 
				  		



 
					 
 
						 
						  interface 
						 
					 

 
				  		
 
					 
 (Optional) Displays the interface on which the QoS policy is configured. 
					 

 
				  		



 
					 
 
						 
						  type 
						  number 
						 
					 

 
				  		
 
					 
 (Optional) Interface type and number. For more information, use the question mark (?) online help function. 
					 

 
				  		



 
					 
 
						 
						  vc 
						 
					 

 
				  		
 
					 
 (Optional) Displays the virtual circuit (VC) service policy. 
					 

 
				  		



 
					 
 
						 
						  vp 
						 
					 

 
				  		
 
					 
 (Optional) Displays the virtual path (VP) service policy. 
					 

 
				  		



 
					 
 
						 
						  vpi/ 
						 
					 

 
				  		
 
					 
 (Optional) Virtual path identifier (VPI) of the VP. The range is 0 to 255. 
					 

 
				  		



 
					 
 
						 
						  vci 
						 
					 

 
				  		
 
					 
 Virtual channel identifier (VCI) of the VC associated with this VP. The range is 1 to 65535. 
					 

 
				  		



 
					 
 
						 
						  subinterface 
						 
					 

 
				  		
 
					 
 (Optional) Subinterface, where applicable. The accepted values for this field are: 
					 

 
					 
  •  cef-exception-- Cisco Express Forwarding (CEF)-exception subinterface. 
						
    

    • 

  •  host--Host subinterface. 
						
    

    • 

  •  transit--Transit subinterface. 
						
    

    • 


 
				  		



 
					 
 
						 
						  input 
						 
					 

 
				  		
 
					 
 (Optional) Displays the input policy of the session. 
					 

 
				  		



 
					 
 
						 
						  output 
						 
					 

 
				  		
 
					 
 (Optional) Displays the output policy of the session. 
					 

 
				  		



 
					 
 
						 
						  session 
						 
					 

 
				  		
 
					 
 (Optional) Displays the QoS policy session. 
					 

 
				  		



 
					 
 
						 
						  uid 
						 
					 

 
				  		
 
					 
 (Optional) Displays the session information based on the Subscriber Service Switch (SSS) unique ID. 
					 

 
				  		



 
					 
 
						 
						  session-id 
						 
					 

 
				  		
 
					 
 (Optional) Unique ID of the session. The range is from 1 to 65535. 
					 

 
				  		







 
	 


Command Modes
 
		


Privileged EXEC (#)

 
	 


 
		
Command History


 
					 
 Release 
					 

 
				  		
 
					 
 Modification 
					 

 
				  		




 
					 
 15.1(4)M 
					 

 
				  		
 
					 
 This command was introduced. 
					 

 
				  		







 
	 


Examples
 
		
 The following is sample output from the 
		  show 
			 policy-map 
			 type 
			 mace command: 
		

 
		
Router# show policy-map type mace mace_global
interface Ethernet1/0 
Service-policy mace input: mace_global
Class-map: c1 (match-any)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: tcp any 
0 packets, 0 bytes
5 minute rate 0 bps
Class-map: c2 (match-any)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: tcp any 
0 packets, 0 bytes
5 minute rate 0 bps
Class-map: c3 (match-any)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: tcp any 
0 packets, 0 bytes
5 minute rate 0 bps
Class-map: class-default (match-any)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any 


 
		
 The table below describes the significant fields shown in the display. 
		

 
		

Table 66 show policy-map type mace Field Descriptions
 
				  
 Field 
				  

 
						
 
				  
 Description 
				  

 
						




 
				  
 Service-policy 
				  

 
						
 
				  
 Displays the service policy that is configured as a traffic shaping policy within a policy map. 
				  

 
						



 
				  
 Class-map 
				  

 
						
 
				  
 Displays a class map configuration that is created to be used for matching packets to a specified class. 
				  

 
						







 
	 


Related Commands
 
		

 
					 
 Command 
					 

 
				  		
 
					 
 Description 
					 

 
				  		




 
					 
 
						 
						  policy-map 
						  type 
						  mace 
						 
					 

 
				  		
 
					 
 Configures a MACE policy map and enters policy-map configuration mode. 
					 

 
				  		



 
					 
 
						 
						  show 
						  policy-map 
						 
					 

 
				  		
 
					 
 Displays the configuration of all classes for a specified service policy map or all classes for all existing policy maps. 
					 

 
				  		







 
	 






show policy-map type waas




 
		
To display the policy map rules configured for a Cisco Wide Area Application Services (WAAS) optimization policy map, use the 
		  show policy-map type waas command in privileged EXEC mode. 
		

 
	 


 
		
show 
				
policy-map
type
waaspolicy-map-name
 
	 


Syntax Description
 
		

 
					  
						 policy-map-name 
						 
					  
				  
 
					 
Name of the configured Cisco WAAS policy map. 
					 

 
				  		







 
	 


Command Modes
 
		
 Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  
Modification 
				  




 15.1(2)T 
				  
 
					 
This command was introduced. 
					 

 
				  		







 
	 


Examples
 
		
 The following is sample output from the 
		  show policy-map type waas command: 
		

 
		
Device# show policy-map type waas waas_global 

Policy Map type waas waas_global
	sequence-interval 10
10 Class AFS
	 optimize dre lz application Web
20 Class Http
	 optimize lz application Filesystem
30 Class class-default

 
	 


Related Commands
 
		

Command 
				  
Description 
				  




 
					 
 
						show parameter-map type waas 
					 

 
				  		
 
					 
 Displays the parameter type configured for Cisco WAAS optimization. 
					 

 
				  		







 
	 






show platform hardware qfp feature otv client interface


 
		
 To display Overlay Transport Virtualization (OTV) feature-specific information for the specified overlay interface, use the 
		  show platform hardware qfp feature otv client interface command in privileged EXEC mode. 
		

 
	 


 
		
 show platform hardware qfp
 { active | standby } 
feature otv client interface
name
 
	 


Syntax Description
 
		

 
					  
						 active 
						 
					  
				  


 
					 
 Displays information about the active instance of the processor. 
					 

 
				  		



 
					  
						standby 
					  
				  


 
					 
 Displays information about the standby instance of the processor. 
					 

 
				  		



 
						name 
					  
				  


 
					 
 Name of the interface on which OTV is configured. 
					 

 
				  		







 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 
					 
Cisco IOS XE Release 3.5S 
					 

 
				  		
 
					 
 This command was introduced. 
					 

 
				  		







 
	 


Examples
 
		
 The following is sample output from the 
		  show platform hardware qfp feature otv client interface command: 
		

 
		
Router# show platform hardware qfp active feature otv client interface Overlay10

otv info:
  QFP interface handle: 8
  rx uidb: 245752  tx uidb: 245752
  config complete: False
  OCE type: Invalid
  oce_chain_p : 0x00010063
  Decap chain configured: True
  debug_flags : 0x0000ecaf
  ISIS Enabled: True

 
		
 The table below describes the significant fields shown in the display. 
		

Table 67 show platform hardware qfp active feature otv client interface Field Descriptions
Field 
				



Description 
				






QFP interface handle 
				



 An internal identifier assigned by the quantum flow processor (QFP) software for this interface. 
				





rx uidb 
				



 An internal identifier for the receive side of the interface. 
				





tx uidb 
				



 An internal identifier for the transmit side of the interface. 
				





ISIS Enabled 
				



 Indicates whether or not IS-IS routing is enabled on the interface. 
				









 
		

 
	 






show platform software frame-relay



      

To display the statistics about frame relay permanent virtual circuits (PVCs), use the show platform software frame-relay command in the privileged EXEC mode. 


    



      
show
platform
software
frame-relay
slot
pvc
 [  interface
interface  | dlci
number  ] 

    


Syntax Description

      


                

                  slot
                


              		

                

(Optional) Embedded Service Processor or Route Processor slot. 


                

Valid options are: 


                
  • 
F0—Embedded-Service-Processor slot 0
    

    • 

  • 
F1—Embedded-Service-Processor slot 1
    

    • 

  • 
FP—Embedded-Service-Processor
    

    • 

  • 
R0—Route-Processor slot 0
    

    • 

  • 
R1—Route-Processor slot 1
    

    • 

  • 
RP—Route-Processor
    

    • 



              		




                

                  
                    interface
                  
                


              		

                

(Optional) Indicates the specific interface for which PVC information will be displayed.


              		




                

                  
                    dlci
                  
                


              		

                

(Optional) Indicates the specific DLCI number used on the interface. Statistics pertaining to the specified PVC are displayed when a DLCI is specified.


                

The valid value range is 16 to 1022.


              		








    


Command Modes

      


Privileged EXEC (#) 


    



      
Command History



                

Release


              		

                

Modification


              		





                

Cisco IOS XE Release 2.1


              		

                

This command was introduced. 


              		








    


Examples

      

The following is a sample output from the show paltform software frame-relay rp active pvc command displaying the forwarding manager frame relay PVC information: 


      
router#show platform software frame-relay rp active pvc
Forwarding Manager Frame Relay PVC Information
Interface       DLCI        ID       QFP ID    Bandwidth  Fragm...  
Serial0/1...     61      0x1020012      0          0          0     
MFR1.1           100     0x1020013      0          0          0 



    






show platform software l2fib fp


 
		
To display the global bridge domain table for MAC and Layer 2 multicast on the Forwarding Manager (FMAN) on Forwarding Processor (FP), use the 
		  show platform software l2fib fp command in privileged EXEC mode. 
		

 
	 


 
		
 show platform software l2fib fp
 { active | standby } 
 {  bd
bridge-domain-ID
 {  unicast
 { all | mac
mac-string  }   | v4
group
 {  group-addr
source
source-addr  | all }   | v6
group
addr
 { all | source
source-addr  }   }   | mlist
 {  index
mcast-index  | internal | summary | table }   } 
 
	 


Syntax Description
 
		

 
					  
						 active 
						 
					  
				  


 
					 
 Displays information about the active instance of the processor. 
					 

 
				  		



 
					  
						standby 
					  
				  


 
					 
 Displays information about the standby instance of the processor. 
					 

 
				  		



 
					  
						bd 
						bridge-domain-ID 
					  
				  



Displays information about the specified bridge domain. The range is from 1 to 100000. 
				  





 
					  
						 unicast 
						 
					  
				  



Displays the Layer 2 Forwarding Information Base (L2FIB) unicast information. 
				  





 
					  
						all 
					  
				  



Displays all MAC prefixes. 
				  





 
					  
						mac 
						mac-string 
				  



Displays L2FIB MAC information for the specified MAC string. 
				  





 
					  
						v4 group 
						group-addr 
				  



Displays IPv4 multicast group information for the specified group address. 
				  





 
					  
						source 
						source-addr 
				  



Displays IPv4 multicast source information for the specified source address. 
				  





 
					  
						all 
					  
				  



Displays all IPv4 prefixes. 
				  





 
					  
						v6 group 
						addr 
				  



Displays IPv6 multicast group information for the specified group address. 
				  





 
					  
						all 
					  
				  



Displays all IPv6 prefixes. 
				  





 
					  
						source 
						source-addr 
				  



Displays IPv6 multicast information for the specified source address. 
				  





 
					  
						mlist 
					  
				  



Displays an output list. 
				  





 
					  
						index 
						mcast-index 
				  



Displays the specified multicast list platform index. The range is from 0 to 4294967295.
				  





 
					  
						 internal 
						 
					  
				  



Displays a management internals output list. 
				  





 
					  
						summary 
					  
				  



Displays a summary output list. 
				  





 
					  
						table 
					  
				  



Displays a table output list. 
				  









 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 
					 
Cisco IOS XE Release 3.5S 
					 

 
				  		
 
					 
 This command was introduced. 
					 

 
				  		







 
	 


Examples
 
		
 The following is sample output from the 
		  show platform software l2fib fp command to display IPv4 multicast group information: 
		

 
		
Router# show platform software l2fib fp active bd 10 v4 group all

Forwarding Manager L2FIB Mprefix Table

Prefix             Prefix Len       BD         Olist id         Prefix Id        Input If         
-------------------------------------------------------------------------------------------
*, 224.0.0.0/0     4                10         0x7              0x24             0                
*, 224.0.0.0/0     24               10         0xfa6            0x3ea3           0                
*, 224.0.1.39/0    32               10         0xfa6            0x3ea4           0                
*, 224.0.1.40/0    32               10         0xfa6            0x3ea5           0

 
		
 The following is sample output from the 
		  show platform software l2fib fp command to display L2FIB unicast information: 
		

 
		
Router# show platform software l2fib fp active bd 10 unicast all

MAC                        BD               Nhop type        Nhop Idx         Flags            
ffff.ffff.ffff             10               olist            4006                  

 
		
The table below describes the significant fields shown in the display. 
		

 
		

Table 68 show platform software l2fib fp Field Descriptions
Field 
				



Description 
				






Prefix 
				



The IP multicast address in the 
				  group-address, 
					 source-address format. 
				





Prefix Len 
				



The prefix length the of the IP multicast address. 
				





BD 
				



The bridge domain ID. 
				





Olist id 
				



The multicast replication list ID. 
				





Prefix Id 
				



The platform ID allocated for the IP multicast prefix. 
				





Input If 
				



The input Ethernet Flow Point (EFP) for the IP multicast prefix. 
				





MAC 
				



The Ethernet MAC address. 
				





Nhop type 
				



The next hop type for the Ethernet MAC address. 
				





Nhop Idx 
				



The platform ID assigned for the next hop of the Ethernet MAC address. 
				





Flags 
				



Attributes associated with the Ethernet MAC address. 
				









 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 show platform software l2fib rp 
				  


 
					 
 Displays the global bridge domain table for MAC and multicast on the FMAN on RP. 
					 

 
				  		







 
	 






show platform software l2fib rp


 
		
To display the global bridge domain table for MAC and multicast on the Forwarding Manager (FMAN) on the Route Processor (RP), use the 
		  show platform software l2fib rp command in privileged EXEC mode. 
		

 
	 


 
		
 show platform software l2fib rp
 { active | standby }  mlist
 {  index
mcast-index  | internal | summary | table }  
 
	 


Syntax Description
 
		

 
					  
						 active 
						 
					  
				  


 
					 
 Displays information about the active instance of the processor. 
					 

 
				  		



 
					  
						standby 
					  
				  


 
					 
 Displays information about the standby instance of the processor. 
					 

 
				  		



 
					  
						mlist 
					  
				  



Displays an output list. 
				  





 
					  
						index 
						mcast-index 
				  



Displays the specified multicast list platform index. The range is from 0 to 4294967295.
				  





 
					  
						 internal 
						 
					  
				  



Displays a management internals output list. 
				  





 
					  
						summary 
					  
				  



Displays a summary output list. 
				  





 
					  
						table 
					  
				  



Displays a table output list. 
				  









 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 
					 
Cisco IOS XE Release 3.5S 
					 

 
				  		
 
					 
 This command was introduced. 
					 

 
				  		







 
	 


Examples
 
		
 The following is sample output from the 
		  show platform software l2fib rp command: 
		

 
		
Router# show platform software l2fib rp active mlist index 4006

L2FIB Mlist entries

Type  Index  AOM ID  CPP Info
efp   3ea1   OM:     0x42ad659c 
oce   8f01   OM:     0x43877dc4

 
		
The table below describes the significant fields shown in the display. 
		

 
		

Table 69 show platform software l2fib rp Field Descriptions
Field 
				



Description 
				






Type 
				



The type of replication entries in the multicast replication list. 
				





Index 
				



The platform ID allocated for the multicast replication entry. 
				





AOM ID 
				



An internal object ID associated with the multicast replication entry. 
				





CPP Info 
				



The memory address allocated data-plane driver for the multicast replication entry. 
				









 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 show platform software l2fib fp 
				  


 
					 
Displays the global bridge domain table for MAC and Layer 2 multicast on the FMAN on FP. 
					 

 
				  		







 
	 






show platform software mfr



      

To display statistics about multilink frame relay information, use the show platform software mfrcommand in the privileged EXEC mode. 


    



      
show
platform
software
mfr
slot
 {  active
 [ counter | index ]   | standby } 

    


Syntax Description

      


                

                  slot
                


              		

                

(Optional) Embedded Service Processor or Route Processor slot. 


                

Valid options are: 


                
  • 
F0—Embedded-Service-Processor slot 0
    

    • 

  • 
F1—Embedded-Service-Processor slot 1
    

    • 

  • 
FP—Embedded-Service-Processor
    

    • 

  • 
R0—Route-Processor slot 0
    

    • 

  • 
R1—Route-Processor slot 1
    

    • 

  • 
RP—Route-Processor
    

    • 



              		




                

                  
                    active
                  
                


              		

                

Displays the active instance of the MFR.


              		




                

                  
                    counter
                  
                


              		

                

(Optional) MFR messaging counter information.


              		




                

                  
                    index
                  
                


              		

                

(Optional) MFR FP information pertaining to a specific index. The valid value range is 0 to 1000000.


              		








    


Command Modes

      


Privileged EXEC (#) 


    



      
Command History



                

Release


              		

                

Modification


              		





                

Cisco IOS XE Release 3.4S


              		

                

This command was introduced. 


              		








    


Examples

      

The following is a sample output from the show paltform software mfr fp active counters command displaying the forwarding manager MFR message counters: 


      
router#show platform software mfr fp active counter
 
Forwarding Manager MFR Message Counters
MFR Bundle additions         : 2
MFR Bundle deletions         : 0
MFR Bundle modifications     : 0
MFR Bundle errors            : 0
MFR Deferred Bundles         : 0
MFR Member Link additions    : 0
MFR Member Link deletions    : 0
MFR Member Link modifications: 0
MFR Member Link errors       : 0
MFR Deferred Links           : 0



      

      


    






show platform software otv fp


 
		
To display the overlay configuration on an Overlay Transport Virtualization (OTV) edge device on the Forwarding Manager (FMAN) on Forwarding Processor (FP), use the 
		  show platform software otv fp command in privileged EXEC mode. 
		

 
	 


 
		
 show platform software otv fp
 { active | standby } 
 {   { decap-oce | encap-oce } 
 [ index
index ] 
 [all]   | oce-stats | site-isis
efp-dpidx  } 
 
	 


Syntax Description
 
		

 
					  
						 active 
						 
					  
				  


 
					 
 Displays information about the active instance of the processor. 
					 

 
				  		



 
					  
						standby 
					  
				  


 
					 
 Displays information about the standby instance of the processor. 
					 

 
				  		



 
						decap-oce 
					  
				  



Displays the OTV decapsulation object chain element (OCE). 
				  





 
						encap-oce 
					  
				  



Displays the OTV encapsulation OCE. 
				  





 
						index 
						index 
					  
				  



(Optional) Displays the specified OTV decapsulation OCE platform index. The range is from 0 to 4294967295. 
				  





 
						all 
					  
				  



(Optional) Displays all entries starting from the specified decapsulation OCE index. 
				  





 
						oce-stats 
					  
				  



Displays OTV OCE statistics. 
				  





 
						site-isis 
						efp-dpidx 
					  
				  



Displays the specified OTV site Intermediate System-to-Intermediate System (IS-IS) bridge domain Ethernet Flow Point (EFP) DPIDX (the internal platform index). The range is from 1 to 4294967295. 
				  









 
	 


Command Modes
 
		
Privileged EXEC (#)

 
	 


 
		
Command History


Release 
				  



Modification 
				  






 
					 
Cisco IOS XE Release 3.5S 
					 

 
				  		
 
					 
 This command was introduced. 
					 

 
				  		







 
	 


Examples
 
		
 The following is sample output from the 
		  show platform software otv fp command: 
		

 
		
Router# show platform software otv fp active encap-oce

Number of OTV Encap OCE entries in the table: 81

OTV Encap OCE: id 0x8f01, encap type MPLS_GRE, str 0x2a1ff
  Next OCE: type OBJ_ADJACENCY, id 0x8e25
  Overlay EFP: dpidx 0x10202de
  Flags: BCAST_PAK, STP_PAK, UNKNOWN_PAK
  Misc Info: CPP handle: 0x133dbe18 (om_id 65315 created)

OTV Encap OCE: id 0x8f02, encap type MPLS_GRE, str 0x2fb1ff
  Next OCE: type OBJ_ADJACENCY, id 0x8e25
  Overlay EFP: dpidx 0x10202df
  Flags: BCAST_PAK, STP_PAK, UNKNOWN_PAK
  Misc Info: CPP handle: 0x133e14b8 (om_id 65316 created)

OTV Encap OCE: id 0x8f03, encap type MPLS_GRE, str 0x2fc1ff
  Next OCE: type OBJ_ADJACENCY, id 0x8e25
  Overlay EFP: dpidx 0x10202e0
  Flags: BCAST_PAK, STP_PAK, UNKNOWN_PAK
  Misc Info: CPP handle: 0x133dbe50 (om_id 65317 created)


 
		
The table below describes the significant fields shown in the display. 
		

 
		

Table 70 show platform software otv fp Field Descriptions
Field 
				



Description 
				






OTV Encap OCE 
				


 
				  
The OTV encapsulation Output Chain Element (OCE). 
				  

 
						



id 
				



The platform ID allocated for OTV encapsulation OCE. 
				





encap type 
				



The encapsulation format. 
				





str 
				



The OTV encapsulation header. 
				





Next OCE 
				



The OCE following the OTV encapsulation OCE. 
				





Overlay EFP 
				



The platform interface ID for the Ethernet Flow Point (EFP) associated with the OTV encapsulation OCE. 
				









 
	 


Related Commands
 
		

Command 
				  



Description 
				  






 
					 show platform software l2fib fp 
				  


 
					 
Displays the global bridge domain table for MAC and Layer 2 multicast on the FMAN on FP.